JVC GV-CB3E DVR User Manual
Contents
1. ENGLISH 0000 GLIS oo JVE HOME THEATER SOUND SYSTEM TH BAT Consists of CA THBA1 and SP THBA1 QX DOLBY DIGITAL S dts Digital Surround Thank you for purchasing a JVC product Before operation please read the instructions carefully For customer use Enter below the Model No and Serial No which are located either on the rear bottom or side of the cabinet Retain this information for future reference Model No Serial No INSTRUCTIONS evto289 018D C O0709WMKMDWJMM 2 en 2009 Victor Company of Japan Limited CAUTION CA THBA1 The button in any position does not disconnect the mains line Disconnect the mains plug to shut the power off completely the STANDBY lamp goes off The MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable When the System is on standby the STANDBY lamp lights red e When the System is turned on the STANDBY lamp goes off The power can be remote controlled CAUTION SP THBA1 The power supply to the subwoofer is linked to the center unit Disconnect the mains plug to shut the power off completely the POWER ON lamp goes off The MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable When the System is on standby the STANDBY ON lamp lights red When the System is turned on the STANDBY ON lamp lights bl2. Dimensions W x H x D Mass Powered subwoofer SP THBA1 Output power 100 W RMS at 3 Q at 45 Hz with 10 total harmonic distortion Type 1 Way Bass Reflex Type Speaker 16 cm 6 5 16 cone x 1 Power Handling Capacity 100 W Impedance 30 Frequency Range 45 Hz to 5 kHz Sound Pressure Level 82 dB Wem 15 cm 5 15 16 Kz RS 10 W 10 cm 3 15 16 SP THBA1 For CA THBA1 and SP THBA1 This device compiles with RSS 210 of Industry Canada Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Pour CA THBA1 et SP THBA1 Cet appareil est conforme au r glement CNR 210 de l industrie du Canada L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l utilisateur du dispositif doit tre pr t accepter tout brouillage radio lectrique re u m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif For Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE CAUSING EQUIPMENT STANDARD ENTITLED DIGITAL APPARATUS ICES 003 OF THE DEPARTMENT OF COMMUNICATIONS Pour le Canada CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQU
3. Veillez ce que sa ventilation correcte puisse se faire en le pla ant sur un support d au moins dix centim tres de hauter TH BA1 Front Face isem NV g gt 2em 13 16 NX 15 em 5 15 16 5 15 16 CA THBA1 For U S A Caution Changes or modifications not expressly approved by party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference ina residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experi
4. remote control or adjust the volume by pressing VOLUME Radio wave reflections The System is connected directly by radio waves which are reflected by walls furniture and buildings If the System cannot receive the waves properly move the System to obtain better reception Radio wave reception may also be interrupted by people moving between the units
5. core filter until it clicks shut CAUTION e Do not damage the cord by applying excessive force when winding r Setting up the subwoofer This System is equipped with a wireless subwoofer When you use it for the first time activate the wireless pairing Refer to the supplied information sheet Activate wireless pairing NOTE e The wireless pairing is not canceled even after the AC plug has been pulled out Troubleshooting If you have a problem with this System check this list for a possible solution before calling for service POWER Power does not come on The power cord is not inserted securely Plug it in securely REMOTE CONTROL The remote control does not work The battery is exhausted Replace the battery Sunlight is shining directly on the remote sensor Hide the remote sensor from direct sunlight The path between the remote control and the remote sensor on the front panel is blocked Point the remote control at the remote sensor on the front panel Signals cannot reach the remote sensor Move closer to the unit Pull out the insulation sheet SOUND Sounds are sometimes interrupted Radio wave connections may be interrupted Change the location and orientation of the speakers No sound from speakers The wireless connections have not been activated correctly Check the connection The sound has been turned off temporarily Press FADE MUTING on the
