Iveco N40 ENT M25 Automobile Parts User Manual
Contents
1. emergency mode The possible operating modes are as follows A The accelerator lever does not respond the running speed stabilises at 750 rpm to allow the vessel to proceed slowly and be manouevered simply by turning the marine gear on and off with out accelerating B he accelerator lever responds partially the minimum running speed is set to 750 rpm When the accelerator lever is moved to approximately half way the speed gradually increases up to 2000 rpm when the lever is returned to minimum the speed rapidly decreases to 50 rpm 38 CAUTION The engine electronic control unit can adopt safety strategies at any time during navigation should conditions arise that are considered to put the engine at risk When conditions of this kind occur proceed with the greatest possible care and attention first making sure that all those on board are secure and holding on to safe hand holds NOTE In mode it is possible to proceed at speeds higher than the accelerated minimum managing start stop acceleration and deceleration functions as illustrated in the section MANAGING THE ENGINE FROM THE RELAY BOX Should be necessary to operate the engine as above always comply with the accident prevention rules provided in the Section Controls and maintenance CAUTION Management of the engine from the Relay box involves inhibition of the bridge controls as a result of this when running the2. 300 hours 300 hours 0 600 hours 600 hours 0 9 600 hours 0 5 600 hours see relevant details yearly yearly 1200 hours or 2 years 2 years 2 years Special maintenance Frequency Check wear In sea water pump rotor 900 hours Replace belt 1200 hours or 2 years Clean heat exchangers 2 years 9 Clean the turbocharger 2 years Adjust play in valves rocker arms 3000 hours Maximum period when using good quality fuel EN 590 standard this is reduced if the fuel is contaminated and alarms are triggered due to blockage of the filters and presence of water in the pre filter When blockage of the filter is indicated it must be replaced If the water in pre filter indicator does not go out after drainage the pre filter must be replaced 2 The frequency with which operations are carried out will depend on the working conditions and efficiency wear of the product If the engine is not used for long periods of time check it before you start it SING 4 The anode must be replaced if corrosion has exceeded 5076 of the volume of zinc 27 5 Replace lubricants according to the frequency indicated in the REFUELLING table 6 Sea water combustion air heat exchanger clean both the air and water sections engine coolant sea water heat exchanger clean the sea water section optional sea water marine gear oil heat exchanger clean the sea water section 7 Must be performed annuall
3. 8 Fit signs reading ENGINE WITHOUT OIL to the engine and to the on board control panel 9 Drain the coolant if it has not been mixed with suitable antifreeze and corrosion inhibitors and affix a sign to indicate the fact In the event of prolonged inactivity the operations described must be repeated every 6 months following the procedure given below A drain the 30 M protective oil from the sump B repeat the operations described from point 2 to point 7 Should you intend to protect external parts of the engine proceed by spraying OVER 19 AR protective liquid on unpainted metal parts such as the flywheel pulleys and the like avoiding belts connector cables and electrical equipment RESTARTING THE ENGINE AFTER A LONG PERIOD OF INACTIVITY 1 2 p Drain the residual 30 M protective oil from the sump Fill the engine as prescribed with lubricant of the type and amount indicated in the table REFUELLING Drain the CFB protective fluid from the fuel circuit carrying out this operation as indicated under point 3 of PREPARING THE ENGINE FOR A LONG PERIOD OF INACTIVITY Remove the plugs and or seals from the suction delivery ventilation and bleeder openings in the engine restoring it to a normal state of use Connect the turbocharger suction inlet to the air filter Connect the fuel circuits to the vessel s fuel tank completing the operations as indicated in point 4 of PREPARING THE ENGINE FOR A L
4. he dridleeue o 12 RECOCRISING Sat o acude pod dor dunt eee daha re de 15 Starting and stopping the engine from medet contiol panel vs vq te redd 16 pisse cncacicn mM 18 Managing the engine from the Relay 21 Proper use Cl INS Spe 22 WV REA 22 KU A M CE EE 2 3 Ac I A oS 24 CONTROLS AND MAINTENANCE 25 dope ance Dese iei acr eer ataca gente eee gree erence eee 25 EVEMON erir rea E 29 RPCOUCIC Ga P PERPE eee Sere weet eae 26 IS SOLES PIOS nh Oo cuore eum 28 mic RUG TOC A ee ee nae 28 PIOVE Cede nel 33 E E E E ATE 35 GENERAL INFORMATION GUARANTEE In order to ensure that your engine gives the best possible performance and to take advantage of the IVECO MOTORS guarantee you must follow the indications provided in this publication with great care failure to do so may result in invalidation of the guarantee SPARE PARTS Always use Onginal IVECO MOTORS Spare parts This is essential to keep the engine in original running order The use of non original spare parts will not only invalidate the guarantee but will mean that IVECO MOTORS will not be considered liable in any way during the whole worki
5. available If the Boatyard uses different technical options there may also be changes to the above Operation When the key switch 15 tumed to position 8B the signals and alarms module will perform an efficiency test on all the indicator lights lasting 5 seconds with the exception of the Pre lubrication Pre post heating EDG system malfunction indicators and simultaneously the beeper sounds It is possible to stop the beeper before the end of the test by pressing the relevant button Dunng start up and for the following 15 seconds all alarm functions are disabled after this period each alarm detected by the sensors provided on the engine will result in the relevant indicator flashing and a simultaneous warming sound from the beeper If the beeper is disabled by pressing the relevant button the indicator light will tum on without flashing and the alarm will be stored until the engine is next stopped 15 esc Dee esses feed dee Ca secos 04 234 N 1 Maximum allowed rotation speed exceeded on request 2 Water in the fuel pre filter 3 Engine coolant level low 4 Alternator malfunction 5 Oil filter blocked 6 Oil vapour filter blocked 7 Pre lubrication in progress 8 Air filter blocked 9 Fuel filter blocked 10 Coolant temperature high 11 Oil pressure low 12 Pre post heating 13 Malfunction in EDC electronic injection system Alarm funct
6. relative humidity 30 WARNING Any alteration of the above mentioned characteristics in particular modification of the data stored in the injection system electronic units or the characteristics of the engine and its fittings is strictly prohibited penalty invalidation of the guarantee and absence of all liability on the part of IVECO MOTORS 9 000 OF C 2 I aa gt 04 352 N Engine NEF N60 ENT M37 M40 1 Exhaust gas and sea water discharge 2 Turbocharger 3 Engine coolant sea water heat exchanger 4 Coolant outlet manifold from engine 5 Oil filter 6 Lifting U bolt 7 Coolant filler cap 8 Thermostat valve location 9 Alternator 10 Manifold connecting the cooling circuit to the coolant tank 11 Coolant infeed to engine 12 Water heater system tap or plug 13 Coolant discharge plug 14 Connection to battery positive terminal 15 Electrical starter motor 16 Removable anode 1 JB 3 5 6 8 YW w MA AN p ENGLISH 49 0 1 5 wj s Engine NEF N60 ENT M37 M40 1 Coolant expansion tank 2 Oil extraction pump 3 Oil filler cap 4 Oil dipstick 5 Common rail divider 6 Sea water pump inlet 7 Lifting U bolt 8 Oil vapour filter 9 Sea water circuit connector pipe 10 Air filter 11 High pressure pump for common rail system 12 Fuel inlet from tank 13 Fuel outlet to tank 14 Fuel filter 15 Rem
