John Lewis JLWM1202 Washer User Manual
Contents
1. Select the Spin programme Select the spin speed by means of the relevant button and then depress the Start Pause button The water is emptied out and the laundry is spun at the selected spin speed Attention Before selecting Drain programme or Spin programme the selector dial must to be positioned on Off 5 Delay start button This button makes it possible to delay the starting of the programme from 30 min 60 min 90 min 2 hours and then by hour up to a maximum of 23 hours The delay you have selected is shown on the display for about 3 seconds afterwards the duration of the programme reappears The Delay start cannot be selected with Soak 30 Drain and Spin programmes Selecting the delayed start You must select this option after you have set the programme and before you press the Start Pause button The machine starts its countdown The programme will start after the selected delay has expired Cancelling the delayed start If you have already pressed the Start Pause button and you wish to cancel the delay time proceed as follows set the washing machine to Pause by pressing the Start Pause button press the Delay start button until the display shows the symbole 0 press the Start Pause button again Important The door will be locked throughout the delay time If you need to open the door you must first set the washing machine to Pause by pressing2. run off a reasonable amount of water to flush out any debris that may have collected in the pipes e Fora correct functioning of the machine the drain hose must be hooked on the proper support piece situated on the top of the back side of the appliance Levelling Level the washing machine by raising or lowering the feet The feet may be tight to adjust as they incorporate a self locking nut but the machine MUST be level and stable check diagonally Any necessary adjustment can be made with a spanner Accurate levelling prevents vibration see note on positioning noise and displacement of the machine during operation Some vibration is inevitable especially if mounted on a wooden floor Sprung wooden floors are particularly susceptible to vibration For advice consult a builder If possible always place the machine on a solid floor In the interest of the environment Washing machines and dishwashers should be connected to the FOUL drainage system the water will then be taken to a sewage works for treatment before being discharged safely into a river SHOWER SINK TOILET BIDET WASHING MACHINE DISHWASHER RAINWATER RUN OFF FOUL DRAIN SURFACE WATER DRAINS amp SEWERS FOUL SEWERS H SEWAGE 1 UNTREATED TREATMENT i DISCHARGE WORKS Y TREATED DISCHARGE RIVER It is essential that these appliances are not connected to the
3. E Cold a Cold EI D t m 40 if IL Economy 40 E Delicates 30 H Delicates 40 30 M JLWMI202 Cold Detergent dispenser drawer 2 Programme selector dial The programme selector dial is divided into the following sections Cottons Synthetics Delicates Wool Hand washing Special programmes from Soak 30 to 30 Minute wash Reset Off programme Off The selector dial can be turned either clockwise or anticlockwise Economy position corresponds to an ENERGY SAVING programme and Cold to a cold wash Before setting the dial to any position ensure that the machine is turned to the Off position Important At the end of the programme the selector dial must be turned to position Off 4 5 678 3 Spin button Press this button repeatedly to change the spin speed or to select position None no spin if you want your laundry to be spun at a speed different from the one proposed by the washing machine The relevant light will light up Spin speed The following speeds are available for the different fabrics Cottons linen 500 700 900 max 1200 r p m for the model J WM 1202 and 1400 r p m for the model J WM 1403 Synthetics and wool 500 700 max 900 r p m Delicates and 30 Minute wash 500 max 700 r p m Position None By selecting the option None all the spinning phases are cancelled If you
4. Stain 3 Kg 0 5 Synthetics fabrics Extra rinse Quiet Del 40 30 da Ls viscose Spin reduction None 3 Dus elicates z polyester items Prewash Extra rinse Kg t Delicates curtains Quiet Garments bearing the Am 40 Pure new wool Spin reduction Wool 30 Cold non shrink machine None 2kg 0 35 55 55 Oo Wool washable or Hand Quiet wash label The Economy Cottons 60 is the reference programme for the data entered in the energy label in compliance with EEC 92 75 standards This data is given purely as an indication the consumption values may vary in relation to the quantity and type of laundry the temperature of the water supply and the ambient temperature The data refers to the highest temperature provided for each programme Only at a temperature of 40 C or higher 21 Consumptions Priori Programme Available Load g description options Energy Water Time kWh litres h min Soak for 30 minutes Soak 30 at 30 C 6 Kg 0 23 I9 28 Sra Spin dieu Rinse m at max Erra iine 6 Kg 0 06 59 45 Spes Quiet rinse with liquid 2 iti pin reduction Softeners additive None 2 Long spin at max Quiet speed Drain For emptying out the last rinse of the programmes Water draining 2 with option Quiet and programme Soak 30 Spin ae spar Spin reduction 6 Kg 10 30 Minute wash Wash at 30 C Spin reduction Short cycle for lightly 2 rinses None 2 Kg 0 3 40 30 s
