Kenwood KDC-W534Y Car Stereo System User Manual
Contents
1. Source required Display Tuner TUNER CD CD Standby Illumination only mode STANDBY This unit automatically turns full power OFF after 20 minutes lapses in Standby mode in order to save the vehicle s battery The time until full power OFF can be set in Power OFF Timer page 25 8 English ATT indicator Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise Attenuator Turning the volume down quickly Press the ATT button Each time you press the button the Attenuator turns ON and OFF When the Attenuator is ON the ATT indicator blinks System Q Selecting the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button When you press the button once the current sound setting is displayed Each time you press the button the sound setting alternates Sound setting Display atural NATURAL ock ROCK ops POPS Easy EASY op 40 TOP40 azz JAZZ Change each setting value with the Speaker Setting gt page 10 First select the speaker type with the Speaker setting When the value is set up by Audio Control page 9 USER is displayed Audio Control 1 Select the source to adjust Press the SRC button 2 Enter Audio Control mode Press the VOL knob 3 Select t2. Battery cable Yellow A 4 Pin Yellow N The A 7 pin red of the vehicle s ISO connector is connected to the constant power supply and the A 4 pin yellow is linked to the ignition Ignition cable Red A 7 Pin Red Unit Vehicle gt Ba Battery cable Yellow A 4 Pin Yellow w The A 4 pin yellow of the vehicle s ISO connector is not connected to anything while the A 7 pin red is connected to the constant power supply or both the A 7 red and A 4 yellow pins are connected to the constant power supply Ignition cable Red A 7 Pin Red gt Unit Vehicle e Battery cable Yellow A 4 Pin Yellow When the connection is made as in 3 above the unit s power will not be linked to the ignition key For that reason always make sure to turn off the unit s power when the ignition is turned off To link the unit s power to the ignition connect the ignition cable ACC red to a power source that can be turned on and off with the ignition key 28 English Installation Installation Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place Self tapping screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunctio
3. 2 Push the faceplate in until it clicks The faceplate is locked in place allowing you to use the unit 12 English TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON To use the TEL Mute feature you need to hook up the MUTE wire to your telephone using a commercial telephone accessory Refer to Connecting Wires to Terminals page 27 Tuner features KENWOOD AUTO AME ROM REP SEL EE 2 Bo oa fs 1 6 SRC Band display Frequency display ST indicator Tuning Selecting the station 1 Select tuner source Press the SRC button Select the TUNER display 2 Select the band Push the Control knob towards FM or AM Each time you push the knob toward FM it switches between the FM1 FM2 and FM3 bands 3 Tune up or down band Push the Control knob towards ka a or gt gt During reception of stereo stations the ST indicator is ON Preset station number Function of the KDC W534Y Tuning Mode Choose the tuning mode
4. Insulate unconnected wires with vinyl tape or other similar material To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may receive damage or fail to work if you share the wires and or ground them to any metal part in the car After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly f the console has a lid make sure to install the unit so that the faceplate does not hit the lid when closing and opening Mount the unit so that the mounting angle is 30 or less Connecting Wires to Terminals Steering remote control KDC W534 only s To Steering remote REMO CONT Rear left output White Rear right output Red FM AM antenna input L lt O Antenna Cord ISO Antenna Conversion Adaptor Fuse 10A ISO JASO Accessory Wiring harness Accessory To connect these leads refer to E gt the relevant instruction manuals TEL mute wire Brown Connect to the terminal that is grounded when either the telephone rings or during conversation EE To connect the Kenwood d navigation system consult If no connections are made do your navigation manual not let the wire come out from the tab Power control Motor antenna control wire
5. Press the AUTO button Each time you press the button the Tuning mode alternates between the modes shown in he table below Tuning mode Display Operation Auto seek AUTO 1 Automatic search for a station reset station seek AUTO 2 Search in order of the stations in the Preset memory anual MANUAL Normal manual tuning control English 13 Tuner features Station Preset Memory Putting a station in the memory 1 Select the band Push the Control knob towards FM or AM 2 Select the frequency to put in the memory Push the Control knob towards a or gt 3 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the band for Auto Memory Entry Push the Control knob towards FM or AM 2 Open Auto Memory Entry Press the AME button for at least 2 seconds A MEMORY is displayed When 6 stations that can be received are put in the memory Auto Memory Entry closes When the AF Alternative Frequency page 24 is ON only RDS stations are put in the memory When Auto Memory Entry is done in the FM2 band the RDS stations preset in the FM1 band are not put in the memory Likewise when Auto Memory Entry is done in the FM3
