Home

Indesit WD 12 X Washer/Dryer User Manual

1. Mount the magnetic plate on the opposite side at the top using the two type B screws Place the spacer illustrated in fig 4 B between the appliance front and the magnet receiver Using the Drilling Template To trace the positions of the holes on the left hand side of the panel align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference To trace the positions of the holes on the right hand side of the panel align the drilling template to the top right side of the panel Use an appropriately sized router to mill the holes for the two hinges the rubber plug and the magnet Mounding the Parts onto the Wooden Panel Door Insert the hinges into the holes the movable part of the hinge must be positioned facing away from the panel and fasten them with the 4 type A screws Insert the magnet into the top hole on the opposite side of the hinges and fasten it with the two type B screws Insert the rubber plug into the bottom hole The panel is now ready to be mounted onto the machine Fig 6 A C Vv Fig 7 Mounting the Panel into the machine Insert the nib of the hinge indicated by the arrow in fig 2 into the hole for the hinge and push the panel towards the front of the machine Fasten the two hinges with the type D screws Fastening the plinth guide If the machine is installed at the end of
2. then turn the washer dryer off by pressing on off button H O position Now you can open the appliance door Once you have removed the washing from the appliance leave the door open or ajar to avoid the formation of bad odours and turn off the water tap Dryingtime Min time Dryingtime Min A Fabric Load type Max load type kg Extra Wardrobe Iron dry Cotton Clothing of Linen different sizes Cotton Terry towels Acrylics Pyjamas socks etc Nylon Slips tights stockings etc The data contained in the table are purely indicative Terital Sheets Cotton Shirts 2 5 For cotton loads of less than 1 Kg use the drying programme designed for synthetic fabrics WARNING During the drying phase the door tends to get quite hot Do not use the appliance to dry clothes that have been washed with flammable solvents e g trichlorethylene Do not use the appliance to dry foam rubber or similar elastomers Make sure that the water tap is turned on during the drying cycles This washer dryer can only be used to dry clothes which have been pre washed in water Understanding labels Learn the meaning of these symbols and you will get better results your garments will last longer resulting in an improved wash Allover Europe garmentlabels These symbols are divided in contain messages expressedin five different categories and small yet important symbols shapes was
3. a set of modular cabinets mount either one or both of the guides for the base molding as shown in fig 8 Adjust them for depth based on the position of the base molding and if necessary fasten the base to the guides fig 9 This is how to assemble the plinth guide fig 8 Fasten angle P using screw R insert plinth guide Q into the special slot and once it is in the desired position lock it in place using angle P and screw R Inserting the machine into the Cabinet Push the machine into the opening aligning it with the cabinets fig 6 Regulate the adjustable feet to raise the machine to the appropriate height To adjust the position of the wooden panel in both the vertical and horizontal directions use the C and D screws as shown in fig 7 Important close the lower part of the appliance front by ensuring that the plinth rests against the floor 5 Accessories provided for the height adjustment The following can be found inside the polystyrene lid fig 10 2 crossbars G 1 strip M Fig 10 the following can be found inside the appliance drum 4 additional feet H 4 screws I 4 screws R 4 nuts L 2 plinth guides Q Adjusting the appliance height The height of the appliance can be adjusted from 815 mm to 835 mm by turning the 4 feet Should you require the appliance to be placed higher than the above height you need to use the fol
4. level the appliance the front feet must be adjusted the angle of inclination measured according to the worktop must not exceed 2 When placed on carpet make sure the ventilation is not reduced The front feet are adjustable Retain the transit screws spacers and washers Should you move house then these should be replaced to support the inside of the machine to prevent damage when transporting the machine 11 nstructions for installation and use Connection to the water mains Both hot and cold water supplies are preferable and they should be between 34 5kN m 5lb in and 1034 2kN m 150lb in pressure The hose having the red end fitting should be encountered between the hot supply and the threaded connection adjacentto the letter H on the rear of the machine The hose having the white end fittings should be connected between the cold supply and the threaded connection adjacentto the letter C on the rear of the machine Remember to insert a sealing washer at each connection to ensure watertight joints Do not overtighten the connections by using tools hand tight is sufficient to preventleaks Itis generally more convenient to have these supplies away from the sink taps Where no suitable hot water supply is available or it does not meet these requirements both inlet hoses may be connected to a cold supply by using two taps etc or a T junction on the plumbing however use of cold wa
