Kenmore 110.4587 Washer User Manual
Contents
1. parts are needed for your washer call Sears Parts and Service Toli Free Number 1 800 366 PART 1 800 366 7278 Destroy the carton and plastic bags after the washer is unpacked Children might use them for play Cartons covered with rugs bedspreads or plastic sheets can become airtight chambers causing suffocation Place all materials in a garbage container or make materials inaccessible to children SUTIN The instructions in this manual and all other literature included with this washer are not meant to cover every possible condition and situation that may occur Good safe practice and caution MUST be applied when installing operating and maintaining any appliance Maximum benefits and enjoyment are achieved when ali the Safety and Operating instructions are understood and practiced as a routine with your laundering tasks2. IF YOU SMELL GAS Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building Clear the room building or area of all occupants gt Immediately call your gas supplier from a neighbor s phone Follow the gas suppliers instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier PRE INSTALLATION REQUIREMENTS Tools Required for Installation 1 4 in nut driver 3 8 in socket with ratchet 3 8 in open end wrench 7 16 in socket with ratchet 9 16 in open end wrench Channel lock adjustable pliers Carpenter s level ELECTRICAL REQUIREMENTS CIRCUIT Individual properly polarized and grounded 15 amp branch circuit fused with 15 amp time delay fuse or circuit breaker POWER SUPPLY 2 wire with ground 120 volt single phase 60 Hz Alternating Current OUTLET RECEPTACLE Properly grounded 3 prong receptacle to be located so the power supply cord is accessible when the washer is in an installed position GROUNDING REQUIREMENTS NOAPonw Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded 1 The washer MUST be grounded In the event of malfunction or breakdown grounding will
3. Installation Instructions Pre Installation Requirements ccseeeseee 2 Kenmore Siena IN E E 3 4 P 1 4 Tr Grounding Requirements csccecessseesseeees 2 ni N i LA Water Supply Requirements useen 2 Drain Requirements eesssssesssesseersserrsursenrsrenarne 2 Rough In Dimensions ceeceee rerai 3 Location Of Your Washer saesseeeseesrsrereerresereresss 4 Brayer toraa Lo AE E E A T EE 4 4 K k i A L Installation coeoeoeneeoeseessereseresirsssrserressreesnsssearses 5 eet Replacement PAM ccicxcsisceosescvesyercscnctveestsvarciest 5 Tumble Action Washer Before beginning installation carefully read these instructions This will simplify the installation and ensure the washer is installed correctly and safely Leave these instructions near the washer after installation for future reference NOTE The electrical service to the Washer must conform with local codes and ordinances and the latest edition of the National Electrical Code ANSI NFPA 70 Save These Instructions NN N t a a i i ee Sears Roebuck and Co Hoffman Estates IL 60179 U S A P N 131801800 9811 YYZ For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or loss of life Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance WEA TO DO
4. TALLATION CLEARANCES When installed in alcove or closet Sides Rear 0 in 0 cm Top 0 in 0 cm Front Console Model Top 15 in 38 1 cm Rear Console Model When installed in closet Front 1 in 2 54 cm Closet door ventilation required 2 louvered openings each 60 in 387 cm 3 in 7 6 cm from top and bottom of door UNPACKING 1 Cutthe shipping carton along the dotted line along the base of the unit 2 While in the carton carefully lay the washer on its back side D an FH 10 Remove the styrofoam base Carefully return the washer to an upright position and remove the carton Carefully move the washer to within 4 feet 122cm of the final location Remove the following from the back side of the washer 4 bolts 4 yellow plastic spacers 4 metal P clamps Remove the service panel from the front of the washer Remove the 4 nuts and 6 large washers that attach the 2 yellow shipping braces to the drum and the base Lift up on the drum and remove the braces a yellow ribbon surrounds the items to be removed These braces must be removed to allow the power supply cord to be released from the shipping ring Remove the large styrofoam block located under the drum Lift up on the drum tilt the base of the foam block inwards toward the rear of the washer until free then pull it out Remove and discard the yellow ribbon and label from the front of the washer 11 From the rear of the washer c
