Home

JVC GR-AXM50 Camcorder User Manual

1. Video Light When natural lighting is too dim you can brighten the scene by using the built in video light LIGHT OFF AUTO ON SET VIDEO LIGHT Set the LIGHT OFF AUTO ON as required ON Always keeps the light on as long as the camcorder is turned on AUTO Automatically turns on the light when the camcorder senses insufficient lighting on the subject OFF Turns off the light The video light can be used with the camcorder s power on t is recommended to set the white balance I pg 29 to indoor mode 3 amp when you use the video light When not using the video light turn it off to save battery power NOTES Even if the battery indicator does not blink in the LCD monitor or the viewfinder if the battery pack s charge is low the camcorder may turn off automati cally when you turn on the video light or when you start recording with the video light turned on When the LIGHT OFF AUTO ON switch is set to AUTO Depending on the lighting conditions the video light may keep turning on and off In this case manually switch the light on or off using the LIGHT OFF AUTO ON switch While the Sports or High Speed Shutter mode C pg 21 is engaged the light is likely to stay on e While the Twilight mode F pg 21 is engaged the light will not activate DANGER The video light can become extremely hot Do not touch it either while in operation or soon after tur
2. Manual Focus FAR NEAR NOTE You should already have made the necessary viewfinder 4 adjustments pg 10 If you haven t do so before continuing SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK ADJUST FOCUS To farther subject Press and hold FAR The Manual Focus indications 44 appear and 4 blinks Go to step 3 To nearer subject Press and hold NEAR The Manual Focus indications 2 appear and gt blinks Go to step 3 LOCK FOCUS Release FAR or NEAR The focus indication is replaced by the focus lock indication 42 and the adjusted focus is locked in RELEASE MANUAL FOCUS MODE Press FAR and NEAR simultaneously The Manual Focus mode is immediately released and the focus lock indication disappears NOTES e Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode If you focus in on a certain subject in the wide angle position sharply focused images cannot be obtained when zoomed up because the depth of field is reduced at longer focal lengths e When the focus level cannot be adjusted any farther or closer sk 2 will blink 24m EN NOV PICTURE STABILIZER LCD monitor or viewfinder To bright EE Exposure Level Indicator en the image _ _ __ _ __ ___ To darken the image RECORDING Advance
3. I gt pg 8 5 Diopter gt pg 10 Recording Start Stop Button 17 pg 15 17 POWER Switch pg 15 34 Recording Mode SP EP Select Button a irr teneret ep C pg 12 R A EDIT CANCEL Button CF pg 40 R A EDIT IN OUT Button gt pg 40 Tape Length T20 30 40 Select BUM d eei ette 17 pg 12 COUNTER R Reset M Memory B ttOD ese aei regne efe CF pg 35 Q EDIT Button pg 41 Q3 R A EDIT E pg 40 PICTURE STABILIZER Button CF pg 24 PROGRAM AE Select Dial gt pg 20 5 BRIGHT Dial VOLUME Dial Random Assemble Editing I pg 40 It is used to connect the camcorder to a device such as a personal computer For further detail consult your nearest JVC dealer External MIC jack capped 17 pg 45 DE IN Jackie iet gt pg 9 The jacks to are located beneath the jack cover VIDEO OUT gt pg 36 RF DC OUT Jack CF pg 36 AUDIO OUT Jack eee F pg 36 Indicators 33 Tally pg 15 34 Power On Indicator pg 15 Other Parts Video Eight z iere tee pg 19 Camera sensor Be careful not to cover thi
4. MM 459 Random Assemble Editing SET REMOTE VCR CODE R A Edit SET REMOTE TO OPERATE VCR Create edited videos easily using your Turn off the power to the VCR and point the remote camcorder as the source player You can select toward the VCR s infrared sensor Then referring to up to 8 cuts for automatic editing in any the VCR CODE LIST on the left press and hold MBR order you like R A Edit is more easily SET and press button A and then B performed when the optional RM V700U MBR Multi Brand Remote is set to operate with The code is automatically set once you release the your brand of VCR see VCR CODE LIST but MBR SET button and the VCR s power comes on can also be performed by operating the VCR ADEDATE TUE VW ED gt manually 4 a OPERATE THE VCR RM V700U CF pg 42 2 Make sure the VCR s power is on Then while holding VCR CTL press the button on the remote for the desired function The functions the remote can control are PLAY STOP PAUSE FF REW and VCR REC STBY you don t need to press VCR CTL for this one You re now ready to try Random Assemble Editing MBR SET IMPORTANT VCR CTL Although the MBR is compatible with JVC VCRs and those of many other makers it may not work with yours or may offer limited functions RM V700U optional NOTES e If the power doesn t come on in step 1 try another code from the VCR CODE LIST VCR CODE LIST e Some brands of VCR don
5. 1 Accessories To avoid personal injury Do not place this product on an unstable cart stand tripod bracket or table It may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Use a mounting accessory recommended by the manufacturer and follow the manufacturer s instructions for any mounting of the product Do not try to roll a cart with small casters across thresholds or deep pile carpets 2 Product and Cart Combination A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combina tion to overturn 3 Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 4 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 5 Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards PORTABLE CART WARNING Symbol provided by RETAC 6 Cleaning Unplug this product from the wall outlet before cleaning Do not
6. OR END RECORDING Press Recording Start Stop to end recording and engage fade or wipe out TO CANCEL FADE OR WIPE STANDBY MODE While gt Fade Wipe is displayed press SET twice OFF is displayed for approx 2 seconds and the reserved fade or wipe is cancelled Black Fader Fades in out to a black screen Mosaic Fader Gradually turns returns the picture into from a mosaic pattern Ey Shutter Wipe A black screen moves in from the top and bottom closing over the image like a shutter or a new image pushes open the black screen vertically from the center E Slide wipe A black screen moves in from the left to gradually cover the image or a new image moves in from right to left 26en LCD monitor or viewfinder Wide mode LCD monitor or viewfinder Title indication No indication Happy Birthday Our Vacation Merry Christmas A Special Day Happy Holidays Our New Wedding Day Congratulations y The characters you have set using Character Generator SET button PROGRAM AE select dial RECORDING Advanced Features cont Wide This feature allows you to record black bars at the top and bottom of the screen to produce a cinema like wide screen effect SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK SELECT FUNCTION 2 Press SEL repeatedly until Wide appears ENGAGE WIDE MODE
7. Rewind or Fast forward the tape Press REW to rewind or FF to fast forward the tape during Stop mode Adjust the brightness of the LCD monitor To brighten the image turn the BRIGHT dial toward To darken the image turn the dial toward Speaker volume control You can adjust the speaker volume by turning the VOLUME dial ADJUST VOLUME 1 If you want to turn up the volume Turn the dial toward If you want to turn down the volume Turn the dial toward NOTES e The camcorder shuts off automatically after about 5 minutes in Stop mode To turn on again set the power switch to POWER OFF then to PLAY e When the power switch is set to CAMERA and the LCD monitor is opened at an angle of 45 degrees or more the LCD monitor switches on and the viewfinder switches off automatically to save power e When the LCD monitor is turned off sound is not heard from the speaker e The playback picture can also be viewed in the viewfinder with the LCD monitor shut or on a connected TV gt pg 36 Camcorder operation is the same as described in this section You can also view the playback picture on the LCD moitor with it flipped over and retracted e During playback pressing DISPLAY lets you remove all indications from the screen PLAYBACK Features EN 3 5 FF STOP FEATURE PURPOSE Manual Tracking To eliminate noise bars that appear on the screen during playback 1 Press e
8. as shown For this AC plug adapter consult your nearest JVC dealer Plug adapter INFORMATION This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Change or modifications not approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encour aged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit diff
9. gt pg 27 Date Time 15 pg 11 CLOSE MENU 5 Press MENU The normal screen reappears NOTE The menu is available only in the Record Standby mode MENU Gain Up 5 To record a subject in a dark lit environment When it is more convenient to shoot the subject with a brighter image even if the picture becomes slightly coarse Automatically selected when the PROGRAM AE select dial is set to AUTO LOCK mode S LX Super LoLux To record a subject in a dimly lit environment When it is more convenient to shoot with a less coarse picture although the subject becomes slightly dark This setting is suitable for measuring sensitivity conforming to EIA 639 EIA Standard for Low Light Sensitivity Measurement EIA Electronic Industries Association Allows you to shoot dark scenes with no picture brightness adjustment Tele Macro Usually set to this position Usually the distance to a subject where the lens is in focus depends on the zoom magnification Unless there is a distance more than 1m to the subject the lens is out of focus at the maximum telephoto setting When set to ON you can shoot a subject as large as possible at a distance of approx 60 cm Depending on the zoom position the lens may go out of focus Interval Timer This feature allows you to set the parameters for Self Timer gt pg 32 and Time Lapse recording F pg 33 Rec Time This feature allows you to set the parameters for
10. DO NOT allow it to become wet EM drop the unit or strike it against hard objects ees subject it to shock or excessive vibration during transportation CS keep the lens directed at extremely bright objects for long periods qu direct the eyepiece of the viewfinder at the sun met carry it by holding the viewfinder or the LCD monitor Be sure to hold the main unit with both hands or use the grip oe swing it excessively when using the shoulder strap 5 This camcorder features a built in head cleaner which automatically cleans the heads and head drum when a cassette is loaded or unloaded If however the heads become dirty and cause blurriness or interruption in the playback picture consult your nearest JVC dealer LCD monitor 1 To prevent damage to the LCD monitor DO NOT T push it strongly or apply any shocks ss place the camcorder with the LCD monitor on the bottom 2 To prolong service life 85 avoid rubbing it with coarse cloth 3 Make be aware of the following phenomena for LCD monitor use These are not mulfunctions While using the camcorder the surface around the LCD monitor and or the back of the LCD monitor may heat up e If you leave power on for a long time the surface around the LCD monitor becomes hot About moisture condensation e You have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass outer surface This sa
11. indicator means that the battery pack has become hot Wait until it cools down to continue e The CHG indicator may not light properly with a brand new battery pack or with one that s been stored for an extended period In this case remove and reattach the battery pack and recharge it The CHG indicator should light during recharging If not contact your nearest JVC dealer DC OUT To AC outlet terminal AC Power Adapter Charger AA V11U DC cord To car s cigarette lighter socket Car Battery Cord AP V7U optional D Car Battery Charger Adapter BH V3U optional USING A CAR BATTERY Use the optional Car Battery Cord or Car Battery Charger Adapter connect as shown in the illustration to the left NOTES e When using the car battery leave the engine idling e The optional Car Battery Charger BH V3U can also be used to charge the battery pack e When using the optional Car Battery Charger or Car Battery Cord AP V7U refer to the respective instruction booklet USING AC POWER Use the AC Power Adapter connect as shown in the illustration to the left NOTE The supplied AC Power Adapter Charger features automatic voltage selection in the AC range from 110 V to 240 V GETTING STARTED cont Clock Lithium Battery Insertion Removal This battery is necessary for clock operation and to perform date time settings SWITCH OFF POWER Switch off the unit s power and remo