5. does not start The door has not been closed E40 The plug is not properly inserted in the power socket There is no supply at the socket The main fuse or the fuse in the plug has blown The Start Pause button has not been depressed The Delay start option has been selected The machine does not fill The water tap is closed EID The filter in the inlet hose is blocked EIO The inlet hose may be squashed or kinked EU The door has not been closed EU The machine fills then empties The end of the drain hose is too low immediately The end of the drain hose is submerged in water There is no vent in the end of the drain hose The machine does not empty The drain hose may be squashed or kinked E20 and or does not spin The Quiet option has been selected The drain pump may be blocked E20 The None option has been selected The drainage system pipes are blocked The programme Soak 30 which ends with water left in the tub has been selected There is water on the floor Too much detergent or unsuitable detergent has been used creates too much foam Check whether there are any leaks from the inlet hose fittings It is not always easy to see this as the water runs down the hose check to see if it is damp The drain hose may be damaged or not securely positioned The cap on the emergency emptying hose has not been replaced after cleaning the filter Unsatisfactory washing results Too little deterg
6. of the following methods Into a drainage standpipe Firstly form a hook in the end of the drain hose using the U piece supplied U piece supplied Place the drain hose into your standpipe which should have an internal diameter of approximately 38mm thus ensuring there is an air break between the drain hose and standpipe 38 mm 11 27 standpipe diameter 30 em 12 When discharging into a standpipe ensure that the top of the standpipe is no more than 90cm 35 4 and no less than 60cm 23 6 above floor level The drain hose may be extended to a maximum of 4 metres An additional drain hose and joining piece is available from your local Service Force Centre The joining piece must have an internal diameter of 18mm If your drain hose looks like this see below you do not require the U piece Just push the hose firmly into the standpipe 2 Onto a sink outlet spigot If the outlet spigot has not been used before remove any blanking plug that may be in place Push the drain hose onto the spigot and secure with a clip if required ensure a loop is formed in the drain hose see diagram to prevent waste from the sink entering the washing machine Important Before connecting the machine to new pipework or to pipework that has not been used for some time
7. surface water drainage system as this water is discharged directly into a river or stream and may cause pollution If you require any further advice please contact your local water authority Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person WARNING THIS APPLIANCE MUST BE N EARTHED The manufacturer declines any liability should this safety measure not be observed Should the appliance power supply cableneed to be replaced this must be carriedout by a Service Force agent see page 19 Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance s rating plate The rating plate is located at the top of the rim of the open door Mod Prod No Ser No The appliance is supplied with a 3amp plug fitted In the event of having to change the fuse in the plug supplied a 13amp ASTA approved BS1363 A fuse must be used Should the plug need to be replaced for any reason proceed as described below The wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live GREEN amp YELLOW 8 BROWN CORD CLAMP If you fit your own plug the colours of the wires in themains lead of your appliance may not correspond with thema
8. JLWVM 1202 200 spin washing machine JLWM 1403 400 spin washing machine John Lewis N Important Safety Information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings have been provided in the interest of safety You MUST read them carefully before use or installation by a qualified person If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance Installation This appliance is heavy Care should be taken when moving it Itis dangerous to alter the specifications or attempt to modify this product in any way All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in instructions Care must be taken to ensure that the appliance does not stand on the electrical supply cable Ifthe machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely Child Safety This appliance is designed to be operated by adults Ch
9. Press the Start Pause button The relevant light will stop flashing and only the light relevant to the phase that is in progress will remain lit If you have chosen a delayed start the washing machine will begin the countdown The display will show the duration of the programme or the selected delay Il How to change an option or a programme during its cycle It is possible to change any option before the programme carries it out Before you make any change you must pause the washing machine by pressing the Start Pause button Changing a running programme is possible only by resetting it Turn the programme selector dial to Off and then to the new programme position The washing water in the tub will not emptied out Start the new programme by depressing the Start Pause button 12 How to interrupt a programme Depress the Start Pause button to interrupt a programme which is running the corresponding light starts to flash Depress the button again to restart the programme 13 How to open the door during the cycle of a programme You can open the door after having set the washing machine to Pause provided the following conditions exist the washing machine is not in the heating phase beyond 55 C the level of the water is not high If these requirements are met when you pause the washing machine the door locked light goes off and the door can be opened Should it not be possible to