5. not wash coloured linen with whites H Watch the weight For best results do not exceed the weight limits stated below figures show weight of dry garments Resistant fabrics 5 5 kg maximum Synthetic fabrics 2 5 kg maximum Delicate fabrics 2 kg maximum Pure new wool 1 kg maximum E How much does it weigh 1 sheet 400 500 gr 1 pillow case 150 200 gr 1 tablecloth 400 500 gr 1 bathrobe 900 1 200 gr 1 towel 150 250 gr E Coloured T shirts printed ones and shirts last longer if turned inside out before washing Printed T shirts and sweatshirts should always be ironed inside out H Dungaree alert Very popular salopette type overalls have straps with hooks that can damage the drum of your washer dryer or other garments during the wash To minimise the risk place hooks in the pocket and fasten with safety pins W Holidays unplug the appliance It is recommended that you should unplug the machine from the socket and turn off the water supply Leave the door ajar to allow air circulation to the draw and the door gasket area This will prevent unpleasant odours WOOL CYCLE For best results we recommend you use a specific detergent taking care not to wash more than 1 kg of laundry How to wash almost anything H Curtains Curtains tend to crease a great deal A useful tip to reduce creasing fold the curtains and place them in a pillow case or mesh bag Do not load
6. on the radio interference suppressor 4 Remove the screw and washer V fig 15 which act as astop for the cable passageway 5 Remove the upper part of the cable slightly from the back panel of the appliance pull the power supply cable upwards and take it out fig 16 To connect the new power supply cable reverse the pro cedure It is important for your safety that you reassemble all parts and screws used Instructions for installation and use 16 Stay in touch THANK YOU for choosing an Indesit appliance We are confident you have made a good choice and that your new appliance will give many years of excellent service And we re there when you need us Register your purchase how This will confirm your entitlement to enter our quarterly prize draw where you have the possibility to recover the cost of your purchase Simply complete and return the Registration Form supplied with the appliance documents using the FREEPOST envelope supplied Or call the Registration Hotline on 0870 010 4305 Ci invest a We re as close to you as your telephone For direct access to Genuine Indesit Spare Parts and Accessories call 0870 558 5850 and speak to our skilled staff who can help you to identify and purchase the item you require For a Rapid Response to a problem with your appliance call 0870 607 0805 We re open from Monday to Saturday 8am 5 30pm wee
7. persists call your local Indesit customer services who will be pleased to help Any failure will be repaired as soon as possible 1 1 e Technical characteristics p 10 Herein are the technical features of your washer dryer model type number electric and water specifications size capacity speed of the spin cycle and compliance with Italian and European regulations 12 Safety for you and your family p 16 Here you will find the necessary safety guidelines and it is important for you to read this section carefully 1 3 e Indesit stays with you after your purchase p 17 Indesit supports its products after their purchase by offering you a range of special services professional assistance spare parts and quality accessories What goes in your washer dryer Before washing you can do a great deal to ensure better results Divide your garments according to fabric and colour Read the labels follow their guidelines Before washing Divide your washing according to the type of fabric and colour fastness Empty all pockets coins paper money and small obejects and ensure all loose buttons are repaired or removed prior to loading Starting the washer dryer lt lt The labels say it all Always look at the labels they tell you everything about your garment and how to wash it in the best possible way The table on page 6 shows all meanings behind these symbols Their recom mendations are important to achi
8. 40 Volt 50 Hz maximum absorbed power 2050 W Water connections maximum pressure 1 MPa 10 bar minimum pressure 0 05 MPa 0 5 bar drum capacity 46 litre Spinning speed up to 1200 rpm Control programs wash programme 3 temperature 60C carried out with 5 kg load in compliance with drying run with a load of 2 5 kg and knob C et to position E IEC regulation 456 CE This appliance conforms with the following E E C directives 73 23 EEC of 19 02 73 Low Voltage and subsequent modifications 89 336 EEC of 03 05 89 Electromagnetic Compatibility and subsequent modifications Too much foam ls the detergent appropriate for machine washing Check whether the definition on its label reads for machine wash or hand and machine wash or any other similar wording ls the correct amount being used An excessive amount of detergent besides producing too much foam does not guarantee a more effective wash and causes scaling in the internal parts of the appliance The washer dryer does not dry E Check whether the plug has been correctly inserted into the socket there is electricity in your home the appliance door has been shut properly a delayed start if available has not been selected programme knob A has been set to position Stop Reset the drying cycle knob C has been set to position 0 The washer dryer doesn t dry properly E Check whether the end of the drain hose is
9. Never open the detergent dispenser while the appliance is functioning do not use hand wash detergent because the abundance of foam could damage its internal parts Filemone f Fp 8 Never pull on the supply cable or the washer dryer to disconnect it from the wall socket it is extremely dangerous 9 While the appliance is 10 functioning do not touch the drain water as it could reach very high tempera tures The appliance door during wash cycles tends to become hot ensure that children do no touch it Never force the washer dryer door because this could damage the safety lock which prevents accidental opening when the nachine is working Allow a few minutes at the end of the program for the lock to release In case of malfunctioning first close the water tap and unplug the appliance from the wall socket do not under any circum stances touch internal parts in order to attempt repairs The washing machine power supply cable is special and can be purchased exclusively from authorised Technical Service Centres To replace the cable 1 Make sure that the machine is switched off and unplugged 2 Remove the cover by unscrewing screws I fig 13 3 Disconnect the wires from the radio interference suppressor F fig 14 noting as to their position Blue N wire Brown L wire leaving the earth wire until last N B letters L N and the symbol are indicated