6. connect it to the speaker connector in your vehicle 5 Take Connector A on the wiring harness and connect it to the external power connector on your vehicle 6 Connect the wiring harness connector to the unit 26 English 7 Install the unit in your car 8 Reconnect the terminal of the battery 9 Press the reset button If the power is not turned ON or it is ON but will be OFF immediately the speaker wire may have a short circuit or touched the chasis of the vehicle and the protection unction may have been activated Therefore the speaker wire should be checked If your car is not prepared for this special connection system consult your Kenwood dealer Only use antenna conversion adapters ISO JASO when he antenna cord has an ISO plug Make sure that all wire connections are securely made by inserting jacks until they lock completely If your vehicles ignition does not have an ACC position or if the ignition wire is connected to a power source with constant voltage such as a battery wire the power will not be linked with the ignition ie it will not turn on and off along with the ignition If you want to link the unit s power with the ignition connect the ignition wire to a power source that can be turned on and off with the ignition key f the fuse blows first make sure that the wires have not caused a short circuit then replace the old fuse with one with the same rating
7. referring to the section on Connecting Wires to Terminals page 27 English 31 Troubleshooting Guide Disc source The specified disc does not play but another one plays instead The specified CD is quite dirty Clean the CD Y The disc is severely scratched ts Try another disc instead Can t remove disc The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF te The disc can only be removed within 10 minutes of the ACC switch being turned OFF If more than 10 minutes has elapsed turn the ACC switch ON again and press the Eject button The disc won t insert There s already another disc inserted t Press the 4 button and remove the disc Direct Search can t be done v Another function is ON te Turn Random Play or other functions OFF Track Search can t be done WV For the discs folders first or last song ts For each disc folder Track Search can t be done in the backward direction for the first song or in the forward direction for the last song 32 English Audio file source Cannot play an Audio file Y The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on About CDs page 7 J The sound skips when an Audio file is being played The media is scratched or dirty Clean the media referring to the CD cleaning of the section on About
8. Connect either to the power Blue White control terminal when using the optional power amplifier or to VOANDOND the antenna control terminal in Pound the vehicle Battery wire Yellow Ignition wire Red See next page Y A 7 Pin Red A 4 Pin Yellow c Connector A Connector B English 27 Connecting Wires to Terminals Connector Function Guide A WARNING Pin Numbers for Cable Colour Functions Connecting the ISO Connector ISO Connectors The pin arrangement for the ISO connectors depends on the type of vehicle you drive Make sure to make the Yellow Battery proper connections to prevent damage to the unit Blue White ower Control The default connection for the wiring harness is described Red gnition ACC in 1 below If the ISO connector pins are set as described Black Earth Ground in 2 or 3 make the connection as illustrated Connec lease be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc External Power Se id i 1 Default setting The A 7 pin red of the vehicle s ey Front d ISO connector is linked with the ignition and 4 pi j Gray Black Front Righ the A 4 pin a is connected to the constant White Front Le power supply White Black Front Left Ignition cable Red E A 7 Pin Red Green Rear Left Unit 3 Vehicle Green Black Rear Left 2 LE
9. network you may hear the incoming broadcast in bits and snatches Turn OFF the AF function in such a case Function of the KDC W534 Restricting RDS Region Region Restrict Function You can choose whether or not to restrict the RDS channels received with the AF function for a particular network to a specific region Display Setting REG ON The Region Restrict Function is ON REG OFF The Region Restrict Function is OFF If AF function is not restricted to the specified region and network the AF function sets up to search the station with good reception in the same RDS network 24 English In FM reception Monaural Reception You can reduce the noise when stereo broadcasts are received as monaural Display Setting MONO OFF The monaural reception is OFF MONO ON The monaural reception is ON Text Scroll Setting the displayed text scroll Displa Settin SCL MANU Doesn t scroll SCL AUTO Scrolls when the display changes The text scrolled is listed below CD text Folder name File name Song title Artist name Album name Radio text In Standby mode Power OFF Timer Setting the timer to turn this unit s power OFF automatically when Standby mode continues Using this setting can save the vehicle s battery power Display Setting OFF Power OFF Timer function is OFF OFF 20M Turns the power OFF after 20 minutes Original