12. 3 Press SET RESTORE NORMAL SCREEN 4 Press SET again while Wide appears Instant Titles The camcorder has eight preset titles in memory You can superimpose one of them above a previously stored title as shown in the illustration to the left DISPLAY SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK SELECT FUNCTION 2 Press SEL repeatedly until Title appears SELECT PRESET TITLE Engage the Record Standby mode then press SET to cycle through the preset titles until the desired title is displayed NOTES To delete the Instant Title during recording press SEL repeatedly until Title appears then press SET To recall a title press SET again en2 MENU button 5 Character Generator You can enter an original title of up to 18 characters ACCESS MENU SCREEN Turn the PROGRAM AE select dial to any position except AUTO LOCK then press MENU ACCESS CHARACTER SET MENU Press or to move the highlight bar to Set Character then press NEAR The Character Set menu appears INPUT CHARACTERS Press FAR or NEAR to make the desired character blink then press MENU The selected characters appear at the bottom of the screen Repeat as many times as desired max 18 FAR NEAR To select the location of the next character press FAR or NEAR to make the row of squares blink at the bottom of the screen then press FAR or NE
13. 3 Press SET until MWB appears then press and hold SET for more than 3 seconds MWB blinks in the LCD monitor or the view finder during adjustment then stops blinking but stays lit when adjustment is complete PROGRAM AE select dial LCD monitor or viewfinder Tele Macro Interval Timer Rec Time JLIP ID NO Tally Set Character Date Time END MENU KEY Gain Up gt NORM Macro ON gt ON Interval Timer 1min Rec Time 12 JLIP ID NO Tally Set Character Date Time END MENU KEY If GAIN UP or TELE MACRO in the Menu has been changed from the factory settings this mark appears RECORDING Advanced Features cont Using Menu For Detailed Adjustment This camcorder is equipped with an easy to use on screen menu system that simplifies many of the more detailed camcorder settings SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK ACCESS MENU SCREEN 2 Press MENU SELECT FUNCTION Press or to place the highlight bar on the desired function MAKE SETTING The setting procedure depends on the function you select If you select Gain Up Tele Macro Interval Timer Rec Time JLIP ID NO or Tally press FAR or NEAR to cycle through the choices until the desired setting appears If you select Set Character or Date Time press NEAR to access the selection menu for each function Set Character
14. 8135 201 808 9279 770 339 2522 630 851 7855 5665 Corporate Avenue 10700 Hammerly Blvd Suite 110 2969 Mapunapuna Place Suite 101 Cypress CA 90630 4727 Houston TX 77043 2310 Honolulu 96819 2000 714 229 8011 713 935 9331 808 833 5828 230 Eliot Street 8192 West State Road 84 890 Dubuque Avenue Ashland MA 01721 2377 Davie FL 33324 4611 South San Francisco CA 94080 1804 508 881 5923 954 472 1960 415 871 2666 Sophisticated electronic products may require occasional service Just as quality is a keyword in the engineering and production of the wide array of JVC products service is the key to maintaining the high level performance for which JVC is world famous The JVC service and engineering organization stands behind our products NATIONAL HEADQUARTERS JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF US JVC CORP 107 Little Falls Road Fairfield NJ 07004 2105 If you ship the product Pack your JVC unit in the original carton or one of equivalent size and strength Enclose with the unit a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you received when you purchased your JVC unit Print your home return address on the outside and the inside of the carton Send to the appropriate JVC Factory Service Center as listed above Don t service it yourself CAUTION To prevent electrical shock do not open the To purchase accessories for y
15. Animation and Time Lapse recording I pg 33 JLIP ID NO This number is necessary when connecting the camcorder to a device such as a computer using the J terminal JLIP The numbers range from 01 to 99 Factory setting is 07 Tally ON The tally lamp comes on to signal the start of rcording OFF The tally lamp remains off at all times Set Character Allows you to input characters F pg 27 Allows you to set the current date and time pg 11 Factory setting and when the PROGRAM AE Select Dial is set to AUTO LOCK NOTE During shooting in low light Auto Focus accuracy may decrease even when Gain Up is used In this case use Manual Focus pg 23 MENU Interval Timer Indicator Rec Time Indicator LCD monitor or viewfinder Gain Up Tele Macro Interval Timer Rec Time JLIP ID NO Tally Set Character Date Time END MENU KEY 5s lt gt 15 1 25 4 gt 1 45 lt gt OFF 5min gt 1min gt 30s gt 15s 4 OFF RECORDING Advanced Features cont Self Timer You can set the delay between pressing the Recording Start Stop button and the actual start of recording If you secure the camcorder you or whomever is operating the camcorder can enter the scene before recording starts NOTE Make sure the camcorder is in the Record Standby mode before performing the following steps ACCESS MENU SCREEN Turn the PROGRAM AE select dial to any position e
16. Disp E 5 b d vsk E SS si al INDE B x Merry Christmas DEC 25 97 LCD monitor Viewfinder Indications AM 10 24 56 CD Cassette Warning Remaining iiio tereti rine C pg 15 When no cassette is inserted the Cassette Warning blinks When Erase Protection tab is not in the position that allows recording the Cassette Warning lights Otherwise the Remaining Tape Time is displayed When the Power switch is set to PLAY and a tape is loaded the Cassette mark is displayed regardless of the Erase Protection tab s position Recording Mode SP EP Indicator IF pg 12 8 PROGRAM AE Indicator gt pg 20 Displayed at 3 for approx 1 second when the PROGRAM AE select dial is switched from one position to another Then only the indicator remains at 8 O O Fade Wipe Standby Indicator 17 pg 25 Displayed at for approx 2 seconds when the Fade Wipe is switched from one function to another by pressing the SET button Then only the indicator remains at Program Manager Function Indication gt pg 25 Appears when the PROGRAM AE select dial is set to any position other than AUTO LOCK 5 Tape Length Display gt pg 12 Zoom Indicator 17 pg 18 D Recording Indicator G pg 15 Picture Stabilize
17. PLAY When the counter reaches 0 00 00 Audio Dubbing stops automatically and the camcorder enters the Audio Dub Standby mode END AUDIO DUBBING 4 Press STOP NOTES Do not press FF or REW during Audio Dub Standby or the edit points will not be accurate e If the microphone is too close to the TV or if the TV s volume is too high whistling or howling may occur NOTES for Insert Editing and Audio Dubbing e Insert Editing and audio Dubbing may not work correctly if the tape contains blank segments or if the recording speed was changed during the original recording e To edit dub onto a tape with the recording safety tab removed cover the hole with adhesive tape Do not press STOP during Insert Editing or Audio Dubbing or the edit points will not be accurate e During Insert Editing and Audio Dubbing when Insert Pause or Audio Dub Standby is engaged the counter may go slightly past 0 00 00 Recording however stops at exactly 0 00 00 46en LENS COVER After Use open close switch Set the power switch to POWER OFF to turn off the camcorder Press EJECT to open the cassette holder then remove the cassette Close and lock the cassette holder by pressing PUSH 4 Close and lock the LCD monitor Set to POWER OFF BATT RELEASE 5 Press BATT RELEASE to remove the battery pack Slide the LENS COVER open close switch to close the lens cover PUSH EJECT Cleaning Th
18. on the edited tape with certain VCRs 4 2 EN USING REMOTE CONTROL UNIT The Full Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations PLAY STOP PAUSE FF and REW of your VCR This remote control unit makes additional recording functions possible RM V705U provided BUTTONS RM V700U optional Installing The Battery PULL OUT BATTERY HOLDER Type 9 Pull out by inserting a pointed instrument into slot Type B Pull out while sliding the lock hole Type Pinch the release tab and pull out INSERT BATTERY Making sure the plus side is up insert the lithium battery CR2025 into the battery holder REPLACE BATTERY HOLDER Insert the battery holder into the remote control unit and push the holder until it clicks into place Read the caution concerning lithium batteries F pg 2 FUNCTIONS With the camcorder s power switch set to CAMERA With the camcorder s power switch set to PLAY O Infrared beam transmitting window Transmits the beam signal ZOOM T W Buttons Zoom in out I pg 18 O PLAY Button Playback start 17 pg 34 O STOP Button Stop I pg 34 O REW Button Retake rewind Quick Review F pg 18 Rew Rew Shuttle Search F pg 35 Q INSERT Button Insert Editing F pg 44 O START STOP Button Functions same as the Recording Star
19. purchase There are no other express warranties except as listed above THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT INCONVENIENCE LOSS OR ANY OTHER DAMAGES WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL INCLUDING WITHOUT LIMITATION DAMAGE TO TAPES RECORDS OR DISCS RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so these limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state JVC COMPANY OF AMERICA 41 Slater Drive DIVISION OF US JVC CORP Elmwood Park New Jersey 07407 REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY THIS WARRANTY DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT For customer use Enter below the Model No and Serial No which is located either on the rear bottom or side of the cabinet Retain this informat
20. recording tape s Erase Protection tab is missing Cover the hole with adhesive tape Some tapes have sliding tabs In this case check the position of the tab e The camcorder Power switch has not been set to CAM ERA gt pg 15 The TV has not been set to its VIDEO mode or channel If A V connection is used the TV s VIDEO TV switch has not been set to VIDEO The RF unit has not been set to the correct channel Noise bars appear in the playback e Manual Tracking has not been performed pg 35 picture Playback picture is blurred or The video heads are dirty or worn out Consult your interrupted nearest JVC dealer for head cleaning or replacement The counter indication is blurred e This is normal during Still playback TAPE TRANSPORT The tape stops during fast forward The Counter Memory Function has been activated or rewind gt pg 35 Rewinding or fast forwarding cannot e The tape is already fully wound on one reel or the other be performed 485 TROUBLESHOOTING cont OTHER The tape won t eject e The battery pack is running low e If the LCD monitor is not open over 45 degrees EJECT switch does not function Some functions are not available e The PROGRAM AE select dial is set to AUTO LOCK Vertical white lines appear when e This sometimes occurs when the contrast between the shooting a very bright object background and the object is great It is not a defect of th
21. remote control Each time INT TIME is pressed the Interval Timer indicator appears changing in the following order 15s 30s 1min 5min and No indication off 2 Release Instead of setting Interval Timer to OFF in the Menu press INT TIME on the remote control until the Interval Timer indicator disappears Animation 1 Set Instead of performing steps 1 and 2 on pg 33 Animation press REC TIME on the remote control Each time REC TIME is pressed the Rec Time indicator appears changing in the following order 1 4s 1 2s 1s 5s and No indication off 2 Release Instead of using the Menu in step 5 on pg 33 press REC TIME on the remote control until the Rec Time indicator disappears Time Lapse 1 Set Instead of performing steps 1 through 3 on pg 33 Time Lapse press INT TIME and REC TIME on the remote control Each time INT TIME is pressed the Interval Timer indicator appears changing in the following order 15s 30s 1min 5min and No indication off Each time REC TIME is pressed the Rec Time indicator appears changing in the following order 1 45 1 25 1s 5s and No indication off 2 Release Instead of using the Menu in step 5 on pg 33 press INT TIME and REC TIME on the remote control until the indicators disappear Also refer to pgs 32 and 33 Index Code Marking RM V700U only To give you automatic access to any selected point on a recording 1 Press VI