6. power or unplug it before installing the speakers Wait at least 30 minutes before turning on the TV s main power again e Ifthe TV is still affected move the speakers further away Typical installation Installing on the wall You can install the center unit on the wall Ex center unit Minimum 6 5 mm Maximum 10 mm Maximum 6mm b 4mm screw diameter Screw not supplied CAUTION e The center unit weighs approximately 3 5 kg 7 8lbs Sufficient care must be taken when installing it on the wall to prevent any accidents caused by its falling off e Use screws which are compatible with the strength and material of the pillar or wall to prevent the center unit from falling off OYA DIGITAL ANALOG INPUT SURROUND DOLBY SURROUND 1 2 1 2 PROLOGICI MODE C Sa ES OL I r Buttons and lamps on the front panel power button and STANDBY lamp Turns on off the System e STANDBY lamp lights up while the System is turned off Input button and input source indicator lamps Selects an input source DIGITAL 1 DIGITAL 2 or ANALOG e The indicator lamp for the selected input source lights up Surround button and surround indicator lamps Selects a surround mode SURROUND 1 SURROUND 2 or SURROUND OFF e The indicator lamp for the selected surround mode lights e The DOLBY PROLOGIC II lamp lights up when
7. surround is activated with an ANALOG input source selected surround is activated and a DIGITAL input source with 2 channel audio format Adjusting the volume Press VOLUME 0 to 40 e You can also use the volume buttons on the front panel CAUTION e Set the volume to the minimum level before starting any source If the volume is set to a high level the sudden blast of sound may damage your hearing and blow out the speakers Turning off the sound temporarily Press FADE MUTING e To restore the sound press the button again or adjust the volume Changing the display brightness Press DIMMER Each time you press the button the LED brightness changes as follows normal gt dim gt off Making sound clearer Only for Dolby DIGITAL and DTS You can enjoy low level recorded sound clearly even at a low volume level Dynamic Range Compression Press DRC Each time you press the button the sound is enhanced the effect as follows OF off gt MD middle MX maximum gt dd Dolby DTS PCM Digital i ft e Do not install the center unit onto a plywood or plasterboard wall otherwise it will fall and sustain damage e When installing the center unit on the wall Be sure to have them installed on the wall by qualified personnel Care must be taken when selecting a location for installation on the wall Injury to personnel or damage to equipment may result if the installed unit interfere
8. with daily activities AC adaptor should not be hanging put above of any other items It is acceptable to place the AC adaptor on the flat floor only Recommended mounting surface Wooden studs If the mount is to be installed on any surface other than wooden studs use suitable hardware which is commercially available r Connecting external components You can connect analog components to the ANALOG terminal and digital components to the DIGITAL 1 and DIGITAL 2 terminals 2 1 OPTICAL f DIGITAL IN t t t Red White i i i Digital optical cord RCA pin plug cord not supplied not supplied Analog component Digital components F ua Connecting the power cord Connect the supplied AC adaptor to the DC IN jack on the center unit Then connect the supplied AC power cord to the AC adaptor and plug it in a wall outlet e Plug in the power cord of the subwoofer to a wall outlet CAUTION e Disconnect the power cords before cleaning or moving the speakers T N VOLUME WE D BI NN es Remote sensor Receives the signal from the remote control Digital signal format lamps Shows the digital signal format of the incoming signal when DIGITAL 1 or DIGITAL 2 is selected as the input source Each lamp lights when DOLBY DIGITAL DTS PCM a Dolby Digital signal comes in a DTS signal c
9. ALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance gt Pour les Etats Unis ATTENTION RISQUE D LECTROCUTION NE PAS OUVRIR ATTENTION POUR EVITER TOUT RISQUE D ELECTROCUTION NE PAS OUVRIR LE BOITIER AUCUNE PIECE INTERIEURE N EST A R GLER PAR L UTILISATEUR SE R F RER UN AGENT QUALIFI EN CAS DE PROBL ME Le symbole de l clair l int rieur d un triangle quilat ral est destin alerter l utilisateur sur la pr sence d une tension dangereuse non isol e dans le boitier du produit Cette tension est suffisante pour provoquer l lectrocution de personnes Le point d exclamation l int rieur d un triangle quilat ral est destin alerter l utilisateur sur la pr sence d op rations d entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d instructions gt gt CAUTION Battery shall not be exposed to excessive heat such as sunshine fire or the like ATTENTION Les piles ne doivent en aucun ca
