Icom DS-100 Network Card User Manual
Contents
1. Front panel DISTRESS BUTTON Push and hold for 5 sec to make a distress call CLEAR SWITCH CLR Push this key to cancel Call repeat Push this key to cancel the menu CALL SWITCH CALL PANEL DESCRIPTION Push this key to call subject menu screen Push the key to return the start screen Q ENTER ENT 1 Enters the selected subject and advances the item to in dicate the contents Push this key to determine the data UP DOWN LEFT RIGHT SWITCHES AV V 4 Push A W to select the menu contents in the selected item Push to adjust brightness and contrast Push lt 4 gt to move the cursor position Q KEYPAD Input the corresponding number or letters when re quired Other functions are as follows A a Push this key to toggle the capital letter small letter or numerals A capital letter or a small letter appears in the upper right of the display depending on selection BS Backspace key Q FUNCTION DISPLAY During normal operation the display shows position and UTC or Local time when a GPS receiver is connected This is updated each time new GPS data is received If no GPS receiver is connected the position and UTC time 1 PANEL DESCRIPTION must be set in advance NOTE If GPS2. D Confirm any distress call is not being received Lift up the switch cover pushing and holding the Nature of distress DISTRESS button for 5 Undesi gnated sec to transmit the distress GPS UTC 15 22 call 12 34 N 123 45 W A DSC channel ch 70 is auto matically selected and the dis tress call is transmitted e If you have the time select the nature of the distress and con tents If no GPS is connected your location and UTC time should be input C Push and hold DI STRESS for 5 sec CALLPROCEDURE 2 3 After transmitting the call the transceiver is set to the phone frequency ch 16 au tomatically 4 gt The controller is still waiting on Compl eted ch 70 for an acknowledgment call Now waiting for When receiving the acknowl acknowl edgemt edgment reply to the con nected station via the CLRoExi t transceiver s microphone as J described on the page at right NOTE Distress alert simple operation contains default Kinds of distress Undesignated distress Position data According to the displayed information GPS or manual input position data held for 23 5 hrs Distress call repeats every 3 5 4 5 min until receiving an ac knowledgement Beep Pi Pi sounds with the max volume every 1 sec Push DISTRESS button to transmit a renewed distress call if de sired Push CLR to cancel the Call repeat mode The
3. 7 3 WHEN RECEIVING A CALL 9 17 To receive a DSC call 9 When receive a distress call 10 Received message 13 4 SETUP caet ce terere pietre 17 19 Select Set up 17 IBI Address ID ntt tt ttc ef 17 Offset time rien tn rete 19 B Brightness n Re nee 19 Bi Contrast UC 19 BIMMSI clieck aii eese 19 5 CONNECTIONS AND INSTALLATIONS 20 22 Connection diagram 20 Rear panel description 21 Supplied accessories 21 Bi Mounting ieu e 22 6 VHF MARINE CHANNEL LIST 23 7 SPECIFICATIONS AND OPTIONS 24 Specifications 24 Options rentre cre e eet 24 8 DIMENSIONS occorre tance ate cornice rutru 25 9 MB 75 OPTION 26 27 75 FLUSH MOUNT 26 TEMPLATE DSC CONTROLLER DS 100 Ye WATER RESISTANT AWE gt
4. Group call D Push CALL then push V one or more times to select Group call then push ENT Select the desired address then push ENT Enter the 8 digit address when Manual entry is selected Push CALL and ENT si M Select a group Manual COM entry lt CLRDExit ENTOK gt multaneously to transmit a Group call Push CLR to stop the call lt input an address gt ID 8di git 0 lt CLRDExit ENTSOK gt CALL PROCEDURE 2 Bi All ships call D Push CALL then push V one or more times to select ships call then push ENT 2 Select the desired category then push ENT 3 Push CALL and ENT si multaneously to transmit an All ships call 4 Push CLR to stop the call lt Select category gt Safety PUrgency lt CLRDExit ENTOK gt M 2 PROCEDURE When no acknowledgement is received If no acknowledgement is received the emergency alarm will sound continuously In this case the controller automatically tramsmits the distress call again every 3 5 to 4 5 minutes Push CLR if you want to stop the alarm A distress relay call may be received after several min utes from another ship if acknowledgement cannot be re ceived from a coast station directly ZZ CAUTION DO NOT push CLR while waiting for an ac knowledgement otherwise the distress cal