22. than 5 minutes to search for an in point the VCR s Record Pause mode is cancelled and editing doesn t take place e Pressing R A EDIT clears all in and out points from memory e Leave a small margin for error around each in point to ensure the scene is recorded in its entirety MM ad ORIGINAL TAPE camcorder 1 IN 0 3 2 UT IN OUT IN OUT A Ium ojola ris EDITED STOP AUTOMATIC EDITING TO VCR ENGAGE VCR S RECORD PAUSE MODE 1 Point the remote control toward the VCR s infrared sensor and press VCR REC STBY or manually engage the VCR s Record Pause mode BEGIN AUTOMATIC EDITING 2 Press EDIT on the camcorder and the previously selected scenes are copied to the VCR in the specified order While editing the R A Edit counter of the scene which is beging copied is shown with a blinking highlight END AUTOMATIC EDITING 3 When all selected scenes have been copied the camcorder and VCR enter the still or pause mode Press STOP on both units To make the R A Edit counter display disappear press R A EDIT When finished editing be sure to disconnect the editing cable and the audio video cable NOTES e If you performed step 1 C on page 39 MAKE CONNECTIONS keep the remote control pointed at the VCR during editing e The on screen display only appears while the camcorder searches for each scene e There may be noise at in or out points
23. type of power supply to your home consult your product dealer or local power company If your product is intended to operate from battery power or other sources refer to the operating instructions 3 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 4 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product EN 5 Ventilation Slots and openings in the cabinet are provided for ventilation To ensure reliable operation of the product and to protect it from overheating these openings must not be blocked or covered Do not block the openings by placing the product on a bed sofa rug or other similar surface Do not place the product in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 6 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer ANTENNA INSTALLATION INSTRUCTIONS 1 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection a
24. 118 W x 115 x 218 D mm 4 11 16 x 4 9 16 x 8 5 8 CAMERA Pick up 1 4 format CCD Lens F1 6 f 3 8 to 68 4 mm 18 1 power zoom lens with auto iris and macro control filter diameter 46 mm Viewfinder Electronic viewfinder White balance with 0 55 color LCD adjustment Auto Manual adjustment LCD MONITOR Size 3 diagonally measured LCD system LCD TFT active matrix system VIDEO Output 1 Vp p 75 ohms unbalanced via VIDEO out connector AC POWER ADAPTER BATTERY CHARGER AA V11U Power requirement U S A and Canada Other countries AC 120 60 HZ AC 110 V to 240 V 50 60 Hz Power consumption 23 W Output Charge DC 8 5 V zz 1 3 VTR DC 6 3 V 1 8 Charging system Constant current peak detection timer controlled Dimensions 150 W x 42 H x 68 D mm 5 15 16 x 1 11 16 x 2 11 16 Weight Approx 320 0 71 lbs CASSETTE ADAPTER C P7U Dimensions 188 W x 25 H x 104 D mm 7 7 16 x 1 x 4 1 8 Weight Approx 240 0 53 lbs Accessory AA R6 size battery x 1 Provided Accessories gt pg 6 Optional Accessories Battery Packs BN V12U BN V22U BN V25U Battery Charger BH V3U Battery Charger BH VC10U Car Battery Cord AP V7U RF Unit RF V5U Compact VHS C Cassettes TC 40 30 20 Active Carrying Bag CB V7U Wireless Remote Control Unit RM V700U Some acccesso
25. 43 GripsAdj stmernt cene ates pg 14 Tracking iicet ertet H Tripod Mounting e Twilight Mode sese High Speed Shutter Mode pg 21 V Es A Video Light ati pg 19 Index Code Marking pg 43 Viewfinder Adjustment pg 10 Insert Cassette n W Insert Editing Instant TItles 1 White Balance Adjustment L Wide cic rre tette mede LCD monitor Viewfinder indications pg 49 Z J ZOOMING pg 18 Journalistic shooting pg 17 NOS DANGER Video Light The video light becomes extremely hot Do not touch it either while in operation or soon after turning it off otherwise serious injury may result Do not place the camcorder into the carrying case immediately after using the video light since it remains extremely hot When operating keep a distance of about 30 cm 1 ft between the video light and people or object Do not use near flammable or explosive materials When using the AC Power Adapter Charger in areas other than the USA m The provided AC Power Adapter Charger features automatic voltage selection in the AC range from 110 V to 240 V USING HOUSEHOLD AC PLUG ADAPTER In case of connecting the unit s power cord to an AC wall outlet other than American National Standard C73 series type use an AC plug adapter called a Siemens Plug
26. AR to move the blinking cursor underneath the desired location Press when you re done and the blinking cursor returns to the character grid END CHARACTER SETTING Press FAR or NEAR to make End blink then press MENU twice to return to the normal screen PROGRAM AE select dial LCD monitor or viewfinder Gain Interval Timer Rec Time JLIP ID NO Date Time END MENU KEY NOTES To erase a character you entered mistakenly make Clear blink by pressing FAR or NEAR then press MENU All characters are deleted at once Or to erase selected characters only first move the blinking cursor to the character at the bottom row which you want to replace then press FAR or NEAR to highlight in the top left corner and then press MENU e To display the characters you have set Instant Title 34 gt pg 26 or Date Time Character Insert OL soooo0000000000 7 pg 28 e Characters may be set only in the Record Standby nd Clear ode o m m z c o MANTE NVQ bo ow oc O20 I oe co O lt ru to Coxzo a 2 lt Om r MCAD m 2 44 o z m z c m lt O lt ru 19 4 Ep Ten FAN U TIES NVQ LOO c 2 O20 I co MCRD N 0 0 48 Clear m o Acr 28 EN RECORDING Advanced Features cont LCD monitor or vi
27. CD monitor may be difficult to see If this happens we recommend that you use the viewfinder pg 15 For other notes refer to pg 15 en 7 Journalistic shooting In some situations different angles of shooting may be required for more dramatic results OPEN LCD MONITOR 1 Make sure the LCD monitor is fully open TILT LCD MONITOR Tilt the LCD monitor in the most convenient direction The LCD monitor can rotate almost full circle 270 90 downward 180 upward Self recording You can shoot yourself while viewing your own image in the LCD monitor TILT LCD MONITOR UPWARD Open the LCD monitor and tilt it upward to 180 degrees so that it faces forward START RECORDING 2 Point the lens toward yourself and start recording During self recording the monitor image and indications do not appear inverted as when viewing a mirror Brightness control You can adjust the brightness of the LCD monitor by turning the BRIGHT dial ADJUST BRIGHTNESS 1 If you want to brighten the image Turn the dial toward If you want to darken the image Turn the dial toward BRIGHT dial Y MES 59 i ZE y 97 Zoom out Zoom indicator bar Zoom Level indicator RETAKE R F FEATURE PURPOSE OPERATION NOTES FEATURE PURPOSE OPERATION NOTE FEATURE PURPOSE OPERATION NOTE Zooming To produce the zoom in o
28. EAR to move the highlight bar to Cancel then press MENU elf you re satisfied with the settings go on to step 5 START CLOCK OPERATION Once you ve set the date and time press FAR or NEAR until Set begins to blink then press MENU The Menu screen reappears CLOSE MENU 6 Press MENU PROGRAM AE select dial LCD monitor or viewfinder Gain Up Interval Timer Rec Time JLIP ID NO Tally Menu Screen Set Character Date Time END MENU KEY NOTES e To display the date and time in the LCD monitor or the viewfinder and on a connected TV see Date Time Insert F pg 28 e If in step 4 you input an invalid date FEB 30 JUN 31 Set Time and etc and perform step 5 Input Error appears blinking Date Screen 1 00 AM 12 00 at the bottom of the screen Press FAR or NEAR to input the correct number Set Date Month Day Year Time 12 hour indication with AM or PM 128 GETTING STARTED cont T20 30 40 tape length select button Tape Length Setting Set the tape length according to the length of the tape used SET LENGTH 1 Press T20 30 40 until the required indication appears in the LCD monitor or the veiwfinder T20 20 minutes of recording time T30 30 minutes and 40 40 minutes in SP NOTE The tape remaining time pg 15 displayed the LCD monitor or the viewfinder is correct only if the correct tape length has be
29. JVC MM COMPACT VHS CAMCORDER GR AXM5O Compact VHS VHSTH Enter below the Model No and Serial No which is located on the bottom of cabinet Retain this information for future reference INSTRUCTIONS LYT0002 0L1A Dear Customer Thank you for purchasing the JVC Compact VHS camcorder Before use please read the safety information and precautions contained in the following pages to ensure safe use of your new camcorder Using This Instruction Manual All major sections and subsections are listed in the Table Of Contents gt pg 7 Notes appear after most subsections Be sure to read these as well Basic and advanced features operation are separated for easier reference It is recommended that you see refer to the Index 17 pgs 49 52 and familiarize yourself with button locations etc before use nh read thoroughly the Safety Precautions and Safety Instructions that follow They contain extremely important information regarding the safe use of your new camcorder You are recommended to carefully read the cautions on pages 53 and 54 before use SAFETY PRECAUTIONS y RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to al
30. PLAYBACK Basic Connections To AUDIO and When VIDEO connectors connecting the cables open the jack cover Audio and Video cables optional To AUDIO and VIDEO IN connectors Antenna ANA VIDEO and RF DC OUT connectors RF unit RF V5U optional NOTES e lt is recommended to use the AC Power Adapter Charger as the power supply instead of the battery pack e To monitor the picture and sound from the camcorder without inserting a tape set the camcorder s Power switch to CAMERA then set your TV to the appropriate input mode e If you have a TV or speakers that are not specially shielded do not place the speakers adjacent to the TV as interference will occur in the camcorder playback picture There are three basic types of connections When making the connections refer also to your VCR and TV instruction manuals Connection To VCR A Editing Dubbing and Playback NOTE Use the optional Audio and Video cables CONNECT CAMCORDER TO VCR 1 As shown in the illustration at left connect the Audio and Video cables between the AUDIO and VIDEO connectors on the camcorder and those on the VCR SUPPLY POWER 2 Turn on the camcorder the VCR and the TV SELECT MODE Set the VCR to its AUX input mode and set the TV to its VIDEO mode Connection To A TV With A V Input Connectors B Play
31. SS once to place the index code INDEX blinks in the LCD monitor or the viewfinder during marking If VISS is pressed during Record Standby mode the mark is placed where START STOP is pressed 44m USING REMOTE CONTROL UNIT cont COUNTER R M Tape Counter Insert editing indicator LCD monitor or viewfinder oH 09 0 0O DIODOS RM V705U provided RM V700U optional Insert Editing You can record a new scene into a previously recorded tape replacing a section of the original recording with minimal picture distortion at the in and out points The original audio remains unchanged NOTE Use the RM V705U or RM V700U remote control unit to perform this procedure SELECT MODE 1 Set the Power switch to PLAY FIND EDIT OUT POINT Play back the tape locate the point and press PAUSE on the camcorder or the remote control RESET COUNTER Press and hold COUNTER R M for more than 2 seconds to reset the tape counter then press for less than 1 second and make sure M appears in the LCD monitor or the viewfinder FIND EDIT IN POINT Press REW to go a little beyond the beginning of the scene you want to replace press PLAY to view the recorded tape and press PAUSE at exactly at the point where the new scene should start ENGAGE INSERT EDITING MODE Press and hold INSERT and without releasing INSERT press and release PAUSE The Insert mode is engaged When the scene the ca
32. TING A VIDEO CASSETTE MONITOR OPEN El Slide MONITOR OPEN to open the LCD monitor Open to an angle of over 45 degrees Press EJECT to open the cassette holder El insert a video cassette Press PUSH to close the cassette holder For more details pg 13 SHOOTING LENS COVER open close knob E Recording Start Stop button El Slide the LENS COVER open close knob to open the lens cover Set the power switch to CAMERA The power indicator will light and an image will appear in the LCD monitor or the viewfinder El Press the Recording Start Stop button Recording starts To stop recording temporarily momentarily press the Recording Start Stop button once again For more details pg 15 16 The viewfinder switches off automatically to save power when the LCD monitor is opened at an angle of over 45 degrees The LCD monitor turns on off when it is opened closed at approx 45 degrees OA MAJOR FEATURES REMEMBER Integrated Auto Light The Logical Choice p HT Compact VHS E VASIH a gp lol _ BEE The only compact video that can be used with your VHS VCR with VHS Playpak Program AE with Special Effects gt pg 20 m Auto Mode Lock Auto Mode Release m Electronic Fog Filter ND Effect m Sepia m Twilight m Sports m 1 1000 sec High Speed Shutter m 1 2000 sec High Speed Shutter Zoom out Random Assemble Editin
