Kenwood KDC-MP528 Car Stereo System User Manual
Contents
1. Media Manager is recorded in the CD ROM attached to this unit Refer to the attached installation manual for the installation method of Media Manager Refer to the user s manual recorded in the installation CD ROM and Help of Media Manager for the operation method of Media Manager The unit can play CD hereafter called ACDrive disc created by Media Manager Refer to the following site for the updated information of Media Manager http www kenwood mediamanager jp Contact Kenwood for the function and operation of the Media Manager Media Manager is a product of PhatNoise 6 English AWarning ACAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure In compliance with Federal Regulations following are reproductions of labels on or inside the product relating to laser product safety KENWOOD CORPORATIO 2967 3 ISHIKAWA MACH HACHIOJI SHI TOKYO JAPAN KENWOOD CORP CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS NO 21 CFR 1040 10 CHAPTER 1 SUBCHAPTER J Location Bottom Panel FCC WARNING This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose the authority to operate this equipment if2. ALBUM By album FOLDER By the folder recorded in Disc The category information of each song is the data registered in Media Manager when ACDrive disc is being generated The announcement when the mode is switched can be canceled by lt Voice Index gt page 28 The advancement of the play mode information can be selected by AM and FM keys Function of the KDC X589 Function of the ACDrive disc Letter Seek The song in which you want to play can be searched by selecting the initial of Genre name Artist name or Album name 1 Enter the Letter Seek mode Press the S MODE button for at least 1 second It doesn t function when lt Disc Random Play gt page 19 is ON This function is available only when the Play mode is set Genre Artist or Album Canceling the Letter Seek Press the S MODE button 2 Start the Letter Seek Push the Control knob to ka a or gt gt The initial of Genre name Artist name or Album name is displayed and read out by the order The announcement of the initial can be canceled by lt Voice Index gt page28 When the Control knob is pushed to the reverse of ke or PI while Letter Seek the initial is displayed and read by the reversed order When the Letter Seek is started it cannot be cancelled 3 Select the song to play Press the Control knob when the initial of the song you are searching is displayed and read The selected initial grou
3. TITLE switches as shown below Album name Genre Speaker type Display Frequency FREQ OFF SP OFF Clock CLOCK For 5 amp 4 in speaker SP 5 4 For 6 amp 6x9 in speaker SP 6x9 6 In SIRIUS tuner source For the OEM speaker SP OEM invarmarion Display 4 Exit Speaker Setting mode ea eee Ch AME Press the VOL knob song title SONG Artist name ARTIST Composer name COMPOSER Category name CATEGORY P a Label name LABEL Switching Display A COMMENT Switching the information displayed Band amp Channel number CH NUM Clock CLOCK 1 Enter Switching Display mode Press the Control knob for at least 1 second DISP SEL is displayed 2 Select the Display item Push the Control knob to ka a or gt gt In Tuner source Information Display Station name or Frequency SNPS Frequency FREQ Clock CLOCK In CD amp External disc source Information Display Disc title D TITLE Track title T TITLE Track number amp Play time P TIME Disc name DNPS Clock CLOCK 12 English In Auxiliary input source Standby source Information Display Source name SRC NAME Clock CLOCK 3 Exit Switching Display mode Press the Control knob When LX AMP is connected the item setup by the Display mode of LX AMP is displayed KDC X589 only If the contents of the information cannot be displayed Play time or Frequency is displayed
4. 1 6 button CD Audio file External disc control features O V excelon systeme s KENWOOD 24er Dac aa ov ete aise i coy H Radio O 223 OD Dp Wa se 20 S MODE SCAN RDM 3 REP F SEL M RDM SRC Controlknob amp D RDM SCAN RDM 3 REP Track number IN indicator Playing CD amp Audio file When there is no disc inserted 1 Open the panel Press the 4 button 2 Insert a disc A When the faceplate has been slid open it might interfere with the shift lever or something else If this happens pay attention lever or take an appropri unit Insert the disc horizonta Disc as you push down Disc o safety and move the shift iate action then operate the to the slot If you insert the he Disc it may scratch the Refer to lt About AAC M 3 and WMA gt page8 for the Audio file by models which can be played The announcement when selecting the folder can be canceled by lt Voice Index gt page28 during the play of the ACDrive When a disc is inserted the IN indicator is ON FOLDER P LIST GENRE ALBUM ARTIST Play mode a F SEL M RDM Control knob Track time Disc number When a disc is inserted Press the SRC button Select the CD display Pause and play Press the
5. Maximum number of files per folder KDC X589 4096 KDC MP5028 MP528 255 Playing order of the Audio file The Audio file is played in the order which is written by writing soft You may be able to set the playing order by writing the play sequence numbers such as 01 to 99 at the beginning of the file name Example co 4 dO FE yo 0 ho Jo AI ye Playing order Playing order after play AO DO HO DO File search Forward file search during play Push the Control knob to bb J Folder search Forward folder search during play Push the Control knob to FM 3 41 Folder select When it is set to directory skip to the folder before the same level by folder select Push the Control knob to ka When it is set to directory 2 makes the level up by folder select M C Q1 Folder ed Audio file Push the Control knob to A General features leXcelon System E s 4 0V SIRs KENWOOD 248i DAC REP ESEL MAROM Ee Ce Ce Ce led E Ce ATT Releasebutton VOL Q MENU SRC Controlknob ANG SIRIUS ATT Release button VOL Q MENU SRC Controlknob ANG LOUD Power Turning ON the Power Press the SRC button Turning OFF the Power ATT indicator
6. Press the SRC button for at least 1 second Selecting the Source Press the SRC button Source required Display SIRIUS tuner Optional accessory SIRIUS Tuner or HD Radio Optional accessory TUNER or HD RADIO O p External disc Optional accessory CD CH Auxiliary input AUX Auxiliary input Optional accessory AUX EXT Standby Illumination only mode STANDBY Function of the KDC MP5028 MP528 LOUD indicator Volume Increasing Volume Turn the VOL knob clockwise Decreasing Volume Turn the VOL knob counterclockwise Attenuator Turning the volume down quickly Press the ATT button Each time the button is pressed the Attenuator turns ON and OFF When it s ON the ATT indicator blinks English 9 General features System Q You can recall the best sound setting preset for different types of music 1 Select the source to set Press the SRC button 2 Select the Sound type Press the Q button Each time the button is pressed the sound setting switches Sound setting Display User memory USER Rock ROCK Pops POPS Easy EASY Top 40 TOP40 Jazz JAZZ Natural NATURAL User memory The values set on the lt Audio Control gt page 10 Each setting value is changed with the lt Speaker Setting gt page 12 First select the speaker type with the Speaker setting Audio Cont
7. use it after removing them with a ball pen etc CD accessories Don t use disc type accessories CD cleaning Clean from the center of the disc and move outward Wel Removing CDs When removing CDs from this unit pull them out horizontally CDs that can t be used CDs that aren t round can t be used CDs with coloring on the recording surface or that are dirty can t be used It may not correctly play discs which do not have the mark A CD R or CD RW that hasn t been finalized can t be played For the finalization process refer to your CD R CD RW writing software and your CD R CD RW recorder instruction manual CD storage Don t place them in direct sunlight On the seat or dashboard etc and where the temperature is high Store CDs in their cases English 7 About AAC MP3 and WMA The playable AAC MP3 WMA file hereafter called Audio file and the media format has the following limitation The Audio file which is out of the specification may not able to be played normally or the file and folder names may not be displayed correctly A Attach the correct extension for the Audio file AAC M4A MP3 MP3 WMA WMA Do not attach the extensions to the other files besides the Audio file If it is attached the file which is not the Audio file will be played and outputs the loud noise and then the speaker will be damaged The files with copy protection cannot be p