7. after start up an uncontrolled increase in engine speed were to occur L 2 O 2 Tm CAUTION Do not carry out maintenance operations when the electric power supply is turned on always check to ensure that the appliances are properly earthed During diagnosis and maintenance operations make sure that your hands and feet are dry and whenever possible use insulating stands FREQUENCY Controls Frequency Check oil level in engine Daily Check oil level in marine gear Daily Check engine coolant level Daily Check exhaust pipe s for damage Daily Drain water from the fuel pre filter 150 hours Check top up electrolyte level in batteries and clean terminals Half yearly The maintenance intervals indicated below take into account the typical working factors for various types of engine use the most suitable interval for maintenance operations for the various applications will be indicated by the maintenance staff according to the way and working conditions in which the engine is used 26 Planned maintenance Clean air filter s Check corrosion of zinc anodes Check state of oil vapour filter Drain suck condensation from fuel tank s Change engine oil Change oll filter s Change fuel filter s Change fuel pre filter Change oil in the marine gear Inspect sea chest Check tension and state of belt Change coolant Change air filter Change oil vapour filter s Frequency 300 hours 300 hours 0
8. and hour counter 3 Voltmeter 4 Beeper 5 Indicator and alarm module 6 Engine oil pressure indicator Control panel instrument light switch 8 Key switch to start stop the engine 9 Button to stop the engine 10 Button to disable the beeper Detail of the key switch 8A sc 04 356 N Procedure for start up from IVECO MOTORS secondary or fly bridge control panel supplied on demand 1 Enable the secondary control panel by turning the key switch on the main panel to position 8B see warnings and procedure given in previous paragraph 2 Wait for the beeper to stop sounding and for the alarm indicators on the indicator module 3 to switch off with the exception of the alternator recharge and low oil pressure indicators At the same time check that the indicator test has been performed successfully information on how to interpret this test and indications on the module are given in the relevant paragraph 3 Press the green button 5 and release it when the engine has started 4 Check that the rev indicator shows a plausible value ds JE Moroes 1 Rev counter and hour counter 2 Beeper 3 Indicator and alarm module 4 Button to disable the beeper 5 Engine start button 6 Engine stop button L 2 2 Stopping the engine Before stopping the engine it is recommended you run it for a few minutes at minimum speed with no load this will allow th
9. and relevant equipment only make some of the above mentioned functions available If the Boatyard uses different technical options there may also be changes to the above y Air filter i blocked Oil vapour filter blocked 2 SRE es Maintenance Alternator SAA interval expired malfunction Oil filter blocked Oil pressure low Pre lubrication In progress Coolant temperature high Pre post heating Over revs E 2 Su Alarm functions not available with standard setup Fuel filter blocked Coolant level low Water in the fuel filter EDC engine control system malfunction 04 359 N Operation When the key switch is turned to position 8B an efficiency test will be performed on all the indicator lights lasting 5 seconds with the exception of the Pre lubnication Pre post heating EDC electronic injection system malfunction indicators and simultaneously the beeper sounds It is possible to stop the beeper before the end of the test by pressing the relevant button During start up and for the following 15 seconds all alarm functions are disabled after this period each alarm detected by the sensors provided on the engine will result in the relevant indicator flashing and a simultaneous warming sound from the beeper If the beeper is disabled by pressing the relevant button the indicator light will tum on without flashing and the alarm will be stored un
10. started up and used until the vessel in which it installed has satisfied all necessary safety requirements or until the vessel has been guaranteed to comply with local laws and regulations Q The operations required to guarantee the best possible use and preservation of the engine must only be carried out by persons of proven experience equipment with tools considered suitable by IVECO MOTORS For the purpose of safety further recommendations are given in the chapter CONTROLS AND MAINTENANCE L 2 2 ENGINE TECHNICAL DATA N40 ENT M25 The technical code and serial number are indicated on a plate which is Available settings located on different parts of the engine according to the model flywheel n casing tappet cover coolant tank N40 ENT M25 184 kW 250 CV 2800 rpm B 147 kW 200 CV 2800 rpm Code N40 ENT M25 e 125 kW 170 CV 2800 rpm Engine family F4 E C CL U Lu LL LUIOIO GI Cycle 4 stroke diesel Net power to the flywheel in compliance with ISO 3046 1 Test Number and arrangement of cylinders Bore x stroke Total displacement Air system Injection type Engine direction of rotation Dry weight Electrical system Accumulator s capacity discharge current 4 In line 102 x 120 mm 3 900 cm Supercharged aftercooled ICA or TAA Direct Common rail electronically managed Anticlockwise seen from flywheel side 490 kg 12 V 24 V on request 180 Ah or above 800
11. that satisfy the needs of the engine e g by comparing them with the old one pre filter Damp the new filter seal with diesel or engine oll Hand screw the new filter into place until the seal gasket touches the support then lock by a further 3 4 of a turn Loosen the bleeder screw 2 on the pre filter support and activate the hand pump 1 until the supply circuit is full Ensure that any fuel coming out is not dispersed into the environment 04 361 N Lock the bleeder screw tightly LI Start the engine and run it at minimum speed for a few minutes to eliminate any residual air NOTE should it be necessary to accelerate the bleeding phase the hand pump can be used during start up Check tension and state of the auxiliary member drive belt Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Remove the casing protecting the pulleys LI Check that the pulleys are not torn or worn and that there are no lubricants or fuel on them If this is not the case replace them L At the same time make sure that the tensioning device is working 2 properly proceeding as indicated in the figure J Q Replace the guard casing in its housing and lock all the seal elements LNG 2 i ma as 4 WO 74178 33 Replace coolant Only proceed with the engine stopped and at a low temperature so as to avoid th
12. the fuel tank only a small reserve of fuel this encourages the formation of condensation and makes it more likely you will suck up dirt or air resulting in engine stoppage CAUTION When refuelling always pay great care to ensure that no solid or liquid pollutants enter the fuel tank you must also remember that smoking and live flames are prohibited when refuelling Air filter blocked and exhaust circuit inefficient Inspect the cleanliness of the air intakes and discharge pipes on a regular basis The maintenance intervals indicated in this manual only take into account the performance of engine components and not any additional fittings installed by the Boatbuilder and any external events CAUTION Visually check that the exhaust circuit is not blocked or damaged so as to prevent dangerous fumes within the vessel A 23 Alternator malfunction Check it or have it checked periodically for cleanliness wear and proper tensioning of the drive belt CAUTION The drive members are located under protective casings These must only be removed when the engine is not turning A Irregularities in the electrical system Periodically check particularly during the winter to ensure that the batteries are clean and in full working order checking and topping up as indicated in the section CONTROLS AND MAINTENANCE always taking due note of the WARNINGS provided If it should be necessary to replace them always
