Hunter Fan 42737-01 Fan User Manual
Contents
1. installation and operation manual for Hunter Ceiling Fans 42737 01 11 14 06 Welcome For Your Records and Warranty Assistance Model Name Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual Table of Contents 1 Getting Ready 2 Installing the Ceiling Plate 3 e Assembling and Hanging the Fan 4 Wiring the Fan 5 Installing the Canopy and Canopy Trim Ring 6 Assembling the Blades 7 ICompleting Your Installation With or Without the Light Kit 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings Read this entire manual carefully before beginning installation Save these instructions Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the support structure of the build2. 1 Tighten the blade bracket screws until snug Tighten the blade screws until snug Check to see if the blade is cracked If so replace all the blades Change to an approved speed control Be sure that the glass is secure Go i KR W NY Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 42737 01 11 14 06 9 Troubleshooting Hunter Fan Company 15
3. and an 7 6 To attach the lower switch housing connect the upper plug optional switch housing cap and plug button This feature gives you the connector from the motor to the lower plug connector in the option of installing the fan with OR without the included light fixture lower switch housing assembly The steps below direct you whether or not you are installing a light l P y y 5a 118 Note Both plug connectors are polarized and will only fit together fixture Plug one way Make sure the connectors are properly aligned before FN eh he i WARNING Use only the light fixture supplied with this fan model connecting them Incorrect connection could cause improper _ operation and damage to the producc 7 1 To attach the upper switch housing partially install two 6 32 x 7 Place the itch housi bl th itch 3 8 housing assembly screws into the switch housing mounting AE HR Ses eek Cn DFSIR 2 scm Ove RH PET SWN housing Align the side screw holes in the upper and lower switch Steps 7 5 7 6 late plate housings Attach the lower switch housing to the upper switch 7 2 Feed the upper plug connector through the center opening of the housing housing Lower Switch 7 8 To install each shade first loosen the three thumbscrews Housing Steps 7 1 7 3 7 3 Align the keyhole slots in the housing with the housing assembl Housing j i b 5 4 7 9 Raise the shade to the light fixture Tighten the thumbscrews N T
4. Assembly pA A securely eee screw AU 7 4 Turn the housing counterclockwise until the housing assembly Detail Housing 7 10 Install four B10 candelabra light bulbs 60 Watt maximum each screws are firmly situated in the narrow end of the keyhole slots Install the remaining 16 32 x 3 8 screw into the housing Tighten Note Glass shade style may vary all three screws firmly Housing Assembly Screw 10 i CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing and light fixture falling lt Shade Bulb Steps 7 7 7 9 Hunter Fan Company 42737 01 11 14 06 42737 01 11 14 06 Hunter Fan Company 8 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in seguence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward
5. clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the Same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch Hunter Fan Company In warm weather use downward air flow pattern In cold weather use upward air flow pattern 42737 01 11 14 06 Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation
6. d use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls Low Profile Mounting fits close to the ceiling recommended for ceilings less than 8 feet high Angle Mounting recommended for a vaulted or angled ceiling Standard Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance 2005 Hunter Fan Company Hunter Fan Company 42737 01 11 14 06 42737 01 11 14 06 Hunter Fan Company l Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades in sets as they were shipped Hunter Fan Company To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver e Phillips head screwdriver e Wrench or pliers Ch
7. e screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Screw HE ae pee pe ia 42737 01 11 14 06 2 Installing the Ceiling Plate Isolator gt A x mM Un x a br For Angled Ceilings Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak Hunter Fan Company Gl 3 Assembling and Hanging the Fan Steps 3 1 3 2 lt Downrod lt Canopy Canopy Trim Ring lt Set Screw Hunter Fan Company Low Profile Washer 8 32 x 3 4 Screw You can assemble your fan for standard mounting steps 3 1 3 2 or for low profile mounting steps 3 3 3 4 Note For low profile mounting the downrod is replaced with the low profile washer 3 1 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy and canopy trim ring Feed the wires from the fan through the downrod 3 2 Loosen the allen head set screw on the adapter using the large allen wrench Screw the pipe and ball assembly into the fan assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this
8. e canopy 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal gt A Partially install the three canopy screws into the canopy one at a time Once all three screws are in tighten them Canopy Trim o Ring a z VA o 6 3 Remove the blade mounting screws and rubber shipping bumpers 5 5 Using both hands push the canopy trim ring up to the top of the from the motor Note Some blade mounting screws are installed canopy The canopy trim ring will snap and lock into place in the motor to secure shipping blocks 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Should you need to remove the canopy trim ring follow these steps 1 Locate the tab indicators small bumps on top of tabs WN Use with grommet Screws 2 Press firmly on opposite sides of the ring towards the canopy The tabs will flex out releasing the trim ring from the canopy Steps 5 4 5 5 Use without grommet Blade Mounting Screw Hunter Fan Company 42737 01 11 14 06 42737 01 11 14 06 Hunter Fan Company 7 Completing Your Installation With or Without a Light Fixture Your Hunter fan comes with an integrated light fixture assembly
9. ecking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Check for any shipping damage to the motor or fan blades If one of the fan blades was damaged in shipment return all the blades for replacement If any parts are missing or damaged contact your Hunter dealer or call Hunter Parts Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 42737 01 11 14 06 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter 2 2 Your fan comes with four neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate 2 3 Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate 2 4 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling 2 5 Place a flat washer on each of the two 3 screws and pass th
10. ing according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a gualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install an
11. is normal Securely retighten the set screw with a wrench or pliers Skip to Step 3 5 ii CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod 3 3 Place the low profile washer lip up into the canopy Be sure the green ground wire is pointing up toward the ceiling 3 4 Align the holes in the washer with the holes in the adapter Assemble securely with three 8 32 x 3 4 screws 3 5 Raise the fan and place the hook on the ceiling plate through the U shaped hole in the rim it WARNING Fan may fall if not assembled as directed in these installation instructions U shaped Hole 42737 01 11 14 06 All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Make sure the power to the outlet box and associated wall switch location is still OFF 4 2 To connect the wires hold the bare metal leads together and place a wire nut over them then twist the wire nut clockwise until tight 4 3 Connect the bare or green ground wired grounded from the ceiling to the green ground wire grounded from the ceiling plate and the green ground wire from the fan 4 4 Connec
12. t the white wire ungrounded from the ceiling to the white wired ungrounded from the fan 4 5 Connect the remaining wires as follows Single Switch Wiring e The black wire from the ceiling to the black and the black white wire from the fan Dual Switch Wiring e The black wire from the ceiling to the black wire from the fan e The black white wire from the fan to the wire for the wall switch ia CAUTION Be sure no bare wire or wire strands are visible after making connections 4 6 Turn the splices upward and push them carefully back through the ceiling plate into the outlet box 4 7 Spread the wires apart with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box 42737 01 11 14 06 4 Wiring the Fan Wire Nut Hunter Fan Company 5 Installing the Canopy and Canopy Trim Ring 6 Assembling the Blades Step 5 2 Ceiling Plate 5 1 Holding the canopy raise the fan off the hook Hunter fans use several styles of fan blade irons brackets that hold the 5 2 Align the slots in the canopy with the tabs on the ceiling plate blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail 5 3 Raise the canopy over the ceiling plate Rotate the canopy insert them by hand into the holes on the blades clockwise until the tabs on the ceiling plate totally engage with the slots in th
Download Pdf Manuals
Related Search