5. stress relay om DS 100 SN3 istress 0 2345678 To all ships Fire Explosion Distress Time amp Pos T P i me UTC 12 34 os Lat 12 34 N Lon 123 45 W lt A a gt Dataclear gt 15 16 WHEN RECEIVING A CALL Distress relay acknowledgement D Push CALL then push V several times to select Re ceived calls then push ENT 2 Select Other message then push ENT 3 Select Distress RLY then push ENT e Push A V to scroll the message Push A a to clear the mes sage C Select a message ndividual ACK ndividual cal Group cal ALL ships call Distress Distress relay 7 Distress RLY ACK istress ACK W oc co amp c A e r RDExit gt 0 gt J lt Message contents gt Distress RLY ACK From Mr Comort Distress ID Mrs John Fire Explosion Distress Time amp Pos Ti me UTC 12 34 Pos Lat 12 34 N Lon 123 45 W clear L D Distress acknowledgement D Push CALL then push V several times to select Re ceived calls then push ENT 2 Select Other message then push ENT 3 Select Distress then push ENT Push A or W to scroll the message Push A a to clear the mes sage wn e ect a message ndividual ACK ndividual
6. Push ENT to transmit your own ships longitude and lat itude information Push CLR to record the received information then the screen goes back to de fault RCV Pos request From J HON To reply push ENT CLRoExi t ENT 0K o When receiving a Postion reply When receiving a Position reply an alarm Pi pi sounds Push CLR to record the received information then the screen goes back to de fault RCV Pos reply From Beck Pos Lat 12 34 N Lon 123 45 W CLRoExit 11 12 WHEN RECEIVING A CALL When receiving a Distress ACK When receiving a distress ac knowledgement an alarm Pi po sounds with max AF level continuously And at the same time the transceiver s IC M501EURO operating channel changes to CH 16 automati cally Push CLR to cancel the alarm Va RCV Distress From Tokyo guard Distress ID Mr Bean CLRoExi t ENT 0K When receiving a Distress Relay ACK When receiving a Distress Relay acknowledement an alarm Pi po sounds with max AF level continuously And at the same time the transceiver s IC M501EURO operating channel changes to CH 16 au tomatically Push CLR to cancel the alarm RCV Distress RLY From Tokyo guard Distress 0 987654321 CLRoExi t ENT 0K o When receiving a group call When receiving a Group call an ala
7. ICOM INSTRUCTION MANUAL DSC CONTROLLER DS 100 Icom Inc FOREWORD FEATURES Thank you for purchasing this Icom product The DS 100 DSC CONTROLLER is designed and built with Icom s superior tech nology and craftsmanship With proper care this product should provide you with years of trouble free operation IMPORTANT READ ALL INSTRUCTIONS carefully and com pletely before using the controller SAVE THIS INSTRUCTION MANUAL in struction manual contains important operating instructions for the DS 100 EXPLICIT DEFINITIONS WORD DEFINITION Personal injury fire hazard or electric AWARNING shock may occur CAUTION Equipment damage may occur NOTE If disregarded inconvenience only No risk of personal injury fire or electric shock US Class D DSC terminal The DS 100 VHF DSC CONTROLLER is designed as a Class D DSC terminal unit for the IC M501EURO VHF MARINE TRANSCEIVER ES Self ID indication The DS 100 does not function when there is no ID is pro grammed Therefore the ID code should be checked in the Set up menu INSTALLATION NOTES In all cases any possible risk of injury depends on the trans mitter being activated for long periods actual recommenda tion limits are specified as an average of 6 minutes Normally the transmitter is not active for long periods of time Some radio licences will require that a timer circuit automaticall