10. the tag of Ver1 0 1 1 AAC ID3 Tag cannot be displayed Limitation of structure for the file and the folder Maximum number of directory levels 8 Maximum number of folders 100 Maximum number of files per folder 255 Playing order of the Audio file The Audio file plays in the order which is written by writing software You may be able to set the playing order by writing the play sequence numbers such as 01 to 99 at the beginning of the file name Example 3 Folder Oco Ed file L 40 mE o 0 jo RS ET je Playing order Playing order after HO play DO DO HO HO File search Forward file search during HO play Push the Control knob towards gt gt e JE Folder search Forward folder search during PO play Push the Control knob towards FM 31 41 Folder select hen the selection is set to directory 3 and you want to skip to the folder 2 at the same level Push the Control knob towards ka a hen the selection is set to directory 3 moves the level up by folder select Push the Control knob towards AM About CDs Handling CDs Do not touch the recording surface of the CD CD R and CD RW are easier to damage than a normal music CD Use a CD R or a CD RW after reading the caution items on the package etc Do not stick tape etc on the CD or use a CD with tape stuck on it When using a new CD If the CD ce
11. CDs page 7 The recording condition is bad tse Record the media again or use another media The Audio file track time isn t displayed correctly v ts There are times when it isn t displayed correctly according to the Audio file recording conditions Supreme does not take effect when it is turned ON Little high frequency component te Supreme would not take effect with songs with little high frequency component v Songs that have not been encoded at bit rates at 96 kbps or less fs 2 32k 44 1 k 48 kHz or those that have been encoded at a variable bit rate cannot be decoded to reproduce their high frequency components m The messages shown below display your systems condition TOC ERR The CD is quite dirty The CD is upside down The CD is scratched a lot Clean the CD and load it correctly E 05 The CD is upside down Load the CD correctly E 99 The unit is malfunctioning for some reason x Press the reset button on the unit If the E 99 code does not disappear consult your nearest service center READING The unit is reading the data on the disc N Blink The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center PROTECT The speaker wire has a short circuit or touches the c
12. KENWOOD CD RECEIVER KDC W534 KDC W534Y INSTRUCTION MANUAL Kenwoo d Corporation B64 3266 00 00 EW EN E2W E2N Contents Safety precautions 3 Menu system 21 enu System Notes 4 Touch Sensor Tone anual Clock Adjustment About AAC MP3 and WMA 6 Synchronize Clock DSI Disabled System Indicator About CDs 7 Selectable Illumination General features 8 Display Illumination Control Supreme Setting Power ews Bulletin with Timeout Setting Selecting the Source Local Seek Volume Tuning Mode KDC W534 Attenuator AF Alternative Frequency System Q Restricting RDS Region Region Restrict Audio Control Function Audio Setup Auto TP Seek Speaker Setting onaural Reception Switching Display Text Scroll Dimmer Control Power OFF Timer Theft Deterrent Faceplate CD Read Setting TEL Mute Demonstration mode Setting Tuner features 13 Accessories Installation Procedure 26 Tuning C 2 Wi 1 inal 2 Tuning Mode KDC W534Y onnecting Wires to Terminals 7 Station Preset Memory E Auto Memory Entry Installation 29 Preset Tuni 7 AS Removing the Unit 30 RDS features 15 i r Traffic Information Troubleshooting Guide 35 Radio Text Scroll es de PTY Program Type Specifications 34 Program Type preset Changing Language for PTY Function CD player features 18 Playing CD amp Audio file Fast Forwarding and Reversing Track File Search Folder Search Track File Folder Repeat Scan Play Random Play Folde
13. LE Track number amp Play time P TIME Clock CLOCK In Standby mode Information Display Source name SRC NAME Clock CLOCK 3 Exit Switching Display mode Press the Control knob If the contents of the information cannot be displayed Play time is displayed When you select the clock display the display setting of each source will be changed to the clock display Album name cannot be displayed in WMA file Dimmer Control You can lower the brightness of the display by using the dimmer function Press the DIM button for at least 1 second Each time you press the button for 1 second the Dimmer control turns ON or OFF When the Dimmer control is ON DIM ON is displayed English 11 General features Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you helping to deter theft Removing the Faceplate 1 Press the Release button Drop open the faceplate 2 Drawing the faceplate to left side pull it to forward and remove it The faceplate is a precision piece of equipment and can be damaged by shocks or jolts Keep the faceplate in its faceplate case while detached Do not expose the faceplate and the faceplate case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Faceplate 1 Align the shaft on the unit with the depression on the faceplate
14. RAC REP OFF REP OFF In Audio file source Repeat play Display File Repeat FILE REP Folder Repeat FOLD REP OFF REP OFF Scan Play Playing the first part of each song on the disc or Audio file folder you are listening to and searching for the song you want to hear 1 Start Scan Play Press the SCAN button TRAC SCN FILE SCN is displayed 2 Release it when the song you want to listen to is played Press the SCAN button Random Play Play all the songs on the disc or Audio file folder in random order Press the RDM button Each time you press the button Random Play turns ON or OFF When the Random mode is ON DISC RDM FOLD RDM is displayed When you push the Control knob toward gt the next random song starts English 19 CD player features Function of Audio file Folder Select Quickly selecting the folder you want to hear 1 Enter Folder Select mode Press the F SEL button FOLD SEL is displayed During Select mode the folder information is displayed as shown below Folder name display Displays the current folder name 2 Select the folder level Push the Control knob towards FM or AM With the FM of the Control knob you move 1 level down and with the AM of the Control knob 1 level up Selecting a folder in the same level Push the Control knob towards ka a or gt gt With the ka a of the Control knob you move to the previous folder and with the g
