Leviton 61110-Rx6 Switch User Manual
Contents
1. i Replace front face and wallplate Programming is complete 5 Set applicable Receiver code to correspond with the code of this Transmitter or code of suitable desired row refer to Receiver Program Instructions SCENE PROGRAMMING Cat No HCCS7 ONLY NOTE Scenes may be set for devices set to the same code as transmitter and additional sequential 11 unit code i e code set to A1 will permit scenes on devices to be set to A1 A12 If code 16 is reached before 12 sequential codes it will start with 1 2 3 i e code set to A15 cycling sequence is A15 A16 A1 A10 NOTE Scenes sent to all 16 codes simultaneously can only have 12 sequential addresses programmed unprogrammed 1 Press and hold the scene button you would like to program for approximately 5 seconds All LED s will flash except for selected scene button You are now in the programming mode 2 At each local dimmer Cat No HCM10 or HCMO06 or switch Cat No HCS10 non dimmable adjust lights to the desired level 3 Press the selected scene button on the HCCS7 The LED next to the scene button will flash for approximately 5 seconds then stay ON The scene is now programmed NOTE To erase a selected scene from the 12 sequential codes in memory press the OFF button while in the Scene Programming mode 4 Repeat steps 1 through 3 to program each additional scene until all of the scenes are set 5 Press the SCENE BUTTON once to send the scene command to all units o2. BLACK buttons with a protruding plastic LED to its left The left hand row of four buttons is used to set the Unit Codes numbers 1 16 The right hand row of four buttons is used to set the House Codes letters A P c Press the recessed PROGRAM BUTTON once The LED s will flash approximately every 2 to 5 seconds d To set Unit Code Determine code setting required i e L7 Unit Code is 7 Using matrix chart refer to Indicator Position Diagram determine which switches should be turned ON Press the switch next to corresponding LED position to turn that LED ON i e 7 press switches 2 and3 down from top to turn ON LED s next to them will illuminate and not flash e To set House Code Determine code setting required i e L7 House Code is L Using matrix chart refer to Indicator Position Diagram determine which switches should be turned ON press switch next to corresponding LED position to turn that LED ON i e 7 press switches 1 top right 2 and 4 down from top to turn ON LED s next to them will illuminate and not flash f Press PROGRAM BUTTON again LED s will stop flashing Unit is now programmed to L7 g To change or check set codes press PROGRAM BUTTON again LED s will illuminate corresponding last set code Repeat steps D through F if change is desired NOTE Ensure that the PROGRAM BUTTON is pressed again after checking or changing programming to ensure unit is in operating mode
3. bottom row OFF button will transmit the ALL ON ALL OFF commands for all devices set to the same letter code i e A To adjust brightness level of LAST selected address use DIM and BRIGHT arrows When transmitting an ON ALL ON command the LED will blink while the signal is being transmitted and will stay ON when the signal has completed the transmission When transmitting an OFF ALL OFF command the LED will blink while the signal is being transmitted and turn OFF when the signal has completed the transmission Pressing the BRIGHT or DIM button will cause the LED s on the face of the keypad to flash and will remain flashing until the button is released NOTE When used with a 2 Way Receivers the LED s will indicate the status of those devices i e if the Dimmer Switch is turned ON at it s source the ON OFF LED who s address corresponds to that device will turn ON OFF to match TO OPERATE Cat Nos HCCS7 ONLY Pressing the scene button will transmit a SCENE ON command Pressing another scene button will change the lighting to that programmed scene Pressing the OFF button will turn OFF the last selected scene To adjust brightness level of last selected address use DIM and BRIGHT arrows When transmitting a SCENE ON command the LED will blink while the signal is being transmitted and will stay ON when the signal has completed the transmission When transmitting an OFF command the LED will blink while the signal is being transmitted and
