JVC WB-1550 Security Camera User Manual
Contents
1. CAUTION e Fogging may occur when there are drastic temperature changes In this case continue using without turning off the power e Pay attention when handling the desiccant in order to maintain its effectiveness e Do not remove it from the bag until you are about to use it Do not wet it or touch it with wet hands Assemble promptly upon adhering the desiccant Be sure to replace the desiccant during maintenance 2 Mount the lower housing Mount the lower housing that is dismantled in Step 2 t pg 10 to the main housing unit using the 3 Screw A M4 x 6 Do so by aligning the position marks of the lower housing and the main housing unit 3 Mount the gasket and gasket gland Mount the gasket and gasket gland that are dismantled in Step 1 pg 10 of the housing disassembly procedure to the lower housing using the 8 Screws B M4 CAUTION e During assembly ensure that wires and cables are not caught in the housing e Do not exert force unnecessarily on the gasket or twist it during mounting e Check to ensure that the gasket is in close contact with the camera Mounting the Housing to the wall Safety Wire Anchor Bolt M8 35 mm and above Washer Nut 1 Drill a hole into the wall Drill a hole 45 mm for inserting the connection cable Refer to left fig 2 Affix anchor bolts onto the wall Affix 4 anchor bolts M8 35 mm and above for attac2. Camera QE Mounting Bracket Connector Connector 4 y Connect to AC 24 V Output Cable To POWER INPUT DC 12 V Terminal of Ceiling Mount Press AC 24 V Output Cable J 5mm Sur Press Connector MO Main Board AC 24 V Output Cable lan 2 To POWER E INPUT DG a lt 12V Eat gt Terminal of 4 Ceiling Interior of Housing Mount Main Board Safety Wire Cover UL i i i eiling Mount 4 Screws Supplied M4 x 20 x 4 5 Camera Preparation 1 Dismantle the camera mounting bracket Loosen the screws on the camera mounting bracket M4 4 pcs using a driver to dismantle it 2 Dismantle the converter unit mounting bracket Loosen the screws on the converter unit mounting bracket M3 2 pcs using a driver to dismantle it 3 Mount the converter unit to the housing Clamp the converter unit using the converter unit mounting bracket followed by mounting it to the housing using the screws M3 2 pcs removed in Step 2 When mounting pay attention to the orientation of the converter unit as shown in the left diagram 4 Mount the camera mounting bracket Mount the camera mounting bracket dismantled in step 7 to the housing Mount it exactly to the original position Mounting Before mounting Remove the ceiling mount cover of the camera and guide the cables supplied with WB 1540 through the cover x For further details
3. OUTDOOR HOUSING WB 1540 INSTRUCTIONS WB 1550 For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No WB 1540 WB 1550 Serial No This instruction book is made from 100 recycle paper LST0267 001A These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances IMPORTANT SAFEGUARDS Onhwna N 10 11 12 13 14 15 16 17 18 Read all of these instructions Save these instructions for later use All warnings on the product and in the operating instructions should be adhered to Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not recommended by the appliance manufacturer as they may cause hazards Do not use this appliance near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool etc Do not place this appliance on an unstable cart stand or table The appliance may fall causing serious injury to a PORTABLE CART WARNING child or adult and serious damage to the appliance may fall causing serious injury to a child or adult and serious symbol provided by RETAC damage to the appliance Use only with a cart or stand recommended by the manufacturer or sold with the appliance Wall or shelf mou
4. s ceiling mount to the main housing unit Use the 4 screws supplied M4 x 20 to mount the ceiling mount to the main housing unit NOTE During mounting align the FRONT mark of the ceiling mount with the notch on the camera mount bracket of the main housing unit 5 Mount the camera to the ceiling mount Follow instructions in the manual of the camera in use to mount the camera to the ceiling mount Installation and Connection WB 1540 Assembling the Housing 1 Adhering the desiccant Use a tape to adhere the supplied desiccant to the interior of the lower housing CAUTION e Fogging may occur when there are drastic temperature changes In this case continue using without turning off the power e Pay attention when handling the desiccant in order to maintain its effectiveness Do not remove it from the bag until you are about to use it Do not wet it or touch it with wet hands e Assemble promptly upon adhering the desiccant e Be sure to replace the desiccant during maintenance 2 Mount the lower housing Mount the lower housing that is dismantled in Step 2 t pg 10 to the main housing unit using the 3 Screws A M4 x 6 Gasket Do so by aligning the position marks of the lower housing Q y and the main housing unit _ 3 3 Mount the gasket and gasket gland Mount the gasket and gasket gland that are dismantled in Gasket Gland Step 1 gt pg 10 of the housing disassem
