Krell Industries Audio + Video Standard Surround Preamp/Processor Stereo Amplifier User Manual
Contents
1. UA REE Audio Video Standard The Leader in Audio Engineering Su rrou nd Preamp Processor y Els nr weet me ee ys D E es A vos NA 2 3s s z ESSE S 2 dn TEC z d S EE gymeryd gy mi Audio Video Standard Surround Preamp Processor TM Bech E Er Ze Krell industries Inc 45 Connair Road Orange CT 06477 3650 USA TEL 203 799 9954 FAX 203 799 9796 E MAIL krell krellonline com WEB SITE www krellonline com 1998 by KRELL Industries Inc All rights reserved CONTENTS INTRODUCTION 3 UNPACKING 3 PLACEMENT FRONT PANEL DESCRIPTION 5 BACK PANEL DESCRIPTION 9 CONNECTING THE AUDIO VIDEO STANDARD TO YOUR SYSTEM 12 REMOTE CONTROL DESCRIPTION 13 SYSTEM CONFIGURATION 18 OPERATION 26 SAVING RECALLING AND CLEARING CONFIGURATION SETTINGS 29 WARRANTY 30 RETURN AUTHORIZATION PROCEDURE 31 SPECIFICATIONS Back Cover ILLUSTRATIONS Page Figure 1 FRONT PANEL Figure 2 BACK PANEL Figure 3 REMOTE CONTROL 8 11 16 P N 1960101900389 CE Marking This product complies with the EMC direc tive 89 336 EEC and the low voltage direc tive 73 23 EEC Introduction Thank you for your purchase of the Krell Audio Video Standard To obtain the best performance from your Audio Video Standard surround preamp processor pay careful attention to its placement installa tion and operation A thorough understand ing of these det2. 14 Music engages Krell Music Surround circuitry for use with stereo recordings 15 Mono is for use with monophonic recordings This Provides monaural out put from the j nter speaker and sub woofer s only If the system does not include a center speaker the monaural signal is split between the left and right speakers 16 Preamp disengages all surround processing circuitry for use with stereo recordings When fed an analog source the Audio Video Standard functions as a pure Class A high resolution analog preamplifier For digital sources the Audio Video Standard employs 24 bit custom Krell written digital to analog conversion software before being sent to the analog preamplifier stage 17 Recall Button This button saves and recalls system config uration settings 18 Infrared Sensor he infrared sensor receives commands from the Audio Video Standard remote control For proper remote control operation make sure the infrared sensor is clear of any obstructions 19 21 Volume Control Buttons The following six buttons select one of the Audio Video Standard s volume channels 19 Master Volume Button When the LED above this button is illu minated the volume control knob 7 affects the entire system equally The vol KRELL Audio Video Standard ume adjustment is indicated in the main display and also on screen 20 Individual Channel Volume Trim When the LED above any of these
3. Auto Noise Sequence Set the SPL meter to C weighting and slow response After initializing the LEFT channel dB setting will be blinking and banded white noise will be heard through the left speaker This noise will continue for two seconds and then move clockwise to the next speaker in the system Using the up or down scroll but tons adjust each speaker s setting until the SPL meter reads 75dB This adjustment must be made while the individual channel is blinking Repeat for all remaining speakers When all the speakers are set press Previous twice to return to the main menu Manual Noise Sequence Set the SPL meter to C weighting and slow response After initializing the LEFT channel dB setting will be highlighted Press Enter and white noise will be heard from the left speaker as the 0 starts blinking Using the up or down scroll buttons adjust the setting until the SPL meter reads 75dB Press Enter and use the right scroll button to highlight the CENTER channel dB setting Using the same procedure as before set the CENTER channel volume to 75 dB Repeat for all remaining speakers When all the speakers are set press Previous twice to return to the main menu Notes When using an external noise generator for volume configuration sound will output simul taneously from all speakers in the system Adjustments can be made to any speaker in the system with the results immediately apparent to the balance of the whole sys
4. identifies the correct processing mode This occurs while changing laser DVD or com pact discs and BENOD tracks on a cd Mute protects your system by preventing the Audio Video Standard from playing back digital data in an incorrect format If the Audio Video Standard is going to be used as a digital to analog converter for music play back this muting may seem awkward because the beginning of each track may be affected You can change the format auto sensing to eliminate this muting if you wish To do so switch the unit into standby Press the DTS button 13 on the front panel and switch the Audio Video Standard out of standby to power on operate This will dis able the automatic muting feature of the Audio Video Standard and will alter the way in which the automatic format sensing oper ates For best results select DTS prior to lis tening to any DTS encoded material and be careful to select the proper format for each piece of software played through the digital BERG To re engage the automatic muting feature switch the Audio Video Standard into stand by and toggle the main power switch 38 on the rear panel to the off position When you restart your Audio Video Standard the Page 6 of 32 English automatic muting feature will be active Be sure to turn all amplifiers off when switching the main power switch on and off 10 Dolby Digital engages Dolby Digital AC 3 processin
5. REAR FULL RANGE X SUBS DUAL MONO OK The FRNT front CNTR center SIDE REAR and suBS subwoofers indicate possible speaker locations The x indicates speak ers that are currently present in the system the front speakers cannot be defeated hence the absence of parentheses For the FRNT CNTR SIDE and REAR selections the on screen menu offers the options of full range or bass limited The proper choice depends upon the low frequency capabilities of each speaker For the sugs selection the on screen menu offers the options of mono dual mono stereo or front and rear The default settings are displayed for each speaker If your system corresponds to the default settings highlight ox and press Enter You will be returned to the main menu and you may proceed to Step 2 listening room setup If you need to modify the speaker set tir gs proceed as follows KRELL Audio Video Standard Modifying speaker settings To disable a speaker highlight the appropri ate x and press Enter To enable a speaker highlight the appropri ate and press Enter To change the settings for the FRNT CNTR SIDE Or REAR highlight the appropriate phrase and press Enter The speaker setup menu will appear KRELL A V STANDARD SPEAKER SETUP IF THESE SPEAKERS ARE NOT DESIGNED TO REPRODUCE DEEP BASS CHECK THE BOX BELOW BASS LIMITED SPKR OK If the selected speaker does not have the c