33. TING STARTED This camcorder s 3 way power supply system lets you choose the most appropriate source of power NOTES No function is available without power supply Use only specified power supply e Do not use provided power supply units with other equipment CHARGING THE BATTERY PACK SUPPLY POWER Connect the charger s AC power cord to a wall outlet The power indicator lights ATTACH BATTERY PACK Align the marks and slide the battery pack in the direction of the arrow until it locks in place The CHG indicator lights DETACH BATTERY PACK When charging is completed the END indicator lights Slide the battery pack opposite the direction of the arrow BATT PACK CHARGE DISCHARGE BN V11U approx 1 hr 10 min approx 3 hrs 30 min BN V12U BN V22U approx 1 hr 10 min approx 2 hrs 10 min approx 3 hrs 30 min approx 7 hrs BN V25U approx 2 hrs 40 min USING THE BATTERY PACK ATTACH BATTERY PACK Hook its top end to the camcorder and push the battery pack in until it locks in place DETACH BATTERY PACK 2 Slide BATT RELEASE and pull out the battery pack approx 10 hrs Approximate recording time unit min BATT PACK Viewfinder off LCD monitor on LCD monitor off Viewfinder on BN V11U 50 30 50 35 BN V12U 50 30 50 35 BN V22U BN V25U 105 70 140 95 when the light is o
34. This product has been engineered and manufactured to assure your personal safety In order not to defeat the built in safeguards observe the following basic rules for its installation use and servicing ATTENTION Follow and obey all warnings and instructions marked on your product and its operating instruc tions For your safety please read all the safety and operating instructions before you operate this product and keep this manual for future reference INSTALLATION 1 Grounding or Polarization A Your product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug B Your product may be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 2 Power Sources Operate your product only from the type of power source indicated on the marking label If you are not sure of the
35. abaci n El Deslice la perilla de abertura cierre LENS COVER para abrir la tapa del objetivo Adjuste el interruptor de alimentaci n en CAMERA El indicador de alimentaci n se encender y aparecer una imagen en el monitor LCD o en el visor El Presione el bot n inicio parada de grabaci n Comenzar la grabaci n Para detener temporariamente la grabaci n presione nuevamente el bot n de inicio parada de grabaci n Por m s detalles 7 15 16 El visor se desconecta autom ticamente para ahorrar energ a cuando el monitor LCD es abierto a un ngulo mayor de 45 grados El monitor LCD se activa desactiva cuando se lo abre cierre a 45 grados aprox DOEN HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE 1 800 252 5722 Dear customer In order to receive the most satisfaction from your purchase read the instruction booklet before operating the unit In the event that repair is necessary or for the address nearest your location please refer to the factory service center list below or within the Continental United States call 1 800 252 5722 for your authorized servicer Remember to retain your Bill of Sale for Warranty Service JVC JVC SERVICE amp ENGINEERING COMPANY OF AMERICA DIVISION OF US JVC CORP FACTORY SERVICE CENTER LOCATIONS 107 Little Falls Road 1500 Lakes Parkway 705 Enterprise Street Fairfield NJ 07004 2105 Lawrenceville GA 30243 5857 Aurora IL 60504
36. asic Recording EN 1 5 1 ining time indicat o SEE You should already have performed the procedures listed min below If not do so before continuing Now calculating e Power F pg 8 e Tape Length Recording Mode Setting gt pg 12 120min e Grip Adjustment pg 14 LOAD A CASSETTE 1 First slide MONITOR OPEN and open the LCD i monitor to an angle of over 45 degrees Power indicator Bul Press EJECT to open the cassette holder then insert the cassette with the label facing out Press PUSH to ensure the holder is closed and locked 1 19min 2min Blinking 3 Shooting while watching the viewfinder ENTER RECORD STANDBY MODE Omin Blinking Make sure the LCD monitor is closed and locked Slide the LENS COVER open close switch to open the lens cover then set the power switch to 1min Blinking CAMERA The power indicator lights and the camcorder LENS COVER enters the Record Standby mode Switch The scene you re aimed at appears on the viewfinder screen with the word PAUSE DISPLAY button superimposed upon it START SHOOTING 3 Press the Recording Start Stop button Start St The tally lamp lights while recording is in progress and appears in the viewfinder STOP RECORDING 4 Press the Recording Start Stop button again to stop recording Tally lamp The camcorder re enters the Record Standby mode NOTES e When
37. assette from the middle use the RETAKE function F pg 18 to find the end of the last recording so you don t erase any of it e The LENS COVER warning blinks for about 5 seconds when the camcorder is turned on when the cover is closed e While shooting sound is not heard from the speaker 1 6 EN RECORDING Basic Recording cont LENS COVER Switch MONITOR OPEN Tape remaining time indicator min Now calculating 120min 119min 3min 3 2min Blinking 1min Blinking Omin Blinking Tally lamp Shooting while watching the LCD monitor Before the following steps perform step 1 I pg 15 ENTER RECORD STANDBY MODE Make sure the LCD monitor is fully open Slide the LENS COVER open close switch to open the lens cover then set the power switch to CAMERA The power indicator lights and the camcorder enters the Record Standby mode The scene you re aimed at appears in the LCD monitor with the word PAUSE superimposed upon it START SHOOTING 3 Tilt the LCD monitor upward downward for best viewability pg 17 and press the Recording Start Stop button The tally lamp lights while recording is in progress and appears in the LCD monitor STOP RECORDING 4 Press the Recording Start Stop button again to stop recording The camcorder re enters the Record Standby mode NOTES e When you use the LCD monitor outdoors in direct sunlight the L
38. aters or other heat sources Et out of direct sunlight eds where they won t be subject to unnecessary shock or vibration bey where they won t be exposed to strong magnetic fields such as those generated by motors transformers or magnets B vertically in their original cases Main Unit 1 For safety DO es open the camcorder s chassis EM disassemble or modify the unit e short circuit the terminals of the battery pack Keep it away from metallic objects when not in use m allow inflammables water or metallic objects to enter the unit eus remove the battery pack or disconnect the power supply while the power is on shee leave the battery pack attached when the camcorder is not in use 2 Avoid using the unit we in places subject to excessive humidity or dust sey in places subject to soot or steam such as near a cooking stove T in places subject to excessive shock or vibration eus near a television set near appliances generating strong magnetic or electric fields speakers broadcasting antennas etc eee in places subject to extremely high over 40 C or 104 F or extremely low under 0 C or 32 F temperatures 3 DO NOT leave the unit pum in places of over 50 C 122 F e in places where humidity is extremely low below 35 or extremely high above 80 in direct sunlight s in a closed car in summer v near a heater CAUTIONS cont 4 To protect the unit
39. ations e In the High Speed Shutter or Sports modes picture color may be adversely affected if subject is lit by alternating discharge type light sources such as flourescent or mercury vapor lights MM Zl Dial LCD monitor Mod Dial LCD monitor symbol Viewfinder indication symbol Viewfinder indication CITI Auto Mode Lock Twilight Auto Mode Lock Twilight Locks the camcorder in Full Auto mode preventing Dusk twilight scenery fireworks etc look more incorrect operation due to accidental button natural and dramatic The following happens when pressing during shooting Twilight mode is selected In this mode the following controls are disabled Auto gain control is turned off Fade Wipe Wide Title Display M W B Manual White Balance is set to outdoor mode but White Balance Manual Focus Focus Lock can also be manually changed to another mode Exposure Control and MENU gt pg 29 Auto Focus becomes available only in the range of 10 m to infinity To focus when the subject to camera distance is less than 10 m use manual focusing I pg 23 IRE WIDE Auto Mode Release Auto Mode Release Re enables the controls that were disabled by Auto D D Mode Lock A A Sports sports 1 Sports FG Fu Electronic Fog Filter High shutter speed clearly captures fast moving action Electronic Fog Filter Makes the picture look misty white as when an 1 1000 sec external fo
40. back ONLY NOTE Use the optional Audio and Video cables CONNECT CAMCORDER TO TV As shown in the illustration at left connect the Audio and Video cables between the AUDIO and VIDEO connectors on the camcorder and those on the TV SELECT MODE Set the TV to its VIDEO or AV mode as specified in its instructions Connection To A TV With NO A V Input Connectors Playback ONLY NOTE Use the optional RF V5U RF unit Refer to the RF V5U instruction manual for connection procedure PLAYBACK Using The Cassette Adapter EN 3 Y Cassette Adapter VHS PlayPak Use this to play back a VHS C video cassette recorded with this camcorder It is fully compatible with any VHS video cassette recorder The C P7U adapter is battery powered and automatically performs tape loading and unloading INSERT BATTERY Slide the battery cover up to remove it and install one AA R6 size battery as shown in the VCR illustration at left Then reattach the cover zi INSERT CASSETTE IN ADAPTER Slide the latch to open the adapter compartment door then insert the cassette and close the compartment door PLAY BACK ON CONNECTED VCR Load the cassette adapter into the VCR and play the tape back as you would any other REMOVE CASSETTE FROM ADAPTER Slide the latch and the compartment door opens automatically Then insert your finger in the hole on the underside of the adapter as shown in the illustration at left push up and rem
41. ber plate and safety caution are on the bottom and or the back of the main unit e The rating plate serial number plate of the AC Power Adapter Charger is on its bottom This Class B digital apparatus meets all require ments of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada This camcorder is designed to be used with NTSC type color television signals It cannot be used for playback with a television of a different standard However live recording and viewfinder playback are possible anywhere Use the BN V11U V12U V22U V25U battery packs and to recharge them the provided multi voltage AC Power Adapter Charger An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries ATTENTION The product that you have purchased is powered by a rechargeable battery The battery is recycla ble At the end of its useful life under various state and local laws it may be illegal to dispose of this battery into the municipal waste stream Check with your local solid waste officials for details in your area for recycling options or proper disposal IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful func tions But improper use can result in potential electrical shock or fire hazards
42. d Features cont Picture Stabilizer This feature compensates for unstable images caused by camera shake particularly noticeable at high magnifica tion ACTIVATE PICTURE STABILIZER 1 Press PICTURE STABILIZER QQ appears in the LCD monitor or the viewfinder To switch off the Picture Stabilizer press PICTURE STABILIZER The indicator disappears NOTES Accurate stabilization may not be possible if hand shake is excessive or under the following conditions When shooting subjects with vertical or horizontal stripes When shooting dark or dim subjects When shooting subjects with excessive backlighting When shooting scenes with movement in various directions When shooting scenes with low contrast backgrounds e Switch off Picture Stabilizer when recording with the camcorder on a tripod Exposure Control This feature automatically adjusts the iris for the best available picture quality but you can override and make the adjustment manually SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK BRIGHTEN IMAGE Press maximum 06 The Exposure level indicator appears in the LCD monitor or the viewfinder OR DARKEN IMAGE Press maximum 06 The Exposure level indicator appears in the LCD monitor or the viewfinder When you want to return to the factory setting RESTORE INITIAL SETTING 3 Press and simultaneously The standard setting is i
