Life Fitness 91Ti Treadmill User Manual
Contents
1. Wires to Speaker Insert the supplied bracket bolt up through the bottom of the bracket and terminal cover and screw it into the threaded insert on the underside of the speaker The bolt should be snug but not so tight as to prevent the bracket from pivoting The wall mounted speaker may be pivoted from side to side however the bracket is not designed to be tilted up or down and Overhead View Openings on top a round screw hole and an arc shaped opening in front of it The speaker cable should be threaded through the arc attempting to tilt it will damage the bracket shaped opening not the screw hole and possibly the wall which would not be Attach the bracket to the wall plate by inserting covered by your warranty the tab at the top of the wall plate into the slot on top of the bracket and snapping the bracket onto the wall plate Thread the cable through the round opening in the terminal cover and then insert the Wall speaker wires into the terminals on the underside of the speaker remembering to observe the correct polarity see page 9 Place the terminal cover over the opening on the underside of the speaker so that it i fits flush against the speaker and covers the i terminals with its round opening exposing 23mm M6 1 25P the threaded insert The bracket fits through or 3 4 the round opening in the terminal cover or 1 4 20 Speaker Level Connec2. This switch determines whether the SUB 1S18 subwoofer s piston like action moves in and out in phase with the main speakers If the speakers were to play out of phase the sound waves pro duced by the subwoofer would be canceled out reducing bass response This phenome non depends in part on the relative place ment of the speakers in the room In most cases the Phase Switch should be left in the NORMAL position However it does no harm to experiment with the Phase Switch and you may leave it in the position that maximizes bass response Line Level Subwoofer SUB Input Connect the subwoofer outout of a receiver with digital surround sound decoding such as Dolby Digital or DTS to this input This input bypasses the SUB 1S18 s internal crossover circuitry and should only be used with a filtered signal If your receiver does not have digital decoding you should use the Line Level Full Range Inputs instead Line Level Full Range Inputs Connect the line level subwoofer outout or preamp out put s of your receiver or amplifier to these inputs If your receiver does not have a sepa rate subwoofer output use a Y adapter not Supplied to bridge the receiver s preamp out put to the main amp input for that channel and connect the long end of the adapter to the corresponding line level input on the SUB TS18 If your receiver has only a single Subwoofer output you may connect it to either the left or
3. audio sense Included One center channel speaker One powered subwoofer e Four satellites for left right and surrounds with color key stickers mounted on shelf stands e Four leatherette coasters eere Four wall mount brackets oo One 15 RCA cable for connection to subwoofer purple One 15 mini plug cable for use with external trigger input black Da N gt E gt C Three 20 speaker cables for connection to front satellites red and white and to center speaker green gt C Da s Two 40 speaker cables for connection from receiver to rear satellites gray and blue SUB TSI8 SUBWOOFER AMPLIFIER SUBWOOFER LEVEL FILTER ON MIN MAX OFF Hi x eee EXT TRIGGER AUTO i ee eae Q Q 0 0 Q Q 0 0 OUT IN IMPORTANT CONNECT STRIPED WIRE TO RED SPEAKER TERMINAL 00 Q00 rmcemr IO I 60 Subwoofer Level Control High Cut Low Pass Filter Switch 6 External Trigger Input Audio Sense On Off Switch Subwoofer Level Control Volume may be adjusted using the Subwoofer Level Control Turn the control clockwise to increase the SUB TS18 s volume or counterclockwise to decrease it High Cut Low Pass Filter Switch Placing this switch in the ON position acti vates circuitry that cuts out all audio input signals above 120HZ allowing the SUB 1S18 to focus its power on reproducing the low frequency po
4. depending on whether or not a signal is being sent to it by your receiver or surround processor and provided that the Audio Sense On Off Switch is moved down so that it is in the AUT O position When your receiver or amplifier is off or is not sending program material to the sub woofer the subwoofer will be in Standby mode and the LED indicator on the top of the subwoofer will turn amber When the subwoofer senses an audio signal it will auto matically turn itself on and the LED indicator will turn blue If the subwoofer does not sense a signal after approximately 20 minutes it will automatically go into Standby mode When the Audio Sense On Off Switch is switched to the ON position the sub woofer will remain on whether or not pro gram material is playing and the LED indica tor will remain lit blue If your receiver processor or amplifier is equipped with a compatible trigger output you may connect it to the SUB 1518 s External Trigger Input When you turn on your component if you have set it up cor rectly it will send an electrical trigger signal to the SUB 1S18 which will cause the subwoofer to turn itself on even when the Audio Sense On Off Switch has been placed in the AU TO position and no audio signal is detected The trigger signal must be between 3 and 30 volts although it may be an AC or DC signal and an AC signal may be 50Hz or 6QHZ lf you ll be away from home for an extended per