6. the back of the Audio Video Standard Plug the remaining end into the AC wall receptacle Toggle the main power switch 38 to the up position The red power LED 9 will illuminate and the main display 4 will show Ac 3 for three seconds The Audio Video Standard is now ready for operation 6 Press either the front panel power button 8 or the remote control power button see Figure 3 44 on page 15 The word WAIT will appear in the main display and the initializing message will appear on screen To configure the Audio Video Standard for operation see System Configuration on page 18 KRELL Audio Video Standard Remote Control Description See Figure 3 on page 16 40 Analog Audio Input Buttons These buttons select the analog audio source B1 is a balanced input via XLR con nectors while S1 S5 are single ended inputs via RCA connectors The tape button allows access to an analog tape recorder 41 Digital Audio Input Buttons These buttons select the digital audio source C1 and C2 are coaxial inputs via RCA connectors T1 and T2 are TosLink inputs XLR is an AES EBU connection and HF is available via RCA or BNC connectors 42 Processing Mode Buttons The following six buttons select one of the Audio Video Standard s processing modes FCN the function button is reserved for future use The Audio Video Standard automatically selects which digital decoding format to use based on the input sig
7. Dolby Digital AC 3 Audio Mode LED 12 Dolby Pro Logic Audio Mode LED 13 DTS Audio Mode Button 14 Music Audio Mode Button 15 Mono Audio Mode Button 16 Preamp Audio Mode Button 17 Recall Button 18 Infrared Sensor 19 Master Volume Button 20 Individual Channel Volume Buttons 21 Balance Button Back Panel Description See Figure 2 on page 11 22 Balanced Channel Outputs The Audio Video Standard is equipped with nine channel utputs All nine channels are equipped with balanced outputs via XLR connectors as well as single ended connec tors 30 The nine channel outputs are for the center left right left and right side left and right rear and two subwoofer outputs labeled Sub1 Sub2 The XLR pin configurations are as follows Pin 1 Shield ground Pin 2 Non inverting 07 Pin 3 Inverting 180 23 Analog Tape Input The Audio Video Standard is equipped with one single ended tape input 24 Balanced Analog Inputs The Audio Video Standard is equipped with one balanced input labeled B1 via XLR connectors The XLR pin configurations are as follows Pin 1 Shield ground Pin 2 Non inverting 0 Pin 3 Inverting 180 25 Single Ended Analog Inputs The Audio Video Standard is equipped with five single ended inputs labeled S1 S5 via RCA connectors 26 RF Inputs The Audio Video Standard is equipped with an RF input for use with the Dolby Digital AC 3 RF out
8. but tons is illuminated the volume control knob 7 changes the level of the select ed channel These new changes will clear when a new input mode is selected The volume control knob reverts back to controlling the default level Master after four seconds of inactivity 21 Balance Button Preamp mode only When the LED above this button is illu minated the volume control knob 7 affects the left to right balance of the sys tem The center position is indicated by CNTR in the main display Balance may be adjusted in 1 dB increments up to 9 dB The next adjustment mutes either chan nel indicated by Rorr or Lorr for the right channel and left channel respectively The on screen representation for bal ance is graphical The center position is indicated by two vertical dots Each dB of adjustment is represented by one individual dot Moving the cursor so that it covers the L indicates a completely muted right chan nel Conversely positioning the cursor so that it covers the R indicates a complete ly muted left channel The volume control knob 7 reverts back to controlling the default level Master after four seconds of inactivity A English Page 7 of 32 n FIGURE 1 AUDIO VIDEO STANDARD FRONT PANEL 1 Tape 2 Analog 3 Digital In 4 Main Display 5 Composite 6 S Video 7 Volume Control Knob 8 Power Button 9 Power LED _ 10 Dolby Audio Mode Button 11
9. con vert video signal formats i e an S video input signal is output as an S video signal The same condition holds true for a com posite video signal The Audio Video Standard is equipped with three S video outputs and three com posite video outputs The main S video out put 28 and composite video output 35 include on screen graphics The composite video 1 output also has a parallel BNC con nector For dubbing purposes the second and third video outputs do not include on screen graphics These outputs may be con nected to the video inputs of your video recorders or to additional video monitors 4 Connect the outputs of the Audio Video Standard to the input s of your power amplifier s KRELL Audio Video Standard 4 Connect the outputs of the Audio Video Standard to the input s of your power amplifier s The Audio Video Standard has balanced outputs via XLR connectors and single ended outputs vja RCA connectors Both outputs are actiWe at all times allowing simultaneous connection to Separate ampli fiers Only one of these output formats should be connected to a single amplifier Note When connecting inputs or outputs to the Audio Video Standard remember that the balanced connections will have 6 dB more gain than the single ended connections If level matching becomes difficult in your installation keep this specification in mind 5 Plug the AC cord into the receptacle on
10. the original source while making a recording After selecting a source for recording B1 S1 S5 press the tape button to toggle between the tape recorder output LED illu minated and the input source LED not illu minated 2 Analog In The Analog In button activates the analog Input and cycles through the six analog audio inputs B1 is a balanced input via XLR connectors S1 S5 are single ended inputs via RCA connectors 3 Digital In The Digital In button activates the digital input and cycles through the six digital audio inputs C1 C2 T1 T2 XLR and RF The main display will show RF IN when the RF input for Dolby Digital AC 3 is selected C1 and C2 are coaxial inputs via RCA connectors T1 and T2 are TosLink inputs XLR is an AES EBU connection RF is available via RCA or BNC connec tors There is no front panel LED for this digital input B 4 Main Display The main display provides status messages for a variety of Audio Video Standard oper ations KRELL Audio Video Standard 5 Composite The composite video input button cycles through the four composite video inputs 6 S Video The S video input button cycles through the four S video inputs 7 Volume Control Knob The volume control knob adjusts the output level for the entire system as well as individ ual levels for the center speaker side speak ers rear speakers and subwoofers The vol ume control knob normally adjusts th
11. top of or beneath the Audio Video Standard For installations inside cabinetry make sure the Audio Video Standard has adequate air circulation Contact your dealer distributor or KrelP for furfher information Before you install the Audio Video Standard into your system review the following guidelines to choose the opti mum location for placement This will help ensure a clean trouble free installa tion For the dimensions of the Audio Video Standard see Specifications on back cover Page 4 of 32 English Place the Audio Video Standard surround preamp processor on a firm level surface away from dirt or moisture A minimum spac ing of three inches must exist between the Audio Video Standard and surrounding components to ensure proper ventilation AC POWER GUIDELINES WARNING Do not remove or bypass the ground pin on the end of the AC cord This may cause RFI radio frequency interference to be induced into your playback system The Audio Video Standard has superb reg ulation and does not require a dedicated AC circuit Avoid connections through extension cords or multiple AC adapters High quality 15 ampere grounded AC strips are accept able High quality AC line conditioners or fil ters may be used if they are grounded KRELL Audio Video Standard Front Panel Description See Figure 1 on page 8 1 Tape A tape monitor allows you to compare the output from your afialog tape recorder to