15. Traffic least 2 seconds Information function is turned ON the frequency changes to an FM station During reception of traffic information the adjusted volume is automatically remembered and the next time the audio changes to traffic information the volume automatically becomes the remembered volume When the Display Illumination Control page 22 is set to OFF the display may black out while scrolling English 15 Function of the KDC W534 RDS features PTY Program Type Selecting the Program Type and searching for a station 1 Enter PTY mode Press the Control knob During PTY mode the PTY indicator is ON This function cannot be used during a traffic bulletin or AM reception 2 Select the Program Type Push the Control knob towards FM or AM Each time you push the knob the Program Type alternates between the program types shown in he table below No Program Type Display 1 usic MUSIC 2 Speech SPEECH 3 ews NEWS 4 Current Affairs AFFAIRS 5 nformation INFO 6 Sport SPORT i Education EDUCATE 8 rama DRAMA 9 Culture CULTURE 0 Science SCIENCE 1 Varied VARIED 2 Pop Music POP M 3 Rock Music ROCK M 4 Easy Listening Music EASY M 5 Light Classical LIGHT M 6 Serious Classical CLASSICS 7 Other Mu
16. band RDS stations preset in FM1 or FM2 are not put in the memory 14 English Preset Tuning Recalling the stations in the memory 1 Select the band Push the Control knob towards FM or AM 2 Recall the station Press the desired 1 6 button Function of the KDC W534 RDS features KENWOOD Control knob A Gey RDS indicator Tlindicator PTY indicator Traffic Information Receiving other traffic information stations oe een a ee Push the Control knob towards 4 4 or Changing to traffic information automatically gt when a traffic bulletin starts even when you are d not listening to the radio Traffic information can be switched when it is on the Tuner Source However you cannot switch the Traffic information during reception of the Traffic bulletin switched from the source other than the Tuner Press the TI button Each time you press the button the Traffic information function turns ON and OFF When traffic information is ON TI indicator is ON When a traffic information station is not being received the Tl indicator blinks When a traffic bulletin starts TRAFFIC is displayed and the audio changes to traffic Radio Text Scroll information Scrolling the displayed radio text Push the Control knob toward FM for at During reception of an AM station when the
17. ble Accessory Removal tool 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General The power does not turn ON The fuse has blown After checking for short circuits in the wires replace the fuse with one with the same rating The memory is erased when the ignition is turned OFF Y The ignition and battery wire are incorrectly connected t Connect the wire correctly referring to the section on Connecting Wires to Terminals page 27 J The TEL mute function does not work The TEL mute wire is not connected properly t Connect the wire correctly referring to the section on Connecting Wires to Terminals page 27 The TEL mute function turns ON even though the TEL mute wire is not connected v The TEL mute wire is touching a metal part of the car t Pull the TEL mute wire away from the metal part of the car J Even if Loudness is turned ON high pitched tone isn t compensated for v Tuner source is selected te High pitched tone isn t compensa
18. de for news bulletin When the News Bulletin Interrupt function is ON the tuner changes to an FM station In Tuner mode Local Seek Only stations whose reception is good are searched in auto seek tuning Display Setting LO S OFF The local seek function is OFF LO S ON The local seek function is ON Function of the KDC W534 In Tuner mode Tuning Mode Sets the tuning mode Tuning mode Display Operation Auto seek AUTO 1 Automatic search for a station Preset station seek AUTO 2 Search in order of the stations in the Preset memory Manual MANUAL Normal manual tuning control English 23 Menu system Function of the KDC W534 AF Alternative Frequency When the reception is poor automatically alternate to another frequency broadcasting the same program in the same RDS network with better reception Function of the KDC W534 Auto TP Seek When the TI function is ON and the reception is poor while listening to a traffic information station another traffic information station with better reception will be searched for automatically Displa Settin AF ON The AF function is ON Display Setting AF OFF The AF function is OFF ATPS ON The Auto TP Seek Function is ON ATPS OFF The Auto TP Seek Function is OFF When the AF function is ON the RDS indicator is ON When no other stations with stronger reception are available for the same program in the RDS