5. arefully pull out the power supply cord through the hole in the backsheet 12 Replace the service panel and screws NOTE If the washer is to be transported at a later date the shipping support hardware must be reinstalled to prevent shipping damage Retain the hardware in the plastic bag provided INSTALLATION Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog up the water valve screens Connect the inlet hose ends to the HOT and COLD water faucets tightly by hand then tighten another 2 3 turn with pliers Turn the water on and check for leaks NOTE Use only new hoses provided with this unit Carefully move the washer to its final location Rollers on the rear of the washer allow for easy movement in undercounter installations Gently lift up on the front of the washer and slide back NOTE Lifting up more than 1 8 will engage the rear legs Do not use the dispenser drawer or door to lift washer With the washer in its final position place a level on top of the washer if an undercounter installation no rocking of the washer should exist Adjust the front leveling legs up or down to ensure the washer is resting solid Turn the lock nuts on each leg up towards the base of the washer and snug with a wrench NOTE Keep the ieg extension at a minimum to prevent excessive vibration The farther out the legs are extended the more the washer will vibrate T
6. cm Maximum height 96 in 244 cm l l I I l l I l NOTE Drain hose attached to the washer can reach a 58 in 147 cm high standpipe For higher standpipe use hose P N 131461201 available from Sears Parts and Service If drain is less than 24 in 61 cm install a siphon break kit DIV 26110285320 available from Sears Parts and Service ROUGH IN DIMENSIONS 17 60 Under Counter 345 87 9 inch cm Adjustable Legs Roller Wheels UNDER COUNTER INSTALLATION if an under counter installation is desired the washer MUST have a top sheet kit installed P N 131445600 Kit is available from Sears Parts Department Custom sized countertop is required is Pd Bcd ige eas eS 2 fe RA pS Ba 3 seamen f inch cm Adjustable Legs Roller Wheels LOCATION OF YOUR WASHER DO NOT INSTALL YOUR WASHER 1 In an area exposed to dripping water or outside weather conditions The ambient temperature should never be below 60 degrees F 15 6 degrees C for proper washer operation 2 In an area where it will come in contact with curtains or drapes 3 Inan area garage or garage type building where gasoline of other flammables are kept or stored including automobiles 4 Oncarpet Floor MUST be solid with a maximum slope of 1 2 in per foot 1 27 cm per 30 5 cm To ensure vibration or movement does not occur reinforcement of the floor may be necessary IMPORTANT MINIMUM INS
7. he washer is designed to operate resting on its rear rollers If the floor is not level or is damaged the rear leveling legs may have to be extended For undercounter installations rear leg adjustment is accessible through the front service panel Form a U shape on the end of the drain hose with the hose pointed toward the drain Place ina laundry tub or standpipe and secure with the cable tie provided in the enclosure package NOTE ifthe drain hose is placed in a standpipe without forming a U shape a siphoning action could occur There must be an air gap around the drain hose A snug hose fit can also cause a siphoning action Cabie Tie 6 Plug the power cord into a grounded outlet NOTE Check to ensure the power is off at a circuit breaker fuse box before plugging the power cord into an outlet 7 Turn on the power at a circuit breaker fuse box 8 Read the Operating Instructions and Owner s Guide provided with the washer They contain valuable and helpful information that will save you time and money 9 Run the washer through a complete cycle Check for water leaks and proper operation 10 If your washer does not operate please review the Avoid Service Checklist in your Owner s Guide before calling for service 11 Place these instructions in a location near the washer for future reference NOTE A wiring diagram is located inside the washer on the service panel REPLACEMENT PARTS lf replacement
8. reduce the risk of electrical shock by a path of feast resistance for electrical current 2 Since your washer is equipped with a power supply cord having an equipment grounding conductor and a grounding plug the plug MUST be plugged into an appropriate copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances or in the absence of local codes with the National Electrical Codes ANSI NFPA 70 latest edition If in doubt call a licensed electrician DO NOT cut off or alter the grounding prong on the power supply cord in situations where a two siot receptacle is present it is the owner s responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle WATER SUPPLY REQUIREMENTS Hot and cold water faucets MUST be installed within 42 inches 107 cm of your washer s water inlet The faucets MUST be 3 4 inch 1 9 cm garden hose type so inlet hoses can be connected Water pressure MUST be between 10 and 120 pounds per square inch maximum unbalance pressure hot vs cold 10 psi Your water department can advise you of your water pressure The hot water temperature should be about 120 degrees F 49 degrees C DRAIN REQUIREMENTS 1 Drain capable of eliminating 17 gals 64 3 L per minute 2 Astandpipe diameter of 1 1 4 in 3 18 cm minimum 3 The standpipe height above the floor should be Minimum height 24 in 61
Download Pdf Manuals
Related Search