8. 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Auxiliary input display setting mode Push the Control knob to FM or AM Select the NAME SET display 4 Enter Auxiliary input display setting mode Press the Control knob for at least 1 second The presently selected Auxiliary input display is displayed 5 Select the Auxiliary input display Push the Control knob to ka a or gt gt Each time the button is pressed the display switches as shown below AUX AUX EXT DVD PORTABLE GAME VIDEO TV 6 Exit Auxiliary input display setting mode Press the MENU button When operation stops for 10 seconds the name at that time is registered and the Auxiliary input display setting mode closes The Auxiliary Input Display can be set only when the built in auxiliary input or the auxiliary input of optional KCA S210A is used KDC MP5028 MP528 only Text Scroll Setting the displayed text scroll Display Setting SCL AUTO Repeats scroll SCL MANU Scrolls when the display changes The text scrolled is shown below CD text Folder name File name Song title Artist name Album name MD title Text for the SIRIUS tuner source HD Radio source including Channel name etc Function of the KDC MP5028 KDC MP528 In Standby mode Built in Auxiliary input Setting Set the Built in Auxiliary Input function Di
9. Call Push the Contol knob to FM or AM Select the CALL display 6 Call up the Audio Preset Press the Control knob for at least 2 seconds The CALL display blinks 1 time 7 Exit Menu mode Press the MENU button The User memory of lt System Q gt page 10 is changed to the value which was recalled The source tone memory item of lt Audio Control gt page 10 is changed to the value which was recalled by the selected source In Standby mode Demonstration mode Setting Sets the demonstration mode 1 Select the Demonstration mode Push the Control knob to FM or AM Select the DEMO display 2 Set the Demonstration mode Press the Control knob for at least 2 seconds Each time the knob is pressed at least 2 seconds the Demonstration mode switches as shown below Display Setting DEMO ON The Demonstration mode function is ON DEMO OFF Exit Demonstration mode Normal mode English 29 Basic Operations of remote Ia e FM AM 2 ZONE t0 9 Loading and Replacing the battery Use two AA size batteries Slide the cover while pressing downwards to remove it as illustrated Insert the batteries with the and poles aligned properly following the illustration inside the case AWARNING Store unused batteries out of the reach of children Contact a doctor immediately if the battery is accidentally swallowed A Do not se
10. Code is required when it s removed from the vehicle personalizing this unit is by using the Security Code is a help in preventing theft The setup Security Code can be done when the lt Demonstration mode Setting gt page 29 is set as OFF When the Security Code function is activated the code can t be changed and the function can t be released Note the Security Code can be set as the 4 digit number of your choice 1 Enter Standby Press the SRC button Select the STANDBY display 2 Enter Menu mode Press the MENU button for at least 1 second When MENU is displayed SECURITY is displayed 3 Enter Security Code mode Press the Control knob for at least 1 second When ENTER is displayed CODE is displayed 4 Select the digits to enter Push the Control knob to ka a or gt gt 5 Select the Security Code numbers Push the Control knob to FM or AM 6 Repeat steps 4 and 5 and complete the Security Code 7 Confirm the Security Code Press the Control knob for at least 3 seconds When RE ENTER is displayed CODE is displayed 8 Do the step 4 through 7 operation and reenter the Security Code APPROVED is displayed The Security Code function activates When the wrong Code is entered in steps 4 through 6 repeat from step 4 Press the Reset button and when it s removed from the battery power source 1 Turn the power ON 24 English 2 Do the step 4 through 7 operation and ent
11. Control knob Each time the knob is pressed it pauses and plays Eject the disc 1 Eject the disc Press the 4 button 2 Return the panel to the original position Press the 4 button English 17 CD Audio file External disc control features Playing External Disc Playing discs set in the optional accessory disc player connected to this unit Press the SRC button Select the display for the disc player you want Display examples Display Disc player CD CH CD changer MD CH MD changer Pause and play Press the Control knob Each time the knob is pressed it pauses and plays Disc 10 is displayed as 0 The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected Fast Forwarding and Reversing Fast Forwarding Hold down on gt of the Control knob Release your finger to play the disc at that point Reversing Hold down on lt lt of the Control knob Release your finger to play the disc at that point The sound is not output while the Audio file is being searched Fast Forwarding and Reversing cannot be done while AAC is being played KDC MP5028 MP528 only Fast Forwarding and Reversing cannot be done depending on AAC file format KDC X589 only Track File Search Searching for a song on the disc or in the Audio file folder Push the Control knob to ka a or gt gt 18 Engl
12. If you screw them in another hole it will contact and may cause damage to the mechanical parts inside the unit English 35 Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level Upper the frame and pull it forward as shown in the figure Accessory Removal tool 2 When the upper level is removed remove the lower two locations The frame can be removed from the bottom side in the same manner 36 English Removing the Unit 1 Refer to the section lt Removing the hard rubber frame gt page 36 and then remove the hard rubber frame 2 Remove the screw M4 x 8 on the back panel 3 Insert the two removal tools deeply into the slots on each side as shown Screw M4X8 commercially available Accessory Removal tool 4 Lower the removal tool toward the bottom and pull out the unit halfway while pressing towards the inside Be careful to avoid injury from the catch pins on the removal tool 5 Pull the unit all the way out with your hands being careful not to drop it Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems General The power does not turn ON vY The fuse has blown ts After checking for short circuits in
13. Select the Receive mode Push the Control knob to FM or AM Select the HDR MODE display 2 Enter Receive mode Press the Control knob for at least 1 second 3 Set the Receive mode Push the Control knob to FM or AM Each time the knob is pushed the Receive mode switches as shown below Receive mode _ Display Operation Auto mode AUTO Analog broadcasts and digital broadcasts will be switched automatically When both are being transmitted the digital broadcast will have priority Digital DIGITAL Digital broadcasts only Analog ANALOG Analog broadcasts only 4 Exit Receive mode Press the MENU button Even if the AUTO setting and analog broadcast will be received during the reception of a ball game mode non delayed broadcast program In SIRIUS tuner source SIRIUS ID ESN display Displaying the SIRIUS ID Electronic Serial Number Display MES Nm eR eT Serial amp SIRIUS ID ESN It is especially important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential future service changes Auxiliary Input Display Setting amp Station Disc Naming For selecting the display when switched to Auxiliary input source For the Station Disc Naming refer to the lt Station Disc Naming SNPS DNPS gt page 13 1 Select Auxiliary input source Press the SRC button Select the AUX AUX EXT display