10. ES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR APPAREILS NUMERIQUES NMB 003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS For CA THBA1 and SP THBA1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the manufacturer for compliance could void the user s authority to operate the equipment Pour CA THBA1 et SP THBA1 Cet appareil est conforme la partie 15 des r gles de la FCC Federal Communications Commission Le fonctionnement est sujet aux deux conditions suivantes 1 Cet appareil ne peut pas causer d interf rences nuisibles et 2 cet appareil doit accepter toute interf rence recue y compris des interf rences qui peuvent causer un mauvais fonctionnement Tout changement ou modification non express ment approuv s par le fabricant pour conformit peut annuler l autorit de l utilisateur d utiliser l appareil European Union only Union europ enne seulement pid Power Requirements AC 120V 60 Hz Power Consumption 30 W during operation 1 00 W or less in Standby mode Dimensions W x H x D 215mm x 352 mm x 254mm 8 1 2 Xx 13 7 8 X 10 Mass 5 kg 11 Ibs Correspond
11. Replace only with the same or equivalent type For USA California Only This product contains a CR Coin Cell Lithium Battery which contains Perchlorate material special handling may apply See www dtsc ca gov hazardouswaste perchlorate Operations r Basic operation Turning on off the power Press 1 e You can also use the power button on the front panel NOTE e A small amount of power is consumed even when the power is turned off standby mode During standby mode the STANDBY lamp on the front panel lights up Unplug the power cord from the AC outlet to turn the power off completely e You can also turn on the System by pressing one of the input buttons DIGITAL 1 DIGITAL 2 or ANALOG Selecting the input source Press one of the input buttons DIGITAL 1 DIGITAL 2 or ANALOG D1 DIGITAL 1 D2 DIGITAL 2 or AN ANALOG appears on the display for 2 seconds e You can also use the input button on the front panel NOTE e The indicator lamp of the selected input source lights r Speaker layout Install the speakers on a flat and level surface to ensure the best sound quality e The sound may be affected depending on the location in which you install them To avoid such issues change the location and orientation of the speakers e Install the speakers leaving an appropriate distance between them e Ifyou install the speakers near the TV color distortion may occur To prevent this turn off the TV s main
12. ch consulter un vendeur ou un technicien radio TV exp riment pour obtenir de l aide e Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories e Manufactured under license under U S Patent numbers 5 451 942 5 956 674 5 974 380 5 978 762 6 487 535 and other U S and worldwide patents issued and pending DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS Inc 1996 2008 DTS Inc All Rights Reserved Specifications Center unit CA THBA1 Output power Center Front Surround 120 W 30 W per channel measure at 1 kHz Optical Digital In at full scale sinewave RMS at 4 Q at 1 kHz with 10 total harmonic distortion Audio section Analog Input ANALOG 1 Vrms 50 kQ Digital Input DIGITAL 1 DIGITAL 2 21 dBm to 15 dBm 660 nm 30 nm Speaker section Type Full Range Bass Reflex Type Magnetically Shielded Type Speaker 8 cm 3 3 16 cone x 4 Power Handling Capacity 30W Impedance 4Q Frequency Range Center Speakers 84 Hz to 22 kHz Front Speakers 84 Hz to 22 kHz Center Speakers 82 dB Wem Front Speakers 82 dB Wem Sound Pressure Level General Power Source DC IN AC adaptor AA R1902 DC19V 3 37 Input AC 110 240 V 1 5 0 9 50 60 Hz Output DC19 V 3 37 900 mm x125 mm x 85 mm 35 7 16 x 4 15 16 x 3 3 8 3 5 kg 7 8 Ibs
13. enced radio TV technician for help Pour les Etats Unis Attention Les changements ou les modifications qui ne sont pas explicitement approuv s par la partie responsable de l observance pourraient mettre fin au droit de l utilisateur d utiliser le mat riel Remarque Cet appareil a t test et il s est av r conforme aux limites applicables un appareil num rique de classe B en vertu de la Partie 15 des R gles de la FCC Ces limites sont con ues de mani re assurer une protection raisonnable contre les interf rences nuisibles dans une installation r sidentielle Cet appareil produit utilise et peut mettre une nergie de haute fr quence et s il n est pas install et utilis en conformit avec les instructions il peut causer des interf rences nuisibles aux communications radio Il n y a toutefois aucune garantie que des interf rences ne se produiront pas dans une installation particuli re Si cet appareil cause effectivement des interf rences nuisibles la r ception de la radio ou de la t l vision ce qu on peut tablir en mettant l appareil en marche et l arr t nous encourageons l utilisateur tenter de corriger l interf rence par une ou plusieurs des mesures suivantes r orienter ou d placer l antenne de r ception accro tre la s paration entre l appareil et le r cepteur brancher l appareil dans une prise ou un circuit autre que celui auquel le r cepteur est bran
