Husqvarna 535RX Brush Cutter User Manual
Contents
1. Do not wear jewellery shorts sandals or go barefoot Secure hair so it is above shoulder level FIRST AID KIT Always have a first aid kit nearby It Machine s safety equipment This section describes the machine s safety equipment its purpose and how checks and maintenance should be carried out to ensure that it operates correctly See the What is what section to locate where this equipment is positioned on your machine IMPORTANT All servicing and repair work on the machine requires special training This is especially true of the machine s safety equipment If your machine fails any of the checks described below you must contact your service agent When you buy any of our products we guarantee the availability of professional repairs and service If the retailer who sells your machine is not a servicing dealer ask him for the address of your nearest service agent WARNING Never use a machine with faulty safety equipment The machine s safety equipment must be checked and maintained as described in this section If your machine fails any of these checks contact your service agent to get it repaired Throttle lockout The throttle lockout is designed to prevent accidental operation of the throttle control When you press the lock A i e when you grasp the handle it releases the throttle control B When you release the handle the throttle control and the throttle lockout both move back to their2. before taking any further action If the spark plug is dirty clean it and check that the electrode gap is 0 020 inch 0 5 mm The spark plug should be replaced after about a month in operation or earlier if necessary CAUTION Always use the recommended spark plug type Use of the wrong spark plug can damage the piston cylinder Note Use only HUSQVARNA replacement parts Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others Your warranty does not cover damage or liability caused by the use of accessories and or attachments not specifically recommended by HUSQVARNA English 29 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine Most of the items are described in the Maintenance section The user must only carry out the maintenance and service work described in this manual More extensive work must be carried out by an authorized service workshop CET I X Check mare namess e idmagi TXT Check hatte suspension ingente X Make sure the throttle trigger lock and the throttle function correctly from a safety point of view Check that the Check that the stop switch works correctly switch works Check that the stop switch works correctly Check that the handle and handlebar are undamaged and secured correctly Check that the cutting attachment does not rotate atide that
3. Personal protective equipment IMPORTANT A clearing saw brushcutter or trimmer can be dangerous if used incorrectly or carelessly and can cause serious or fatal injury to the operator or others It is extremely important that you read and understand the contents of this operator s manual You must use approved personal protective equipment whenever you use the machine Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen Ask your dealer for help in choosing the right equipment WARNING Listen out for warning signals or shouts when you are wearing hearing protection Always remove your hearing protection as soon as the engine stops HELMET A helmet should be worn if the trees being cleared are taller than 2 m Wear hearing protection that provides adequate noise reduction EYE PROTECTION Always wear approved eye protection If you use a visor then you must also wear approved protective goggles Approved protective goggles must comply with standard ANSI Z87 1 in the USA or EN 166 in EU countries GENERAL SAFETY PRECAUTIONS GLOVES Gloves should be worn when necessary e g when fitting cutting attachments CS BOOTS Wear boots with steel toe caps and non slip sole E CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches Always wear heavy long pants
4. Support flange 3 Bevel gear 20 Support cup 4 Cutting attachment guard 21 Drive disc 5 Shaft 22 Blade 6 Handlebar 23 Socket spanner 7 Throttle control 24 Operators manual 8 Stop switch 25 Transport guard 9 Throttle lockout 26 Allen key 10 Suspension 27 Locking pin 11 Cylinder cover 28 Harness 12 Starter handle 29 Spark plug cap and spark plug 13 Fuel tank 30 Start throttle button 14 Choke control 31 Adjusting screw for throttle cable 15 Air purge 32 Spark plug spanner 16 Air filter cover 33 Guard extension 17 Handle adjustment English 5 GENERAL SAFETY PRECAUTIONS Important IMPORTANT The machine is only designed for trimming grass grass clearing and or forestry clearing The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data Never use the machine if you are tired if you have drunk alcohol or if you are taking medication that could affect your vision your judgement or your co ordination Wear personal protective equipment See instructions under the heading Personal protective equipment Never use a machine that has been modified in any way from its original specification Never use a machine that is faulty Carry out the checks maintenance and service instructions described in this manual Some maintenance and service measures must be carried out by trained and qualified specialists See instructions under the headin
5. T should be turned anti clockwise until the cutting attachment stops Adjustment of the idle speed Adjust the idle speed using the idle adjustment screw T if it is necessary to readjust First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate Then turn the screw anticlockwise until the cutting attachment stops The idle speed is correctly adjusted when the engine will run smoothly in every position The idle speed should also be well below the speed at which the cutting attachment starts to rotate WARNING If the idle speed cannot be adjusted so that the cutting attachment stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired Adjusting the start throttle speed The correct start throttle speed is set by means of an adjuster on the rear of the handle next to the cable Use this screw 4 mm Allen screw to increase or decrease the start throttle speed Proceed as follows 1 Run the machine at idle 2 Press the start throttle lock as described under the heading Starting and stopping 3 Ifthe start throttle speed is too low below 4000 rpm turn the adjuster screw A clockwise until the cutting attachment starts to rotate Then turn A clockwise a further 1 2 turn English 27 MAINTENANCE 4 Ifthe start throttle speed is too high turn the adjuster CAUTION Never use a machine with a defective muffler screw A a
6. extension into position on the guard with the four quick fasteners English 13 ASSEMBLY The guard extension is removed easily using the spark plug spanner see illustration mn m Fitting a blade guard grass blade and grass cutter al 6 e Hook the blade guard combination guard A onto the fitting on the shaft and secure with the bolt CAUTION Ensure that the guard extension is removed Use the recommended blade guard See the Technical data section e Fit the drive disc B on the output shaft e Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing Insert the locking pin C in the hole to lock the shaft e Place the blade D support cup E and support flange F on the output shaft Fit the nut G The nut must be tightened to a torque of 35 50 Nm 3 5 5 kpm Use the socket spanner in the tool kit Hold the shaft of the spanner as close to the blade guard as possible To tighten the nut turn 14 English the spanner in the opposite direction to the direction of rotation Caution left hand thread mm Fitting the blade guard and saw blade als 916 e Remove the mounting plate H Fit the adapter I and bracket J with the two screws K as shown Fit the blade guard A to the adapter using the 4 screws L as shown CAUTION Use the recommended blade guard See the Technical