12. when the Audio Video Standard is powered on KRELL Audio Video Standard i a LLJ X O T a cC T e an o LLI E gt o o lt CN LLI om o LL 39 29 28 36 27 24 25 26 23 30 22 8 co 3f ideo Inputs ite V 9 34 33 uts Ou O e i 1 3 28 S 32 Outputs 2 j anne 3 34 Compos 22 Balanced Ch 29 Infrared Remote Sensors 30 Single Ended Channel Outputs 31 Digital Audio Outputs 32 Tape Outputs 23 Analog Tape Input 35 Composite Video Outputs 36 Composite Video BNC Input Output 37 IEC Power Connector 38 Main Power Switch 39 12 VDC Output 24 Balanced Analog Inputs 25 Single Ended Analog Inputs 26 Dolby Digital Inputs 27 S Video Inputs 33 Digital Audio Inputs Di Connecting the Audio Video Standard to Your System WARNING When making conne tions to this compo nent or any other make sure the power amplifier is off and the preamplifier is in the mute or stand by mode Make sure all cable terminations are of the highest gual ity free from frayed ends shorts or cold solder joints 1 For analog audio sources connect the left and right outputs of your source com ponents to the inputs on the Audio Video Standard The Audio Video Standard is equipped with six single ended analog audio inputs S1 S5 and tape via RCA conn
13. ACKGROUND COLOR Highlight BACKGROUND COLOR and press Enter The background color menu will appear KRELL A V STANDARD BACKGROUND COLOR MENU BACKGROUND COLOR X BLACK BLUE GREEN RED OK The default background color is black If blue green or red is preferred highlight the appropriate and press Enter The back ground color will immediately change to the new setting When you are finished highlight OK and press Enter to return to the operation menu Page 26 of 32 English VOLUME The default on screen volume display is numerical The Audio Video Standard s vol ume control ranges from O to 152 with 89 representing the Dolby reference level To change the main volume to a bar graph dis play highlight MAIN VOLUME DISPLAY and press Enter The main volume display menu will appear KRELL A V STANDARD MAIN VOLUME DISPLAY HOW WOULD YOU LIKE THE MAIN VOLUME DISPLAYED X BARGRAPH DISPLAY NUMERIC DISPLAY OK Highlight the beside BARGRAPH DISPLAY and press Enter The on screen display will now show the current volume setting relative to maximum volume Total volume is repre sented by sixteen dots As volume increas es squares replace the dots At Dolby refer ence level 89 the volume control pauses and displays REF on screen When finished highlight ox and press Enter to return to the operation menu ON SCREEN DELAY TIME On screen information remains visi
14. EO INPUTS 4 S Video 4 Composite 1 BNC ANALOG CHANNEL OUTPUT Left center right side surrounds rear sur JJ rounds 2 subwoofers Balanced via XLR or engi ance via RCA ANALOG TAPE OUTPUTS 1 audio via RCA 2 video via RCA Audio Video Standard Surround Preamp Processor DIGITAL OUTPUTS 1 coaxial 1 TosLink VIDEO OUTPUTS 3 S Video 1 with on screen graphics 3 Composite 1 with on screen graphics 1 BNC with on screen graphics LISTENING MODES Dolby Digital AC 3 DTS Dolby Pro Logic Music Mono Preamp DIMENSIONS 19w x 6 75h x 17d in 48 3w x 17 2h x 43 2d cm WEIGHT Shipped 42 ibs 19 1 kg Unit only 24 ibs 10 9 kg All operational features functions specifications and policies are subject to change without notification
15. SET S VIDEO INPUTS SV1 SV2 SV3 SV4 COMPOSITE VIDEO INPUTS CV1 CV2 CV3 CV4 Highlight any of the S video or composite video inputs and press Enter A secondary screen will appear KRELL Audio Video Standard KRELL A V STANDARD LINK INPUT WHICH INPUT LINK DO YOU WANT TO CHANGE ANALOG Highlight the audio input style either ANALOG or DIGITAL and press Enter If ANALOG is selected an additional screen appears KRELL A V STANDARD LINK INPUT SELECT AN ANALOG INPUT TO LINK TO SV1 8 si s2 s3 s4 ss OK Highlight the appropriate analog input and press Enter When completed highlight ox and press Enter to return to the link input menu At this point you may choose a digital input or operating mode to link with the selected video input To select a linked digital input highlight DIGITAL 5 and press Enter The digital link input screen will appear KRELL A V STANDARD 7 LINK INPUT SELECT A DIGITAL INPUT TO LINK TO SV1 COAX 1 oPrc1 coax2 oPrc2 AES EBU RF OK KRELL Audio Video Standard Note If a video input is linked to both a digital and an analog input the Audio Video Standard will select the digital input as the main audio source whenever the video input is selected When completed highlight ok and press Enter to return to the link input menu At this point you may choose to change the linked operating mode To change a linked oper
16. System Configuration The remote control is the main input device for the Audio Video Standard All initial setup and subsequent system configuration adjustments must be made via the remote control The remote control also includes functions for Krell power amplifiers For maximum performance the Audio Video Standard needs to be configured for system elements their capabilities and positions within the listening room This infor mation is entered into the Audio Video Standard via on screen menus These menus are structured to guide you through the setup Mera ACCESSING THE MAIN MENU To begin the system configuration proce dure connect the on screen video output of the Audio Video Standard 28 or 35 to your video monitor Set the video monitor to this input Press the remote control menu button 51 and the main menu screen will appear KRELL A V STANDARD MAIN MENU CONFIGURE SPEAKEHS LISTENING ROOM SETUP CALIBRATE VOLUME CONFIGURE INPUTS CONFIGURE MUSIC MODE OPERATION The Audio Video Standard is now ready for configuration Page 180f32 English STEP 1 CONFIGURE SPEAKERS To configure the Audio Video Standard for the specific types of speakers used in the system highlight CONFIGURE SPEAKERS and press the enter button 49 The speaker Sye tem setup menu will appear KRELL A V STANDARD SPEAKER SYSTEM SETUP PRSNT TYPE FRNT FULL RANGE x CNTR FULL RANGE X SIDE FULL RANGE x