14. ing to Linear PCM Dolby Digital and DTS with sampling frequency 32 kHz 44 1 kHz 48 kHz Designs amp specifications are subject to change without notice Getting started DO NOT connect the power cord until all other connections have been made r Prepare the Remote Control When you use the remote control for the first time pull out the insulation sheet Insulation sheet If the range or effectiveness of the remote control decreases replace the battery To Replace the Battery in the Remote Control Insert the battery into the remote control by matching the polarities and correctly Lithium coin battery product number CR2025 1 Pinch the side of the battery case BS 2 2 Pullout the battery case and insert the battery by matching the polarities NOTE e Store the battery in a place where children cannot reach Ifa child accidentally swallows the battery consult a doctor immediately e To prevent the battery from overheating cracking or starting a fire Do not recharge short disassemble or heat the battery or dispose of it in a fire Do not leave the battery with other metallic materials Wrap the battery with tape and insulate when throwing away or saving it e Do not poke the battery with tweezers or similar tools e Dispose of the battery in the proper manner according to federal state and local regulations CAUTION Danger of explosion if battery is incorrectly replaced
15. nt et suivre strictement les r gles et les lois locales sur la mise au rebut des piles e N exposez pas cet appareil la pluie l humidit un gouttement ou des claboussures et ne placez pas des objets remplis de liquide tels qu un vase sur l appareil For U S A WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE Pour les Etats Unis AVERTISSEMENT POUR PREVENIR LES RISQUES D INCENDIE OU DE CHOCS ELECTRIQUES NE PAS EXPOSER CE APPAREIL LA PLUIE OU L HUMIDIT Care of the cabinet e Stains on the System should be wiped off with a soft cloth If the System is heavily stained wipe it with a cloth soaked in water diluted neutral detergent and wrung well then wipe clean with a dry cloth e Since the System may deteriorate in quality become damaged or get its paint peeled off be careful about the following DO NOT wipe it forcefully DO NOT wipe it with thinners benzines or other organic solvents including disinfectants DO NOT apply any volatile substances such as insecticides to it DO NOT allow any rubber or plastic to remain in contact with it for a long time e Do not place anything on top of the System Doing so may cause the System to fall causing malfunctioning and or injury e The manufacturer accepts absolutely no liability for any accidents or damage resulting from inadequate assembly or mounting insufficient strength of attachmen
16. omes in a Linear PCM signal comes in Display Shows the volume level Volume buttons Adjusts the volume within the range of 0 to 40 r Adjusting the output level of the speakers You can adjust the output level within the range of 6 dB to 6 dB Press SPK LEVEL for the corresponding speaker SUBWOOFER Adjusts the output level of the subwoofer CENTER Adjusts the output level ofthe center speakers SURROUND Adjusts the output level ofthe front surround speakers r Using the surround mode You can listen to a more realistic sound than stereo sound using surround Available surround modes are as follows SURROUND 1 Suitable for the reproduction of multi channel sources 1 appears on the display when selected SURROUND 2 Suitable for the reproduction of any stereo music sources S2 appears on the display when selected e The indicator lamp of the selected mode lights Press SURROUND MODE 1 or SURROUND MODE 2 e To deactivate press OFF OF appears on the display r Using the core filter Attach the provided core filter to the power cord and the external components cord to reduce interference 7 Release the stopper of the core filter Stopper 2 Run the cable through the core filter and wind the cable firmly once inside the cutout of the core filter as shown in the External components cords You can wind two external components cords together 3 Close the