5. or the third prong is provided for your safety If the provided plug does not fit Into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel servicing is required when the apparatus has been damaged in any way Such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Do not use attachments not recommended by the product manufacturer as they may cause hazards 16 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the oper
6. right line level input on the SUB TS 18 and no Y adapter is needed Speaker Level Outputs If you are using the Speaker Level Inputs on the SUB TS18 you should connect these binding post terminals to your front left and right speakers remembering to maintain polarity by connecting the terminal on the SUB TS18 subwoofer to the terminal on the speaker and the terminal on the SUB TS18 subwoofer to the terminal on the speaker If you are not using the Speaker Level Inputs then connect your front left and right speakers directly to your receiver or amplifier See pages 9 through 12 for further information on speaker connections Speaker Level Inputs If your receiver or amplifier does not have a line level sub woofer output connect these binding post terminals to the main left and right speaker terminals of your receiver or amplifier Remember to maintain polarity by connecting the terminal on the receiver amplifier to the terminal on the SUB 1S18 subwoofer and the terminal on the receiver amplifier to the terminal on the SUB TS18 subwoofer q Master Power Switch Place this Switch in the e position to power on the SUB 1S18 subwoofer The SUB TS18 will then be either in the Standby mode or com pletely on depending on the position of the Audio Sense On Off Switch AC Power Cord Make sure to plug this cord into an active unswitched electrical out
7. we urge you to take a few minutes to read through this manual This will ensure that connec tions to your receiver or preamp processor and amplifier or other external devices are made properly In addition a few minutes spent learning the functions of the controls will enhance the HKTS 18 s performance If you have any questions about this prod uct its installation or its operation please contact your dealer the best local source of information or visit our Web site at www harmankardon com Description and Features The HKTS 18 is a six piece home theater speaker system that includes a 10 inch 200 watt bass reflex powered subwoofer four identical two way dual midrange Satellite soeakers for use in the left and right front and rear speaker positions a voice matched dedicated dual driver center speaker shelf stands and wall mount brackets for the four satellites and all of the speaker cables you need to connect your speakers to your receiver or preamp processor and amplifier The speaker cables and speakers are all color coded to con form to the CEA standard simplifying setup especially when the system is used with a Harman Kardon receiver The HKTS 18 subwoofer is easy to connect to your system since it s equipped with a subwoofer input for use with equipment that has a dedicated subwoofer low frequency Output It also includes stereo speaker level inputs and outputs for connection to older rece
8. DTS or Other Center Digital Surround Mode Connection USE THIS INSTALLATION METHOD FOR Left DOLBY DIGITAL DTS OR OTHER DIGITAL a 1 SURROUND PROCESSORS F F SUB TS18 Subwoofer Use the line level input jack marked SUB ae LEVEL for the low frequency effects channel i Connect this jack to the subwoofer output 7 or LFE output on your receiver or amplifier Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure you ve configured your surround sound processor for Subwoofer On The lett roni eft Right front left front right center and surround speakers should all be set to Small ULE A AO When all connections have been made plug Out the AC power cord on the subwoofer into Surround Surround an AC outlet rue Center Right A 010 J C BO Surround T Right Receiver oi i 10 SPEAKER CONNECTIONS SPEAKER CONNECTIONS i7 Dolby Pro Logic oi Canter Non Digital Line Level Left USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS NOT DOLBY DIGITAL DTS OR OTHER DIGITAL ka ica PROCESSING WHERE THE RECEIVER i J PROCESSOR IS EQUIPPED WITH A SUBWOOFER OUTPUT OR A VOLUME CONTROLLED PREAMP LINE LEVEL OUTPUT Use the supplied RCA type interconnect cable to connect the line level subwoofer Output on your receiver or amplifier to either the left or right Line Level Ful
9. STALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS NOT DOLBY DIGITAL DTS OR OTHER DIGITAL PROCESSING WHERE THE RECEIVER PROCESSOR DOES NOT HAVE A SUB WOOFER OUTPUT OR A VOLUME CONTROLLED PREAMP LINE LEVEL OUTPUT Connect your receiver or amplifier s front left and right speaker terminals to the left and right Speaker Level Input termi nals on the SUB 1518 subwoofer that are marked High Level In Connect the left and right Speaker Level Output terminals on the SUB 1S18 subwoofer that are marked High Level Out to the correspond ing terminals on the back of your front left and right speakers Connect your receiver or amplifier s center and surround left and right speaker termi nals to the corresponding terminals on the back of your center and surround left and right speakers When all connections have been made plug the AC power cord on the subwoofer into an AC outlet 12 SPEAKER CONNECTIONS Front Left Center SUB TS18 Subwoofer H l we peg A S L E 1 A Jeg E g R 9 OT OUT IN ail H E a J fever _ i Receiver Front Left Center Front Right t t O00 YUO OW Surround Left Surround Right Surround Right Api ki Move the Master Power Switch marked Power to the e On position The SUB 1S18 subwoofer will automatically turn itself on or go into Standby mode
10. ating instructions 17 If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and require ments for the grounding electrode See Figure A 18 An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Figure A Example of Antenna Grounding as per National Electrical Code ANSI NFPA 70 19 Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 20 Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 21 The apparatus shall not be exposed to dr
11. between receiver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut punctured or touching other wires e f more than one pair of main speakers is being used check the minimum impedance requirements of your receiver amplifier e Make sure the SUB Input or Line Level Inputs of the SUB TS18 subwoofer and SUB or LFE output of your receiver or amplifier are properly connected by the RCA type interconnect cable e f you are using the SUB TS18 s Speaker Level Inputs check your speaker cables to make sure they are all connected that none of the wires are frayed cut punctured or touching other wires and that you have maintained the correct polarity by connecting positive terminals to positive terminals and negative terminals to negative terminals e Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch is Switched on to the e position e Check the speaker setup bass management settings in your A V receiver or processor to make certain that the front center and surround speakers are configured for Small and that the subwoofer is set for Yes or On e Check all wires and connections between receiver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut punctured or touching other wires e Review proper operation of your receiver processor and its surround sound featu
12. e External Trigger Input Voltage 3 30 Volts AC DC Dimensions H x W x D 18 7 8 x 13 3 8 x 13 3 8 479mm x 340mm x 340mm Weight 35 1 Ib 15 8kg The loudspeaker enclosures may be cleaned by gently wiping with a soft cotton or microfiber cloth Do not use water or any liquid cleaners Features specifications and appearance are subject to change without notice Harman Kardon is a trademark of Harman International Industries Incorporated registered in the United States and or other countries Designed to Entertain is a trademark of Harman International Industries Incorporated CEA is a registered trademark of the Consumer Electronics Association Dolby and Pro Logic are registered trademarks of Dolby Laboratories DTS is a registered trademark of DTS Inc axl S We SMEG e NGAT IONS Js harman kardon H A Harman International Company 250 Crossways Park Drive Woodbury New York 11797 916 255 HKHK 4545 Fax 516 682 3523 2006 Harman International Industries Incorporated All rights reserved Printed 10 06 Part No 406 000 05504 E