19. e knob it alternates between BEEP ON or BEEP OFF Select 1 of them as the setting You can continue by returning to step 2 and setting other items 4 Exit Menu mode Press the MENU button When other items those applicable to the basic operation method above are displayed their setting content chart is entered Normally the setting listed at the top of the chart is the original setting Also the explanation for items that are not applicable Manual Clock Adjustment etc are entered step by step English 21 Menu system In Standby mode Touch Sensor Tone Setting the operation check sound beep sound ON OFF DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Display Setting Display Setting DSI ON LED flashes BEEP ON Beep is heard DSI OFF LED OFF BEEP OFF Beep canceled In Standby mode In Standby mode Manual Clock Adjustment You can do this adjustment when the lt Synchronize Clock page 22 is set as OFF 1 Select Clock Adjustment mode Push the Control knob towards FM or AM Select the CLK ADJ display 2 Enter Clock Adjust mode Press the Control knob for at least 1 second The clock display blinks 3 Adjust the hours Push the Control knob towards FM or AM Adjust the minutes Push the Control knob towards ka a or gt gt 4 Exit Clock adjustment mode Pre
20. excessive force to the open aceplate or place objects on it Doing so will cause damage or breakdown Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit Do Not Load 8 cm 3 in CDs in the CD slot If you try to load a 8 cm 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit Lens Fogging When you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging this condesnation on the lens may not allow CDs to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer The AAC logo is trademark of Dolby Laboratories English 3 Notes If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they work with your model and in your area If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Reset button The characters which can be displayed by this unit are A Z 0 9 9 amp lt gt A The RDS feature won t work where the service is no
21. hassis of the vehicle and then the protection function is activated Wire or insulate the speaker cable properly and press the reset button NA FILE An Audio file is played with a format that this unit can t support p COPY PRO A copy protected file is played eb c DEMO MODE The Demonstration mode has been selected x The Demonstration mode Setting page 25 is ON Turn it OFF English 33 Specifications Specifications subject to change without notice FM tuner section Frequency range 50 kHz space 87 5 MHz 108 0 MHz Usable sensitivity S N 26dB 07 uV 75 0 Quieting Sensitivity S N 46dB 1 6 uV 750 Frequency response 3 0 dB 30 Hz 15 kHz Signal to Noise ratio MONO 65 dB Selectivity DIN 400 kHz gt 80 dB Stereo separation 1 kHz 35 dB MW tuner section Frequency range 9 kHz space 531 kHz 1611 kHz Usable sensitivity S N 20dB 25 UV LW tuner section Frequency range 153 kHz 281 kHz Usable sensitivity S N 20dB 45 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz 0 01 96 Signal to Noise ratio 1 kHz 105 dB Dynamic range 93 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 34 Engli
22. he Audio item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Audio item Turn the VOL knob Adjustment Item Display Range Bass level BAS L 8 8 Middle level MID L 8 8 Treble level TRE L 8 8 Balance BAL Left 15 Right 15 Fader FAD Rear 15 Front 15 Exit Audio Control mode Volume control mode 5 Exit Audio Control mode Press any button Press a button other than the VOL knob and ATT button English 9 General features Audio Setup Setting the Sound system such as Volume offset and Loudness 1 Select the source to adjust Press the SRC button 2 Enter Audio Setup mode Press the VOL knob for at least 1 second 3 Select the Audio Setup item to adjust Press the VOL knob Each time you press the knob the item to be adjusted alternates between the items shown in the table below 4 Adjust the Audio setup item Turn the VOL knob Adjustment Item Display Range Volume offset V OFF 8 0 Loudness LOUD OFF ON Volume offset Sets each sources volume as a difference from the basic volume Loudness Compensates for low and high tones during low volume When Loudness is ON LOUD indicator is ON 5 Exit Audio Setup mode Press the VOL knob for at least 1 second 10 English Speaker Setting Fine tuni
23. ide part and cause damage When a disc is inserted the IN indicator is ON 18 English When a disc is inserted Press the SRC button Select the CD display Pause and play Press the Control knob Each time you press the knob the audio pauses or plays Eject the disc 1 Drop open the faceplate Press the Release button 2 Eject the disc Press the 4 button 3 Press the faceplate on the left side and return it to its former position Fast Forwarding and Reversing Fast Forwarding Hold down toward gt gt with the Control knob Release your finger to play the disc at that point Reversing Hold down toward kaa with the Control knob Release your finger to play the disc at that point There is no sound while the Audio file is being searched You cannot fast Forwarding and Reversing while AAC file is being played Track File Search Searching for a song on the disc or in the Audio file folder Push the Control knob towards ka a or gt gt Function of Audio file Folder Search Selecting the folder recorded on the Audio file media Push the Control knob towards FM or AM Track File Folder Repeat Replaying the song or Audio file folder you are listening to Press the REP button Each time you press the button the Repeat Play alternates between the modes shown in the tables below In CD source Repeat play Display Track Repeat T
