Lexmark 2400 Printer User Manual
Contents
1. 18 Shipping the printer 18 Contents 2 Maintaining the printer Periodically certain tasks are required to maintain optimum print quality Cleaning the exterior of the printer 1 Make sure that the printer is turned off and unplugged from the wall outlet CAUTION SHOCK HAZARD To avoid the risk of electric shock when cleaning the exterior of the printer unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding 2 Remove paper from the standard exit bin 3 Dampen a clean lint free cloth with water Warning Potential Damage Do not use household cleaners or detergents as they may damage the finish of the printer 4 Wipe only the outside of the printer making sure to include the standard exit bin Warning Potential Damage Using a damp cloth to clean the interior may cause damage to your printer 5 Make sure the paper support and standard exit bin are dry before beginning a new print job Cleaning the printhead lenses Clean the printhead lenses when you encounter print quality problems 1 Open the front door Maintaining the printer 3 Warning Potential Damage To avoid overexposing the photoconductor units do not leave the front door o2. 6 Ordering a fuser or a transfer module 6 Ordering a waste toner box 7 Replacing Supplies 8 Replacing a photoconductor 8 Replacing a toner cartridge 11 Replacing the waste toner box 15 Moving the printer 16 Before moving the printer 16 Moving the printer to another location 17 Setting the printer up in a new location
3. 3 Press the release button to the left and pull the waste toner box out to remove it from the printer 4 Peel the seal from the side of the full waste toner box as shown and then place it over the hole to seal off the waste toner box 5 Place the sealed waste toner box in the recycling bag Maintaining the printer 15 6 Place the bag into the shipping box you just removed the replacement part from 7 Peel the recycling label off and place it on the shipping box 8 Insert the new waste toner box into the printer Moving the printer Before moving the printer CAUTION POTENTIAL INJURY The printer weight is greater than 18 kg 40 lb and requires two or more trained personnel to lift it safely Maintaining the printer 16 Follow these guidelines to avoid personal injury or printer damage Always use at least two people to lift the printer Always turn off the printer using the power switch before moving it Disconnect all cords and cables from the printer before moving it Remove the printer from the options before moving it Warning Potential Damage Damage to the printer caused by improper moving is not covered by the printer warranty Moving the printer to another location The printer and options can be safely moved to another location by following these precautions Remove the printer from the options before moving it Any cart used to move the printer must have a surface able to supp
4. Multi Pack C734X24G Ordering a fuser or a transfer module When 80 Fuser Life Warning or 83 Transfer Module Life Warning appears order a replacement fuser or a transfer module Maintaining the printer 6 When 80 Replace Fuser or 83 Replace Transfer Module appears install the new fuser or the new transfer module For installation information see the documentation that came with the part Part name Part number Fuser 40X5095 100 volt 40X5093 115 volt 40X5094 230 volt Transfer Module 40X5096 Ordering a waste toner box When 82 Waste toner box nearly full appears order a replacement waste toner box When 82 Replace waste toner box appears you must replace the waste toner box Note Waste toner box reuse is not recommended Part name Part number Waste Toner Box C734X77G Maintaining the printer 7 Replacing Supplies Replacing a photoconductor There are three different display messages which may appear when a photoconductor replacement is necessary 84 Replace lt color gt photoconductor 84 lt color gt photoconductor nearly low or 84 lt color gt photoconductor low Note A replacement photoconductor can be used with any color Replacing a photoconductor is a two part process First complete the illustrated steps to replace the photoconductor and then reset the life count and clear printer messages 1 Open the front door Warning Potential Damage To avoid overexposing the photocon
5. C734 and C736 Series Maintenance Guide May 2009 www lexmark com Contents Maintaining the printer 3 Cleaning the exterior of the printer 3 Cleaning the printhead lenses 3 Storing supplies 5 Checking the status of supplies 5 Checking the status of supplies from the printer control panel 5 Checking the status of supplies from a network computer 6 Ordering supplies 6 Ordering toner cartridges 6 Ordering photoconductors
6. ck a new cartridge 7 Place the old cartridge in the replacement cartridge shipping box and then attach the return label to the box for shipping 8 Shake the new cartridge front to back and side to side to evenly distribute the toner Maintaining the printer 13 9 Remove the red packing strips from the new cartridge 10 Insert the new cartridge into the printer 11 Close the front door Note Make sure each cartridge is fully pushed in If a cartridge is not installed correctly the printer may issue a lt color gt Cartridge Missing message where lt color gt is Black Cyan Magenta or Yellow The printer may also issue the message Close front door If either of these messages appears follow the steps below to clear the printer control panel message and continue printing 1 Open the front door 2 Remove the specified cartridge Maintaining the printer 14 3 Reinstall the specified cartridge 4 Close the front door 5 Check the printer control panel to see if it is clear of messages 6 Repeat as needed for additional toner cartridge replacement Replacing the waste toner box Replace the waste toner box when 82 Replace waste toner box or 82 Waste toner box nearly full appears The printer will not continue printing until the waste toner box is replaced 1 Unpack the replacement waste toner box and remove it from its shipping box 2 Locate the waste toner box release button on the left side of the printer