13. ers are placed along the circle about 30 degrees from the center speaker and angled toward the listener SPEAKER PLACEMENT Video Screen Subwoofer ront Left Speaker Side Surround 7 Left Speaker K for Side Surround Left Speaker It is best to place the front left right and center speakers as close to the same height as possible preferably about the same height as the listener s ears In any event the center soeaker should be no more than two feet above or below the left right speakers The side surround speakers should be placed 110 degrees from the center speaker that is slightly behind and angled toward the listener If this isn t feasible place the surround speakers behind the listener with each surround speaker facing the opposite side front speaker The surround speakers may be placed a little higher than the listener s ears ae i N Alternate placement Front Right Speaker Side Surround Right Speaker Y Alternate placement for Side Surround Right Speaker The subwoofer s location is less critical since low frequency sounds are omni directional Placing the subwoofer close to a wall or in a corner will reinforce the low fre quencies and may create a boomy sound You may wish to experiment over time by placing the subwoofer where the listener normally sits and then walking around the room u
14. harman kardon Designed to Entertain HKTS 18 HOME THEATER SPEAKER SYSTEM OWNER S MANUAL HKTS 18 HOME THEATER SPEAKER SYSTEM 3 Safety Information 4 Introduction 4 Included 5 SUB 1518 Subwoofer Amplifier Panel Controls and Connections 7 Speaker Placement 7 Color Coding System 8 Mounting Options 9 Speaker Connections 9 opeaker Level Connection Guide 10 Dolby Digital or DTS or Other Digital Surround Mode Connection 11 Dolby Pro Logic Non Digital Line Level 12 Dolby Pro Logic Non Digital Speaker Level 13 Operation 13 Volume 13 Additional Bass Adjustments 14 Troubleshooting 15 HKTS 18 Specifications Please register your product on our Web site at www harmankardon com Note You ll need the serial number of your new home theater speaker system At the same time you can choose to be notified about our new products and or special promotions Typographical Conventions In order to help you use this manual certain conventions have been used EXAMPLE bold type indicates a specific control or rear panel connection on the SUB TS18 subwoofer EXAMPLE OCR type indicates a control or switch position on the SUB TS18 subwoofer number in a circle indicates a rear panel control or connection on the SUB TS18 subwoofer 2 TABLE OF CONTENTS SAFETY INFORMATION Read First Important Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric s
15. hock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade
16. if the subwoofer attempted to repro duce higher frequencies This switch should be left in the ON position except 1 When the SUB Input is being used in which case it has no effect or 2 When the Speaker Level Inputs or the Line Level Full Range Inputs are being used with a crossover or filter aboard the receiver or processor In these two circumstances place the switch in the OF F position OPERATION 13 TROUBLESHOOTING SYMPTOM lf there is no sound from any of the speakers If there is no sound coming from one speaker If there is no sound from the center speaker If the system plays at low volumes but shuts off as volume is increased If there is low or no bass output If there is no sound from the surround speakers SOLUTION e Check that receiver amplifier is on and a source is playing e Check that the powered subwoofer is plugged in and its Master Power Switch is switched on to the e position e Check all wires and connections between recelver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut punctured or touching other wires e Review proper operation of your receiver amplifier e Check the Balance control on your receiver amplifier e Check all wires and connections between receiver amplifier and speakers Make sure all wires are connected Make sure none of the speaker wires are frayed cut punctured o
17. iod of time or if the subwoofer will not be used switch the Master Power Switch to the OF F position Volume Volume can be adjusted using the Sub woofer Level Control as shown Turn the control knob clockwise to increase the volume of the subwoofer and counterclockwise to decrease the subwoofer s volume Subwoofer iN Mn MAX Subwoofer Van Mn MAX qJ D AT D OPERATION Additional Bass Adjustments In addition to the volume adjustments described previously the SUB 1S18 subwoofer includes a Phase Switch and a Filter Switch that can be used to adjust the bass response to suit your listening environment or taste In most situations the Phase Switch should be left in the NORMAL position If you Suspect that the subwoofer is playing out of phase with the other speakers which would tend to diminish bass response try placing this switch in the REVERSE position There is no harm in experimenting and you may return the switch to the NORMAL position at any time If you rearrange your room and reposition the speakers it would be a good idea to check whether they are in phase by flipping this switch The High Cut Low Pass Filter Switch limits the frequencies of the audio signal inoutted to the subwoofer to the low fre quencies that the subwoofer reproduces best This allows the subwoofer to perform more efficiently and with superior bass reproduction minimizing distortion that might occur
