Hunter Fan 41897-01 Fan User Manual
Contents
1. Canopy Trim Ring Step 3 4 Pipe and Twig Assembly gt Set Screw Ground Wire and Screw a Www Steps 3 6 3 8 Hunter Fan Company 3 1 3 2 3 3 3 4 Loosen the sguare head set screw in the adapter Loosen the set screws and the assembly screws on the twig clamp Thread the wires from the fan through the canopy trim ring and spindle Then thread the wires through the pipe and twig assembly Install the pipe into the adapter Note When the downrod is fully installed 2 3 threads will still be visible this is normal Securely retighten the set screw with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A CAUTION Do not carry or lift fan by the canopy Lower the pipe and twig assembly onto the spindle Tighten the set screws and the assembly screws on the twig clamp using the provided allen wrench ATTENTION Do not overtighten the set screws doing so will damage the wrench Thread the wires from the fan through the canopy Remove the pipe ball screw from the standard downrod then slide the ball off the pipe Remove the pin from the pipe then slide the wedge off the pipe Remove the screw and ground wire from the pipe Reassemble the ball wedge pin ground wire and pipe ball screw in that order on2. e Release slowly to prevent the chain from recoiling into the blades e The chain uses a breakaway connector that separates if the chain is jerked If this happens simply reinsert the chain into the connector The light pull chain controls power to the light The pull chain has two settings On and Off Ceiling fans work best by blowing air downward counterclockwise blade rotation in warm weather to cool the room with a direct breeze In winter having the fan draw air upward clockwise blade rotation will distribute the warmer air trapped at the ceiling around the room without causing a draft For cleaning finishes use a soft brush or lint free cloth to prevent scratching A vacuum cleaner brush nozzle can remove heavier dust Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth You may use an artistic agent but never abrasive cleaning agents as they will damage the finish Clean wood finish blades with a furniture polishing cloth Occasionally apply a light coat of furniture polish for added protection and beauty Clean painted and high gloss blades in the same manner as the fan finish To Change Airflow Direction Turn the fan off and let it come to a complete stop Press the reversing switch on the fan You will need to remove the light kit glass to do so Restart fan 41897 01 11 22 05 10 Troubleshooting Problem Nothing happens fan does not move
3. 1 Turn power on replace fuse or reset breaker 2 Loosen canopy check all connections according to the wiring the fan section 3 Check the plug connection in the switch housing 4 Push motor reversing switch firmly left or right to ensure that the switch is engaged You will need to remove the light kit glass to do so 5 Pull the pull chain to ensure it is on 6 Remove the shipping bumpers Problem Noisy operation 1 Tighten the blade bracket screws until snug 2 Tighten the blade screws until snug 3 Check to see if the blade is cracked If so replace all the blades 4 Be sure that the glass is secure Problem Excessive wobbling B 1 If your fan wobbles when operating use the enclosed balancing kit and instructions to balance the fan 2 Tighten all blade and or blade iron screws 3 Turn power off support fan very carefully and check that the hanger ball is properly seated If you need parts or service assistance please call 888 830 1326 or visit us at our Web site at http www hunterfan com Hunter Fan Company 2500 Frisco Avenue Memphis Tennessee 38114 41897 01 11 22 05 Hunter Fan Company
4. available use a magnetic tip screwdriver 5 1 Insert the grommets into the holes in the blades 5 2 Attach each blade to the blade iron and medallion using the three blade assembly screws Insert the assembly screws into the blade iron through the blade and into the medallion with the blade captured between the blade iron and medallion The blades may appear slightly loose after the screws are tightened This is normal 5 3 Remove the blade iron mounting screws from the motor Discard the shipping blocks and save the screws 5 4 Partially install one blade iron mounting screw through a blade iron and into the motor Insert a second blade iron mounting screw then securely tighten both screws 5 5 Raise the fan and place the hook on the ceiling plate through the U shaped hole in the rim of the canopy A WARNING Fan may fall if not assembled as directed in these installation instructions Y Screw x Blade Iron Steps 5 1 5 4 Step 5 5 VN Screw Blade Assembly a x Y F g Grommet a F i Hunter Fan Company 41897 01 11 22 05 All wiring must be in accordance with national and local electrical codes and ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician Wall switches are not included Select an acceptable general use switch in accordance with national and local electrical codes 6 1 6 2 6 4 6 5 6 6 Disconnect the power by tur