14. an unauthorized change or modification is made NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment may cause harmful interference to radio communications if it is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help About CDs Handling CDs Don t touch the recording surface of the CD CD R and CD RW are easier to damage than a normal music CD Use a CD R or a CD RW after reading the caution items on the package etc Don t stick tape etc on the CD Also don t use a CD with tape stuck on it When using a new CD If the CD center hole or outside rim has burrs
15. fails to operate correctly Normal operation should be restored kxcelon systemes KENWOOD 40y Reset button We recommend the use of lt Security Code gt page 24 to prevent theft The characters which can be displayed by this unit are A Z 0 9 amp lt gt A The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on he display on the actual equipment and some of the illustrations on the display may represent something impossible in actual operation Cleaning the Unit If the faceplate of this unit is stained wipe it with a dry soft cloth such as a silicon cloth If the faceplate is stained badly wipe the stain off with a cloth moistened with neutral cleaner then wipe neutral detergent off A Applying spray cleaner directly to the unit may affect its mechanical parts Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters Cleaning the Faceplate Terminals If the terminals on the unit or faceplate get dirty wipe them with a dry soft cloth Before using this unit for the fir
16. for the first song or in the forward direction for the last song 38 English WV HD Radio tuner is connected to KCA S210A or other units t Connect the HD Radio tuner directly to the control unit The messages shown below display your systems condition EJECT NO DISC TOC ERR E 05 BLANK NO TRACK E 15 NO PANEL E77 o disc magazine has been loaded in he changer The disc magazine is not completely loaded Load the disc magazine properly o CD in the unit Insert the CD o disc has been loaded in the disc magazine Load a disc into the disc magazine o disc has been loaded in the disc magazine Load a disc into the disc magazine The CD is quite dirty The CD is upside down The CD is scratched a lot Clean the CD and load it correctly The CD is upside down Load the CD correctly jothing has been recorded on the MD o tracks are recorded on the MD though it has a title o edia was played that doesn t have data recorded that the unit can play Use media that has data recorded that the unit can play The faceplate of the slave unit being connected to this unit has been removed Replace it The unit is malfunctioning for some reason Press the reset button on the unit If the E 77 code does not disappear consult your nearest service center Something is wrong with the disc magazine Or the unit is malfunctioni
17. items that can be adjusted switch as shown below 4 Setup the Audio item Turn the VOL knob Adjustment Item _ Display Range Front High Pass Filter HPF Through 40 60 80 100 120 150 180 220 7 Hz Rear High Pass Filter HPR Through 40 60 7 80 100 120 150 180 220 7 Hz Low Pass Filter LPF 50 60 80 100 7 120 Through Hz Subwoofer Phase PHAS Normal 0 Reverse 180 Volume offset V OFF 8 0 Loudness LOUD OFF O Dual Zone System 2Z0N OFF O Volume offset Each source s volume can be set as a difference from the basic volume Loudness Compensating for low and high tones during low volume When it s ON LOUD indicator is ON You can control this item when lt Switching preout gt page 25 is set to SWPRE SW Function of the KDC MP5028 MP528 You can control this item when lt Subwoofer Output gt page 11 is set to SW ON You can control this item when 2ZON of lt Audio Setup gt page 11 is set to OFF KDC X589 MP5028 only The Dual Zone System can be used with the Auxiliary input sources shown below Internal auxiliary input KDC MP5028 MP528 only Option CA C1AX KDC X589 only Dual Zone System Main source and sub source Auxiliary input output Front channel and Rear channel separately The channel of sub source is set up by lt Dual Zone System Setting gt page 25 Main source i
18. system pauses Listening to the audio during a call Press the SRC button The CALL display disappears and the audio system comes back ON When the call ends Hang up the phone The CALL display disappears and the audio system comes back ON Tuner features leXcelon System E s 4 0 KENWOOD 24Bit DAC ROW REP gaer mao Y PAdo Sw v H Radio AUTO AME Band display BO m a a a a n c j SMENU 1 6 SRC Control knob ST indicator Tuning Selecting the station 1 Select tuner source Press the SRC button Select the TUNER display 2 Select the band Push the Control knob to FM or AM Each time the knob is pushed to FM it switches between the FM1 FM2 and FM3 bands 3 Tune up or down band Push the Control knob to ka a or gt gt During reception of stereo stations the ST indicator is ON Frequency display Preset station number Tuning Mode Choose the tuning mode Press the AUTO button Each time the button is pressed the Tuning mode switches as shown below Tuning mode Display Operation Auto seek AUTO 1 Automatic search for a station Preset station seek AUTO 2 Search in order of the stations in the Preset memory Manual MANUAL Normal manual tuning control Englis
19. 6 x 2 1 16 x 6 1 10 inch Weight 3 09 Ibs 1 4 kg
20. KENWOOD CD RECEIVER KDC X589 KDC MP5028 KDC MP528 INSTRUCTION MANUAL KENWOOD CORPORATION COMPACT Ay Designed for ISC ag wom NE Z DIGITAL AUDIO AAC PHATNOISE SIRIUS H Radio READY READY Take the time to read through this instruction manual Familiarity with installation and operation procedures will help you obtain the best performance from your new CD receiver For your records Record the serial number found on the back of the unit in the spaces designated on the warranty card and in the space provided below Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product Model KDC X589 KDC MP5028 KDC MP528 Serial number B64 2975 00 00 KW Contents Safety precautions 4 HD Radio control features 22 Tunin Notes 5 7 Menu system 23 Warning 6 enu System Security Code About CDs 7 Touch Sensor Tone About AAC MP3 and WMA 8 anual Clock Adjustment ou sd an DSI Disabled System Indicator General features 9 ety Illumination immer Power Switching preout Selecting the Source Built in Amp Setting Volume Dual Zone System Setting Attenuator B M S Bass Management System System Q B M S Frequency Offset Audio Control AMP Control Audio Setup CRSC Clean Reception System Circuit Subwoofer Output Receive mode Setting Speaker Setting SIRIUS ID ESN display Switching Display Auxilia
21. Track number at Audio file displays the last 3 digits when it exceeds 1000 songs KDC X589 only Album name cannot be displayed in WMA file KDC MP5028 MP328 only Song title Artist name and Album name cannot be displayed in AAC file KDC MP5028 MP528 only If the text for the Sirius tuner source including Channel name etc is selected when the channel which does not have text for the Sirius tuner source including Channel name etc is played band amp channel number is displayed Station Disc Naming SNPS DNPS Attaching a title to a Station or CD 1 Receive play the station disc you want to attach a title to A title can t be attached to MD or Audio file media 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Name set mode Push the Control knob to FM or AM Select the NAME SET display 4 Enter Name set mode Press the Control knob for at least 1 second 5 Move the cursor to the enter character position Push the Control knob to ka a or gt gt 6 Select the characters Push the Control knob to FM or AM Characters can be entered by using a remote with a numbers buttons Example If DANCE is entered Character Button Times pressed D B 1 A 2 1 N 6 2 G 2 3 E B 2 7 Repeat steps 5 through 6 and enter the name 8 Exit Menu mode Press the MENU button When operation stops for 10 se
