Kenwood DT-7000S Car Stereo System User Manual
Contents
1. 5 When the display shows the correct hour and minute press the ENTER button to turn the alarm on 6 Press the MEMO button to save your settings The Step 2 Set Stream screen will appear right Step 2 Set Stream Screen 7 Use the CH PRESET jog dial unit or press the CH buttons remote to move through the streams until the one you want is highlighted The stream will play 8 Press the ENTER button to save your setting The Alarm Setup screen will reappear Press the SETUP button to exit the Setup Mode Using the alarm At the specified time see Setting The Alarm the DT 7000S will automatically turn itself on to the selected stream e The selected stream will play and the time display will flash positive and negative Note To hear the DT 7000S make sure that the audio system it is connected to is turned on To enter the Snooze mode press any button once e The Snooze cycle is 10 minutes long e You can repeat the Snooze cycle as many times as you want To shut the alarm off press any button twice This shuts the DT 7000S completely off To continue listening to SIRIUS after you ve shut the alarm off press the POWER button Auto Shutoff You can set DT 70005 to automatically shut off if it is accidentally left on if a button isn t pressed for 15 30 or 60 minutes 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Auto Shutoff Setup sc2. Lightning Unplug the DT 7000S from the wall outlet and disconnect the antenna when it will be unused for a long period of time Damage requiring service The DT 7000S should be serviced by qualified service personnel when e The power cord or plug has been damaged e Objects have fallen or liquid has been spilled into the tuner e The tuner has been exposed to rain or water e The tuner does not appear to operate normally by following the instructions in this manual e The tuner has been dropped or its chassis damaged e The tuner exhibits a marked change in performance Outdoor antenna grounding If an outside antenna is con nected to the DT 7000S be sure the antenna system is grounded so as to provide some protection against volt age surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides informa tion with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to ground ing electrodes and requirements for the grounding elec trode See the illustration below GROUND ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 POWER SERVICE GROUNDING GROUND CLAMPS ELECTRODE SYSTEM NEC ART 250 PART H Power lines An outside antenna system should not be located in the vic
3. Preset List Screen Bank Name Input Screen l Bank Hane nr Bank Select Screen Bank Name input Bank Naming Screen nil letters KENWOOD button on the unit Bank Name Input e If you make a mistake use the CH buttons to move the cursor to the left PA RTY of the letter you want to delete and press the DELETE button 6 Repeat Step 5 to complete the name Completed name gt ai OS non Bank e lite Press the utton to save your A T ei choice second right PART Ca DANA Press the SETUP button twice to exit DANK A BANK a the Setup Mode Saved name Saving recalling music information Saving music information You can store the name of the current ly playing song and artist and compos er if the data is available into memory for recall later Press the MEMO button to save the data The Data Saved screen will Data Saved Screen display the following message for a few seconds above e You can save data for up to 24 songs Once all 24 places have been filled any new artist song data you save will replace the oldest data e If the song has already been stored in memory the display will read Already Stored Recalling music information 1 Hold the MEMO button for more than 1 second The Song Memory List screen will appear right 2 Use the CH PRESET jog dial or CH buttons to scroll through the list Song Memory List Screen Press the MEMO button to exit Activati
4. materials in case you need to ship your DT 7000S in the future 2 SCIEGUANE MUSIC seu Setting and using stream presets Naming preset banks 4 Saving and recalling music information Display CDN an eine Setup MODE caca Troubleshooting Pillen Specification Savater Safety precautions WARNING TO PREVENT FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS TUNER TO RAIN OR MOISTURE A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL THE LIGHTNING FLASH WITH ARROW HEAD SYMBOL WITHIN AN EQUILATER AL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNIN SULATED DANGEROUS VOLTAGE WITHIN THE PRODUCT S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNI TUDE TO CONSTITUTE A RISK OF ELEC TRIC SHOCK TO PERSONS THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE SERVICING INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS PRODUCT Warning e If the tuner emits smoke or strange smells turn the power off immediately unplug the power cord and consult your Kenwood dealer e Do not drop the tuner or subject it to strong shocks e If the LCD display becomes damaged or broken do not touch the liquid crystal fluid The fluid may be dangerous