13. value in hours set previously release the buttons and press just the Scroll select button 10 repeatedly until the prescribed value as indicated in the section FREQUENCY is shown and flashes after which press the Prog button 9 to confirm the value and start the new count B The information on instant fuel consumption requires the maximum input value to be correctly programmed with respect to the performance of the engine fitted on the vessel to check this proceed as follows If the value does not correspond modify it by pressing and holding the Prog button 9 until the display shows the maximum input value e g 131 mg strk then release the button and compare the value with the ones provided in the table below If the value does not correspond modify it by pressing the Scroll select button 10 repeatedly until the prescribed value is displayed flashing Press and hold the Prog button 9 until the display shows the engine running speed which indicates that the value has been stored If the programming operations have not been carried out correctly the display will indicate P Err 5 in this case it will be necessary to repeat the procedure from the beginning 20 N40 ENT M25 Maximum power CV 250 200 170 N60 ENT M37 Maximum power CV 370 330 2 0 N60 ENT M40 Maximum power CV 400 3 0 330 270 N67 ENT M45 Maximum power CV 331 309 2 2 258 Maximum input mg strk 128 108 95
14. A or above conditions T 25 C atmospheric pressure 100 kPa relative humidity 3076 Any alteration of the above mentioned characteristics in particular modification of the data stored in the injection system electronic units or the characteristics of the engine and its fittings is strictly prohibited penalty invalidation of the guarantee and absence of all liability on the part of IVECO MOTORS wW 53 06 2 8Jl9 5 9 B UN eed A AG Engine NEF N40 ENT M25 1 Exhaust gas and sea water discharge 2 Turbocharger 3 Engine coolant sea water heat exchanger 4 Coolant outlet manifold from engine 5 Oil filter 6 Lifting U bolt 7 Coolant filler cap 8 Thermostat valve location 9 Alternator 10 Manifold connecting the cooling circuit to the coolant tank 11 Coolant infeed to engine 12 W ater heater system tap or plug 13 Connection to battery positive terminal 14 Coolant discharge plug 15 Electrical starter motor 16 Removable anode 04 363 N a UJ 3 4 5 6 7 8 Wy yo it oe i e EN T XT NU L EAR as 17 16 15 Engine NEF N40 ENT M25 1 Coolant expansion tank 2 Oil extraction pump 3 Oil dipstick 4 Oil filler cap 5 Common rail divider 6 Sea water pump inlet 7 Lifting U bolt 8 Oil vapour filter 9 Sea water circuit connecto
15. CAUTION Q The batteries contain sulphuric acid which is extremely caustic and corrosive always wear protective gloves and goggles when topping them up Whenever possible it is recommended that this contro be carried out by specialised personnel Do not smoke or use live flames near the batteries during controls and make sure that the room you are working in is adequately ventilated Some types of battery have a single cover for all the inspection plugs To access the elements use a lever as shown in the figure 04 362 N 30 Cleaning the air filter LJ Remove the filter by loosening the screws 4 indicated in the figure LI Blow dehumidified compressed air through the filter element from the inside outward maximum pressure 200 kPa or wash with water only Do not use detergents do not use diesel Replace the filter if any breakages are found Replace the filter once every 2 years Restore normal operating conditions after positioning the filter in its housing 04 007 N Check corrosion of zinc anodes Only proceed with the engine stopped and at a low temperature Provide suitable containers to ensure that no water is dispersed inside the vessel during removal of the anodes LI Remove the anodes unscrewing them from their housings see location in the section ENGINE TECHNICAL DATA LJ Make sure that corrosion has not exceeded 50 of the volume of zinc If this is the case cha
16. IC STN 1 Engine coolant temperature indicator 2 Lubrication circuit pressure indicator 3 Service and alarm signals 4 Rev counter 5 Supercharged air pressure indicator 6 Voltmeter 7 Alpha numenc display 8 Key switch to start stop the engine 9 Accessory function programming button 10 Button used to scroll through and select additional information 11 Button to reset the planned maintenance indicator 12 Button to disable the beeper 13 Beeper O 04 356 N Detail of the key switch Procedure for start up from IVECO MOTORS secondary or fly bridge control panel supplied on By _ demand 1 MOTORS 1 Enable the secondary control panel by turning the key switch on the main panel to position 8B requirements and procedure 2 given in previous paragraph 2 Wait for the beeper to stop sounding and for the alarm indicator lights to switch off with the exception of the Alarm malfunction 1 ie 6 T and Low oll pressure indicators At the same time check that the 1 C Py v T indicator test has been performed successfully see the section on 7 Z RECOGNIZING ALARMS 3 Press the green START button 11 and release it when the engine START z STOP has started making sure that the instruments with analogue displays are showing values that conform with the new physical parameters 9 1 Engine coo
17. Maximum input mg strk 131 116 98 Maximum input mg strk 132 131 117 98 Maximum input mg strk 450 420 370 350 MANAGING THE ENGINE FROM THE RELAY BOX The engine fittings include a unit known as the Relay box and normally installed in the engine room using which it is possible to manage the following functions Selection of the control panel bridge or engine room Q Starting and stopping the engine LI Increase and decrease of the engine speed Self diagnosis only to be used by Technical Service Network staff 04 074 N 1 Control panel selector 2 Manual start stop and accelerator command 3 Self diagnosis test and blink code emission button 4 Led indicating EDC and blink code malfunctions 5 Connector for diagnosis instrument CAUTION Never switch the ENGINE ROOM BRIDGE selector when the engine is turning A 21 Start up procedure 1 Tum switch 1 to the ENGINE ROOM position to enable the adjacent START STOP button 2 this operation disables all the on board control panel functions on the bridge and fly bridge 2 Press button 2 in the START position until the engine starts then release it Running speed management procedure Press button 2 in the START position with the engine tuming to accelerate and decelerate each time the button is pressed the engine will accelerate or decelerate in sequence 1 To accelerate press and hold button 2 in the START position u