43. der on again If the error number still appears in the view finder consult your nearest JVC dealer The image is out of focus e The diopter needs to be adjusted I pg 10 The scene being shot is adversely affecting the operation of Auto Focus I pg 22 A character generator title and the e If you remove the power source from the camcorder while date and time displays disappear the power is on all settings and selections are erased Make from the LCD monitor or the sure to turn the camcorder s power off before disconnecting viewfinder the power source The wrong date and time are e f you have not performed Date Time Setting I pg 11 displayed recorded the date and time are not displayed recorded correctly Be sure that Date Time setting is carried out Even though the Lens Cover is open The Lens Cover Warning indicator may blink when the the Lens Cover Warning indicator camcorder is used in dark areas regardless of the position blinks of the Lens Cover The camcorder is a microcomputer controlled device External noise and interference from a TV a radio etc might prevent it from functioning properly In such cases first disconnect its power supply unit battery pack AC Power Adapter Battery Charger etc and clock battery and then re connect it and proceed as usual from the beginning monitor Viewfinder 18min REC SP gt gt gt 4 PAUSE Imin w 1 25 4 Sepia TAPE END gt
44. e camcorder Bright crystal shaped spots appear e Sunlight is directly entering the lens This is not a defect of in the LCD monitor and the the camcorder viewfinder The rear of the LCD monitor is hot e The light used to illuminate the LCD monitor causes it to be hot Close the LCD monitor to turn it off or set the power switch to OFF and let the unit cool down Colored bright spots appear all over e The LCD monitor is made with high precision technology the LCD monitor However black spots or bright spots of light red green or blue may appear constantly on the LCD monitor These spots are not recorded on the tape This is not due to any defect of the unit Effective dots more than 99 99 96 The indicators and the picture color This may occur when the surface or the edge of the LCD on the LCD monitor are not clear monitor is pressed The LCD monitor the viewfinder e Wipe them gently with soft cloth Gently wipe the LCD and the lens have become dirty ex monitor in a semicircle because wiping strongly spreads the fingerprints stain and it won t come out easily The picture is blurred in the Quick This is normal while recording in the EP mode Some noise Review or Retake mode may be present while recording in the SP mode F pg 12 An error number i e E03 appears Turn the camcorder s power off then disconnect the in the LCD monitor or the view power source After a few minutes try turning the power fin
45. e Camcorder CLEAN EXTERIOR 1 Wipe gently with a soft cloth CLEAN LCD MONITOR Slide MONITOR OPEN to open the LCD monitor and wipe gently with soft cloth Be careful not to damage the monitor Close the LCD monitor CLEAN LENS Blow it with a blower brush then wipe gently with lens cleaning paper REMOVE EYEPIECE 4 Turn the eyepiece counterclockwise and pull it out CLEAN VIEWFINDER 5 Remove dust using a blower brush RE ATTACH EYEPIECE Align the marks re attach the eyepiece and turn it clockwise NOTES Avoid using strong cleaning agents such as benzine or alcohol e Cleaning should be done only after the battery pack has been removed or other power units have been disconnected e Mold may form if the lens is left dirty TROUBLESHOOTING ERL Z POWER No power is supplied The power suddenly goes off and doesn t come back on by itself RECORDING Recording cannot be performed Recording does not start The tape is running but there s no playback picture The battery pack has not been attached correctly gt pg 8 e The battery pack is not charged pg 8 The power supply has not been correctly connected gt pg 9 The battery pack has completely discharged e Remove the cassette and disconnect the power source then after a few minutes try turning the power back on If it still doesn t come on consult your nearest JVC dealer e The
46. e chemical reaction while warmer temperatures can prevent complete charging wast store in a cool dry place Extended exposure to high temperatures will increase natural discharge and shorten service life ese avoid prolonged uncharged storage ns remove from charger or powered unit when not in use as some machines use current even when switched off 3 To prevent damage to the camcorder m replace the battery pack when it begins to deliver less recording time per charge NOTE It is normal for the battery pack to be warm after charging or after use Temperature Range Specifications Charging 10 C to 35 C Operation 0 C to 40 C Storage wee 10 C to 30 C NOTES e Recharging time is based on room temperature of 20 e The lower the temperature the longer recharging takes O4 en Cassettes To properly use and store your cassettes be sure to read the following cautions 1 During use make sure the cassette bears the VHS C mark is be aware that recording onto prerecorded tapes automatically erases the previously recorded video and audio signals od make sure the cassette is positioned properly when inserting ed do not load and unload the cassette repeatedly without allowing the tape to run at all This slackens the tape and can result in damage m do not open the front tape cover This exposes the tape to fingerprints and dust 2 Store cassettes D away from he
47. e power on insert a recordable tape and engage the AUX mode refer to VCR s instructions SELECT SCENES ACCESS R A EDIT COUNTER DISPLAY 1 Press PLAY PAUSE then press R A EDIT and the counter display appears in the viewfinder and the screen of the connected TV REGISTER BEGINNING OF SCENE 2 Press REW or FF to locate the beginning of a scene you want then press IN OUT to register that point The data appears under IN on the display REGISTER END OF SCENE 3 Press REW or FF to locate the end of the scene and press IN OUT to register it The data appears under OUT on the display The total time of the registered scene s is displayed at the bottom of the screen REGISTER ADDITIONAL SCENES 4 Repeat steps 2 and 3 for each additional scene as many as 8 MAKE CORRECTIONS 5 Press CANCEL during steps 2 and 3 to erase the most recently registered point NOTES e The RM V700U can be used to operate other camcorder functions as well Point the RM V700U at the camcorder s remote sensor and press any of the following buttons function apears in parentheses ON OFF camcorder R A EDIT IN OUT camcorder IN OUT CANCEL camcorder CANCEL e There must be at least one second between an in point and its corresponding out point ensure correct operation leave at least 15 seconds open between scenes e Blank portions of tape cannot be registered as in points or out points e If it takes more
48. en selected SP EP recording mode button Recording Mode Setting Set depending on your preference SET RECORDING MODE 1 Press SP EP button SP Standard Play provides higher picture and sound quality and is better for dubbing while EP Extended Play is more economical recording at 1 3 the speed of SP Set POWER to CAMERA Tape length indicator T20 T30 T40 NOTE If the recording mode is switched during recording the playback picture will be blurred at the switching point LCD monitor or viewfinder Recording mode indicator SP lt gt EP Me T S Loading Unloading A Cassette OPEN LCD MONITOR Slide MONITOR OPEN and open the LCD monitor to an angle of over 45 degrees OPEN CASSETTE HOLDER Press EJECT until the holder opens Do not use force to open INSERT REMOVE CASSETTE 3 Make sure the label is facing outward CLOSE CASSETTE HOLDER Press PUSH and make sure the holder is closed and locked CLOSE LCD MONITOR First make sure the holder is closed Then close the LCD monitor Turn to take up slack NOTES e Closing the LCD monitor while the cassette holder is still open may cause damage to the LCD monitor A cassette holder can t be opened unless a power supply is attached e Make sure that the tape is not slack when loading the cassette If there is any slack turn the gear on the cassette in the direction of the arrow to take up the slack e Make
49. erent from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help General Battery Precautions When the C P6U or C P7U cassette adapter is not functioning even when correctly operated the battery is exhausted Replace it with fresh one Use only the following batteries C P6U C P7U airis AA R6 size Please make note of the following rules for battery use When misused battery can leak or explode 1 Refer to the C P6U C P7U instructions when replacing the battery 2 Do not expose the battery to excessive heat as it can leak or explode 3 Do not dispose of battery in a fire 4 Remove battery from the unit if it is to be stored for an extended period to avoid battery leakage which can cause malfunctions Battery Packs The supplied battery pack is a nickel cadmium battery Before using the supplied battery pack or an optional battery pack be sure to read the following cautions 1 To avoid hazard dan do not burn PUES do not short circuit the terminals pu do not modify or disassemble 2e use only specified chargers Terminals 2 To prevent damage and prolong service life do not subject to unnecessary shock fea avoid repeated charging without fully discharg ing chara in an environment where temperatures are within the tolerances shown in the chart below This is a chemical reaction type battery cooler temperatures imped
50. ert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance The AA V11U AC Power Adapter Charger should be used with AC 120 60 Hz in the USA and Canada AC 110 240 50 60 Hz in other countries CAUTION applies to the AA V11U TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION s applique l AA V11U POUR VITER LES CHOCS LECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE Warning on lithium battery The battery used in this device may present a fire or chemical burn hazard if mistreated Do not recharge disassemble heat above 100 C 212 F or incinerate Replace the battery with Panasonic Matsushita Electric Sanyo or Maxell CR2025 use of another battery may present a risk of fire or explosion m Dispose of used battery promptly W Keep away from children m Do not disassemble and do not dispose of in fire NOTES e The rating plate serial num
51. ervice 3 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 4 Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition QUICK OPERATION GUIDE SUPPLY POWER BATT RELEASE Using the battery pack El Hook on the battery pack s top end to the camcorder Charging procedure gt pg 8 H Push in the battery pack until it locks into place To remove the battery pack Slide BATT RELEASE and pull out the battery pack PLAYBACK PLAY PAUSE lt Set to PLAY El Set the power switch to PLAY H Press REW The tape will automatically stop at the beginning of the tape El Press PLAY PAUSE Playback starts and the playback picture appears in the viewfinder or the LCD monitor To stop playback press STOP For more details pg 34 The viewfinder switches off automatically to save power when the LCD monitor is opened at an angle of over 45 degrees The LCD monitor turns on off when it is opened closed at approx 45 degrees Or simply play back the tape on a VHS VCR using the Cassette Adapter VHS Playpak gt pg 37 INSER
52. ewfinder PROGRAM AE select dial Date display gt Time display Date Time display Auto Date Record mode Date off mode No indication 4 E The characters you have set using Character Generator Auto Date Record mode Auto Date Auto date record mode Date display DEC 25 97 Time display PM10 50 00 Auto date record executed Date Time display Characters Example of stored characters DEC 25 97 PM10 50 00 Date Time Character Insert This feature allows you to display date time and characters in the LCD monitor or the viewfinder and on a connected color monitor record them manually or automatically and even make your own titles NOTE You should already have performed the Date Time Setting procedure F pg 11 If you haven t do so before continuing DISPLAY SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK SELECT DISPLAY 2 Press SEL repeatedly until gt Disp appears CHOOSE DISPLAY MODE Press SET while in Record Standby to cycle through the modes as shown in the illustration at left NOTES e The selected display can be recorded e f you don t want to record the display select Date off mode before shooting e If you want to delete the display during shooting press SEL repeatedly until Disp appears then press SET e To recall the display press SET again AUTO DATE RECORD Your camcorder automatically
53. g lt pg 39 41 pA AC Power Adapter Cassette Adapter Battery Pack Remote Control Charger AA V11U VHS PlayPak C P7U BN V11U Unit RM V705U Shoulder ED e Lithium Battery 929 Strap CR2025 x 2 VHS EA E Cassettes marked VHS H can be used with this camcorder CONTENTS GETTING STARTED O e i axe Clock Lithium Battery Insertion Removal Viewfinder Adjustment Date Time SeHing iere deerit grt ene RI nro Lomgthy SOHO iue aeo errata eaa Pis Recording Mode Setting Loading Unloading A Cassette Grip Adjustment A ATA Shoulder Strap Tripod Mounting arista rl ltd RECORDING Basic irrito rettet 15 Features dreamed veia tee 18 E Advanced Features ooooooocccccoooocnccooncncncnonononoconanononcnonnnnos 20 E PLAYBACK 34 Basic Playback aia ll D EE 35 amp Basic Connections 36 Using The Ca