5. position securely fasten a prominent FFF ener warning device such as a tag to the service panel All wiring must be in accordance with national and local electrical 5 Assembling the Blades and codes and ANSI NFPA 70 If you are unfamiliar with wiring use a Hanging the Fan qualified electrician To reduce the risk of personal injury do not bend the blade attachment system when installing balancing or cleaning the fan Never insert foreign objects between rotating fan blades To reduce the risk of fire electrical shock or motor damage do not 8 Assembling the Light Fixture use a solid state speed control with this fan Use only Hunter speed 9 Operating and Cleaning controls Your Ceiling Fan 1 Getting Ready 2 Assembling the Fan for Ceilings 8 10 Feet High 4 Installing the Ceiling Plate 6 e Wiring the Fan 7 Installing the Canopy and Canopy Trim Ring 10 Troubleshooting 2005 Hunter Fan Company Hunter Fan Company 41897 01 11 22 05 Understanding Mounting Hunter s patented mounting system provides you maximum installation flexibility and ease You can install your Hunter fan in one of two ways depending on your preference Standard or Angle mounting Your fan may only be installed on ceilings 8 feet or higher A standard downrod is provided for installing your fan on a ceiling 8 10 feet high Note The decorative twig attachment will not fit on the standard downrod For ceili
6. 11 22 05 6 Wiring the Fan Wire Nut Hunter Fan Company 7 Installing the Canopy and Canopy Trim Ring Step 7 2 gt Ceiling Plate gt Canopy Trim S Ring Step 7 3 Steps 7 4 7 5 Hunter Fan Company 7 1 Holding the canopy raise the fan off the hook 7 2 Align the slots in the canopy with the tabs on the ceiling plate 7 3 Raise the canopy over the ceiling plate Rotate the canopy clockwise until the tabs on the ceiling plate totally engage with the slots in the canopy 7 4 Partially install the three canopy screws into the canopy one at a time Once all three screws are in tighten them 7 5 Using both hands push the canopy trim ring up to the top of the canopy The canopy trim ring will snap and lock into place Should you need to remove the canopy trim ring follow these steps 1 Locate the tab indicators small bumps on top of tabs 2 Press firmly on opposite sides of the ring towards the canopy The tabs will flex out releasing the trim ring from the canopy 41897 01 11 22 05 8 1 To attach the light fixture partially install two 6 32 x 3 8 assembly screws 8 2 Connect the 9 pin plug from the fan housing to the connector from the light kit 8 3 Place the keyhole slots in the light fixture over the partially installed screws 8 4 Turn the light fixture counterclockwise until the assembly scr
7. Mm WU He o 3 CO installation and Operation manual for Hunter Ceiling Fans 41897 01 11 22 05 mi Welcome Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years This installation and operation manual gives you complete instructions for installing and operating your fan For Your Records and Warranty Assistance Model Name We are proud of our work We appreciate the opportunity to supply UA you with the best ceiling fan available anywhere in the world Serial No Before installing your fan for your records and warranty assistance DRODD e record information from the carton and Hunter nameplate label Where Purchased located on the top of the fan motor housing For reference also attach your receipt or a Cautions and War nings copy of your receipt to the manual e Read this entire manual carefully before beginning installation Save these instructions e Use only Hunter replacement parts To reduce the risk of personal injury attach the fan directly to the Table of Contents support structure of the building according to these instructions and use only the hardware supplied To avoid possible electrical shock before installing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock 3 Assembling the Fan for Ceilings the circuit breakers in the off
8. ews are firmly situated in the narrow end of the keyhole slots 8 5 Install the remaining 6 32 x 3 8 screw into the light fixture Tighten all three screws firmly A CAUTION Make sure the light fixture is securely attached Failure to properly attach and tighten all three assembly screws could result in the light fixture falling 8 6 Thread the pull chains through the metal disk at the bottom of the light kit 8 7 Install three candelabra bulbs 40 Watts maximum each 8 8 Thread pull chains through the hole in the center of the glass bowl and the center of the lower twig 8 9 Thread the pull chains through the holes in the cover plate 8 10 Install the finial to secure the cover plate twigs and bowl q p Cover Plate lt Finial Steps 8 8 8 10 41897 01 11 22 05 8 Assembling the Light Fixture Light Kit Steps 8 1 8 3 Assembly Screw Metal Disk Assembly Screw Steps 8 4 8 6 gt Step 8 7 Hunter Fan Company 9 Operating and Cleaning Your Ceiling Fan In warm weather use downward air flow pattern 12 In cold weather use upward air flow pattern Hunter Fan Company 9 1 9 2 9 3 9 4 Turn on electrical power to the fan The fan pull chain controls power to the fan The pull chain has four settings in seguence High Medium Low and Off e Pull the chain slowly to change settings
9. ling fan be sure you can do the following e Locate the ceiling joist or other suitable support in ceiling e Drill holes for and install wood screws e Identify and connect electrical wires e Lift 40 pounds If you need help installing the fan your Hunter fan dealer can direct you to a licensed installer or electrician Gathering the Tools You will need the following tools for installing the fan e Electric drill with 9 64 bit Standard screwdriver e Phillips head screwdriver e Wrench or pliers Checking Your Fan Parts Carefully unpack your fan to avoid damage to the fan parts Check for any shipping damage to the motor or fan blades If one of the fan blades was damaged in shipment return all the blades for replacement If any parts are missing or damaged contact your Hunter dealer or call Hunter Parts Department at 888 830 1326 Preparing the Fan Site Before you begin installing the fan follow all the instructions in the pullout sheet called Preparing the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety reliable operation maximum efficiency and energy savings 41897 01 11 22 05 2 Assembling the Fan for Ceilings 8 10 Feet High To install the fan on ceilings 8 10 feet high follow the steps in this section Skip to the next section if you are installing the fan on a ceiling 10 feet or higher 2 2 2 2 3 2 4 2 5 2 6 Remo