17. TO MOVE CURSOR T amp TO CHANGE TEXT PRESS ENTER WHEN DONE The first letter of the input name will blink and can be changed using the up or down scroll buttons Move the blinking cursor to the letter you want to change and adjust to the letter of your choice The name field is limited to a maximum of 12 characters Available char acters are A Z 1 9 lt gt and a blank space When completed press Enter to finish the editing and return to the input name menu Choose another input to adjust or press Previous to return to the input name menu Choose another input name to modify or press Previous to return to the configure inputs menu English Page 21 of 32 Special Analog Sources The analog input sensitivity of the Audio Video Standard is set for the standard 2 Volts that Dolby Laboratories mandates for proper Dolby Pro Logic processing For analog sources components connected to 1 S5 and tape that do ng correspond to a stan dard 2 Volt output Specification it may be necessary to adjust individual input levels on the Audio Video Standard Press Menu to exit the menu system select the desired analog input and return to the configure inputs menu Highlight SET ANALOG INPUT LEVEL and press Enter The set input levels menu will appear KRELL A V STANDARD SET INPUT LEVELS INPUT B1 L R OVERLOAD LEVEL O DB OK o Begin playback of the selected source using program material with loud pas
18. a pure Class A high resolution analog preamplifier For digital sources the Audio Video Standard employs 24 bit custom Krell written digital to analog conversion software before being sent to the analog preamplifier stage 43 Levels Buttons These buttons select one of the Audio Video Standard s volume channels Master selects all channels for system Wide volume control Balance Preamp Mode Only adjusts the left to right balance of the system Mute interrupts any audio signal to source eguipment 44 Power Button The power button toggles the Audio Video Standard from standby to operate 45 Vol Down Vol Up Buttons The vol down and vol up buttons control the volume for either the entire system or for an KRELL Audio Video Standard individual channel as a de the levels buttons 43 46 Amplifier Buttons The power and meter buttons operate Krell amplifiers 47 System Button These buttons select a preassigned video _ input Once a video input is assigned it may then be linked to a specific audio input and surround mode For details on this assigning and linking procedure see Direct Access Remote Control System Programming on page 24 48 Video Buttons o These buttons select the video source CV1 CV4 are composite video inputs and SV1 SV4 are S video inputs KRELL Audio Video Standard 49 Enter Button This button inputs on screen menu selec tions functions only
19. ails will help insure satisfac tory operation and long life for the Audio Video Standard and related system compo nents 39 THERE ARE NO USER SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT Please contact your authorized dealer distributor or Krell if you have any ques tions not addressed in this reference manual KRELL Audio Video Standard Unpacking 1 Open the box and remove the top layer of foam You will see these items Audio Video Standard AC power cord Audio Video remote control AAA batteries T 10 Torx wrench packet containing an introductory letter from Dan D Agostino C E O the Owners Reference and the Warranty Registration Card wah sch JS sch sch sch Note If any of these items are not included please contact your authorized Krell dealer or dis tributor immediately for assistance 2 Carefully remove the unit and acces sories from the box Remove the protec tive plastic wrap from the unit Note Save all packing materials If you must ship your Audio Video Standard in the future repack the unit in its original packaging to prevent transit damage English Page 3 of 32 Placement WARNING The surround preamp processor must not be located where it could be exposed to drip IMPORTANT The ventilation grids and cooling fan on the top of the Audio Video Siandard need to be unobstructed at all times during opera tion Do not place flammable material on
20. apability to reproduce low frequencies high light the press Enter highlight ok and press Enter again You will be returned to the speaker system setup menu The on screen phrase for the selected speaker will now read BASS LIMITED To change the settings for the subwoofers highlight suBs and press Enter The configure subwoofers menu will appear KRELL A V STANDARD CONFIGURE SUBWOOFERS SELECT A CONFIGURATION SINGLE MONO SUB X DUAL MONO SUBS STEREO SUBS FRONT amp REAR SUBS OR KRELL Audio Video Standard Highlight the appropriate that represents the subwoofer configuration in your system and press Enter The x will now appear next to the new subwoofer setting Highlight OK and press Enter You will be returned to the speaker system setup menu Highlight OK and press Enter again to return to the main menu STEP 2 LISTENING ROOM SETUP To tell the Audio Video Standard where each speaker is located within the listening room highlight LISTENING ROOM SETUP and press Enter The listening room setup menu will appear KRELL A V STANDARD LISTENING ROOM SETUP LEFT CENTER RIGHT O FT 0 FT 0 FT L SIDE SUB 1 R SIDE OFT OFT 0 FT L REAR SUB 2 R REAR O FT OFT OFT The o FT under LEFT will be highlighted Press Enter and the 0 will start blinking Use the up scroll button 50 to increase the number to the correct distance in feet from the main lis tening positio
21. ase as noted on the retail sales slip provided by an authorized Krell dealer or distributor or on the warranty registration card sent to Krell In the event that an ade quate proof of purchase date is unavailable the warranty period will begin on the date the product was originally shipped from the fac tory The warranty described in this para graph shall be in lieu of any other warranty express or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose There are no warranties which exceed beyond those described in this document If this product does not perform as warranted herein the owners sole remedy shall be repair In no event will Krell be liable for incidental or con Page 30 of 32 English sequential damages arising from purchase use or inability to use this product even if Krell has been advised of the possibility of such damages The warranty for this Krell product is valid only in the country to which the product was originally shipped through the authorized Krell distributor for that country and at the factory There may be restrictions on or changes to Krell s warranty because of reg ulations within a specific country Please check with your distributor for a complete understanding of the warranty in your coun try Freight to the factory is your responsibility Return freight within the United States U S A is includ
22. at ing mode highlight mope and press Enter The operating mode link input screen will appear KRELL A V STANDARD LINK INPUT SELECT A MODE TO LINK TO SV1 x MOVIE MUSIC PREAMP OK Notes If a video input is linked to a digital input and MOVIE is in the linked mode the Audio Video Standard will select the appropriate digital surround processing mode either Dolby Pro Logic Dolby Digital or DTS depending upon which signal is present If a video input is linked to an analog input and MOVIE is the linked mode the Audio Video Standard will select Dolby Pro Logic as the surround processing mode If a video input is linked to any analog or digi tal input and MUSIC or PREAMP is the linked mode the Audio Video Standard will process the linked audio signal in the select ed mode unless the input is a digital signal containing either Dolby Digital or DTS data In English Page 23 of 32 this case the appropriate processing mode will be selected Highlight the desired mode and press Enter When completed highlight ok and press Enter to return to the link input menu Select another video input to link or press Previous to return to the configur inputs menu Direct Access Remote Control System Programming System programming functions allow you to simplify the use of your Audio Video Standard by naming three sets of linked inputs System 1 2 and 3 47 Other links may be created in