54. g filter is attached to the lens Softens the 1 1000 Y 5 1 1000 High Speed Shutter image and gives it a fancy look 1 2000 112000 gt 2 512 12000 se cater High Speed Shutter 1 1000s 1 2000s Captures faster action than Sports mode ND ND ND Effect ND Effect A black mist darkens the picture as when an ND filter is used Helps to counter the effects of glare on the subject 4 The scene being shot is recorded in sepia tinted reddish brown monochrome giving the effect of an older movie Use together with Wide gt pg 26 for the authentic look of a classic Hollywood movie Nn ps g n Ig 5 2 2 RECORDING Advanced Features cont Focusing Auto Focus The camcorder s Full Range AF system offers continuous shooting ability from close up to infinity However correct focus may not be obtainable in the situations listed below in these cases use manual focusing When two subjects overlap in the same scene When illumination is low When the subject has no contrast difference in brightness and darkness such as a flat one color wall or a clear blue sky When a dark object is barely visible in the viewfinder When the scene contains minute patterns or identical patterns that are regularly repeated When the scene is affected by sunbeams or light reflecting off the surface of a body of water When shooting a scene with a high contrast background Foc
55. gainst voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode 2 Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 3 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANSI NFPA 70 ANTENNA L LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT NEC SECTION ELECTRIC SERVICE 810 20 EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE 4 en USE
56. ge vee Pg 9 Random Assemble Editing pg 39 41 Charging the Battery pg 8 Recording Advanced Features pg 20 33 Clock Lithium Battery pg 10 42 Recording tree ener nnne enne e pg 15 Connection to a VCR TV pg 36 Recording Start Stop E e pg 15 Contents e pg Recording Mode Setting e pg 12 Counter Memory Recording Standby res e pg 15 D Remote Control Unit pg 42 Remove Cassette pg 13 Darken the Image pg 24 Retake pg 18 Date Time Character Insert 28 Rewind ME pg 34 Date Time Setting pg 11 S Discharge the Battery pack 8 Diopter Adjust pg 10 Self Timer ERE pg 32 43 Sepia Mode wee pg 21 E Shoulder Strap Attachment pg 14 Electronic Fog Filter Mode pg 21 Shuttle Search pg 35 Erase Protection Specifications pg 55 Exposure Control Sports Mode e pg 21 F Still ore nte pg 35 mass T Fast Forward Tape COLI iaa Focus BOCK eo oe S dn Tape Dubbing Tape Length Setting e pg Time Lapse pg 33
57. guna funci n disponible e Utilice exclusivamente la alimentaci n indicada e No utilice la unidades de alimentaci n suministradas con otro equipo CARGA DE LA BATERIA ALIMENTACION 1 Conecte el cable de alimentaci n de CA del cargador a una toma de corriente Se encender la luz del indicador de alimentaci n COLOCACION DE LA BATERIA 2 Alinee las marcas y deslice la bater a en la direcci n de la flecha hasta que quede bloqueada en su lugar Se enciende la luz indicadora EXTRACCION DE LA BATERIA 3 Cuando la carga est completa se encender el indicador END Deslice la bater a en el sentido opuesto al de la flecha BATERIA CARGA DESCARGA BN V11U aprox 1 h 10m aprox 3h 30m BN V12U aprox 1 h 10m aprox 3 h 30m BN V22U aprox 2h 10m aprox 7h BN V25U aprox 2h 40m aprox 10 h USO DE LA BATERIA COLOCACION DE LA BATERIA Enganche la parte superior del mismo en la videoc mara y emp jela hasta que se bloquee en su lugar EXTRACCION DE LA BATERIA 2 Deslice BATT RELEASE y extraiga la bater a Tiempo de grabaci n aproximado unidad m BATERIA Monitor LCD Monitor LCD activado Visor desactivado Visor desactivado activado BN V11U 50 30 50 35 BN V12U BN V22U 50 30 50 35 105 70 110 75 BN V25U 140 95 150 100 cuando el foco de video est encendido GUIA PARA OPERACION RAPIDA EN O Y Si la unidad comien
58. ion for future reference Model No Serial No Purchase date Name of dealer 0SINXV HD JVC COMPANY OF AMERICA DIVISION OF US JVC CORP 41 Slater Drive Elmwood Park N J 07407 c Printed in Japan 0597TOV K UN YP COPYRIGHTO 1997 VICTOR COMPANY OF JAPAN LTD
59. ither button as many times as necessary for best picture e To reset TRACKING to the original preset press both and buttons simultaneously e Manual Tracking may not work with tapes recorded on other VCRs or camcorders OPERATION NOTES PLAY PAUSE COUNTER R M FEATURE PURPOSE OPERATION Still Playback To pause during playback 1 Press PLAY PAUSE during playback 2 To resume normal playback press PLAY PAUSE again Noise bars appear and pictures may become monochrome during Still Playback This is normal NOTE Shuttle Search To allow high speed search in either direction Forward Search 1 Press FF during playback Reverse Search 1 Press REW during playback Noise bars appear and pictures may become monochrome or darken in Shuttle Search This is normal FEATURE PURPOSE OPERATION NOTE FEATURE Counter Memory Function PURPOSE To make it easier to locate a specific tape segment OPERATION 1 Press COUNTER R M and hold for more than 2 seconds The counter resets to 0 00 00 2 Press COUNTER R M M appears 3 After recording or playback press STOP then REW The tape automatically stops at or close to 0 00 00 4 Press PLAY PAUSE to start playback NOTES e The counter memory functions in the Fast Forward and Rewind modes e To disable Counter Memory Function press COUNTER R M less than 1 second so the M disappears d 6 EN
60. mcorder is aimed at appears on the screen go to the next step BEGIN INSERT EDITING Press START STOP When the counter reaches 0 00 00 editing stops automatically and the camcorder enters the Insert Pause mode END INSERT EDITING 7 Press STOP NOTES When Insert Editing is performed with the LCD monitor fully opened the original audio will be heard from the speaker e After step 5 Retake pg 18 can be performed e The tape may stop slightly before or after the designated end point and noise bars may appear Neither indicates a defect in the unit e Only video signal is recorded in the Insert Editing mode Me 4 LCD monitor or viewfinder RM V700U optional Audio dubbing indicator PS v M 0 05 20 RM V705U provided Audio Dubbing You can record a new soundtrack on a prerecorded tape normal audio only Perform steps 1 2 and 3 of the Insert Editing procedure gt pg 44 before continuing The sound comes from the built in microphone or an external microphone if connected FIND EDIT IN POINT Press REW to go a little beyond the beginning of the scene onto which you want to dub new audio press PLAY to view the recorded tape then press PAUSE at exactly the point where dubbing should start ENGAGE AUDIO DUB STANDBY MODE Press and hold A DUB and without releasing A press and release PAUSE BEGIN AUDIO DUBBING Press
61. me phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place after heating a cold room under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner e Moisture on the head drum can cause severe damage to the video tape and can lead to internal damage to the camcorder itself Serious malfunctioning If malfunctioning occurs stop using the unit immediately and consult your local JVC dealer EN OO GENERAL AUDIO Format VHS NTSC standard Output 8 dBs 1 k ohm Power source DC 6V via AUDIO out Power consumption connector LCD monitor off Speaker 20 mm round x 1 viewfinder on 6 7 W monaural LCD monitor on External viewfinder off 7 1 W microphone input 68 dBs high Light 3W impedance unbalanced Signal system NTSC type with 63 5 mm MONO Video recording system Luminance Color Cassette Tape speed SP EP Recording time max SP EP Operating temperature Operating humidity Storage temperature Weight Dimensions Including viewfinder FM recording Converted sub carrier direct recording Conforms to VHS standard 9 cassette 33 35 mm sec 1 5 16 ips 11 12 mm sec 7 16 ips 40 minutes 120 minutes with TC 40 cassette 0 C to 40 C 32 F to 104 F 35 to 80 20 C to 50 C 4 F to 122 F Approx 1020 g 2 3 Ibs
62. mmediately restored and the Exposure level indicator disappears 2 Ex Black Fader _ C LOURDES _ IN LCD monitor or E FDE OU OUT Function indication viewfinder gt Fade Wipe LA After 2 sec gt Fade Wipe E Bx Black Fader E 1 Mosaic Fader y E Shutter Wipe Off No indication Slide Wipe OFF PROGRAM AE select dial NOTES e Pressing and holding the Recording Start Stop button allows you to record a black blank screen or a mosaic pattern if Mosaic Fader is selected e The screen becomes slightly reddish when the Fade Wipe is used with Sepia pg 21 EN 20 Fade Wipe These effects let you make pro style scene transitions Fade or wipe in works at recording start and fade or wipe out works at recording end or when you enter Record Standby mode SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK SELECT FUNCTION 2 Press SEL repeatedly until Fade Wipe appears ENGAGE FADE OR WIPE STANDBY MODE Press SET to cycle through the modes as shown at left Once the desired mode appears it is selected and reserved The selected mode s name and its indication are displayed in the LCD monitor or the viewfinder for approx 2 seconds Then the name disappears and only the indication remains START RECORDING Press Recording Start Stop to start recording and activate fade or wipe in
63. n 110 75 150 100 Charge marker NOTES en Y CHARGE MARKER A charge marker is provided on the battery pack to help you remember whether it has been charged or not Two colors are provided red and black you choose which one means charged and which means discharged e The recording time per charge is affected by such factors as the time spent in Record Standby mode and the frequency of zooming It is safer to have spare battery packs e Charging times noted on page 8 are for fully discharged battey pack and discharging times are for fully charged battery pack e Charging and discharging times vary according to the ambient temperature and the status of the battery pack e Remember to set the charge marker after charging a battery pack or after detaching a discharged one from your camcorder e Perform the REFRESH function after no less than 5 chargings e High temperatures can damage the battery pack so use only where good ventilation is available Don t allow it to discharge in container such as a bag e If you stop recharging or discharging part way through make sure to remove the battery pack before unplugging the adapter s AC cord Remove the battery pack from the adapter immediately after discharging e To avoid interference with reception do not use the AC Power Adapter Charger near a radio Make sure you unplug the DC cord before charging or discharging the battery pack A blinking CHG
64. ning it off otherwise serious injury may result Do not place the camcorder into the carrying case immediately after using the video light since it remains extremely hot When operating keep a distance of about 30 cm 1 ft between the video light and people or objects Do not use near flammable or explosive materials e lt is recommended that you consult your nearest JVC dealer for replacing the video light 20m 1 second later the mode is activated After 1 sec 4 ESTA LCD monitor or viewfinder PROGRAM AE select dial RECORDING Advanced Features Program AE With Special Effects All you have to do to access any of the variety of shooting effects is to turn the PROGRAM AE select dial SELECT MODE 1 Turn the PROGRAM AE select dial until the symbol of the function you want is aligned with the mark The selected mode s name and its indication are displayed in the LCD monitor or the viewfinder for approx 1 second Then the name disappears and only the indication remains The mode is activated When Auto Mode Lock or Auto Mode Release mode is selected only the mode s name is displayed Then the name disappears and the mode is activated NOTES e Only one effect can be engaged at a time e The screen becomes slightly reddish when the Fade Wipe pg 25 is used in the Sepia mode e The screen becomes slightly dark in the High Speed Shutter mode Use in well lighted situ
65. o move the highlight bar down to Rec Time then press FAR or NEAR to cycle through the choices Stop when the desired time appears Choose from 1 45 1 25 1s 5s or select to turn the function OFF Then press MENU to close Menu screen START TIME LAPSE RECORDING Press the Recording Start Stop button Recording and intervals alternate automatically RELEASE TIME LAPSE MODE To release when the tally lamp is not blinking set Rec Time and Interval Timer in the Menu screen to OFF To release when the tally lamp is blinking press the Recording Start Stop button to stop the blinking then set Interval Timer and Rec Time in the Menu screen to OFF VOLUME Recording mode indicator Tape running indicator gt Playback gt gt Fast Forward Forward Search 4 Rewind Reverse Search Tape counter H Still Playback A Eject LCD Monitor in Retracted Position PLAYBACK Basic Playback LOAD A CASSETTE First slide MONITOR OPEN and open the LCD monitor to an angle of over 45 degrees Press EJECT to open the cassette holder then insert the cassette with the label facing out Press PUSH to ensure the holder is closed and locked SELECT MODE Make sure the LCD monitor is fully open Then set the power switch to PLAY The Power On indicator lights PLAYBACK Press PLAY PAUSE The playback picture appears in the LCD monitor STOP PLAYBACK 4 Press STOP