10. Quiet option or Soak 30 programme Turn first the programme selector dial to Off then select the Drain programme and depress the Start Pause button Spin Separate long spin at the max speed for hand washed garments The spin speed will automatically assume the setting for cotton items You can reduce the speed by means of Spin button to adapt it to the fabrics to be spun 30 Minute wash This is a complete programme that can be combined with the following options Spin speed reduction Quiet and Delay start To be used for laundry which is lightly soiled or which needs freshening up Max load 2 kg Washing temperature 30 C Programme duration 30 minutes Final spin speed 700 rpm Off Reset Switching the machine off To reset a programme turn the selector dial to Off Now can a new programme be selected i Using the washing machine Before the first wash we recommend that you pour 2 litres of water into the main wash compartment UIJ of the detergent drawer in order to activate the ECO valve Then run a cotton cycle at 95 C without any laundry in the machine to remove any manufacturing residue from the drum and tub Pour 1 2 a measure of detergent into the dispenser drawer and start the machine WASHING 5 KG OF WHITE COTTON AT 90 C Suppose you have 5 kg of laundry to wash It is white cotton and is suitable for high temperature washing Load the laundry Open the door Place the la
11. Voltage Directive and subsequent modifications 89 336 EEC of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 23 24 23 23 23 23 23 23 23 24 24 24 24 25 26 26 Description of the Appliance Detergent dispenser drawer 2 Control panel 3 Door locked light 4 Door opening handle 5 Drain pump 6 Adjustable feet Door locked light It stays on during the whole programme indicating that the door is locked When the light goes out the door can be opened Detergent dispenser drawer LI Prewash LII Main wash Fabric softener Child safety feature This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine To activate this device rotate the button without pressing it inside the door clockwise until the groove is horizontal If necessary use a coin To disable this device and restore the possibility of closing the door rotate the button anti clockwise until the groove is vertical Installation It is dangerous to alter the specifications or attempt to modify this product in any way Care must be taken to ensure that the appliance A does not stand on the electrical supply cable Any electrical work required to install this A appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this A applia
12. air the washing machine i Hints amp Tips on Washing Do NOT overload the machine Weigh the laundry the first few times you use the appliance The average weights of the most common items are listed below as a guide 1000g I kg Sheet 700 1000 g Pillow case 100 200 g Tablecloth 400 500 g Serviette 50 100 g Tea towel 70 120 g Linen hand towel 100 150 g Towelling hand towel 150 250 g Towelling bath towel 700 1000 g Bath robe 1000 1500 g Man s shirt 200 300 g Apron 150 200 g Load the laundry loosely alternating large items with small ones Sort the laundry according to the type of fabric colour fastness and how dirty it is Avoid washing unhemmed or torn items as they may unravel Before washing empty all pockets of small objects which may have been left inside coins keys screws etc as these could damage the drain pump When washing curtains remove the hooks Close poppers and zips and fasten loose buttons tis essential to wash new coloured items separately when washing for the first time When washing fabrics requiring different wash temperatures together always select the lowest temperature White items should not be washed with coloured items Very small items handkerchiefs ribbons socks etc should be washed in a washing bag or a pillow case Use a good quality detergent suitable for automatic washing machines Use th
13. and additive dispenser drawer should be cleaned regularly Remove the drawer by pressing the catch downwards and by pulling it out Flush it out under a tap to remove any traces of accumulated powder To aid cleaning the top part of the additive compartment should be removed 23 Cleaning the drawer recess Having removed the drawer use a small brush to clean the recess ensuring that all washing powder residue is removed from the upper and lower part of the recess Replace the drawer and run the rinse programme without any clothes in the drum Cleaning the pump The pump should be inspected if the machine does not empty and or spin the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump Proceed as follows Disconnect the appliance f necessary wait until the water has cooled down Open the pump door Place a container close to the pump to collect any spillage Pull out the emergency emptying hose place it in the container and remove its cap When no more water comes out unscrew the pump cover and remove it Always keep a rag nearby to dry up spillage of water when removing the cover Remove any objects from the pump impeller by rotating it Put the cap back on the emergency emptying hose and place the latter back in its seat Screw the pump cover fully in Close the pump door AN Warning When the appl
14. be connected to a suitable existing tap with the drain hose discharging into a sink The appliance has an inlet hose with female 3 4 BSP thread connector If this connection is not compatible with the plumbing of the existing installation a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing Any alteration to your existing plumbing must be carried out by a competent person or qualified plumber Water inlet Connect the hose to a tap with a 3 4 thread Always use the hose supplied with the appliance to connect to the water supply Do not use previously used hoses for water connection Installation should comply with local water authority and building regulations requirements The appliance must be connected to a cold water supply A minimum water pressure of 50 kPa 0 5 bar is required for safe operation of the appliance If you cannot make the cold water connection direct from the rising mains you may be able to operate the appliance from your cold water storage system There should be a minimum distance of 5 02m 16 5 ft between the appliance inlet and the bottom of the water storage tank Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks Water drainage This appliance is designed to be permanently plumbed into your home s drainage system using one