24. n for example the sound may skip Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off 1 Refer to the section lt Removing the hard rubber frame gt page 30 and then remove the hard rubber frame 2 Drop open the faceplate by pressing the Release button 3 Tighten the screw 92 x 5 mm Accessory and bracket AccessoryG in the hole shown on the diagram 4 Tighten the screw 22 x 5 mm Accessory and bracket Accessory amp in the hole shown on the diagram Never insert the screws in any other screw hole than the one specified If you screw them in another hole it will contact and may cause damage to the mechanical parts inside the unit English 29 Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner 30 English Removing the Unit 1 Refer to the section Removing the hard rubber frame page 30 and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown Screw M4X8 commercially availa
25. nd outputs a loud noise causing damage to the speaker The files with copy protection cannot be played The settings of your encoding software and the environment in which it is used may now allow you to play or view specific audio files The unit may not be compatible with upgrade of compression format standard and additional specifications Playable AAC file m4a file encoded by AAC LC format Refer to http www Kenwood mediamanager jp for the details Playable MP3 file MPEG 1 2 Audio Layer 3 file Transfer bit rate 8 320 kbps Sampling frequency 8 11 025 12 16 22 05 24 32 44 1 48 kHz Playable WMA file The file in accordance with Windows Media Audio Except for the file for Windows Media Player 9 or after which applies the new functions Transfer bit rate 48 192 kbps Sampling frequency 32 44 1 48 kHz Playable media CD ROM CD R CD RW CD RW discs which are quick formatted by the writing software cannot be used When recording to the maximum media capacity at once the writing software is set to Disc at once Playable disc format ISO 9660 Level 1 2 Joliet Romeo Long file name 6 English The maximum number of characters for display File Folder name 64 characters MP3 ID3 Tag WMA Contents property AAC song information 30 characters File Folder name is the number of the characters including the extensions MP3 ID3 Tag can only display
26. ng so that the System Q value is optimal when setting the speaker type 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Speaker Setting mode Press the VOL knob 3 Select the Speaker type Turn the VOL knob Each time you turn the knob the setting alternates between the settings shown in the able below Speaker type Display OFF SP OFF For 5 amp 4 in speaker SP 5 4 For 6 amp 6x9 in speaker SP 6 9 6 For the OEM speaker SP OEM 4 Exit Speaker Setting mode Press the VOL knob Switching Display Changing the information displayed 1 Enter Switching Display mode Press the Control knob for at least 1 second DISP SEL is displayed 2 Select the Display item Push the Control knob towards ka a or gt gt In Tuner source KDC W534 Information Display Program Service name or Frequency FREQ PS FM Radio text Program Service name or R TEXT Frequency FM Frequency MW LW FREQ Clock CLOCK In Tuner source KDC W534Y Information Display Frequency FREQ Clock CLOCK In CD source Information Display Disc title D TITLE Track title T TITLE Track number amp Play time P TIME Clock CLOCK In Audio file source Information Display Song title amp Artist name LE Album name amp Artist name ALBUM Folder name FOLDER File name FI
27. nter hole or outside rim has burrs use the CD only after removing the burrs with a ballpoint pen etc CD accessories Do not use disc type accessories CD cleaning Clean from the center of the disc and move outward Nd Removing CDs When removing CDs from this unit pull them out horizontally CDs that cannot be used CDs that are not round cannot be used CDs with coloring on the recording surface or CDs hat are dirty cannot be used This unit can only play the CDs with dies Ges dl This unit may not correctly play discs which do not have the mark You cannot play a CD R or CD RW that has not been finalized For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual CD storage Do not place CDs in direct sunlight On the seat or dashboard etc or where the temperature is high Store CDs in their cases English 7 General features E Sa KENWOOD ATT DIM SU Control knob Release button Q Clock display 9 Cr asc asmenu o nee FSEL AM e es 5 s Ge 5 nor SRC LOUD indicator Power Turning ON the Power Press the SRC button Turning OFF the Power Press the SRC button for at least 1 second Selecting the Source Press the SRC button
28. or EU countries that have adopted separate waste collection systems Products with the symbol crossed out wheeled bin cannot be disposed as household waste Old electrical and electronic equipment EN should be recycled at a facility capable of handling these items and their waste byproducts Contact your local authority for details in locating a recycle facility nearest to you Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment The marking of products using lasers Except for some areas CLASS 1 LASER PRODUCT The label is attached to the chassis case and says that the component uses laser beams that have been classified as Class 1 It means that the unit is utilizing laser beams that are of a weaker class There is no danger of hazardous radiation outside the unit English 5 About AAC MP3 and WMA The playable AAC MP3 WMA file hereafter called Audio file and the media format has the following limitation The Audio file which is not conforming to the specification may not play normally or the file and folder names may not display correctly Playable Audio file AAC MP3 WMA A Attach the correct extension for the Audio file AAC MAA MP3 MP3 WMA WMA Do not attach the extensions to files other than the Audio file If the extension is attached the file which is not the Audio file will play a