66. our JVC product you may contact your local JVC Dealer Or from the 48 Continental United States call toll free 1 800 882 2345 cabinet No user serviceable parts inside Refer servicing to qualified service personnel 559 LIMITED WARRANTY CONSUMER VIDEO 1 90 JVC COMPANY OF AMERICA warrants this product and all parts thereof except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below The Warranty Period THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY 50 UNITED STATES THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO WHAT WE WILL DO If this product is found to be defective JVC will repair or replace defective parts at no charge to the original owner Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers Parts used for replacement are warranted only for the remainder of the Warranty Period All products and parts thereof may be brought to a JVC authorized service center on a carry in basis except for Television sets having a screen size 25 inches and above which are covered on an in home basis WHAT YOU MUST DO FOR WARRANTY SERVICE Return your product to a JVC authorized service center with a copy of your bill of sale For your nearest JVC authorized service center please call toll free 800 252 5722 If
67. ove the cassette NOTES e During tape loading and unloading do not touch the reels for safety and tape protection e During special effect playback slow motion still frame etc the picture may vibrate or noise bars may appear on the screen e To record on a VCR using a compact cassette and the adapter cover the adapter s recording safety hole with adhesive tape 388 PLAY PAUSE Dubbing CONNECT EQUIPMENT Following the illustration at left connect the camcorder and the VCR PREPARE FOR DUBBING Set the camcorder s Power switch to PLAY turn on the VCR s power and insert the appropriate cassettes in the camcorder and the VCR SELECT VCR MODE 3 Engage the VCR s AUX and Record Pause modes FIND EDIT IN POINT Engage the camcorder s Play mode to find a spot just before the edit in point Once it s reached press PAUSE on the camcorder START EDITING Press PLAY on the camcorder and engage the VCR s Record mode STOP EDITING TEMPORARILY Engage the VCR s Record Pause mode and press PAUSE on the camcorder EDIT MORE SEGMENTS Repeat steps 4 through 6 for additional editing then stop the VCR and camcorder when finished To AUDIO and VIDEO OUT When connecting connectors the cables open the jack cover Audio and Video cable optional 2 To AUDIO and VIDEO IN connectors VCR Recording deck
68. pe End Display TAPE END CF pg 15 Appears when the end of the tape is reached during playback recording or fast forward e Condensation Warning When this indication appears all functions are disabled Turn the unit off without removing the power source for a few hours and when you turn it on again the indicator should disappear During recording pressing DISPLAY lets you remove indications marked with from the screen INDEX Controls ol Controls Connectors MONITOR OPEN Switch I gt pg 16 J terminal JLIP Joint Level Interface Protocol 2 Button ee CF pg 34 Connector gt RETAKE R Quick Review Button pg 18 Located bengath the j ckcover FF Button Connect the Editing Cable when performing RETAKE PLAY PAUSE Button B STOP Button 6 SEL Button CF pg 25 CD SET Button ES pg 25 Power Zoom Lever CF pg 18 9 DISPLAY Button C pg 15 MENU Button esee CF pg 30 Multi Function Control Exposure Focus FAR NEAR m e Menu Setting Change I gt 30 Tracking eee gt pg 35 2 PUSH Button 8 EJECT Switch 10 Battery RELEASE Switch
69. purple respectively Manual White Balance Adjustment M W B This camcorder s Automatic Color Temperature system senses the color temperature of the ambient lighting for automatic white balance adjustment However precise color adjustment is not possible under the following conditions When an object is in various shades of the same color When a predominantly red or brown object is being shot outdoors In these cases use the camcorder s built in preset filters for white balance adjustment SELECT MODE 1 Turn the PROGRAM AE select dial to any position except AUTO LOCK SELECT FUNCTION Press SEL reapeatedly until M W B appears 2 SELECT WHITE BALANCE Press SET Manual White Balance until the required indication appears in the LCD monitor or the viewfinder MWB With a memorized personal White Balance setting see below eS AN Outdoors on sunny day Me cir ox Outdoors on cloudy day d dm Light source is halogen or tungsten lamp MWB MWB sets the color temperature for the subject s light source so you can shoot with natural colors that are unaffected by surroundings even when there are multiple subjects with different color temperatures SELECT MODE 1 Turn the PROGRAM AE select dial to any position except AUTO LOCK ADJUST FOCUS 2 Point the camcorder at a white flat object such as a sheet of white paper and adjust focus manually pg 23 ADJUST WHITE BALANCE
70. r Indicator gt pg 24 17 Interval Time Recording Time Indicator sees 17 pg 32 12 e Record Standby Mode Indicator 17 pg 15 Lens Cover Warning LENS COVER ran F pg 15 9 Instant Title Display G pg 26 Date Time Character Display C pg 28 Battery Pack Remaining Power Indicator Changes as follows according to the battery pack s remaining power level gt gt 1 77 When the power is almost gone the indicator blinks then the unit shuts off Replace the battery pack with a fully charged one Note The symbol containing 3 darkened squares does not necessarily mean that the battery pack is fully charged Focus Indicator nte CF pg 22 7 Exposure Level Indicator CF pg 24 White Balance Mode Indicator pg 29 Menu Setting Change Indicator pg 30 Index Code Marking r pg 43 Clock Warning Once the power is turned on and the indicator blinks for about 10 seconds perform the date and time settings I pg 11 After setting is complete turn the power off and disconnect the power source If you re connect it and turn the power on and the indicator is blinking that means that the clock lithium battery is either not installed or has discharged Install or replace the old battery with a new one 17 pg 10 2 e Ta
71. records the date for about 5 seconds after recording is initiated in the following situations After changing the date After loading a cassette After Auto Date Record mode is selected by pressing SET In this mode the date is replaced after 5 seconds with Auto Date NOTES e Setting PROGRAM AE to LOCK always engages the Auto Date Record mode and disables all other modes e In the Auto Date Record mode if the date changes while you re shooting the date indication is recorded for about 5 seconds from that point It is not recorded during any other recordings made on that day Me a 29 LCD monitor or viewfinder PROGRAM AE select dial No indication MWB Auto d White balance mode indicator NOTES e To switch to automatic white balance adjustment press SET until the indication disappears or turn the PROGRAM AE select dial to AUTO LOCK e Re adjust the White Balance when the lighting has changed when the camcorder has been turned off and on again or when the PROGRAM AE select dial s position has been changed e When adjusted by putting colored paper in front of the subject in step 2 ADJUST FOCUS this unit makes its color tempera ture standard for automatic white balance So you can enjoy shooting with different colors For example when adjusting with red blue or yellow colors the image becomes the color which aproximates to green orange or
72. ries are not available in some areas Please consult your nearest JVC dealer for details on accessories and their availability Specifications shown are for SP mode unless otherwise indicated E amp O E Design and specifications subject to change without notice 56a Indicador CHG carga Marcas A la toma de corriente de Indicador REFRESH Interruptor REFRESH BATT RELEASE p de carga INDICADOR DE CARGA Se ha suministrado un indicador de carga sobre la bater a para ayudarle a recordar si ha sido cargado o no Los dos colores suministrados rojo y negro le permiten seleccionar la carga y la descarga REFRESCADO El adaptador de CA se caracteriza por la funci n REFRESH que le permite descargar totalmente la bater a antes de recargarla Para descargar las bater as ds coloque la bater a en el adaptador como se muestra en la ilustraci n arriba Luego presione REFRESH El indicador REFRESH se enciende cuando se inicia la descarga y se apaga cuando la descarga ha terminado ATENCION Antes de desmontar la fuente de alimenta ci n aseg rese que la alimentaci n de la c mara de video est desconectada El no hacerlo puede producir una falla de funcionamiento en la videoc mara Alimentaci n Esta videoc mara posee un sistema de alimentaci n de 3 v as que le permite seleccionar la fuente de alimentaci n m s apropiada NOTAS e Sin alimentaci n no hay nin
73. s area built in here is the sensor necessary for shooting e Remote 5 F pg 43 Microphone nnns ots pg 45 Shoulder Strap Eyelets 0 pg 14 Clock Battery Compartment I pg 10 T Battery Pack Mount Electronic Viewfinder A LENS COVER Switch 8 Crip Strap nint cc VIDEO LIGHT OFF AUTO ON Switch pg 19 145 Speaker inerte iet I pg 34 146 Tripod Mounting Socket I pg 14 528 M AC Power Manual FOCUS esee pg 23 Animation Recording he MBR Code pg 39 Audio Dubbing pt N Auto Date Record Auto FOCUS too dada eren dte ND Effect Mde reiteeni pg 21 Auto Mode Lock Mode P Auto Mode Release Mode Picture Stabilizerz ette pg 24 B Playback sees e pg 34 Battery Pack Program AE with Special Effects pg 20 Brighten the Image Provided Accessories pg 6 C Q eR pg 9 Quick Review seee pg 18 Cassette Adapter e pg 37 R Character Generator pg 27 Char
74. service is not available locally box the product carefully preferably in the original carton and ship insured with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center the name and location of which will be given to you by the toll free number If you have any questions concerning your JVC Product please contact our Customer Relations Department WHAT IS NOT COVERED This limited warranty provided by JVC does not cover 1 Products which have been subject to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service or if affixed to any attachment not provided with the products or if the model or serial number has been altered tampered with defaced or removed 2 Initial installation and installation and removal for repair 3 Operational adjustments covered in the Owner s Manual normal maintenance video and audio head cleaning 4 Damage that occurs in shipment due to act of God and cosmetic damage 5 Signal reception problems and failures due to line power surge 6 Video Pick up Tubes CCD Image Sensor Cartridge Stylus Needle are covered for 90 days from the date of purchase 7 Accessories 8 Batteries except that Rechargeable Batteries are covered for 90 days from the date of purchase from the date of
75. ssette 37 EDITING 38 Tape Dubbing ana 38 Random Assemble Editing 39 USING REMOTE CONTROL UNIT 42 CA aa a e 44 Audio DU BBG pa rowan dai URGE SE raa 45 USER MAINTENANCE 46 TROUBLESHOOTING 47 INDEX 49 LCD monitor Viewfinder 49 COBITORS marca ob ocn da Based 50 2 2 5 ecrire 50 50 Offer Plf o M 50 I P 52 CAUTIONS 53 SPECIFICATIONS 55 OPTIONAL ACCESSORIES 55 ESPANOL 56 FOR SERVICING 58 WARRANTY 59 Sa CHG charge indicator POWER indicator END indicator REFRESH switch REFRESH indicator BATT RELEASE ATTENTION Before detaching the power source make sure that the camcorder s power is turned off Failure to do so can result in a camcorder malfunction REFRESH The AC power adapter features a REFRESH function that allows you to fully discharge the battery pack before recharging To discharge the battery sitis attach the battery pack to the adapter as shown in the above illustration Then push REFRESH The REFRESH indicator lights when discharging starts and goes out when discharging is complete Power GET