15. e correct quantities of detergent For wool use gentle detergent only in small quantities Bleach is very corrosive it should be used with care and kept out of reach of children Some stains such as fruit wine grass rust etc are difficult to remove and should be treated before washing with specific products which can be found in most household shops In some cases it may help to soak the stain before washing with a special pre soak product or biological detergent If you have used the machine to wash rinse or spin only non colour fast garments there may be dye left in the sump To ensure any subsequent wash is not contaminated with the dye select and carry out a rinse and spin programme without any garments to ensure that any dye is removed from the sump Once you have finished using the machine you are advised to unplug it and turn off the water tap Wash Care Symbols Wash care labels inside garments recommend how to launder your clothes with the best results The care labelling code is in line with care labelling used in the rest of Europe The symbols used make it easy to select the correct programme on your washing machine WASHING SYMBOL WASH ACTION FABRIC Normal Maximum White Cotton or Linen without Special Finishes Normal Maximum amp g Cotton Linen or Viscose without Special Finishes Colourfast at 60 C Reduced Medium Nylon Polyester Cotton Viscose with Special Finish
16. eavy soiled laundry a stain phase at the temperature of 40 C pour a stain removing detergent into the compartment marked UJ This function is available in cotton and synthetic programmes with a temperature of 40 or higher The washing time will be prolonged by few minutes The Prewash and the Stain options cannot be selected together oe Extra rinse this option can be selected with all programmes except the wool programmes and 30 Minute wash The machine will add 2 rinses to the selected programme This option is recommended for people who are allergic to detergents and areas where the water is very soft Quiet when you choose this option the machine will not drain the water of the last rinse this will ensure the minimum of creasing to laundry As all spinning phases are cancelled this washing cycle is very quiet and it can be useful at night or in hours with more economical power rate The machine will perform 3 additional rinses on cottons and additional rinse on synthetics programmes At the end of the cycle the light corresponding to the option Quiet and the Rinse hold pilot phase light are on the Start Pause button light goes out the door locked light is on and the door cannot be opened to indicate that the water must be drained A blinking zero will appear on the display To empty out water there are 2 possibilities Select Drain programme the water is emptied out without spinning
17. ent or unsuitable detergent has been used An insufficient amount of detergent leaves the laundry looking grey and causes lime scale to form Stubborn stains have not been treated prior to washing The correct wash programme temperature has not been selected Too much laundry has been placed in the drum 25 The machine vibrates when The internal packing has not been removed spinning The machine is in contact with the wall or furniture The machine is not level and stable check diagonally The washing load is badly distributed in the drum Maybe there is very little laundry in the drum The door will not open The water level is above the bottom edge of the door The machine is heating the water The drum is turning In any case the door can be opened only when the door locked light has gone out Spinning starts late or the The electronic balance control device has cut in because the laundry is machine does not spin not evenly distributed in the drum The laundry is redistributed by reverse rotation of the drum This may happen several times before the unbalance disappears and normal spinning can resume If after few minutes the laundry is still not evenly distributed in the drum the machine will not spin In this case redistribute the load manually and select the spin programme The machine makes an unusual The machine is fitted with a type of motor which makes an unusual noise noise compared with other traditional motors This
18. ergent remains unused at next washing Emergency emptying out If the water is not discharged proceed as follows to empty out the machine pull out the plug from the power socket close the water tap if necessary wait until the water has cooled down open the pump door place a bowl on the floor and place the end of the emergency emptying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bowl is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out clean the pump if necessary as previously described replace the emergency emptying hose in its seat after having plugged it screw the pump cover again and close the door Something Not Working Please carry out the following checks before contacting your local Service Force agent IMPORTANT if you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a charge will be made even if the appliance is under guarantee During machine operation it is possible that the End light flashes and one of the following alarm codes appears on the display EIQ problem with the water supply E20 problem with water draining EdU door open Once the problem has been eliminated press the Start Pause button to restart the programme If after all checls the problem persists contact your local Service Force Centre The machine