4. turn OFF when the signal has completed the transmission When the DIM or BRIGHT arrow is pressed all LED s will flash until the button is released NOTE When used with a 2 Way Receivers the Scene Dimmer will only indicate status when all devices are OFF TESTING Press the keypad to confirm that the load or loads are turned ON and OFF within two seconds of signal transmission If the Cat No HCCxx Controller appears to be functioning improperly or operates erratically read the following paragraphs then refer to the Perfect Performance Checklist The HCCxx series can switch multiple addresses from the same Controller The top button transmits as per the letter number code set on the Controller The next button down transmits to the same letter next number address as set on the Controller and so on Examples 1 ACat No HCC4A set at A3 top button controls the A3 address the next button down controls the A4 address and so on 2 A Cat No HCC4A set at B15 top button controls the B15 address the next button down controls the B16 address the next button down controls the B1 address and the last button controls the B2 address An ALL ON OFF button controls ALL DHC modules set to the same letter code as on the Cat No HCCxx Controller ALL ON only turns ON lighting modules ALL OFF turns OFF ALL modules set to the same letter code PK 93028 10 00 0B PERFECT PERFORMANCE CHECKLIST If the Cat No HCCxx Controller appears to be funct
5. Figure 2 If using a Decora Plus Screwless wallplate leave tabs intact 4 Connect wires per WIRING DIAGRAM as follows BLACK Hot wire to BLACK lead of device and WHITE Neutral to White lead of device Twist strands of each lead tightly together and with circuit conductor push firmly into appropriate wire connector Screw connector on clockwise making sure that no bare wire shows below the connector Secure each wire connector with electrical tape Mount Cat No HCCxx in wall box using the screws provided NOTE Ensure that the PROGRAM BUTTON is located at the bottom of the device when mounting refer to Indicator Position Diagram Remove Front Face of Cat No HCCxx refer to Color Conversion Procedure to access controls for programming Restore power at circuit breaker or fuse Set the address using the ADDRESS PROGRAMMING sequence below Replace Front Face see Color Conversion Procedure Attach the supplied programming instruction and code table labels to back of wallplate Replace wallplate INSTALLATION IS COMPLETE m opaap ADDRESS PROGRAMMING The system communicates via a preset code set on transmitters this device and receivers dimmers and switches The code consists of a letter code A B C P and a number code 1 2 3 16 refer to Indicator Position Diagram The unit must be set programmed to allow it to communicate with devices in the Home Control System This is accomplish
6. Home Controls re Decora Cat No HCCS7 WALL MOUNTED CONTROLLER w Multiple Addressing Cat Nos HCC2D HCC3D HCC4A HCC4D HCCS7 Rated 120VAC 60 Hz INSTALLATION INSTRUCTIONS Building A Connected World PK 93028 10 00 0B LIMITED TWO YEAR WARRANTY AND EXCLUSIONS Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date Leviton s only obligation is to correct such defects by repair or replacement at its option if within such two year period the product is returned prepaid with proof of purchase date and a description of the problem to Leviton Manufacturing Co Inc Att Quality Assurance Department 59 25 Little Neck Parkway Little Neck New York 11362 2591 This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation This warranty is void if this product is installed improperly or in an improper environment overloaded misused opened abused or altered in any manner or is not used under normal operating conditions or not in accordance with any labels or instructions There are no other or implied warranties of any kind including merchantability and fitness of a particular purpose but if any implied warranty is required by the applicable jurisdiction the duration
7. addresses in sequence plus DIM BRIGHTEN of each address 6 buttons HCC3D ON OFF for 3 addresses in sequence plus DIM BRIGHTEN of each address 8 buttons HCC4A ON OFF for 3 addresses in sequence plus DIM BRIGHTEN of each address and ALL ON OFF control of addresses within the same letter code 10 buttons HCC4D ON OFF for 4 addresses in sequence plus DIM BRIGHTEN of each address 10 buttons HCCS7 7 scenes plus DIM BRIGHTEN on 12 sequential pre selected addresses NOTE Cat No HCCxx Wall Mounted Controller is not intended to replace standard wall switches The Controller requires one HOT BLACK and one NEUTRAL WHITE conductor for proper operation Incorrect installation will void warranty INSTALLATION INSTRUCTIONS WARNING TO BE INSTALLED AND OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS WARNING IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS CONSULT A QUALIFIED ELECTRICIAN WARNING INSTALL TO CONTROL SCENE DIMMERS AND APPLICABLE DHC RECEIVERS ONLY DO NOT INSTALL TO CONTROL ANY LOAD DIRECTLY CAUTION USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE WITH ALUMINUM WIRE USE ONLY DEVICES MARKED CO ALR OR CU AL TO INSTALL WARNING TO AVOID FIRE SHOCK OR DEATH TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING 2 Remove approximately 3 4 1 9 cm of insulation from circuit conductors 3 If using a standard Decora wallplate remove A tabs from strap refer