29. r Select Text Title Scroll 2 English Safety precautions AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals Attach the panel while you are on the vehicle The panel lock arm appears when the panel is removed Therefore the panel must be attached while the electrical system of the car is operating ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not place the faceplate and the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the erminals of the unit or faceplate with your ingers Do not subject the faceplate to excessive shock as itis a piece of precision equipment When replacing a fuse only use a new fuse with he prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction Do not apply
30. ram Type page 16 2 Recall the Program Type Press the desired 1 6 button Changing Language for PTY Function Selecting the Program Type display language 1 Enter PTY mode Refer to lt PTY Program Type gt page 16 2 Enter Changing Language mode Press the TI button 3 Select the language Push the Control knob towards FM or AM Each time you push the knob the language alternates between the languages shown in the table below Language Display English ENGLISH French FRENCH German GERMAN 4 Exit Changing Language mode Press the TI button English 17 CD player features KENWOOD Release button SCAN Track number RDM REP F SEL SRC Play time IN indicator Playing CD amp Audio file When there is no disc inserted 1 Drop open the faceplate Press the Release button 2 Insert a disc 3 Push the faceplate on the left side and return it to its former position A When the faceplate has been dropped open it might interfere with the shift lever or other vehicle function If this happens pay attention to safety and move the shift lever or take an appropriate action to remove the obstacle then operate the unit Do not use the unit with the faceplate in the open condition If it s used in the open position dust can enter the ins
31. s their high frequency region to approach the sound quality of equivalents of these files encoded at a high bit rate Processing is optimized for the compression format used AAC MP3 or WMA and adjustment is made for the bit rate used Display Setting SPRM ON Plays sound using the Supreme function SPRM OFF Plays the original sound stored in the audio file The sound effect may be imperceptible depending on the relationship between the audio file format and setting Function of the KDC W534 News Bulletin with Timeout Setting The tuner automatically changes when a news bulletin starts even if the radio is not being listened to Also you can set the time interval when interruption is prohibited Display and Setting NEWS OFF NEWS 00M NEWS 90M When you set NEWS 00M NEWS 90M the News Bulletin Interrupt function is ON When the News Bulletin is ON the NEWS indicator is ON When the news bulletin starts NEWS is displayed and the tuner changes to the news bulletin If you choose the 20MIN setting further news bulletins will not be received for 20 minutes once the first news bulletin is received The news bulletin volume is the same level that was set for Traffic Information page 15 This news bulletin function is only available if the desired station sends PTY code for news bulletin or belongs to Enhanced Other Network Network sending PTY co
32. setting OFF 40M Turns the power OFF after 40 minutes OFF 60M Turns the power OFF after 60 minutes In Standby mode CD Read Setting When there is a problem with playing a CD with special format this setting plays the CD by force Display Setting CD READT Play CD and Audio file CD READ2 Play CD by force Setting CD READ2 cannot play Audio file Some music CDs may not play even in the CD READ2 mode In Standby mode Demonstration mode Setting Sets the demonstration mode 1 Select the Demonstration mode Push the Control knob towards FM or AM Select the DEMO display 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Each time you press the knob at least 2 seconds the Demonstration mode alternates between the settings shown in the table below Display Setting DEMO ON The Demonstration mode function is ON DEMO OFF Exit Demonstration mode Normal mode English 25 Accessories Installation Procedure Accessories 1 ae 2 O E L DP A 1 po UN 2 5 A o o OL E 1 1 Installation Procedure 1 To prevent short circuits remove the key from the ignition and disconnect the O terminal of the battery 2 Make the proper input and output wire connections for each unit 3 Connect the wire on the wiring harness 4 Take Connector B on the wiring harness and
33. sh WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files Audio section Maximum output power 50 W x 4 KDC W534Y 45 W x 4 KDC W534 Output power DIN 45324 B 14 4V 30 W x 4 KDC W534Y 28 W x 4 KDC W534 Speaker impedance 4 80 Tone action Bass 100 Hz 8 dB Middle 1 kHz 8 dB Treble 10 kHz 8 dB Preout level Load during disc play 2000 mV 10 kO Preout impedance lt 6000 General Operating voltage 11 16V allowable 144V Current consumption 10 A Installation Size W x H x D 182x 53 x 155 mm Weight 1 40 kg KENWOOD