5. e Use the CH PRESET jog dial front panel or CH Buttons remote to scroll through the list When the desired stream is highlighted on the display press the ENTER button to select it Naming preset banks You can personalize the four banks of stream presets by assigning a name up to 6 characters to each one For example you can set up different preset banks for family members Dad Billy etc or assign a particular type of music to each one Mellow Party etc Note Although you can use the corresponding buttons on the unit to name the banks it is simpler to use the remote 1 Press the SETUP button to enter the Setup Mode 2 Press the CAT buttons until the Bank Name Input screen appears top right 3 Press the CH button once The Bank Select screen will appear second right Use the 4 arrow buttons to highlight the bank you want to name 4 Press the ENTER button The Bank Naming screen will appear above Press the DELETE button multiple times to delete all the letters of the existing name Note There is no DELETE button on the unit Bank Name Input 5 Press a number button multiple times to select the letters you want right When the letter you want is highlighted press the ENTER button The letter will appear in the name To add spaces press the SPACE button Note There is no SPACE DT 7000S Instruction Manual PIG The Vault Pl 20 The i Pek Pia inet
6. touch the 1 button then immediately hold the 2 button for at least 2 seconds e The selected preset number will flash and then remain lit on the display to show that it has been memorized e If the preset button already has a stream stored in it it will be replaced with the new stream Tuning stream presets The 20 presets in the active bank can be selected by pressing the number buttons 1 Press the BANK button to cycle through the four banks of preset stations The display will show the current preset bank and active preset number in the lower left corner 2 When the desired preset bank is displayed use the number buttons to select the desired preset stream Searching for a stream preset Preset List Screen There are two ways you can search for a stream preset For both press the SEEK button to enter the Preset Tune mode The Normal Operation Screen will change so that the preset bank and preset number will be highlighted right Option 1 Use the CH PRESET jog dial front panel or CH Buttons remote to move through Highlighted The Vault Preset Bank amp Number Preset Tune Screen DT 7000S Instruction Manual the presets Each time you change a preset its number will appear on the display and the stream will play Option 2 Press the ENTER button The Preset List Screen will appear on the display listing all of the stream presets that have been programmed in all 4 banks right
7. using CS and MEMO key Confirm Number Screen e If you entered the code incorrect ly Code Error will be displayed and the Enter New Lock Code screen reappears Repeat Steps 5 8 Startup Mode You can select which screen is displayed when you turn the DT 7000S s power on 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Startup Mode screen appears right 2 Use the CH PRESET jog dial unit or the CH buttons remote to highlight the screen you want for Startup Normal Operation Channel List Stream List or Category List see pages 7 8 Push the SETUP button to exit Startup Mode Screen Output Level You can adjust the DT 7000S s output level so it matches other sources in your audio system 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Output Level screen appears right 2 Use the CH PRESET jog dial unit or the CH buttons remote to select the desired output level e High is OdB Medium is 3dB and Low is 60B Push the SETUP button to exit utet Level High Medium MOR Output Level Screen Antenna Signal This screen shows the quality of the SIRIUS satellite signal that s being received to help you find the best location for the antenna 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote unt
8. 2003 KENWOOD USA Corporation All Rights Reserved 0020 0903 DT7000 INST