18. ONG PERIOD OF INACTIVITY During filing operations connect the fuel return pipe to a collection tank so as to prevent any residual CFB protective fluid from flowing into the vessel s fuel tank Check the engine and fill it up with coolant as prescribed Start the engine and keep it running until the idling speed rate has stabilised completely Check that the instruments on the on board control panel s are showing plausible values and that no alarms are shown Stop the engine 10 Remove the ENGINE WITHOUT OIL signs from the engine and from the on board control panel 27 L 2 O 2 Tm E ENGINE MALFUNCTIONS The electronic unit overseeing management and control of all operation of the engine Is capable of recognising any malfunctions that may occur and of adopting strategies that will allow you to navigate in full safety The event signalled by light up of the EDC MALFUNCTION indicator on the on board control panels results in programmed limitation of power within certain thresholds set according to the severity of the case In the case of temporary malfunctions the reduction in performance will remain in force until the engine is stopped Accelerator electronic circuit malfunction When certain problems in the accelerator electric circuit are recognised the Electronic Unit controlling the engine adopts a strategy known as accelerated minimum speed running that will enable navigation to continue
19. TROL PANEL Procedure for start up from the main IVECO MOTORS control panel supplied on demand Make sure that the electrical switch indicating ENGINE ROOM BRIDGE on the Relay Box unit normally located in the engine room is in the BRIDGE position then proceed as follows 1 Lift the protective cover over the key switch 8 insert the key and turn it to the nght to position 8B Make sure that the analogue instruments are showing values that conform with the relevant physical parameters temperature battery voltage and oil pressure Wait for the beeper to stop sounding and for the alarm indicator lights on the indicator module 5 to switch off with the exception of the alternator recharge and low oil pressure indicators At the same time check that the indicator test has been performed successfully information on how to interpret this test and indications on the module are given in the relevant paragraph Turn the key to position 8C once the engine has started release the key and do not accelerate Make sure that the analogue instruments are showing values that conform with the relevant physical parameters temperature battery voltage and oil pressure If the engine does not start after releasing the key it will only be possible to turn it back to the start position after first returning the switch to the rest position 8A 12 04 354 N 1 Coolant temperature indicator 2 Rev counter
20. USE AND MAINTENANCE USO E MANUTENZIONE UTILISATION ET ENTRETIEN BETRIEB UND WARTUNG USO Y MANTENIMIENTO NEF series ELECTRONIC INJECTION SYSTEM MARINE ENGINES MOTORS IVECO e POWERTRAIN TECHNOLOGIES Publication edited by Marketing Adv amp Promotion Print L31900018 10 06 NEF SERIES ELECTRONIC INJECTION SYSTEM N40 ENT M25 N60 ENT M37 N60 ENT M40 N67 ENT M45 USE AND MAINTENANCE INTRODUCTION We would like to thank you for buying an IVECO MOTORS product and compliment you on your choice of engine Before you carry out any operation involving the engine or tts fittings please read the contents of this manual carefully compliance with the instructions provided in the manual is the best way to guarantee trouble free long term operation of the engine The contents of this manual refer to the standard configuration of the engine and the illustrations are purely indicative Some instructions are provided by giving the sequence of operations to be carried out in order to allow the engine and or its fittings to perform in a certain way In some cases they will be dependent on the configuration of the commands and the set up of the vessel on which the engine 15 installed for any points that differ from the contents of this manual please consult the instructions provided by the Boatbuilder or a specific manual The information provided below was current at the date of publication The Manufacturer reserves
21. an 90 of the speed corresponding to maximum power see section on ENGINE TECHNICAL DATA During navigation check that The engine coolant temperature does not reach the alarm threshold The oil pressure remains within normal values 22 SPECIAL WARNINGS Coolant temperature high If the temperature indicated on the instrument is considered too high or if the alarm is displayed reduce speed and return to port to check the state of the sea water intake and cooling system circuits also check and have checked tension of the water pump and alternator command belts operation of the thermostat valve whether or not the heat exchangers are clean CAUTION When the engine is warm a pressure liable to cause hot liquid to be expelled with extreme violence is created within the cooling circuits This results in a danger of burning Only open the coolant tank cap if strictly necessary and only when the engine is cold Low lubricant pressure If the pressure indicated by the instrument is considered insufficient or if the low oil pressure indicator lights up stop the engine and check the oil leve Top up if necessary see CONTROL AND MAINTENANCE section If the condition persists return to port at low speed and contact an Authorised Service Centre Water in the fuel pre filter It is a good rule to drain the water from the filters before the relevant indicator comes on Avoid using the engine with
22. ately but carefully remove any clothing that may be soaked in the hot liquid 4 Cover the burn with a special burn dressing or sterile bandage Carbon monoxide intoxication CO Carbon monoxide from the engine exhaust is without smell and is dangerous both because it causes intoxication and because when combined with air it forms an explosive mixture In closed rooms carbon monoxide is extremely dangerous as it can reach critical concentrations within a very short time When assisting an intoxicated person in a closed room 1 Ventilate the room immediately to reduce the concentration of gas 2 When entering the room hold your breath do not light flames lights or ring electric doorbells or phones to avoid the risk of explosion 3 Carry the intoxicated person out into the fresh air or into a well ventilated room resting him on one side if he is unconscious L 2 O 2 Electrocution The engine s electrical 12 V or 24 V electrical system does not involve the risk of electrocution however in the event of a short circuit caused for example by a metal tool there is a risk of burning due to overheating of the object through which the electrical current runs In these circumstances 1 Remove the object that caused the short circuit using means that provide sufficient heat insulation 2 Switch off the power at the main switch if there Is one Injuries and fractures The vast number of possible ci
23. comply with the characteristics indicated the section ENGINE TECHNICAL DATA RUNNING IN Thanks to modern engine construction technology no particular running in procedure is required However it is recommended that for the first 50 hours you do not use the engine at high power for long periods L 2 l 2 Tm REFUELLING Parts to be supplied N40 ENT N60 ENT litres kg litres kg Cooling circuit 215 245 Lubrication circuit total capacity I2 ele 15 94 19 Periodic changing sump at minimum level 9 8 9 8 oil sump at maximum level 11 10 Fuel tank _ Use a mixture of water and 50 PARAFLU 11 even during the summer months As an alternative to PARAFLU 11 you can use another product that complies with international specifications SAE J 1034 2 Use lubricants that comply with international specifications ACEA E3 E5 high power engines API CF CH4 associated with fuels with a percentage sulphur 0 526 MIL L 2104 F The viscosity level of oil to be used depending on surrounding temperatures in given in the table provided in the appendix 24 Oil consumption is considered acceptable when it reaches a maximum of 0 526 of fuel consumption 3 The amounts indicated refer to initial refuelling and include filling the engine sump and filter 4 Only use normal commercial diesel fuel EN 590 standards Do not use additives Do not use fuels derived from the s