19. es Cotton Acrylic Mix Normal Maximum Cotton Linen or Viscose Colourfast at 40 C but not 60 C Reduced Medium Acrylics Acetate Triacetate Wool mixes Polyester wool blends Much Reduced Minimum Wool wool mixtures Silks Hand wash only Gg gg E Do not machine wash BLEACHING A Chlorine bleach may be used IRONING fal Hot iron Cotton Linen Viscose cel Warm iron Polyester mixtures Wool el Cool iron Acrylic Nylon Polyester DRY CLEANING May be dry cleaned Other letters and or a bar beneath the circle will indicate the required process to the dry cleaner TUMBLE DRYING with high heat setting I with low heat setting ww May be tumble dried X A cross through any symbol means DO NOT Important Notes fabric conditioner to avoid the conditioner entering the machine prematurely For best results always use the dispenser drawer for dispensing detergents and liquid additives Once the dispenser has been filled close it by pushing it in gently This is particularly important if you are using 20 When using liquid detergent and a prewash programme place the detergent into the correct compartment in the dispenser drawer after the prewash has finished Washing programmes Consumptions Fabrics Programmer Type of laund Avalone Load E temperature YP y options WE
20. ial to another programme when the machine is working all the lights of the programme progress display will flash for about 2 seconds but the washing machine will not perform the new selected programme Programme information Soak 30 This is a special programme for heavily soiled laundry The machine performs a soak of about 30 minutes at 30 C At the end of the soak time the machine will stop automatically with water left in the tub The display will show a flashing zero Pour the detergent for the soak programme into the compartment marked Before starting a new washing phase it is necessary to empty the water by selecting the Drain programme This function cannot be used with Wool programmes Rinse With this programme it is possible to rinse and spin the garments which have been washed by hand The machine performs 3 rinses followed by a final long spin at the maximum speed Important The spin speed will automatically assume the setting for cotton items If required reduce the speed to the desired level by depressing the Spin button Softeners Hand washed garments can be be starched or softened with this programme The machine performs rinse followed by a final long spin at the maximum speed which can be reduced by depressing the Spin button The final spin is foreseen only for cotton items as in the spin programme Drain For emptying out the water of the last rinse in programmes with the
21. iance is in use and depending on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When replacing the cover ensure it is securely retightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filter If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time Turn off the water tap Unscrew the water inlet hose Clean the filter using a hard bristle brush Tighten up the inlet hose The dangers of freezing If the machine is exposed to temperatures below 0 C certain precautions should be taken Turn off the water tap Unscrew the inlet hose Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again When you intend to start the machine up again make sure that the room temperature is above 0 C Important Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash compartment of the detergent drawer and then run the drain programme This will activate the ECO valve avoiding that part of the det
22. ildren should not be allowed to tamper with the controls or play with the product Pets and children have been known to climb into washing machines Please check your drum before use The glass door becomes very hot during the washing cycle Keep children away from the vicinity of the appliance whilst it is in operation Keep all packaging well away from children Keep all detergents in a safe place out of children s reach When the appliance is to be scrapped cut off the power supply cable and destroy the plug with the remaining cable Disable the door catch in order toprevent children from becoming trapped inside while playing Use Always unplug the appliance and turn off the water supply after use Do not overload the appliance See relevant section in the instruction book Only wash fabrics which are designed to be machine washed If in doubt consult the care label on the clothes Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine Garments which have been in contact with volatile petroleum products should not be machine washed If vola
23. ing to the water hardness the degree of soiling and the quantity of laundry being washed v Environmental Information After unpacking please dispose of packaging with due regard to safety and the environment N Materials marked with the symbol C are recyclable Check with your local Council or Environmental Health Office to see if there are facilities in your area for re cycling this appliance WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely The symbol K on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Contents For the User Important Safety Information Installation Child safety feature Description of the Appliance Door locked light Detergent dispenser drawer The Control Panel Programme information Using the washing machi