5. please refer to the instruction manual of the camera in use 7 Connect the AC 24 V output cable to the converter unit Follow the procedures below to connect the AC 24 V output cable of the main board on the main housing unit to the converter unit Push both ends of the connector as shown in the left diagram to remove it from the supplied converter unit Cut the Y terminal of the AC 24 V output cable and peel off about 5 mm of the coating Push the arrow mark using tools such as a flat head screwdriver to insert the coating of the AC 24 V output cable into the connector Attach the connector to the converter unit 2 Mount the Y terminal of the converter unit to the ceiling mount of VN C625 Guide the Y terminal of the converter unit through the ceiling mount cover followed by connecting it to the POWER INPUT DC 12 V terminal of VN C625 s ceiling mount 3 Connect other cables Connect the necessary cables supplied with the housing coaxial video cable alarm signal cable LAN cable etc to the corresponding terminals on the ceiling mount CAUTION e Connect the communication cable to the alarm terminal if necessary In addition DC 12 V Power Cable is not in use on this system For safety reasons ensure to cut off any excess cable and bind using an insulating tape before use e For further details on connection please refer to the instruction manual of the camera in use 4 Mount the camera
6. prodotto contattare la sede comunale locale il servizio di smaltimento rifiuti domestici o il negozio in cui si acquistato il prodotto Lutente responsabile del conferimento dell apparecchio a fina vita alle appropriate strutture di raccolta pena le sanzioni previste dalla vigente legislazione sui rifiuti Per gli utenti aziendali Qualora si desideri smaltire questo prodotto visitare la nostra pagina web www jvc europe com per ottenere informazioni sul ritiro del prodotto valido solo nell Unione Per altre nazioni al di fuori dell Unione Europea Europea Qualora si desideri smaltire questo prodotto effettuare lo smaltimento in conformita alla normativa nazionale applicabile o alle altre leggi della propria nazione relative al trattamento delle apparecchiature elettriche ed elettroniche obsolete Getting Started Thank you for purchasing this product These instructions are for WB 1540U WB 1550U Before beginning to operate this unit please read the instruction manual careully in order to make sure that the best possible performance is obtained The compatible cameras for each housing are as follows e WB 1540 TK C625U E VN C625U e WB 1550 TK C676E TK C655E VN C655U Table of Contents Getting Started Table Of Contents 00 eeeeeeeseeeeeeeeeeeeseaeeeeeeeneeeeeteeeaeenaeenaees 4 Operating Precautions ooooiocccncccnnccccooccconcnonrncnancccnnnc nana nnnnn nos 4 System Example civic cdo 5 VN C625
7. cover of the camera and guide the cables supplied with WB 1540 through the cover x For further details please refer to the instruction manual of the camera in use 1 Connect the AC 24 V output cable to the camera Connect the AC 24 V output cable of the main board to the camera s ceiling mount bracket 2 Connect other cables Connect the necessary cables supplied with the housing coaxial video cable communication cable etc to the ceiling mount CAUTION e Connect the communication cable to the ALARM IN OUT and CONTROL terminals if necessary For safety reasons ensure to cut off any excess cable and bind using an insulating tape before use e For further details on connection please refer to the instruction manual of the camera in use e Ensure to bind connectors of LAN cables and DC 12 V Power Cable that are not in use with an insulating tape before use 3 Mount the camera s ceiling mount to the main housing unit Use the 4 screws supplied M4 x 20 to mount the ceiling mount to the main housing unit NOTE During mounting align the f FRONT Mark of the ceiling mount with the notch on the camera mount bracket of the main housing unit 4 Mount the camera to the ceiling mount Follow instructions in the manual of the camera in use to mount the camera to the ceiling mount Mounting the Camera VN C625 1 Screw M4 x 4 2 Screw M3 x 2 Converter Unit i Mounting Bracket
