LG Electronics iCAM4100 Digital Camera User Manual
Contents
1. 4100 1 Set the computer to the static IP of 192 168 5 1 subnet 255 255 255 0 2 Open the web browser and enter http 192 168 5 100 in the address bar then press ENTER The iCAM login screen will appear 3 Enter the default Username iCAM4000 and Password iris4000 both are case sensitive lrisAccess iCAM 4000 4100 Configuration E Administrator Login version 2 02 copyright 2007 LG Electresics USA Inc Iris Technology Ovvisien All righas reserved 4 The iCAM Configuration Main Menu will appear ic Kaa ni tae aly Meter iCAM 4000 4100 Configuration lrisAccess Change Username Password Configuration Settings SmartCard Configuration Network Settings ICAM Software Update iCam WwebConfig Update Voice Message Update Reboot version 3 03 O Copright 200 LO Ehectrosics USA Inc Iris Technology Ovvigiea All rights reserved 8 iCAM4100 Configuration cont d 5 Select Network Settings lrisAccess iCAM 4000 4100 Configuration E Network Settings IP Address 192 168 5 100 Subnet Mask 255 255 255 Broadcast Address 192 1 Oefaut Gateway x Ces Back to Main Enter the new IP address for the iCAM default 192 168 5 100 Enter the new Subnet Mask for the iCAM default 255 255 255 0 Enter the new Broadcast Address for the iCAM default 192 168 5 255 Enter the new Default Gateway for the iCAM default 192 168 5 254 0 C2. Technical Support Additional information and Technical assistance is available on the LG Electronics Iris Technology Division s support web site at www lgiris com click on Support amp Service then Technical Support
3. system component on the Ethernet network system must have a unique manually assigned IP address The iCAM4100 requires at least the following wires e Ethernet network wiring to connect with the network switch to communicate to the IrisServer or an ICU Note For systems consisting of only an IrisServer and iCAM may use an Ethernet crossover cable to connect the iCAM directly to the IrisServer computer e Power 12VDC 10 and 2 5Amps MAX IMPORTANT IT IS RECOMMENDED TO USE THE POWER ADAPTER SUPPLIED WITH THIS PRODUCT AN OVER OR UNDER VOLTAGE APPLIED TO THIS PRODUCT MAY CAUSE PERMANENT DAMAGE AND VOID THE WARRANTY 4 iCAM4100 Installation 1 Remove the three security screws use included security bit wrench from the bottom of the iCAM Front Back U 2 While gently pulling the cover upward pull forward simultaneously 3 4 5 Unscrew the installation plate screw and slide the body of iCAM4100 upward to separate from the installation plate Position the installation plate on the desired wall near the secured door and mark the holes as the figure below illustrates The recommended height from the floor to bottom of unit is 140cm 55 however installation height can be adjusted depending on average height of users In case of recessed mounting leave 6mm 1 4 of extra space above the marked hole when mounting the installation plate to allow the iCAM to slide down onto the install
4. 10 Connect the CAT5 RJ45 network wire into the LAN port of the iCAM Make sure that the RJ45 connector locks securely into the LAN port 11 Wiegand device such as proximity card reader and smart card readers may be connected to the iCAM through the Smart Card or Wiegand In connections Refer to the 4000 Hardware Manual for connection details Note Only the smart card serial and Wiegand input interfaces are active with the current iCAM versions Note The iCAM4110 H1 iCAM4111 H1 and the iCAM4110 E1 iCAM4111 E1 are supplied with a smart card reader already wired and installed 12 Close the front cover and gently slide the cover downwards Fasten with front cover using the three security screws Note The iCAM includes two tamper switches One switch is located on the rear of the iCAM to detect removal from the wall or enclosure from which it is installed A second tamper switch is located behind the front plate to detect tampering with the front of the unit During installation be sure that the rear tamper switch is in a position which can detect unit removal from the wall or enclosure iICAM4100 Configuration Changing the IP Address of the iCAM Note The IP Address of each iCAM must be changed individually Do not connect more than one un configured iCAM to the network at any one time to avoid IP Address conflicts Any computer with a web browser which supports graphics ex Internet Explorer can be used to configure the iCAM4000
5. ation plate tabs 5 iCAM4100 Installation cont d 208 196 6 4801 2 156 139 IN SS SSN OS S SASS __ H 5 H lt hole gt a j SS YZ A Dimensions and Screw Holes in the Installation Plate mm unit Rotation Part with Front Enclosure Installation Plate Dimensions of iCAM4100 mm unit iICAM4100 Installation cont d Route the power line network line and other necessary cables through the installation plate hole Using the appropriate fasteners for the material in which the iCAM will be mounted secure the installation plate Slide the iCAM4100 body into the installation plate and fasten it with the retaining screw Oe J09 am Attach the wires from the 12VDC power supply to the screw terminal connections The 12VDC white wire power connects to the positive terminal whereas the 12VDC ground black wire connects to the negative terminal Note If it is required to extend the length of the wires from the power adapter to the iCAM refer to the www lgiris com support web site for details Wiegand IN Wiegand OUT Serial RS 232 422 485 Power Input GND VCC Unused O General SmartCard Purpose I O Ljpaeeones Reader Keypad Input Tamper SW
