Kenwood KCA-SR50 Satellite Radio User Manual
Contents
1. lt Switching Display gt page of the instruction manual of your control unit e What is displayed may partly depend on control units to be connected Channel Name Song litle Artist Name Composer name Category Name Band amp Channel Number Ifthe text including Channel name etc is selected when the channel which does not have text including Channel name etc is played band amp channel number is displayed Function of remote control Direct Access Tuning Entering the channel and tuning 1 Enter Direct Access Tuning mode Press the DIRECT button on the remote control 2 Enter the channel Press the number buttons 3 Do Channel Search Press the la a or gt button Canceling Direct Access Tuning Press the DIRECT button on the remote control If you make no button operation for 10 seconds the Direct Access Tuning mode is automatically canceled If you cannot receive any signal in the input channel due to a bad condition on radio wave or another problem Acquiring Signal ACQUIRING SIGNAL appears Accessories Installation Procedure Accessories Installation Procedure Nm fb To prevent a short circuit remove the key from the ignition and disconnect the battery Connect the SIRIUS interface box and the control unit using the provided SIRIUS connection wire Make the proper input and output wire connections for each unit Install the unit in you2. Press the desired 1 6 button English 5 Operations Channel Scan Every receivable channel is checked for 10 seconds 1 Start Channel Scan Press the AUTO button for at least 2 seconds The channel scan will start 2 Release it when the channel you want to listen to is received Press the AUTO button for at least 2 seconds Switching Seek Mode Sets the seeking mode Press the AUTO button Each time the button is pressed the Seek mode switches as shown below Display Torr T r Op ae Channel CHANNEL or anual seeking contro Preset PRESET Search in order of the channels in the Preset memory This function cannot be used in the category and channel search mode it Category and Channel Search Select the category and channel you wish to listen to 1 Enter category and channel search mode Press the gt I button 2 Select the category Push the Control knob towards up or down EJ Press the FM or AM button 3 Select the channel Push the Control knob towards right or left E Press the e a or gt gt button Canceling category and channel search mode Press the PII button e You cannot operate this unit until all the Category information is acquired 6 English Switching Display When you are listening to the Sirius satellite radio you can switch over the display information as follows For operations see the
3. IRIUS TO SUBSCRIBE CALL 888 539 SIRI appears It may take a little time to start receiving after you selected the SIRIUS source If the signal receiving fails Acquiring Signal ACQUIRING SIGNAL appears Selecting the Preset Band Push the Control knob toward up Each time you push the knob toward up it switches between the SR1 SR2 SR3 and SR4 EJ Press the FM button Each time the button is pressed the preset band switches between the SR1 SR2 SR3 and SR4 Tuning Selecting the channel Push the Control knob towards right or left EJ Press the kaa or gt gt button Channel Preset Memory Putting the channel in the memory 1 Select the preset band Push the Control knob toward up E3 Press the FM button 2 Select the channel to put in the memory Push the Control knob towards right or left EJ Press the kea or gt button 3 Put the channel in the memory Press the desired 1 6 button for at least 2 seconds The preset number display blinks 1 time On each band 1 station can be put in the memory on each 1 6 button Only the channel number is stored Category information is not stored This function can be used only when the Channel CHANNEL has been selected in lt Switching Seek Mode gt page 6 Preset Tuning Calling up the channels in the memory 1 Select the preset band Push the Control knob toward up EJ Press the FM button 2 Call up the channel