24. e risk of burning Provide suitable containers to ensure that no coolant is dispersed into the environment L Remove the plugs on the circuit components and wait until the circuit has drained completely the location of plugs is given in the section ENGINE TECHNICAL DATA After emptying replace the plugs in their housings making sure that the seal rings are all undamaged Fill up the circuit as indicated in the table REFUELLING L Bleed the circuit and top up if necessary Change oil vapour filter figure on page 30 Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Unfasten the screws and remove the cover 5 to the filter compartment L Remove the two filters and dispose of them according to current requirements Insert the new filters and replace the cover WARNING N The operations listed below must only be carried out by qualified staff from the IVECO MOTORS Service Centres or by staff from the Boatbuilders The methods used to perform them are described in the Technical and Repair Manuals Drain suck condensation from fuel tank s Inspect sea chest Check sea water pump rotor Clean heat exchangers Clean the turbocharger Adjust play in valves rocker arms The method used to change the oil in the marine gear is indicated in the relevant documentation supplied by the Manufacturer of the marine gear itself MOVING THE ENGINE The
25. e temperature to drop evenly and will avoid harmful thermal shocks A The engine is normally stopped from the main IVECO MOTORS control panel by turning the key switch to the rest position 8A or by turning a similar command on the customised control panel B Ihe IVECO MOTORS secondary control panel is stopped by pressing the red button 6 on the control panel The main VECO MOTORS control panel for engines equipped with an excited device on request or as prescribed by the Certification Body is stopped by pressing the red button 9 To re start the engine from the main control panel 1 Return the key switch to the rest position 8A to reset all the on board control panel functions 2 Proceed as indicated To re start the engine from the secondary control panel 1 Make sure that the panel has been enabled key switch on the main control panel turned to position 8B 2 Press the green button 5 and release it when the engine has started making sure that the rev indicator is showing a plausible reading 14 RECOGNISING ALARMS IVECO MOTORS on board control panels with analogue instruments are fitted with an electronic module that includes the indicator lights and the interface timer and alarm storage circuits The figure illustrates the dial and the key indicates the meaning of the alarm signals sent by all the indicator lights some types of engine and relevant equipment only make some of the above mentioned functions
26. elling with fuel that is polluted by foreign bodies and water means that it is necessary to perform this control even if no alarm is shown on the on board control panel Proceed with the engine stopped Q Place a container under the pre filter to collect the fluid Q Unscrew the tap plug 1 in the bottom part of the pre filter in some lay outs the plug includes a sensor to detect the presence of water in the diesel L 2 T Drain off liquid until only diesel can be seen LI Close the plug again tightening it completely by hand Dispose of the drained fluids according to current requirements 04 361 N Checking the level of electrolyte solution in the batteries Place the batteries on a level surface then proceed as follows Visually check that the fluid level is between the Min and Max limits in the absence of references check that the fluid covers the Lead plates inside the elements by approximately 5 mm U If necessary top up with distilled water only those elements in which the level is below minimum Q Contact specialised technical staff if the battery needs recharging Have the efficiency of the battery recharging system tested if a voltage of less than 11 V for 12 V rated systems or 22 V for 24 V rated systems is detected with the engine running LI On this occasion make sure that the terminals and clamps are clean properly locked and protected by vaseline
27. formation and specific equipment Operations marked by the key symbol see illustration The Authorised Service Centres are the ones in the IVECO MOTORS Technical Service Network ACCIDENT PREVENTION Q Always wear heavy duty footwear and overalls LI Never wear loose flapping garments rings bracelets and or necklaces the vicinity of engines or moving parts Q Always wear protective gloves and goggles when e filing up batteries with acid solution refuelling with inhibitors or antifreeze 25 replacing or topping up lubricant hot engine oil may cause bums and scalds Only carry out these operations when the oil has dropped to a temperature of below 50 When working in the engine compartment pay particular attention to how you move to avoid contact with moving parts or high temperature components Wear goggles and use high pressure air jets maximum air pressure used to clean is 200 kPa 2 bar 30 psi 2 kg cm Q Wear a protective helmet when working in an area were there are suspended loads or systems installed at head height Use protective hand cremes Immediately replace wet overalls Always keep the engine clean removing oil grease and coolant stains LI Store cloths in flame proof containers Do not leave foreign bodies on the engine Use suitable safe containers for used oll When completing a repair make suitable provisions to stop the engine taking in air if
28. int engine only Danger of burning Expulsion of hot water under pressure Fuel Cap on the fuel tank if there is one Danger of burning Presence of high temperature parts Oil Cap Danger of fire Fuel present Danger of impact or catching on moving parts Presence of fans pulleys belts or the like Oil dipstick vi x m 10 USE STARTING AND STOPPING THE ENGINE For vessels equipped with instrument panels that PRELIMINARY CHECKS are not manufactured by IVECO MOTORS Before starting the engine each time The start up and shut down operations described below apply to an on board control panel manufactured by IVECO MOT ORS if the vessel is fitted with an instrument panel that has been customised by the Boatbuilder or Fitter these operations may vary according to the various choices made during construction In these cases follow the start up shut down sequence and use the instrument panel description provided by the Boatbuilder on specific documentation Make sure that the sea water inlet valve is open Operation of the sea water pump without water would cause irreparable damage to the internal rotor within a very few seconds L Check the level of technical fluids fuel engine oil and coolant d 2 TT Before starting the engine make sure that no combustible vapours or gasses are present in the engineroom A 11 STARTING AND STOPPING THE ENGINE FROM THE ANALOGUE CON
29. ions not available with standard setup L O 2 Tm STARTING AND STOPPING THE ENGINE FROM THE DIGITAL CONTROL PANEL Procedure for start up from the main IVECO MOTORS control panel supplied on demand Make sure that the electrical switch indicating ENGINE ROOM BRIDGE on the Relay Box unit normally located in the engine room is in the BRIDGE position then proceed as follows 1 Lift the protective cover over the key switch 8 insert the key and turn it to the nght to position 8B 2 Make sure that the instruments with analogue displays are showing values that conform with the relevant physical parameters 3 Wait for the beeper to stop sounding and for the alarm indicator lights to switch off with the exception of the Alternator malfunction and Low oil pressure indicators At the same time check that the indicator test has been performed successfully see the section on RECOGNIZING ALARMS 4 Tum the key to position 8C once the engine has started release the key and do not accelerate 5 Make sure that the instruments with analogue displays are showing values that conform with the relevant physical parameters temperature battery voltage and oil pressure 6 If the engine does not start after releasing the key it will only be possible to turn it back to the start position after first returning the switch to the rest position 8A 16 8 56 MOTORS a 5 20 aO C