18. ipping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 22 Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 23 When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 24 Upon completion of any service or repairs to this product ask the service technician to perform Safety checks to determine that the product is in proper operating condition 25 The product should be mounted to a wall or ceiling only as recommended by the manufacturer lt Antenna Lead In Wire Ground Clamp Antenna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Electric Service Equipment Ground Clamps Power Service Grounding Electrode System NEC Art 250 Part H SAFETY INFORMATION 3 INTRODUCTION Introduction Thank you for purchasing the Harman Kardon HKTS 18 with which you re about to begin many years of listening enjoyment The HKTS 18 has been custom designed to provide all the excitement and power of the cinema experience in your own living room To obtain maximum enjoyment from your new home theater speaker system
19. ivers and processors that do not have a line level subwoofer output Other conve 4 INTRODUCTION niences include a level control an external trigger input for automatic turn on when connected to a compatible product a high cut low pass filter switch and a phase Switch for fine tuning bass response to suit your listening environment and taste and audio sense auto turn on which senses the presence of an audio signal and automati Cally switches the unit from Standby mode to Active mode ohelf stands and wall mount brackets are included for the satellite speakers and optional HTFS 2 floor stands are available separately from your Harman Kardon dealer Harman Kardon invented the high fidelity receiver more than fifty years ago With State of the art features and time honored circuit designs the HKTS 18 is a perfect complement to a Harman Kardon receiver or any home theater system HM Complete home theater speaker system W identical dual midrange configura tion for satellites and center provides seamless pans W Speakers are magnetically shielded for placement near video monitors W Fully color coded cables and con nections simplify setup W Both line and speaker level inputs for use with most audio components W Subwoofer input offers superior quality bass reproduction when used with any digital audio system that incorporates bass management or programmable crossovers Auto turn on using trigger input or
20. l Range Front Front Input on the SUB TS18 subwoofer Left Right Use both the left and right inputs on the A D g subwoofer if your receiver or processor has B SUB LFE 0 both left and right line level outputs In that e Out case you will need to supply a second Surround Surround interconnect cable En Pee aoe If your receiver is equipped with line level out o a Ay 1 l QO Surround puts but does not have a separate subwoofer Right output use a Y adapter not supplied to bridge the receiver s preamp output to the Receiver main amp input for that channel and connect 5g the long end of the adapter to the corre sponding line level input on the SUB TS18 IMPORTANT Do not use the SUB Input on the subwoofer with Dolby Pro Logic processors If your receiver processor has a built in low pass crossover filter for the subwoofer out put you may use the SUB Input to bypass the subwoofer s internal crossover Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure that you have configured your surround sound processor for Subwoofer On The front left front right center and surround speakers should all be set to Small When all connections have been made plug the AC power cord on the subwoofer into an AC outlet SPEAKER CONNECTIONS 11 SPEAKER CONNECTIONS Dolby Pro Logic Non Digital Speaker Level USE THIS IN
21. let for proper operation of the SUB 1518 The cord should not be plugged into the accessory outlets found on some audio components SUB TS18 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS Color Coding System The HKTS 18 uses the channel color cod Ing system established by the Consumer Electronics Association to make setting up your home theater speaker system as easy as possible Your system includes a set of colored stickers that may be placed near the speaker terminals of each of the four Satellite speakers according to the chart below It doesn t matter which satellite speaker is used for any of the front or rear positions The center speaker and powered subwoofer are already color coded for you Speaker Sticker or Terminal Position and Cable Color Front Left White Front Right Red Center Green surround Left Blue surround Right Gray subwoofer LFE Purple Before you begin to connect cables it is important to set up your speakers in their correct locations in the room Optimally the speakers should be placed in a circle with the listening position at its cen ter The distance from the listening position to the video display forms the radius of the circle The speakers should be angled so that they directly face the listening position The cen ter speaker is placed either on top of or below the video display screen The front left and right speak
