JAMO F35 Automobile Alarm User Manual
Contents
1. 5 GROUND BLACK Refer to the programming instructions on pages 9 11 4 7 DISARM OVERRIDE BUTTON INPUT GROUND PLUG IN 8 DISARM OVERRRIDE BUTTON GROUND 1 ARMED OUTPUT WHITE BLUE 2 UNLOCK SENSE LIGHT GREEN 3 TRUNK MOTOR OUTPUT TAN 4 UNLOCK MOTOR OUTPUT GREEN 5 UNUSED 6 HORN SIREN 1 AMP BLACK 9 HOOD PIN INPUT GRAY 20 DOOR TRIGGER INPUT GREEN VIOLET 7 IGNITION 1 INPUT OUTPUT PINK 0 UNUSED 6 STARTER KEY VIOLET RED 8 STARTER MOTOR VIOLET 9 DISARM INPUT Basic Harness 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 View from wire end 21 TRUNK 500mA BROWN BLACK 22 LED 2 RED PLUG IN 23 LED 1 BLACK PLUG IN 24 ILLUMINATED ENTRY BLUE GREEN Programming Selectable Options 9 Programming Selectable Options using a generic Code Alarm i lt N remote Programming the Remote Transmitter Open the driver s door Turn vehicle ignition on Press and hold emergency override button After 15 seconds the siren or horn will sound three 3 times This indicates that the unit has entered the transmitter programming mode Release the button Press the Arm button on the remote transmitter to be programmed The siren or horn will sound once indicating that the system has learned that remote transmitter Programming Options Repeat steps 1 4 of Programming the RemoteTransmitter Pr2. If the above conditions are met make your request for payment by submitting the following to CODE The request for payment must be received by CODE no later than sixty 60 days after the vehicle is reported stolen 1 Copy of the retail sales receipt for the purchase of the security system clearing showing the model of system purchased and the year make and model of the vehicle in which the system was installed 2 A copy of the police report for the stolen vehicle 3 A copy of the paid insurance claim and reimbursement check from the insurance company Send the above items to CODE by certified mail at the following address CODE ALARIM INC Consumer Affairs Department 950 E Whitcomb Madison Heights MI 48071 1 800 421 3209 12 CODE ALARM INC 3 YEAR WARRANTY A CODE ALAR M INC CODE vehicle system sold to a retail consumer purchaser by an authorized dealer of CODE and installed by an authorized dealer of CODE is warranted by CODE to the original retail consumer purchaser to be free from defects in workmanship and materials for three 3 years from when the system was originally installed A CODE vehicle system sold to a retail consumer purchaser by an authorized dealer of CODE and installed by a party other than an authorized dealer of CODE is warranted by CODE to the original retail consumer purchaser to be free from defects in workmanship and materials for a period of ninety 90 days Defects caused by or related to th
3. F35 OEM Keyless Integration The F30 F35 utilizes your factory keyless entry remote controls and adds a complete vehicle security system while retaining factory functions All Entrances Protected Opening any door or entrance protected by the security system triggers the vehicle s horn and flashes the vehicle parking lights Starter Disable The F30 F35 protects your vehicle from theft by disabling the starter when the system is armed IT s Interior Theft Sensor This patented sensor uses infra red technology to reliably detect vehicle impact associated with attempted intrusion The IT s sensor guards against vehicle body damage and theft car equipment such as airbags and personal belongings Interior Status Indicator The bright red warning light is an effective visual deterrent to a would be thief 4 Using Your Existing Remote Transmitter Existing Keyless Entry or Security Remote Arming the Security System To arm the system exit the vehicle close all doors then press the LOCK button on your OEM Keyless Entry Remote Control The horn will chirp twicet and the parking lights will flash twice indicating the system is armed The status indicator red warning light on the dash will blink steadily once per second Pre arm Mode If the horn chirps and the parking lights flash only once this indicates that the vehicle courtesy light is on or that an entrance is not closed securely Check to see that door
4. Symptom Remote control does Weak or dead battery Change battery not work Close entrance Door or other entrance is open System will not arm Courtesy light is on Turn courtesy light off System is in Valet Turn off Valet mode mode page 5 FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Programming Selectable Options cont d 11 Default settings in BOLD OPTION DESCRIPTION Option Bank 0 3 Chirps Learn Transmitters Option Bank One 4 Chirps Keyless Options STATUS INDICATOR 1 Lock with Ignition Doors lock when all doors are closed and ON OF ignition is turned on 2 Delayed Door Lock 3 sec delay locking for theater dimming ON OF 3 Extended Locks Lock duration is 1 5 sec or 2 0 6 sec ON 1 OFF 2 4 Unlock with Ignition Doors unlock when ignition is turned off ON OFF 5 Double Unlock Pulse Unit provides two pulses on each unlock ON OF 6 Silent Choice 1 By pressing LOCK or UNLOCK twice manual ON 1 OFF 2 7 60 Second Pre Arm ON OFF Option Bank Two 5 Chirps