23. ble for three seconds The on screen delay time has a range from one to five seconds To adjust highlight ON SCREEN DELAY TIME and press Enter The on screen delay time menu will appear KRELL Audio Video Standard KRELL A V STANDARD ON SCREEN DELAY HOW LONG WOULD YOU LIKE THE TEXT TO REMAIN ON THE SCREEN AFTER VOLUME ADJUSTMENT OR CHANGING INPUT AND MODES 3 SECONDS Press Enter and the 3 will begin blinking Use the up or down scroll buttons to increase or decrease the on screen time setting and then press Enter to lock in the new setting When finished press EES to return to the operation menu INPUT LINK PROPERTIES The input linking feature activates as soon as the inputs are joined in the configure inputs menu These links are not shown on screen unless instructed To change either of these settings highlight INPUT LINK PROPER TIES and press Enter The input link proper ties menu will appear KRELL A V STANDARD INPUT LINK PROPERTIES X ENABLE INPUT LINKS SHOW LINKS WHILE CHANGING INPUTS OK To disable the input links highlight the x next to ENABLE INPUT LINKS and press Enter The video audio and mode settings now operate independently To display the input links highlight the next to SHOW LINKS WHILE CHANGING INPUTS and press Enter The video audio and mode settings of the active link plus the current volume setting will be KRELL Audio Video Standard displa
24. cept all liability for loss or damage to the product during shipment to the Krell factory and prepay all ship ping charges The product may also be hand delivered if arrangements with the Service Department have been made in advance Proof of purchase may be required for warranty validation at the time of hand delivery 3 Use the original packaging to insure the safe transit of the product to the factory dealer or distributor The use of any packaging material other than the origi nal packaging materials is not recom mended Krell may at its discretion return a product in new packaging and bill the owner for such packaging if the product received by Krell was boxed in non standard packaging or if the original packaging was so damaged that it was unusable If Krell determines that new packaging is required the owner will be notified before the product is returned To purchase additional packaging please KRELL Audio Video Standard PRODUCT contact your authorized Krell dealer dis tributor or the Krell Service Department for assistance Krell is not responsible for any damage incurred in transit Krell will file claims for damages as necessary for products dam aged in transit to the factory The owner is responsible for filing claims for shipping damages that occur EENS the return ship ment Replacement parts and or products will be furnished on an exchange basis only any parts and or produ
25. cts returned to Krell for exchange become the property of Krell No expressed or implied warranty is made for any Krell product damaged by accident abuse misuse natural or personal disaster or unauthorized modification In the event Krell receives a product for war ranty service which has been modified in any way without Krell authorization all war ranties on that product will be void The prod uct will be returned to original factory layout specifications at the owner s expense before it is repaired All repairs required after the product has been returned to original factory specification will be charged to the customer at current parts and labor rates To contact the Krell Service Department TEL 203 799 9954 Monday Friday 9 00 AM to 5 00 PM EST FAX 203 799 9796 E MAIL krell 9 krellonline com Audio A Video Standard SERIAL NUMBER To register your product for warranty benefits complete and return the Warranty Registration Card enclosed in the shipping box within 15 days of purchase English Page 31 of 32 Krell Industries Inc 45 Connair Road Orange CT 06477 3650 USA TEL 203 799 9954 FAX 203 799 9796 E MAIL krell krellonling com WEB SITE www ei line com Specifications ANALOG AUDIO INPUTS 5 single ended via RCA 1 balanced via XLR 1 single ended tape input DIGITAL AUDIO INPUTS 2 coaxial 2 TosLink 1 AES EBU 1 RF input for Dolby Digital AC 3 VID
26. dio Inputs The Audio Video Standard is equipped with five digital audio inputs in the following formats Two coaxial via RCA connectors Two TosLink One AES EBU vid an XLR connector 34 Composite Video Inputs The Audio 4 Video Standard is equipped with four RCA composite video inputs labeled 1 4 35 Composite Video Outputs The Audio 4 Video Standard is equipped with three RCA composite video outputs The main composite video output labeled on screen includes on screen graphics For dubbing purposes the second and third composite video outputs do not include on screen graphics 36 Composite Video BNC Input Output The Audio Video Standard includes one composite video input and one composite video output via BNC connectors These Page 10 of 32 English ports are electrically identical to the RCA composite video inputs 34 and outputs 85 Note You may simultaneously use both RCA and BNC outputs but only one of the inputs 37 IEC Power Connector The Audio Video Standard is equipped with a standard female IEC power connec tor 38 Main Power Switch Toggles the Audio Video Standard between off and standby 39 12 VDC Output Activated by the front panel power button 8 the 12 VDC output sends a 12 volt power on off signal to other Krell components as well as to other devices that incorporate a 12 volt power on off trigger input This allows for remote turning on off of other compo nents
27. e mas ter volume as indicated by the LED illuminat ed above the master button 19 The change in volume is indicated in the main display and also on screen Adjustments to the center speaker side speakers rear speakers and subwoofers are made by pressing the corresponding individual chan nel volume buttons 20 and rotating the vol ume control knob to the desired setting The master volume control has a numerical range from 0 to 152 with 89 being the Dolby reference The center speaker side speak ers rear speakers and subwoofer volume trim have a range of 12 dB 8 Power Button The power button toggles the Audio Video Standard from standby to operate and also switches the 12 VDC output between on and off 9 Power LED The power LED illuminates when the rear panel main power switch see Figure 2 38 on page 11 is placed in the on position During remote control operation the power LED will flash indicating the Audio Video Standard is EE remote control com mands English Page 5 of 32 10 16 Audio Mode Buttons The five buttons 10 13 14 15 and 16 select one of the Audio Video Standard s audio modes The Audio Video Standard automatically selects which digit al decoding format to use based on the input signal it receives When a silent digital signal is present the Audio Video Standard will automatically mute its output until program material resumes and the Audio Video Standard