22. ntil the low frequencies sound best Place the subwoofer in that spot SPEAKER PLACEMENT MOUNTING OPTIONS Satellites and Surrounds Wall Mounting Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker otore the stand and bolt in a safe place in case they are needed for a future installation Wall Plate B l l l Remove Mount the wall Stand bracket attachment A plate on the wallin apaa D M6 1 25P the desired loca or 1 4 20 tion If possible position the speakers so that the mounting screws not included use size 8 may be installed directly into a wooden wall stud If that is not possible use optional wall anchors that are rated to support at least 25 pounds he customer is responsible for proper selection and use of mounting hard ware available through hardware stores to properly and safely wall mount the speakers Referring to the speaker connection instruc tions on pages 9 through 12 thread the appropriate speaker cable through the open ing in the bottom of the wall plate and then through the back of the bracket as shown in the diagram above The bracket has two 8 MOUNTING OPTIONS The satellite speakers may be placed on a shelf Place each satel lite soeaker on one of the supplied coasters for added stability and to protect your furniture The satellite soeakers may be wall mounted using the supplied brackets
23. r Switch AC Power Cord or DC is detected the SUB T518 amplifier will turn on even when the audio sense feature has been activated by placing the Audio Sense On Off Switch in the AUTO position The amplifier will remain on for about 10 15 minutes without a trigger signal Audio Sense On Off Switch When placed in the AUT O position and when the Master Power Switch is turned on the SUB 1518 will automatically turn itself on or SUB TS18 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS 5 6 SUB TS18 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS place itself in the Standby mode depending on whether it is receiving an audio signal When this switch is placed in the ON position the SUB 1S18 will remain on whether or not it is receiving an audio signal An LED located on top of the SUB 1S18 indicates whether the SUB TS18 is in the On or Standby state when used with the Audio Sense On Off Switch in the AUTO position The LED is lit blue to indicate that the SUB TS18 is receiving an audio signal and is turned on and the LED is lit amber to indicate that no signal is being received and the SUB TS18 is in the Standby mode When the Audio Sense On Off Switch is in the ON position the LED will be lit blue whether or not an audio signal is present When the Master Power Switch is turned off the LED goes dark no matter which position the Audio Sense On Off Switch is in Phase Switch
24. r touching other wires e In Dolby Digital or DTS mode make sure that the receiver processor is configured so that the speaker in question is enabled e Jurn off all electronics and switch the speaker in question with one of the other speakers that is working correctly Turn everything back on and determine whether the problem is in the same place i e the speaker that was working previously now has no sound and the speaker that was not working now sounds fine or whether it has moved i e the speaker that was not working still has no sound and the speaker that was working is still fine If the problem is in the same place the source of the problem is most likely with your receiver or amplifier and you should consult the owner s manual for that product for further information If the problem has followed the speaker consult your dealer for further assistance or if that is not possible visit our Web site at www harmankardon com for further information e Check all wires and connections between receiver amplifier and speaker Make sure all wires are connected Make sure none of the speaker wires are frayed cut punctured or touching other wires e f your receiver processor is set in Dolby Pro Logic mode make sure the center speaker is not in Phantom mode e f your receiver processor is set in Dolby Digital or DTS mode make sure the receiver processor is configured so that the center speaker is enabled e Check all wires and connections