10. ngs 10 feet or higher an extension downrod and decorative twig attachment are provided The decorative twig cannot be added to the fan when installing on ceilings lower than 10 feet If you want to install on a ceiling 8 10 feet high follow section 2 e Assembling the Fan for Ceilings 8 10 Feet High on page 5 If you want to install the fan on a ceiling 10 feet or higher follow section 3 e Assembling the Fan for Ceilings 10 Feet or Higher on page 6 Considering Optional Accessories Consider using Hunter s optional accessories including a wall mounted or remote speed control To install and use the accessories follow the instructions included with each product For quiet and optimum performance of your Hunter fan use only Hunter speed controls 41897 01 11 22 05 Mounting and Optional Accessories 12 Standard Mounting hangs from the ceiling by a downrod included recommended for ceilings 8 feet or higher Angle Mounting recommended for a vaulted or angled ceiling Your fan includes an extension downrod which should be used only when installing the fan on a ceiling 10 feet or higher All Hunter fans use sturdy 3 4 diameter pipe to assure stability and wobble free performance Hunter Fan Company l Getting Ready Installing Multiple Fans If you are installing more than one fan keep the fan blades in sets as they were shipped Hunter Fan Company To install a cei
11. ning off the circuit breakers to the outlet box and associated wall switch location Decide how you want to set up the fan and light controls You can control the fan and or lights together or separately using one or two wall switches Follow Step 6 3 OR Step 6 4 depending on what you decide If you want to you can control the fan and light separately using two wall switches connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan The black wire from the ceiling to the black wire from the fan The black white wire from the fan to the wire for the wall switch Alternatively you can control both fan and light with one switch To do so connect the wires as follows e The bare or green ground wire from the ceiling to the green ground wire from the ceiling plate and the green ground wire from the fan e The white wire from the ceiling to the white wire from the fan e The black wire from the ceiling to the black and the black white wire from the fan To connect the wires hold the bare metal leads together and place a wire nut over them then twist clockwise until tight A CAUTION Be sure no bare wire or wire strands are visible after making connections Push all wires and wire nuts back through the ceiling plate hole into the outlet box 41897 01
12. to the long downrod 41897 01 11 22 05 4 2 4 4 4 5 Drill two pilot holes into the wood support structure through the outermost holes in the outlet box The pilot holes should be 9 64 in diameter Your fan comes with four neoprene noise isolators Isolators Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate Thread the lead wires from the outlet box down through the hole in the middle of the ceiling plate Align the slotted holes in the ceiling plate with the pilot holes you drilled in the wood support structure For proper alignment use slotted holes directly across from each other Note The isolators should be flush against the ceiling Place a flat washer on each of the two 3 screws and pass the screws through the slotted holes in the ceiling plate into the pilot holes you drilled Tighten the screws into the 9 64 pilot holes do not use lubricants on the screws Do not over tighten Flat Washer 3 Screw MYNNY 41897 01 11 22 05 4 Installing the Ceiling Plate Isolator gt S Ceiling Plate ee T A y Ml For Angled Ceilings Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak Hunter Fan Company 5 Assembling the Blades and Hanging the Fan Note If
13. ve the two assembly screws in the upper clamp Insert the downrod through the canopy canopy trim ring and spindle Feed the wires from the fan through the downrod Loosen the square head set screw on the adapter to install the pipe and ball assembly Note When the pipe and ball assembly is fully installed 2 3 threads will still be visible this is normal Securely retighten the set screw with a wrench or pliers A CAUTION The adapter has a special coating on the threads Do not remove this coating the coating prevents the downrod from unscrewing Once assembled do not remove the downrod A CAUTION Do not carry or lift fan by the canopy Lower the spindle onto the lower clamp Reassemble the upper clamp around the pipe using the two assembly screws removed in Step 2 1 Lower the clamp onto the spindle Tighten the set screws using the provided allen wrench ATTENTION Do not overtighten the set screws doing so will damage the wrench Go to 4 Installing the Ceiling Plate on page 7 to continue the installation 41897 01 11 22 05 Upper Clamp Set Screw Assembly Screw Step 2 2 Canopy gt Canopy Spindle Trim Ring Mil T ow Il Set Screw gt mm Steps 2 4 2 5 Upper Clamp Hunter Fan Company 3 Assembling the Fan for Ceilings 10 Feet or Higher Step 3 2 Canopy Pipe and Twig Assembly m p Twig Clamp Ee Spindle
Download Pdf Manuals
Related Search