8. ed by setting the controller s transmit code to correspond with dimmers and switches in the system it is installed in Program as follows 1 Determine what switches and dimmers you want to control 2 The HCCxx multi button controller will control devices set to the same code as itself The first most upper ON OFF buttons will control a device set to its code i e A5 The next lower row and consecutive row of buttons will control devices with sequential code settings i e 1 row A5 device code 2 row AB 3 and 4 row if equipped A7 and A8 Leviton Residential Powerline Carrier Components are designed to provide the greatest signal integrity and noise immunity possible However in some environments intense electrical noise can cause interference Figure 1 Intellisense AGC Signal Window Signal Window Receiver sensitivity with Intellisense gated AGC iN alll Ll Command Signal Gated AGC ignores Noise is not is picked up High noise levels picked up outside signal window Figure 2 Control Functions Cat No HCC4D depicted Address Control Buttons Group DIM BRIGHTEN Button Button Figure 3 Switch Plate Removal Color Conversion and Programming Push in 2 Locations 3 To set the code on the controller perform the following refer to Indicator Position Diagram a Remove wallplate and front face of device refer to Color Conversion Procedure b You will see rows of
9. entrance panel using a Leviton Repeater Coupler C If the Yellow ERROR CONDITION indicator is lit there is electrical noise present on the AC line which is interfering with proper module operation The source of the noise must be identified and either filtered out or eliminated See Technical Manual Confirm that you have a recent version of the DHC System Coupler Repeater To do this follow steps 1 3 in the Scene Programming section If the LED s continue to flash after a scene button is pressed in step 3 you must upgrade your DHC System A Repeater Coupler is recommended in all DHC systems for maximum signal The Leviton Technical Manual covers common DHC problems and system issues in more detail Indicator Position Diagram L7 Address Programming Shown Unit Code Settings number INDICATES LED ON Oe80e80C e House Code Settings letter INDICATES LED ON Oe8080C e OINDICATES LED OFF o eoeoeoe OINDICATES LED OFF oe o 0o00 O0e e 00 ecoc eocee O0e e 00 e000 0o00 e0000 0000 ooo eee OO00000 1234 5 6 CO eeeee00 O e o0o00060 0 8 g O e o0o0000 0 3 900000 10 11 12 13 14 15 16 ABCDEF oeoo 000o HIJK MNOP LED s Row not used for Programmin s 7 Address Programming Buttons Program Button Cat No HCCxx Wiring Diagram Controller Hot Black Line 120VAC 60Hz Neutral White Cat No HCC4D
10. ioning improperly proceed with the following steps 1 ga a E a Confirm that the Controller is wired exactly as shown in the wiring diagram Confirm that the receiver module is being supplied from a 120V 60Hz AC source ONLY Confirm that the load being controlled is in proper working order Local switch ON check for burned out bulbs etc Confirm that the Controller is powered and is set to transmit commands to the same letter and number code as on receiver modules Confirm that the Cat No HCCxx keypad is installed properly NOTE If the Controller still does not operate properly after following steps 1 5 proceed with diagnostic steps 6 and 7 Set the Controller to transmit address P1 Using a Cat No 6386 Signal Strength Indicator plugged in on the same branch circuit as the Controller confirm that the Controller is transmitting a minimum reading of 2 volts of command signal at the HI RANGE setting If the signal strength is less than 2 volts have the Controller checked Check for adequate command signal at the Cat No HCCxx location as follows A Plug the Cat No 6385 Signal Test Transmitter into a receptacle on the same circuit breaker as the Controller B Using the Cat No 6386 Signal Strength Indicator at the HCCxx location check the command signal amplitude Signal strength must be 100mV minimum If there is less than 100mV of signal present it may be necessary to couple both legs of the 120 240 Volt power service at the
