Invacare 9000 Wheelchairs Wheelchair User Manual
Contents
1. AND VICE VERSA FIGURE 1 1 Pull the knob on the wheel lock block OUT 2 Rotate the wheel lock block to the horizontal or ver tical position as shown in FIGURE 1 3 Release the knob CLDs Built BEFORE 09 05 00 WHEEL LOCK Knob bi VERICALPOSIIION HORZONBLPOSTON CLDs Built AFTER 09 05 00 WHELLOCK Wheel BRAKE FIGURE 1 CONVERTING THE WHEELLOCK TO BRAKE AND VICE VERSA USING THE WHEEL LOCK FIGURE 2 The shiftlever MUSTbe in the neutral position be fore activating the wheel lock Failure to do so cancause accidental release ofthe wheel lock possibly resulting in injury ormake itmore diffic ult to disengage the wheel lock feature 1 Position the shift lever in the neutral position Refer to SHIFTING in PROCEDURE 1 of this manual 2 Ensure wheel lock block is in vertical position Refer to CONVERTING THE WHEEL LOCK TO BRAKE AND VICE VERSA in this procedure of the manual 3 Pullthe drive arm rearward until the wheel lock block engages with the rear tire 4 Pushor pull wheelchair to ensure rear wheel DOES NOT rotate with wheel lock engaged If rear wheel DOES rotate with wheel lock engaged perform the following steps HORZDNIALPOSION WHEEL LOCK BRAKE A Checkto make sure wheels are inflated to proper psi if applicable and perform 1 one of the following i lfwheels ARE inflated to proper psi proceed to STEP B ii If wheels ARE NOT inflated to proper psi inflate to pro2. KE CONVERTING WHEEL LOCK TO BRAKE AND VICE VERSA 6 USING THE W EEL Esq Wm Em 6 OSING THE BRAKE E 6 PROCEDURE 3 STEERING LINK CONNECTING REMOVING THE STEERING LINK TO FROM THE FORK 7 LIMITED WARRANTY SAFETY SUMMARY NOTE Refer to the 9000 wheelchair Owner s Manual Part Number 1056953 for additional safety information GENERAL WARNINGS The steering link must be removed from the fork for attendant operation Otherwise the attendant will be unable tp steerthe wheelchair properly The steering link mustbe connected to the fork when the CLD is in use Otherwise the userwill be unable lt to seer the wheelchair safely DO NOToperate the CLD on hills orinclines The weightlimitation forthe CLD is 250 Ibs lt Ir il MAINTENANCE NOTE Refer to the 9000 wheelchair Owner s Manual Part Number 1056953 for overall maintenance require ments EVERY THREE 3 MONTHS Place a drop of oil on all linkage points 3 in 1 oi or equivalent Inspect and tighten bolts if loosened Clean chrome components with a soft cloth ANNUALLY The CLD should be inspected by a qualified technician 2 gt 2 2 gt 2 3 in 1 oil Registered trademark of American Home Products Corporation 3 PROCEDURE 1 DRIVING This Procedure includes the following B NEUTRAL Allows for braking locking th
3. Owner s Operator and Maintenance Manual CLD CYCLICAL LEVER DRIVE 9000 WHEELCHAIRS DEALER THIS MANUAL MUST BE GIVEN TO THE USER OF THE CLD USER BEFORE USING THE CLD READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE SPECIAL NOTES DO NOTUSE THIS EQUIPMENTWATHOUTARST READING AND UNDERSIANDING THIS MANUALAND THE 9000 WHEELC HAIR OWNERS MANUAL PARTNUMBER 1056953 IF YOU ARE UNABLE TO UNDERSIAND THE WARNING S CAUTIONS AND INSTRUC TIONS CONTACTA HEALTHC ARE PROFESSIONAL DEALER OR TEC HNIC AL PERSONNEL IF APPLICABLE BEFORE ATTEMPTING TO USE THIS EQUIPMENT OTHERMWMSE INJ URY OR DAMAGE MAY RESULT SPECIAL NOTES WARNING CAUTION notices as used in this manual apply to hazards orunsafe practices which could resultin personal injury or property damage NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENTIS SUBJ ECTTO CHANGE WTHOUTNOTICE SAVE THESE INSTRUCTIONS 2 CONTENTS SAFETY SUMMARY MAINTENANCE TABLE OF CONTENTS SPECIAL NOTES SAFETY SUMMARY ie MAINTENANCE PROCEDURE 1 DRIVING N SHIFTING STEERING AND DRIVING bote aui Dou e fent Dn lepus 4 ADJUSTING DRIVE ARM HEIGHT 5 E ADJUSTING DRIVE ARM RELEASE LEVER AND OR BRACKET LEVER 5 N ADJUSTING DRIVE ARM TENSION 5 T S PROCEDURE 2 WHEEL LOCK BRA