5. by accident physical or electrical abuse improper installation alteration any use contrary to its intended function unauthorized service i e service by anyone other than CODE or its authorized service personnel fire flood lightning or other acts of God Should a product be found to be defective during the warranty duration CODE will repair or replace the product or any part of the product that CODE agrees is defective without charge to the retail consumer purchaser of the product during the first year of the warranty period After the first year of the warranty period has expired CODE will repair or replace the product or any part of the product that CODE agrees is defective for a fee of 10 00 to cover shipping and handling charges In order for a product to be repaired or replaced under the terms of this warranty the defective product must be returned to an authorized CODE dealer and accompanied by a copy of the original retail sales receipt The date of purchase and year make and model of the vehicle in which the system was originally installed must be clearly indicated on the sales receipt CODE shall not be held responsible for any removal and or reinstallation charges of a defective product damage to or theft of the vehicle or its contents or any incidental or consequential damages caused by any failure of the product to function properly Under no circumstances should this warranty or product covered by it be construed as an i
6. CHANGE ALTER MODIFY OR DISCONTINUE ALL OR PART OF THIS THEFT PROTECTION PROGRAM WITHOUT PRIOR NOTICE THIS THEFT PROTECTION PROGRAM IS NOT AN INSURANCE POLICY AND SHOULD NOT REPLACE AN AUTOMO BILE OR HOMEOWNERS INSURANCE POLICY THIS THEFT PRO TECTION PROGRAM DOES NOT COVER LOSSES ARISING FROM THE THEFT OF ITEMS WITHIN THE AUTOMOBILE OR ANY DAM AGES ARISING FROM RELEATED TO AND OR INCIDENTAL OR A CONSEQUENCE OF A VEHICLE THEFT EXCEPT AS SPECIFICALLY DELINEATED BELOW Plan duration 1Year from the date of installation Plan amount F30 F35 cccceeesseeees Maximum allowable value equal to insurance deductible or up to 2 500 whichever is less Conditions of the Theft Protection Program 1 The Theft Protection Program is non transferable and non assignable 2 The system must be installed by an authorized CODE dealer 3 Vehicle must be less than three 3 model years old at the time of installation 4 The security system must have been fully armed at the time of the vehicle theft 5 The vehicle in which the system is installed must be insured for theft by a licensed insurance underwriter in the state in which the vehicle is registered Terms of payment 1 The vehicle must first be considered a total loss due to theft by your insurance company 2 Your insurance company has settled all claims arising from this theft and there are no other pending legal actions as a result of this theft How to file a request for payment
7. F30 F35 Remote Vehicle Control System OEM Keyless Entry Upgrade Security System IMPORTANT NOTE The operation of the F30 F35 as described in this manual is applicable to most vehicles However due to the engine type and configuration of some vehicles i e diesel engines some functions AND OR SAFETY PRECAUTIONS may not apply Please see your 101102 3 installing dealer for more information 9 01 2 Table of Contents Features and Benefits of the F30 F35 ecsecssssseeeeeees 3 Arming the Security Syatem cccseesseesseeeseseeeeseeesseeneeeeenes 4 Turning on the Vehicle Headlights Using the Car Finder Feature Personal Protection Alarm Panic When Your Security System is Triggered ssccsseeseeeeees 5 The Interior Status Indicator ceseeeseeeseeeeseeeeeeeeeeseeeneeeenes 5 Basic Troubleshooting eccceeseeeseseeeeeseeeneseseeeeseeeeeesseeeneeeenens 6 Emergency Disarm Procedure Emergency Disarm Button Location Installer Programmed Options System LayOut eiciscscicicccccteccassectetventececieesctinereve naisina naian 8 Remote Transmitter Programming s sssssussssennnennnnnnennnnnnnnnnnne 9 Programming Selectable Options ss ssssssssssunnesnunnrnnnnnennnnnennne 9 Code Alarm WarrantyPlan ccscccsesseesseeeeseeeeeseeesseeenseeenes 12 Code Alarm theft Protection Plan ccccccccsssssesseeeeeseeeseeeeees 13 Features and Benefits of the F30