28. ectors and one bal anced analog audio input B1 via an XLR connector 2 For digital audio sources connect the digital audio output of your source com ponents to the digital inputs on the Audio Video Standard The Audio Video Standard is equipped with five digital inputs two coaxial inputs via RCA con nectors two TosLink optical connec tions and one AES EBU via an XLR connector For Dolby Digital AC 3 sur round processing connect the RF output of a laser disc player to one of the RF inputs Note For source units that are equipped with both digital and analog audio outputs higher per formance will generally result when connect ing source units to the Audio Video EES l using a digital audio output Page 12 of 32 English 3 Connect the video outputs of your video sources to the video inputs on the Audio Video Standard The Audio Video Standard is equipped with four S video inputs and four composite video inputs S video cables transmit the color and luminance components of the video signal separately This separation is performed by the comb filter within the source unit If the source unit s comb filter is superior to the one within the video monitor S video connections should be used Otherwise a composite video connection should be used Notes S video cables should not be used for lengths greater than 20 feet for optimum performance The Audio Video Standard does not
29. ed in the warranty If you have purchased your Krell product outside the U S A and wish to have it serviced at the factory all freight and associated charges to the factory are your responsibility Krell will pay return freight to the U S A based freight forwarder of your choice Freight and other charges to ship the product from the freight forwarder to you are also your responsibility The operating voltage of this product is determined at the factory and can only be changed by an authorized Krell distributor or at the factory The voltage for this product in the U S A cannot be changed for six months from the original purchase date Any unauthorized voltage conversion disassembly component replacement perforation of chassis updates or modifications performed to the product will void the warranty KRELL Audio Video Standard Return Authorization Procedure IMPORTANT If you believe there is a problem with your component please contact your dealer dis tributor or the KfelP factory to discuss the problem before you return the component for repair To expedite service you may wish to complete and e mail the Service Request Form on our website at www krellonline com To return a product to Krell please fol low this procedure so that we may serve you better 1 Obtain a Return Authorization Number R A number and shipping address from the Krell Service Department 2 Insure and ac
30. feature will be active Be sure to turn all amplifiers off when switching the main power switch on and off Dolby Digital engages Dolby Digital AC 3 processing for use with Dolby Digital AC 3 encoded source material The Audio Video Standard automati cally switches to Dolby Digital AC 3 pro cessing upon receiving a Dolby Digital AC 3 encoded signal No user interven tion is required after the appropriate digi tal input is selected and connected Dolby Pro Logic engages Dolby Pro Logic circuitry for use with all Dolby sur round processing encoded material This includes laser discs videotapes televi sion broadcasts and compact discs DTS engages DTS digital surround pro cessing for use with DTS encoded source material The Audio Video Standard automatically switches to DTS processing upon receiving a DTS signal No user intervention is required after the Page 14 of 32 English appropriate digital input is selected and connected Music engages Krell Music Surround circuitry for use with stereo recordings Mono is for use with monophonic recordings This provides monaural out put from the center speaker and sub woofer s only If the system does not include a center speaker the monaural signal is split between the left and right speakers Preamp disengages all surround pro cessing circuitry for use with stereo recordings When fed an analog source the Audio Video Standard functions as
31. g for use with Dolby Digital AC 3 encoded source material The Audio Video Standard automati cally switches to Dolby Digital AC 3 pro cessing upon receiving a Dolby Digital AC 3 encoded signal No user interven tion is required after the appropriate digi tal input is selected and connected Dolby Pro Logic engages Dolby Pro Logic circuitry for use with all Dolby sur round processing encoded material This includes laser discs videotapes televi sion broadcasts and compact discs 11 The Dolby Digital LED is lit and the Dolby Pro Logic LED 12 is not lit when the Audio Video Standard is in the Dolby Digital AC 3 decoding mode When both the Dolby Digital LED and the Dolby Pro Logic LED are lit the Audio Video Standard is decoding a Dolby Digital AC 3 encoded Dolby Pro Logic signal 12 The Dolby Pro Logic LED is lit and the Dolby Digital LED 11 is not lit when the Audio Video Standard is in the Dolby Pro Logic decoding mode When both the Dolby Digital LED and the Dolby Pro Logic LED are lit the Audio Video Standard is decoding a Dolby Digital AC 3 encoded Dolby Pro Logic signal 13 DTS engages DTS digital surround processing for use with DTS encoded source material The Audio Video Standard automatically switches to DTS processing upon receiving a DTS signal No user intervention is required after the KRELL Audio Video Standard appropriate digital input i is selected and connected
32. ght CONFIGURE SPEAKERS and press Enter A second screen will appear KRELL A V STANDARD CONFIGURE MUSIC MODE SELECT THE SPEAKERS TO BE ACTIVE IN MUSIC MODE SIDE SPEAKERS REAR SPEAKERS OK Highlight the speakers to be active in the music mode and press Enter When com pleted highlight ok and press Enter to return to the main configure music mode menu Before proceeding highlight ADJUST OUTPUT LEVELS and press Enter The configure music mode menu will appear KRELL A V STANDARD CALIBRATE MUSIC MODE LEFT RIGHT 0 DB 0 DB L SIDE SUB 1 H SIDE O DB 0 DB 0 DB L REAR SUB 2 R REAR O DB 0 DB 0 DB The displayed speaker array will duplicate the system profile input into the speaker sys tem setup menu The center speaker is not displayed because it is not active in the music mode The Audio Video Standard is now calibrated and setup for all movie modes and music mode Select the appro priate audio and video input and simply turn up the volume KRELL Audio Video Standard English Page 25 of 32 Operation The operation menu offers options for a vari ety of Audio Video Standard user opera tions and features From the main menu high light OPERATION and press Enter This opera tion menu will appea KRELL A V STANDARD OPERATION BACKGROUND COLOR MAIN VOLUME DISPLAY ON SCREEN DELAY TIME INPUT LINK PROPERTIES REMOTE CONTROL SENSOR FULL SURROUND SETUP ANTI CLIP CONTROL B