9. Polarization The DT 7000S is fitted with a polarized AC plug having one blade wider than the other DT 7000S Instruction Manual This plug will fit into the outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If it should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Ventilation Do not block the ventilation openings on the back of the DT 000S Place the tuner at least 4 inches away from the wall When placing the DT 7000S in a rack or built in installation take care to provide proper ventilation Water 8 moisture Do not use the DT 7000S near water do not expose it to dripping or splashing liquids do not place objects filled with liquids such as vases on the tuner Temperature The DT 7000S may not work properly if used at extremely low or freezing temperatures The ideal ambient temperature is above 41 F 5 C Heat Do not install the DT 000S near heat sources such as radiators heat registers stoves or other appli ances that produce heat Electric shock Do not place objects or spill liquids into the ventilation openings If a metal object comes into con tact with the inside of the tuner a dangerous electric shock may result Never remove the enclosure If internal parts are touched accidentally a serious electric shock could occur
10. fit on the highlight bar will scroll 2 Use the CH PRESET jog dial front panel or CH Buttons remote to move through the list of songs Stream Number Song List Screen 3 When the song you want to hear is highlighted press the ENTER button to listen to it e After you make your selection the display will revert to the Normal Operation screen Note In the Stream List Artist List and Song List modes if you don t want to make a selection press the SETUP button to exit the mode and return to the Normal Operation screen for the active stream Setting using stream presets Setting stream presets You can store up to 80 of your favorite streams as presets for quick access Presets are stored in 4 nameable banks each containing 20 stream presets 1 Press the BANK button to activate the preset bank you want The 01 6 selected bank is shown in the lower 12 00P pea The Vault ROCK left corner of the Normal Operation Screen right Jugalband Preset Bank Name 2 Select the stream you want to preset see Basic Operation and Selecting entertainment pages 7 8 Preset Number Preset Bank Normal Operation Screen showing Preset Bank and Preset Number Readout 3 Hold the number button you want to store the stream in for at least 2 seconds e To store presets 10 20 touch the 1 button then immediately hold the second number button for at least 2 seconds For example to set preset 12
11. receiving the SIRIUS signal preview stream 184 you will hear audio If you do not hear audio re orient the antenna until you do See Antenna Signal on page 12 to use the ANTENNA SIGNAL screen e Stream 184 is the SIRIUS preview stream You will not be able to tune to any other streams until you activate your SIRIUS subscription 5 Press the SETUP button to enter the Setup Mode 6 Your unit s unique 12 digit SIRIUS ID Number will be displayed below Write the number down and have your credit card handy 7 Contact SIRIUS on the Internet at www siriusradio com Click on the Activate Your Subscription link Sirius ID 000042117400 e You can also call SIRIUS toll free at 1 888 539 SIRIUS 7474 The operator will instruct you 8 Once your subscription has been activated the display will read Subscription Updated for 3 seconds then will revert to the Normal Operation screen SIRIUS ID Screen DT 7000S Instruction Manual Basic operation After you have acti Stream Number vated your SIRIUS Stream Name Stream Category subscription the Normal Operation screen will appear right Pr Bank Use the CH PRE reset Bank SET jog dial front panel or CH Buttons remote to select streams Preset Bank Current and Number Time Artist Song Title scrolling e The selected stream Normal Operation Screen will automatically play The name and artist of the currently playing song w
12. to your health or even fatal If the liquid crystal fluid contacts your body or cloth ing immediately wash it off with soap and water Caution Take the following precautions to keep the DT 7000S in proper working order e Do not install the tuner where it will be exposed to high levels of humidity moisture or dust When replacing a fuse use only a new one with the proper rating Using a fuse with the wrong rating may cause the tuner to malfunction Resetting the microprocessor If the DT 7000S doesn t seem to be working properly e Turn the tuner s power off wait 5 10 seconds then turn the power on again e If the tuner still mis operates unplug the power cord from the wall outlet wait 5 10 seconds replace plug the cord back into the wall outlet and turn the power back on lf the problem persists consult your Kenwood dealer DT 7000S Instruction Manual KENWOOD Safety precautions continued FCC Warning This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in this instruction manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide r