8. RCV Individual 1 From JHON CLRoExi t ENT 0K gt When the individual ACK function is available When the individual acknowledgement function is available on your controller push ENT to turn to the Select to com ply screen Select Able to comply or Unable to comply Emergency alarm or con tinuous beeps depending on the category sounds until pushing CLR Individual acknowledgement function Please ask your dealer for details V Select to compl y gt Able to comply Unable to comp y CLRoExi t ENT 0K When receiving an All ships call When receiving a Routine or Safety all ships call an alarm Pi pi sounds When you receive a distress or Urgency all ships call an alarm Pi po sounds with max AF level continuously Push CLR to cancel the alarm Push ENT then the oper RCV All ships call From 23456789 Category Routine CLRoExi t ENT 0K B ating channel changes to received traffic channel auto matically Push CLR to record the received information then the screen goes back to default You must monitor the traffic frequency until you can judge from the call that your action has been effective and or assis tance is unnecessary WHEN RECEIVE ACALL 3 When receiving a Position request When receiving a Position re quest call an alarm Pi pi sounds
9. D D istress RLY istress ACK lt CLRDExit ENTOK gt 27 lt Message contents gt Routine to group From Phil Collins F3E G3E simplex CH78 No information All ships D Push CALL then push V several times to select Re ceived calls then push ENT Select Other message then push ENT G Select All ships call then push ENT Push A or W to scroll the message M Message contents Urgency to AI From DS 100 SN3 F3E G3E si mpl ex CH 14 shi ps lt clear Ne Push A a to clear the message Distress D Push CALL then push V several times to select Re ceived calls then push ENT 2 Select Other message then push ENT 3 Select Distress then push ENT Push A or W to scroll the message Push A a to clear the mes sage M Message contents Routine to group From DS 100 SN3 F3E G3E Si mpl ex CH88 No Information lt Data clear WHEN RECEIVING A CALL Distress relay D Push CALL then push V several times to select Re ceived calls then push ENT 2 Select Other message then push ENT 3 Select Distress relay then push ENT Push A or W to scroll the message Push A a to clear the mes sage M Message contents
10. body against the inside of the in strument control panel MB 75 9 4 Tighten the end bolts on clamps rotate clockwise so that the clamps press firmly ER 8 9 5 Tighten the locking nuts ro tate counterclockwise so that the DS 100 is securely mounted in position as below 6 Connect the antenna and con trol cable then return the in strument control panel to it s original place 27 164 615 35 TEMPLATE 149 57 8 4 R11 7 6 Unit gt gt 92 35 5 16 5 8 mm inch DECLARATION ICOM OF CONFORMITY We Icom Inc Japan 6 9 16 Kamihigashi Hirano ku Osaka 547 0002 Japan Declare on our sole responsability that this equipment complies the essential requirements of the Radio and Telecommunications Terminal Equipment Directive 1999 5 CE and that any applicable Essential Test Suite measurements have been performed Kind of equipment DSC CONTROLLER Type designation D S Version where applicable This compliances is based on conformity with the following harmonised standards specifications or documents i EN 301 025 2 0 1 2 2000 02 ii EN 60945 1997 300 698 December 1996 iv C 0560 D D sseldorf 10th Apr 2000 Place and date of issue Icom Europe GmbH Himmelgeister stra e 100 D 40225 D sseldorf Authorized representative name Icom
11. cancel acknowledgement is automatically transmitted when the CLR key is pushed 2 PROCEDURE Distress call Regular operation Transmit a distress call after selecting the Distress setting NEVER USE THE DISTRESS CALL WHEN YOUR SHIP IS NOT IN AN EMERGENCY DIS TRESS CALL CAN BE USED ONLY WHEN IM Z MEDIATE HELP IS NEEDED D Push CALL then push V f several times to select Dis Select a subject tress setting Push ENT to select lt Select a nature Push V several times to select the desired nature then push ENT Push CLR to Exit the menu 3 Confirm the location data then push ENT to confirm the time data 4 Confirm the UTC time then push ENT to confirm the time data If no GPS is connected your location and UTC time should be input Entry position ti me Individual call Group call All ships call Recei ved calls PDistress setting Lift up the DISTRESS switch cover pushing and holding the button for 5 sec to trans mit the distress call 2 A DSC channel ch 70 is auto matically selected and the dis Select a nature Undesignated tress call is transmitted Fire Explosion If no GPS is connected your lo Flooding cation and UTC time should be Collision Grounding input Capsizing 6 After transmitting the call the 5 transceiver is set to the Disable adrif
