Husqvarna 327LD Trimmer User Manual
Contents
1. This continues to rotate even after the throttle has been released Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it WARNING A faulty cutting attachment may increase the risk of accidents English 9 GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT Always ensure the trimmer cord is wound tightly and evenly around the drum otherwise the machine will generate harmful vibration e Only use the recommended trimmer heads and trimmer cords These have been tested by the manufacturer to suit a particular engine size This is especially important when a fully automatic trimmer head is used Only use the recommended cutting attachment See the chapter on Technical data e Smaller machines generally require small trimmer heads and vice versa This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared e The length of the cord is also important A longer cord requires greater engine power than a shorter cord of the same diameter e Make sure that the cutter on the trimmer guard is intact This is used to cut the cord to the correct length e To increase the life of the cord it can be soaked in water for a couple of days This will make the line tougher so that it lasts longer 10 English ASSEMBLY Fitting the loop h2. warranty claim Husqvarna Forest amp Garden will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part HOWTO FILE A CLAIM If you have any questions regarding your warranty rights and responsibilities you should contact your nearest authorized servicing dealer or call Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com WHERE TO GET WARRANTY SERVICE Warranty services or repairs are provided through all Husqvarna Forest amp Garden authorized servicing dealers MAINTENANCE REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of the manufacturer MAINTENANCE STATEMENT The owner is responsible for the performance of all required maintenance as defined in the operator s manual English 27 E T35 T35x II 095 106 11079 095 Original instructions 1153293 95
3. a higher engine speed and a rich mixture gives a lower engine speed e The T screw regulates the throttle setting at idle speed If the T screw is turned clockwise this gives a higher idle speed turning it anti clockwise gives a lower idle speed Basic setting e The basic carburetor settings are adjusted during testing at the factory The basic setting is richer than the optimal setting and should be maintained for the first few hours the machine is in use The carburettor should then be finely adjusted Fine adjustment should be carried out by a skilled technician CAUTION If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti clockwise until the cutting attachment stops Adjustment of the idle speed Before any adjustments are made make sure that the air filter is clean and the air filter cover is fitted Adjust the idle speed using the idle adjustment screw T if it is necessary to readjust First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate Then turn the screw anticlockwise until the cutting attachment stops The idle speed is correctly adjusted when the engine will run smoothly in every position The idle speed should also be well below the speed at which the cutting attachment starts to rotate Rec idle speed See the Technical data section WARNING If the idle speed cannot be adjusted so that the cutting attachment
4. also applies at idle speed Contact can result in burns to the skin Remember the risk of fire 20 English Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system f i hy SAI fel n The cooling system consists of 1 Air intake on the starter 2 Fins on the flywheel 3 Cooling fins on the cylinder 4 Cylinder cover directs cold air over the cylinder Clean the cooling system with a brush once a week more often in demanding conditions A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder Spark plug ple The spark plug condition is influenced by e Incorrect carburetor adjustment e An incorrect fuel mixture too much or incorrect type of oil e A dirty air filter These factors cause deposits on the spark plug electrodes which may result in operating problems and starting difficulties MAINTENANCE If the machine is low on power difficult to start or runs poorly at idle speed always check the spark plug first before taking any further action If the spark plug is dirty clean it and check that the electrode gap is 0 020 inch 0 5 mm The spark plug should be replaced after about a month in operation or earlier if necessary CAUTION Always use the recommended spark plug type Use of the wrong spark plug can damage the piston cylinder Check t
5. from defects in materials and workmanship that causes the failure of a warranted part for a period of two years WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty must be performed at no charge to the owner at a warranty station Warranty services or repairs will be provided at all Husqvarna Forest amp Garden distribution centers that are franchised to service the subject engines Throughout the emissions warranty period of two years Husqvarna Forest amp Garden must maintain a supply of warranted parts sufficient to meet the expected demand for such parts WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance schedule is warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part will be repaired or replaced by Husqvarna Forest amp Garden at no cost Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first scheduled replacement point for the part Any warranted part that is not scheduled for replacement as required in the maintenance schedule is warranted for two years If any such part fails during the period of warranty coverage it will be repaired and replaced by Husqvarna Forest amp Garden at no cost Any such part repaired or replaced under the warranty is warra