7. firmly with your feet apart Move forward after the return stroke and stand firmly again Let the support cup rest lightly against the ground It is used to protect the blade from hitting the ground Reduce the risk of material wrapping around the blade by following these instructions 1Always work at full throttle 2Avoid the previously cut material during the return stroke Stop the engine unclip the harness and place the machine on the ground before you start to collect the cut material Grass trimming with a trimmer head Trimming Hold the trimmer head just above the ground at an angle It is the end of the cord that does the work Let the cord work at its own pace Never press the cord into the area to be cut V RUNAWAY s The cord can easily remove grass and weeds up against walls fences trees and borders however it can also damage sensitive bark on trees and bushes and damage fence posts Reduce the risk of damaging plants by shortening the cord to 10 12 cm and reducing the engine speed Clearing The clearing technique removes all unwanted vegetation Keep the trimmer head just above the ground and tilt it Let the end of the cord strike the ground around trees posts statues and the like CAUTION This technique increases the wear on the cord Rave MI AAW The cord wears quicker and must be fed forward more often when working against stones brick concrete metal fences etc than
8. get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in burns to the skin Remember the risk of fire WARNING The inside of the muffler contain chemicals that may be carcinogenic Avoid contact with these elements in the event of a damaged muffler WARNING Bear in mind that The exhaust fumes from the engine are hot and may contain sparks which can start a fire Never start the machine indoors or near combustible material A locking nut is used to secure some types of cutting attachment When fitting tighten the nut in the opposite direction to the direction of rotation of the cutting attachment To remove it undo the nut in the same direction as the cutting attachment rotates CAUTION The nut has a left hand thread Tighten the nut using the socket spanner The nylon lining inside the locking nut must not be so worn that you can turn it by hand The lining should offer a resistance of at least 1 5 Nm The nut should be replaced after it has been put on approx 10 times 10 English Cutting equipment This section describes how to choose and maintain your cutting equipment in order to e Reduce the risk of blade thrust e Obtain maximum cutting performance e Extend the life of cutting equipment IMPORTANT Only use cutting attachments with the guards we recommend See the chapter on Technical data Refer to the inst
9. quarters full with lubricant Fill 4 necessary using special grease Check that the Check that the safety release on the harness is not damaged and works release on the harness is not damaged and works A Check the fuel filter from contamination and the fuel hose from cracks or other defects Replace if necessary Check all cables and connections I Kr Ei Check the clutch clutch springs and the clutch drum for wear Replace X if necessary by an autorized service workshop Replace the spark plug Check that the spark plug is fitted with a X suppressor Check and clean the spark arrestor screen on the muffler only applies to mufflers fitted with a catalytic converter 30 English TECHNICAL DATA Technical data Technical data Motor Cylinder displacement cu in cm Cylinder bore inch mm Stroke inch mm Idle speed rpm Recommended max speed rpm Speed of output shaft rpm Max engine output acc to ISO 8893 kW rpm Catalytic converter muffler Speed regulated ignition system Ignition system Spark plug Electrode gap inch mm Fuel and lubrication system Fuel tank capacity US pint litre Weight Weight without fuel cutting attachment and guard Lbs kg Sound levels see note 1 Equivalent sound pressure level at the user s ear measured according to ANSI B175 3 1997 dB A min max Equipped with trimmer head original Equipped with grass blade original Vibration levels se
10. 18 gu m ee 18 EI 19 STARTING AND STOPPING Check before starting ciali 20 Starting and stopping rin 20 WORKING TECHNIQUES General working instructions 22 MAINTENANCE i m 27 nj c 28 Cooling system lane 28 Bevel geal cc 28 AIr TIET credi 29 Spark BUS rl 29 Maintenance schedule 30 TECHNICAL DATA Technical data caga 31 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS 33 Note the following before starting Please read the operators manual carefully Maintenance replacement or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual WARNING Long term exposure to noise can result in permanent hearing impairment So always use approved hearing protection WARNING Under no circumstances may the design of the machine be modified without the permission of the manufacturer Always use genuine accessories Non authorized modifications and or accessories can result in serious personal injury or the death of the operator or others Your warranty may not cover damage or liability caused by the use of non authorized accessories or replacement parts WARNING A clearing saw brushcutter or trimmer can be dangerous if used incorrectly or carelessly and can cause serious or fatal injury to t
11. OBLIGATIONS The EPA U S Environmental Protection Agency CARB California Air Resources Board Environment Canada and Husqvarna Forest amp Garden are pleased to explain the emissions control system s warranty on your 2009 and later small off road engine In U S and Canada new equipment that use small off road engines must be designed built and equipped to meet the applicable Federal or Californian stringent anti smog standards Husqvarna Forest amp Garden must warrant the emissions control system on your small off road engine for the period listed below provided there has been no abuse neglect or improper maintenance of your equipment Your emissions control system may include parts such as the carburetor ignition system catalytic converter fuel tank filters and other associated components Also included may be hoses belts connectors sensors and other emission related assemblies Where a warrantable condition exists Husqvarna Forest amp Garden will repair your small off road engine at no cost to you including diagnosis parts and labor MANUFACTURER S WARRANTY COVERAGE The emissions control system is warranted for two years If any emissions related part on your equipment is defective the part will be repaired or replaced by Husqvarna Forest amp Garden OWNER S WARRANTY RESPONSIBILITIES e As the small off road engine owner you are responsible for performance of the required maintenance listed in your
12. Operator s manual 535RX 535RXT Please read the operator s manual carefully and make sure you understand the instructions before using the machine e _ __ _ t4n Symbols WARNING Clearing saws brushcutters and trimmers can be dangerous Careless or incorrect use can result in serious or fatal injury to the operator or others Please read the operator s manual carefully and make sure you understand the instructions before using the machine Always wear e Aprotective helmet where there is a risk of falling objects e Approved hearing protection e Approved eye protection Max speed of output shaft rpm x Watch out for thrown objects and ricochets The operator of the machine must ensure while working that no persons or animals come closer than 15 metres KEY TO SYMBOLS Only use non metallic flexible cutting attachments i e trimmer heads with trimmer cord Starting instructions Other symbols decals on the machine refer to special certification requirements for certain markets The engine is switched off by moving the stop switch to the stop position CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance Machines fitted with saw blades or grass blades can be thrown violently to the side whe