4. KENWOOD KCA SR50 SIRIUS INTERFACE BOX FOR CONNECTING KENWOOD HEAD UNITS TO SIRIUS RECEIVERS INSTRUCTION MANUAL BOITIER D INTERFACE SIRIUS POUR BRANCHEMENT D UNITES PRINCIPALES KENWOOD AU RECEPTEURS SIRIUS MODE D EMPLOI CAJA DE INTERFACE SIRIUS PARA CONECTAR UNIDADES KENWOOD A RECEPTORES SIRIUS MANUAL DE INSTRUCCIONES Kenwood Corporation SIRIUS cCorsvect 2007 Sirius Satellite Radio Inc SIRIUS the SIRIUS dog logo and related marks are trademarks of Sirius Satellite Radio Inc Take the time to read through this instruction manual Familiarity with installation and operation procedures will help you obtain the best performance from your new SIRIUS interface box For your records Record the product number found on the back of the unit in the space provided below Refer to the model and product numbers whenever you call upon your Kenwood dealer for information or service on the product Model KCA SR50 Product number B64 3921 00 01 K Contents m a Safety precautions Notes 3 Notes 4 Operations 5 How to read SIRIUS ID ESN display Select SIRIUS Satellite Radio Mode Selecting the Preset Band Tuning Channel Preset Memory Preset Tuning Channel Scan Switching Seek Mode Category and Channel Search Switching Display Direct Access Tuning Accessories Installation Procedure 7 Connecting Wires to Terminals 8 Installation 9 Troubleshooting Guide 10 Specifications 11 2 English
5. P535U KOC MP435U KDC MP3035 KDC MP335 KDC MP2035 KDC MP235 DPX502 DPX302 KVT 819DVD KVT 719DVD DDX8019 DDX7019 DNX7 100 DNX710EX KOS V1000 KOS V500 2006 models KDC X990 KDC X890 KDC X790 KDC MP832U KDC MP7 32 KDC X590 KDC MP632U KDC MP532U KDC MP5032 KDC MP4032 KDC MP2032 KDC MP332 KDC MP232 KDC 232MR DPX701 DPX501 DPX301 KDV 412 KVT 617DVD DDX6019 KOS A200 2005 models XXV 01D KDC X889 KDC X789 KDC MP928 KDC MP828 KDC MP7028 KDC MP728 KDC MP628 KDC X589 KDC MP5028 KDC MP528 KDC MP4028 KDC MP428 KDC MP2028 KDC MP228 KDC 3028 KDC 328 KDC 228 Ez500 XXV 05 KVT 817 DVD KVT 717DVD KVT M707 DDX8017 DDX7 017 For the models marked with the operation method is different from that discussed in this manual Refer to the Instruction Manual that comes with each control unit For the connectable models released since 2008 contact the dealer 4 English NOTE When initially activating your subscription if you have changed your subscription or if SIRIUS itself has updated streaming broadcast service automatic reselection of reception operates by following the current channel setting At this time audio reception may be momentarily interrupted However this interruption is not caused by radio interference or reception interference FCC WARNING This equipment may generate or use radio frequency energy Changes or modifications to thi
6. Safety precautions Notes AWARNING To prevent injury or fire take the following precautions To prevent a short circuit never put or leave any metallic objects such as coins or metal tools inside the unit e Mounting and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals ACAUTION To prevent damage to the machine take the following precautions Do not open the top or bottom covers of the unit e Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing Use only the screws provided or specified for installation If you use wrong screws you could damage the unit e When drilling a hole in the car to fix the brackets make sure not to damage the fuel tank brake tube wiring harnesses etc on the other side NOTE If you experience problems during installation consult your Kenwood dealer If the unit does not seem to be working right try pressing the reset button on the control unit first If that does not solve the problem consult your Kenwood dealer When the reset button is pressed the SIRIUS satellite radio becomes ready to receive after approximately 15 seconds English 3 Notes Connectable Models 2007 models KDC X991 KDC X891 KDC X791 KDC MP735U KDC MP635 KDC X591 KDC X491 KDC M
7. et button of Control unit ESN ERROR ESN ERR ESN Electronic Serial Number is not registered in this unit Consult your nearest service center CHECK SIRIUS CHK SSR The SIRIUS tuner is disconnected or a unit other than the SIRIUS tuner is connected Check the connection to the SIRIUS tuner Specifications a anne none Se Specifications subject to change without notice General Operating voltage 11 16V allowable 144V Current consumption 420 MA Installation Size W x H x D 127 x 35 x 52 MM 5 x 1 3 8 x 2 1 16 inch Weight 0 17 kg 0 37 lbs English 11 KENWOOD