30. lant temperature indicator 2 Lubrication circuit pressure indicator 3 Service and alarm signals 4 Rev counter 5 Supercharged air pressure indicator 6 Voltmeter 7 Alpha numenc display 8 Button to stop the engine 9 Button used to scroll through and select additional information 10 Button to disable the beeper 11 Engine start button 17 Stopping the engine Before stopping the engine it is recommended you run it for a few minutes at minimum speed with no load this will allow the temperature to drop evenly and will avoid harmful thermal shocks A From the main IVECO MOTORS control panel turn the key switch to the rest position 8A B From the secondary IVECO MOTORS control panel press the red STOP button 8 To re start the engine from the main control panel 1 Return the key switch to the rest position 8A to reset all the on board control panel functions 2 Proceed as indicated in the relevant paragraph To re start the engine from the secondary control panel 1 Make sure that the panel has been enabled key switch on the main control panel turned to position 8B 2 START button 11 and release it when the engine has started making sure that the instruments with analogue displays are showing plausible values 18 RECOGNISING ALARMS The following shows the meaning of the symbols associated with each of the indicator lights on the main and secondary control panels some types of engine
31. level in engine Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Using the dipstick 1 check that the oil level is between the Min and Max levels Q If the level is too low top up through the inlet on the cylinder head after first removing the relevant cap 2 Ae WARNING After topping ub make sure that the oil level does not exceed the Max limit marked on the dipstick Make sure that the dipstick is inserted properly and the filler cap is turned in a clockwise direction until it stops turning completely Check oil level in marine gear Check the oil level in the marine gear following the indications provided in the marine gear Manufacturer s manual Check coolant level Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Remove the loading tank pressurisation 3 previous page Q Visually check the coolant level Top up the tank if necessary using a mixture of 50 clean water not distilled and Paraflu 11 see REFUELLING table CAUTION Only open the coolant tank cap when the engine is cold A Check exhaust pipe s for damage Visually check that the exhaust system is not blocked or damaged Make sure that there is no risk of dangerous fumes within the vessel Contact the Boatyard if necessary 29 Draining water from the fuel pre filter The high risk of refu
32. ng life of the engine LIABILITY The Manufacturer will only be considered liable subject to performance of the control and maintenance operations indicated and described in this manual to this effect proof that these operations have been performed must be provided Any special maintenance operations that may be necessary must be carried out by qualified technicians from authorised Workshops in the IVECO MOTORS Network using the instruments and equipment provided for the purpose SAFETY The following information is intended to encourage caution when using the engine so as to avoid damage to persons or property as a result of improper or incorrect behaviour The engines must only be used for the purposes indicated by the Manufacturer Any tampering modification and use of non original spare parts may compromise proper operation of the engine and safe navigation never under any circumstances make modifications to the wiring and to the units equipping the engine or connect them to other power systems Q Pay particular attention to moving parts of the engine to high temperature components and to circuits containing pressurised fluids its electrical equipment houses electrical currents and voltage The exhaust fumes produced by the engine are bad for your health The engine must only be moved using suitable lifting tackle making use of the U bolts provided on the engine for that purpose LI The engine must not be
33. nge them Q Replace the anodes in their housings locking them to the prescribed torque Check state of oil vapour filter figure on page 30 Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Unfasten the screws and remove the cover 5 to the filter compartment LI Remove the two filters and check them for deposits if any deposits are found replace them Replace the cover in its housing Changing engine oil figure on page 30 Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Q Place a container under the hand pump 1 outlet pipe 2 to collect the used oll 31 Unscrew the filler cap turn the hand pump provided 2 which is set up to extract the oil only until the oil sump is completely empty Fill up with fresh oil through the feeder hole 3 on the timer cover using the types and amounts of oil indicated in the table REFUELLING Screw down the filler cap Using the dipstick 6 check that the oil level is between the Min and Max levels Dispose of used oil according to current requirements Changing the engine oil filter Only proceed with the engine stopped and at a low temperature so as to avoid the risk of burning Only use filters with a filtration level equivalent to the ones you are replacing see section FREQUENCY Place a container under the filter support 1 to collect
34. ntil the required engine speed is achieved then release it the speed will be maintained 2 To decelerate press button 2 again in the START position until the required decrease in speed is achieved then release it Stopping procedure 1 Press button 2 in the STOP position until the engine has come to a complete stop then release it 2 Return switch 1 to the BRIDGE position to allow use of the commands on the on board control panels and prevent use of the START STOP button in the Relay Self diagnosis procedure Use of the CHECK button 3 enables Technical Service Network staff to obtain the self diagnosis information stored in the electronic Unit controlling the engine the LED indicator 4 indicates the code by emitting flashes of light L o 2 Tm FOR PROPER USE OF THE ENGINE Do not continue to press the starter when the engine has started Do not remain in dock while waiting for the engine to warm up but after starting commence navigation at low speed the working temperature will be reached properly with the engine running at medium speeds Do not operate the engine at minimum speed for long periods as this encourages the production of harmful exhaust and does not guarantee optimum performance The engine speed must be increased and decreased gradually to allow regular combustion and proper operation of all engine components The maximum cruising speed must not be more th