8. not in use with insulating tape x2 Power will not be supplied to this unit and the installed camera when the fuse on the main board burns out When this occurs please consult your nearby JVC dealer as exchange of fuse according to the rating 125 V 5 A will be required Installation and Connection WB 1540 Disassembling the Housing Screw A M4 x 6 x 3 Lower Housing Safety Wire CA ll p Gasket El 1 Ela Gasket Gland E Screw B M4 x 6 1 Dismantle the gasket and gasket gland Loosen the 6 Screws B M4 using a driver followed by dismantling the gasket and gasket gland from the lower housing x The 6 Screws B M4 cannot be totally removed from the gasket to prevent it from falling off 2 Dismantle the lower housing Loosen the 3 Screws A M4 x 6 using a driver followed by dismantling the lower housing from the main housing unit x The lower housing is connected to the main housing unit using a safety wire CAUTION Pay careful attention to store the dismantled parts and screws until assembly is complete to prevent them from being misplaced Mounting the Camera TK C625 Interior of Housing JVC Mark Notch Safety Wire Main Board AC 24 V Output Cable a Mark To POWER INPUT AC 24 V 48 2 2 4 Terminal of Ceiling Mount M4 x 20 x 4 4 Camera Screws Supplied Before mounting Remove the ceiling mount
9. al VN C625 CAUTION 1 Not in use on this system Ensure to bind both ends of cables that are not in use with insulating tape x2 Power will not be supplied to this unit and the installed camera when the fuse on the main board burns out When this occurs please consult your nearby JVC dealer as exchange of fuse according to the rating 125 V 5 A will be required TK C625 TK C655 and TK C676 Systems WB 1540 WB 1550 Power Cable DC 12 V gt Not in use on this system 1 LAN Cable Power Cable AC 24 V gt To Insulated AC 24 V Power Supply x1 lt Coaxial Cable DEO INPUT Communication Cable TO CAMERA WB 1540 WB 1550 Main Board LED1 To TB1 RM P2580 TB1 AC24V INPUT Connected Power Indicator Red light turns on during power supply To VIDEO OUT TO CCU Terminal To POWER INPUT AC 24 V Terminal ___ To CONTROL ALARM IN OUT Terminal Ceiling Mount of Combination Camera CAUTION e Ensure to turn of the power of devices in use before connecting e Refer to the instruction manual for the combination camera that is supplied with this unit as well during connection and installation x1 Not in use on this system Ensure to bind both ends of cables that are
10. and VN C655 Systems coccococccccoccocncocanancnnnnanonnnos 5 TK C625 TK C655 and TK C676 Systems occocccciccccccccc no 5 Installation and Connection WB 1540 Disassembling the HOUSING oonooccnncccnonnncnonaninnnonananana conan 6 Mounting the Camera concocccnnccncnnocinoncnoncnnncnoncnncnonarnncnnncnn nino 6 A OE 6 UNC rd 7 Assembling the HOUSING cocccconccnnnncnonncnannnanananana conocia nanaccnno 8 Mounting the Housing to the Wall oo oonnnnnnnnnnnnnonnccnnacaninno 8 Installation and Connection WB 1550 Disassembling the HOUSING oooconoccnncnccnonnnncnncnanncnana conan 10 Procedures Before Mounting the Camera 10 Mounting the Camera 11 TK C655 and TK C676 we UN CO ta 12 Assembling the HOUSING cooocccncccoccnoccnononnninaninccana nina nananinan 13 Mounting the Housing to the Wall o oocncocninnicnnocacinnninnnns 13 Others Specifications WB 1540 ae WB 1550hi iat Asahi ee eal Operating Precautions E Depending on the installation environment of this unit the life span of the attached camera may decrease significantly Give close attention to the installation location especially if used continuously under high temperature or in locations constantly exposed to direct sunlight W As the interior of this unit will heat up be sure to use San Disk industrial if loading the CF card to VN C625 E This unit may stop functioning properly due to natural hazards as it is to be i
11. ation about the take back of the product Other Countries outside the European Union If you wish to dispose of this product please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment Benutzerinformationen zur Entsorgung alter Ger te gung DEUTSCH E Hinweis Dieses Symbol ist nur in der Europaischen Union g ltig Europ ische Union Dieses Symbol zeigt an dass das elektrische bzw elektronische Ger t nicht als normaler Haushaltsabfall entsorgt werden soll Stattdessen sollte das Produkt zur fachgerechten Entsorgung Weiterverwendung und Wiederverwertung in bereinstimmung mit der Landesgesetzgebung einer entsprechenden Sammelstelle f r das Recycling elektrischer und elektronischer Ger te zugef hrt werden Die korrekte Entsorgung dieses Produkts dient dem Umweltschutz und verhindert m gliche Sch den f r die Umwelt und die menschliche Gesundheit welche durch unsachgem e Behandlung des Produkts auftreten k nnen Weitere Informationen zu Sammelstellen und dem Recycling dieses Produkts erhalten Sie bei Ihrer Gemeindeverwaltung Ihrem rtlichen Entsorgungsunternehmen oder in dem Gesch ft in dem Sie das Produkt gekauft haben F r die nicht fachgerechte Entsorgung dieses Abfalls k nnen gem der Landesgesetzgebung Strafen ausgesprochen werden Gesch ftskunden Wenn Sie dieses Produkt entsorgen m chten besuchen Sie bitte unse