24. inse O Rinse hold O Drain O Spin O Filter O End If your laundry needs a soak time turn the programme selector dial to Soak 30 and then before starting a washing cycle drain the water as described in the Soak 30 paragraph 6 Select the spin speed or the None option Press the Spin button repeatedly button if order to select the desired spin speed or the None no spin option The relevant light will light up JLWM 1202 JLWM 1403 7 Select the desired options If your laundry is very dirty it may be advisable to select the Prewash option or the Intensive option If your laundry has heavy stains and it is necessary to prolong the washing time select the Stain option The special detergent for stains Stain remover is loaded from the compartment marked LU If you wish the laundry to undergo an extra rinse select the Extra Rinse option If your laundry should not be creased select the Quiet option to leave the fabrics in the water of the last rinse The relevant light illuminates oO O O 9 Select the Delay start Before you start the programme if you wish the start to be delayed press the Delay Start button repeatedly or keep it pressed to select the desired delay The selected delay time value up to 23 hours will appear on the display for 3 seconds then the duration of the programme will appear again Delay start Q 10 Start the programme
25. jak itres 90 Sheets household Spin reduction None White linen towels Prewash Intensive 6 Kg 2 57 cotton Cottons tablecloths Stain Extra rinse Quiet 90 f Cottons Sheets household Spi duction N Mud linen towels PPrewash Stan 6 Kg 2 3 INTENSIVE tablecloths Extra rinse Quiet option selected Econom White 60 Sheets household spin reduction None cotton linen towels Prewash Stain 6 Kg 1 02 Cottons tablecloths Extra rinse Quiet Fast coloured and White and 60 40 non fast items for Spin reduction None coloured 30 Cold example hand towels ako eal 6 Kg 1 2 cotton Cottons sheets underwear di eer tablecloths shirts Quiet 60 40 Fast coloured items White and 30 Cold hand towels Spin reduction None coloured Cottons Prewash Stain 6 Kg I3 sheets underwear ay i cotton INTENSIVE Extra rinse Quiet option selected tablecloths shirts Coloured Economy Coloured items for Spin reduction None OON 40 example underwear Sti dris 6 Kg 1 14 Cottons shirts blouses T Quiet pe A pos Shirts blouses Spin eo abe i j Co i rewash Intensive 3 Synthetics Ee mixed Stain Extra rinse Kg Synthetics abrics Quiet 60 40 o 30 Cold Shirts blouses Spin reduction None Synthetics Synthetics underwear mixed Prewash Stain 3 Kg 0 95 INTENSIVE fabrics Extra rinse Quiet option selected Economy Shirts blouses Spin reduction None Synthetics 40 underwear mixed P Prawa
26. nce should be carried out by a qualified plumber or competent person Technical Specifications DIMENSIONS Height 85 cm Width 60 cm Depth 6 cm POWER SUPPLY VOLTAGE 230 240 V 50 Hz TOTAL POWER ABSORBED 2050 W 10A WATER PRESSURE Minimum 0 05 MPa 0 5 bar Maximum 0 8 MPa 8 bar ITEMS WITH PROGRAMME COTTONS ECONOMY 60 MAXIMUM RECOMMENDED LOAD Cotton linen 6 kg Synthetics 3 kg Delicate fabrics 3 kg Wool Hand wash 30 Minute wash 2 kg SPIN SPEED Maximum 1200 rpm JEWM 1202 1400 rpm LWM 1403 CONSUMPTION DATA FOR WASHING Energy 1 02 kWh 6 KG NORMALLY SOILED COTTON Water 49 litres Unpacking A All transit bolts and packing must be removed before using the appliance Keep all packaging away from children You are advised to keep all the transit bolts for re use in case the machine is to be transported again Using a spanner unscrew and remove the two rear bottom screws Slide out the two plastic pins Lay the machine gently on its back making sure that the hoses are not squashed Remove the polystyrene block from the bottom of the machine and release the two plastic bags Very carefully slide out the left polythene bag removing it towards the right and then downwards Repeat the operation for the right polythene bag removing it towards the left and then upwards Remove the polystyrene base Set the machine upright and unscrew the remaining rear scre
27. ne Load the laundry Measure out the detergent Measure out the fabric softener Switch the machine on Select the desired programme temperature Select the spin speed or the None option Select the desired options Select the Delay start Start the programme How to change an option or a programme during its cycle How to interrupt a programme How to open the door during the cycle of a programme End of programme Hints amp Tips on Washing Wash Care Symbols Washing Programmes Ou Vpn UJ 11 14 I5 16 18 l6 l6 l6 l6 l6 17 17 17 17 17 18 18 18 19 20 21 22 For the Installer Installation Technical Specifications Unpacking Positioning Installation on a suspended floor Plumbing in Water inlet Water drainage Levelling In the interest of the environment Electrical connection Permanent connection Maintenance and Cleaning Descaling After each wash Maintenance Wash External cleaning Cleaning the dispenser drawer Cleaning the drawer recess Cleaning the pump Cleaning the water inlet filter The dangers of freezing Emergency emptying out Something Not Working Repairs After Sales Service Guide to use the Instruction Manual The following symbols will be found in the text to guide you throughout the instructions AN Safety instructions i Hints and tips V Environmental information C C This appliance complies with the following E E C Directives 73 23 EEC of 19 2 73 Low
28. new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine No water is visible in the drum Machines based on modern technology operate very economically using very little water without affecting performance Repairs After Sales Service So that you always have these numbers to hand we In the event of your appliance requiring service or if recommend you to make a note of them here you wish to purchase spare parts please contact our extended warranty administrators by telephoning 0870 01 07887 They will give you details for your local Service Force Centre Service Force are the appointed national appliance repair agents responsible for warranty repairs to this appliance Before calling out an engineer please ensure you have read the details under the heading Something Not Working Mod Prod No Ser No When you contact the Service Force Centre you will need to give the following details P0042 BD Your name address and post code Your washing machine is covered by a 3 year 2 Your telephone number parts and labour guarantee see separate details given at point of sale Please retain your 3 Clear and concise details of fault purchase receipt safely for the service 4 The purchase date and found on your receipt A a Please note that a valid purchase receipt is 5 The model and se