35. operations necessary to embark and disembark the engine must only be carried out by technicians from Authorised Service Centres When lifting the engine only use the U bolts indicated in this manual in the section ENGINE TECHNICAL DATA and marked on the engine with special stickers Lifting must be carried out using a rocker arm that keeps the metal cables supporting the engine parallel using all the U bolts provided simultaneously the use of a single U bolt only is not allowed The engine lifting system must have a capacity and size suited to the weight and dimensions of the engine check that there is no interference between the lifting system and the engine components Do not lift the engine before removing the transmission members that are coupled to tt DS DISPOSAL OF WASTE The engine is made up of parts and elements that if discarded may cause damage to the environment he materials listed below must be handed over to specialised Collection Centres the laws in force in the various Countries foresee severe penalties for transgressors Starter batteries L Used lubricants L Mixtures of water and antifreeze Filters Q Additional cleaning materials e g greasy or fuel soaked cloths L 2 O 2 Tm E LONG PERIODS OF INACTIVITY PREPARING THE ENGINE FOR A LONG PERIOD OF INACTIVITY In order to prevent oxidation of the internal parts of the engine and of certain components in the injection system
36. ovable anode 16 Accelerator voltage divider lever 17 Sea water discharge plug 18 Auxiliary member pulley casing ENGINE TECHNICAL DATA N67 ENT M45 The technical code and serial number are indicated on a plate which is located on different parts of the engine according to the model flywheel casing tappet cover coolant tank Code Engine family Cycle Number and arrangement of cylinders Bore x stroke Total displacement Air system Injection type electronically Engine direction of rotation Dry weight Electrical system Accumulator s capacity discharge current N67 ENT M45 F4 4 stroke diesel 6 in line 102 x 120 mm 5 900 cm Supercharged aftercooled ICA or TAA Direct Common rail managed Anticlockwise seen from flywheel side 595 kg 12 V 24 V on request 180 Ah or above 800 A or above Available settings N67 ENT M45 1 331 kW 450 CV 3000 rpm A209 kW 420 CV 3000 rpm Bo 272W 370 3000 rpm 258 kW 350 CV 3000 rpm Net power to the flywheel in compliance with ISO 3046 1 Test conditions T 25 C atmospheric pressure 100 kPa relative humidity 30 WARNING Any alteration of the above mentioned characteristics in particular modification of the data stored in the injection system electronic units or the characteristics of the engine and its fittings is strictly prohibited penalty invalidation of the guarantee and absence of all liabilit
37. r pipe 10 Air filter 11 High pressure pump for common rail system 12 Fuel inlet from tank 13 Fuel outlet to tank 14 Fuel filter 15 Removable anode 16 Accelerator voltage divider lever 17 Sea water discharge plug 18 Auxiliary member pulley casing 04 364 N L O 2 Tm ENGINE TECHNICAL DATA N60 ENT M37 M40 The technical code and serial number are indicated on a plate which is located on different parts of the engine according to the model flywheel casing tappet cover coolant tank Code Engine family Cycle Number and arrangement of cylinders Bore x stroke Total displacement Air system Injection type electronically Engine direction of rotation Dry weight Electrical system Accumulator s capacity discharge current N60 ENT M37 M40 F4 4 stroke diesel 6 in line 102 x 120 mm 5 900 cm Supercharged aftercooled TCA or TAA Direct Common rail managed Anticlockwise seen from flywheel side 595 kg 12 V 24 V on request 180 Ah or above 800 A or above Available settings N60 ENT M37 A1 272 kW 370 CV 2800 rpm B 243 kW 330 CV 2800 rpm e 199 kW 270 CV 2800 rpm Available settings N60 ENT M40 A1 294 kW 400 CV 3000 rpm A2 272 kW 370 CV 3000 rpm B 243 kW 330 CV 3000 rpm C 199 kW 270 CV 3000 rpm Net power to the flywheel in compliance with ISO 3046 1 Test conditions T 25 C atmospheric pressure 100 kPa
38. rcumstances and the specific nature of operations required means that the intervention of a medical team is necessary 1 In the event of bleeding keep the edges of the wound pressed together until help arrives 2 f there is any suspicion of a fracture do not move the injured part and only move the patient if absolutely necessary 40 Caustic burns Caustic skin burns are caused by contact with extremely acid or alkaline substances For electric maintenance technicians these are typically caused by acid from batteries in these circumstances proceed as follows 1 Remove any clothing soaked in the caustic substance 2 Wash the area with lots of running water avoiding parts that have not been burned If either battery acid lubricants or diesel come into contact with the eyes wash the eyes with water for at least 20 minutes keeping the eyelids open so that the water flows over the eyeball move the eye in all directions to wash more thoroughly 35 30 25 20 15 10 5 0 5 10 15 20 25 30 35 40 45 50 20 _ an Eee L 2 Tm SAE10W 330 O SAE10W 00 10W 40 SAE 10W 60 SAE TSW A mineral SAE 15W 40 mineral base SAE 15W 40 SAE 15W 40 semisyntheticbase si SAE 15W 40 SAE 20W 60 semisynthetic base TT gt gt II SAE 5W 30 SAE 5W 30 synthetic base SAE 5W 30 s
39. the right to make modifications at any time without prior notice for technical or commercial reasons or to update the engines to comply with legal requirements in the various Countries The Manufacturer declines all liability for any errors or omissions Please remember that the IVECO MOTORS Technical Service Network is available to offer you its experience and professional skills wherever you may be L o 2 CONTENTS Page Page B GENERAL INFORMATION 0 00 nnne 3 B LONG PERIODS OF INACTIVITY 36 Pardee sas esas sues dunes elie Stead 3 Preparing the engine for a long period of inactivity 36 bocca UE 3 Restarting the engine after a long period of inactivity 3 B ENGINE MALFUNCTIONS 0 000 00008 38 E T eee 3 B EMERGENCIES ON 22 Ense technica dara INAO EDT M2 dig au seda tiara e x e te 4 B IINCAPPENDIX xt ewe ae GR e TE eR I Aoc x e de fee e e Enginetechnical data INOO 6 Oil viscosity level according to surrounding temperatures Engine technical data sss ote ico erate oa 8 DIC Cana E a eek LN hae 10 os eee ee beu uet er a ee 11 Pre IRIA ACEC RM dead EN 11 Starting and SLODDING te Spell eee ap acti t a RO Rr Ou 11 Starting and stopping the engine from
40. the used oil Unscrew the filter and remove it Carefully clean the surfaces of the support that are in contact with the filter seal Damp the new filter seal with a thin layer of oil Q Hand screw the new filter into place until the seal gasket touches the support then lock by a further 3 4 of a turn Dispose of the old filter according to current requirements L 2 O 2 Tm Changing the fuel filter Only proceed with the engine stopped and at a low temperature L Remove the filter by unscrewing it j L Check that the new filter has performance levels that satisfy the needs of the engine eg by comparing them with the old one See section on FREQUENCY Damp the new filter seal with diesel or engine oll L Hand screw the new filter into place until the seal gasket touches the support then lock by a further 3 4 of a turn 04 006 N Do not fill up the new filter before fitting it to the support to avoid introducing harmful impurities into the injection system and circuit CAUTION Do not attempt to bleed in any way as this is unnecessary and extremely dangerous and also if the high pressure circuit connectors are loosened there will be negative effects on start up of the engine 22 Changing the fuel pre filter Only proceed with the engine stopped and at a low temperature Remove the by unscrewing It Check that the new filter has performance levels