10. TA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacements can be obtained directly from your nearest Service Depot Warning The company denies all liability if and when these norms are not respected Plastic bags expanded styrofoam nails and other packaging parts are not children s toys and are potentially dangerous Removing the plug If your appliance has a non rewireable moulded plug and you should wish to re route the mains cable through partitions units etc please ensure that either the plug is replaced by a fused 13 ampere re wearable plug bearing the BSI mark of approval or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instructions for connecting cable to an alternative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neut
11. Washing machine Instructions for installation and use WD 12 X 1 inbesit Quick guide Here are the 13 topics explained in this manual Read learn and have fun you will discover many secret ways to get a better wash more easily and making your washer dryer last longer 1 Installation and removal p 11 Installation after delivery or transport is the most important operation for the correct functioning of your washer dryer Always check 1 That the electric system conforms to regulations 2 Thatthe inlet and draining pipes are connected correctly Never use pipes that have already been used 3 That the washer dryer is levelled properly something worth checking to aid the performance of your washer dryer 4 That the drum s fixing screws have been removed from the back of the washer dryer Di What goes in gou washer dryer and how to start it p 2 A correct distribution of your laundry is vital to the successful outcome of the wash and the life of the washer dryer Learn all the tips and secrets to dividing your linen colour type of fabric di Guide to understanding labels p 6 The symbols on the labels of your garments are easy to understand and equally important for the success of your wash The guide includes simple instructions to help you choose the right tempera ture wash cycles and ironing methods 4 Useful tips to avoid mistakes p 7 Years back our grandmothers were the ones who gave us good adv
12. anything else inside the appliance this will ensure that the overall weight does not exceed the half load Remember to use the specific programme 10 which automatically excludes the spin cycle 7 Instructions for installation and use H Quilted coats and anorak You can wash quilted coats and wind cheaters too if they are padded with goose or duck down Do not load more than 2 3 kg and never load 5 5 kg Repeat rinse once or twice using the gentle spin Wi Trainers Once you have removed mud and dirt from trainers you can even wash them with jeans or any other tough garments Do not wash trainers with whites opened by pull it outwards You must follow the dosage recommendations provided by the manufacturers when adding detergent or fabric conditioner Doses will vary according to the wash load the water hardness and how soiled the washing is Experience will help you select the right dosage almost automatically it will become your secret Before adding detergent for pre washing in compartment 1 make sure that the extra compartment for bleach 4 has not been inserted Ensure no overfilling when adding fabric conditioner in compartment 3 The washer dryer automatically adds the softener to the wash in each programme Liquid detergent is poured into compartment 2 just a few seconds before starting the wash cycle Remember that liquid detergent is only designed for wash cycles of up to 60 degr
13. e an automatic washing and drying cycle Follow the instructions for wash only see page 2 the paragraph entitled Starting the Washer Dryer and use knob C to set the type of drying cycle desired then press button H I position If the laundry load to be washed and dried exceeds the maximum load foreseen see table A then follow the instructions provided for wash only see page 2 the paragraph entitled Starting the Washer Dryer When the wash cycle has finished remove your washing divide it up and replace part of it inside the drum Now follow the instructions provided for a dry only cycle Repeat this procedure for the remainder of the load Iron lt 2 5 Instructions for installation and use IMPORTANT A spin cycle is carried out during the drying if you have set a cotton programme and a level of dryness Extra dry aes Wardrobe Dry only Once you have loaded the washing that needs drying 4 kg max for cottons see table for other fabrics make sure that the door is shut correctly the plug is inserted in the socket the water tap is turned on button H has not been pressed O position And now set the wash cycle knob Set knob A on the appropriate drying setting amp depending on the type of fabric select the type of drying cycle required using knob C and then press on off button H I position At the end of the drying cycle Wait for lamp I to flash slowly
