Lantronix EDS16PS Server User Manual
Contents
1. BS anzar wwwlanzancom 15 Band mT Half Full Octave OptiE 1 Stereo Equalizer INTRODUCTION Congratulations on your purchase of a new Lanzar Opti signal processor Opti mobile electronics are some of the most advanced car audio products available These quality audio products are designed and engineered to afford you years of uncompromising musical service Lanzar has utilized the latest electronic technologies in order to deliver a superb listening experience The E 15 Equalizer offers the listener the ability to intensify the listening experience add realism to their mobile system overcome his or her vehicle s unique acoustic properties and tailoring the sound to their preference The E 15 was designed with the goal of achieving the finest music reproduction Although the way it sounds to you is the ultimate decision maker in how you set up your car audio system we suggest the use of a sound analyzer to give you exact audio measurements of your cars interior so that you can achieve precise equalizer settings Of course the E 15 can and should also be adjusted to your preference Finally a tip once you achieve the optimum settings for your system don t keep changing them to suit particular program material Also we suggest you write the settings down and keep this record in case they ever accidently get changed This could save hours in having to experiment all over again general features precauti2. IN or s an unaffected way uts are connected to your head units RCA outputs If your head unit has a fader that fades between two sets of RCA outputs make sure that th toward the set of RCA connectors that you are using If your can connect the E 15 to your head unit via a high S 60 or equivalent This separate component al Speaker wires from your head unit and the RCA cables from the E 15 while balancing the lt output and the equalizer s input ow level adapter for ows you to connect crossover Th1s line output level is unaffected by the fader control This indicator lights up when the internal power supply is activated and the unit is operational e head unit fader is turned radio has only speaker level Control Range Lee Frequency Response ts of your Signal to Noise Ratio A Wtd ing your Input Sensitivity Maximum Output Voltage Channel Separation Power Requirement example your Dimensions WxDxH inches millimeters 20Hz e 30Hz e 45Hz e 67Hz 100Hz e 150Hz e 200Hz 350Hz 500Hz 800Hz 1 1KHz e 2 2KHz 4 4KHz e 6 GKHz e 17 2KHz 12dB Boost Cut 10Hz 30KHz 100aB 80mv 2 0Volts for 400mv Output 7 0 Volts 65 dB 11 16 Volts DC negative ground 11 5 8 x 8 9 32 x 1 1 2 295 x 210 x 38 Lanzar strives to continually improve and refine its products as well as to design new models Therefore the product specifications and illustrations in this manual are subject to change without
3. notice Standard 4 Channel Output For standard 4 channel operation plug both the left and right RCA outputs from your head unit into the E 15 inputs The output power can be distributed to either the front or rear speakers by using the fader control With the fader is in the center detent position you will have balanced output between your front and rear channels Turning the fader to either the front or rear position results in increased signal strength to that particular side while decreasing signal strength to the other side System wiring to REMOTE OUTPUT from HEAD UNIT Head unit Stereo DVD Player Tape Deck etc TO OUTPUT OF HEAD UNIT mi ar ee a 666566666 66600666 to BATTERY to AMP REMOTE ON TO REAR AMPLIFIER TO FRONT AMPLIFIER REAR CHANNEL FRONT CHANNEL Speakers Speakers Dual E 15 2 2 Channel Output Using 4 RCA Inputs Two Model E 15s are required for this configuration For more exact control the E 15s can be configured into separate mono units with the outputs summing the signal into stereo If your head unit has two pairs of RCA outputs plug both of the left outputs into the E 15 s left inputs and both of the right outputs into the E 15 s right inputs Place both of the fader controls of the E 15 s into the center detent position System wiring Head unit Stereo DVD Player Tape Deck etc TO FRONT OUTPUT OF HEAD UN