22. atio MONO 70 dB Selectivity 400 kHz gt 80 dB Stereo separation 1 kHz 40 dB AM tuner section Frequency range 10 kHz space 530 kHz 1700 kHz Usable sensitivity S N 20dB 28 dBu 25 uV CD player section Laser diode GaAlAs Digital filter D A 8 Times Over Sampling D A Converter 1 Bit Spindle speed Audio file 1000 400 rpm CLV 2times Wow amp Flutter Below Measurable Limit Frequency response 1 dB 10 Hz 20 kHz Total harmonic distortion 1 kHz KDC X589 0 008 KDC MP5028 MP528 0 01 Signal to Noise ratio 1 kHz KDC X589 110 dB KDC MP5028 MP3528 105 dB Dynamic range 93 dB Channel separation 96 dB MP3 decode Compliant with MPEG 1 2 Audio Layer 3 WMA decode Compliant with Windows Media Audio AAC decode AAC LC m4a files 40 English Audio section Maximum output power 50W x4 Full Bandwidth Power at less than 1 THD 22Wx4 Tone action Bass 100 Hz 10 dB iddle 1 kHz 10 dB Treble 10 kHz 10 dB Preout level Load during disc play KDC X589 MP5028 4000 mV 10 kQ KDC MP528 2500 mV 10 kQ Preout impedance lt 6000 Auxiliary input KDC MP5028 MP528 Frequency response 1 dB 20 Hz 20 kHz Input Maximum Voltage 1200 mV Input Impedance gt 100 kQ General Operating voltage 11 16V allowable 144V Current consumption 10A Installation Size W x H x D 182 x 53 x 155 mm 7 3 1
23. conds the name at that time is registered and Name Set mode closes Memory numbers Tuner 30 stations Internal CD player 10 discs External CD changer player Varies according to the CD changer player Refer to the CD changer player manual The title of station CD can be changed by the same operation used to name it Faceplate Angle Adjustment Press the ANG button for at least 1 second Do not apply excessive force to the faceplate It can cause damage English 13 General features Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you helping to deter theft Removing the Faceplate Press the Release button The faceplate is unlocked allowing you to detach it The faceplate is a precision piece of equipment and can be damaged by shocks or jolts For that reason eep the faceplate in its special storage case while detached Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Reattaching the Faceplate 1 Align the shaft on the unit with the depression on the faceplate 2 Push the faceplate in until it clicks The faceplate is locked in place allowing you to use the unit 14 English TEL Mute The audio system automatically mutes when a call comes in When a call comes in CALL is displayed The audio
24. de In Disc source lt gt gt buttons Doing track file forward and backward buttons Doing disc folder forward and backward gt I button Each time the button is pressed the song pauses and plays 0 9 buttons When in lt Direct Track File Search gt page 18 and lt Direct Disc Search gt page 18 enter the track file disc number In SIRIUS tuner source FM button Select the preset band lt gt gt buttons Search up or down channel 0 9 buttons Press buttons 1 6 to recall preset channels DIRECT button Enters and cancels the lt Direct Access Tuning gt mode Refer to the instruction manual of SIRIUS Satellite radio tuner for lt Direct Access Tuning gt function In HD Radio source FM button Select the HD FM band Each time the FM button is pressed it switches between the HF1 HF2 and HF3 bands AM button Select the HD AM band lt gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations English 31 Accessories Installation Procedure Accessories SD om Installation Procedure 1 To prevent a short circuit remove the key from the ignition and disconnect the battery 2 Make the proper input and output wire connections for each unit 3 Connect the speaker wires of the wiring harness 4 Connec
25. der Select mode Press the F SEL button F SELECT is displayed During Select mode the folder information is displayed as shown below Folder name display Displays the current folder name It doesn t function when lt Disc Random Play gt page 19 is ON 2 Select the folder level Push the Control knob to FM or AM With the FM of the Control knob you move 1 level down and with the AM of the Control knob 1 level up Selecting a folder in the same level Push the Control knob to ka a or gt gt With the ka a of the Control knob you move to the previous folder and with the gt i of the Control knob to the next folder Returning to the top level Press the 3 button You can operate when lt Switching the Play mode gt page 20 is set to FOLDER while playing ACDrive disc KDC X589 only 3 Decide the folder to play Press the Control knob The Folder Select mode releases and the Audio file in the folder being displayed is played Canceling the Folder Select mode Press the F SEL button 20 English Function of the KDC X589 Function of ACDrive disc Switching the Play mode Arrange the playing orders of the songs by categories Press the S MODE button Each time the button is pressed the Play mode switches as follows The play mode indicator is ON Play mode Category which is to be arranged PLIST Play list order GENRE By genre ARTIST By artist
26. ections are made do not let the wire come out from the tab Wiring harness When using the optiona power amplifier connect to its V Accessory power control terminal Depending on what antenna you are using connect either to the control terminal of the motor antenna or to the power terminal for the booster amplifier of the film type antenna Connect to the terminal that is grounded when Power control wire Blue White Motor antenna control wire Blue either the telephone rings or during conversation amp To connect the KENWOOD navigation system consult your navigation manual i To EXT AMP CONT terminal of the amplifier having the external amp control function To car light control switch aoe ILLUMI 7 White Black White To front left speake To front right spea r Gray Black ra J TEL mute wire Brown External amplifier control wire Pink Black KDC X589 only Dimmer control wire Orange White REAR L FRONT R FRONT Gray To rear left speaker Green Black Green To rear right spea D Purple Black Purple Ignition key switch Car fuse box REARR Ignition wire Red Ure Car fuse box Main fuse Use Battery Battery wire Yellow Ground wire Black To car chassis English 33 Installa
27. ed Function of the KDC X589 Other than Standby mode B M S Frequency Offset Setting the central frequency boosted by B M S Display Setting BMSF NML Boost with the normal central frequency BMSF LOW Drop the normal central frequency 20 English 25 Menu system Function of the KDC X589 When LX AMP unit connecting AMP Control You can control the LX AMP connected to the unit 1 Select AMP Control mode Push the Control knob to FM or AM Select the AMS CTRL display 2 Enter AMP Control mode Press the Control knob for at least 1 second 3 Select the AMP Control item for adjustment Push the Contol knob to FM or AM For the details of the AMP Control item see the Instruction manual attached to the LX AMP 4 Adjust the AMP Control item Push the Control knob to ka a or gt gt 5 Exit AMP Control mode Press the MENU button You cannot use the LX AMP operation during standby mode In FM reception CRSC Clean Reception System Circuit Temporarily have reception switched from stereo to mono to reduce multi path noise when listening to the FM station Display Setting CRSC ON The CRSC is ON CRSC OFF The CRSC is OFF Strong electrical fields such as from power lines may cause unstable sound quality when CRSC is turned ON In such a situation turn it OFF 26 English In HD Radio mode Receive mode Setting Sets the receive mode 1