12. bly procedure to the lower housing using the 6 Screws B M4 Position Mark Screw B M4 x 6 CAUTION S e During assembly ensure that wires and cables are not caught in the housing e Do not exert force unnecessarily on the gasket or twist it during mounting e Check to ensure that the gasket is in close contact with the camera Mounting the Housing to the wall O 1 Drill a hole into the wall M8 35 mm and above Drill a hole 45 mm for inserting the connection cable Refer to left fig Washer 2 Affix anchor bolts onto the wall Nut e Affix 4 anchor bolts M8 35 mm and above for attaching the housing Refer to left fig Affix an anchor bolts for attaching the safety wire in the middle about 60 mm from both ends of the 2 upper anchor bolts 30 mm from the top Refer to left fig 3 Mount the safety wire and arm to the wall Mount the safety wire attached to the housing to the anchor bolts using the nut and wire Use the nut and wire to mount the housing onto the wall e Mounting the Housing to the Wall continued Waterproofing __ Alarm Communication Cabl LAN Coaxial Video Cable Ac 24V Power Cable 8 A 4 D A A Cable Male X DC 12 V Power Cable Hole Waterproofing ik vi Bind with insulating tape X Not in use on this system Ul Bind using a waterproof adhe
13. e Wind Speed 40 m s or below E Compatible Cameras TK C676E TK C655E VN C655U E Dimensional Outline Drawing Unit mm 12 176 2 R9 hole x Specifications and appearance of this unit as well as related products may be modified for improvement without prior notice 15 2005 Victor Company of Japan Limited Printed in Japan LST0267 001A SNISNOH YHOOGLNO OSSI GM 0rSl aM
14. e subject to possible change without prior notice shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Information for Users on Disposal of Old Equipment ENGLISH Attention This symbol is only valid in the European Union European Union This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life Instead the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment recovery and recycling in accordance with your national legislation By disposing of this product correctly you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more information about collection point and recycling of this product please contact your local municipal office your household waste disposal service or the shop where you purchased the product Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation Business users If you wish to dispose of this product please visit our web page www jvc europe com to obtain inform
15. from the interior of the combination camera Turn the camera body cover in the direction as indicated in the left diagram When the camera body cover is tight and cannot be turned do so upon fastening the main unit Dismantle the camera body cover Dismantle the dome cover Remove the rubber gasket and restore the dome cover and camera body cover to their original positions CAUTION The combination camera is an enclosed unit In order to prevent fogging in the interior of the dome cover ensure to remove the rubber gasket 2 types before use e Do not remove the combination camera from the housing and use it singly after removing the rubber gasket and installing to the housing Doing so may cause the camera to malfunction Mounting the Camera TK C655 and TK C676 Interior of Housing JVC Mark Notch Safety Wire Main Board Cables Mark al Ceiling AC 24 V Output Mount Cable aoa OS Parag Screws Supplied 4 pcs To POWER INPUT AC 24 V Terminal of Ceiling Mount Camera 1 Connect the AC 24 V output cable to the camera Connect the AC 24 V output cable to the ceiling mount of the camera to be installed 2 Connect other cables Connect the coaxial video cable and communication cables alarm signal control terminal etc supplied with the housing to the ceiling mount CAUTION e Connect the communication cable to the ALARM IN OUT and CONTROL terminals if
16. he service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Upon completion of any service or repairs to this appliance ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition LAC WARNING For USA and CANADA TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE Y RISK OF ELECTRIC SHOCK Information for USA DO NOT OPEN This device complies with Part 15 of the FCC Rules Changes or modifications not approved by JVC could void the CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK user s authority to operate the equipment DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL INFORMATION FOR CANADA RENSEIGNEMENT POUR LE CANADA This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of Due to design modification data given in this instruction sufficient magnitude to constitute a risk of electric book ar