12. Europe GmbH gt 7 T Aoki General Manager Signature Icom Inc Count on us lt Intended Country of Use gt GER B NED B ITA AUT E BEL GRE GBR ELUX B SWE MESP DEN E POR B FIN A 5654H 1EU Icom Inc Printed in Japan pus z 2000 Icom Inc 6 9 16 Kamihigashi Hirano ku Osaka 547 0002 Japan
13. data lt A aDNull data Enter the longitude data with lt CLRDExit ENTSOK gt key pad d 5 Push to select E east longitude or W west lt input Ti me longitude then push ENT Push lt 4 gt to move the cur UTC sor then push A V to correct the data Push CLR to Exit the menu lt a2Null data Push A a the push ENT to lt CLRDExit ENTOK gt enter a Null data 2220 2 PROCEDURE 6 Push UTC time with keypad Push 4 F to move the cursor then push to correct the data Push CLR to Exit the menu Push A a then push ENT to enter Null data Distress call to ships General DSC call with the distress category may be used for communications after the Distress call e g you want to change the operating mode frequency etc B individual call D Push CALL then push V several times to select Indi vidual call then push ENT 2 Push V several times to se lect the desired address then push ENT Enter the 9 digit ID when Man ual entry is selected Push CLR to exit the menu Push CALL and ENT si multaneously to transmit an Individual call 4 Push CLR to stop the call Select an address Manual entry DS 100 SN10 DS100 SM2 DS100 SN3 CLROExit ENTOK gt Va Input an address gt D 9di gi t CLROExit
14. 0 161 750 64 156 225 160 825 74 156 725 156 725 86 157 325 161 925 04 156 200 160 800 14 156 700 156 700 24 157 200 161 800 65 156 275 160 875 77 156 875 156 875 87 157 375 161 975 05 156 250 160 850 15 156 750 156 750 25 157 250 161 850 66 156 325 160 925 78 156 925 161 525 88 157 425 162 025 06 156 300 156 300 16 156 800 156 800 26 157 300 161 900 67 156 375 156 375 79 156 975 161 575 07 08 156 350 156 400 160 950 156 400 17 18 156 850 156 900 156 850 161 500 27 28 157 350 157 400 161 950 162 000 68 69 156 425 156 475 156 425 156 475 80 81 157 025 157 075 161 625 161 675 09 156 450 156 450 19 156 950 161 550 60 156 025 160 625 70 156 525 156 525 82 157 125 161 725 10 156 500 156 500 20 157 000 161 600 61 156 075 160 675 71 156 575 156 575 83 157 175 161 775 23 EE SPECIFICATIONS AND OPTIONS Specifications Options General MB 75 FLUSH MOUNTER Operating frequency 156 525 MHz For mounting the DS 100 to a panel Available in black or Mode 16K0G2B white Operating temperature range 20 C to 60 4 F to 140 F CS DS100 CLONING SOFTWAR
15. E Dimensions 165 W x 110 H x 80 D mm OPC 478 CLONING CABLE projections not included 6 5 W x 4 33 H x 3 15 D in Allows quick and simple setting of vessel name call sign ID Weight 1 Kg 2 2 Ib etc from a PC Receive system Double conversion superheterodyne Intermediate frequencies 1151 21 70 2 2nd 450 kHz Sensitivity 10 typ Intermodulation rejection ratio More than 68 dB Adjacent channel selectivity More than 73 dB Spurious response rejection ratio More than 73 dB Measurement methods according to EN 301 025 24 RN DIMENSIONS OM OW 110 0 ZO 31 4 53 0 25 0 145 0 84 4 Unit 25 mum 9 MB 75 FLUSH MOUNT KIT MB 75 OPTION The MB 75 is used to mount the DS 100 DSC CON TROLLER flush to a flat surface such as an instrument panel Supplied accessories CIAMPS Mi Eds 1 sets 26 Instructions Using the template p 29 carefully cut a hole into the in strument panel or wherever you plan to mount the con troller 2 Slide the controller through the hole rear panel first 3 Using the 2 supplied bolts M5 x 8 mm attach the clamps on either side of the DS 100 as shown below Make sure that the clamps align parallel to the DS 100 s