4. reasonably high level 4 High squeal noise from speakers e Output levels NOT set correctly e EQUALIZER frequencies NOT set correctly e Check for shorts on the speaker leads e Check the red power wire It muse be connected directly to the battery e Check the system s ground point It muse make good contact with chassis ground bare metal e The radio and the EQUALIZER must be grounded at the same reference point e Check the red power wire It must be connected directly to the battery e Check the system s ground point It must make good contact with chassis ground bare metal e his is almost always caused by a poorly grounded RCA patch cord limited Warranty policy All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment Units purchased in the USA are warranted to be free of defects in material and workmanship for three 3 years from the date of purchase This warranty is limited to the original retail purchaser of the Signal Processor Should the unit fail due to a factory defect in material or workmanship your unit will be repaired or replaced at the sole discretion of Lanzar To obtain warranty service you must first call our Consumer Return Hotline number at 718 236 6948 to obtain a Return Authorization RA number This RA Number must appear on the outside of your package and on all paperwork relating to your return When returning the unit to us for warranty ser
5. you drill or cut any holes investigate your car s layout very carefully Take care when you work near the gas tank fuel lines hydraulic line and electrical wiring Do not operate the signal processor when it is unmounted Attach all audio system components securely within the automobile to prevent damage especially in an accident Do not mount this signal processor so that the wire connections are unprotected or in a pinched condition or likely to be damaged by nearby objects Be sure to select a location inside your vehicle which has adequate ventilation Before making or breaking power connections in your system disconnect the vehicle battery Confirm that your head unit or other equipment is turned off while connecting the input and output jacks TAPE IA AXES de Hp MG SAG HE Eve 8 be If you need to replace the power fuse only replace it with a fuse identical to that supplied with the system PLAM WASHER C Using a fuse of a different type or rating may result in damage to your system which isn t covered by the manufacturer s warranty 1 Suggested Tools and Other Parts f e In line fuse holder e Felt tip marking pen Electric drill with a Phillips head screwdriver bit e Crimping tool or needle nose pliers e Wire strippers measure and ruler e Orange wire 20 gauge or heavier Red and Black wire 18 gauge or heavier e RCA stereo audio cables quantity and length determined by ap
6. 400Hz 8800Hz 17200Hz Each rotary control permits the signal at that control s frequency to be either increased by turning clockwise or decrea turning cou control provides no increa There are separate level controls on the When instal Typically w System is at i on the E 15 amplifier whi The goal in desired listen This switch hen the head u s ideal volum accordingly to the adjustmen ing volume controls wheth passing signals through in The line inp outputs you a Pyramid head uni Connect these outputs to the appropriate inputs of your power amplifier s The front outputs he amplifier driving your front speakers the rear outputs for the rear amplifier connect to t Connect this output to another signal processor type device in your system such as a nter clockwise by up to 12 dB When set to the center detent positio ch will create se or decrease at that frequency E 15 for both the left and right channel o ling and first setting up the system set the output level controls to the center detent position for a starting point nit volume is set to approximately the 2 o clock position your e Set the head unit volume this way and then adjust the o achieve the ideal volume without over driving the inpu distortion sed by n the Full Octave utputs is to obtain the best signal to noise ratio while obtain er or not the E 15 is providing equalization