13. 0 SEEK MODE Button Switches the action of the CH PRESET Jog Dial and CH Buttons between the Stream and Preset seek modes CH PRESET Jog Dial unit CH Buttons remote Accesses Streams and Presets oa KENWOOD 12 00P BANK 2 DELETE Button remote only Deletes characters from Preset Bank names see page 9 SPACE Button remote only Puts spaces in Preset Bank names see page 9 016 The Vault i SIRIUS q B2 B3 a Q Jugalbandi Cam ger D 2 VOR 4 B21 Va No y a a Remote Control DIRECT SETUP BANK ENTER Receiver Button Button Button Button STANDBY Indicator unit only Illuminates when the DT 000S is in the Standby mode POWER OFF POWER ON Button Button Remote Control Receiver Number Receives signals from the included IR remote control Buttons DIRECT Button Accesses streams directly by number Press DIRECT then use the number buttons to enter the stream number DISPLAY DIRECT SETUP Button Button Button Enters and exits the Setup mode see page 10 cn B BANK Button als Cycles through the four banks of stream presets see page 8 CH Buttons ENTER Button BANK Press to select items highlighted on the display hold down to Button SER jump to the previously received stream MEMORY Button utton CH SCAN Button remote only Press to automatically scan through all of the available streams BETUP pe DE DIMMER Button remote only DIMMER CH SCAN Cycles the display between 3 br
14. KENWOOD SIRIUS DT 000S y SIRIUS Satellite Home Tuner E LE Instruction Manual KENWOOD Table of contents Be A e oo II En e NE e BOX CONS ERANO i i Rune a i Safety precautions siais iai ii i k a tases d ou Connecting the DT 7000S to your audio system seen Finding a location for the optional Kenwood CX SRH30 antenna aaa EEE UM Installing batteries in the remote control sentiste ls A e E RE a na Activating your SIRIUS subscription secar a ii oe EEE er EA CONGRATULATIONS Your DT 7000S SIRIUS home tuner lets you enjoy SIRIUS Satellite s digital entertainment streams through your home entertainment system Use this manual to familiarize yourself with all of the DT 7000S s features and capabilities For the latest information about this and other Kenwood products visit the Kenwood USA Corporation Web site at www kenwoodusa com For the latest information about SIRIUS Satellite visit the SIRIUS Web site at www siriusradio com SIRIUS Box contents Unpack your DT 7000S carefully and make sure that everything listed here is present N 2 x AAA batteries RC TO710 Remote RS 232C control Optical digital cable cable cable Stereo audio If anything is missing or damaged or if your DT 7000S fails to operate notify your dealer immediately If your DT 000S was shipped to you directly notify your shipper immediately Kenwood recommends that you retain the original carton and packing
15. To cancel the Sleep Timer turn the DT 7000S s power off then turn it back on again Note You must re set the Sleep Timer each time you want to use it Channel Skip Lock This allows you to select streams that you want to skip when scanning up and down the Channel List and Category List screens or simply when you re pressing the cursor up amp down buttons 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Channel Skip Lock screen appears right 2 Use the CH PRESET jog dial unit or the CH buttons remote to highlight the stream you want The highlighted stream will automatically play 3 Press the ENTER button to change the highlighted stream s status from available to skip e To exit the Channel Skip function turn the CATEGORY jog dial unit or press the CAT buttons remote The screen will display the next Setup Menu item Channel Skip Screen You can further lock a stream by placing it in the Channel Lock mode Locked streams will be unavailable during all tuning modes and cannot be directly accessed via the remote control To lock a stream in Step 3 above instead of momentarily pressing the ENTER button hold the button for more than 1 second A and a padlock will be displayed next to the stream number KENWOOD Lock Code Setup If you have locked any streams in the Channel Lock mode you will need to enter a 4 di
16. eason able protection against harmful interference in a residential installation This equipment may cause harmful interference to radio communications if it is not installed and used in accordance with these instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interfer ence to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one of more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected e Consult the dealer or an experienced radio TV techni cian for help Cleaning the DT 7000S If the tuner becomes dirty turn its power off and wipe it clean with a soft dry cloth Do not use hard cloths or paint thinner alcohol or other volatile solvents to clean the tuner These may cause damage or remove indicator characters Important Safeguards Power Source Connect the DT 7000S only to a 120V 60Hz AC power supply If you are not sure of the type of power supply to your home consult your local power company Power cord protection Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against it CAUTION