16. NA CONNECTOR Connects a marine VHF receiving antenna with a PL 259 plug for emergency frequency signal receiving Receiving frequency 156 525 MHz Keep the emergency frequency signal receiving antenn away from the marine VHF antenna to avoid interference from the emitted RF signal CLONE RECEPTACLE For dealer use only GPS RECEIVER CONNECTOR Connects a GPS receiver NMEA0183 ver 2 0 for sending position data without manual input ANTENNA CONNECTOR IC M501EURO Connects a marine VHF antenna with a PL 259 connector to the transceiver Q EXTERNAL SPEAKER RECEPTACLE IC M501EURO Connects to an external speaker DC POWER CONNECTOR IC M501EURO Connects the DC power cable supplied with IC M501EURO from this connector to an external 12 V DC power source CONNECTION AND INSTALLATIONS 5 Refer to the IC M501EURO instruction manual Supplied accessories D Nob bolt 2040 knob bolt 2 2 Mounting bracket 2345 Mobile bracket 1 3 Spring washers M 5 2 4 Self tapping screws A05 x 20 2 Flat washers M 5 2 Label 2349 CAUTION 1 21 22 D CONNECTION AND INSTALLATIONS Mounting The universal mounting bracket suppli
17. cal oup cal ships call istress istress relay istress RLY ACK 8 Distress ACK Woo c es lt CLRDExit ENTOK gt J Va lt Message contents gt Distress ACK From Fortune Distress ID Mrs John Fire Explosion Distress Time amp Pos Ti me UTC 12 34 Pos Lat 12 34 N Lon 123 45 W lt a gt Dataclear gt SET UP ANN Select Set up Address ID The following setting operations available in Set up menu Address ID Offset time Brightness Contrast MMSI check D Push CALL then push V several times to select Set up then push ENT Select Set up then push ENT Set up menu appears on the screen Push CLR to exit the Set up menu Select a subject Indi vi dual ACK Group call All ships cal Received calls Distress setting Set up N lt Select a subject gt gt Address 1 Offset time Brightness Contrast MMSI CHECK lt CLR Exit ENT gt 0K gt M A total of 70 address ID can be programmed as Address ID for ships and coast stations and Group ID for group sta tion f gt Add an address ID Select a subject D Push several times to select Add an address ID then push ENT 2 Push numeral keys to input an address ID code then push ENT When a wrong number is input push CLR then correct
18. data is interrupted for 30 sec the GPS indi cation disappears The terminal unit retains the most recent data in such cases Function display Q GPS INDICATOR GPS appears while GPS receiver is connected GPS disappears when no GPS receiver is connected MNL appears when the time data and position data are input manually TIME ZONE INDICATOR Local appears when the offset time data on the Set up menu is entered No time data appears when no GPS receiver is con nected and no time data is input manually POSITION INDICATOR Shows the GPS position data 22 may blinks every 2 sec instead of position data when the GPS position data is invalid In such a case the last position data is held up to 23 5 hours Shows the manually input position data when GPS re ceiver is connected MNL appears instead of GPS at e 22 may blink every 2 sec instead of position data 4 Distress call Simple operation A distress call should be transmitted if in the opnion of the Master the ship or a person is in distress and requires imme diate assistance A distress call should include the ship s position and time They are included automatically when a GPS receiver is con nected If no GPS is connected input them if possible y NEVER USE THE DISTRESS CALL WHEN 7 YOUR SHIP IS NOT IN AN EMERGENCY DIS Y TRESS CALL CAN BE USED ONLY WHEN IM 2 MEDIATE HELP IS NEEDED
19. ed with your controller allows dashboard or overhead mounting Please read the fol lowing instructions carefully Mount the controller securely with bolts and nuts or it may come loose as a result of wave shocks or vibration Mount the controller so that the face of the controller is at 90 degrees to your line of sight when operating it CAUTION KEEP the controller at least 1 m away from your ship s mag netic navigation compass CHECK the installation angle the function display may not be easy to read at some angles OVERHEAD MOUNTING RES 902 065 DASHBOARD MOUNTING with optional MB 75 For mounting the DS 100 to a dashboard panel International channels VHF MARINE CHANNEL LIST 6 CH Frequency MHz Frequency MHz Frequency MHz Frequency MHz Frequency MHz Frequency MHz Transmit Receive CH Transmit Receive CH Transmit Receive CH Transmit Receive CH Transmit Receive CH Transmit Receive 01 156 050 160 650 11 156 550 156 550 21 157 050 161 650 62 156 125 160 725 72 156 625 156 625 84 157 225 161 825 02 156 100 160 700 12 156 600 156 600 22 157 100 161 700 63 156 175 160 775 73 156 675 156 675 85 157 275 161 875 03 156 150 160 750 13 156 650 156 650 23 157 15
