Hunter Fan 41931-01 Fan User Manual
Contents
1. 2 Decide how you want to set up the fan and light controls You can control the fan and or lights together or separately using one or two wall switches Follow Step 4 3 OR Step 4 4 depending on what you decide Note If you are not installing a light kit follow step 4 4 4 3 If you want to you can control the fan and light separately using two wall switches connect the wires as follows The bare or green ground wire from the ceiling to the green Step 4 4 ground wire from the hanger bracket and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan The black wire from the ceiling to the black wire from the fan The black white wire from the fan to the wire for the wall switch 4 4 Alternatively you can control both fan and light with one switch To do so connect the wires as follows The bare or green ground wire from the ceiling to the green ground wire from the hanger bracket and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan The black wire from the ceiling to the black and the black white wire from the fan 4 5 To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight Wire Nut A CAUTION Be sure no bare wire or wire strands are visible after making connections 4 6 Push all wires and wire nuts back into the h2. the off position securely fasten a prominent 2 Installing the Hanger Bracket warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician To reduce the risk of personal injury do not bend the blade 6 Assembling the Blades attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not use a solid state speed control with this fan Use only Hunter speed controls wo e 1 Getting Ready 3 e Assembling and Hanging the Fan 4 Wiring the Fan 5 Installing the Canopy 7 Installing the Switch Housing 8 Operating and Cleaning Your Ceiling Fan 9 Troubleshooting 2004 Hunter Fan Company Hunter Fan Company 42008 01 12 07 05 Mounting and Optional Accessories Understanding Mounting Hunter s patented mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of two ways depending on your preference Standard or Angle mounting The steps in this manual include instructions for both mounting methods Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow
3. Mm WU He o 3 CO installation and Operation manual for Hunter Ceiling Fans 42008 01 12 07 05 f Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan For Your Records and Warranty Assistance Model Name PE en We are proud of our work We appreciate the opportunity to supply Catalog Model No _ _ _ you with the best ceiling fan available anywhere in the world Serial No Before installing your fan for your records and warranty assistance record information from the carton and Hunter nameplate label located on the top of the fan motor housing Date Purchased Where Purchased Cautions and Warnings For reference also attach your receipt or a e Read this entire manual carefully before beginning installation Save copy of your receipt to the manual ece i lt Gn e Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan Table of Contents disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in
4. anger bracket 42008 01 12 07 05 Hunter Fan Company 5 w Installing the Canopy Steps 5 1 5 2 Hanger Bracket Note To adjust the canopy screws in steps 5 1 5 3 you will need to reach under and pull up the rim of the ceiling gasket 5 1 Raise the canopy over the hanger bracket Align partially installed screws with key slots in canopy gt 5 2 Twist canopy clockwise to secure 5 3 Install third canopy screw in round hole on canopy Securely tighten all three screws Step 5 3 Hunter Fan Company 42008 01 12 07 05 6 Assembling the Blades Hunter fans use several styles of fan blade irons brackets that hold the blade to the fan 6 1 Your fan may include blade grommets If your fan has grommets Step 6 1 Detail insert them by hand into the holes on the blades 6 2 Attach each blade to a blade iron using three blade assembly screws If you used grommets the blades may appear slightly loose after screws are tightened This is normal 6 3 For each blade insert one blade mounting screw through the blade iron and attach lightly to the fan Insert the second blade mounting screw then securely tighten both mounting screws Blade Assembly Use with grommet Pelee Use without grommet Blade Mounting Screw 42008 01 12 07 05 Hunter Fan Company 7 Installing the Switch Housing Note If you are installing a light fixcure do NOT install the switch h
5. ierce two holes in the ceiling gasket that match the pilot holes you drilled in step 2 1 Use the marks on the hanger bracket from step 2 3 as your guide Thread the lead wires from the outlet box down through the hole in the middle of the ceiling gasket and hanger bracket Note The ceiling gasket should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the ceiling gasket and hanger bracket into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten 42008 01 12 07 05 Flat Washer 3 Screw Canopy 2 Installing the Hanger Bracket _ Ceiling Gasket Hanger Bracket For Angled Ceilings Be sure to orient the hanger bracket with the large opening towards the ceiling peak Hunter Fan Company 3 Assembling and Hanging the Fan Standard abel Mounting Washer PR Canopy Step 3 1 Steps 3 2 3 5 lt Downrod lt lt Canopy with Washer Hanger Pipe Sleeve IL x _ Adapter Set Screw oe Cover MW Hunter Fan Company You can assemble your fan for standard or angle mounting as shown in steps 3 1 3 7 3 1 Remove the label from the standard mounting washer inside the canopy Leave the washer in place 3 2 To assemble the fan to hang down from a flat