14. ees on non pre wash items Special containers are sold with liquid or powder detergents for placing inside the washer dryer drum these are positioned according to the instructions found in the detergent box Never use hand wash detergent because it may form too much foam which could damage the washer dryer Detergents that are specifically formulated for both hand and machine wash are an exception One last secret when washing with cold water always reduce the amount of detergent you use it dissolves less easily in cold water than in hot water so part of it would be wasted The detergent dispenser can be removed and cleaned pull it outwards as indicated in the figure Then leave it under running water for a few minutes Cutting costs efficiently MAXIMISE THE LOAD SIZE Achieve the best use of energy water detergent and time by using the recommended maximum load size It s important for a good wash Useful tips about the detergent dispenser The first secret is the easiest the detergent dispenser is In compartment 1 Detergent for pre washing powder In compartment 2 Detergent for washing powder or liquid In compartment 3 Additives softeners perfumes etc In compartment 4 Bleach and delicate bleach Bleach cycle and stain removal button If bleaching is necessary the extra case 4 provided must be inserted into compartment 1 of the detergent dispenser When pouring i
15. eve better wash results After installing your new washer dryer start a wash cycle by setting programme 1 at 90 degrees Starting your washer dryer in the right way is important for the quality of your wash to help prevent future problems and enhance life expectancy of your appliance Once you have loaded your washer dryer and added the detergent together with any fabric conditioner always check that For more delicate garments protect underwear tights and stockings and delicate items by placing them in a canvas pouch 1 The door is closed correctly 2 The plug is secured in the socket 3 The water supply is turned on 4 Selector knob A is positioned on one of the symbols Stop Reset Choose the desired programme The programme is selected according to the type of garments that need to be washed To choose aprogramme refer to the table on page 4 Turn knob A until the selected programme is aligned with the mark on the knob turn knob B to the desired temperatu re settings check that knob C is in the desired position if necessary use buttons E F G and lastly press on off button H I position Big and small happily together This washer dryer has a special electronic control device for even distribution before the spin cycle starts this device allows the garments to positions themselves to minimise noise and vibrations during the spin cycle At the end of the wash cycle Lamp I w
16. hing xy bleaching Understanding them is very A ironing A dry cleaning O important if you want to get and drying GQ better results and treat your garments the way they deserve to be treated Useful tips Turn shirts inside out to get better results and make them last longer 7 Always empty pockets of their contents Look at the label it will always give you useful advice When loading your washing try to have a mixture of large to small items Make sure you select the right temperature Consult and learn the symbols in this table they will help you obtain a better wash treat your clothes properly and get a better performance out of your washer dryer ai Bleaching a Be cleaning Strong Delicate High Low action action Temp Temperat A Bleaching only in Hot iron at max Dry clean with any cold water 200 C solvent Machine dryable Dry clean only with Medium hot perchloride benzine ironing at av pure alcohol Do not machine Do not bleach max 150 C R111 and R113 dry A E Dry clean with av Iron at max benzine pure alcohol 110 C and R113 Spread to dry ZZX Q Hang to dry without spin Not ironable Do not dry clean drying Dry on clothes Hand wash hanger Not washable in water Instructions for installation and use 6 Useful tips W Never use your washer dryer to wash torn fraying or non hemmed linen If it is absolutely neccessary place it in abag for protection Do
17. ice and in those days synthetic fibres did not exist washing was easy Today your washer dryer offers you helpful advice allowing you to wash wool even better than an expert laundress would by hand 5 The detergent dispenser p 8 How to use the detergent dispenser and the bleach compartment 6 Understanding the control panel p 3 Washer dryer s control panel is very simple It has only a few essential buttons to help you choose any type of wash cycle ranging from the most energetic capable of cleaning a mechanic s overalls to the most delicate for wool Familiarising yourself with it will help you get the best out of your wash while helping your washer dryer last longer Its easy T Guide to the wash programmes p 4 Herein is an easy table to help you choose the right programme temperature detergents and possible additives Choose the right programme and you will get better results with your wash while saving time water and energy day after day 1 nstructions for installation and use 8 How to dry p 5 A few handy tips to get the best drying cycle from your appliance 9 Care and maintenance p 15 With just a bit of care it will repay you with loyalty and devotion With the necessary upkeep it will wash for years and years to come 10 Problems and solutions p 9 and 10 Before calling a technician read these pages immediate solutions may be found for a number of problems If the problem