20. ightness then push ENT Push A or W one or more times or numeral keys in stead to adjust the brightness Brightness level indication 1 dark to 8 bright Push ENT to determine the brightness or push CLR to exit the Set up menu SET UP 4 Contrast Adjusting the contrast D Push CALL then push V one or more times to select Set up then push ENT 2 Select Contrast then push ENT 3 Push A W one or more times or numeral keys in stead to adjust the contrast Contrast level indication 1 low to 8 high 4 Push ENT to determine the brightness or push CLR to exit the Set up menu MMSI check Your ID code can be displayed via the set up menu Check your ID Push CALL then push V one or more times to select Set up then push ENT Select MMSI check then push ENT 3 Your ID code shows on the SML chock display 267350012 4 Push CLR to exit the Set up menu lt CLRDExit gt 19 5 CONNECTION AND INSTALLATIONS Connection diagram 13 8V DC GND 1 7 NOTE Binding the GPS cable GPS connector and clone 2 receptacle with the water resistant tape increases the 2 water proofing of the controller SS 20 Rear panel description Q CONNECTION CABLE Connets to the IC M501EURO rear DSC controller recep tacle RECEIVE ANTEN
21. istress 09 21 lt CLRDExit M Message contents Distress ID 2345678 Piracy attack Distress time amp Pos Time UTC 12 34 Pos Lat 12 34 N Lon 123 45 W lt clear 13 14 WHEN RECEIVING A CALL Other messages Individual call D Push CALL then push V several times to select Re ceived calls then push ENT Select Other message then push ENT 3 Select Individual call then push ENT e Push A to scroll the message Push A a to clear the mes sage EY wn e ect a message ACK cal ndi vi dual ndi vi dual cal ships call stress stress relay istress RLY ACK istress ACK co WV O gt A e r R gt Exit ENT gt 0K gt J lt Message contents gt Routine to Indivi dua From DS 100 SN3 F3E G3E si mpl ex CH88 No information lt clear Group call D Push CALL then push V several times to select Re ceived calls then push ENT 2 Select Other message then push ENT Select Group call then push ENT Push A or W to scroll the message Push A a to clear the mes sage ect a message ACK cal ndi vi dual ndi vi dual Group cal All shi ps call Distress Distress relay
22. l repeat will be canceled and a distress acknowledgement is automati cally transmited with your own MMSI Use the CLR key only when you want to cancel repeated Z7 transmission After receiving acknowledgement call The following should be commenced with your voice trans mission after receiving a distress acknowledgement from a coast station or another ship MAY DAY e This is your ship name The 9 digit identity AND the call sign or other iden tification of the ship The ship s position if the DSC distress does not in clude it The nature of the distress and assistance required Any other information which might facilitate the res cue WHEN RECEIVING A CALL To receive a DSC call When receiving a DSC call You should act in one of the following ways depending on the received DSC format or category Wait for a voice transmission on the traffic frequency Transmit an acknowledgement with DSC or voice Transmit a distress relay call only when the ship in dis tress requires voice communications 9 Display example and operation Monitoring the traffic frequency and Monitor the communication between the calling ship and a coast station When no communication is made contact the ship using voice transmission Emergency alarm sounds for 2 min or push CLR to cancel the alarm 3 Monitoring the traffic frequency The calling statio