4. UT THE SPECIHC CONSENTOF INVACARE ORTO A PRODUCTDAM AGED BY ES BEYOND INVACARES CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAROR FAILURE TO ADHERE TO THESE INSTRUCTIONS THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES IMPLIED WARRANTIES IF ANY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND HTNESS FOR A PARTICULAR PURPOSE SHALLNOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY PRO VIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN INVACARE SHALLNOTBE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH SIATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Corporation www invacare com USA Canada One Invacare Way 5970 Chedworth Way Invacare is a registered trademark of Invacare Corporation Elyria Ohio USA Mississauga Ontario 2000 Invacare Corporation 44036 2125 L5R 3T9 Canada 800 333 6900 905 890 8838 Form No 99 228 Part No 1087717 Rev C I 07 00
5. e Shifting Steering and Drivin wheels or attendant operation I d C REVERSE Allows the wheelchairto move rear Adjusting Drive Arm Height ward ONLY Adjusting Drive Arm Release Lever and or D Bracket Lever Steering R Adjusting Drive Arm Tension 1 Rotate the drive arm in the desired direction to steer l the wheelchair ME SHIFTING STEERING AND DRIVING Driving ME FIGURE 1 N 1 Place the shift lever in the desired position Refer to G Shifting SHIFTING in this procedure of the manual 1 Move the shift lever to one 1 of the following three 3 2 Push forward or pull rearward on the drive arm to positions DETAIL A move the wheelchair A FORWARD Allows the wheelchair to move for ward ONLY CLDs Built BEFORE 09 05 00 P Shift Lever Drive Arm DEWIL A PEIRAL Shift Lever CLDs Built AFTER 09 05 00 Shift Lever NEUTRAL FORWARD Shift Lever 4 DRIVING AD USTING DRIVE ARM HEIGHT FIGURE 2 1 Remove the button screw located on the drive arm 2 Lift up on the drive arm to expose the plunger tube 3 Align one 1 of the three 3 mounting holes in the plunger tube with the button screw mounting hole on the drive arm 4 Installthe button screw into the drive arm and plunger tube mounting hole to secure the drive arm to the plunger tube Tighten securely ADJ USTING DRIVE ARM RELEASE LEVER AND OR BRACKET LEVER FIGURE 2 NOTE Th
6. e drive arm release lever and or bracket lever can be rotated to keep it from protruding from the drive arm NOTE CLDs built AFTER 09 05 00 DO NOT have a drive arm release lever 1 Depress and hold the button on the release lever CLDs Built BEFORE 09 05 00 Drive Arm Mounting Hole Plunger Tube Drive Arm Release Lever V Wheel Lock Adjustment Hod PROCEDURE 1 2 Rotate the release lever to the desired position 3 Release the button ADJ USTING DRIVE ARM TENSION FIGURE 2 NOTE Adjusting the drive arm tension will increase re duce the amount of effort required to move the drive am 1 Turn the bracket lever COUNTERCLOCKWISE to loosen 2 Slidethe bracket up or down to adjust the amount of effort required to move the drive arm UP Increases the amount of effort required DOWN Decreases the amount of effort required NOTE It may be easier to pull up or push down on the wheel lock adjustment lever to move the bracket up or down 3 Turn the bracket lever CLOCKWISE to tighten Tighten securely CLDs Built AFTER 09 05 00 Button Screw Bracket Mounting Hole Lever CAN Wheel S Lock Adjustment Rod Button Bracket FIGURE 2 ADJ USTING DRIVE ARM HEIGHT Aoor m A 1IuU PROCEDURE 2 This procedure includes the following Converting Wheel Lock to Brake and Vice Versa Using the Wheel Lock Using the Brake CONVERTING WHEEL LOCK TO BRAKE