13. ase fitted at the front as a safety precaution in case the engine catches fire or in any other situation that requires you to free yourself from the machine and harness See instructions under the heading Adjusting the harness and brush cutter Certain harnesses also have a quick release fitted to the support hook Check that the harness straps are correctly positioned Once the harness and machine have been adjusted check that the harness quick release works correctly Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases In countries that have a warm and dry climate there is a significant risk of fire We therefore fit certain mufflers with a spark arrestor screen Check whether the muffler on your machine is fitted with this kind of screen For mufflers it is very important that you follow the instructions on checking maintaining and servicing your machine Never use a machine that has a faulty muffler Regularly check that the muffler is securely attached to the machine If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly A blocked screen will cause the engine to overheat and may lead to serious damage English 9 GENERAL SAFETY PRECAUTIONS WARNING Mufflers fitted with catalytic converters
14. d due to fatigue or due to being tightened too much Discard the support flange if it is cracked WARNING The complete clutch cover and shaft must be fitted before the machine is started otherwise the clutch gt can come loose and cause personal KZ injury Ensure the locking nut has not lost its captive force Always move the machine away from the The nut lock should have a locking force of at least 1 5 refuelling area and source before Nm The tightening torque of the locking nut should be starting Place the machine on a flat 35 50 Nm surface Ensure the cutting attachment cannot come into contact with any object Make sure no unauthorised persons are l in the working area otherwise there is a Check that the blade guard is not damaged or risk of serious personal injury The safety cracked Replace the blade guard if it is exposed to distance is 15 metres impact or is cracked Starting gt Choke Set the choke control in the choke position e Check that the trimmer head and trimmer guard are not damaged or cracked Replace the trimmer head or 20 English STARTING AND STOPPING Primer bulb Press the air purge repeatedly until fuel For throttle handles with a start throttle begins to fill the bulb The bulb need not be completely lock filled Set the throttle to the start position by first pressing the throttle lockout and the throttle trigger then pressing the start throttle button A The
15. d take out the filter Wash it clean in warm soapy water Ensure that the filter is dry before refitting it An air filter that has been in use for a long time cannot be cleaned completely The filter must therefore be replaced with a new one at regular intervals A damaged air filter must always be replaced If the machine is used in dusty conditions the air filter should be soaked in oil See instructions under the heading Oiling the air filter Oiling the air filter Always use HUSQVARNA filter oil art no 531 00 92 48 The filter oil contains a solvent to make it spread evenly through the filter You should therefore avoid skin contact Put the filter in a plastic bag and pour the filter oil over it Knead the plastic bag to distribute the oil Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine Never use common engine oil This would drain through the filter quite quickly and collect in the bottom Spark plug e The spark plug condition is influenced by Incorrect carburetor adjustment e An incorrect fuel mixture too much or incorrect type of oil e A dirty air filter These factors cause deposits on the spark plug electrodes which may result in operating problems and starting difficulties If the machine is low on power difficult to start or runs poorly at idle speed always check the spark plug first
16. data section e Fit the drive disc B on the output shaft Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing ASSEMBLY Insert the locking pin C in the hole to lock the shaft Place the blade D and support flange F on the output shaft Fit the nut G The nut must be tightened to a torque of 35 50 Nm 3 5 5 kom Use the socket spanner in the tool kit Hold the shaft of the spanner as close to the blade guard as possible To tighten the nut turn the spanner in the opposite direction to the direction of rotation Caution left hand thread When loosening and tightening the saw blade nut there is a risk of injury from the teeth of the saw blade You should therefore always ensure that your hand is shielded by the blade guard when doing this Always use a socket spanner with a shaft that is long enough to allow this The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut Fitting other guards and cutting attachments Se Fit the trimmer guard combination guard A intended for use with the trimmer head plastic blades CAUTION Ensure that the guard extension is fitted Hang the trimmer guard combination guard A on the two hooks on the plate holder M Bend the guard around the shaft and tighten it with the bolt L on the opposite side of the shaft Use the lock
17. e around without first checking e You should plan the strip so that you avoid going over behind you to make sure no one is within ditches or other obstacles on the ground You should the safety zone also orient the strip to take advantage of wind conditions so that cleared stems fall in the cleared area of the stand e Onsloping ground you should work along the slope It is much easier to work along a slope than it is to work up and down it WARNING Sometimes branches or grass get caught between the guard and cutting attachment Always stop the engine before cleaning S Working methods TA WARNING Machines fitted with saw E blades or grass blades can be thrown violently to the side when the blade comes gt lt TATA into contact with a fixed object This is Kas NT called blade thrust A blade thrust can be Pis violent enough to cause the machine and or operator to be propelled in any direction and possibly lose control of the machine Blade thrust can occur without warning if the machine snags stalls or binds Blade thrust is more likely to occur in areas where it is difficult to see the material being cut Avoid cutting with the area of the blade between the 12 o clock and 3 o clock positions Because of the speed of rotation of the blade blade thrust can occur if you attempt to cut thick stems with this area of the blade Before you start clearing check the clearing area the type of terrain the
18. e note 2 Vibration levels at handles measured according to ANSI B175 3 1997 m s Equipped with trimmer head original left right Equipped with grass blade original left right NOTE This spark ignition system complies with the Canadian standard ICES 002 535RX 2 11 34 6 1 50 38 0 1 20 80 5 2900 11500 8220 1 6 8400 Ves Ves Champion RCJ 6Y 0 02 0 5 1 27 0 6 13 4 6 1 95 95 3 0 3 4 3 4 4 1 535RXT 2 11 34 6 1 50 38 0 1 20 30 5 2900 11500 8220 1 6 8400 Yes Yes Champion RCJ 6Y 0 02 0 5 1 27 0 6 6 2 95 96 2 4 3 1 2 5 2 7 Note 1 Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion standard deviation of 1 dB A Note 2 Reported data for equivalent vibration level has a typical statistical dispersion standard deviation of 1 m s English 31 TECHNICAL DATA mm Output shaft thread M12 Multi 255 3 Y 255 3 teeth 537 33 16 01 Grass 255 4 255 4 teeth 537 33 16 01 Grass blade grass cutter Multi 275 4 Y 275 4 teeth 537 33 16 01 537 33 16 01 Multi 300 3 300 3 teeth Saw blade Scarlet 200 22 O 200 22 teeth 537 38 77 01 Tricut Y 300 mm Separate blades Plastic blades have part number 531 01 77 15 537 33 16 01 537 34 94 01 T35 T35x 2 4 3 0 mm cord 537 33 16 01 537 34 94 01 32 English FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND
19. e or after being cut If you 22 English WORKING TECHNIQUES e Start at whichever end of the area is easiest and clear WARNING Neither the operator of the an open space from which to work machine nor anyone else may attempt to remove the cut material while the engine Work systematically to and fro across the area is running or the cutting equipment is clearing a width of around 4 5 m on each pass This rotating as this can result in serious exploits the full reach of the machine in both directions injury and gives the operator a convenient and varied working area to work in Stop the engine and cutting equipment du before vou remove material that has NL ye wound around the blade shaft as Wy al otherwise there is a risk of injury The Ma jd d TS bevel gear can get hot during use and b B may remain so for a while afterwards You VIS DIN 3 u could get burnt if you touch it Y y Z LN a Sa xU amp e WARNINGI Watch out for thrown objects Ne JE es N Always wear approved eye protection an e Never lean over the cutting attachment age SY guard Stones rubbish etc can be thrown e AVR up into the eyes causing blindness or AAA ENS EN SEJOLS Misty Clear a strip around 75 m long Move your fuel can as Keep unauthorised persons at a distance work progresses Children animals onlookers and helpers should be kept outside the safety zone of 15 m Stop the machine immediately if anyone approaches Never swing the machin
20. en performing all service measures WARNING Take care when handling fuel Bear in mind the risk of fire explosion and inhaling fumes A Fuel CAUTION The machine is equipped with a two stroke engine and must always been run using a mixture of gasoline and two stroke engine oil It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained When mixing small amounts of fuel even small inaccuracies can drastically affect the ratio of the mixture WARNING Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin For this reason observe caution when handling fuel and make sure there is adequate ventilation 18 English Gasoline pla CAUTION Always use a quality gasoline oil mixture with an octane rating of at least 87 octane RON MON 2 If your machine is equipped with a catalytic converter see chapter on Technical data always use a good quality unleaded gasoline oil mixture Leaded gasoline will destroy the catalytic converter Use low emission gasoline also known as alkylate gasoline if it is available This engine is certified to operate on unleaded gasoline The lowest recommended octane grade is 87 RON MON 2 If you run the engine on a lower octane grade than 87 so called knocking can occur This gives rise to a high engine temperature and increased bearing l
21. ended setting tool An incorrectly set saw blade increases the risk of jamming and blade thrust and damage to the saw blade Check the cutting attachment for damage or cracks A damaged cutting attachment should always be replaced SaS y D Sharpening grass cutters and grass blades ERA 91 e See the cutting attachment packaging for correct sharpening instructions Sharpen blades and cutters using a single cut flat file WARNING Always discard a blade that is bent twisted cracked broken or damaged in any other way Never attempt to straighten a twisted blade so that it can be reused Only use original blades of the specified type Sharpening the saw blade Als e See the cutting attachment packaging for correct sharpening instructions A correctly sharpened blade is essential for working efficiently and to avoid unnecessary wear to the blade and brush cutter e Make sure that the blade is well supported when you file it Use a 5 5 mm round file with a file holder e The filing angle is 15 File alternate teeth to the right and those in between to the left If the blade has been heavily pitted by stones it may be necessary to dress the top edges of the teeth with a flat file in exceptional cases If so this should be done before filing with a English 11 GENERAL SAFETY PRECAUTIONS round file The top edges must be filed down by the same amount for all the tee
22. ened to transfer more load from the shoulder straps to the hip strap English 17 FUEL HANDLING Fuel safety Never start the machine 1 If you have spilled fuel on it Wipe off the spillage and allow remaining fuel to evaporate 2 If you have spilled fuel on yourself or your clothes change your clothes Wash any part of your body that has come in contact with fuel Use soap and water 3 If the machine is leaking fuel Check regularly for leaks from the fuel cap and fuel lines Transport and storage e Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames for example from electrical machinery electric motors electrical relays switches or boilers e When storing and transporting fuel always use approved containers intended for this purpose When storing the machine for long periods the fuel tank must be emptied Contact your local gas station to find out where to dispose of excess fuel Ensure the machine is cleaned and that a complete service is carried out before long term storage The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage e Secure the machine during transport e In order to prevent unintentional starting of the engine the spark plug cap must always be removed during long term storage if the machine is not under close supervision and wh
23. for a period of two years WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty must be performed at no charge to the owner at a warranty station Warranty services or repairs will be provided at all Husqvarna Forest amp Garden distribution centers that are franchised to service the subject engines Throughout the emissions warranty period of two years Husqvarna Forest amp Garden must maintain a supply of warranted parts sufficient to meet the expected demand for such parts WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance schedule is warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part will be repaired or replaced by Husqvarna Forest amp Garden at no cost Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part Any warranted part that is not scheduled for replacement as required in the maintenance schedule is warranted for two years If any such part fails during the period of warranty coverage it will be repaired and replaced by Husqvarna Forest amp Garden at no cost Any such part repaired or replaced under the warranty is warranted for the remaining warranty period Any warranted part that is scheduled only for re
24. g Maintenance All covers guards and handles must be fitted before starting Ensure that the spark plug cap and ignition lead are undamaged to avoid the risk of electric shock The machine operator must ensure that no people or animals come closer than 15 metres while working When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres Do an overall inspection of the machine before use see maintenance schedule WARNING This machine produces an electromagnetic field during operation This field may under some circumstances interfere with active or passive medical implants To reduce the risk of serious or fatal injury we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine WARNING Running an engine ina confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning 6 English WARNING Never allow children to use or be in the vicinity of the machine As the machine is equipped with a spring loaded stop switch and can be started by low speed and force on the starter handle even small children under some circumstances can produce the force necessary to start the machine This can mean a risk of serious personal injury Therefore remove the spark plug cap when the machine is not under close supervision