28. er the Security Code APPROVED is displayed The unit can be used In Standby mode Touch Sensor Tone Setting the operation check sound beep sound ON OFF Display Setting BEEP ON Beep is heard BEEP OFF Beep canceled In Standby mode Manual Clock Adjustment 1 Select Clock Adjustment mode Push the Control knob to FM or AM Select the CLK ADJ display 2 Enter Clock Adjust mode Press the Control knob for at least 1 second The clock display blinks 3 Adjust the hours Push the Control knob to FM or AM Adjust the minutes Push the Control knob to ka a or gt gt 4 Exit Clock adjustment mode Press the MENU button In Standby mode DSI Disabled System Indicator A red indicator will blink on the unit after the faceplate is removed warning potential thieves Display Setting DSI ON LED flashes DSI OFF LED OFF In Standby mode Selectable Illumination Selecting the button illumination color as green or red Display Setting KEY RED The illumination color is red KEY GRN The illumination color is green In Standby mode Dimmer Dimming this unit s display automatically when the vehicle light switch is turned ON Display Setting DIM ON The display dims DIM OFF The display doesn t dim Function of the KDC MP5028 KDC MP528 In Standby mode Switching preout Switching the preout between the rear and subwoofer In sub
29. fer to the catalog or consult your Kenwood dealer for connectable models of disc changers CD players ote that any KENWOOD disc changers CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit Unsupported connection may result in damage Setting the O N Switch to the N position for the applicable KENWOOD disc changers CD players The functions that can be used and the information hat can be displayed will differ depending on the models being connected AN You can damage both your unit and the CD changer if you connect them incorrectly LX bus connection The LX AMP and the sensor unit cannot be connected simultaneously You must connect any of them at a time Lens Fogging Right after you turn on the car heater in cold weather dew or condensation may form on the lens in the CD player of the unit Called lens fogging CDs may be impossible to play In such a situation remove the disc and wait for the condensation to evaporate If the unit still does not operate normally after a while consult your Kenwood dealer NOTE This Class B digital apparatus complies with Canadian ICES 003 Notes If you experience problems during installation consult your Kenwood dealer If the unit fails to operate properly press the Reset button The unit returns to factory settings when the Reset button is pressed Press the reset button if the disc auto changer
30. h 15 Tuner features Function of remote Direct Access Tuning Entering the frequency and tuning 1 Select the band Press the FM or AM button 2 Enter Direct Access Tuning mode Press the DIRECT button on the remote is displayed 3 Enter the frequency Press the number buttons on the remote Example Desired frequency Press button 92 1 MHz FM 0 9 2 1 810 kHz AM 0 8 1 0 Canceling Direct Access Tuning Press the DIRECT button on the remote Station Preset Memory Putting the station in the memory 1 Select the band Push the Control knob to FM or AM 2 Select the frequency to put in the memory Push the Control knob to ka a or gt gt 3 Put the frequency in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button 16 English Auto Memory Entry Putting stations with good reception in the memory automatically 1 Select the band for Auto Memory Entry Push the Control knob to FM or AM 2 Open Auto Memory Entry Press the AME button for at least 2 seconds When 6 stations that can be received are put in the memory Auto Memory Entry closes Preset Tuning Calling up the stations in the memory 1 Select the band Push the Control knob to FM or AM 2 Call up the station Press the desired
31. io file folder you are listening to and searching for the song you want to listen to 1 Start Scan Play Press the SCAN button TRAC SCN Y FILE SCN SCAN ON is displayed 2 Release it when the song you want to listen to is played Press the SCAN button Random Play Play all the songs on the disc or Audio file folder in random order Press the RDM button Each time the button is pressed Random Play turns ON and OFF When it s ON DISC RDM FOLD RDM RDM ON is displayed When the Control knob is pushed to gt the next random song starts Function of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order Press the M RDM button Each time the button is pressed the Magazine Random Play turns ON and OFF When it s ON MGZN RDM is displayed When the Control knob is pushed to gt the next random song starts Function of the KDC X589 Function of Audio file Disc Random Play Playing randomly from all of the Audio files recorded in the disc Press the RDM button for at least 1 second When it s ON DISC RDM is displayed Canceling the Disc Random Play Press the RDM button When the Control knob is pushed to gt the next random song starts English 19 CD Audio file External disc control features Function of Audio file Folder Select Quickly selecting the folder you want to listen to 1 Enter Fol
32. isc inserted t Press the 4 button and remove the disc Audio file source Cannot play an Audio file VW The media is scratched or dirty ts Clean the media referring to the CD cleaning of the section on lt About CDs gt page 7 The sound skips when an Audio file is being played VW The media is scratched or dirty t Clean the media referring to the CD cleaning of the section on lt About CDs gt page 7 Y The recording condition is bad ts Record the media again or use another media The Audio file track time isn t displayed correctly Vv ts There are times when it isn t displayed correctly according to the Audio file recording conditions HD Radio source No sound can be heard or the volume is low VW The preset broadcast station is not transmitting in the mode that was set with lt Receive mode Setting gt page 26 ts Please set lt Receive mode Setting gt to AUTO Y In digital AM broadcasting receive mode switches between stereo and monaural too often ts Receiving condition is bad or unstable Stereo is chosen when receiving condition is good and it switches to monaural when the condition becomes bad Direct Search can t be done Y Another function is ON ts Turn Random Play or other functions OFF Track Search can t be done Vv For the discs folders first or last song ts For each disc folder Track Search can t be done in the backward direction
33. ish Function of disc changer Audio file Disc Search Folder Search Selecting the disc set in the Disc changer or the folder recorded on the Audio file media Push the Control knob to FM or AM Function of remote Direct Track File Search Doing Track File Search by entering the track file number 1 Enter the track file number Press the number buttons on the remote Direct File Search can be selected up to 999 KDC X589 only 2 Do Track File Search Press the ka a or gt gt button Canceling Direct Track File Search Press the gt I button Function of disc changers with remote Direct Disc Search Doing Disc Search by entering the disc number 1 Enter the disc number Press the number buttons on the remote 2 Do Disc Search Press the or button Canceling Direct Disc Search Press the gt I button Input 0 to select disc 10 Track File Disc Folder Repeat Replaying the song disc in the Disc changer or Audio file folder you re listening to Press the REP button Each time the button is pressed the Repeat Play switches as shown below In CD amp External disc source Repeat play Display Track Repeat TRAC REP Disc Repeat In Disc Changer DISC REP OFF REP OFF In Audio file source Repeat play Display File Repeat FILE REP Folder Repeat FOLD REP OFF REP OFF Scan Play Playing the first part of each song on the disc or Aud
34. l wire is not connected ts Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt The desired frequency can t be entered with the Direct Access Tuning Y A station that can t be received is being entered se Enter a station that can be received Y You re trying to enter a frequency with a 0 01 MHz unit ts What can be designated in the FM band is to 0 1 MHz English 37 Troubleshooting Guide Disc source AUX EXT is displayed without achieving External disc control mode Y Unsupported disc changer is connected te Use the disc changer mentioned in the lt About CD players disc changers connected to this unit gt page 4 of the section on lt Safety precautions gt The specified disc does not play but another one plays instead Y The specified CD is quite dirty t Clean the CD VW The disc is loaded in a different slot from that specified te Eject the disc magazine and check the number for the specified disc Y The disc is severely scratched ts Try another disc instead Can t remove disc Y The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF ts The disc can only be removed within 10 minutes of the ACC switch being turned OFF If more than 10 minutes has elapsed turn the ACC switch ON again and press the Eject button The disc won t insert Y There s already another d