23. n transmits via voice on the traffic frequency Emergency alarm or con tinuous beeps depending on the category sounds until pushing CLR Transmit an acknowledgement When the following DSC is re ceived an acknowledgement must be sent back to the calling station Continuous beeps or emer gency alarm depending on the category sounds until pushing CLR 2 RCV AL ships call From ICOM DSC Category Routine lt CLREXxit When receiving an All ships calll f RCV Individual From ICOM DSC Able to comply lt CLRDExit ENTOK gt M When receiving an Individual acknowledgement 10 WHEN RECEIVING A CALL B When receive a Distress call When receiving a Distress call When receiving a distress call an alarm Pi po sounds with max AF level continuously And at the same time the trans ceiver s IC M501EURO oper ating channel changes to CH 16 automatically Push CLR to cancel the alarm RCV Distress call Distress ID 23456789 Distress time amp pos Time UTC 12 34 Pos Lat 12 34 N Lon 123 45 W When receiving an individual call When receiving an individual call an alarm Pi pi sounds Push ENT then the oper ating channel changes to designated channel e Push CLR to record the received information then the screen goes back to de fault
24. rm Pi pi sounds Push ENT then the oper ating channel changes to designated channel Push CLR to record the received information then the screen goes back to de fault RCV Group call From DS 100 SN3 Inc CLRoExi t ENT 0K gt Received message RCV MSG When receiving a DSC call the received format specifier and its contents are memorized into the received message RCV MSG memory Distress calls including other calls with dis tress category are stored separately from other calls Up to 20 distress calls can be memorized and up 20 other categories of calls can be memorized However the distress calls are saved until being erased while other calls are erased when the power is turned OFF Select a subject Entry Position Ti me Individual call Group call All ships call Received calls Distress setting WHEN RECEIVINGACALL 3 Distress message D Push CALL then push V one or more times to select Received calls then push ENT Select a Distress message then push ENT Select a desired message then push ENT Push A or W to scroll the message Push A a then push 1 to clear the message Select a message PDistress message Other message lt CLRDExit ENTOK gt lt Select message gt m1 Distress 12 21 2 Distress 11 21 3 Distress 10 21 4 D
25. splay the CE symbol on the serial number seal comply with the essential require ments of the European Radio and Telecommunication Termi nal Directive 1999 5 EC This warning symbol indicates that this equipment oper ates in non harmonised frequency bands and or may be sub ject to licensing conditions in the country of use Be sure to check that you have the correct version of this radio or the correct programming for this radio to comply with national li censing requirements TABLE OF CONTENTS FOREWORD teet det eost i IMPORTANT st en ee e eeu i EXPLICIT DEFINITIONS a i FEATURES iem Ini i WARNING CAUTIONS ii TABLE OF CONTENTS sess enne iii 1 PANEL DESCRIPTION 1 2 Bi Eront panel 1 B Function display 2 2 CALL PROCEDURE 22 2 5 3 8 Distress call Simple operation 3 Distress call Regular operation 4 Entry Position Time 5 Distress call to ship 6 Individual call 6 icta tuns 7 W ALL ships call
26. t Abandoning ship phone frequency ch 16 au Piracy attack tomatically an overboard The controller is still waiting for EPIRB emission an acknowledgment call on ch 70 When receiving the acknowl edgment reply to the con nected station via the transceiver s microphone as a icine Sh described on the page at GPS UTC 15 22 right 12 34 N 123 45 W 4 gt lt Push and hold DISTRESS for 5 sec gt NOTE nature of distress will be recorded for 10 min until a distress call transmits Distress call repeats every 3 5 4 5 min until receiving an ac knowledgement Beep Pi Pi sounds with the max volume every 1 sec Push DISTRESS button to transmit a renewed distress call Push CLR to cancel the Call repeat mode The cancel acknowledgement is automatically transmitted when the CLR key is pushed CALLPROCEDURE 2 E Entry Position Time When no GPS receiver is connected the Entry Position Time appears at the top of subject menu Push CALL then push V to select Entry Position Time 2 Push ENT then enter the latitude data with key pad 3 Push to select north latitude or S south latitude then push ENT Push 4 F to move the cur a position sor then push to correct the data Latitude Push CLR to Exit the menu mE Push A a the push ENT to E enter a Null