17. elow Stream Name ESEN Radio Netuork Stream 2 Use the CH PRESET jog dial front Number panel or CH Buttons remote to move through the list of streams 3 When the stream you want is highlighted press the ENTER button to play the stream The display will automatically return to the Normal Operation screen Sports Byline USA Speed Channel Radio Stream List Screen Selecting entertainment by artist Artist List Mode 1 While the Normal Operation screen is active press the ENTER button once then the DISPLAY button once The Artist List screen will appear showing all currently playing artists regardless of category below elf composer information is Stream available for a stream it will be Number displayed along with the artist information 2 Use the CH PRESET jog dial front panel or CH buttons remote to move through the list of artists Artist Name Ernie Gledsoe Jusalbardi The Lheaters Sek eu nul Artist List Screen 3 When the artist you want to hear is highlighted press the ENTER button to listen to them e After you make your selection the display will revert to the Normal Operation screen Selecting entertainment by song Song List Mode 1 While the Normal Operation screen is active press the ENTER button once then the DISPLAY button twice The Song List screen will appear showing all currently playing songs regardless of category right e Song titles too long to
18. git lock code to unlock them The factory default lock code is 1 1 1 1 You can change the Lock Code to your own preference 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Lock Code Setup screen appears top right 2 Turn the CH PRESET jog dial unit or press the CH buttons remote The Lock Code screen appears second right Lock Code ck Code and re 3 Using the number buttons enter the factory default code 1 1 1 1 The screen s second line will change from E ret MEME Key Code Screen e If you enter an incorrect number use the left CAT button or jog dial to delete the incorrect number then re enter the correct one 4 Press the MEMO button The Enter New Lock Code screen appears right e If you entered the code incorrect ly Code Error will be displayed and the Enter New Lock Code screen reappears Repeat Steps 3 4 5 Using the number buttons enter your new 4 digit code The screen s second line will change from _ _ _ _ to 7 Enter New Lock ade using 0 9 and 55 MEMO Key Enter New Lock Code Screen Lode 6 Press the MEMO button The Confirm Number screen appears below 7 Re enter your new 4 digit code The screen s second line will change from u ne se to tl K 8 Press the MEMO button The display will change to New Code Confirmed Confirm number
19. ightness levels see page 10 Button Button DELETE SPACE Button Button KENWOOD RC T0710 DT 7000S Instruction Manual KENWOOD Installing batteries in the remote 1 Remove the battery cover as shown in diagram 1 right 2 Install two AAA batteries as shown in diagram 2 right e Observe the polarity markings on the inside of the battery compartment 3 Replace the battery cover Using the remote e The supplied batteries are for operational checks and may not last as long as alkaline batteries e If the remote controllable distance begins to shorten replace both batteries with new ones e Direct sunlight or light from a high frequency fluorescent lamp may cause the remote sensor on the DT 7000S front panel to not function properly If this happens move the DT 70005 out of this direct light Activating your SIRIUS subscription Before you can listen to the DT 7000S you must subscribe to SIRIUS Satellite s service 1 Make sure that the DT 7000S is properly connected to your audio system and that the antenna is oriented to receive the SIRIUS satellite signal see pages 4 5 for details 3 Press the power button to turn the DT 7000S on After displaying the Kenwood and SIRIUS logos the display will read Acquiring Signal Once the SIRIUS satellite signal is received the display will change to Call 1 888 539 SIRIUS to Subscribe 4 If your DT 7000S has been properly connected and the antenna is