7. ductors do not leave the door open for more than 10 minutes 2 Pull the specified photoconductor up and then slide it to the right to remove it from the printer Maintaining the printer 8 3 Unpack the replacement photoconductor 4 Align and insert the left end of the photoconductor and then snap the right end into place 5 Remove the red packing strip from the top of the photoconductor Maintaining the printer 9 6 Place the old photoconductor into the replacement photoconductor box and then place the return label on the box for shipping to Lexmark for recycling 7 Close the front door 8 If you see 84 Replace lt color gt photoconductor 84 lt color gt photoconductor nearly low or 84 lt color gt photoconductor low on the printer control panel press the down arrow button until Supply Replaced appears and then press Note Failure to reset the life count may result in degraded print quality Replaced lt color gt photoconductor appears Yes appears 9 Press to clear the message If you are prompted to replace only one photoconductor then the Ready screen will appear and the task is complete If you are prompted to replace additional photoconductors repeat Steps 8 and 9 for each additional photoconductor After all photoconductors have been replaced Ready appears and the task is complete Maintaining the printer 10 If you see Ready on the printer display screen after you have replaced a phot
8. e 192 264 263 17 3 Press Enter The Device Status Page appears A summary of supply levels is displayed Ordering supplies To order supplies in the U S contact Lexmark at 1 800 539 6275 for information about Lexmark authorized supplies dealers in your area In other countries or regions visit the Lexmark Web Site at www lexmark com or contact the place where you purchased the printer Note All life estimates for printer supplies assume printing on letter or A4 size plain paper Ordering toner cartridges When 88 Cyan cartridge low 88 Magenta cartridge low 88 Yellow cartridge low or 88 Black cartridge low appears order a new cartridge When 88 Replace Cyan cartridge 88 Replace Magenta cartridge 88 Replace Yellow cartridge or 88 Replace Black cartridge appears you must replace the specified cartridge Estimated cartridge yield is based on the ISO IEC 19798 standard with about 5 coverage per color Extremely low print coverage less than 1 25 for a color for extended periods of time may negatively affect actual yield for that color and may cause cartridge parts to fail prior to exhaustion of toner Ordering photoconductors When 84 photoconductor low or 84 lt color gt photoconductor nearly low appears order a replacement photoconductor When 84 Replace lt color gt photoconductor appears you must replace the specified photoconductor Part name Part number Photoconductor C734X20G Photoconductor
9. oconductor follow Steps 1 through 7 below 1 To specify the replaced photoconductor press Supplies Menu appears 2 Press Replace Supply appears 3 Press 4 Press the down arrow button until All Cyan photoconductor Magenta photoconductor Yellow photoconductor or Black photoconductor appears depending on the photoconductor you just replaced 5 Press lt color gt photoconductor replaced appears Yes appears 6 Press 7 Press until Ready appears The task is complete Replacing a toner cartridge When 88 Replace lt color gt cartridge 88 lt color gt cartridge nearly low or 88 lt color gt cartridge low appears on the printer control panel or when print becomes faded try to extend the life of the specified cartridge 1 Open the front door Warning Potential Damage Make sure the printer is not open for 10 minutes or more to avoid overexposing the photoconductor units to light Maintaining the printer 11 2 Pull up and out on the green tabs of the specified cartridge to remove it from the printer 3 Shake the cartridge front to back and side to side to redistribute the toner 4 Reinsert the cartridge to continue printing 5 Repeat this process multiple times until printed text and graphics remain faded When printed text and graphics remain faded replace the specified cartridge Repeat steps 1 and 2 and then follow the steps below Maintaining the printer 12 6 Unpa
10. ort the full footprint of the printer Any cart used to move the options must have a surface able to support the dimensions of the options Keep the printer in an upright position Avoid severe jarring movements Maintaining the printer 17 Setting the printer up in a new location When the printer is set up allow clearance around it as shown 1 152 4 mm 6 0 in 2 101 6 mm 4 0 in 3 609 6 mm 24 0 in 4 101 6 mm 4 0 in 5 304 8 mm 12 0 in Shipping the printer When shipping the printer use the original packaging or call the place of purchase for a relocation kit Maintaining the printer 18
11. pen for more than 10 minutes 2 Remove all four toner cartridges Do not remove the photoconductor units for this procedure 3 Locate the four printhead lenses 4 Clean the lenses using a can of compressed air Warning Potential Damage Do not touch the printhead lenses 5 Reinstall the four toner cartridges Maintaining the printer 4 6 Close the front door Storing supplies Choose a cool clean storage area for the printer supplies Store supplies right side up in their original packing until you are ready to use them Do not expose supplies to Direct sunlight Temperatures above 35 C 95 F High humidity above 80 Salty air Corrosive gases Heavy dust Checking the status of supplies A message appears on the display when a replacement supply item is needed or when maintenance is required Checking the status of supplies from the printer control panel 1 Make sure the printer is on and Ready appears 2 From the printer control panel press the down arrow button until Status Supplies appears and then press 3 Press the down arrow button until View supplies appears and then press The status of each supply appears Maintaining the printer 5 Checking the status of supplies from a network computer Note The computer must be connected to the same network as the printer 1 Open a Web browser 2 In the address bar type the IP address of the network printer for exampl
Download Pdf Manuals
Related Search