6. lick OK to save changes and to open network settings verify screen Se eS If the new iCAM IP address is still on the same subnet as the computer after 10 seconds the web browser will resolve to the new IP address and the login screen will appear again If the new iCAM IP Address is on a different subnet the web browser will display the standard The page cannot be displayed message To test the IP Address change perform a ping to the new IP Address Click on Start in the Windows task bar Select Run Type cmd Press Enter At the command prompt type ping lt new IP gt ex ping 192 168 5 120 Close the command prompt window OF OT NS a If changing the IP Address to multiple iCAMs Note After each iCAM configuration the arp cache on the computer must be deleted Click on Start in the Windows task bar Select Run Type cmd Press Enter At the command prompt type arp d Close the command prompt window Connect the next iCAM to be configured on the network and perform the configuration to the next iCAM PICO sent D a 9 iCAM4100 Configuration cont d Once all iCAMs have been configured Once all iCAMs have been configured the computer IP Address can then be changed back to its original IP Address or to the new IP Address as required to communicate to the rest of the IrisAccess system SmartCard Integration e The iCAM4010 E1 and iCAM4010R E1 have a built in Integrated Engineering Smart ID smar
7. lrisAccess LG Advanced Identity Authentication Advanced Identity Authentication ICAM 4100 Quick Start Guide FOR MODEL NUMBERS iCAM4100 iCAM4100R iCAM4101 iCAM4101R iCAM4110 E1 OO000 ees O O O O iCAM4110 H1 iCAM4110R H1 OOOO iCAM4111 E1 OOOO iCAM4111R E1 O f iCAM4111 H1 InisAccess iCAM4111R H1 COPYRIGHT 2007 LG ELECTRONICS USA INC ALL RIGHTS RESERVED LG IrisAccess 4000 iCAM4100 Quick Start Guide The content of this document is furnished for informational use only is subject to change without notice and should not be construed as a commitment by LG Electronics USA Incorporated LG Electronics USA Incorporated assumes no responsibility of liability for any errors or inaccuracies that may appear in the informational coritent contained in this document Please remember that existing images or drawings that you may want to include in your document may be protected under copyright law The unauthorized incorporation of such material into your work could be a violation of the rights of the copyright owner Please be sure to obtain any permission required from the copyright owner LG LG Iris the LG logo LG Iris logo and IrisAccess are either registered trademarks or trademarks of LG Electronics Incorporated in the United States and or other countries LG Electronics USA Incorporated Iris Technology Division 7 Clarke Drive Cranbury New Jersey 08512 USA Documen
8. t Number DV002Q502 07 07 1 Packing List What s in the box e jCAM4100 IrisCamera e Power Adapter Input 110 240V AC 1 5AMP 50 60Hz Output 12V DC 5 0AMP e Power Cable for 110V e CAT5 Ethernet Cable e Quick Start Guide e Security Screw Wrench Required Equipment not included with iCAM4100 e Server Computer refer to the Hardware Manual for details e Ethernet Switch e Ethernet Wiring e Uninterruptible Power Supply 2 iCAM4100 in the IrisAccess System iCAM4000 4100 Network Switch Ethernet Poeeneennedy Door Control rea ee RS 422 Serial cea 3s The iCAM4100 is a two eye iris camera used to capture the iris images of the user The iCAM includes an alignment indicator behind the mirror and voice prompts to assist the user A Vacuum Fluorescent Display VFD displays system time date and user guidance When used in a typical access control application the iCAM is placed near the secured portal to provide user identification The optional keypad can be used for a PIN verification mode The iCAM can be used in enrollment mode using the IrisEnroll application included with EAC software or recognition mode when it is configured for use with an ICU The iCAM can not easily be switched between enrollment and recogni
9. t card reader and the iCAM4010 H1 and iCAM4010R H1 have a built in HID iClass smart card reader e The only configuration to the iCAM for smart card support is to enter an Air link Encryption key or Application key This key is used to lock unlock access to the smart card data Once changed the iCAM will write all cards with this key enrollment and will only be able to read cards with this key verification e To configure the smart card key log into the iCAM configuration interface see Changing the IP Address of the iCAM in section 6 e From the main menu select SmartCard Configuration lrisAccess iCAM 4000 4100 Configuration E SmartCard Configuration Serial Port SmartCard Type HID iCless z Applicat On Key fessssssessssosse Set t Odak hexadeamal ox Cier Back to Main e Leave the Serial Port selection as Serial Port 2 e Select the Smart Card Type HID iClass iCAM4010 H1 MIFARE or Smart ID iCAM4010 E1 e Enter the Application Key Air Link Key in Hexadecimal format Note Set to Default will reset the Application Key to the HID iClass default e OK must be clicked for the changes to be entered e To complete the smart card integration in the IrisAccess system the IrisServer IrisEnroll software and ICUs must be configured Refer to the 4000 Smart Card Integration document located on the EAC software CD for more information 10 Technical Support
10. tion modes once configured The iCAM can be wall mounted or used with an optional desk top stand iCAM4100 Model Variations Smartcard Reader VFD RoHS compliant Keypad HID iClass IE Smart ID iCAM4100 iCAM4100R e iCAM4101 e iCAM4101R e iCAM4110 H1 iCAM4110R H1 e e iCAM4110 E1 iCAM4110R E1 d o iCAM4111 H1 e 9 iCAM4111R H1 e iCAM4111 E1 hd o hd iCAM4111R E1 o o 3 Installation Requirements bottom of mirror aut ils ris punt x at CG pt AE 61 155mm 55 140mm floor e The recommended mounting height for the iCAM4100 is 140cm 55 inches from the floor to the bottom of the unit This mounting height can be adjusted to accommodate the average user height at the installed location e High amounts of ambient light must be avoided Intense light sources such as sunlight or halogen lamps may reduce the image capture performance of the iCAM this may result in an increased failure to acquire rate e The iCAM is not weatherproof and must not be exposed to precipitation or extreme temperatures An enclosure may be used to protect the unit if required See www lgiris com Support amp Service for more information e All system components including the Ethernet network must be powered through Uninterruptible Power Supplies UPS UPS must provide power line filtering as well as power back up operation e Each IrisAccess
Download Pdf Manuals
Related Search