41. til the engine is stopped Alpha numeric display This provides the following information engine running speed e total running hours see note A exhaust gas temperature on request instant fuel consumption see note B The information required is selected by pressing the Scroll select button on both the control panels main and secondary 19 Detail of the main control panel 7 Alpha numenc display 9 Accessory function programming button 10 Button used to scroll through and select additional information 11 Button to reset the planned maintenance indicator 12 Button to disable the beeper A The control panel s internal electronics are programmed count the working hours and issue warnings when the time limit for ordinary maintenance operations expires this function requires that the counter be reset after each maintenance operation which is carried out from the main control panel as follows Pressing and holding the Prog 9 and Scroll select buttons 10 turn the key switch from position 8A to position 8B and wait for the display to show the pre set value e g 600 hours Release the buttons and press the Prog 9 button again once only to start the new count L 2 2 Tm If the set value does not correspond with the one foreseen for the type of oil being used see requirements in the sections on REFUELLING and FREQUENCY proceed as follows After displaying the
42. vessel from the bridge the only way to stop propeller thrust in the engine quickly is using the marine gear disengagement lever E EMERGENCIES ON BOARD The user of a vessel that has been constructed according to safety regulations when following the instructions provided in this manual and the indications given on the engine labels will be working in safe conditions Should improper conduct result in accidents always request the intervention of trained first aid specialists immediately In an emergency and while awaiting the arrival of first aid specialists follow the instructions given below Engine malfunctions When navigating with a malfunctioning engine take the greatest possible care when manouevering and make sure that all those aboard are holding firmly to safe hand holds see section on ENGINE MALFUNCTIONS In case of fire Extinguish the fire using the fire fighting equipment provided aboard and in the manner indicated by Fire prevention authorities the fire fighting equipment required on board is compulsory under current safety legislation Burns and scalds 1 Extinguish any flames on the burned person s clothing by throwing water over them using a powder fire extinguisher without directing the jet at the person s face covering with blankets or rolling the victim on the ground 2 Do not attempt to remove pieces of clothing that may have stuck to the skin 3 In the case of scalding immedi
43. when the engine is expected to be inoperative for periods of more than two months the following operations must be carried out in preparation for this 1 Drain the lubricant from the sump after first warming up the engine 2 Fill the engine with protective oil type 30 M or alternatively oil that complies with MIL 2160B type 2 specifications up to the minimum level indicated on the dipstick Start the engine and keep it running for approximately 5 minutes 3 Drain the fuel from the injection circuit from the filter and from the Injection pump pipes 4 Connect the fuel circuit to a tank containing CFB ISO 4113 protective fluid and feed in the fluid by putting the circuit under pressure and running the engine for approximately 2 minutes after first disabling the injection system This operation can be performed by polarising terminal 50 of the starter motor with a positive voltage equivalent to the rated voltage of the system using a conductor provided for that purpose 5 Nebulise approximately 60 g of 30 M protective oil 10 g per litre displacement into the turbocompressor suction inlet during the pressurised filling operation described in the previous point 6 Close all the suction delivery ventilation and bleeder openings in the engine with suitable plugs or seal them with adhesive tape 36 7 Drain the residual 30 M protective oil from the sump This oil can be used again for a further 2 preparation operations
44. y even if the required number of working hours are not reached 8 Only use filters with the following characteristics filtration level lt 12 um filtering efficiency D gt 200 WARNING When using fuel with a percentage sulphur exceeding 0 5 or when using oils that do not comply with the specifications provided in the refuelling table the times at which the engine oil engine oil filter and oil vapour filter must be changed will vary according to the use and working conditions of the engine itself for further information please consult the technicians responsible for maintenance L 2 2 T REQUIREMENTS Do not disconnect the batteries with the engine running Do not carry out arc welding operations in the vicinity of the engine without first removing electrical cables and electronic units After each maintenance operation involving disconnection of the battery batteries make sure that the terminals have been properly locked onto the poles 4 Do not use battery chargers to start the engine Disconnect the on board network battery batteries when recharging Do not paint the appliances components and electrical connectors equipping the engine 7 Disconnect the battery batteries before any electrical operations Contact the Boatyard before installing electronic equipment on board two way radios echo sounding equipment etc 28 HOW TO PROCEED Check oil
45. y on the part of IVECO MOTORS 9 000 OF C 2 I aa gt 04 352 N Engine NEF N67 ENT M45 1 Exhaust gas and sea water discharge 2 Turbocharger 3 Engine coolant sea water heat exchanger 4 Coolant outlet manifold from engine 5 Oil filter 6 Lifting U bolt 7 Coolant filler cap 8 Thermostat valve location 9 Alternator 10 Manifold connecting the cooling circuit to the coolant tank 11 Coolant infeed to engine 12 Water heater system tap or plug 13 Coolant discharge plug 14 Connection to battery positive terminal 15 Electrical starter motor 16 Removable anode 1 JB 3 5 6 8 YW w rit i MA N wA 4 XC an hino L O 2 Tm 7 6 Us 4 Engine NEF N67 ENT M45 1 Coolant expansion tank 2 Oil extraction pump 3 Oil filler cap 4 Oil dipstick 5 Common rail divider 6 Sea water pump inlet 7 Lifting U bolt 8 Oil vapour filter 9 Sea water circuit connector pipe 10 Air filter 11 High pressure pump for common rail system 12 Fuel inlet from tank 13 Fuel outlet to tank 14 Fuel filter 15 Removable anode 16 Accelerator voltage divider lever 17 Sea water discharge plug 18 Auxiliary member pulley casing SIGNS Certain warning signs are affixed to the engine and their meanings are indicated below NOTE The signs with an exclamation mark on them underline a potential danger Lifting po
46. ynthesis of organic substances and vegetable oils Biodiesel WARNING Refuelling from drums or tanks may result in pollution of the diesel fuel with the risk of damage to the injection system if necessary filter the fuel in a suitable manner or allow sedimentation of the impurities before refuelling Low temperature diesel EN 590 specifications distinguish different classes of diesel fuel identifying the characteristics of those best suited to low temperatures It is entirely up to the Oil companies to comply with these regulations which foresee that fuels suited to the climactic and geographic conditions of the various Countnes be distributed Filling up with marine gear oil For the amount and types of oil to be used in the marine gear please see the manual provided by the Manufacturer E CONTROLS AND MAINTENANCE MAINTENANCE PERSONNEL The engine control and maintenance operations described in the following chapter require training experience and compliance with current safety regulations for this reason they must be carried out by special technicians as indicated below Q Controls by workshop technicians or the vessel user if necessary Q Periodic maintenance by qualified personnel equipped with suitable equipment and adequate means of protection Operations marked by the key symbol see illustration Q Special maintenance by qualified personnel from Authorised Service Centres who have detailed technical in
47. ynthetic base SAE 0W 30 SAE OW 30syntheticbase SAE OW 30syntheticbase 31 22 13 4 5 14 23 32 41 50 59 68 77 86 95 104 113 122 F 41
Download Pdf Manuals
Related Search