34. sic OTHER M 8 Weather WEATHER 9 Finance FINANCE 20 Children s programs CHILDREN 21 Social Affairs SOCIAL 22 Religion RELIGION 23 hone In PHONE IN 24 rave TRAVEL 25 Leisure LEISURE 26 azz Music JAZZ 27 Country Music COUNTRY 28 ational Music NATION M 29 Oldies Music OLDIES 30 Folk Music FOLK M 31 Documentary DOCUMENT 16 English Speech and Music include the Program type shown below Music No 12 17 26 30 Speech No 3 11 18 25 31 You can put the Program Type in the 1 6 button memory and for quick recall Refer to the lt Program Type preset gt page 16 You can change the display language Refer to lt Changing Language for PTY Function gt page 17 3 Search for the selected Program Type station Push the Control knob towards ka a or gt When you want to search for other stations push aa or gt gt of the Control knob again When the selected Program Type is not found NO PTY is displayed Select another Program Type 4 Exit PTY mode Press the Control knob Program Type preset Putting the Program Type in the Preset button memory and quick recall Presetting the Program Type 1 Select the Program Type to preset Refer to PTY Program Type page 16 2 Preset the Program Type Press the desired 1 6 button for at least 2 seconds Recalling the preset Program Type 1 Enter PTY mode Refer to PTY Prog
35. ss the MENU button Function of the KDC W534 In Standby mode Synchronize Clock Synchronizing the RDS station time data and this unit s clock Displa Settin SYNC ON Synchronizes the time SYNC OFF Adjust the time manually It takes 3 to 4 minutes to synchronize the clock 22 English Selectable Illumination Selecting the button illumination color as green or red Display Setting KEY RED The illumination color is red KEY GRN The illumination color is green Display Illumination Control This function turns off the display when you perform no operation for 5 seconds This function is effective when you are driving at night Display Setting DISP ON Keeps the display on DISP OFF Turns off the display when you perform no operation for 5 seconds Set the Display Illumination Control when the lt Demonstration mode Setting gt page 25 is set to OFF When the display is off pressing any key will turn on the display When the display is off you cannot perform any operation except for the following Volume Attenuator Selecting the source Ejecting the disc Turning off the power Dimmer Control During function control such as the Menu System the display stays on In Audio file source Supreme Setting When AAC MP3 or WMA files encoded at a low bit rate less than 96kbps fs 32k 44 1k 48kHz are played this function restore
36. t i of the Control knob to the next folder Returning to the top level Press the 3 button Scrolling the folder name display Push the Control knob toward FM for at least 2 seconds 3 Decide the folder to play Press the Control knob The Folder Select mode releases and the Audio file in the folder being displayed plays Cancelling the Folder Select mode Press the F SEL button 20 English Text Title Scroll Scrolling the displayed CD text or Audio file text Push the Control knob toward FM for at least 2 seconds When the Display Illumination Control page 22 is set to OFF the display may black out while scrolling Menu system KENWOOD MENU Menu display SRC ALES NEWS indicator RDS indicator Menu System Setting beep sound during operation etc functions The Menu system basic operation method is explained here The reference for the Menu items and their setting content is after this operation explanation 1 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 2 Select the menu item Push the Control knob towards FM or AM Example When you want to set the beep sound select the BEEP display 3 Set the menu item Push the Control knob towards ka a or gt gt Example When you select BEEP each time you push th
37. t supported by any broadcasting station The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the illustrations on the display may be inapplicable Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe it again with a clean soft dry cloth Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters 4 English Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a clean soft dry cloth Before using this unit for the first time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 25 This Product is not installed by the manufacturer of a vehicle on the production line nor by the professional importer of a vehicle into an EU Member State Information on Disposal of Old Electrical and Electronic Equipment applicable f
38. ted for when in Tuner source No sound can be heard or the volume is low The fader or balance settings are set all the way to one side t Center the fader and balance settings The input output wires or wiring harness are connected incorrectly t Reconnect the input output wires or the wiring harness correctly See the section on lt Connecting Wires to Terminals gt page 27 The values of Volume offset are low t Turn up the Volume offset referring to the section on Audio Setup page 10 The sound quality is poor or distorted One of the speaker wires is being pinched by a screw in the car Check the speaker wiring The speakers are not wired correctly te Reconnect the speaker wires so that each output terminal is connected to a different speaker The Touch Sensor Tone doesn t sound The preout jack is being used ts The Touch Sensor Tone can t be output from the preout jack Even though Synchronize Clock is ON the clock can t be adjusted The received RDS station isn t sending time data t Receive another RDS station J The display blacks out while scrolling Display Illumination Control is set to OFF te Refer to Display Illumination Control page 22 Tuner source Radio reception is poor The car antenna is not extended t Pull the antenna out all the way The antenna control wire is not connected t Connect the wire correctly
Download Pdf Manuals
Related Search