17. hing the housing Refer to left fig e Affix an anchor bolt for attaching the safety wire in the middle about 60 mm from both ends of the 2 upper anchor bolts 30 mm from the top Refer to left fig 3 Mount the safety wire and arm to the wall Mount the safety wire attached to the housing to the anchor bolts using the nut and wire Use the nut and wire to mount the housing onto the wall 13 Installation and Connection WB 1550 Mounting the Housing to the Wall continued Screw M3 x 12 x 4 Alarm Communication Cable Coaxial Video Cable LAN Cable Male AC 24 V X DC 12 V Power Cable Power Cable 8 Hole 1 Waterproofing M Bind using a waterproof yY adhesive tape 6 X Not in use on this system 14 4 Open the cable connection cover Use provided hexagon wrench to remove the 4 screws M3 x 12 from the cable connection cover to open it 5 Connect each cable Connect the necessary cables CAUTION e Ensure to bind connectors of LAN cables that are not in use with an insulating tape before use e Ensure to bind the DC 12 V Power Cable that is not in use on this system with insulating tape 6 Bind cable using a waterproof tape Upon connecting ensure to perform waterproofing procedures by binding the joint of each cable with a waterproof adhesive tape CAUTION For safety reasons turn on the power only upon connecting all cable
18. inal of the converter unit to the ceiling mount of VN C655 Guide the Y terminal of the converter unit through the ceiling mount cover followed by connecting it to the POWER INPUT DC 18 V terminal of VN C655 s ceiling mount 3 Connect other cables Connect the necessary cables supplied with the housing coaxial video cable alarm signal cable LAN cable etc to the corresponding terminals on the ceiling mount CAUTION e Connect the communication cable to the alarm terminal if necessary In addition DC 12 V Power Cable is not in use on this system For safety reasons ensure to cut off any excess cable and bind using an insulating tape before use e For further details on connection please refer to the instruction manual of the camera in use 4 Mount the camera s ceiling mount to the main housing unit Use the screws supplied 4 pcs to mount the ceiling mount to the main housing unit NOTE During mounting align the A mark of the ceiling mount with the notch on the camera mount bracket of the main housing unit 5 Mount the camera to the ceiling mount Follow instructions in the manual of the camera in use to mount the camera to the ceiling mount Assembling the Housing Safety Wire Desiccant Lower Housing Position Mark Gasket Gasket Gland seres B M4 x 8 7 Mount the desiccant Use a tape to adhere the supplied desiccant to the interior of the lower housing
19. inflig es en cas d limination incorrecte de ce produit conform ment a la l gislation nationale Utilisateurs professionnels Si vous souhaitez liminer ce produit visitez notre page Web www jvc europe com afin d obtenir des informations sur sa r cup ration Pays ne faisant pas partie de l Union europ enne Si vous souhaitez liminer ce produit faites le conform ment a la l gislation nationale ou autres r gles en vigueur dans votre pays pour le traitement des appareils lectriques et lectroniques usag s Informaci n para los usuarios sobre la eliminaci n de equipos usados CASTELLANO Fe Atencion Este simbolo solo es valido en la Union Europea Uni n Europea Este s mbolo indica que los aparatos el ctricos y electr nicos no deben desecharse junto con la basura dom stica al final de su vida til El producto deber llevarse al punto de recogida correspondiente para el reciclaje y el tratamiento adecuado de equipos el ctricos y electr nicos de conformidad con la legislaci n nacional Si desecha el producto correctamente estar contribuyendo a conservar los recursos naturales y a prevenir los posibles efectos negativos en el medio ambiente y en la salud de las personas que podr a causar el tratamiento inadecuado del producto desechado Para obtener m s informaci n sobre el punto de recogida y el reciclaje de este producto p ngase en contacto con su oficina municipal su servicio de recogida de basura dom s
20. iver to dismantle it 2 Dismantle the converter unit mounting bracket Loosen the screws on the converter unit mounting bracket M3 2 pcs using a driver to dismantle it 3 Mount the converter unit to the housing Clamp the converter unit using the converter unit mounting bracket followed by mounting it to the housing using the screws M3 2 pcs removed in Step 2 When mounting pay attention to the orientation of the converter unit as shown in the left diagram 4 Mount the camera mounting bracket Mount the camera mounting bracket dismantled in step 7 to the housing Mount it exactly to the original position Mounting Before mounting Remove the ceiling mount cover of the camera and guide the cables supplied with WB 1550 through the cover x For further details please refer to the instruction manual of the camera in use 7 Connect the AC 24 V output cable to the converter unit Follow the procedures below to connect the AC 24 V output cable of the main board on the main housing unit to the converter unit Push both ends of the connector as shown in the left diagram to remove it from the supplied converter unit Cut the Y terminal of the AC 24 V output cable and peel off about 5 mm of the coating Q Push the arrow mark using tools such as a flat head screwdriver to insert the coating of the AC 24 V output cable into the connector Attach the connector to the converter unit 2 Mount the Y term