29. oiled fabrics Short spin Quiet For cancelling the programme which is g g Off Reset running or to switch g the machine off You can reduce the spin speed by means of the relevant button to adapt it to the fabrics to be spun 22 Maintenance and Cleaning You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and according to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits After each wash Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the door open after a wash will also help to preserve the door seal Maintenance wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash The drum should be empty of laundry Select the hottest cotton wash programme Use a normal measure of detergent must be a powder such as Ariel Futur External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thoroughly Cleaning the dispenser drawer The washing powder
30. open the door and should it be absolutely necessary to do so switch the machine off by turning the selector dial to Off After approximately 3 minutes you can open the door Pay attention to the level and temperature of the water in the washing machine When you close the door to restart the programme turn the dial to the previous programme repeating the options previously selected and press START PAUSE button 14 End of programme At the end of the programme the washing machine stops automatically the End light illuminates the Start Pause button light goes off and the display shows a flashing zero If you had selected the Quiet option the door locked light is on the door is locked the Rinse Hold pilot light and the Quiet option light remain lit to indicate that the water must be drained The display shows a flashing zero To drain or to spin see paragraph Quiet on page 12 Turn the programme selector dial to Reset Off to switch the machine off Remove the laundry from the washing machine Check whether the drum is completely empty by rotating it with your hand The purpose of this is to prevent any items of laundry from remaining accidentally in the drum where they might get damaged in a subsequent wash e g by shrinking or bleed colour into another load of laundry We advise you to close the water supply tap and disconnect the plug from the socket Leave the door ajar in order to
31. rial number of the appliance required for in guarantee service calls found on the rating plate see picture 26 John Lewis Partnership 171 Victoria Street London SWIE 5NN www johnlewis com 03 06 132 982 380
32. rkings identifying the terminals in your plug Proceed as follows I The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow 2 The wire coloured blue must be connected to the terminal marked IN or coloured black 3 The wire coloured brown must be connected to the terminal marked L or coloured red 4 Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely The power supply cable must be easily accessible after installing the appliance Permanent connection In the case of permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply mains with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations The switch must not break the yellow and green earth cable at any point The Control Panel Wash time 1200 John Lewis o 30 Minute wash Of 90 By O9 Spin s Economy 60 El 700 p SM 9 rain n 60 W Oso O Rinse hold Softeners a Economy 40 ONone O O Oo O O Rinse 40 Extra ET Spin Prewash Intensive Stain rinse Quiet oal 2
33. select this option with programmes for cotton and synthetics the machine will perform some extra rinses 4 Option buttons Depending on the programme different functions can be combined These must be selected after choosing the desired programme and before depressing the Start Pause button When these buttons are pressed the corresponding pilot lights illuminate When they are pressed again the pilot lights go out If an incorrect option is selected the pilot lights flash for about 2 seconds and the message Err is displayed Press these buttons to select the following options Prewash select this option if you wish your laundry to be prewashed before the main wash not available for Wool and 30 Minute wash The prewash ends with a short spin at 650 rpm in programmes for cotton and synthetic fabrics whereas in the programme for delicate fabrics the water is only drained This option can be selected for heavily soiled laundry but not together with Stain option Intensive this option can be selected for heavily soiled cottons and synthetic If you depress this button the washing intensity will be increased and the washing time will be prolonged by few minutes depending on the selected temperature and type of fabric This option is not available for Economy programmes Wool Delicates and 30 Minute wash programmes Stain select this button if you wish to add to the washing of h