33. ies that use both the NTSC and PAL broadcasting sys tems the SV 3 SV 4 CV 3 and CV 4 are factory set to the PAL operating system To adjust the broadcast operating settings for any of the video inputs enter the PAL video setup menu located within the configure inputs menu KRELL A V STANDARD PAL VIDEO SETUP SELECT THE INPUTS THAT HAVE PAL VIDEO SOURCES sv1 ov1 sv2 ov2 sv 3 cv a svc4 cv 4 OK Highlight the inputs that have PAL video sources attached to them and press Enter so that an x appears next to the desired input To defeat a PAL video source press Enter so the x disappears When completed highlight ox and press Enter to return to the KRELL Audio Video Standard a DT Ste a s te EE E an pnt Er AE EZE veer f jd i x S configure inputs menu Press Previous to return to the main menu STEP 5 CONFIGURE THE MUSIC MODE It is often desiragle to have the settings for music listening different from movie listening Highlight CONFIGURE MUSIC MODE and press Enter The configure music mode screen will appear KRELL A V STANDARD CONFIGURE MUSIC MODE THE A V STANDARD WILL BE SET TO MUSIC MODE OK TO CONTINUE YES NO Highlight yes and press Enter The configure music mode screen will appear KRELL A V STANDARD CALIBRATE MUSIC MODE ADJUST OUTPUT LEVELS CONFIGURE SPEAKERS NOTE THESE ADJUSTMENTS ARE FOR MUSIC MODE ONLY Highli
34. in the menu mode 50 Scroll Buttons These four buttons scroll on screen menu options and also are used for volume con trol 51 Menu Button This button accesses the on screen menu functions 52 Previous Button This button escapes or ends certain on screen menu operations English Page 15 of 32 a o as ke lt Q o O Lu an Q LC lt m Gu o LL gt E Q m t Di Cc o LL UUR deo Buttons 48 V 44 Power Button Input Buttons i 40 Analog Aud 41 Digital Aud 49 Enter Button 45 Vol Down Vol Up Buttons Input Buttons IO 50 Scroll Buttons 51 Menu Button Buttons ler i 46 Ampl 42 Processing Mode Buttons 47 System Buttons 43 Levels Buttons 52 Previous Button deo Standard i io V KRELL Aud English Page 16 of 32 BATTERY INSTALLATION AND REMOVAL Note Batteries should be replaced when functions from the remote control become intermittent The Audio Video Standard remote uses four AAA size 1 5 olt batteries Dd 1 Remove the backplate to expose the bat teries i KRELL Audio Video Standard Remove the old batteries Install the new batteries following the battery position diagram on the plastic battery receptacle Re install the backplate Check to make sure the remote control is functioning properly English Page 17 of 32 b
35. l surround setup menu will appear KRELL A V STANDARD FULL SURROUND SETUP IF YOU WOULD LIKE BOTH THE SIDES AND REARS ACTIVE IN ALL THEATER MODES CHECK THE BOX BELOW FULL SURROUND MODE OK Highlight the next to FULL SURROUND MODE and press Enter When finished highlight ok and press Enter to return to the operation menu E ANTI CLIP CONTROL For proper Dolby Pro Logic surround pro cessing when using an analog source an anti clip circuit is used to prevent over driving the Dolby surround processing circuitry The Page 28 of 32 English Audio Video Standard presents a CD or DAT recordable signal to the digital outputs when an analog signal is inputted When recording an analog music source onto a digital medium the use of the anti clip con trol may limit dynamics and impart an unwanted compression to the music To disable the anti clip control highlight ANTI CLIP CONTROL on the operation menu and press Enter The anti clip control menu will appear KRELL A V STANDARD ANTI CLIP CONTROL X ENABLE DISABLE OK Highlight the next to DISABLE and press Enter When finished highlight ok and press Enter to return to the operation menu Note The anti clip control will be reactivated when an input is changed KRELLO Audio Video Standard Saving Recalling and Clearing EE Settings To save your configuration settings turn the Audio Video Standard off from
36. n to the left speaker Press Enter again and the number will stop blink ing Use the right scroll button to highlight the 0 FT under CENTER Press Enter and the 0 will start blinking Using the same procedure as before input the correct distance for the cen ter speaker Do the same for the remaining speakers in the system After all the dis tances are set press the Previous button 22 to return to the main menu English Page 19 of 32 Note WW Any speaker not configured in the speaker system setup menu will display N A not available for the distance specification STEP 3 CALIBRATE THE VOLUME Note P A sound pressure level SPL meter is nec essary for this procedure To adjust individual speaker outputs for prop er balance throughout the system highlight CALIBRATE VOLUME and press Enter The cali brate volume menu will appear KRELL AV STANDARD CALIBRATE VOLUME SELECT THE CHANNEL CALIBRATION METHOD AUTO NOISE SEQUENCE MANUAL NOISE SEQUENCE PROGRAM MATERIAL Highlight one of the choices and press Enter If you choose AUTO NOISE SEQUENCE Or MANUAL NOISE SEQUENCE the message INITIALIZING will blink while the Audio Video Standard loads its internal noise generator The follow ing screen will then appear KRELL A V STANDARD CALIBRATE VOLUME LEFT CENTER RIGHT 0 DB 0 DB 0 DB LSIDE SUB1 R SIDE 0 DB 0 DB ODB LREAR SUB2 RREAR 0 DB 0 DB 0 DB Page 20 of 32 English
37. nal it receives When a silent digital signal is present the Audio 4 Video Standard will automatically mute its output until program material resumes and the Audio 4 Video Standard identifies the correct processing mode This occurs while changing laser DVD or com pact discs and between tracks on a cd Mute protects your system by preventing the Audio Video Standard from playing back digital data in an incorrect format If the Audio Video Standard is going to be used as a digital to analog converter for music playback this muting may seem awkward because the beginning of each track may be affected You can change the format auto English Page 13 of 32 sensing to eliminate this muting if you wish To do so switch the unit into standby Press the DTS button 13 on the front panel and switch the Audio Video Standard out of standby to power on operate This will dis able the automatic muting feature of the Audio Video Stangard and will alter the way in which the autorflatic format sensing oper ates For best results select DTS prior to lis tening to any DTS encoded material and be careful to select the proper format for each piece of software played through the digital inputs To re engage the automatic muting feature switch the Audio Video Standard into stand by and toggle the main power switch 38 on the rear panel to the off position When you restart your Audio Vid o Standard the automatic muting
38. put of a laser disc player KRELL Audio Video Standard Connections are via RCA or BNC coaxial digital cable 27 S Video Inputs The Audio Video Standard is equipped with four S video inputs labeled 1 4 28 S Video Outputs The Audio Video Standard is equipped with three S video outputs The main S video output labeled on screen includes on screen graphics For dubbing purposes the second and third S video outputs do not include on screen graphics 29 Infrared Remote Sensors The Audio Video Standard is equipped with an additional infrared sensor and a male baseband RC 5 remote input for custom installations 30 Single Ended Channel Outputs The Audio Video Standard is equipped with nine channel outputs All nine channels are equipped with single ended outputs via RCA connectors as well as balanced con nectors 22 The nine channel outputs are for the center left right left and right side left and right rear and two subwoofer out puts labeled Sub1 Sub2 31 Digital Audio Outputs The Audio Video Standard is equipped with two digital audio outputs in the following formats One coaxial via RCA connector One TosLink 32 Tape Outputs The Audio Video Standard is equipped with three analog tape outputs Two are for use with video sources labeled VCR1 VCR2 and the third is for use with an audio tape deck labeled tape English Page 9 of 32 33 Digital Au