20. il the Antenna Signal screen appears right antenna Signal e After a few seconds the signal quality bars will indicate how well the antenna is receiving the SIRIUS satellite signal 2 Find a location for the antenna that illuminates the maximum number of bars Antenna Signal Screen e After moving the antenna wait at least 2 seconds before moving it again to enable the unit to process the signal 3 Due to the moving paths of the SIRIUS satellites it is possible for the signal to change over time In most cases signal should be available continuously however it may be temporarily blocked in some antenna locations in home installations Be sure to check the Antenna Signal screen if there is a loss of signal or audio Experimentation with antenna placement in the home or outside may be necessary to ensure continuous reception e See page 5 for information about properly locating the SIRIUS antenna DT 7000S Instruction Manual KENWOOD Troubleshooting guide No power on DT 7000S display not illuminated Power cord is not properly connected Make sure the power cord is properly connected Audio and or digital cable is not properly connected Make sure cable is properly connected Incorrect input selected on receiver controller Select the receiver controller input that the DT 7000S is connected to Signal is weak or can t be found Check the Antenna Signal screen see page 12 x mm Change the antenna location to maximize
21. ill scroll across the display If you want to listen to a different entertainment category turn the CATEGORY jog dial front panel or press the CAT buttons remote to activate the Category Select screen right and select entertainment categories Category Active Category 1 When the category you want is highlighted use the CH PRESET jog dial front panel or CH buttons remote to highlight streams 2 When the stream you want is highlighted press the ENTER button to listen to the stream The display will revert to the Normal Operation screen for that stream Stream Name Stream Number Category Select Screen e You can switch to the previously selected stream by holding the ENTER button for at least 1 second Holding the ENTER button for 1 second again switches back to the original stream e If no streams are available in a category or if all of the streams are set to be skipped or locked the display will read No Channels Available when that category is highlighted See Channel Skip Lock on pg 11 KENWOOD Selecting entertainment In addition to the Normal Operation and Category Select screens the DT 7000S has three ways to search for and select entertainment by stream by artist and by song Selecting entertainment by stream Stream List Mode 1 Press the ENTER button while in the Normal Operation mode The Stream List screen will appear showing all available streams regardless of category b
22. inity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Replacement parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts Unauthorized substi tutions may result in fire electric shock or other hazards Attachments Only use attachments specified by Kenwood with the DT 7000S Accessories Use only with the cart stand tripod or bracket recommended by Kenwood or sold with the DT 7000S Do not place the tuner on an unstable cart stand tripod bracket or table When a cart is used use caution when mov ing it to avoid tip overs that can cause injuries Qe KENWOOD Connecting the DT 7000S to your audio system Use the cables supplied with the DT 7000S to make these connections 00000000000 A 0000000000 din 90000000000 a o eee ele 200 u OO I F DIGITA OUT Ni OUT OFMMAL COMPATIBLE About the RS 232C gt Control 3RD PARTY connection RS 0990 Output CONTROLLER The RS 232C connection is cable provided to allow the NOTE DO NOT connect to DT 7000S to be controlled by a computer compatible 3rd party con
23. n X appears in the box on the display s fourth line if your local area does not observe Daylight Savings Time press the ENTER but ton so that the box is empty Press the SETUP button to exit Timer Functions GMT ESC ri Daylight Gaines Screen The DT 7000S has three Timer functions The Alarm turns the DT 7000S on at a specified time and to a specified stream Auto Shut Off automatically turns it off ata specified time and the Sleep Timer lets you listen to the DT 7000S for a specified peri od of time before it automatically shuts off Setting the Alarm 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Alarm Clock Setup screen appears right 2 Turn the CH PRESET jog dial unit or press the CH buttons remote The Step 1 Set Alarm Time screen appears lower right 3 Use the CH PRESET jog dial unit or press the CH buttons remote to set the hour you want the DT 7000S to turn on The alarm will auto matically switch from AM to PM 4 When the display shows the correct hour Set Alarm Time nm F 2 Am Off GA Enter gt HEHE to continue Step 1 Set Alarm Time Screen r turn the CATEGORY jog dial unit or press the CAT buttons remote to highlight the minutes Use the CH PRESET jog dial unit or press the CH buttons remote to set the minute you want the DT 000S to turn on DT 7000S Instruction Manual KENWOOD
