Hunter Fan 42405-01 Fan User Manual
Contents
1. 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal E3 6 3 Some blade mounting screws are installed in the motor to secure shipping blocks Remove the blade mounting screws and rubber bumpers from the motor Save the screws and discard the bumpers 6 4 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Steps 6 1 6 2 Use with grommet Crews Use without grommet Blade Mounting Screw 42405 01 01 20 06 Hunter Fan Company 7 Installing the Switch Housing 7 1 7 2 7 3 7 4 Steps 7 1 7 4 Housing Assembly Upper Screw Switch 7 5 Housing Steps 7 5 7 6 Lower Switch Housing KORRINE Assembly Screw Hunter Fan Company To attach the upper switch housing partially install two housing assembly screws into the switch housing mounting plate Feed the upper plug connector through the center opening of the housing Align the keyhole slots in the housing with the housing assembly SCrews Turn the housing counterclockwise until the housing assembly scr2. Considering Optional Accessories than 8 feet high Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum N7 performance of your Hunter fan use only Hunter speed controls n 12 O OYUN Standard Mounting hangs from For ceilings higher than 8 feet you the ceiling by a downrod included can purchase Hunter extension recommended for ceilings 8 feet or higher i downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance 34 Max Angle Mounting recommended for a vaulted or angled ceiling 42405 01 01 20 06 Hunter Fan Company l Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades and blade irons if applicable in sets as they were shipped Hunter Fan Company To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit e Standard screwdriver magnetic tip r
3. 6 Turn power on replace fuse or reset breaker Loosen canopy check all connections according to the Wiring the Fan section Check the plug connection in the switch housing Push motor reversing switch firmly up or down to ensure that the switch is engaged Pull the pull chain to ensure it is on Remove the shipping bumpers Problem Noisy operation i 2 Tighten the blade bracket screws until snug Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 12 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the Hunter Fan Company hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 42405 01 01 20 06
4. installation and Operation manual for Hunter For Your Records and Warranty Assistance ides Ceiling Fans Catalog Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual 42405 01 01 20 06 Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan We are proud of our work We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Cautions and Warnings e Read this entire manual carefully before beginning installation Save these instructions e Use only Hunter replacement parts e To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions 9 and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely f
5. happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has two settings On and Off Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In cold weather having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the Same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Slide the reversing switch on the fan to the opposite position Restart fan Reversing Switch 42405 01 01 20 06 In warm weather use downward air flow pattern In cold weather use upward air flow pattern Hunter Fan Company Il 9 Troubleshooting Problem Nothing happens fan does not move 1 2 5
6. asten a prominent 1 Getting Ready warning device such as a tag to the service panel Table of Contents All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician 2 Installing the Ceiling Plate 3 Assembling and Hanging the Fan 4 e Wiring the Fan To reduce the risk of personal injury do not bend the blade 5 Installing the Canopy attachment system when installing balancing or cleaning the fan 6 Assembling the Blades Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a Solid state speed control with this fan Use only Hunter speed controls 7 Installing the Switch Housing 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting 2006 Hunter Fan Company Hunter Fan Company 42405 01 01 20 06 Installer s Choice and Optional Accessories Understanding Mounting and Installers Choice Hunter s patented 3 position mounting system provides you maximum j installation flexibility and ease You can install your Hunter fan in one 10 of three ways depending on ceiling height and your preference Low Profile Standard or Angle mounting The steps in this manual include instructions for all three Installer s Choice mounting methods Low Profile Mounting fits close to the ceiling recommended for ceilings less
7. ate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate 2 3 Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate 2 4 Place a flat washer on each of the two 3 wood screws 2 5 Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling 2 6 Pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Wood Screw For Angled Ceilings Be sure to orient Erna the ceiling plate so that the two tabs are pointing towards the ceiling peak 42405 01 01 20 06 Hunter Fan Company 3 Assembling and Hanging the Fan Steps 3 2 3 3 lt m Downrod lt lt Canopy Low Profile Washer Low Profile Screw Hunter Fan Company A WARNING Fan may fall if not assembled as directed in these installation instructions 3 1 Unbundle the wires from the fan For Standard or Angled Mounting 3 2 To assemble fan to hang down from a flat or angled ceiling insert the downrod through the canopy Feed the wires from the fan through th
8. e downrod 3 3 Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with a wrench or pliers Skip to Step 3 7 A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod For Low Profile Mounting Note For low profile mounting the downrod is replaced with the low profile washer 3 4 Remove the set screw from the adapter 3 5 Place the low profile washer into the canopy Be sure the green ground wire is pointing up toward the ceiling 3 6 Align the holes in the washer with the holes in the adapter Assemble securely with three low profile screws 3 7 Raise the fan and align the slots in the canopy with the tabs on the ceiling plate Ceiling Plate Tabs Canopy Slots 42405 01 01 20 06 All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Make sure the power to the outlet box and associated wall switch location is still OFF To connect the wires ho
9. ecommended e Phillips head screwdriver magnetic tip recommended e Wrench or pliers e Ladder height dependent upon installation site Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Refer to the included Parts Guide Check for any shipping damage to the motor or fan blades If any parts are missing or damaged contact your Hunter dealer or call Hunter Technical Support Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 42405 01 01 20 06 2 Installing the Ceiling Plate A CAUTION To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box Ceiling and associated wall switch location If you cannot lock the circuit breakers Plate Pw in the off position securely fasten a prominent warning device such as a tag to the service panel Pa 2 1 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter al 2 2 Your fan comes with two neoprene noise isolators Isolators Position the isolators between the ceiling pl
10. ews are firmly situated in the narrow end of the keyhole slots Install the remaining housing assembly screw into the housing Tighten all three screws firmly A CAUTION Make sure the upper switch housing is securely attached to the switch housing mounting plate Failure to properly attach and tighten all three assembly screws could result in the switch housing fixture falling To attach the lower switch housing connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product Place the lower switch housing assembly over the upper switch housing Align the side screw holes in the upper and lower switch housings Attach the lower switch housing to the upper switch housing with three housing assembly screws 42405 01 01 20 06 8 1 8 2 8 3 8 5 8 6 8 Operating and Cleaning Your Ceiling Fan Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this
11. ld the bare metal leads together and place a wire nut over them then twist the wire nut clockwise until tight A CAUTION Be sure no bare wire or wire strands are visible after making connections Connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black wire from the fan 4 2 Push all wires and wire nuts into the outlet box 42405 01 01 20 06 a Q Fe 4 Wiring the Fan Single Switch Wiring ae _ il Hunter Fan Company 5 Installing the Canopy Step 5 1 5 1 Rotate the hanger ball so the tab in the canopy is secure in the groove in the hanger ball A WARNING Failure to complete this step could cause fan to fall 5 2 Lift the fan and align the canopy screw holes with the mounting holes on the ceiling plate 5 3 Partially install a canopy screw into the side opposite the ceiling plate tabs 5 4 Partially install another canopy screw into the hole between the two ceiling plate tabs Securely tighten both screws Step 5 3 Step 5 4 Hunter Fan Company 42405 01 01 20 06 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan
Download Pdf Manuals
Related Search