39. sages Press Enter The LEVEL dB specification will begin blinking If the source unit s output is greater than the standard 2 Volts ovERLOAD will blink indicat ing an input signal greater than standard Using the down scroll button lower the level db setting until OVERLOAD stops blinking Conversely if the source unit s output is less than the standard 2 Volts it will be necessary to raise the input level sensitivity for proper Dolby surround processing Using the up Page 22 of 32 English scroll button raise the level dB setting until OVERLOAD Starts blinking and then reduce the setting just below this threshold When the input level has been properly set highlight ok and press Enter to return to the configure inputs menu To adjust additional inputs exit the menu system by pressing Menu select the desired input return to the set input levels menu within the configure inputs menu and follow the same procedure as above Linking a Video Input to an Audio Input Each video input S video and composite video may be linked to a specific audio input and surround mode Therefore when a video input is configured and then selected its matching audio input and surround mode will also engage Highlight SET VIDEO INPUT LINKS within the configure inputs menu and press Enter The set video input links menu will appear KRELL A V STANDARD SET VIDEO INPUT LINKS WHICH VIDEO INPUT LINKS WOULD YOU LIKE TO
40. tem Any speaker not configured in the speaker system setup menu will display N A Not available for the dB specification KRELL Audio Video Standard The subwoofer designation will change depending on the configuration entered in the speaker system setup menu For a mono setup the subwoofers are designated SUB 1 and sub 2 For a left and right stereo setup the subwoofers are designated suB L and SUB R For a front and rear setup the sub woofers are designated SUB F and SUB R E uses STEP 4 CONFIGURE THE INPUT To configure inputs highlight CONFIGURE INPUTS and press Enter The configure inputs menu will appear KRELL A FV STANDARD CONFIGURE INPUTS EDIT INPUT NAMES SET ANALOG INPUT LEVEL SET VIDEO INPUT LINKS PAL VIDEO SETUP Highlight EDIT INPUT NAMES and press Enter The input name type menu will appear KRELL A FV STANDARD INPUT NAME WHAT TYPE OF INPUT NAME DO YOU WANT TO CHANGE VIDEO ANALOG DIGITAL Highlight VIDEO and press Enter The input name menu will appear KRELL Audio Video Standard KRELL A FV STANDARD INPUT NAME WHICH INPUT NAME DO YOU WANT TO CHANGE S VIDEO INPUTS SV1 SV2 SV3 SV4 COMPOSITE VIDEO INPUTS CV1 CV2 CV3 CV4 Highlight any of the S video or composite video inputs and press Enter A secondary screen will appear S video 1 is shown as an example KRELL A V STANDARD INPUT NAME INPUT S VIDEO 1 NAME S VIDEO 1 amp 2
41. the Audio Video Standard but primary links may be set up and remembered more easily with the System function For example System button 1 A laser disc con nected to the RF input and a video input set for MOVIE MODE System button 2 A DVD player con nected to the C1 input and a video input set for MOVIE MODE System button 3 A CD player con nected to an analog input and an unused video input set for preamp mode To use the system programming function the basic input links need to be created For details see Linking a Video Input to an Audio Input on page 22 To assign input links to System 1 2 or 3 follow the instructions below 1 Push and release one of the three Sys _tem buttons 2 Decide which video input you want to assign to the system button Push and Page 24 of 32 English hold the appropriate video button down for approximately five seconds Note that the red LED in the upper left corner of the remote control will blink When the blink ing stops and the light stays lit for one second the system is linked to the video input you selected 3 Link the video inputs to a specific audio input and surround mode Selecting the Broadcast Standard The Audio Video Standard will operate in both the NTSC and PAL broadcasting stan dards For countries that only use the NTSC broadcasting standard all S video and com posite video inputs are already set for prop er NTSC operation For countr
42. the front panel or the rem te control While pressing the recall button 17 press the power button 8 on the front panel The main display will read SAVE CNFG when the settings have been stored in the Audio Video Standard s non volatile memory KRELLO Audio Video Standard To recall your stored configuration settings press Recall until RSTR CNFG appears in the main display This will take thirteen seconds To clear all settings turn the Audio Video Standard off from the front panel or the remote control While pressing both master 19 and balance 21 buttons press the power button on the front panel The main display will read CLR When the settings have been erased from the Audio Video Standard s non volatile memory English Page 29 of 32 Warranty Krell warrants this product to be free from defects in material or workmanship for a period of five years for circuitry from the orig inal date of purchase Should this product fail to perform at any time during the warranty Krell will repair dt at no cost to the owner except as set forth in this warranty Transfer of warranty to a second owner occurs auto matically Please contact Krell to have the name on the warranty changed Transfer of warranty does not extend the duration of the original warranty period Note This warranty does not apply to damage caused by acts of God or nature The warranty period begins on the date of retail purch
43. yed on screen whenever a video input is changed REMOTE CONTROL SENSOR Tne Audio Video Standard receives infrared remote commands at the front panel infrared sensor 18 Additionally the Audio Video Standard features a duplicate remote sensor and a male baseband infrared connector 29 on the rear panel These rear panel infrared components may be used to facilitate a cus tom installation To activate these features highlight REMOTE CONTROL SENSOR and press Enter The remote control sensor menu will appear KRELL A V STANDARD REMOTE CONTROL SENSOR X USE FRONT SENSOR USE REAR SENSOR OK Highlight the next to USE REAR SENSOR and press Enter The rear infrared sensor will now be active and the front panel infrared sensor will be disabled When finished high light OK and press Enter to return to the oper ation menu Note To reactivate the front infrared sensor the Audio Video Standard must be in standby mode While holding the front panel S video button 6 and the composite video button 5 down simultaneously press the power but ton 8 FULL SURROUND SETUP For systems with both side and rear speak ers the Audio Video Standard offers the option of operating both pairs of surround English Page 27 of 32 1 speakers in all theater modes To activate both pairs of speakers in any theater mode highlight FULL SURROUND SETUP on the opera tion menu and press Enter The ful
Download Pdf Manuals
Related Search