76. sure the Erase Protection tab is in the position that allows recording If not slide the tab Some cassettes have removable tabs If the tab has been removed cover the hole with adhesive tape e The cassette holder can t be opened while the camcorder is in the record mode 14 GETTING STARTED cont Grip Adjustment EXPAND LOOP 1 Separate the Velcro strip INSERT HAND Pass your right hand through the loop and grasp the grip ADJUST STRAP LENGTH Adjust so your thumb and fingers can easily operate the Recording Start Stop button and Power Zoom lever Refasten the Velcro strip Shoulder Strap Attachment ATTACH STRAP 1 Following the illustration at left thread the strap through the top of the eyelet D then fold it back and thread it through the keeper and then through the buckle 3 Repeat the procedure to attach the other end of the strap to the other eyelet making sure the strap isn t twisted ADJUST LENGTH 2 Adjust as shown in the illustration at left D then slide both keepers snug against the eyelets to prevent slipping 2 Tripod Mounting ALIGN AND TIGHTEN 1 Align the screw and camera direction stud on the tripod with the camera s mounting socket and stud hole Then tighten the screw CAUTION When using a tripod be sure to open and extend its legs fully to stabilize the camcorder To prevent damage to the unit caused by falling over do not use a small sized tripod RECORDING B
77. t Stop button on the camcorder Q INT TIME Button Self Timer Time Lapse F pg 43 O REC TIME Button Animation Time Lapse 17 pg 43 PAUSE Button Pause I pg 35 FF Button D A DUB Button Retake forward IG pg 18 FF FF Shuttle Search F pg 35 Audio dubbing 17 pg 45 B PAUSE IN Connector CF pg 40 D MBR SET Button CF pg 39 viss Button Index Code marking I pg 43 VCR CTL Button CF pg 39 R A EDIT Buttons RM V700U only CF pg 40 Transmitted beam effective area Remote sensor When using the remote control be sure to point it at the remote sensor The above illustration shows the approximate transmitted beam effective area for indoor use The transmitted beam may not be effective or may cause incorrect operation outdoors or when the remote sensor is directly exposed to sunlight or powerful lighting Index Code Marking Interval Timer Indicator Rec Time Indicator LCD monitor or viewfinder RM V700U optional RM V705U provided FEATURE PURPOSE OPERATION NOTE FEATURE PURPOSE OPERATION NOTE n43 Self Timer Animation and Time Lapse The remote control lets you set release Interval Timer and Rec Time functions as well as the Menu screen Self Timer 1 Set Instead of performing steps 1 through 3 on pg 32 Self Timer press INT TIME on the
78. t come on automatically In VCR BRAND BUTTONS i VCR BRAND BUTTONS this case turn the power on manually and try step 2 NAME NAME e If the RM V700U is not able to control the VCR use the controls on the VCR e PHILIPS MAKE CONNECTIONS CONNECT 1 A JVC VCR EQUIPPED WITH REMOTE PAUSE TERMINAL Connect the editing cable to the Remote PAUSE terminal B JVC VCR NOT EQUIPPED WITH REMOTE PAUSE TERMINAL Connect the editing cable to the R A EDIT connector C NON JVC VCR WITH NEITHER Connect the editing cable to the RM V700U s Pause In jack PANASONIC HITACHI JVC A B Cc MAGNAVOX MITSUBISHI NEC PHILIPS All other connections are as shown in the illustration on page 40 TOSHIBA CONTINUED ON NEXT PAGE 000000 0000 0000000000 009000 00000000000009 000000 000009000009000 0000000000990000 000 0 ZENITH 40m Open the cover To AUDIO To J terminal and VIDEO LIP out connectors Editing cable optional 3 5 Audio and mini plug cable Video cable optional To AUDIO ra and VIDEO IN I connectors i To Pause In i VCR Recording deck RM V700U OOOO PREPARE CAMCORDER Insert a recorded tape and set the Power switch to PLAY PREPARE VCR Turn th
79. the power switch is set to CAMERA and the LCD monitor is opened at an angle of 45 degrees or more the LCD monitor switches on and the viewfinder switches off automatically to save power A cassette holder can t be opened unless a power supply is attached There may be a delay after you press EJECT until the holder opens Do not use force The tape s remaining time is displayed in the LCD monitor or the viewfinder as shown The indicated remaining time is approximate The time required to calculate the remaining tape length and the accuracy of the calculation may vary according to the type of tape used The tape remaining time indicator is correct only if the correct tape length has been selected gt pg 12 e END appears when the tape reaches its end and the power goes off automatically if left in this condition for 5 minutes END also appears when a cassette whose tape is already at its end is loaded e While shooting pressing DISPLAY lets you remove some indiations from the screen pg 49 e If the Record Standby mode continues for 5 minutes without performing Zoom or any other operations the camcorder s power shuts off automatically Set the Power switch to POWER OFF and then back to CAMERA to turn the camcorder on again e If the Recording Start Stop button is pressed after the Record Standby mode has continued for over 5 minutes recording may not start immediately e If you re recording on a c
80. u screen START RECORDING Press the Recording Start Stop button after focusing on the subject The recording stops ASSEMBLE SERIES OF PICTURES Repeat step 3 for the desired number of pictures RELEASE ANIMATION MODE 5 Set Rec Time in the Menu screen to OFF NOTES For best results make sure the camcorder is secured when shooting in Animation or Time Lapse mode e Fade Wipe in out cannot be performed during Animation or Time Lapse shooting e Before performing other operations following Animation or Time Lapse recording make sure the Animation or Time Lapse mode is deactivated ACCESS MENU SCREEN SET RECORDING TIME automatically after the selected period of time Time Lapse You can record sequentially at preset time spans Leaving the camcorder aimed at a specific subject you can record subtle changes over an extended period of time NOTE Make sure the camcorder is in the Record Standby mode and the recording mode is set to SP before performing the following steps ACCESS MENU SCREEN Turn the PROGRAM AE select dial to any position except AUTO LOCK then press MENU SET INTERVAL BETWEEN RECORDINGS Press or to move the highlight bar down to Interval Timer then press FAR or NEAR to cycle through the choices Stop when the desired time appears Choose from 155 30s 1min 5min or select to turn the function OFF SET RECORDING TIME Press or t
81. us detection zone The low contrast warning 4 2 appears in the LCD monitor or the viewfinder Focus Lock This feature locks the focus in place which is especially helpful in the following situations When things pass between your subject and the camcorder Engage the focus lock function to lock your PROGRAM AE select dial subject in before recording When you want your subject to be focused and to appear in a corner of the screen First center on the subject and focus using auto focus mode Then engage the focus lock function and move the camcorder until the subject is where you want it SELECT MODE Turn the PROGRAM AE select dial to any position except AUTO LOCK NOTES LOCK FOCUS e If the lens is smeared or blurred accurate Press FAR or NEAR The focus lock indication 4 2 focusing is not possible Keep the lens clean appears in the LCD monitor or the viewfinder wiping with a piece of soft cloth if it gets dirty When condensation occurs wipe with RELEASE FOCUS LOCK a soft cloth or wait for it to dry naturally Press FAR and NEAR simultaneously The focus lock e When shooting a subject close to the lens indication disappears zoom out first 17 pg 18 If zoomed in in the auto focus mode the camcorder could automatically zoom out depending on the distance between the camcorder and the subject When Tele Macro Cx pg 31 is activated the camcorder will not zoom out automatically
82. use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 7 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat SERVICING 1 Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 2 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way f When the product exhibits a distinct change in performance this indicates a need for s
83. ut effect or an instantaneous change in image magnification 36X Hyper zoom Digital circuitry doubles the maximum 18x magnification offered by optical zoom 1 To zoom in slide the Zoom Lever toward T 2 To zoom out slide toward W e During Hyper Zoom the speed increases the further you slide the Zoom Lever Focusing may become unstable during Hyper Zoom In this case set the zoom while in Standby set manual focus or Focus Lock F pg 22 23 then zoom in or out in Record mode e The Zoom Level Indicator I only moves during optical zoom Once the Zoom Level indicator reaches the top of the zoom indicator bar all magnification from that point is through digital processing e During digital image processing the quality of the image may suffer Quick Review To check the end of the last recording 1 Press C and release quickly during the Record Standby mode Tape is rewound for about 2 seconds and played back automatically then pauses in Record Standby mode for the next shot Distortion may occur at start of playback This is normal Retake To re record certain segments 1 Make sure the camcorder is in the Record Standby mode 2 Press either RETAKE button to reach the start point for new recording Pressing forwards the tape and pressing R reverses it 3 Press Recording Start Stop to start recording Noise may appear during Retake This is normal
84. ve the power supply unit OPEN COVER Open the clock battery compartment cover while pressing the release tab REMOVE BATTERY when replacing Insert a pointed non metallic object between the battery and the compartment and pull the battery out INSERT BATTERY Ensuring the plus side is up insert a CR2025 lithium battery and push it in CLOSE COVER 5 Close the compartment cover until it clicks in place NOTE See SAFETY PRECAUTIONS t pg 2 for information on safe handling of lithium batteries Viewfinder Adjustment POSITION VIEWFINDER 1 Adjust the viewfinder manually for best viewability see illustration at left SELECT MODE 2 Set the power switch to CAMERA ADJUST DIOPTER Turn the diopter adjustment control until the indications in the viewfinder are clearly focused Set POWER to CAMERA MM a1 Date Time Setting SELECT MODE First set the power switch to CAMERA Turn the PROGRAM AE select dial to any position except AUTO LOCK ACCESS MENU SCREEN Press MENU SELECT FUNCTION Press to move the highlight bar down to Date Time then press NEAR The Set Date And Time screen appears SET DATE TIME Press FAR or NEAR until the item you want to set begins blinking then press or to until the correct setting appears elf you decide you want to return the date and time to the previous settings press FAR or N
85. xcept AUTO LOCK then press MENU SET INTERVAL TIME Press or to move the highlight bar down to Interval Timer then press FAR or NEAR to cycle through the choices Stop when the desired time appears Choose from 15s 30s 1 min 5min or select to turn the function OFF CLOSE MENU Press MENU START DELAYED RECORDING Press the Recording Start Stop button The tally lamp begins blinking and the blinking frequency increases about 5 seconds before recording is to start Once recording begins the lamp stops blinking but stays lit To Release Self Timer while the tally lamp is blinking press the Recording Start Stop button to stop the blinking then set Interval Timer to OFF 3 Animation Give stationary scenes or objects an illusion of movement This function allows you to shoot a series of pictures each slightly different of the same object for a brief period of time NOTE Make sure the camcorder is in the Record Standby mode and the recording mode is set to SP before performing the following steps Turn the PROGRAM AE select dial to any position except AUTO LOCK then press MENU Press or to move the highlight bar down to Time then press FAR or NEAR to cycle through the choices Stop when the desired time appears Choose from 1 45 1 25 1s 5s or select to turn the function OFF Then press MENU to close Men
86. za a funcionar mal deje de usarla inmediatamente y consulte a su concesionario local de JVC BATT RELEASE Utilizaci n de la bater a El Enganche el extremo superior de la bater a en la videoc mara Procedimiento para carga gt P 8 Empuje la bater a hacia adentro hasta que quede bloqueada en su lugar Para extraer la bater a Deslice BATT RELEASE y extraiga la bater a REPRODUCCION PLAY PAUSE reproducci n pausa Ell Ajuste el interruptor de alimentaci n en PLAY A Presione REW La cinta se detiene autom ticamente al comienzo de la misma El Presione PLAY PAUSE Comienza la reproducci n y la imagen aparece en el visor o en el monitor LCD Presione STOP para detener la grabaci n Por m s detalles gt P 34 El visor se desconecta autom ticamente para ahorrar energ a cuando el monitor LCD es abierto a un ngulo mayor de 45 grados El monitor LCD se activa desactiva cuando se lo abre cierre a 45 grados aprox O simplemente reproduzca la cinta en un VCR de VHS utilizando el adaptador de cassette VHS Playpak 25 P 37 MONITOR OPEN E Deslice MONITOR OPEN para abrir el monitor LCD Abra a un ngulo mayor de 45 grados H Presione EJECT para abrir el portacassette El inserte cassette de video Presione PUSH para cerrar el portacassette Por m s detalles gt P 13 Perilla de abertura cierre LENS COVER Bot n para inicio parada de gr

JVC GR-AXM50 Camcorder User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents