IBM 600X (MT 2646) Laptop User Manual
Contents
1. Switch The maximum current requirements are 10 amps at 100 VAC or 4 2 amps at 240 VAC a Attach the AC power cords to the Power Supply blades and wall outlets or power strips Secure the strain CHASSIS CHASSIS relief bales to the plugs Place the On Off switches in GOOD LED NS P FAULT LED F F L F k the On position The switch runs its self tests and begins normal g operation this may take a few minutes Observe the i 1 i Maintenance Panel and verify that the CPUO blade r r i Heartbeat LED is blinking about once per second and the Chassis Fault LED is NOT illuminated z z F ESI cPUO HEARTBEAT LED Step 5 Verify Workstation Requirements L1 Verify that your workstation can support the Enterprise Fabric Suite 2007 application with the following minimum requirements Q a Ooooooo Windows 2003 SP1 SP2 R2 and XP 256 MB memory minimum 512 MB recommended 150 MB disk space 1 GHz processor Video card with 256 colors CD ROM drive RJ 45 Ethernet port Internet Browser Microsoft Internet Explorer 5 0 Netscape Navigator 6 0 Firefox 1 0 or Mozilla 1 5 Java 2 Standard Edition Runtime Environment 1 4 2 The default IP address of a new switch is 10 0 0 1 Ensure that your workstation is configured to communicate with the 10 0 0 subnet Step 6 Connect the Workstation to the Switch L1 Connect the CPUO blade Ethernet port directly to the workstation using an Ethernet cable or2. refer to the SANbox 9000 Series Stackable Chassis Switch Installation Guide on the product CD NOTE Do not apply power to the switch until instructed in Step 4 Step 1 Verify the Package Contents The SANbox 9000 Series Fibre Channel Switch is shipped with the following items SANbox 9000 Series Fibre Channel Switch AC Power cords Rail kit RJ 45 RS 232 console adapter Enterprise Fabric Suite 2007 CD k C ek ND imde NOTE Transceivers and stacking cables if you ordered them are packaged separately Step 2 Mount the Switch WARNING Two people are required to safely lift and install the switch into a rack To avoid personal injury or damage to the switch arrange for assistance You can mount the SANbox 9000 Series switch on a flat surface or in a rack Allow minimum clearances of 2 inches in front and 8 inches in the rear for cabling Q Fora rack mount install the SANbox 9000 Series rail kit in a standard 19 rack as described in the SANbox 9000 Series Stackable Chassis Switch Rack Mounting Guide that is packaged with the switch Step 3 Install Transceivers An SFP transceiver is required for each switch port that will be connected to a device U To install an SFP transceiver insert the transceiver into the switch port and gently press until it snaps in place The transceiver will fit only one way If the transceiver does not install under gentle pressure flip it over and try again Step 4 Apply Power to the
3. FIBRE CHANNEL SWITCH INSTALLATION XX oLocic Purchasers of OEM products should consult with the OEM for support Support Headquarters QLogic Web Site Technical Support Web Site Technical Support Email Technical Training Email North American Region Email Phone Fax Europe Middle East and Africa Region Email Phone Numbers by Language Asia Pacific Region Email Phone Numbers by Language Latin and South America Region Email Phone Numbers by Language QLogic Corporation 12984 Valley View Road Tee Prairie Minnesota 55344 3657 www qlogic com support glogic com support qlogic com tech training qlogic com support qlogic com 1 952 932 4040 1 952 974 4910 emeasupport qlogic com 353 1 6924960 English 353 1 6924961 Francais 353 1 6924962 Deutsch 353 1 6924963 Espa ol 353 1 6924964 Portugu s 353 1 6924965 Italiano apacsupportQglogic com 63 2 885 6712 English 63 2 885 6713 Mandarin 63 2 885 6714 Japanese 63 2 885 6715 Korean calasupport qlogic com 52 55 5278 7016 English 52 55 5278 7017 Espa ol 52 55 5278 7015 Portugu s Quick Start Guide Installation Instructions Congratulations on your purchase of the SANbox 9000 Series Fibre Channel Switch This guide describes the steps to install and activate your new switch using a Windows workstation For advanced options and instructions including Solaris Linux and Mac 0S X installations
4. ask from your network administrator Be sure that your workstation is configured for the same subnet Step 9 Run the Configuration Wizard Q Double click the Enterprise Fabric Suite 2007 shortcut or select Enterprise Fabric Suite 2007 from Start menu depending on how you installed it Q The Configuration Wizard tool auto detects and configures the switch based on selected options and recommended settings Follow the instructions to set network parameters and the password The default user name is admin the default password is password NOTE Ifyouare using an Ethernet switch and the auto connect process fails due to a time out try a direct connection from your workstation to the switch using an Ethernet cross over cable Step 10 Connect Devices and Switches L1 Connect fiber optic cables between the installed transceivers and their corresponding devices Each port auto negotiates the proper port type with the connected device or switch Congratulations You have successfully installed your QLogic SANbox 9000 Series Switch 2007 QLogic Corporation QLogic the QLogic logo SANbox and Enterprise Fabric Suite 2007 are trademarks or registered trademarks of QLogic Corporation Microsoft Windows and Internet Explorer are registered trademarks of the Microsoft Corporation MacOS X is a registered trademark of Apple Computer Inc Linux is a registered trademark of Linus Torvalds Mozilla and Firefox are trademarks or registered
5. indirectly through a Switch or hub The Ethernet port automatically discovers straight and cross over cables You must have a live Ethernet connection when the workstation powers up NOTE The Maintenance Panel Ethernet ports on the front of the switch are disabled and should not be used for the initial installation You can enable the Maintenance Panel Ethernet ports after the switch is operational CPU0 BLADE Wi ETHERNET PORT Step 7 Install Enterprise Fabric Suite 2007 The Enterprise Fabric Suite 2007 application includes the Configuration Wizard This wizard auto detects and configures the switch based on selected options and recommended settings To install the Enterprise Fabric Suite 2007 application on a Windows workstation server perform the following steps t Insert the Enterprise Fabric Suite 2007 disk into the CDROM drive Select the Enterprise Fabric Suite 2007 tab at the top of the screen Click Agree in response to the End User License Agreement Select Install for Windows 2003 XP Double click the Windows_6 08 xx exe file to begin installation Enter the serial number and license key provided to activate the Enterprise Fabric Suite 2007 application BS V I c If the product introduction screen does not open open the CD with Windows Explorer and run the installation program with the following path Switch ManagenWindows 6 08 xx exe Step 8 Obtain Network Configuration L1 Obtain the IP address and subnet m
6. trademarks of the Mozilla Foundation Netscape Navigator is a registered trademarks of Netscape Communications Corporation Java and Solaris are registered trademarks of Sun Microsystems Inc All other brands and product names are trademarks or registered trademarks of their respective owners Information supplied by QLogic is believed to be accurate and reliable QLogic Corporation assumes no responsibility for any errors in this brochure QLogic Corporation reserves the right without notice to makes changes in product design or specifications QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo CA 92656 949 389 6000 www qlogic com QLOGIC 50688 03 A
Download Pdf Manuals
Related Search