8. Keyless amp Alarm Options 1 Passive Starter Kill Engages starter kill after one minute ON OF 2 Passive Arming Alarm automatically arms 60 sec ON OF after ignition is turned off 3 Passive Door Locks Doors lock automatically when alarm ON OFF passively arms Alarm will 1 sound for five 30 sec cycles _ ON 1 OFF 2 then ignore trigger or 2 Sound continuously when triggered if an entrance is left open 1 Real Panic 2 Steady Pulsed 4 Noise Control 5 Real Panic Sound 1 ON 2 OFF OPTION DESCRIPTION Option Bank Three 6 Chirps Installer Options 1 Door Trigger Polarity 1 Positive 2 Negative 2 Keyless Mode STATUS INDICATOR ON 1 OFF 2 ON 1 OFF 2 3 Horn siren 1 Horn 2 Siren ON 1 OFF 2 4 Unused Do Not Change 5 UnlockSensePolarity 1 Positive 2 Negatiive ON 1 OFF 2 G LightTouchagj ARMraisessensitivity DISARMlowerssensitivity ON OFF 7 FullShockad ARM raisessensitivity DISARMlowerssensitivity e OFF 10 Programming Selectable Options cont d Emergency Disarm Procedure Note The following section describes programming options without using a remote transmitter This programming method can be used for all options programming with the exception of IT s sensor sensitivity adjustments When adjusting the IT s 1 Use the keys to enter the vehicle sensor a programmed remote must be used The alarm will sound once the door is opened If your remote control is lost or fails to functio
9. e improper installation of the system are not covered by this or any other warranty The duration of this warranty described above applies to all components of the system except for switches indicator lights transmitter s and accessories purchased separately Transmitters exclusive of the transmitter case are warranted by CODE to the original retail consumer purchaser to be free from defects in workmanship and materials for three 3 years from when the system was originally installed Switches indicator lights and transmitter cases are warranted to the original consumer purchaser for a period of one 1 year from the date of purchase when the system is installed by an authorized CODE dealer Switches indicator lights and transmitter cases are warranted to the original consumer purchaser for a period of ninety 90 days from the date of purchase when the system is installed by a party other than an authorized CODE dealer System accessories are covered by the warranty supplied with the accessory Wiring harnesses altered by installation and transmitter batteries are not covered by this or any other warranty This warranty is non transferable non assignable and is completely voided when the system is removed from the car in which it was originally installed If the vehicle in which the system was originally installed is transferred to another party this warranty no longer applies This warranty does not apply to any product damaged
10. ess and release the emergency override button The horn or siren will sound four 4 times This indicates that the unit has entered the Keyless Options Programming mode Press the FIND PANIC button to advance to the next feature The siren or horn will sound a number of times to indicate the number of the option Press the ARM button to turn the option on or off The vehicle status indicator on the dashboard indicates whether an option is on or off If the selected option is ON the indicator will light If the selected option is OFF the indicator will turn off The status indicator will turn on or off when an option is changed 5 When changes are complete press and release the emergency override button to continue to the next option bank Siren or horn will sound five 5 times 6 To reset all options back to factory defaults press the DISARM button Note Option Bank Installer options will never reset 7 Turn ignition off to exit programming See Programmable Options Chart on Page 11
11. he ignition on then turn off 3 times within 5 seconds When Your Security System is Triggered The F30 F35 will trigger if one of the following events occurs while the system is armed e Any protected entrance is opened e The vehicle ignition is turned on e The vehicle is jolted hard enough to signal the impact detector Once the alarm is triggered the siren or horn sounds and the vehicle parking lights flash for 30 seconds The system will then re arm awaiting the next intrusion attempt To stop the siren while keeping the alarm armed and doors locked press the LOCK button on the OEM Keyless Entry Remote while the system is triggered The Interior Status Indicator The Status Indicator is a high intensity red light mounted in a visible location on the vehicle dashboard This red light gives a visual indication of the alarm system s state of operation Note the chart below If the Status Indicator is then the Security System Off is disarmed Flashing Slowly is armed Flashing Very Quickly was triggered in your absence see Attempted Intrusion ID page 4 Flashing Intermittently is in Valet mode 2 flashes off 2 flashes On not flashing is in Pre arm mode 6 Basic Troubleshooting This section outlines some of the basic issues you may experience while becoming used to the F30 F35 If you have a problem that is not covered by this section please consult your installer Solution Problem