24. n 2 Mount the antenna on a NORTHEAST or NORTH FACING wall or window Section 3 Mount the antenna on a NORTHWEST or NORTH FACING wall or window Section 4 Mount the antenna on a NORTHWEST or WEST FACING wall or window Section 5 Mount the antenna ONLY ON THE ROOF OR ON AN OUTSIDE WALL KENWOOD Controls and Features POWER Button Number Buttons CATEGORY Jog Dial Display MEMORY Button Preset Bank Indicators DISPLAY Button SEEK MODE Button CH PRESET Jog Dial 0 STANDBY Indicator Note Buttons on the unit and remote with the same name have the same function POWER Button unit only Turns the DT 7000S on and puts it into the Standby mode Power Off On Buttons remote only Emit discrete codes to turn the DT 7000S off and on Category Jog Dial unit CAT Buttons remote Puts the DT 7000S into the Category Select tuning mode and accesses different entertainment categories accesses differ ent selections in the Setup mode see pages 7 amp 10 Number Buttons Sets and selects stream presets selects alphanumeric charac ters for naming Preset Banks see pages 8 9 Preset Bank Indicators Shows which of the four Preset Banks is currently active MEMORY Button Saves amp recalls song amp artist information sets Lock Code number see pages 9 amp 12 DISPLAY Button Switches the display between different modes see page 1
25. ng Song Seek You can have the DT 7000S auto matically prompt you when any of the songs saved on the Song Memory List is playing on any E J Me ary List stream p md Bi a abe wot Sd geo eso p ov eee 0 1 Activate the Song Memory List Lille 3 Millio LI screen see previous section bandi La Bionda 2 Use the CH PRESET jog dial or CH ne Empty buttons to scroll through the list of Song Seek Icon saved songs until the one you want is highlighted 3 Press and release the ENTER button An S will appear next to the song s name above Press the MEMO button to exit KENWOOD 4 When one or more of the selected songs is playing on any stream an alert screen will be superimposed over the data on the original screen below e The number on the screen will count down from 10 to O To hear the song press the ENTER button before the counter reaches zero to make the alert screen dis appear press the SETUP button on the front panel The DT 7000S will switch to the stream that is playing the song Song Seek Alert Screen e If you do nothing the alert screen will disappear when the counter reaches zero Display options Changing display modes The Normal Operation Screen has two modes Normal and Large Font right Press the DISPLAY button to cycle the display between the two modes Adjusting the display brightness e Press the DIMMER button on the remote to cycle the di
26. nna loca tion is at a window D right Use an appropriate window depending on where you live refer to the map The location of the X onthe map must be visible to the antenna e Place the antenna midway between the left and right window frames e Tilt the hinged part of the antenna back to aim it towards the sky Note Objects such as the following can prevent the antenna from receiving the satellite signal when placed at a window or on an outside wall roof extensions ethe window frame metallic window screens or tinting objects in the window e nearby objects like trees foliage or buildings Ifthe signal is blocked from getting to the antenna the antenna must be relocated to a more appropriate window an outside wall free of obstructions or on the roof DT 7000S Instruction Manual STRAIGHT UP AIM ANTENNA ELEMENT AIM ANTENNA ELEMENT STRAIGHT UP OVERHANG CAN BLOCK SATELLITE SIGNAL MOUNT ANTENNA LOWER TO AVIOD OVERHANG AIM ANTENNA ELEMENT CLOSE TO STRAIGHT UP ae i OVERHANG CAN BLOCK SATELLITE SIGNAL PA Use this map as a general placement guideline some experimentation may be needed to obtain the best reception in your particular situation See pg 12 Antenna Signal for more information about using the antenna signal screen to aim the antenna If you live in Section 1 Mount the antenna on a NORTHEAST or EAST FACING wall or window Sectio
27. reen appears right 2 Turn the CH PRESET jog dial unit or press the CH buttons remote until the display shows amount of time you want DT 7000S to stay on after the last time a button is pressed before it automatically shuts off Press the SETUP button to exit e When Auto Shutoff is activated the screen will display a countdown warning 10 seconds before the DT 7000S shuts itself off Pressing any button during this countdown will cancel the Auto Shutoff process and restore normal operation Auto Shutoff Setup Screen DT 7000S Instruction Manual Sleep Timer You can program the DT 000S to play for 30 or 60 minutes and then automatically turn itself off 1 While listening to SIRIUS press the ENTER button to enter the Stream List mode 2 Then hold the ENTER button for at least 1 second The Timer Setup screen will appear right 3 Use the CH PRESET jog dial unit or the CH buttons remote to highlight the amount of time you want the DT 7000S to play before it shuts off 4 Press the ENTER button to confirm your selection and activate the Sleep Timer o Cancel IF TNT 55 ENTER Set Timer Setup Screen When the Sleep Timer is active the display will return to the Normal Operation screen e The display will appear as normal except that every three seconds the timer countdown will replace the stream number You can still change streams and display modes as normal without shutting the timer off