27. the number again 3 Enter the desired name for the ID code then push ENT Push A a several times to tog gle capital letters small letters and numerals Push the corresponding key one or more times to input the desired character Push BS to erase the character Push 4 to reverse the cursor position gt ot forward the cursor position 4 Push CLR to exit the screen Add an address ID Delete address ID Add a group ID Delete a group ID CLRoExit ENT 0K 7 Add an adress D gt a ID 9digit 15charactors CLRoExit ENT 0K 2 17 18 4 SET UP Delete address ID D Push V to select Delete address ID then push ENT Push several times to select a desired address ID that you want to delete then push ENT Address ID and name is dis played on the screen Push ENT to delete the ad Delete address D gt dress ID 05 100 SN10 Push CLR to exit the DS 100 SN2 Screen DS 100 SN3 DS 100 SN4 4 Push CLR to exit the menu CLRExi t ENT0K Delete this ID ID 9digit 2673500100 Name 15charactors DS 100 SN10 CLRoExit ENT 0K M J Add a group ID Push several timesto select Add a group ID then lt ga push ENT D 881910 2 Push numeral keys to input 0 an address ID code then Name 15charac
28. tors push ENT When a wrong number is input lt CLRExit ENT gt 0K gt push CLR then correct i J number again 3 Enter the desired name for the ID code then push ENT Push A a several times to toggle capital letters small letters and numerals Push the corresponding key one or more times to input the de sired character Push BS to erase the character Push 4 to reverse the cursor position or forward the cur Sor position 4 Push CLR to exit the screen Delete a group ID D Push V to select Delete a group ID then push ENT Push several times to select a desired address ID that you want to delete then push ENT Address ID and name is displayed on the screen 3 Push ENT to delete the address ID Push CLR to exit the screen 4 Push CLR to exit the menu Offset time Local time can be used when the GPS position data is valid and off set time is input 09 30 Offset ti m D Push CALL then push V one or more times to select Set up then push ENT CLRoExi t ENT 0K Select Offset time then 7 push ENT Push 0 or 1 space then input the time differences 4 Push ENT to determine the time or push CLR to exit the Set up menu B Brightness Adjusting the brightness D Push CALL then push V one or more times to select Set up then push ENT Select Br
29. y turn the transmitter off after 1 2 minutes etc CAUTIONS WARNING NEVER connect the controller to an AC outlet This may pose a fire hazard or result in an electric shock NWARNING NEVER transmit a distress call when your vessel does not need immediate help Distress calls can be used only in times of emergency NEVER connect the controller to a power source of more than 16 V DC Such a connection will ruin the controller NEVER place the controller where normal operation of the ship may be hindered or where it could cause bodily injury NEVER expose the controller to rain snow or any liquids AVOID using or placing the controller in direct sunlight or in areas with temperatures below 20 4 F or above 60 C 140 F KEEP the controller out of the reach of children KEEP the antenna cable and DC power cable as far away as possible from electrical pumps generators and other elec tronic instruments to prevent instrument malfunctions KEEP the controller and microphone at least 1 meter away from your vessel s magnetic navigation compass DO NOT operate the controller without running the ves sel s engine When your vessel s engine is OFF and the con troller is transmitting the vessel s battery will soon become exhausted DO NOT use chemical agents such as benzene or alcohol when cleaning as they can damage the terminal unit sur faces CEO CE Versions of the DS 100 which di
Download Pdf Manuals
Related Search