21. n equipped with TK C625U E 20 C to 40 C when equipped with VN C625U Heater Operation Temperature Internal temperature Heater turns ON between 8 C 5 C Turns OFF between 20 C 5 C Ambient Humidity 35 to 90 Vibration Shock Locations without vibration shock Dustproof Waterproof IP66 x When combined with compatible camera Permissible Wind Speed 40 m s or below E Compatible Cameras TK C625U E VN C625U E Dimensional Outline Drawing Unit mm R260 x Specifications and appearance of this unit as well as related products may be modified for improvement without prior notice WB 1550 E General E Mass 4 8 kg Power Voltage AC 24 V 50 Hz 60 Hz Main Housing Unit E Accessories Power Consumption INSTrucCtiONS oococccoconoccconorononos 1 25 W During heater operating excluding A 1 camera Screw M4x20 occcccccccccccccciccs 4 Installation Location Hexagon Wrench 1 Outdoor general Ambient Temperature 20 C to 50 C when equipped with TK C676E TK C655E 20 C to 40 C when equipped with VN C655U Heater Operation Temperature Internal temperature Heater turns ON between 8 C 5 C Turns OFF between 20 C 5 C Ambient Humidity 35 to 90 Vibration Shock Locations without vibration shock Dustproof Waterproof IP66 x When combined with compatible camera Permissibl
22. necessary For safety reasons ensure to cut off any excess cable and bind using an insulating tape before use e For further details on connection please refer to the instruction manual of the camera in use e Ensure to bind connectors of LAN cables and DC 12 V Power Cable that are not in use with an insulating tape before use 3 Mount the ceiling mount of the camera to the main housing unit Use the 4 screws supplied to mount the ceiling mount to the main housing unit CAUTION During mounting align the A mark of the ceiling mount with the notch on the camera mount bracket of the main housing unit 4 Mount the camera to the ceiling mount Follow instructions in the manual of the camera to be installed to mount the camera to the ceiling mount 11 Installation and Connection WB 1550 Mounting the Camera VN C655 Screw M4 x 4 Screw M3 x 2 3 Converter Unit Mounting Bracket 1 Camera Mounting Bracket Main Housing Unit AA Connector To POWER INPUT DC 18 V Terminal of Ceiling Mount Connect to AC 24 V Output Cable AC 24 V Output Cable wT 5 ue Press Connector S Main Board AC 24V Output Cable 5mm Xe Connector tae 2 To POWER i INPUT DC a are ae 18 V ES Main Board Safety Wire 12 Preparation 1 Dismantle the camera mounting bracket Loosen the screws on the camera mounting bracket M4 4 pcs using a dr
23. nstalled outdoors To take photographs properly be sure to perform daily checks E Do not install this unit in locations with sharp temperature changes such as near air con compressors or exhaust pipes Condensation may occur inside the attached combination camera E To save energy switch off the system when not in use E For safety reasons special techniques are necessary for installation Consult your dealer regarding installation and ensure that it is carried out by a specialist E Be sure to mount the safety wire for safety purposes If it falls it may cause injury or accidents E Taking vibrations mass and wind force into account ensure to mount in a location with sufficient strength using solid anchor bolts If reinforced or spiral nuts are not tightened enough picture blurring may occur on the monitor screen due to vibration and in the worst case there is a danger of falling E Use at the voltage indicated A voltage other than that displayed may result in fire or electric shocks W This unit supports lightning conduction to the connection cable to some extent but not fully At installation locations where there may be a lightning hazard be sure to add an arrester to the connection cable or take other precautions E Do not dangle shake or hook objects If too much load is placed on top it may fall and cause injury or accidents H If a ball or bird hits this unit bringing about some sort of trouble consult yo