7. IT 6666628060 4696666 9 Tus F to BATTERY silage B F AMP 2 REMOTE ON RAKAA a 2666256555 i eee E ee L to GROUND Tes E TO REAR feng gaan amp OF HEAD UNIT Aue E mz pa apgog66 5 REMOTEON Seeaeesss TO REAR AMPLIFIER TO FRONT AMPLIFIER FRONT CHANNEL Speakers REAR CHANNEL _ Speakers System Wiring Dual E 15 2 2 Channel Output Using 2 RCA INPUTS MORTE or Two Model E 15s are required for this configuration If HEAD UNIT Head unit Stereo DVD Player Tape Deck etc your head unit has only one pair of RCA output jacks you can achieve the same result by using a pair of Y adapter cables Utilizing two E 15s permits the users to tailor 4 separate 15 band channels in full stereo When setting up your system we suggest the use of a sound analyzer to aid in obtaining exact measurements of your car s interior This permits precise equalizer settings TO OUTPUT OF HEAD UNIT 686666666 to addigi Y ADAPTER UAE CABLES to BATTERY to AMP REMOTE ON i to GROUND TO REAR AMPLIFIER to AMP REMOTE ON TO FRONT AMPLIFIER REAR CHANNEL _ Speakers FRONT CHANNEL Speakers EM 4 Channel Output Using Speaker Level Inputs If your radio does not have RCA outputs as is the case with most standard OEM radios you can u
8. This wire connects to your head units remote out or power antenna lead out This wire should supply 12 Volts DC any time the radio CD or cassette are playing This lead must also be connected to any other components in your system that utilize a remote turn on lead for powering up 4 Connect all line inputs and outputs using high quality RCA RCA cables 5 Recheck all connections before powering up 6 Set all level controls to their least sensitive positions and set all crossover controls switches etc to the desired frequency or position T Once the system is powered up set the volume control on the head unit to about the 2 o clock position and then set all the amplifiers level controls for maximum output level 8 Now you are ready to start equalizing your vehicle with the E 15 Noise chech and SYSTEM adjustment NOISE CHECK Check the entire audio system for noise before permanently securing the EQUALIZER mounting 1 Start the engine 2 Turn the audio system on 3 Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise If so turn both the audio system and the engine off Do not secure the EQUALIZER mounting screws Refer to the Trouble Shooting Guide at this manual 4 f the audio system does not have any noise securely tighten the EQUALIZER mounting screw and double check the wiring cables for safe placement SYSTEM ADJUSTMENT Preliminary Adjustments Pre setting the system pr
9. ons features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting general features 15 Band Equalizer Controls per Channel in 1 2 and Full Octave Steps Blue Light Illumination 12 dB Boost Cut at Each Frequency Setting Front Rear and Line Outputs Separate Front Rear and Line Output Level Controls Front Rear Fader Control Power LED Indicator EQ Bypass Switch Gold Plated Connectors and Terminals Precautions To prevent short circuits be sure to disconnect the negative battery ground lead before wiring the system up When you finish the installation be sure to make one more check to be sure everything is done correctly Reinstate all car parts that were removed Reconnect the negative battery ground lead features and specifications 1 Fader Control 2 Right and Left Channel Equalizer Controls 3 Right and Left Output Level Controls 4 EQ In Out Switch 5 Line Inputs 6 Front amp Rear Outputs 7 Line Outputs 8 Power Indicator This rotary controls the balance between the front and rear outputs This fader takes priority over the fader in your car stereo head unit The 15 band equalizer controls divide the frequency co 20Hz 30Hz 45Hz 67Hz 100Hz 150Hz features and specifications 200Hz 350Hz 500Hz 800Hz and at full Control Frequencies Half Octave ntrol range into 1 2 octave steps at Octave steps 1100Hz 2200Hz 4
10. ove limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state
11. ovides a necessary starting point for fine tuning the entire audio system to maximum performance NOTE DO NOT MOUNT EQUALIZER UNTIL THE FOLLOWING PROCEDURES HAVE BEEN COMPLETED 1 Preset each amplifier input gain adjustment at the amplifier to half of maximum 2 Before turning the audio system on preset adjust the front and rear output level controls as well as the right channel and left channel Equalizer Control points 3 Slowly turn the volume up and listen carefully for obvious trouble in sound distortion no sound no hiss total silence Turn the system off refer to Trouble Shooting Guide at this manual Caution DO NOT ROUTE AUDIO CABLES AND POWER CABLES TOGETHER THIS CAN CAUSE ENGINE NOISE IN YOUR AUDIO SYSTEM ALWAYS DISCONNECT THE SYSTEM FROM THE BATTERY BEFORE ATTEMPTING TO MAKE OR ALTER ANY CONNECTIONS THIS PRODUCT IS DESIRED FOR USE IN ANY 12 VOLTS NEGATIVE GROUND ELECTRICAL SYSTEM ONLY INSTALLING THIS PRODUCT IN ANY POSITIVE GROUND ELECTRICAL SYSTEM COULD SERIOUSLY DAMAGE THE AUDIO SYSTEM TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE 1 There is an audible distortion at a low volume level 2 Awhining sound can be heard through the speakers when the audio system is at low volume with the engine running The whining noise remains unchanged or seems to disappear when the volume level is increased 3 There is a motor boating type of sound when the engine is running and the audio system volume is set at a