35. layed Playable AAC file m4a file encoded by AAC LC format Refer to http www kenwood mediamanager jp for the details Playable MP3 file PEG 1 2 Audio Layer 3 file Transfer bit rate 8 320 kbps Sampling frequency KDC X589 16 22 05 24 32 44 1 48 kHz KDC MP5028 MP3528 8 11 025 12 16 22 05 24 32 44 1 48 kHz Playable WMA file The file in accordance with Windows Media Audio Except for the file for Windows Media Player 9 or after which applies the new functions Transfer bit rate 48 192 kbps Sampling frequency 32 44 1 48 kHz Playable media CD ROM CD R CD RW Depending on the writing software it may not be possible to use quick formatted CD RW discs When recording to the media up to the maximum capacity at once the writing soft is set to Disc at once Playable disc format ISO 9660 Level 1 2 Joliet Romeo Long file name The maximum number of characters for display File Folder name KDC X589 128 characters KDC MP5028 MP3528 64 characters 8 English MP3 ID3 Tag WMA Contents property AAC song information KDC X589 only 30 characters File Folder name is the number of the characters including the extensions MP3 ID3 Tag can only display the tag of Ver1 X KDC MP5028 MP528 only AAC ID3 Tag cannot be displayed Limitation of structure for the file and the folder Maximum number of directory levels 8 Maximum number of folders 100
36. nel must be attached during the driving ACAUTION To prevent damage to the machine take the following precautions Make sure to ground the unit to a negative 12V DC power supply Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing To prevent deterioration do not touch the terminals of the unit or faceplate with your fingers Do not subject the faceplate to excessive shock as it is a piece of precision equipment When replacing a fuse only use a new one with the prescribed rating Using a fuse with the wrong rating may cause your unit to malfunction Do not apply excessive force to the open faceplate or place objects on it Doing so will cause damage or breakdown Do not use your own screws Use only the screws provided If you use the wrong screws you could damage the unit Do Not Load 3 in CDs in the CD slot If you try to load a 3 in CD with its adapter into the unit the adapter might separate from the CD and damage the unit 4 English About CD players disc changers connected to this unit KENWOOD disc changers CD players released in 1998 or later can be connected to this unit Re
37. ng for some reason gt Check the disc magazine And then press the reset button on the unit If the E 99 code does not disappear consult your nearest service center HOLD NO NAME LOAD READING IN Blink NA FILE COPY PRO The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60 C 140 F stopping all operation Cool down the unit by opening the windows or turning on the air conditioner As the temperature falls below 60 C 140 F the disc will start playing again Attempted to display DNPS during the CD play having no disc names preset Discs are being exchanged in the Disc changer The unit is reading the data on the disc The CD player section is not operating properly Reinsert the CD If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted please switch off the power and consult your nearest service center An Audio file is played with a format that this unit can t support Be A copy protected file is played gt English 39 Specifications Specifications subject to change without notice FM tuner section Frequency range 200 kHz space 87 9 MHz 107 9 MHz Usable sensitivity S N 30dB 9 30 Bf 0 8 uV 75 Q Quieting Sensitivity S N 50dB 15 2dBf 1 6 uV 75 Q Frequency response 3 dB 30 Hz 15 kHz Signal to Noise r
38. ol knob to AM 3 Tune up or down band Push the Control knob to ka a or gt gt Menu system O Ve excelon systeme s KENWOOD oer 40y PEER sins aes H Radio O 3 Cot at ee ea ey Menu System 4 Exit Menu mode Setting during operation beep sound etc Press the MENU button functions The Menu system basic operation method is When other items that are applicable to the basic explained here The reference for the Menu items operation method above are displayed afterwards and their setting content is after this operation their setting content chart is entered Normally the explanation uppermost setting in the chart is the original setting Also the explanation for items that aren t applicable 1 Enter Menu mode lt Manual Clock Adjustment gt etc are entered step Press the MENU button for at least 1 second by step MENU is displayed 2 Select the menu item Push the Control knob to FM or AM Example When you want to set the beep sound select the BEEP display 3 Set the menu item Push the Control knob to ka a or gt gt Example When BEEP is selected each time the knob is pushed it switches BEEP ON or BEEP OFF Select 1 of them as the setting You can continue by returning to step 2 and setting other items English 23 Menu system In Standby mode Security Code Because authorization by the Security
39. or adjustment By referring to the step 1 3 above select the desired item to be set in detail from the items marked with 2 Enter Detail adjustment mode of Audio Control Press the VOL knob for at least 1 second 3 Select the Detail Audio item for adjustment Press the VOL knob Each time the knob is pressed the items that can be adjusted switch as shown below 4 Adjust the Detail Audio item Turn the VOL knob Bass level Adjustment Item Display Range Bass Center Frequency BAS F 40 50 60 70 80 100 120 150 Hz Bass Q Factor BAS Q 1 00 1 25 1 50 2 00 Bass Extend B EX OFF ON Middle level Adjustment Item Display Range iddle Center Frequency MID F 0 5 1 0 1 5 2 0 kHz iddle Q Factor MID Q 1 0 2 0 Treble level Adjustment Item Display Range reble Center Frequency TRE 10 0 12 5 15 0 17 5 kHz 5 Exit the Detail Audio Control mode Press the VOL knob for at least 1 second When the Bass Extend is set to ON low frequency response is extended by 20 You can exit the Audio Control mode at anytime by pressing any button except for VOL ATT and ANG buttons Audio Setup Setting the Sound system such as Cross over Network 1 Select the source for adjustment Press the SRC button 2 Enter Audio Setup mode Press the VOL knob for at least 1 second 3 Select the Audio Setup item for adjustment Press the VOL knob Each time the knob is pressed the
40. p plays The category with marks or letters that cannot be read cannot be selected Text Title Scroll Scrolling the displayed CD text Audio file text or MD title Hold down on FM of the Control knob for at least 1 second English 21 HD Radio control features leXcelon System E s 4 0V SIRIUSH KENWOOD 24B DAC REP F SEL MADM t Ce Ce Cal ice Ce Ce SIRIUS Rep rset AUTO SAME emi ofePuS 5 HJ E Cal le cE ea CE Cage Ru Band display SRC Control knob ST indicator When you connect an HD Radio Tuner features of the unit are disabled and switched to HD Radio tuner features A portion of the setting methods including the Tuning Mode will change With the HD Radio tuner you can use the similar functions to lt Station Preset Memory gt lt Auto Memory Entry gt and lt Preset Tuning gt of Tuner features Refer to Tuner features for how to use the functions 22 English Frequency display Preset station number Tuning Selecting the station 1 Select HD Radio source Press the SRC button Select the HD RADIO display 2 Select the HD FM band Push the Control knob to FM Each time the knob is pushed to FMI it switches between the HF1 HF2 and HF3 bands Select the HD AM band Push the Contr