6. n blades was damaged in shipment return all the blades for replacement If any parts are missing or damaged contact your Hunter dealer or call Hunter Parts Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 42008 01 12 07 05 2 3 2 4 25 2 6 2 7 2 8 MYN Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other If you are installing the fan on an angled ceiling be sure to orient the hanger bracket with the large opening towards the ceiling peak Use an indelible marker to mark the exact location of the pilot holes relative to the slots on the hanger bracket Remove the hanger bracket Partially install two canopy screws about 2 full turns in the hanger bracket Place the ceiling gasket over the hanger bracket so that the slots and the raised surfaces on the ceiling gasket align with the slots and holes on the hanger bracket Use a 3 screw to p
7. n cold weather use upward air flow pattern Hunter Fan Company Il 9 Troubleshooting 12 Hunter Fan Company Problem Nothing happens fan does not move 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Pull the pull chain to ensure it is on 5 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Check to see if the blade is cracked If so replace all the blades Problem Excessive wobbling 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our WEB site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 42008 01 12 07 05
8. or angled ceiling insert the downrod through the canopy 3 3 Feed the wires from the fan through the downrod 3 4 Screw the downrod into the fan assembly 3 5 Using the provided allen wrench loosen the allen head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads on the pipe will still be visible this is normal Securely retighten the set screw with the allen wrench A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A WARNING Do not carry or lift fan by canopy 3 6 Raise the fan and place the ball into the hanger bracket 3 7 Align the notch on the ball with the indent in the hanger bracket Rotate the fan until you hear the notch pop into place WARNING Fan may fall if not assembled as directed in these installation instructions Steps 3 6 3 7 42008 01 12 07 05 4 Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a gualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 4 1 Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location 4
9. ousing without first referring to the instructions included with the light fixture 7 1 Align the holes on the blade iron cover and gasket and stick two screws through two of the holes 7 2 Thread the plug connector from the mounting plate through the gasket and cover Partially install the gasket and cover to the mounting plate with the two screws Blade Iron Cover 7 3 Place the upper switch housing over the two screws and turn Steps 7 1 7 2 counterclockwise so that the screws fit securely in the slots 7 4 Partially install the third screw and then tighten all three screws securely 7 5 Connect the upper plug connector from the motor to the lower plug connector in the switch housing assembly Note Both plug connectors are polarized and will only fit together one way Make sure the connectors are properly aligned before connecting them Incorrect connection could cause improper operation and damage to the product 7 6 To attach the lower switch housing thread the thumb screws through the side holes of the upper switch housing and tighten them securely Note You can customize your Hunter fan with a number of accessory light kits 4 ih x vA ll il l N _ a Y NY Thumbscrew Hunter Fan Company 42008 01 12 07 05 8 Operating and Cleaning Your Ceiling Fan 8 1 Turn on electrical power to the fan 8 2 The fan pull chain con
10. the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls For ceilings higher than 8 feet you can purchase Hunter extension downrods All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance 42008 01 12 07 05 12 Standard Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher Ly lt 34 Max o oo yU Angle Mounting recommended for a vaulted or angled ceiling Hunter Fan Company l Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades in sets as they were shipped Hunter Fan Company To install a ceiling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit Standard screwdriver e Phillips head screwdriver e Wrench or pliers Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Check for any shipping damage to the motor or fan blades If one of the fa
11. trols power to the fan The pull chain has four settings in sequence High Medium Low and Off e Pull the chain slowly to change settings e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector 8 3 To change airflow direction turn the fan off and let it come to a complete stop Pull the reversing pullchain one time and then restart the fan Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft 8 4 For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish 8 5 Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish 42008 01 12 07 05 In warm weather use downward air flow pattern I
Download Pdf Manuals
Related Search