25. gular inspection in the maintenance schedule will be warranted for a period of two years A statement in such written instructions to the effect of repair or replace as necessary will not reduce the period of warranty coverage Any such part repaired or replaced under warranty will be warranted for the remaining warranty period DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station CONSEQUENTIAL DAMAGES Husqvarna Forest amp Garden is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part English 33 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe airfilter holder and carburetor bolts 3 Airfilter and fuelfilter covered up to maintenance schedule Spark Plug covered up to maintenance schedule Ignition Module Muffler with catalytic converter NO o A Fuel tank WHAT IS NOT COVERED All failures caused by abuse neglect or improper maintenance are not covered ADD ON OR MODIFIED PARTS Add on or modified parts that are not exempted by CARB or EPA may not be used The use of any non exempted add on or modified parts will be grounds for disallowing a warranty claim Husqvarna Forest amp Garden will not be liable to
26. he harness for the support hook 2 Grass clearing The machine should be supported in a harness when grass clearing so that the cutting equipment is parallel to the ground Quick release Push down the red release lever to release the machine from the harness WA Adjusting the harness 1 Tighten the hip strap so that it sits securely ASSEMBLY 2 Tighten the chest strap under your left arm so that it Correct balance fits closely around your body 1 Forestry clearing The machine is balanced by moving the suspension ring on the machine forwards or backwards On some models the suspension ring is fixed however this will then have a number of holes for the support hook The machine is correctly balanced when it freely hangs horizontally from the support hook In this way the risk of hitting stones is reduced if you need to release the handlebar 3 Adjust the shoulder strap to distribute the load evenly across your shoulders Press downwards on the suspension hook to load the harness Husqvarna 2 Grass clearing Let the blade balance at a comfortable cutting height i e close to the ground 4 Adjustthe height of the suspension hook as described in the instructions for the standard harness Forestry clearing 5 Ifyou need to lower the suspension hook for trimming for example move the suspension strap A to the lower mounting point on the backplate 6 The elastic strap B can be tight
27. he operator or others It is extremely important that you read and understand the contents of this operator s manual a EMISSION CONTROL INFORMATION E J jHusqvarna EEE ue HUSQVARNA AB HUSKVARNA SWEDEN Eu THIS ENGINE MEETS US EPA AND CALIFORNIA EXH EVP REGS FOR EX SORE REFER TO OPERATOR S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS EMISSONS COMPLIANCE PERIOD III The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal and Californian emissions requirements The engine exhaust from this product contains chemical known to the State of California to cause cancer birth defects or other reproductive harm English 3 INTRODUCTION Dear customer Congratulations on your choice to buy a Husqvarna product Husqvarna is based on a tradition that dates back to 1689 when the Swedish King Karl Xl ordered the construction of a factory on the banks of the Huskvarna River for production of muskets The location was logical since water power was harnessed from the Huskvarna River to create the water powered plant During over 300 years of continuous operation the Husqvarna factory has produced a lot of different products from wood stoves to modern kitchen appliances sewing machines bicycles motorcycles etc In 1956 the first motor driven lawn mowers appeared followed by chain saws i
28. hock if the spark plug cap has been damaged Always use gloves Do not use a machine with damaged spark plug cap English 21 WORKING TECHNIQUES General working instructions position yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control Both situations can cause IMPORTANT serious personal injury This section describes the basic safety precautions for working with brush cutters and trimmers If you encounter a situation where you are uncertain how to proceed you should ask an expert Contact your dealer or your service workshop Avoid all usage which you consider to be beyond your capability You must understand the difference between forestry clearing grass clearing and grass trimming before use 6 Keep a good balance and a firm foothold Do not overreach Keep proper footing and balance at all times Basic safety rules 7 Always hold the machine with both hands Hold the machine on the right side of your body Keep all parts N O of your body away from the hot surfaces Keep all parts of your body away from the rotating cutting 1 Look around you attachment e To ensure that people animals or other things cannot affect your control of the machine e To ensure that people animals etc do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment e CAUTION Do not use the machi
29. in demanding conditions A dirty or blocked cooling done with a wire brush On mufflers without a catalytic system results in the machine overheating which causes converter the screen should be cleaned weekly or damage to the piston and cylinder replaced if necessary On mufflers fitted with a catalytic converter the screen should be checked and if necessary Bevel gear cleaned monthly If the screen is damaged it should be replaced If the screen is frequently blocked this canbe The bevel gear is filled with the right quantity of grease at a sign that the performance of the catalytic converter is the factory However before using the machine you impaired Contact your dealer to inspect the muffler A should check that the bevel gear is filled three quarters blocked screen will cause the machine to overheat and full with grease Use HUSQVARNA special grease result in damage to the cylinder and piston The grease in the bevel gear does not normally need to be changed except if repairs are carried out 28 English MAINTENANCE Air filter x The air filter must be regularly cleaned to remove dust and dirt in order to avoid e Carburettor malfunctions Starting problems e Loss of engine power e Unnecessary wear to engine parts Excessive fuel consumption Clean the filter every 25 hours or more regularly if conditions are exceptionally dusty Cleaning the air filter Remove the air filter cover an
30. ing pin C Place the locking pin in the groove on the screw head and tighten See diagram Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing Insert the locking pin C in the hole to lock the shaft Screw on the trimmer head plastic blades H in the opposite direction to the direction of rotation order English 15 ASSEMBLY Adjusting the harness and brush cutter WARNING When using a brush cutter it must always be hooked securely to the harness Otherwise you will be unable to control the brush cutter safely and this can result in injury to yourself or others Never use a harness with a defective quick release Standard harness ma Quick release At the front is an easily accessible quick release Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness Spreading the load on your shoulders A well adjusted harness and machine makes work much easier Adjust the harness for the best working position Tension the side straps so that the weight is evenly distributed across both shoulders Correct height 1 Forestry clearing The machine should be supported in a harness when forestry clearing so that the cutting equipment is angled slightly forwards in relation to the ground Adjust the 16 English height using the strap on t
31. n 1959 and it is within this area Husqvarna is working today Today Husqvarna is one of the leading manufacturers in the world of forest and garden products with quality as our highest priority We develop manufacture and market high quality motor driven products for forestry and gardening as well as for building and construction industry Your purchase gives you access to professional help with repairs and service whenever this may be necessary If the retailer who sells your machine is not one of our authorized dealers ask for the address of your nearest servicing dealer It is our wish that you will be satisfied with your product and that it will be your companion for a long time Think of this operator s manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you ever lend or sell this machine make sure that the borrower or buyer gets the operator s manual so they will also know how to properly maintain and use it Thank you for using a Husqvarna product Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice For customer assistance contact us at our website www usa husqvarna com 4 English WHAT IS WHAT What is what on the brush cutter 1 Trimmer head 18 Locking nut 2 Grease filler cap bevel gear 19
32. n release the throttle lockout and the throttle trigger followed by the start throttle button The throttle function is now activated To return the engine to idle press the throttle lockout and throttle trigger again WARNING When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately Hold the body of the machine on the ground using your left hand CAUTION Not with your foot Grip the starter Stopping handle slowly pull out the cord with your right hand until you feel some resistance the starter pawls grip now quickly and powerfully pull the cord Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts When the Stop the engine by switching off the ignition engine starts return choke control to run position and apply full throttle the throttle will automatically disengage from the start setting CAUTION Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended This can damage the machine CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance CAUTION Do not put any part of your body in marked area Contact can result in burns to the skin or electrical s
33. n the blade comes e i de NC into contact with a fixed object The i f RU Always wear approved protective blade is capable of amputating an U gloves armor leg Alwavs keep people and animals at least 15 metres from the machine Arrows which show limits for handle positioning Regular cleaning is required Visual check ko Approved eve protection must alwavs be used Alwavs wear approved protective gloves Wear sturdv non slip boots 2 English CONTENTS Contents KEY TO SYMBOLS 100 a 0 ees 2 CONTENTS CONTENTS acredita 3 Note the following before starting 3 INTRODUCTION Dear customer re 4 WHAT IS WHAT What is what on the brush cutter 5 GENERAL SAFETY PRECAUTIONS Important i EE 6 Personal protective equipment 6 Machine s safety equipment rrr 7 Cutting equipment unseren 10 ASSEMBLV Assembling the handlebar and throttle 13 Assembling the cutting equipment 13 Fitting the guard extension 13 Fitting a blade guard grass blade and grass cutter 14 Fitting the blade guard and saw blade 14 Fitting other guards and cutting attachments 15 Adjusting the harness and brush cutter 16 Standard harness A 16 Triobalance harness nennen 16 FUEL HANDLING Fuel safety e
34. ne unless you are able to call for help in the event of an accident 2 Inspect the working area Remove all loose objects such as stones broken glass nails steel wire string etc that could be thrown out or become wrapped around the cutting attachment 3 Do notuse the machine in bad weather such as dense fog heavy rain strong wind intense cold etc Working in bad weather is tiring and often brings added risks such as icy ground unpredictable felling direction etc 8 Keep the cutting attachment below waist level 4 Make sure you can move and stand safely Check the 9 Switch off the engine before moving to another area area around you for possible obstacles roots rocks Fit the transport guard before carrying or transporting branches ditches etc in case you have to move the equipment any distance suddenly Take great care when working on sloping 10 Never put the machine down with the engine running ground unless you have it in clear sight The ABC of clearing e Always use the correct equipment Make sure the equipment is well adjusted e Follow the safety precautions Organise your work carefully e Always use full throttle when starting to cut with the blade e Always use sharp blades e Avoid stones e Control the felling direction take advantage of the 5 Take great care when cutting a tree that is under wind tension A tree that is under tension may spring back to its normal position befor
35. nticlockwise until the cutting attachment stops Then turn adjuster screw A clockwise a further WARNING Mufflers fitted with catalytic 1 2 turn converters get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in burns to the skin Remember the risk of fire WARNING If the idle speed cannot be adjusted so that the cutting attachment stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired Cooling system e Muffler NIG ma To keep the working temperature as low as possible the 10 A machine is equipped with a cooling system CAUTION Some mufflers are fitted with a catalytic converter See chapter on Technical data to see whether your machine is fitted with a catalytic converter The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator The exhaust gases are hot and can contain sparks which may cause fire if directed against dry and combustible material The cooling system consists of 1 Air intake on the starter 2 Cooling fins on the cylinder Some mufflers are equipped with a special spark arrestor 3 Cylinder cover directs cold air over the cylinder screen If your machine has this type of muffler you Clean the cooling system with a brush once a week more should clean the screen at least once a week This is best often
36. oad which can result in serious engine damage e When working at continuous high revs a higher octane rating is recommended Two stroke oil e For best results and performance use HUSQVARNA two stroke engine oil which is specially formulated for our air cooled two stroke engines e Never use two stroke oil intended for water cooled engines sometimes referred to as outboard oil rated TCW e Never use oil intended for four stroke engines Mixing ratio 1 50 2 with HUSQVARNA two stroke oil ers 2 1 2 6 1 2 FUEL HANDLING Mixing Always mix the gasoline and oil in a clean container intended for fuel Always start by filling half the amount of the gasoline to be used Then add the entire amount of oil Mix shake the fuel mixture Add the remaining amount of gasoline Mix shake the fuel mixture thoroughly before filling the machine s fuel tank 2 N W Do not mix more than one month s supply of fuel at a time If the machine is not used for some time the fuel tank should be emptied and cleaned WARNING The catalytic converter muffler gets very hot during and after use This also applies during idling Be aware of the fire hazard especially when working near flammable substances and or vapours Fueling WARNING Taking the following precautions will lessen the risk of fire Mix and pour fuel outdoors where there are no sparks or flames Mix and pour fuel outdoo
37. operator s manual Husqvarna Forest amp Garden recommends that you retain all receipts covering maintenance on your small off road engine but Husqvarna Forest amp Garden cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance e As the small off road engine owner you should however be aware that Husqvarna Forest amp Garden may deny you warranty coverage if your small off road engine or a part has failed due to abuse neglect or improper maintenance or unapproved modifications You are responsible for presenting your small off road engine to a Husqvarna Forest amp Garden distribution center or service center as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty coverage you should contact Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com WARRANTY COMMENCEMENT DATE The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser LENGTH OF COVERAGE Husqvarna Forest amp Garden warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is designed built and equipped so as to conform with all applicable regulations adopted by EPA and CARB and is free from defects in materials and workmanship that causes the failure of a warranted part
38. original positions This movement is controlled by two independent return springs This arrangement means that the throttle control is automatically locked at the idle setting Make sure the throttle control is locked at the idle setting when the throttle lockout is released Press the throttle lockout and make sure it returns to its original position when you release it Check that the throttle control and throttle lockout move freely and that the return springs work properly See instructions under the heading Start Start the machine and apply full throttle Release the throttle and check that the cutting attachment stops and remains at a standstill If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting must English 7 GENERAL SAFETY PRECAUTIONS be checked See instructions under the heading Maintenance Stop switch Use the stop switch to switch off the engine Start the engine and make sure the engine stops when you move the stop switch to the stop setting Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator The guard also protects the operator from accidental contact with the cutting attachment Check that the guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is cracked Always use the recommended guard for the cutting attachment yo
39. portant that the raised section on the drive disc support flange engages correctly in the centre hole of the cutting attachment If the cutting attachment is fitted incorrectly it can result in serious and or fatal personal injury e Align the screw hole in the throttle handle with the hole in the handlebar WARNING Never use a cutting attachment without an approved guard e Refit the screw in the hole in the rear of the throttle See the chapter on Technical data If an handle incorrect or faulty guard is fitted this can Screw the screw through the handle and handlebar cause serious personal injury Tighten it IMPORTANT If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar blade guard and harness Fitting the guard extension gt 6 CAUTIONI The guard extension shall alwavs be fitted when using the trimmer head plastic blades and Fit the mounting components as shown combination guard The guard extension shall always be Loosely tighten the four screws R removed when using the grass blade and combination guard e Put on the harness and hang the machine from the support hook Now make a final adjustment so that the machine is in a comfortable working position when it hangs from the harness e Tighten the knob Enter the guard extension guide in the slot of the combination guard Then click the guard
40. re tightly packed adapt your walking pace to suit If the blade jams in a stem never jerk the machine free If you do this the blade bevel gear shaft or handlebar may be damaged Release the handles grip the shaft with both hands and gently pull the machine free Brush cutting with a saw blade hin stems and brush are mown down Work with a sawing movement swinging sideways e Try to cut several stems in a single sawing movement e With groups of hardwood stems first clear around the group Start by cutting the stems high up around the outside of the group to avoid jamming Then cut the stems to the required height Now try to reach in with the blade and cut from the centre of the group If it is WORKING TECHNIQUES still difficult to gain access cut the stems high up and let them fall This will reduce the risk of jamming Grass clearing using a grass blade Grass blades and grass cutters must not be used on woody stems A grass blade is used for all types of tall or coarse grass The grass is cut down with a sideways swinging movement where the movement from right to left is the clearing stroke and the movement from left to right is the return stroke Let the left hand side of the blade between 8 and 12 o clock do the cutting If the blade is angled to the left when clearing grass the grass will collect in a line which makes it easier to collect e g by raking Try to work rhythmically Stand
41. rs where there are no sparks or flames Do not smoke or place hot objects near fuel Always shut off the engine before refuelling Always stop the engine and let it cool for a few minutes before refuelling When refuelling open the fuel cap slowly so that any excess pressure is released gently Tighten the fuel cap carefully after refuelling Always move the machine away from the refuelling area and source before starting If you have spilled fuel on it Wipe off the spillage and allow remaining fuel to evaporate Clean the area around the fuel cap Contamination in the tank can cause operating problems Ensure that the fuel is well mixed by shaking the container before filling the tank uam Min gt 10ft English 19 STARTING AND STOPPING Check before starting trimmer guard if they have been exposed to impact or are cracked e Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth Discard a blade if cracks are found e Never use the machine without a guard nor with a J defective guard dp ln e All covers must be correctly fitted and undamaged o a pom S before you start the machine Starting and stopping e Check that the support flange is not cracke
42. ructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter Keep the teeth of the blade correctly sharpened Follow our recommendations Also refer to the instructions on the blade packaging Maintain the correct blade setting Follow our instructions and use the recommended file gauge WARNING Always stop the engine before doing any work on the cutting attachment This continues to rotate even after the throttle has been released Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it WARNING Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of blade thrust Cutting equipment Saw blades are intended for cutting fibrous types of wood e Grass blades and grass cutters are intended for cutting coarse grass N L GENERAL SAFETY PRECAUTIONS e Sharpen all edges equally to maintain the balance of the blade General rules Only use cutting attachments with the guards we recommend See the chapter on Technical data IN Keep the teeth of the blade correctiv sharpenedi Follow our instructions and use the recommended file gauge An incorrectiv sharpened or damaged blade increases the risk of accidents 4 Keep the correct setting on the saw blade Follow our instructions and use the recomm
43. slope of the ground whether there are stones hollows etc English 23 WORKING TECHNIQUES Forestry clearing using a saw blade e The risk of blade thrust increases with increasing stem size You should therefore avoid cutting with the area of the blade between 12 o clock and 3 o clock e o fell to the left the bottom of the tree should be pushed to the right Tilt the blade and bring it diagonally down to the right exerting firm pressure At the same time push the stem using the blade guard Cut with the area of the blade between 3 o clock and 5 o clock Apply full throttle before advancing the blade e To fell to the right the bottom of the tree should be pushed to the left Tilt the blade and bring it diagonally up to the right Cut with the area of the blade between 3 o clock and 5 o clock so that the direction of rotation of the blade pushes the bottom of the tree to the left 24 English e To fell a tree forwards the bottom of the tree should be pulled backwards Pull the blade backwards with a quick firm movement Large stems must be cut from two sides First determine which direction the stem will fall Make the first cut on the felling side Then finish cutting the stem from the other side Adjust the cutting pressure to match the size of the stem and the hardness of the wood Small stems require more pressure while large stems require less pressure Q Ea e Ifthe stems a
44. th 15 e Adjust the blade setting This should be 1 mm Trimmer head IMPORTANT Always ensure the trimmer cord is wound tightly and evenly around the drum otherwise the machine will generate harmful vibration e Only use the recommended trimmer heads and trimmer cords These have been tested by the manufacturer to suit a particular engine size This is especially important when a fully automatic trimmer head is used Only use the recommended cutting attachment See the chapter on Technical data Smaller machines generally require small trimmer heads and vice versa This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared e The length of the cord is also important A longer cord requires greater engine power than a shorter cord of the same diameter e Make sure that the cutter on the trimmer guard is intact This is used to cut the cord to the correct length e To increase the life of the cord it can be soaked in water for a couple of days This will make the line tougher so that it lasts longer 12 English ASSEMBLY Assembling the handlebar and Assembling the cutting throttle equipment gt WARNING T A Remove the screw at the rear of the throttle handle Slide the throttle handle onto the right side of the When fitting the cutting attachment it is handlebar see diagram extremely im
45. the Check that the cutting attachment does not rotate atide attachment does not rotate at idle Clean the air filter Replace if necessary mE Check that the guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is cracked XIX x x x Check that the blade is correctly centred is sharp and is not cracked An off centre blade will cause vibration that could result in damage to the machine CC MEN NN the trimmer head if necessary Check thatthe locking nat ot ne cutting equipment stamen coreey X Check hat nuts and ore arg X Check that here are no fuelleaks trom tne engine tank orun Check that the transport guard for the blade is intact and that it can be secured correctly Check the starter and starter cord KE o X Check that the vibration damping elements are not damaged A E MK Clean the outside of the spark plug Remove it and check the electrode gap Adjust the gap to 0 5 mm 20 or replace the spark plug Check X that the spark plug is fitted with a suppressor Clean the machine s cooling system da Clean or replace the spark arrestor screen on the muffler only applies to mufflers without a catalytic converter Clean the outside of the carburettor and the space around it the outside of the carburettor and the Clean the outside of the carburettor and the space around it around it Check that the bevel gear is filled three
46. u are using See chapter on Technical data WARNING Never use a cutting attachment without an approved guard See the chapter on Technical data If an incorrect or faulty guard is fitted this can cause serious personal injury 8 English Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier Using incorrectly wound cord or a blunt or incorrect cutting attachment wrong type or incorrectly filed see instructions under the heading Filing the blade increases the level of vibration The machine s vibration damping system reduces the transfer of vibration between the engine unit cutting equipment and the machine s handle unit Regularly check the vibration damping units for cracks or deformation Ww 535RX 535RXT Check that the vibration damping element is undamaged and securely attached GENERAL SAFETY PRECAUTIONS WARNING Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation Contact your doctor if you experience symptoms of overexposure to vibration Such symptoms include numbness loss of feeling tingling pricking pain loss of strength changes in skin colour or condition These symptoms normally appear in the fingers hands or wrists The risk increases at low temperatures Quick release There is an easily accessible quick rele
47. verns the engine s speed via the throttle control Air and fuel are mixed in the carburetor The air fuel mixture is adjustable Correct adjustment is essential to get the best performance from the machine The setting of the carburetor means that the engine is adapted to local conditions for example the climate altitude fuel and the type of 2 stroke oil e The carburetor has three adjustment controls L Low speed jet H High speed jet T Idle adjustment screw e The Land H jets are used to adjust the supply of fuel to match the rate that air is admitted which is controlled with the throttle If they are screwed clockwise the air fuel ratio becomes leaner less fuel and if they are turned anti clockwise the ratio becomes richer more fuel A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed The T screw regulates the throttle setting at idle speed If the T screw is turned clockwise this gives a higher idle speed turning it anti clockwise gives a lower idle speed Basic setting e The basic carburetor settings are adjusted during testing at the factory The basic setting is richer than the optimal setting and should be maintained for the first few hours the machine is in use The carburettor should then be finely adjusted Fine adjustment should be carried out by a skilled technician CAUTION If the cutting attachment rotates when the engine is Idling the idle adjustment screw
48. warrant failures of warranted parts caused by the use of anon exempted add on or modified part HOW TO FILE A CLAIM If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized servicing dealer or call Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com WHERE TO GET WARRANTY SERVICE Warranty services or repairs are provided through all Husqvarna Forest amp Garden authorized servicing dealers MAINTENANCE REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of the manufacturer MAINTENANCE STATEMENT The owner is responsible for the performance of all required maintenance as defined in the operator s manual 34 English T35 T35x pil T45x T45 00 ZIA IEKON Nie N OE L 901 ww e Z z E 2 7 mm 9 0 m 3 0 mm 7 5 m 3 3 mm 6 0 m Trimmy SII Trimmy SII LLI 15 cm 6 Original instructions 1154017 95
49. when coming into contact with trees and wooden fences l When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head English 25 WORKING TECHNIQUES Cutting The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower Keep the cord parallel to the ground when cutting Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool e Do not allow the trimmer head to constantly come into contact with the ground during normal cutting Constant contact of this type can cause damage and wear to the trimmer head Sweeping The fan effect of the rotating cord can be used for quick and easy clearing up Hold the cord parallel to and above the area to be swept and move the tool to and fro When cutting and sweeping you should use full throttle to obtain the best results 26 English MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions After the engine has used 8 10 tanks of fuel the engine will be run in To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running in period ask your dealer service workshop who will have a rev counter at their disposal to adjust your carburettor Function e The carburetor go
Download Pdf Manuals
Related Search