8. is for the first time it may be difficult to receive signals in the beginning In such a case leave the SIRIUS source ON for 3 minutes and turn it OFF and ON What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring Before calling service first check the following table for possible problems The SIRIUS mode cannot be selected Y The SIRIUS connection wire is not connected ce Use the SIRIUS connection wire to connect the oaaao control unit and the SIRIUS satellite radio tuner Yy The changer switching unit KCA S220A is not connected properly tb Connect the KCA SR50 to the terminal labelled TO CHANGER 2 See the section on lt Connecting Wires to Terminals gt Nothing happens when the buttons are pressed Y The computer chip in the unit is not functioning normally Press the reset button on the Control unit No broadcast can be received Y No subscription is established n Subscribe to SIRIUS 10 English The following messages are displayed when certain problems are occurring in your system Take the recommended actions ANTENNA ERROR ANT ERR ANT ERROR Antenna is not connected correctly c Make sure the antenna is connected correctly and then turn OFF ON of the SIRIUS source or Control unit TUNER ERROR TUNE ERR Broadcast cannot be received due to an error in this unit m gt Turn OFF ON of the SIRIUS source or Control unit or press the res
9. other than the SIRIUS Universal SIRIUS tuner A failure could result Tuner or Portable Tuner If you want to connect KCA S220A Control unit KCA SR50 el KCA S220A TO TO CHANGER 1 CHANGER 2 Connect the KCA SR50 to the terminal labelled TO CHANGER 2 A Please keep the total extension of the control cable from the control unit to the disc changer to 13 m or less Control cable lengths in excess of 13 m will cease to function properly 8 English Installation uN Installation using the velcro tapes install the unit in a well ventilated location and do not place objects on top of it When installing to the car the unit should be securely fastened at a location that will not interfere with driving When making a hole in the chassis check that the gas tank break pipe wire harness or other part is not located on the other side and be careful not to cause scratches Installation using the self tapping screws Accessory 04 x 12 mm Please do not install the unit near the dashboard the rear tray or other important components Doing so could lead to injury or accident should the unit come off due toa shock and strike a person or an important component Tapping screws should be used for mounting Attachment with velcro strips although easy can come off with a shock Carpet Board etc thickness 15 mm or more English 9 Troubleshooting Guide If you use th
10. r car Reconnect the battery Press the reset button A Do not connect the SIRIUS connection wire while the control unit is turned ON Be sure to press the reset button on the control unit after installation If your car is not prepared for this special connection system consult your Kenwood dealer Make sure that all wire connections are securely made by inserting jacks until they lock completely Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity To prevent short circuits also do not remove the caps on the ends of the unconnected wires or the terminals Insulate unconnected wires with vinyl tape or other similar material Take care so that the antenna wire and other connection wires are not caught by mobile parts Otherwise wire disconnecticn or other trouble may result Do not apply too much force on the antenna wire other connection wires and connectors by bending a wire etc Otherwise wire disconnection or other trouble may result After the unit is installed check whether the brake lamps indicators wipers etc on the car are working properly English 7 Connecting Wires to Terminals To Kenwood disc changer SIRIUS control input When using with the KCA BT100 or KTC HR1OOTR connect to it Control unit KCA SR50 SIRIUS connection wire Accessory KCA SR50 Do not connect any unit
11. s equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made NOTE This Class B digital apparatus complies with Canadian ICES 003 Operations How to read The operation method differs depending on the model of the control unit For the model with a Control knob perform the operation steps marked with J For other models perform the operation steps marked with E SIRIUS ID ESN display You must have the SIRIUS ID number ESN for licensing with SIRIUS Corp Check the SIRIUS ID ESN of this unit as follows 1 Select the SIRIUS Satellite Radio Mode Press the SRC button Select the SIRIUS SAT display 2 Check the SIRIUS ID ESN of this unit See the lt Menu System gt page of the instruction manual of your control unit and select the ESN menu item The SIRIUS ID ESN will be displayed Serial amp SIRIUS ID ESN It is especially important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential future service cnanges Select SIRIUS Satellite Radio Mode Listening to the SIRIUS satellite radio Press the SRC button Select the SIRIUS SAT display You need to subscribe to SIRIUS to receive the service by SIRIUS Satellite Radio Consult SIRIUS if CALL 888 539 S
Download Pdf Manuals
Related Search