12. n use this procedure to disarm the F30 F35 and start your vehicle Alternative Method for Programming Selectable Option s 2 Insert the key into the ignition and turn to the ON position 1 Open the driver s door 3 Locate and press the emergency override button 2 Turn vehicle ignition on The alarm will turn off and then you will be able to 3 Press and hold emergency override button After 15 seconds stareyourvenicle the horn will chirp three 3 times This indicates that the unit has entered the transmitter programming mode 4 Release then press and release the button again The horn will Your Emergency Disarm Button is located chirp 4 times indicating the the unit has entered the programming options mode 5 Press vehicle s lock switch to advance to the next feature The siren or horn will sound a number of times to indicate the number of the option 6 Press vehicle s unlock switch to turn the option on or off The vehicle The vehicle status indicator on the dashboard indicates Installer Programmed Options whether an option is on or off If the selected option is ON the indicator will light If the selected option is OFF the indicator will turn off The status indicator will turn on or off when an option is changed 8 System Layout IMPORTANT The module MUST be programmed before it will operate 1 PARKING LIGHT OUTPUT WHITE 2 LOCK MOTOR OUTPUT BLUE 3 UNUSED 4 BATTERY 12V RED
13. nsurance policy against loss CODE neither assumes nor authorizes any person or organization to make ANY WARRANTIES or assume any liability in connection with the sale installation or use of this product This is the complete CODE warranty and no other warranty exists The warranty identified in this form is exclusive and CODE makes no other warranties expressed or implied for any goods or services provided by CODE CODE specifically and expressly excludes any other warranties including the fitness for a particular purpose and all warranties of merchantability The customer s sole and exclusive remedy for any and all claims against CODE arising out of the customers use of any CODE vehicle system or component shall be as delineated in the warranty set forth above CODE shall not be liable to any customer or any other person or entity for any direct or indirect consequential special or exemplary damages arising out of or in connection with the customers use of or inability to use or misuse of any CODE provided product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Using Your Remote Transmitter cont To enter valet mode With the key turn the ignition on then turn off 3 times within 5 seconds To exit Valet mode With the key turn t
14. s hood and trunk are properly closed Once all entrances are secured and the courtesy light is off the system will chirp flash again The system is now fully armed If the entrance is not secured within 4 minutes the system will arm and ignore the unsecured entrance until it is closed Disarming the Security System To disarm the system press the UNLOCK button on your OEM Keyless Entry Remote Control The siren will chirp and the parking lights will flash once Attempted Intrusion Identification If the horn chirps four times when disarming this indicates that the system was triggered in your absence The status indicator will also flash rapidly Perform the following operation to determine the protected zone that triggered the system After disarming press the emergency override button The siren will chirp to indicate the cause of the alarm trigger 1 chirp IT s Interior Theft Sensor 2 chirps Door 3 chirps Hood 4 chirps Trunk Optional Sensors 5 chirps Ignition was turned on CODE ALAR M INC Theft Protection Plan The Theft Protection Program is designed to provide the retail pur chaser of a security system provided by CODE ALARM INC CODE an additional benefit at no additional cost to the purchaser should their vehicle be stolen while protected by a CODE ALARM security system While CODE has created this program as a way of showing appreciation to its customers CODE RESERVES THE RIGHT TO UNILATERALLY
Download Pdf Manuals
Related Search