6. stops contact your dealer service workshop Do not use the machine until it has been correctly adjusted or repaired Muffler CAUTION Some mufflers are fitted with a catalytic converter See chapter on Technical data to see whether your machine is fitted with a catalytic converter The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator The exhaust gases are hot and can contain sparks which may English 19 MAINTENANCE cause fire if directed against dry and combustible material Some mufflers are equipped with a special spark arrestor screen If your machine has this type of muffler you should clean the screen at least once a week This is best done with a wire brush On mufflers without a catalytic converter the screen should be cleaned weekly or replaced if necessary On mufflers fitted with a catalytic converter the screen should be checked and if necessary cleaned monthly If the screen is damaged it should be replaced If the screen is frequently blocked this can be a sign that the performance of the catalytic converter is impaired Contact your dealer to inspect the muffler A blocked screen will cause the machine to overheat and result in damage to the cylinder and piston CAUTION Never use a machine with a defective muffler WARNING Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping This
7. Handle adjustment Drive disc Operator s manual Allen key Locking pin GENERAL SAFETY PRECAUTIONS Important IMPORTANT The machine is only designed for trimming grass The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data Never use the machine if you are tired if you have drunk alcohol or if you are taking medication that could affect your vision your judgement or your co ordination Wear personal protective equipment See instructions under the heading Personal protective equipment Never use a machine that has been modified in any way from its original specification Never use a machine that is faulty Carry out the checks maintenance and service instructions described in this manual Some maintenance and service measures must be carried out by trained and qualified specialists See instructions under the heading Maintenance All covers guards and handles must be fitted before starting Ensure that the spark plug cap and ignition lead are undamaged to avoid the risk of electric shock The machine operator must ensure that no people or animals come closer than 15 metres while working When several operators are working in the same area the safety distance should be at least twice the tree height and no less than 15 metres WARNING This machine produces an electromagnetic field during operation This field may under some circumsta
8. If you need further information please contact your nearest servicing dealer IMPORTANT All servicing and repair work on the machine requires special training This is especially true of the machine s safety equipment If your machine fails any of the checks described below you must contact your service agent When you buy any of our products we guarantee the availability of professional repairs and service Ifthe retailer who sells your machine is not a servicing dealer ask him for the address of your nearest service agent WARNING Never use a machine with faulty safety equipment The machine s safety equipment must be checked and maintained as described in this section If your machine fails any of these checks contact your service agent to get it repaired Throttle lockout The throttle lockout is designed to prevent accidental operation of the throttle control When you press the lock A i e when you grasp the handle it releases the throttle control B When you release the handle the throttle control and the throttle lockout both move back to their original positions This movement is controlled by two independent return springs This arrangement means that the throttle control is automatically locked at the idle setting Make sure the throttle control is locked at the idle setting when the throttle lockout is released Press the throttle lockout and make sure it returns to its original position wh
9. L AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA U S Environmental Protection Agency CARB California Air Resources Board Environment Canada and Husqvarna Forest amp Garden are pleased to explain the emissions control system s warranty on your 2009 and later small off road engine In U S and Canada new equipment that use small off road engines must be designed built and equipped to meet the applicable Federal or Californian stringent anti smog standards Husqvarna Forest amp Garden must warrant the emissions control system on your small off road engine for the period listed below provided there has been no abuse neglect or improper maintenance of your equipment Your emissions control system may include parts such as the carburetor ignition system catalytic converter fuel tank filters and other associated components Also included may be hoses belts connectors sensors and other emission related assemblies Where a warrantable condition exists Husqvarna Forest amp Garden will repair your small off road engine at no cost to you including diagnosis parts and labor MANUFACTURER S WARRANTY COVERAGE The emissions control system is warranted for two years If any emissions related part on your equipment is defective the part will be repaired or replaced by Husqvarna Forest amp Garden OWNER S WARRANTY RESPONSIBILITIES e As the small off road engine owner you
10. Operator s manual 327LS 327LD gt x lt ories Please read the operator s manual carefully and make sure you understand the instructions before using the machine ti A KEY TO SYMBOLS Symbols WARNING Clearing saws brushcutters and trimmers can be dangerous Careless or incorrect use can result in serious or fatal injury to the operator or others It is extremely important that you read and understand the contents of the operator s manual Please read the operator s manual carefully and make sure you understand the instructions before using the machine E Always wear e A protective helmet where there is a risk of falling objects e Approved hearing protection e Approved eye protection Max speed of output shaft rom max 10000 rpm Watch out for thrown objects and ricochets The operator of the machine must ensure while working that no persons or animals come closer than 15 metres Machines fitted with saw blades or grass blades can be thrown violently to the side when the blade comes AN into contact with a fixed object This is A called blade thrust The blade is 1 capable of amputating an arm or leg Always keep people and animals at least 15 metres from the machine Arrows which show limits for handle positioning Always wear approved protective gloves Wear sturdy non slip boots 2 English Only use non metallic flexible cutting attachments e trimm
11. a to be cut W NW WMA YA The cord can easily remove grass and weeds up against walls fences trees and borders however it can also damage sensitive bark on trees and bushes and damage fence posts Reduce the risk of damaging plants by shortening the cord to 10 12 cm and reducing the engine speed Clearing The clearing technique removes all unwanted vegetation Keep the trimmer head just above the ground and tilt it Let the end of the cord strike the ground around trees posts statues and the like CAUTION This technique increases the wear on the cord An daran 7 The cord wears quicker and must be fed forward more often when working against stones brick concrete metal fences etc than when coming into contact with trees and wooden fences When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head 18 English The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower Keep the cord parallel to the ground when cutting Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool WE IM Do not allow the trimmer head to constantly come into contact with the ground during normal cutting Constant contact of this type can cause damage and wear to the trimmer head Sweeping The fan effect of the rotating cord can be used for quick and easy
12. ality motor driven products for forestry and gardening as well as for building and construction industry Your purchase gives you access to professional help with repairs and service whenever this may be necessary If the retailer who sells your machine is not one of our authorized dealers ask for the address of your nearest servicing dealer It is our wish that you will be satisfied with your product and that it will be your companion for a long time Think of this operators manual as a valuable document By following its content using service maintenance etc the life span and the second hand value of the machine can be extended If you ever lend or sell this machine make sure that the borrower or buyer gets the operator s manual so they will also know how to properly maintain and use it Thank you for using a Husqvarna product Husqvarna AB has a policy of continuous product development and therefore reserves the rightto modify the design and appearance of products without prior notice For customer assistance contact us at our website www usa husqvarna com 4 English What is what Trimmer head Grease filler cap bevel gear Bevel gear Cutting attachment guard Shaft Shaft coupling 327LDx Loop handle ON DOA OD Throttle control 9 Stop switch 10 Throttle lockout 11 Spark plug cap and spark plug WHAT IS WHAT Cylinder cover Starter handle Fuel tank Air filter cover Air purge Choke control
13. andle Clip the loop handle onto the shaft Note that the loop handle must be fitted between the arrows on the shaft Slide the spacer into the slot in the loop handle Fit the nut knob and screw Do not overtighten Now adjust the trimmer to give a comfortable working position Tighten the bolt knob Assembling and dismantling the two piece shaft 327LDx Assembly Loosen the coupling by turning the knob Align the tab of the attachment A with the arrow on the coupling B Push the attachment into the coupling until the attachment snaps into place e Before using the unit tighten the knob securely Dismantling e Loosen the coupling by turning the knob at least 3 times e Push and hold the button C While securely holding the engine end pull the attachment straight out of the coupling English 11 ASSEMBLY Assembling the cutting equipment N WARNING When fitting the cutting attachment it is extremely important that the raised section on the drive disc support flange engages correctly in the centre hole of the cutting attachment If the cutting attachment is fitted incorrectly it can result in serious and or fatal personal injury WARNING Never use a cutting attachment without an approved guard See the chapter on Technical data If an incorrect or faulty guard is fitted this can cause seriou
14. are responsible for performance of the required maintenance listed in your operator s manual Husqvarna Forest 8 Garden recommends that you retain all receipts covering maintenance on your small off road engine but Husqvarna Forest amp Garden cannot deny warranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance e As the small off road engine owner you should however be aware that Husqvarna Forest amp Garden may deny you warranty coverage if your small off road engine or a part has failed due to abuse neglect or improper maintenance or unapproved modifications e You are responsible for presenting your small off road engine to a Husqvarna Forest amp Garden distribution center or service center as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty coverage you should contact Husqvarna Forest amp Garden at 1 800 487 5951 or visit www usa husqvarna com 26 English WARRANTY COMMENCEMENT DATE The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser LENGTH OF COVERAGE Husqvarna Forest amp Garden warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is designed built and equipped so as to conform with all applicable regulations adopted by EPA and CARB and is free
15. cess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine Never use common engine oil This would drain through the filter quite quickly and collect in the bottom English 21 MAINTENANCE Bevel gear p gt The bevel gear is filled with the right quantity of grease at the factory However before using the machine you should check that the bevel gear is filled three quarters full with grease Use HUSQVARNA special grease The grease in the bevel gear does not normally need to be changed except if repairs are carried out CAUTION Use only HUSQVARNA replacement parts Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others Your warranty does not cover damage or liability caused by the use of accessories and or attachments not specifically recommended by HUSQVARNA 22 English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine Most of the items are described in the Maintenance section Maintenance pally meek monthly maintenance maintenance maintenance Make sure the throttle trigger lock and the throttle function X correctly from a safety point of view Check that the stop switch works correctly x Il Check that the cutting attachment does not rotate at idle ES O Clean the air filter Replace if necessary Check that t
16. clearing up Hold the cord parallel to and above the area to be swept and move the tool to and fro When cutting and sweeping you should use full throttle to obtain the best results MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions After the engine has used 8 10 tanks of fuel the engine will be run in To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running in period ask your dealer service workshop who will have a rev counter at their disposal to adjust your carburettor Function e The carburetor governs the engine s speed via the throttle control Air and fuel are mixed in the carburetor The air fuel mixture is adjustable Correct adjustment is essential to get the best performance from the machine e The setting of the carburetor means that the engine is adapted to local conditions for example the climate altitude fuel and the type of 2 stroke oil e The carburetor has three adjustment controls L Low speed jet H High speed jet T Idle adjustment screw e The Land H jets are used to adjust the supply of fuel to match the rate that air is admitted which is controlled with the throttle If they are screwed clockwise the air fuel ratio becomes leaner less fuel and if they are turned anti clockwise the ratio becomes richer more fuel A lean mixture gives
17. e starter cord around your hand Repeat pulling the cord until the engine starts When the engine starts return choke control to run position and English 15 STARTING AND STOPPING apply full throttle the throttle will automatically disengage from the start setting CAUTION Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended This can damage the machine CAUTION Do not put any part of your body in marked area Contact can result in burns to the skin or electrical shock if the spark plug cap has been damaged Always use gloves Do not use a machine with damaged spark plug cap Stopping Stop the engine by switching off the ignition CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance 16 English WORKING TECHNIQUES General working instructions 6 Always hold the machine with both hands Hold the machine on the right side of your body IMPORTANT This section takes up the basic safety precautions for working with a trimmer If you encounter a situation where you are uncertain how to proceed you should ask an expert Contact your dealer or your service workshop Avoid all usage which you consider to be beyond your capability You must understand the difference b
18. e felling may remain so for a while afterwards You direction etc could get burnt if you touch it 4 Make sure you can move and stand safely Check the area around you for possible obstacles roots rocks WARNING Watch out for thrown objects branches ditches etc in case you have to move Always wear approved eye protection suddenly Take great care when working on sloping Never lean over the cutting attachment ground guard Stones rubbish etc can be thrown up into the eyes causing blindness or serious injury Keep unauthorised persons at a distance Children animals onlookers and helpers should be kept outside the safety zone of 15 m Stop the machine immediately if anyone approaches Never swing the machine around without first checking behind you to make sure no one is within the safety zone 5 Keep a good balance and a firm foothold English 17 WORKING TECHNIQUES Cutting Basic working techniques Always slow the engine to idle speed after each working operation Long periods at full throttle without any load on the engine can lead to serious engine damage WARNING Sometimes branches or grass get caught between the guard and cutting attachment Always stop the engine before cleaning Grass trimming with a trimmer head Trimming Hold the trimmer head just above the ground at an angle It is the end of the cord that does the work Let the cord work at its own pace Never press the cord into the are
19. e recommended for use in combination with the specified power heads and have been evaluated to applicable ISO and EN safety requirement standards by the Swedish Machinery Testing Institute 24 English TECHNICAL DATA Hedge trimmer attachment with shaft HA 110 537 19 66 01 Hedge trimmer attachment with shaft HA 850 537 19 66 02 The accessories have been developed mainly for the Husqvarna 125LD trimmer but can also be used in combination with the specified power heads and have been evaluated to applicable ISO and EN safety requirement standards by the Swedish Machinery Testing Institute Powerhead model model Accessories a attachment CAC 952 71 19 07 Edger attachment EAC 952 71 19 08 327LDx Pole saw attachment PAC 952 71 19 10 Blower attachment BAC 952 71 19 11 Hedge trimmer attachment HAC 952 71 19 21 The accessories used in combination with the specified power heads have been evaluated to ANSI B175 3 2003 Grass Trimmers and Brushcutters Safety Requirements These combinations have been evaluated by Underwriters Laboratories Inc UL and are consequently UL listed Arbor shaft thread M10 R aaa Tricut 300 mm Separate Plastic blades blades have part number 503 93 42 02 327LDx 531 01 77 18 T25 2 0 2 7 mm cord 503 93 42 02 503 97 71 01 Trimmer head S35 2 4 3 0 mm cord 503 93 42 02 503 97 71 01 T35 2 4 3 0 mm cord 503 93 42 02 503 97 71 01 English 25 FEDERA
20. east 87 octane RON MON 2 If your machine is equipped with a catalytic converter see chapter on Technical data always use a good quality unleaded gasoline oil mixture Leaded gasoline will destroy the catalytic converter Use low emission gasoline also known as alkylate gasoline if it is available This engine is certified to operate on unleaded gasoline e The lowest recommended octane grade is 87 RON MON 2 If you run the engine on a lower octane grade than 87 so called knocking can occur This gives rise to a high engine temperature and increased bearing load which can result in serious engine damage e When working at continuous high revs a higher octane rating is recommended Two stroke oil e For best results and performance use HUSQVARNA two stroke engine oil which is specially formulated for our air cooled two stroke engines e Never use two stroke oil intended for water cooled engines sometimes referred to as outboard oil rated TCW e Never use oil intended for four stroke engines e Mixing ratio 1 50 2 with HUSQVARNA two stroke oil Two stroke oil litre Gasoline litre 2 1 50 2 1 2 English 13 FUEL HANDLING Mixing Fueling e Always mix the gasoline and oil in a clean container intended for fuel e Always start by filling half the amount of the gasoline to be used Then add the entire amount of oil Mix shake the fuel mixture Add the remaining amount of WARNING Taking the
21. en you release it Check that the throttle control and throttle lockout move freely and that the return springs work properly See instructions under the heading Start Start the machine and apply full throttle Release the throttle and check that the cutting attachment stops and remains at a standstill If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting must English 7 GENERAL SAFETY PRECAUTIONS be checked See instructions under the heading Maintenance Stop switch Use the stop switch to switch off the engine Start the engine and make sure the engine stops when you move the stop switch to the stop setting Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator The guard also protects the operator from accidental contact with the cutting attachment Check that the guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is cracked Always use the recommended guard for the cutting attachment you are using See chapter on Technical data WARNING Never use a cutting attachment without an approved guard See the chapter on Technical data If an incorrect or faulty guard is fitted this can cause serious personal injury 8 English Vibration damping system Your machine is equipped with a vibration damping system that is designed t
22. er heads with trimmer cord Other symbols decals on the machine refer to special certification requirements for certain markets The engine is switched off by moving the stop switch to the stop position CAUTION The stop switch automatically returns to the start position In order to prevent unintentional starting the spark plug cap must be removed from the spark plug when assembling checking and or performing maintenance Always wear approved protective gloves Regular cleaning is required Visual check Approved eye protection must always be used The engine exhaust from this product contains chemical known to the State of California to cause cancer birth defects or other reproductive harm CONTENTS Contents Note the following before KEY TO SYMBOLS starting SU TOO 2 Please read the operator s manual carefully CONTENTS SR Maintenance replacement or repair of the emission Contents ee ee 3 control devices and system may be performed by any Note the following before starting 3 nonroad engine repair establishment or individual INTRODUCTION A 4 WARNING Long term exposure to noise WHAT IS WHAT can result in permanent hearing impairment So always use approved What IS what A Ea 5 hearing protection GENERAL SAFETY PRECAUTIONS Important re es a a 6 WARNING Under no circumstances may Personal protective equipment IIA ARS 6 the design of the machi
23. etween forestry clearing grass clearing and grass trimming before use Basic safety rules AO 1 Look around you 7 Keep the cutting attachment below waist level 8 The engine must be switched off before moving e To ensure that people animals or other things cannot 9 Never put the machine down with the engine running affect your control of the machine To ensure that people animals etc do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment CAUTION Do not use the machine unless you are able to call for help in the event of an accident unless you have it in clear sight WARNING Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is running or the cutting equipment is rotating as this can result in serious 2 Inspect the working area Remove all loose objects cue i i injury such as stones broken glass nails steel wire string etc that could be thrown out or become wrapped Stop the engine and cutting equipment around the cutting attachment before you remove material that has 3 Do not use the machine in bad weather such as wound around the blade shaft as dense fog heavy rain strong wind intense cold etc otherwise there is a risk of injury The Working in bad weather is tiring and often brings bevel gear can get hot during use and added risks such as icy ground unpredictabl
24. following gasoline precautions will lessen the risk of fire e Mix shake the fuel mixture thoroughly before filling the machine s fuel tank Do not smoke or place hot objects near fuel Always shut off the engine before refuelling Always stop the engine and let it cool for a few minutes before refuelling When refuelling open the fuel cap slowly so that any excess pressure is released gently Tighten the fuel cap carefully after refuelling Always move the machine away from the refuelling area before starting e Do not mix more than one month s supply of fuel at a ge im e Clean the area around the fuel cap Contamination in PE the tank can cause operating problems e If the machine is not used for some time the fuel tank should be emptied and cleaned e Ensure that the fuel is well mixed by shaking the container before filling the tank WARNING The catalytic converter muffler gets very hot during and after use This also applies during idling Be aware of the fire hazard especially when working near flammable substances and or vapours 14 English STARTING AND STOPPING Starting and stopping Check before starting e Check that the support flange is not cracked due to fatigue or due to being tightened too much Discard the support flange if it is cracked e Ensure the locking nut has not lost its captive force The nut lock should have a locking force of at least 1 5 Nm The tighteni
25. hat the spark plug is fitted with a suppressor Two piece shaft 327LDx pe The drive shaft end in the lower shaft should be lubricated with grease every 30 hours There is a risk that the drive shaft ends splined coupling on models with two piece shafts will seize if they are not lubricated regularly Air filter gt The air filter must be regularly cleaned to remove dust and dirt in order to avoid e Carburettor malfunctions e Starting problems e Loss of engine power e Unnecessary wear to engine parts e Excessive fuel consumption conditions are exceptionally dusty Cleaning the air filter Remove the air filter cover and take out the filter Wash it clean in warm soapy water Ensure that the filter is dry before refitting it An air filter that has been in use for a long time cannot be cleaned completely The filter must therefore be replaced with a new one at regular intervals A damaged air filter must always be replaced If the machine is used in dusty conditions the air filter should be soaked in oil See instructions under the heading Oiling the air filter Oiling the air filter Always use HUSQVARNA filter oil art no 531 00 92 48 The filter oil contains a solvent to make it spread evenly through the filter You should therefore avoid skin contact Put the filter in a plastic bag and pour the filter oil over it Knead the plastic bag to distribute the oil Squeeze the ex
26. he guard is undamaged and not cracked Replace the guard if it has been exposed to impact or is cracked Check that the trimmer head is undamaged and not cracked X Replace the trimmer head if necessary Check that nuts and screws are tight X a EEE Zu EEE Check that there are no fuel leaks from the engine tank or fuel X lines Check the starter and starter cord Check that the vibration damping elements are not damaged PK Clean the outside of the spark plug Remove it and check the electrode gap Adjust the gap to 0 5 mm 20 or replace the X spark plug Check that the spark plug is fitted with a suppressor Clean or replace the spark arrestor screen on the muffler only X applies to mufflers without a catalytic converter Clean the outside of the carburettor and the space around it O E Check that the bevel gear is filled three quarters full with X lubricant Fill if necessary using special grease Check the fuel filter from contamination and the fuel hose from X cracks or other defects Replace if necessary Check the clutch clutch springs and the clutch drum for wear X Replace if necessary by an autorized service workshop Replace the spark plug Check that the spark plug is fitted with a X suppressor o Check and clean the spark arrestor screen on the muffler only applies to mufflers fitted with a catalytic converter English 23 TECHNICAL DATA Technical data Motor Cylinder displacement c
27. nces interfere with active or passive medical implants To reduce the risk of serious or fatal injury we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine WARNING Running an engine in a confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning WARNING Never allow children to use or be in the vicinity of the machine As the machine is equipped with a spring loaded stop switch and can be started by low speed and force on the starter handle even small children under some circumstances can produce the force necessary to start the machine This can mean a risk of serious personal injury Therefore remove the spark plug cap when the machine is not under close supervision 6 English Personal protective equipment IMPORTANT A clearing saw brushcutter or trimmer can be dangerous if used incorrectly or carelessly and can cause serious or fatal injury to the operator or others lt is extremely important that you read and understand the contents of this operator s manual You must use approved personal protective equipment whenever you use the machine Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen Ask your dealer for help in choosing the right equipment WARNING Listen out for warning signals or shou
28. ne be modified Machine s safety equipment ccccooccccnnccnnnncnnnnnns 7 without the permission of the Cutting EQUIPMENT ac a tenis 9 manufacturer Always nz genuine ASSEMBLY accessories Non authorized modifications and or accessories can Fitting the loop handle moscada riicandss 11 result in serious personal injury or the Assembling and dismantling the two piece shaft death of the operator or others ENA EDI E E E EE EEE ecedasseeee 11 Your warranty may not cover damage or Assembling the cutting equipment rk 12 liability caused by the use of non Fitting the trimmer guard and trimmer head 12 authorized accessories or replacement FUEL HANDLING parts Fuel safety caracol 13 FUGI nee een 13 WARNING A clearing saw brushcutter Pr 116 eese E 14 or trimmer can be dangerous if used STARTING AND STOPPING incorrectly or carelessly and can cause serious or fatal injury to the operator or Check before starting daa 15 others It is extremely important that you Starting and Stopping unsere 15 read and understand the contents of this WORKING TECHNIQUES operator s manual General working instructions s s s 17 MAINTENANCE EMISSION CONTROL INFORMATION N A A 19 Husqvarna IA A 19 HUSQVARNA AB HUSKVARNA SWEDEN iit Cooling SyYStem nenne een 20 THIS ENGINE MEETS US EPA AND CALIFORNIA Spak i 20 EXH EVP REGS FOR SORE REFER TO OPERATOR S PATRIO ensure MANUAL FOR MAINTENANCE SPECIFICATIONS AND Two piece shaft 327LDX cooococcccoccccoco
29. ng torque of the locking nut should be 35 50 Nm WARNING The complete clutch cover and shaft must be fitted before the machine is started otherwise the clutch can come loose and cause personal injury Always move the machine away from the refuelling area before starting Place the machine on a flat surface Ensure the cutting attachment cannot come into contact with any object Make sure no unauthorised persons are in the working area otherwise there is a risk of serious personal injury The safety distance is 15 metres Starting Primer bulb Press the air purge repeatedly until fuel begins to fill the bulb The bulb need not be completely filled e Check that the trimmer head and trimmer guard are not damaged or cracked Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked e Never use the machine without a guard nor with a defective guard All covers must be correctly fitted and undamaged before you start the machine WARNING When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately Hold the body of the machine on the ground using your left hand CAUTION Not with your foot Grip the starter handle slowly pull out the cord with your right hand until you feel some resistance the starter pawls grip now quickly and powerfully pull the cord Never wrap th
30. noccnoonononnonos 21 ADJUSTMENTS EMISSONS COMPLIANCE PERIOD J Air filter A RRA A AN 21 The Emissions Compliance Period referred to on the Maintenance schedule e eset eee 23 Emission Compliance label indicates the number of TECHNICAL DATA operating hours for which the engine has been shown to Technical data ecsheeccetice ts LEIDER PREHEEEUUNENLECEREREN 24 meet Federal and Californian emissions requirements FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS 26 English 3 INTRODUCTION Dear customer Congratulations on your choice to buy a Husqvarna product Husqvarna is based on a tradition that dates back to 1689 when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River for production of muskets The location was logical since water power was harnessed from the Huskvarna River to create the water powered plant During over 300 years of continuous operation the Husqvarna factory has produced a lot of different products from wood stoves to modern kitchen appliances sewing machines bicycles motorcycles etc In 1956 the first motor driven lawn mowers appeared followed by chain saws in 1959 and it is within this area Husqvarna is working today Today Husqvarna is one of the leading manufacturers in the world of forest and garden products with quality as our highest priority We develop manufacture and market high qu
31. nted for the remaining warranty period Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years A statement in such written instructions to the effect of repair or replace as necessary will not reduce the period of warranty coverage Any such part repaired or replaced under warranty will be warranted for the remaining warranty period DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station CONSEQUENTIAL DAMAGES Husqvarna Forest amp Garden is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe airfilter holder and carburetor bolts Airfilter and fuelfilter covered up to maintenance schedule Spark Plug covered up to maintenance schedule Ignition Module Muffler with catalytic converter NO 0 Fuel tank WHAT IS NOT COVERED All failures caused by abuse neglect or improper maintenance are not covered ADD ON OR MODIFIED PARTS Add on or modified parts that are not exempted by CARB or EPA may not be used The use of any non exempted add on or modified parts will be grounds for disallowing a
32. o reduce vibration and make operation easier Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration See instructions under the heading Cutting equipment The machine s vibration damping system reduces the transfer of vibration between the engine unit cutting equipment and the machine s handle unit Regularly check the vibration damping units for cracks or deformation Check that the vibration damping element is undamaged and securely attached WARNING Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation Contact your doctor if you experience symptoms of overexposure to vibration These symptoms include numbness loss of feeling tingling pricking pain loss of strength changes in skin colour or condition These symptoms normally appear in the fingers hands or wrists Muffler The muffler is designed to keep noise levels to aminimum and to direct exhaust fumes away from the user A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases GENERAL SAFETY PRECAUTIONS N WARNING Bear in mind that In countries that have a warm and dry climate there is a significant risk of fire We therefore fit certain mufflers with a spark arrestor screen Check whether the muffler on your machine is fitted with this kind of screen For mufflers it is very important that you foll
33. ow the instructions on checking maintaining and servicing your machine Never use a machine that has a faulty muffler Regularly check that the muffler is securely attached to the machine If the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly A blocked screen will cause the engine to overheat and may lead to serious damage WARNING Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping This also applies at idle speed Contact can result in burns to the skin Remember the risk of fire WARNING The inside of the muffler contain chemicals that may be carcinogenic Avoid contact with these elements in the event of a damaged muffler The exhaust fumes from the engine are hot and may contain sparks which can start a fire Never start the machine indoors or near combustible material Cutting equipment This section describes how to choose and maintain your cutting equipment in order to e Reduce the risk of blade thrust e Obtain maximum cutting performance e Extend the life of cutting equipment IMPORTANT Only use cutting attachments with the guards we recommend See the chapter on Technical data Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter WARNING Always stop the engine before doing any work on the cutting attachment
34. ring the machine for long periods the fuel tank must be emptied Contact your local gas station to find out where to dispose of excess fuel e Ensure the machine is cleaned and that a complete service is carried out before long term storage e The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage e Secure the machine during transport e In order to prevent unintentional starting of the engine the spark plug cap must always be removed during long term storage if the machine is not under close supervision and when performing all service measures WARNING Take care when handling fuel Bear in mind the risk of fire explosion and inhaling fumes A Fuel CAUTION The machine is equipped with a two stroke engine and must always been run using a mixture of gasoline and two stroke engine oil It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained When mixing small amounts of fuel even small inaccuracies can drastically affect the ratio of the mixture WARNING Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin For this reason observe caution when handling fuel and make sure there is adequate ventilation Gasoline gt 0 CAUTION Always use a quality gasoline oil mixture with an octane rating of at l
35. s personal injury Fitting the trimmer guard and trimmer head Also e Fit the correct trimmer guard A for use with the trimmer head Hook the trimmer guard combination guard onto the fitting on the shaft and secure with the bolt L A e Fit the drive disc B on the output shaft e Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing e Insert the locking pin C in the hole to lock the shaft 12 English Screw on the trimmer head plastic blades H in the opposite direction to the direction of rotation To dismantle follow the instructions in the reverse order FUEL HANDLING Fuel safety Never start the machine 1 If you have spilled fuel on it Wipe off the spillage and allow remaining fuel to evaporate 2 If you have spilled fuel on yourself or your clothes change your clothes Wash any part of your body that has come in contact with fuel Use soap and water 3 If the machine is leaking fuel Check regularly for leaks from the fuel cap and fuel lines Transport and storage e Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames for example from electrical machinery electric motors electrical relays switches or boilers e When storing and transporting fuel always use approved containers intended for this purpose e When sto
36. ts when you are wearing hearing protection Always remove your hearing protection as soon as the engine stops HELMET A protective helmet where there is a risk of falling objects HEARING PROTECTION Wear hearing protection that provides adequate noise reduction EYE PROTECTION Always wear approved eye protection If you use a visor then you must also wear approved protective goggles Approved protective goggles must comply with standard ANSI Z87 1 in the USA or EN 166 in EU countries GLOVES Gloves should be worn when necessary e g when fitting cutting attachments GENERAL SAFETY PRECAUTIONS BOOTS Wear sturdy non slip boots CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches Always wear heavy long pants Do not wear jewellery shorts sandals or go barefoot Secure hair so it is above shoulder level FIRST AID KIT Always have a first aid kit nearby IN Machine s safety equipment This section describes the machine s safety equipment its purpose and how checks and maintenance should be carried out to ensure that it operates correctly See the What is what section to locate where this equipment is positioned on your machine The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and or repairs are not carried out professionally
37. u in cm Cylinder bore inch mm Stroke inch mm Idle speed rpm Recommended max speed rpm Speed of output shaft rpm Max engine output acc to ISO 8893 kW rpm Catalytic converter muffler Speed regulated ignition system Ignition system Spark plug Electrode gap inch mm Fuel and lubrication system Fuel tank capacity US pint litre Weight Weight without fuel cutting attachment and guard Lbs kg Sound levels see note 1 Equivalent sound pressure level at the operator s ear measured according to EN ISO 11806 and ISO 22868 dB A Equipped with trimmer head original Vibration levels see note 2 Equivalent vibration levels Apy eg at handles measured according to EN ISO 11806 and ISO 22867 m s Equipped with trimmer head original left right NOTE This spark ignition system complies with the Canadian standard ICES 002 327LDx 1 50 24 5 1 34 34 1 06 27 2700 11000 11700 8300 0 9 8400 Yes Yes Champion RCJ 6Y 0 02 0 5 1 06 0 5 11 29 94 2 9 3 4 327LS 1 50 24 5 1 34 34 1 06 27 2700 11000 11700 8300 0 9 8400 Yes Yes Champion RCJ 6Y 0 02 0 5 1 06 0 5 10 6 4 8 98 4 2 3 1 Note 1 Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion standard deviation of 1 dB A Note 2 Reported data for equivalent vibration level has a typical statistical dispersion standard deviation of 1 m s The accessories ar
Download Pdf Manuals
Related Search