12. plication e Solder less connectors or soldering gun with heat shrink tubing MOUNTING and installation Processor Installation 1 Find a suitable location in the vehicle to mount the processor The E 15 is a trunk mount unit and it should be installed in close proximity to your amplifier system You should pick a location that offers easy access to the unit for adjustment 2 Before starting disconnect the vehicle s negative battery ground to prevent short circuits Bolt the processor to the mounting surface making sure there is sufficient air flow around the installation 3 There are three power terminals on the E 15 e A red 18 gauge stranded or heavier and insulated wire should be connected to the terminal marked 12V Wire an in line fuse holder on this lead as it is the 12V DC wire for the system This wire should be attached to the switched side of the vehicle s ignition switch and should have power to it only when the vehicle is running or the switch has been turned to the accessory position A black stranded wire of at least 18 gauge should be connected to the terminal marked Ground This is the ground wire for the E 15 and should be attached to the same ground point with the amplifiers in the system Keeping this ground wire as short as possible improves the electrical circuit and keeps ground related noise problems to a minimum e An orange stranded wire of a least 20 gauge should be connected to the terminal marked Remote
13. se the speaker outputs from those head units to supply audio signal to the E 15 The radio and the E 15 can be connected together by using a high low level impedance adapter such as the Pyramid NS 60 or its equivalent The proper adapter is crucial to provide a match with the input of the E 15 which will help to insure low noise and the finest sound quality from the components System Wiring to TO RADIO REMOTE ee Me OUTPUT from AA HEAD 11 UNIT Head unit Stereo DVD Player Tape Deck etc a to HIGH LOW ADAPTER eT 08000650 to GROUND to AMP REMOTE ON TO REAR AMPLIFIER TO FRONT AMPLIFIER La REAR CHANNEL FRONT CHANNEL Speakers Speakers Mounting and Installation Your new Opti Series Octave Equalizer comes complete with all required mounting hardware Please read the Installation Precautions section below before installing your Lanzar Opti signal processor and then refer to the diagrams provided to connect power audio input and output connections according to your own system configuration requirements Precautions Mark the location for the mounting screw holes by Se the Equalizer where you wish to install it and use a scribe or one of the mounting screws inserted in each of the mounting holes to mark the mounting surface If the mounting surface is carpeted measure the hole centers and mark with a felt tip pen Before
14. vice it must be carefully packed and shipped prepaid to R A 4 Lanzar Service Center 1600 63rd Street Brooklyn NY 11204 www lanzar com Equalizer You must also include the following items with your return e of your sales receipt or other proof of purchase eA ae letter indicating the problem you are experiencing with the product e Include in your letter your return address daytime phone number and RA Number e Also include a check or money order for 20 00 for return shipping handling and insurance or provide your VISA MasterCard number with expiration date Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid This warranty will be considered void if the unit was tampered with improperly serviced or subject to misuse neglect or accidental damage All implied warranties of merchantability and fitness for a particular purpose are limited in duration to the length of the warranty Lanzar expressly disclaims any liability for incidental or consequential damages caused by product defects This warranty does not cover any expense incurred in the removal and or reinstallation of the Signal Processor Lanzar s total liability will not exceed the purchase price of the Signal Processor Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the ab
Download Pdf Manuals
Related Search