41. rol 1 Select the source for adjustment Press the SRC button 2 Enter Audio Control mode Press the VOL knob 3 Select the Basic Audio item for adjustment Press the VOL knob Each time the knob is pressed the items that can be adjusted switch as shown below 4 Adjust the Basic Audio item Turn the VOL knob Adjustment Item Display Range Rear Volume R VOL 0 35 Subwoofer level 34 SW L 15 15 Bass level 56 BAS L 8 8 Middle level MID L 8 8 Treble level 6 TREL 8 8 Balance BAL Left 15 Right 15 10 English Fader FAD Rear 15 Front 15 Exit Audio Control mode You can control this item when 2ZON of lt Audio Setup gt page 11 is set to ON You can control this item when lt Switching preout gt page 25 is set to SWPRE SW KDC MP5028 MP528 only You can control this item when lt Subwoofer Output gt page 11 is set to SW ON You can control this item when 2ZON of lt Audio Setup gt page 11 is set to OFF These items can be adjusted in detail by the following methods Function of the KDC X589 Source tone memory The set up value is put in the memory per source Detail Audio item is included 5 Exit Audio Control mode Press any button Press the button which is not VOL knob and ATT ANG button Adjust the detail of Audio Control 1 Select the Audio item f
42. ry Input Display Setting amp Station Disc Station Disc Naming SNPS DNPS aming Faceplate Angle Adjustment Text Scroll Theft Deterrent Faceplate Built in Auxiliary input Setting TEL Mute CD Read Setting Voice Index Tuner features 15 ACDrive firmware version display Tuning Unique ID display Tuning Mode Audio Preset Memory Direct Access Tuning Audio Preset Call Station Preset Memory Demonstration mode Setting Auto Memory Entr R Preset Fae 7 Basic Operations of remote 30 CD Audio file External disc control Accessories Installation Procedure 32 features 17 F Playing CD amp Audio file Connecting Wires to Terminals 33 Playing External Disc Fast Forwarding and Reversing Installation 34 Track File Search Disc Search Folder Search Removing the Unit 36 Die ctlrack hile Search Troubleshooting Guide 37 Direct Disc Search Track File Disc Folder Repeat Specifications 40 Scan Play Random Play agazine Random Play Disc Random Play Folder Select Switching the Play mode Letter Seek Text Title Scroll 2 English The AAC logo is trademark of Dolby Laboratories English 3 Safety precautions AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit Attach the panel while you are on the vehicle The panel lock arm will be appeared when the panel is removed Therefore the pa
43. s selected by SRC button The volume of Front channel is adjusted by VOL knob The volume of Rear channel is adjusted by lt Audio Control gt page 10 The Audio Control has no effect on sub source 5 Exit Audio Setup mode Press VOL knob for at least 1 second Subwoofer Output Turning the Subwoofer output ON or OFF Hold down on AM of the Control knob for at least 1 second Each time the button is pressed Subwoofer output switches ON and OFF When it s ON SW ON is displayed You can control this item when lt Switching preout gt page 25 is set to SWPRE SW KDC MP5028 MP528 only You can control this item when 2ZON of lt Audio Setup gt page 11 is set to OFF English 11 General features Speaker Setting In Audio file source Fine tuning so that the System Q value is optimal Information Display when setting the speaker type Song title amp Artist name TITLE Album name amp Artist name ALBUM 1 Enter Standby Folder name FOLDER Press the SRC button File name FILE Select the STANDBY display Track number amp Play time P TIME 2 Enter Speaker Setting mode Clock COCK Press the VOL knob In HD Radio source 3 Select the Speaker type RRIA RTE Turn the VOL knob Mormation Py s Station name ST NAME Each time the knob is turned the setting i Song title Artist name
44. splay Setting AUX OFF When selecting the source there s no Auxiliary Input AUX ON When selecting the source there s Auxiliary Input In Standby mode CD Read Setting When there is a problem on playing a CD with special format this setting play the CD by force Display Setting CD READ1 Play CD and Audio file CD READ2 Play CD by force Setting CD READ2 cannot play Audio file Some music CDs may not be played back even in the CD READ2 mode English 27 Menu system Function of the KDC X589 Function of ACDrive disc Voice Index Setting the announcement during the play of ACDrive disc Display Setting V ID ON Guide is announced V ID OFF Not be announced Function of the KDC X589 In CD mode ACDrive firmware version display Displaying the firmware version with the ACDrive function 1 Select the firmware version display mode Push the Control knob to FM or AM Select the ACD VER display 2 Display the ACDrive firmware version Push the Control knob to ka a or gt gt Function of the KDC X589 In CD mode Unique ID display Displaying the serial number for each product 1 Select the unique ID display mode Push the Control knob to FM or AM Select the ACD ID display 2 Display the unique ID Push the Control knob to ka a or gt gt 28 English Audio Preset Memory Registering the value setup by Sound Control The memor
45. st time This unit is initially set on the Demonstration mode When using this unit for the first time cancel the lt Demonstration mode Setting gt page 29 About SIRIUS Satellite radio tuner Refer to the instruction manual of SIRIUS Satellite radio tuner KTC SR901 SR902 SR903 optional accessory when connected for the operation method Refer to the sections of A models for operations System rs KENWOOD v English 5 Notes About DAB Tuner control Refer to A group on the Instruction manual of DAB Tuner KTC 9090DAB optional accessory for the control method of DAB Tuner function However the following control methods of the function for this unit may be differed from the Instruction manual therefore refer to the following supplemental instruction lt Auto Ensemble Memory Entry gt 1 Select the preset band for Auto Ensemble Memory Entry 2 Press the AME button for at least 2 seconds Open Auto Ensemble Memory Entry After storing in the memory finishes the number of the pre set buttons and the ensemble label are displayed lt Searching by programme type and language gt and lt Languages to be displayed gt in lt Programme Type PTY Function gt At the operation to press DISP button press AUTO button About Media Manager of PC application attached to KDC X589
46. t the remote on hot places such as above the dashboard 30 English Z l 2 ZONE OK Basic operations VOL buttons Adjusting the volume SRC button Each time the button is pressed the source switches For the source switching order refer to lt Selecting the Source gt page 9 ATT button Turning the volume down quickly When it is pressed again it returns to the previous level button Adjusting the Faceplate Angle Audio Control AUD button Select the Audio item for adjustment VOL buttons Adjust the Audio item Refer to lt Audio Control gt page 10 for the operation method such as the procedures of Audio control and others Only selecting and adjusting of the Basic Audio item can be done by the remote control Selecting and adjusting of the Detail Audio item cannot be done Dual Zone System 2 ZONE button Each time the button is pressed 2ZON of lt Audio Setup gt page 11 is turned ON and OFF A V buttons Adjusts the volume of the rear channel It activates while the Dual Zone System is ON In Tuner source FM AM buttons Select the band Each time the FM button is pressed it switches between the FM1 FM2 and FM3 bands lt 4 gt gt buttons Tune up or down band 0 9 buttons Press buttons 1 6 to recall preset stations DIRECT button Enters and cancels the lt Direct Access Tuning gt page 16 mo
47. t the wiring harness wires in the following order ground battery ignition 5 Connect the wiring harness connector to the unit 6 Install the unit in your car Reconnect the battery 8 Press the reset button N 32 English AWARNING If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box A If the power is not turned ON or it is ON but will be OFF immediately the speaker wire may have a short circuit or touched the chasis of the vehicle and the protection function may have been activated Therefore the speaker wire should be checked If your car s ignition does not have an ACC position connect the ignition wires to a power source that can be turned on and off with the ignition key If you connect the ignition wire to a power source with a constant voltage supply as with battery wires the battery may die the console has a lid make sure to install the unit so that the faceplate will not hit the lid when closing and opening the fuse blows first make sure the wires aren t touching to cause a short circuit then replace the old fuse with one with the same rating Insulate unconnected wires with vinyl tape or other similar material To prevent a short circuit do not remove the caps on the ends of the unconnected wires or
