Hunter Fan 42823-01 Fan User Manual
Contents
1. A Steps 7 5 7 6 Lower Switch Housing Plug T Connector Detail Housing Assembly Screw 7 e Completing Your Installation With a Bowl Light Fixture Continued Installing the Glass Bowl 7 7 First install B10 candelabra bulbs 60 Watt Maximum into the sockets 7 8 Thread the light and fan pull chains through the hole in the center of the glass bowl Then thread the light pull chain through the hole in the center of the cover plate 7 9 Thread the fan pull chain through the grommet hole in the side of the cover plate 7 10 Place the cover plate up against the glass bowl Align the holes in the cover plate and glass bowl 7 11 Thread the light pull chain through the finial and screw the finial onto the threaded rod end until tight 7 12 Attach the extra pull chains included to the light and fan pull h the plastic break tor Y find th C ains using e pias iC rea away connec ans ou may n e Light Bulbs plastic breakaway connector on the N a i B10 j _ Candelabra Base 60 Watt Maximum R _ _ Metal Rod r a Metal Disk end of the extra chain Glass Bowl a Cover Plate Breakaway wy Finial Connector ee 12 42823 01 02 17 10 Hunter Fan Company 8 Operating and Cleaning Your Ceiling Fan 8 1 Turn on electrical power to the fan 8 2 The fan pull chain controls power to the fan The pull chain has four settings in sequence High Me2. For Your Records and Warranty Assistance For reference also attach your receipt or a copy of your receipt to the manual i ode Type 2A Models Owner s Guide and Installation Manual SINCE 1886 Form 42823 01 20100217 2010 Hunter Fan Co Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION SAVE THESE INSTRUCTIONS e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the Table Of Contents support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan 2 Installing the Hanger Bracket disconnect the power by turning off the circuit breakers to the 3 Assembling and Hanging the Fan 6 outlet box and associated wall switch location If you cannot lock
3. the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 6 Assembling the Blades codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls 1 e Getting Ready 4 Wiring the Fan 5 e Installing the Motor Housing 7 Completing Your Installation With a Bowl Light Fixture 8 Operating and Cleaning Your Ceiling 9 e Troubleshooting 2010 Hunter Fan Company 2 42823 01 02 17 10 Hunter Fan Company Mounting and Optional Accessories Vy Vy Understanding Mounting Hunter s patented mounting system provides you maximum ease in installing your fan This fan was designed to be mounted only on flat ceilings and can be used on ceilings less than 8 feet high Considering Optional Accessories Low Profile at Mounting Style Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included
4. alling the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 4 Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped 42823 01 02 17 10 Hunter Fan Company 2 Installing the Hanger Bracket A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel 2 1 2 2 2 3 2 4 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Partially install two canopy screws in the holes on each end of the hanger bracket as shown in the figure to the right Your fan comes with four mounting isolators Position the isolators between the hanger bracket and ceiling by inserting the raised areas on each isolator into the holes in the hanger bracket Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket Align the slot
5. dium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 8 3 The light pull chain controls the power to the light fixture The In warm weather use chain has two settings ON and OFF downward air flow pattern 8 4 Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft 8 5 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish 8 6 Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the In cold weather use upward same manner as the fan finish air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the revers
6. dlett Farms Pkwy 400 Memphis Tennessee 38016 14 42823 01 02 17 10 Hunter Fan Company
7. g must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 4 1 Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location 4 2 To connect the wires hold the bare metal leads together and place a wire connector over them then twist clockwise until tight A CAUTION Be sure no bare wire or wire strands are visible after making connections 4 3 Connect the wires as follows e The green or bare ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the fan e The white common power wire from the ceiling to the white wire from the fan e The black power wire from the ceiling to the black wire from the fan e The black white wire from the fan to the black white wire from the ceiling 4 4 Push all wires and wire connectors back through the ceiling plate hole Wire into the outlet box Connector 7 42823 01 02 17 10 Hunter Fan Company 5 Installing the Motor Housing 5 1 Place the fan housing over the motor Step 5 1 5 2 Align the keyholes in the fan housing with the two partially installed canopy screws in the hanger bracket Rotate the fan housing to situate the screws in the narrow ends of the keyholes 5 3 Install the two remaining canopy screws into the holes in the fan housing and into the hanger bracke
8. ing switch on the fan to the opposite position Restart fan Reversing Switch 13 42823 01 02 17 10 Hunter Fan Company 9 Troubleshooting Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Tighten the blade screws until snug 3 Check to see if the blade is cracked If so replace all the blades 4 Change to an approved speed control 5 Be sure that the glass is secure 6 Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws Problem Lights dim when turned on or do not turn on 1 Check to make sure wattage of light bulbs installed match the specifications on the light socket If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 7130 Goo
9. of the housing 7 3 Align the keyhole slots in the housing with the housing assembly screws 7 4 Turn the housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots Install the remaining screw into the housing Tighten all three Steps 7 1 7 3 screws firmly Housing t er A CAUTION Make sure the upper switch housing is securely SS oy ae attached to the switch housing mounting plate Failure to properly Housing attach and tighten all three assembly screws could result in the switch housing and light fixture falling 10 42823 01 02 17 10 Hunter Fan Company 7 5 To attach the lower switch housing connect the upper plug 7 6 7 e Completing Your Installation With a Bowl Light Fixture Continued connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws lI 42823 01 02 17 10 Hunter Fan Company Plug Connector
10. t Securely tighten all screws 8 42823 01 e 02 17 10 Hunter Fan Company 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 Remove the blade mounting screws and rubber shipping bumpers from the motor Note Some blade mounting screws are installed in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Use with grommet ews Use without grommet Blade Mounting Screw 42823 01 02 17 10 Hunter Fan Company 7 Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly A WARNING Use only the light fixture supplied with this fan model 7 1 To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate 7 2 Feed the upper plug connector through the center opening
11. ted holes in the hanger bracket with the pilot holes you drilled in the wood support structure Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 wood screws and pass the screws through the slotted holes in the hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw EEE thant 5 42823 01 02 17 10 Hunter Fan Company Hanger Bracket a Canopy Screw Isolator Step 2 2 Canopy Screw Steps 2 4 2 6 3 Assembling and Hanging the Fan Step 3 1 Motor 3 1 Position the square hanger so that the green ground wire attached to the square faces out of the large opening in the metal bracket 3 2 Holding the wires out of the way lift the motor assembly and place the square hanger into the opening in the ceiling plate A WARNING Make sure the square hanger can not rotate in the metal bracket Failure to do so could result in the fan falling 3 3 Install two locking screws through the holes in the side of the metal bracket to secure the square hanger Assembly Green Ground Wire Step 3 2 Green Ground Wire Locking Screw 6 42823 01 02 17 10 Hunter Fan Company 4 Wiring the Fan All wirin
12. with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls Low Profile Mounting fits close to the ceiling recommended for ceilings less A CAUTION To reduce the risk of than 8 feet high personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied 3 42823 01 02 17 10 Hunter Fan Company l Getting Ready To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip recommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin inst
Download Pdf Manuals
Related Search