24. nting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn Slots and openings in the cabinet and the back or bottom are provided for ventilation and to insure reliable operation of the appliance and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the appliance on a bed sofa rug or other similar surface This appliance should S3125A never be placed near or over a radiator or heat register This appliance should not be placed in a built in installation such as a bookcase unless proper ventilation is provided This appliance should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company For appliance designed to operate from battery power refer to the operating instructions For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges Do not allow anything to rest on the power cord Do not locate this ap
25. pliance where the cord will be abused by persons walking on it Follow all warnings and instructions marked on the appliance Do not overload wall outlets and extension cords as this can result in fire or electric shock Never push objects of any kind into his appliance through cabinet slots as they mat touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the appliance Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Unplug his appliance from the wall outlet and refer servicing to qualified service personnel under following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the appliance c If the appliance has been exposed to rain or water d If the appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation e If the appliance has been dropped or the cabinet has been damaged f When the appliance exhibits a distinct change in performance this indicates a need for service When replacement parts are required be sure t
26. re Webseite www jvc europe com um Informationen zur R cknahme des Produkts zu erhalten Andere L nder au erhalb der Europ ischen Union Wenn Sie dieses Produkt entsorgen m chten halten Sie sich dabei bitte an die entsprechenden Landesgesetze und andere Regelungen in Ihrem Land zur Behandlung elektrischer und elektronischer Ger te Informations relatives l limination des appareils usag s l intention des utilisateurs FRAN AIS Attention Ce symbole n est reconnu que dans l Union europ enne Union europ enne Lorsque ce symbole figure sur un appareil lectrique et lectronique cela signifie qu il ne doit pas tre limin en tant que d chet m nager a la fin de son cycle de vie Le produit doit tre port au point de pr collecte appropri au recyclage des appareils lectriques et lectroniques pour y subir un traitement une r cup ration et un recyclage conform ment a la l gislation nationale En liminant correctement ce produit vous contriburez a la conservation des ressources naturelles et a la pr vention des ventuels effets n gatifs sur l environnement et la sant humaine pouvant tre dus a la manipulation inappropri e des d chets de ce produit Pour plus d informations sur le point de pr collecte et le recyclage de ce produit contactez votre mairie le service d vacuation des ordures m nag res ou le magasin dans lequel vous avez achet le produit Des amendes peuvent tre
27. s 7 Fasten the cables in the interior of the arm When waterproofing is complete insert the cables into the upper interior of the arm and fasten using a tape CAUTION When inserting the cables ensure that all cable connections are above the cable connection cover see dotted line in the left diagram Failure to do so may cause malfunctions due to penetration of rain water 8 Cover the hole and the mounting side of housing with waterproof seal After the cables have been connected cover the holes made in step 7 with waterproof seal With the Cable connection cover open put your hand in and cover the hole Cover the mounting side of the housing with waterproof seal NOTE Be sure to perform waterproofing Seepage of rainwater may result in malfunction 9 Close the cable connection cover When cable connection is complete close the cable connection cover and fasten the 4 screws M3 x 12 removed in step 4 using the provided hexagon wrench Others Specifications WB 1540 E General E Mass 5 0 kg Power Voltage AC 24 V 50 Hz 60 Hz Main Housing Unit E Accessories Power Consumption INSTruCtiONS oooocccoconoccconoronono 1 25 W During heater operation excluding DesiCCMiccccccicciccnnnncincnnnannnnnos 1 camera Screw M4x20 ecsesesssssssseeessee 4 Installation Location Hexagon wrench 1 Outdoor general Ambient Temperature 20 C to 50 C whe