28. signal quality Display reads Acquiring Signal Metallic window screen is interfering with reception Move antenna to window with a non metallic screen The antenna is not connected Verify antenna connections Display reads Antenna Error The antenna or cable is faulty Replace antenna Display reads Call 1 888 539 SIRIUS to Subscribe SIRIUS subscription has not been activated Call SIRIUS to activate your subscription Display reads Invalid Channel Stream entered is invalid Select a different SIRIUS stream Turn the power off press the POWER button wait 5 10 seconds then turn the power on again Turn the unit s power off unplug the power cord from the wall outlet wait 5 10 seconds plug the power cord back into the wall outlet and turn the power back on DT 7000S operates erroneously Microprocessor error If the problem persists consult your Kenwood dealer Sound mutes intermittently Metallic window screen is interfering with reception Move the antenna to a window with a non metallic screen Specifications Analog Audio Output Level 1kHz Power Consumption Signal to Noise Ratio Dimensions THD Noise 1kHz Digital Audio Output DT 7000S Instruction Manual 13 KENWOOD DT 7000S Instruction Manual KENWOOD DT 7000S Instruction Manual 15 KENWOOD Internet www kenwoodusa com e mail inquiry kenwoodusa com 1 800 KENWOOD Main Office PO Box 22745 Long Beach CA 90801 5745
29. splay through the three brightness levels high medium low Setup Mode The Setup Mode lets you access and set up the following features SID SIRIUS ID Number Clock Alarm Channel Skip Lock Lock Code Setup Auto Shutoff Startup Mode Output Level Antenna Signal and Preset Bank Naming To enter the Setup Mode press the SETUP button SID When you first enter the Setup Mode the unit s unique 12 digit SIRIUS ID Number will be displayed right Clock Setup The DT 7000S has an automatic clock that receives its time signal as part of the SIRIUS satellite stream To set the clock you need to tell the DT 000S what time zone you live in and if your 016 12 00P E 2 local area observes Daylight Savings Time The Vault ROCK Jugalbandi Ca Normal Operation Screen Large Font Screen Sirius ID 000042117400 SIRIUS ID Screen 1 While in the Setup Mode turn the CATEGORY jog dial unit or press the CAT buttons remote until the Auto Clock Setup screen appears right 2 Turn the CH PRESET jog dial unit or press the CH buttons remote once and the Time Zone Setup screen appears middle right 3 Turn the CH PRESET jog dial unit or press the CH buttons remote until your time zone is highlighted then press the ENTER button e The screen will change to the Daylight Savings screen below right 3 If your local area observes Daylight Savings Time press the ENTER button so a
30. trol systems Kenwood recom mends that this connection only be used by experienced Optical digital cable ES professional system installers igita Input DO NOT connect the RS 232C RECEIVER connection to a computer it is or NOT COMPATIBLE with person Stereo audio cable Stereo PREAMP CONTROLLER al computers Analog Input f SIRIUS KENWOOD Optional KENWOOD CX SRH30 ANTENNA or equivalent 4 DT 7000S Instruction Manual KENWOOD Finding a location for the optional Kenwood CX SRH30 antenna Due to the paths of the SIRIUS satellites over the US the best location for the antenna will depend on what part of the country you live in the orientation of your home and the locations of any obstruc tions that could prevent the satellite sig nal from reaching the antenna The best antenna location is on the roof facing straight up A right e The location of the X on the map must be visible to the antenna The second best antenna location is on an outside wall B C right Use an appropriate wall depending on where you live refer to the map The location of the X on the map must be visible to the antenna e Mount the antenna facing as close to straight up as possible B right e To minimize interference caused by roof extensions mount the antenna as low on the wall as possible while avoid ing other obstructions C right The third best ante
Download Pdf Manuals
Related Search