25. res e Make sure the movie or TV show you are watching is recorded in a surround sound mode If it is not check to see whether your receiver processor has other surround modes you may use e In Dolby Digital or DTS mode make sure your receiver processor is configured so that the surround speakers are enabled e Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode and that you have properly selected that mode using both the DVD player s menu and the DVD disc s menu TROUT 6 Lie S cllQWOH LINE HKTS 18 System Frequency Response 25Hz 20kHz 6dB SAT TS18 Satellites Recommended Power 10 120 Watts Impedance 8 Ohms nominal Sensitivity 86dB 1 watt 1 meter Tweeter One 3 4 19mm dome video shielded Midrange Dual 3 75mm drivers video shielded Dimensions H x W x D 9 9 16 x 3 15 16 x 3 5 8 243mm x 100mm x 92mm Weight 2 8 b 1 3kg Care and Cleaning CEN TS18 Center Recommended Power 10 120 Watts Impedance 8 Ohms nominal Sensitivity 86dB 1 watt 1 meter Tweeter One 3 4 19mm dome video shielded Midrange Dual 3 75mm drivers video shielded Dimensions H x W x D 4 x 9 1 2 x 3 5 8 102mm x 241mm x 92mm Weight 2 7 b 1 2kg HKTS 18 SPECIFICATIONS SUB TS18 Subwoofer Amplifier 200 Watts RMS Bass 10 250mm Woofer bass reflex enclosur
26. rtion of the signal avoiding PANEL CONTROLS AND CONNECTIONS SUB TS18 issn harman kardon H A Harman International Company Northridge CA 91329 USA Made in China This area is designed to become quite warm during normal operation RISK OF ELECTRIC SHOCK A DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE D AVERTISSEMENT POUR PR VENIR LES RISQUES D INCENDIE OU DE CHOC ELECTRIQUE EVITER D EXPOSER CET APPAREIL A LA PLUIE OU A L HUMIDITE WARNING FOR CONTINUED PROTECTION AGAINST R ISK OF FIRE REPLACE ONLY WITH SAME TYPE T 3 15A L 250 VOLT FUSE AVERTISSEMENT UTILISEZ UN FUSIBLE DE RECHANGE DE MEME TYPE T 3 15A L 250V Q T3 15AL 250V Phase Switch Line Level Subwoofer SUB Input Line Level Full Range Inputs Speaker Level Outputs inefficiency and distortion Engage this filter when using the Speaker Level Inputs or when using the Line Level Full Range Inputs unless your receiver or processor processes its line level output using a low pass filter The filter has no effect when the SUB Input is used External Trigger Input Use the sup plied mini plug cable to connect the trigger Output of another product to this jack When a trigger signal between 3 and 30 volts AC Q AC 120V 60Hz 300 Watts POWER Speaker Level Inputs Master Powe
27. tion It is important to connect all speakers identically on the speaker to on the amplifier and on the speaker to on the ampli fier Wiring out of phase results in thin sound weak bass and a poor stereo image With the advent of multichannel surround sound systems connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material To connect the supplied speaker wires to the satellite and center speaker terminals located on the bottom of each speaker press the red or black tab insert the bare end of the wire into the hole and release the tab Gently tug on the wire to make sure that it is fully inserted For the best performance Harman Kardon recommends that the subwoofer be con nected using either the Line Level Subwoofer SUB Input or the Line Level Full Range Inputs However if the application requires the use of the speaker level connections for the subwoofer unscrew the binding post collar until the pass through hole in the center post is visi ble under the collar Insert the bare end of the wire through this hole then screw the collar down until the connection is tight The hole in the center of each collar is intended for use with banana type connectors SPEAKER CONNECTIONS 9 SPEAKER CONNECTIONS Dolby Digital or
28. tion Guide IMPORTANT NOTE Before making speaker connections be certain that your receiver or audio power amplifier is turned off and preferably unplugged from its AC power source The SUB 1S18 subwoofer should not be connected to an AC power source until all soeaker wire connections have been made Speakers and electronics terminals have corresponding and terminals Most manufacturers of speakers and electronics Including Harman Kardon use red to denote the terminal and black for the terminal Newer Harman Kardon receivers conform to the new CEA standard and therefore use a color other than red or black for the ter minal to indicate some speaker positions e g Surround left Although the HKTS 18 system has red and black collars on the individual speaker terminals to denote the positive and negative connections your system includes a colored band on the positive lead at both ends of every speaker cable and a matching colored sticker for each of the four satellite speakers conforming to the chart on page 7 The center speaker has a green terminal and the subwoofer SPEAKER CONNECTIONS has a purple SUB input jack This system is Intended to help you ensure that the speaker in each location is connected to the correct terminals on your receiver or amplifier The lead of the speaker wire is indicated with a stripe and has the colored band cor responding to the speaker s posi
Download Pdf Manuals
Related Search