7. ght section of the fork the Fork spring by pushing the fork spring horizontally towards the fork CONNECTING REMOVING THE 2 Pull up on the steering pin to remove from the fork STEERING LINK TO FROM THE Steering Link FORK FIGURE 1 Hole oOoz xxmm o The steering link MUSTbe removed fiom the fork p forattendantoperation Otherwise the attendant tur will be unable to seer the wheekc hair properly Steering Pin The steering link MUSTbe connected to the fork REMOVED when the CLDisin use Otherwise the userwill be unable tp steer the wheelc hair safely 2 Fork Spring Connecting Straight Section 1 Compress and hold the straight section of the fork spring by pushing the fork spring horizontally towards the fork 2 Insert the steering pin into the hole in the fork NOTE It may be necessary to rotate the caster to align Fork the steering pin with the hole in the fork 3 Release the straight section of the fork spring 4 Ensure the spring has secured the steering pin in place by lifting up on the steering link FIGURE 1 CONNECTING REMOVING THE STEERING LINK TO FROM FORK LIMITED WARRANTY PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE PRODUCTS MANUFACTURED AFIER 4 1975 This wananty is extended only to the original haser user of our products This wananty gives you specific legal rights and you may also have
8. other legal rights which vary fiom sate ip slate Invacare warrantsits productip be free fiom defectsin materials and workmanship fora period ofone 1 yearfrom date of purc hase If within such warranty period any such productshall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy underthis waranty shall be limited to such repair and or replacement Forwaranty service please contactthe dealerfiom whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please wite directly to Invacare at the address below Provide dealer s name address the product model number date of purchase indi cate nature of the defect and if the product is serialized indicate the serial number Do not retum products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJ EC TED TO NEGLI GENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIHED WIH OUTINVACARESEXPRESSWRITIEN CONSENTINC LUDING BUTNOTLIMITED TO MODIRCATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATIACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENTWITHO
9. per psi and repeat STEP 4 B Contact a qualified dealer to adjust wheel lock CLDs Built AFTER 09 05 00 CLDs Built BEFORE Shift Lever Wheel n Lock Block NOTE Wheel lock block shown in vertical wheel lock position FIGURE 2 USING THE WHEELLOCK USING THE BRAKE USING THE BRAKE FIGURE 2 WARNING The brake should be tested ata dow speed in the presence ofan assistant Otherwise injury or damage may occur 1 Ensure wheel lock block is in horizontal position Refer to CONVERTING THE WHEEL LOCK TO BRAKE AND VICE VERSA in this procedure of the manual 2 Slowly begin driving the wheelchair Refer to DRIV ING STEERING AND SHIFTING in PROCEDURE 1 of this manual NOTE Continue steering the wheelchair as necessary while testing or using the brake 3 Pulldrive arm rearward until wheel lock block contacts rear tire and slows wheelchairto desired speed If brake DOES NOT make contact with reartire perform the following steps A Check to make sure wheels are inflated to proper psi if applicable and perform 1 one of the following i If wheels ARE inflated to proper psi pro ceed to STEP B ii If wheels ARE NOT inflated to proper psi inflate to proper psi and repeat STEPS 2 3 B Contact a qualified dealer to adjust brake STEERING LINK PROCEDURE 3 This procedure includes the following Removing Connecting Removing the Steering Link to from 1 Compress and hold the strai
Download Pdf Manuals
Related Search