18. ill flash quickly for a few seconds then it will begin flashing more slowly Then turn the washer dryer off by pressing on off button H O position You can now open the washer dryer door safely After having removed the freshly cleaned washing leave the door open to allow air circulation inside the drum Ink and biro Dab with a wad of cotton soaked in methyl alcohol or alcohol at 90 Tar Dab with fresh butter rub in turpentine then wash immediately Wax Scrape away then run a hot iron between two sheets of absorbent paper Then rub in cotton with turpentine or methyl alcohol Chewing gum Rub in nail polish remover and wipe with a clean rag Dividing your garments according to fabric and colour is very important for good results Always disconnect electricity at the socket and turn off the water supply Remember that in the event of a power failure or should the washer dryer switch itself off the programme chosen will remain in its memory Mold Cotton and white linen should be placed in a solution of 5 parts water one bleach and a spoon of vinegar then washed immediately For other white fabrics use hydrogen peroxide at 10 volumes and wash immediately Lipstick Dab with ether on wool or cotton Use tricloroetilene for silk Nail polish Place a sheet of absorbent paper on the side of the stain wet it with nail polish remover shifting the garment as the sheet gradually changes colour Grass Dab with a wad
19. in cycle Wash cycle at 50 C rinse cycles anti crease or delicate spin cycle Wash cycle at 40 C rinse cycles anti crease or delicate spin cycle Wash cycle at 30 C rinse cycles and delicate spin cycle Rinse cycles anti crease or delicate spin cycel Rinse cycles with automatic introduction of softener anti crease or delicate spin cycle Draining and delicate spin cycle Interrupts Cancels the selected programme Wash cycle at 40 C rinse cycles and delicate spin cycle Wash cycle at 30 C rinse cycles anti crease or draining Rinse cyclesi anti crease or draining Draining and delicate spin cycle Draining Interrupts Cancels the selected programme Important to cancel the wash programme you have just set select one of the symbols Stop Reset and wait for at least 5 seconds The data found in the table is purely indicative and can vary according to the quantity and type of washing the water system temperature and the room temperature By setting programme 8 at a temperature of 30 C you can wash different types of fabrics together except for wool and silk with a maximum load of 3 kg This programmes allows you to save on both time and energy as it only lasts around 30 minutes WE RECOMMEND THE USE LIQUID DETERGENT Instructions for installation and use 4 How to dry Acombined Washing and Drying Programme Look at table A to the side and follow the instructions provided for MAX load to hav
20. kdays 9am 5pm Saturday We have our own department of highly trained Indesit service staff For most calls our Service Engineer can fix the problem on the first visit Please have the following details to hand when you ring us The nature of the problem the Model Number and the Serial Number These numbers can be found on the appliance and on the portion of the Registration Card which you retain 17 Instructions for installation and use Instructions for installation and use 18 Merloni Elettrodomestici Viale Aristide Merloni 47 60044 Fabriano Italy Tel 39 0732 6611 Fax 39 0732 662501 www merloni com 1 InDesiT Leader for young Europe 02 2002 195033265 00 XEROX BUSINESS SERVICES DOCUTECH
21. lowing accessories to raise it to up to 870 mm the two crossbars G the 4 feet H the 4 screws I the 4 nuts L then perform the following operations fig 11 remove the 4 original feet place a crossbar G at the front of the appliance fastening it in place using screws I screwing them in where the original feet were then insert the new feet H Repeat the same operation at the back of the appliance Now adjust feet H to raise or lower the appliance from 835 mm to 870 mm Once you have reached the desired height lock nuts L onto crossbar G To adjust the appliance to a height between 870 mm and 900 mm you need to mount strip M adjusting feet H to the required height Insert the strip as follows loosen the three screws N situated at the front of the Top cover of the appliance insert strip M as shown in fig 12 then fasten screws N Instructions for installation and use 14 Easy Care and Maintenance Treat your machine well and it will provide many years of trouble free service Your washer dryer is a reliable companion in life and on the job It is just as important for you to keep it in shape Your washer dryer is designed to provide reliable service over many years A few simple steps will help to prolong its life and avoid problems It is advisable to turn off water taps when the machine is not to be used this protects the hoses etc If the water in your area is too hard u
22. n the bleach be careful not to exceed the max level indicated on the central pivot see illustration The use of the additional bleach container excludes the possibility of using the pre wash cycle Traditional bleach can only be used on sturdy white fabrics whereas delicate bleach can be used for coloured fabrics synthetics and for wool A guide to environmentally friendly and economic use of your appliance SAVE up to 50 energy by washing a full load instead of 2 half loads DO YOU NEED TO PRE WASH For heavily soiled laundry only SAVE detergent time water and between 5 to 15 energy consumption by NOT selecting Prewash for slight to normally soiled laundry IS A HOT WASH REQUIRED Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme SAVE up to 50 energy by using a 60 C wash programme BEFORE USING A DRYING PROGRAMME SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme You cannot bleach with the Silk programme and with the special programmes see page 4 Use the stain removal button every time you want to bleach Should you want to do it separately you must pour the bleach into the additional container 4 press button G stain removal start the washer dryer then select one of the symbols 29 according to the type of fab