11. n the housecode COLOR CONVERSION PROCEDURE The color of this device can be changed to suit your interior design requirements Simply obtain a color conversion kit of the appropriate color from your Leviton distributor and proceed as follows please note that the wallplate must be removed 1 Select the color of the face you desire 2 The frame has snaps on its sides Using a small screwdriver gently remove the frame from the strap refer Figure 3 3 Take the new frame and position it properly to the strap Line up the plastic snaps with the square holes in the strap Insert the snaps on one side of the frame into the strap 4 Firmly press sideways and down to slip the other snaps into place The frame snaps in with a audible click Ensure that all four snaps are secure Replace Decora wallplate The color conversion is complete TO OPERATE Cat Nos HCC2D HCC3D HCC4A and HCC4D ONLY Pressing the top ON button will transmit an ON command for the preset address Pressing the top OFF button will transmit an OFF command for the preset address The next lower row of ON OFF buttons will perform ON OFF commands for the next sequential address of the one selected i e first row A1 second row A2 third row A3 The group DIM BRIGHT buttons arrows will DIM or BRIGHTEN the last selected address To DIM or BRIGHTEN another address press the ON button for the desired address and then use the group DIM BRIGHT control On the HCC4A the
12. of any such implied warranty including merchantability and fitness for a particular purpose is limited to two years Leviton is not liable for incidental indirect special or consequential damages including without limitation damage to or loss of use of any equipment lost sales or profits or delay or failure to perform this warranty obligation The remedies provided herein are the exclusive remedies under this warranty whether based on contract tort or otherwise For Technical Assistance Call 1 800 824 3005 www leviton com Building A Connected World PK 93028 10 00 0B FEATURES Leviton s Decora Style design Universal design works with 1 and 2 Way Receivers Memory retained after Power Interruption Color conversion available INTRODUCTION with the signal Leviton has developed hardware and techniques for overcoming this interference when properly applied LEVITON S DHC DEVICES FEATURE INTELLISENSE THE RIGHT TYPE OF AUTOMATIC GAIN CONTROL AGC Leviton DHC devices use Intellisense a special gated type of AGC to help eliminate noise problems refer Figure 1 This circuit feature is ideal for powerline carrier systems because it only operates during the signal window when receivers listen for command signals Noise levels in the signal window are never as high as they are during other portions of the AC power curve Therefore Leviton s Intellisense gated AGC will desensitize a receiver to noise signals with onl
13. r and stronger line signals without affecting signals simultaneously on the line from other transmitters The resulting performance reliability exceeds that of any other powerline carrier home automation product line available today FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio tv Technician for help SPECIFICATIONS Rating 120VAC 60Hz Max Controllers on 1 circuit 4 Power Consumption 3W HCCxx CONFIGURATIONS HCC2D ON OFF for 2
14. y a minimal reduction in command signal sensitivity The result Problems from noise interference are dramatically reduced without affecting overall system performance It is the responsibility of the specifier installer to test for signal strength and the presence of noise using Leviton test equipment Cat Nos 6385 Signal Test Transmitter and 6386 Signal Strength Indicator and to properly apply signal coupling and noise reduction equipment according to the guidelines provided in the Decora Home Controls DHC Technical Manual and the DHC Troubleshooting Guide Leviton specifically denies any warranty of performance stated or implied where electrical noise interference exists at the time of installation or subsequent to installation by the addition of noise producing devices or equipment or where these components have been installed for non residential applications Installation of a Repeater Coupler is recommended in all DHC systems DHC Components are for residential use only Installation for any other application voids any warranty stated or implied DESCRIPTION Wall box Transmitter The HCCxx is a signal transmitter that works in conjunction with DHC receivers The Wall Mounted DHC Transmitter is designed to provide manual control of loads from one or more locations in a home over standard 60Hz 120V wiring The HCCxx Transmitter incorporates Leviton s exclusive Intellisense Automatic Gain Control AGC circuitry to deliver cleare
Download Pdf Manuals
Related Search