48. the terminals Connect the speaker wires correctly to the terminals to which they correspond The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car When only two speakers are being connected to the system connect the connectors either to both the front output terminals or to both the rear output terminals do not mix front and rear For example if you connect the connector of the left speaker to a front output terminal do not connect the connector to a rear output terminal After the unit is installed check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less Connecting Wires to Terminals KDC X589 KDC MP5028 MP528 Front left output White Front left output White Front right output Red Front right output Red Rear left output White Rear left output White Sub Woofer left output White B Rear right output Red Rear right output Red Sub Woofer right output Red E Sub Woofer left output White AUX left input White Sub Woofer right output Red AUX right input Red To KENWOOD disc changer External optional accessory amp To connect these leads refer to the relevant instruction manuals Fuse 10A FM AM antenna input i no conn
49. the wires replace the fuse with one with the same rating VW The speaker wire has a short circuit or touches the chassis of the vehicle and then the protection function is activated ts Wire or insulate the speaker cable properly and press the reset button There s a source you can t switch VW There s no media inserted ts Set the media you want to listen to If there s no media in this unit you can t switch to each source W The Disc changer isn t connected t Connect the Disc changer If the Disc changer isn t connected to it s input terminal You can t switch to an external disc source No sound can be heard or the volume is low Y The fader or balance settings are set all the way to one side ts Center the fader and balance settings V The input output wires or wiring harness are connected incorrectly te Reconnect the input output wires or the wiring harness correctly See the section on lt Connecting Wires to Terminals gt WY The values of Volume offset are low ts Turn up the Volume offset referring to the section on lt Audio Control gt page 10 VY The lt Built in Amp Setting gt page 25 is OFF t Turn it ON The sound quality is poor or distorted VY One of the speaker wires is being pinched by a screw in the car ts Check the speaker wiring V The speakers are not wired correctly ts Reconnect the speaker wires so that each output terminal is connected
50. tion non Japanese cars Metal mounting strap commercially available Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place S oO tapping screw commercially available Screw M4X8 commercially available Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip 34 English Japanese cars 1 Refer to the section lt Removing the hard rubber frame gt page 36 and then remove the hard rubber frame 2 Align the holes in the unit two locations on each side with the vehicle mounting bracket and secure the unit with the accessory screws T Toyota cars N Nissan cars 8mm Sse I Sf tm AD Ten MAX LO M5mm M5mm Accessory for Nissan car Accessory for Toyota car A During installation do not use any screws except for those provided The use of different screws might result in damage to the main unit Damage may occur if a screwdriver or similar tool is used with excessive force during the installations Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off screw in the provided screws in the holes shown below Bottom panel P Accessory Never insert the screw in any other screw hole than the one specified
51. to a different speaker The Touch Sensor Tone doesn t sound WY The preout jack is being used ts The Touch Sensor Tone can t be output from the preout jack The memory is erased when the ignition is turned OFF Y The ignition and battery wire are incorrectly connected t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt The TEL mute function does not work VY The TEL mute wire is not connected properly t Connect the wire correctly referring to the section on lt Connecting Wires to Terminals gt The TEL mute function turns ON even though the TEL mute wire is not connected VY The TEL mute wire is touching a metal part of the car ts Pull the TEL mute wire away from the metal part of the car Even if Loudness is turned ON high pitched tone isn t compensated for Y Tuner source is selected ts High pitched tone isn t compensated for when in Tuner source The Dimmer function doesn t work VY The Dimmer wire isn t connected correctly t Check the Dimmer wire connection VY The lt Dimmer gt page 25 is OFF ts Turn it ON The sound is not output from Subwoofer or it outputs the different sound VY When 2ZON of lt Audio Setup gt page 11 is set to ON Turn OFF 2ZON Tuner source Radio reception is poor WY The car antenna is not extended ts Pull the antenna out all the way Y The antenna contro
52. woofer it outputs without effect from the fader control Display Setting SWPRE R Rear preout SWPRE SW Subwoofer preout In Standby mode Built in Amp Setting Built in amplifier is controlled Turning OFF this control enhances the preout quality Display Setting AMP ON The built in amplifier activates AMP OFF The built in amplifier deactivates Other than Standby mode When the Dual Zone System is ON Dual Zone System Setting Setting the Front channel and Rear channel sound in the Dual Zone System Display Setting ZONE2 R Sub source Auxiliary input source is to be rear channel ZONE2 F Sub source Auxiliary input source is to be front channel Function of the KDC X589 Other than Standby mode B M S Bass Management System Adjust the bass boost level of the external amplifier using the main unit Display Setting BMS FLT Bass boost level is flat BMS 6 Bass boost level is low 6dB BMS 12 Bass boost level is mid 12dB BMS 18 Bass boost level is high 18dB Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit For amplifiers there are the model that can be set rom Flat to 18 dB and the model that can be set rom Flat to 12 dB When an amplifier that can only be set to 12 is connected to the unit BMS 18 won t work correctly even if it s select
53. y can t be erased by the Reset button 1 Setup Sound Control Refer to the following operations to setup the Sound Control lt Audio Control gt page 10 lt Audio Setup gt page 11 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Audio Preset mode Push the Control knob to FM or AM Select the A PRESET display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset Memory Push the Contol knob to FM or AM Select the MEMORY display 6 Put the Audio Preset in the memory Press the Control knob for at least 2 seconds The MEMORY display blinks 1 time 7 Exit Menu mode Press the MENU button Register 1 pair of Audio Preset Memory You can t register by the source When you press the Reset all the sources will be the setting value which is registered The following items can t be registered Volume Balance Fader Loudness Volume offset Dual Zone System Rear Volume Audio Preset Call Recalling the sound setup registered by lt Audio Preset Memory gt page 28 1 Select the source Press the SRC button 2 Enter Menu mode Press the MENU button for at least 1 second MENU is displayed 3 Select Audio Preset mode Push the Control knob to FM or AM Select the A PRESET display 4 Enter Audio Preset mode Press the Control knob for at least 1 second 5 Select the Audio Preset
Download Pdf Manuals
Related Search