34. the Start Pause button After you have closed the door press the Start Pause button again 6 Start Pause button This button has two functions Start after you have selected the desired programme and options press this button to start the washing machine The light above the button will stop flashing and remain lit If you have selected a delay time the countdown will begin and will be shown on the display Pause when you press this button again the programme in progress is interrupted The light above the button will start flashing To restart the programme from the point at which it was interrupted press the button again When you PAUSE the cycle and it becomes possible to open the door provided the washing machine is not in the heating phase the level of the water is not high If all these requirements are met the door locked light goes off Important You must set the washing machine to Pause before you make any change in the programme in progress 7 Display The following pieces of information are shown on the display Duration of washing programme in hours and minutes after you have selected a programme 2 05 While the programme is running after you have pressed the Start Pause button the displayed time value decreases by one unit every minute The washing machine has completed the programme this is indicated by a flashing zero The washing machine has stopped with water in the
35. tile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum Only use the advised quantities of fabric softener Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities As some duvets and eiderdowns should be washed in large commercial machines because of their bulk please check with the manufacturer of the item before washing in a domestic machine Maintenance and Cleaning For information on maintenance and cleaning your washing machine see pages 23 24 of this instruction manual Service This product should only be repaired or serviced by anauthorised Service Engineer and only genuine approvedspare parts should be used 7 Ecological hints To save water and energy and help protect the environment we recommend that you follow these hints Normally soiled laundry may be washed without prewashing in order to save detergent water and time the environment is protected too The machine works more economically if it is fully loaded With adequate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature Measure out detergent accord
36. tub at the end of the Soak 30 or a programme with the Quiet option this is indicated by a flashing zero Delay start a time value indicated in hours and selected by means of the relevant button The delay time is displayed for 3 seconds then the duration of the selected programme reappears After you have pressed the Start Pause button the countdown is updated every hour and for the last two hours every 30 minutes An incorrect option selection has been made this is indicated by the message Err when a function incompatible with the current programme is selected Err An alarm code indicates a fault in the machine operation see the relevant chapter 8 Programme phase indicator lights When you select a programme the lights relevant to the phases that form the programme light up After you have started the programme only the light relevant to the phase that is currently being carried out will remain lit When the programme has finished the End light comes on O Prewash Q Wash Q Rinse O Rinse hold O Drain O Spin O Filter O End The End pilot light flashes in the event of operating problems And the relative alarm code appears on the display EID the machine does not fill E20 the machine does not empty EHO the door has not been closed To eliminate the problem see paragraph Something not working pages 25 26 ATTENTION If you turn the programme selector d
37. undry in the drum one item at a time shaking them out as much as possible Close the door 2 Measure out the detergent Pull out the dispenser drawer until it stops Measure out the amount of detergent required and pour it into the main wash compartment Il If you wish to carry out the prewash a soak programme or a stain phase pour detergent or stain remover into the appropriate compartment marked Important Do not use normal detergent for the Stain option always use a STAIN remover 3 Measure out the fabric softener If required pour fabric softener into the compartment marked amp without exceeding the MAX mark Close the drawer gently 4 Switch the machine on Turn the selector dial to any programme to switch the machine on To switch the appliance off turn it to off 5 Select the desired programme temperature Turn the selector dial to the desired position Cottons 90 in this case The lights relevant to the phases that form the programme will light up The display will show the duration of the selected programme calculated on the basis of the maximum load for each type of fabric The Start Pause button light will start flashing If the load of laundry to be washed is small at the beginning of the cycle the display will still indicate the duration relevant to the maximum load The duration value will be gradually adjusted during the cycle O Prewash O Wash O R
38. w Slide out the relevant pin Fill all the holes with the plastic plugs supplied with the instruction booklet P0002 Positioning Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Check that the machine does not touch the wall or other kitchen units Never place cardboard wood or similar materials under the machine to compensate for any unevenness in the floor If the floor is carpeted or covered with crumbly or soft material insert a rigid support base under the feet to prevent noise vibration or displacement The base should protrude a few centimetres beyond the edges of the machine Warning A The machine should NOT be placed on deep pile carpeting Installation on a Suspended Floor Suspended wooden floors are particularly susceptible to vibration To help prevent vibration we recommend you place a waterproof wood panel at least 15 mm thick under the appliance secured to at least 2 floor beams with screws If possible install the appliance in one of the corners of the room where the floor is more stable Note Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown Plumbing In Your new washing machine has been designed to be permanently plumbed in to your home s water supply and drainage system However if this is not possible it may
Download Pdf Manuals
Related Search