23. ng the tap filter could be clogged with particles and debris ils the rubber hose kinked The tract of the rubber hose bringing water to washer dryer must be as straight as possible Make sure it is not squashed or kinked The programme selector knob keeps turning M Wait a few minutes for the drain pump to empty the tub switch the washer dryer off select one of the symbols stop reset then switch it back on If the knob continues to turn call for assistance because it is showing an anomaly The washer dryer continuously fills and drains water ils the drain hose positioned too low It must be installed at a height ranging from 60 to 100 cm M Is the end of the hose immersed in water M Does the wall drainage system have a breather pipe If the problem persists even after these checks turn the water supply off the machine and call for assistance If you live on an upper floor of your building there may be a problem with your drain trap To solve this problem a special valve must be installed The washer dryer does not drain or spin MDoes the selected programme incorporates water draining Some programmes stop at the end of the wash cycles and draining will have to be selected manually Mls the Easy iron function where provided enabled This function requires manual selection for draining Mls the drain hose kinked The tract of the drain hose must be as straight as po
24. of cotton soaked in methyl alcohol Instructions for installation and use 2 Here I m in command Making the right choice is important And it s easy Programme selector knob Use this knob to select the wash programme Turn this knob clockwise only To select a programme you should turn the knob so that the symbol number of the desired programme is in line with the pointer on the knob Now press on off button H position I pilot lamp I will start flashing After 5 the setting will be accepted pilot lamp I will stop flashing staying lit and the wash cycle will begin Should you wish to interrupt the programme in progress or set a new one select one of the symbols Stop Reset and wait 5 when the cancellation has been accepted pilot lamp flashes and you can then turn the appliance off After the wash cycle has been set and accepted by the washer dryer turning the knob will have no effect except for when itis on position Stop Reset ae The detergent dispenser with the additional bleach compartment is here 3 Instructions for installation and use Temperature control knob Itis used to set the wash tempe rature in the recommended programme table on pag 4 It also allows you to reduce the tempe rature recommended for the selected programme and even to set a cold wash cycle s amp Drying cycle knob Use this knob to select the desired drying cycle Two
25. options are available A Based on time From 40 minutes to 150 B Based on the damp level of the dry clothes Iron slightly damp clothes easy to iron Wardrobe dry clothes to put away Extra dry very dry clothes recommended for towelling and bathrobes A cooling stage is foreseen at the end of the drying cycle Detergent dispenser Itis divided into 3 compartments 1 Detergent for pre wash 2 Detergent for the main cycle wash 3 Fabric conditioner The washer dryer is equipped with an extra compartment 4 provided as an accessory for the bleach to be inserted in compartment 1 Easy iron This function allows your washing to come out of the machine without creases making it much easier to iron You can use it with programmes 3 4 Cotton 5 6 7 Synthetics and 9 10 Delicates Press this button in programmes 5 6 7 9 10 and the wash cycle will come to a stop on symbol amp y You can comple te it by pressing button E again Notes this function should not be used when button G stain removal has been pressed If you also want to run the drying cycle this button is enabled only if combined with level Iron Slow spin Use this button to reduce the spinning speed from 1200 to 600 rpm for the cotton and linen programmes and from 850 to 600 rpm for the synthetic fabrics programmes Stain removal see page 8 Thanks to this command the washer drye
26. our synthetics baby linen etc Delicate colour synthetics all types of slightly soiled garments Delicate colour synthetics all types of slightly soiled garments Rinse cycles bleach Fabric softener Spin cycle Drying cycle for synthetic fabrics Stop Reset DELICATES Wool hand wash Particularly delicate garments and fabrics curtains silk viscose etc Rinse cycles Spin cycle Draining Stop Reset Programme Temperature Detergent knob knob for wash nm 90 C 90 C 60 C vloleoile 2 3 4 40 C eS e 60 C 50 C 40 C vleoelole 30 C 5 6 7 8 3 2 9 40 C 10 30 C Fabric softener vloeololeoele 0 ee ee Stain rem button Bleach Del Trad Del Trad Del Trad Del Trad Delicate Delicate Delicate Delicate Length of the cycle minutes 165 145 130 95 100 95 70 30 60 50 Description of wash cycle Warm prewash wash cycle at 90 C rinse cycles intermediate and final spin cycles Wash cycle at 90 C rinse cycles intermediate and final spin cycles Wash cycle at 60 C rinse cycles intermediate and final spin cycles Wash cycle at 40 C rinse cycles intermediate and final spin cycles Rinse cycles intermediate and final spin cycles Draining and final spin cycle Interrupts Cancels the selected programme Wash cycle at 60 C rinse cycles anti crease or delicate sp
27. r will carry out a more intensive wash that optimises the effectiveness of the liquid additives thus allowing more resistant stains to be removed When you press the stain removal button you cannot activate the pre wash Understanding the control panel HHN i On off When button H is pressed the washer dryer is switched on when it is not the machine is switched off Turning the appliance off does not cancel the selected programme On off lamp door locked Lamp I flashes slowly when the appliance is switched on and awaiting instructions and at the endof a cycle indicating that the door can be opened It flashes quickly when the door should not be opened A steady light means the appliance has accepted the selected programme Drying cycle lamp When this lamp is on it means that knob C has been set on a drying cycle and at the end of the wash cycle the appliance will run the selected tumble drying cycle What are you washing today A programme for all seasons Type of fabric and degree of soil COTTON Exceptionally soiled whites sheets tablecloths etc Exceptionally soiled whites sheets tablecloths etc Heavily soiled whites and fast colours Slightly soiled whites and delicate colours shirts jumpers etc Rinse cycles bleach Spin cycle Drying cycle for cotton fabrics Stop Reset SYNTHETICS Heavily soiled fast colour synthetics baby linen etc Heavily soiled fast col
28. ral Brown Live As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E or or coloured Green or Green amp Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt the electrical supply to your machine consult a qualified electrician before use How to connect an alternati ve plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above GREEN amp YELLOW 4 BROWN 13 ampere fuse I Neng Ni BLUE lea 7 CORD GRIP Instructions for installation and use 12 Mounting the wooden panel onto the door and inserting the machine into cabinets In the case where the machine must be shipped for final installation after the wooden panel has been mounted we suggest leaving it in its original packaging The packaging was designed to make it possible to mount the wooden panel onto
29. rect position for those models concerned Mls the water supply turned on For safety reasons if the washer dryer does not load water it cannot start a wash cycle Leave the washer dryer plugged in while cleaning Even during maintenance the appliance should always be unplugged Use solvents and aggressive abrasives Never use solvents or abrasives to clean the external and rubber parts of the washer dryer Neglect the detergent dispenser It is removable and can easily be cleaned by leaving it under running water Go on holiday without thinking about her Before leaving always make sure that the washer dryer is unplugged and that the water supply is turned off But where did all the water go Simple with the new Indesit technology you need less than half of it to get good results on twice as much This is why you cannot see the water through the door because there is little very little of it to respect the environment yet without renouncing maximum cleanliness And on top of that you are also saving electricity The washer dryer fails to fill with water ils the hose correctly connected to the tap ils there a water shortage There could be work in progress in your building or street Mls there sufficient water pressure The autoclave may be malfunctioning ils the tap filter clean If the water is very calcareous or if work has recently been carried out on the water pipi
30. ric When you bleach during a normal wash cycle pour the detergent and any additives in the special compartments press button G stain removal set the programme you desire and turn the washer dryer on Instructions for installation and use 8 Troubleshooting Before calling read the following In most cases when your washer dryer fails to work the problems arising can be easily solved without having to call for a technician Before calling for assistance always check these points The washer dryer fails to start Ms the plug correctly inserted into the socket It could have been moved whilst cleaning Mls there electricity in the house A circuit breaker may have switched off as a result of too many electrical appliances working at the same time Or maybe due to a general failure in your entire area Mls the washer dryer door closed properly For safety reasons the washer dryer cannot work if Turn off the water supply after use This will eliminate the possibility of leakage Always leave the appliance door ajar to avoid bad odours Clean the appliance s exteriors gently To clean the exteriors and the rubber parts of the appliance always use a soft cloth dipped in warm and soapy water 9 Instructions for installation and use the door is open or not shut properly Mis the On Off button pressed If itis then a programmed start has been set Mis the programmed start knob in the cor
31. se a deliming product water is hard if it often leaves whitish stains around taps or drains especially of bath tubs For more accurate information as to the type of water in your system call the local water works or a local plumber Pockets must always be emptied removing even pins badges and any other hard object The washer dryer exterior should be cleaned with a rag dipped in lukewarm water and soap It is important to wash the detergent dispenser regularly To prevent dried washing powder from accumulating place the dispenser under running water for a few minutes Never exaggerate with doses Normal detergents already contain deliming agents Only if the water is particularly hard that is rich in lime content do we recommend the use of a specific product at every wash A periodical wash cycle with a dose of a deliming product without detergents or washing may prove useful Never use too much detergent or additives because this could cause an excess amount of foam scaling and possible damage to the component parts of your washer dryer Do not forget to empty all pockets small objects can cause damage to your washer dryer The washer dryer comes equipped with a self cleaning pump that does not require any cleaning or maintenance The water inlet hose Check the rubber hose at least once a year If you see any cracks replace it immediately When you use your washer dryer water pressure is very s