17. s tre expos es une chaleur excessive lumi re du soleil feu etc CAUTION To reduce the risk of electrical shocks fire etc 1 Do not remove screws covers or cabinet 2 Do not expose this appliance to rain or moisture ATTENTION Afin d viter tout risque d lectrocution d incendie etc 1 Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l appareil 2 Ne pas exposer l appareil la pluie ni l humidit CAUTION e Do not block the ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be able to get out e Do not place any naked flame sources such as lighted candles on the apparatus When discarding batteries environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed Strictly Do not expose this apparatus to rain moisture dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus ATTENTION e Ne bloquez pas les orifices ou les trous de ventilation Si les orifices ou les trous de ventilation sont bloqu s par un journal un tissu etc la chaleur peut ne pas tre vacu e correctement de l appareil e Ne placez aucune source de flamme nue telle qu une bougie sur l appareil e Lors de la mise au rebut des piles veuillez prendre en consid ration les probl mes de l environneme
18. t misuse or abuse or natural disasters If water gets inside the System Turn the System off and disconnect the power cord from the wall outlet then call the store where you purchased this System Using the System in this condition may cause a fire or electrical shock r Supplied accessories Check to make sure you have all of the supplied accessories If anything is missing contact your dealer immediately e Remote control RM STHBA1A X 1 e AC adaptor AA R1902 x 1 e AC power cord x 1 e Lithium coin battery CR2025 x 1 The battery has been installed in the remote control when shipped from the factory e Core filter x 2 CAUTION Proper Ventilation To avoid risk of electric shock and fire and to prevent damage locate the apparatus as follows 1 Front No obstructions and open spacing 2 Sides Top Back No obstructions should be placed in the areas shown by the dimensions below 3 Bottom Place on the level surface Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm 3 15 16 or more ATTENTION A ration correcte Pour pr venir tout risque de d charge lectrique ou d incendie et viter toute d t rioration installez l appareil de la mani re suivante 1 Avant Bien d gag de tout objet 2 C t s dessus dessous Assurez vous que rien ne bloque les espaces indiqu s sur le sch ma ci dessous 3 Dessous Posez l appareil sur une surface plane et horizontale
19. ue ATTENTION CA THBA1 La touche 5 1 dans n importe quelle position ne d connecte pas le syst me du secteur D connectez la fiche de secteur pour mettre l appareil compl tement hors tension le t moin STANDBY s teint La fiche secteur ou un coupleur est utilis comme dispositif de d connexion de l appareil et l appareil d connect doit tre pr t tre utilis Quand le syst me est en attente le t moin STANDBY est allum en rouge e Quand le syst me est sous tension le t moin STANDBY s teint L alimentation peut tre t l command e ATTENTION SP THBA1 L alimentation du caisson de grave est reli e l unit centrale D connectez la fiche secteur pour mettre l appareil compl tement hors tension le t moin POWER ON s teint La fiche secteur ou un coupleur est utilis comme dispositif de d connexion de l appareil et l appareil d connect doit tre pr t tre utilis e Quand le syst me est en attente le t moin STANDBY ON est allum en rouge Quand l appareil est sous tension le t moin STANDBY ON est allum en bleu Do not use another AC adaptor to connect this model N utilisez aucun autre ADAPTATEUR SECTEUR pour connecter ce mod le Introduction r Notes on handling Important cautions Installation of the System e Select a place which is level dry and neither too hot nor too cold between 5 C and 35 C 41 F and 95 F e Leave sufficient distance between the S
20. ystem and the TV e Do not use the System in a location near heat sources or in a place subject to direct sunlight excessive dust or vibration e Install the System in a location with adequate ventilation to prevent internal heat buildup Power cord e Do not handle the power cord with wet hands e small amount of power is always consumed while the power cord is connected to the wall outlet e Do not pull on the cord to unplug the power cord When unplugging the power cord always grasp and pull the plug so as not to damage the cord To prevent malfunctions of the System e There are no user serviceable parts inside If anything goes wrong unplug the power cord and consult your dealer e Do not insert any metallic objects or liquids into the System Safety precautions Avoid moisture water and dust Do not place the System in moist or dusty places Avoid high temperatures Do not expose the System to direct sunlight and do not place it near any heating devices When you are away When away on holiday or for other reasons for an extended period of time disconnect the power cord from the wall outlet Do not block the vents Blocking the vents may damage the System Warnings Cautions and_Others _ Vlises en garde precautions et For U S A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QU
Download Pdf Manuals
Related Search