28. sive tape 6 4 Open the cable connection cover Use provided hexagon wrench to remove the 4 screws M3 x 12 from the cable connection cover to open it 5 Connect each cable Connect the necessary cables NOTES e When connecting to TK C625 ensure to bind connectors of LAN cables that are not in use with an insulating tape before using e Ensure to bind the DC 12 V Power Cable that is not in use on this system with insulating tape 6 Bind cable using a waterproof tape Upon connecting ensure to perform waterproofing procedures by binding the joint of each cable with a waterproof adhesive tape CAUTION For safety reasons turn on the power only upon connecting all cables 7 Fasten the cables in the interior of the arm When waterproofing is complete insert the cables into the upper interior of the arm and fasten using a tape CAUTION When inserting the cables ensure that all cable connections are above the cable connection cover see dotted line in the left diagram 7 Failure to do so may cause malfunctions due to penetration of rain water 8 Cover the hole and the mounting side of housing with waterproof seal After the cables have been connected cover the holes made in step 7 with waterproof seal With the Cable connection cover open put your hand in and cover the hole Cover the mounting side of the housing with waterproof seal NOTE Be sure to perform wa
29. terproofing Seepage of rainwater may result in malfunction 9 Close the cable connection cover When cable connection is complete close the cable connection cover and fasten 4 screws M3 x 12 removed in step 4 using the provided hexagon wrench Installation and Connection WB 1550 Disassembling the Housing Screw A M4 x 6 x 3 a2 Lower Housing E gt S Safety Wi ih atety Wire toed Gasket 3 Gasket Gland Screw B M4 x 8 o 1 Dismantle the gasket and gasket gland Loosen the 8 Screws B M4 using a driver followed by dismantling the gasket and gasket gland from the lower housing x The 8 Screws B M4 cannot be totally removed from the gasket to prevent it from falling off 2 Dismantle the lower housing Loosen the 3 Screws A M4 x 6 using a driver followed by dismantling the lower housing from the main housing unit x The lower housing is connected to the main housing unit using a safety wire Procedures Before Mounting the Camera CY Rubber Gasket White Ceiling Mount Camera Body Cover Rubber Gasket Gasket 10 1 Dismantle the rubber gasket of the camera s ceiling mount Dismantle the rubber gasket white on the same side as the ceiling mount of the combination camera to be installed 2 Dismantle the rubber gasket in the interior of the camera Follow the procedures below to remove the rubber gasket
30. tica o la tienda en la que haya adquirido el producto De acuerdo con la legislaci n nacional podr an aplicarse multas por la eliminaci n incorrecta de estos desechos Empresas Si desea desechar este producto visite nuestra pagina Web www jvc europe com para obtener informaci n acerca de la retirada del producto Otros pa ses no pertenecientes a la Uni n Europea Si desea desechar este producto h galo de conformidad con la legislaci n nacional vigente u otras normativas de su pa s para el tratamiento de equipos el ctricos y electr nicos usados Informazioni per gli utenti sullo smaltimento delle apparecchiature obsolete I IANO E Attenzione Questo simbolo Union Europea Questo simbolo indica che lapparecchiatura elettrica ed elettronica a cui relativo non deve essere smaltita tra i rifiuti domestici generici alla fine della sua vita utile Il prodotto invece va consegnato a un punto di raccolta appropriato per il riciclaggio di apparecchiature elettriche ed elettroniche per il trattamento il recupero e il riciclaggio corretti in conformita alle proprie normative nazionali Mediante lo smaltimento corretto di questo prodotto si contribuir a preservare le risorse naturali e a prevenire potenziali effetti negativi sull ambiente e sulla salute umana che potrebbero essere provocati altrimenti da uno smaltimento inappropriato del prodotto Per ulteriori informazioni sul punto di raccolta e il riciclaggio di questo
31. ur dealer or the nearest Victor service center E Do not modify this unit yourself Accidents may result H Do not install in locations where there may be vibrations or impact If it falls it may cause injury or accidents E Regularly check for the deterioration of attaching parts and the loosening of the screws caused by vibrations If it falls it may cause injury or accidents H Do not install in locations where radiation X rays or corrosive gases are emitted Doing so may cause the camera to malfunction E Keep all packaging out of the reach of children If used for play it may cause injury or suffocation System Example VN C625 and VN C655 Systems WB 1540 WB 1550 iz Power Cable DC 12V Power Cable Not in use on this system 1 AC 24V mp AC 24 V Power Supply sd Coaxial Cable Monitor Alarm Cable WB 1540 WB 1550 Main Board Alarm Device LAN Cable o PC TB1 AC24V INPUT Connected TO CAMERA Power Indicator Red light turns on during power supply VN C625 655 applied Converter To VIDEO OUT Terminal To ALARM IN OUT Terminal To POWER INPUT DC 18 V E E i Terminal VN C655 aad ee f To 10 PASE T 100 BASE TX Terminal To POWER INPUT DC 12 V Ceiling Mount of Network Camera Termin
Download Pdf Manuals
Related Search