32. ssible Make sure the drain hose is not squashed or kinked Always get assistance from authorised technicians and always insist on original spare parts Technical characteristics Dimensions Mis the washer dryer s drain duct clogged Is there an extension of the drain hose If so is it positioned incorrectly blocking the water flow Excessive vibration during the spin cycle E Have all transit screws been removed durind instal lation See the following page on installation procedures E Has the washer dryer been levelled correctly The levelling of the appliance should be checked periodically Adjust the feet and check them with a level width 59 5 cm height 81 5 cm depth 54 cm Mls there space between the machine and adjacent units If it is not a built in model the washer dryer will oscillate a bit during the spin cycle A few cm of space should therefore be left around it The washer dryer leaks Mis the metal ring of the inlet hose properly attached Turn off the water supply unplug the appliance and try tightening its attachment without forcing it Mls the detergent dispenser obstructed Remove and wash it under tap water Mis the drain hose well attached Turn off the water supply unplug the appliance and try tightening its attachment Capacity from 1 to 5 5 kg for the wash programme from 1 to 4 kg for the drying programme Electrical connections voltage 230 2
33. ter only will increase programme times Note the maximum temperature should not exceed 70 C 158 F The rubber gasket Connect the inlet hose to the threaded connector on the machine rear Water pipe inlet at the top right Connecting the drain hose The drain hose hooked pipe is secured to the rear of the machine by support clips and may be routed to right or left as required The hook to be used in case the drain hose ends at a height below 60 cm The drain hose should be placed in a stand pipe with a minimum internal diameter of 38 mm 1 inches or it can be positioned over a sink or it can be connected as shown in Fig A The height of stand pipe or sink should be between 60 and 100 cm 24 and 40 inches Care must be taken that the hose is not obstructed twisted submerged or kinked If the hose is connected with an airtight joining provision should be made to prevent syphoning The guide for draining into tubs and sinks AIN il Electric connection Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp AS
34. the machine without removing it completely see figures below heria r 1 lavabiancherla H i hine J i hing mac i wash faver L i su J avabiancher a Washing machine y machine laver 13 nstructions for installation and use Instructions for the fitter The wooden panel that covers the face of the machine must not be less than 18 mm in thickness and can be hinged on either the right or left For the sake of practicality when using the machine we recommend that the panel be hinged on the same side as the door for the machine itself the left Door Mounting Accessories Fig 1 2 3 4 5 N 2 Hinge Supports N 2 Hinges Fig 1 Fig 2 A N 1 Magnet N 1 Magnet plate Fig 3 Fig 4 N 1 Rubber plug N 1 Spacer i Fig 5 No 6 type A self threading screws 13 mm No 2 type B metric countersunk screws 25 for fastening the magnet plate to the cabinet No 4 type C metric screws 15 mm for mounting the hinge supports to the cabinet No 4 type D metric screws 1 7 mm for mounting the hinges on the supports Fig 4 B Mounting the Parts onto the Face of the Machine Mount the hinge supports onto the face of the machine positioning the hole indicated by the arrow in fig 1 towards the inside of the face and using the type C screws
35. trong and a cracked tube could easily split open 15 Instructions for installation and use Important for the safe use of your washer dryer Your safety and that of your family Read these instructions and all the information in this manual carefully they are an important source not only of numerous useful tips but also of vital information on safety use and maintenance 1 the machine should not be installed in an outdoor environment not even when a roof shelters the area because it may be very dangerous to leave it exposed to rain and thunderstorms 2 It must only be used by adults and exclusively for washing clothes following the instructions provided in this manual 3 Should it have to be moved proceed with the help of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy 4 Before loading the washer dryer make sure the drum is empty hano How 5 Never touch the washer dryer when barefoot or with wet or damp hands or feet Never use extensions or multiple plugs which are particularly dangerous in humid environments The power supply cable must never be bent or dangerously compressed Tonly want an authorised specialised technician with original Indesit spare parts Your washer dryer has been built in compliance with the strictest international safety regulations To protect you and all your family 7
36. underwater the drain pump is obstructed the advice given on the maximum loads has been taken the water tap has been turned on If despite all checks the washer dryer fails to function and the problem persists call your nearest authorised Customer Service Centre providing the following information the nature of malfunction the model type no Mod the serial number S N This information can be found on the data plate situated at the back of the washer dryer Instructions for installation and use 10 Installation and removal When the new washer dryer arrives Whether new or just transported to a new house installation is extremely important for the correct functioning of your washer dryer After removing the appliance from its packaging check that it is intact If in doubt contact a qualified technician immediately The inside of the machine is supported for transportation by four screws on the back panel Before using the washing machine remove the screws remove the spacers together with the rubber tubes attached to them keeping all the parts and use the plastic plugs provided to fill in the holes Important Use the cap provided to close the 3 holes which housed the stop pin situated in the right hand part of the lower back of the washing machine Levelling The washing machine must be levelled appropriatey in order to guarantee its correct functioning To

Indesit WD 12 X Washer/Dryer User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents