Home

Humminbird 967C Fish Finder User Manual

1. 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 3D Bottom Zoom setting Off 1 5x 2x 2 5x 3x Default Off gt 3D Lower Range Auto 3D Lower Range Auto 240 3D Lower Range sets the deepest depth range that will be displayed and is only available on the 3D Sonar X Press Menu when you are in the 3D Sonar 3D 2D Sonar Combo or the 6 Beam Sonar View Automatic is the default setting When in automatic mode the lower range will be adjusted by the unit to follow the bottom Selecting a specific setting locks the depth range into Manual mode For example if you are fishing in 60 feet of water but are only interested in the first 30 feet surface to a depth of 30 feet you should set the Lower Depth Range limit to 30 The display will show the 0 to 30 foot range allowing you to see a more detailed view than you would see if the display went all the way to the bottom To adjust the 3D Lower Range 1 Highlight 3D Lower Range on the 3D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to increase or decrease the Lower Range setting AUTO 10 to 240 feet 3 to 5 meters International Models Only Default AUTO 3D History 3D History 4 Least Most 3D History determines the speed at which the sonar information moves across the display and consequently the amount of history shown and is only available on the 3D Sonar X Press Menu when you are in the 3D Sonar or the 3D 2D Sonar C
2. Installatio lation and Operations Manual 967c GP S fishing System 3D Sonar D 967c Thank You Thank you for choosing Humminbird America s 1 name in fishfinders Humminbird has built its reputation by designing and manufacturing top quality thoroughly reliable marine equipment Your Humminbird is designed for trouble free use in even the harshest marine environment In the unlikely event that your Humminbird does require repairs we offer an exclusive Service Policy free of charge during the first year after purchase and available at a reasonable rate after the one year period For complete details see the Warranty section in this manual We encourage you to read this installation and operations manual carefully in order to get full benefit from all the features and applications of your Humminbird product Contact our Customer Resource Center at either 1 800 633 1468 or visit our website at www humminbird com WARNING This device should not be used as a navigational aid to prevent collision grounding boat damage or personal injury When the boat is moving water depth may change too quickly to allow time for you to react Always operate the boat at very slow speeds if you suspect shallow water or submerged objects WARNING Disassembly and repair of this electronic unit should only be performed by authorized service personnel Any modification of the serial number or attempt to repair the original equipment
3. area and to identify on which side of the boat they are located See DualBeam PLUS Quick Disconnect Mount The Quick Disconnect Mounting system is an exclusive Humminbird feature that permits the unit to be easily removed from the mounting base by pressing a release button and re installed by simply snapping it back into place All cable connections are made when installing so that no separate wiring connections are required Additionally the mount offers 90 tilt and 360 swivel capability to adjust the viewing angle of the unit as you move about the boat Real Time Sonar Real Time Sonar is a Humminbird technology that delivers ultra fast sonar transmitter receiver operation and results in a more detailed instantaneous view of what is under the boat The Real Time Sonar window is a vertical band at the right side of the display that shows the instantaneous sonar return from the transducer at a particular instant The RTS Window menu option permits the user to adjust the window to show the full sonar signal return or just a narrower band that indicates intensity using grayscale Real Time Sonar relies on very fast Sonar Update Rate Ping Speed See Sonar Update Rate Receiver See ransmitter Second Return The Second Return is a term that describes the appearance of a second sonar return below the primary sonar return bottom contour at exactly twice the true depth The second return is caused by the same sonar energy boun
4. e Include a copy of your receipt to show proof and date of purchase e Return product freight prepaid to Humminbird using an insured carrier with delivery confirmation For OUT OF WARRANTY service complete the following steps Obtain a Repair Authorization Number from the Humminbird Customer Resource Center Include payment in the form of credit card number and expiration date money order or personal check Please do not send cash Tag product with your name street address phone number and your assigned Repair Authorization Number Include a brief written description of the problem Return product freight prepaid to Humminbird using an insured carrier with delivery confirmation 119 900 Series Accessories Accessories customize the 900 Series to your needs and enable you to stay on the edge of new technology When an accessory is connected to the 900 Series additional menus and readouts are added automatically to the Main Menu System Accessories available today that are supported by your 900 Series include WeatherSense Fishing Condition Monitor purchase and plug in the WeatherSense accessory to your 900 Series to obtain barometric pressure readouts and trend data in real time GPS Connection Cable purchase the GPS Connection Cable in order to connect a handheld or other NMEA GPS compatible device that you may already own to your 900 Series NMEA 0183 Is a National Marine Elect
5. Make sure you are in Advanced User Mode then highlight Clear Map Offset on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control key to clear the Map Offset 98 Alarms X X had 5 Ce oF Depth Alarm Of Of Alarms Menu Tab From any view press the MENU key twice to access the Main Menu System The Alarms tab will be the default selection f Fish ID Alarm O Low Battery Alarm f Aux Temp Alarm t NOTE When an alarm is triggered you can silence It by pressing any key The alarm will be Silenced and will not be triggered again until a new instance of the alarm condition is detected Off Off 328ft 164f Off Medium 7 Alarms Menu Depth Alarm off Depth Alarm off _ 100 Depth Alarm sounds when the depth becomes equal to or less than the menu setting To change the Depth Alarm setting 1 Highlight Depth Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Depth Alarm setting OFF 1 to 100 feet or 0 5 to 30 meters International models only Default OFF Fish ID Alarm Fish ID Alarm 0 2 Fish ID Alarm sounds when the 900 Series detects fish that correspond to the alarm setting Fish ID Alarm will only sound if Fish ID is on For example if you ve set the Fish ID Alarm to sound for Large fish only the Fish ID alarm will sound when a large sized fish is detected of O ie a ql axa gt Large Mediu
6. NOTE Installation details may vary with unit configuration 2 Mark the mounting location and drill a 3 4 19 mm hole for the cable and cable plug Route the cable 3 Cover the cable hole with the receiver Make sure the receiver is flush on the surface and mark the two mounting holes with a pencil Or punch 4 Move the receiver to the side and drill two pilot holes using a 9 64 3 5 mm bit NOTE Remember to caulk or seal screw holes and drilled holes as needed to protect your boat trom water damage 9 Align the GPS receiver screw holes over the pilot screw holes and attach with the 8 1 1 4 Phillips head screws Hand tighten only NOTE If the mounting surface is thin and made of a lighter material a backing material may be needed below the mounting surface 23 Access Under Mounting Location No Access Under Mounting Location No Access Under Mounting Location Follow these steps to deck mount the GPS receiver in a situation where you must route the cable to the side because there is no space for a cable underneath the mounting location 1 Determine the best location then test route the cable from the mounting location to the control head NOTE AS EC10 10 extension cables are available from Humminbird if your planned routing exceeds 20 6 m Maximum cable length including extensions should not exceed 50 16 m 2 Confirm the cable length is good and route the cable from the receiver to t
7. Press MENU for Startup Options 900 Series 967c Combo Title Screen What s On the 3D Sonar Display The 900 Series can display a variety of useful 3D information about the area under and adjacent to your boat including the following items Triplog 3D Bottom Contour Shows the shape of the bottom derived from depth measurements on 6 beams 3 bottom styles are available the front edges of the bottom contour are outlined to create a visual anchor The width of the bottom covered is approximately equal to the depth Upper Depth Range Lower Depth Range Frame provides a reference for bottom and Fish ID information A Range of frame styles are available from simple to complex eU 2 Depth water depth can be set to alarm when the water becomes too shallow 2D Sonar View traditional 2D sonar for the identification of structure and bottom hardness _ Timer Elapsed time with Speed input or GPS Receiver Boat Direction Arrow A simple solid 3D boat is drawn when the Upper Depth Range is 0 A solid 3D arrow is drawn Distance Distance traveled with Speed input or GPS Receiver when the Upper Depth Range is not 0 Average Speed Average speed reading with Speed input or GPS Receiver Fish ID A fish icon will be shown at the derived position of the fish Six fish icon styles will be used to indicate the primary beam in which the fish was found Left facing fish indicate fish off th
8. Set Simulation Position Advanced oocceccccccsccceceescsecseseseseseseseresesesereeerereeren 97 Set Map SON Mavancod seisonnan 97 Clear Map ONSET Aono arasin 98 Alarms Menu Tab 98 EDA E E E A A san 99 AR DE EU i E N EA E E E N E 99 Eo tes GA N A crete nec P E E E E E 99 Aux Temp Alarm with optional purchase temp probe or Temp Speed only n u 100 Jemp Alarm ooo ececceccscscsscssscsssscsssscscesssesssessscsrssssrssesrssescssssceissceisacsteesaceesaeeeaes 100 UT OURS GP TG cet snes costiraasannsats cattetze E te aruscenatnees tote 101 POV GIL Ss VAIN aE watt E EE E AR 101 LEGIT VOT E oatnrca satan nueateat AE nee ete AE 102 PAI NOMIC EEE E AE A E A 102 Setup Menu Tab 103 Daa OUI E AAE E A EE E E EEE 103 Units Temp international only 103 Units Distance with Speed input only o s 104 Units Speed with Speed input only ccccecsccsescecssssesessesssseseseseeeseseseeeeeees 104 User MOde c cccccccscsccscsescssssessssessssessessseessscessscesssssteesseeesseessessesestsesaeeeseesess 104 Language International only s es 104 Triplog Reset with Speed input only ccccccsccccssescscestessstssestssescssscssseesseeceseaes 105 Fe SEI SAE E E E AE 105 Select Readouts Advanced eecececcccccsecesesesesesesesesesesesesesesesesesesevevevevevsvenerens 105 Depin Onset AQ IE rns ccceses tecctiraetesstasctttrncaueton N E 107 Aux lemp Oifset PAGV ACEO seneuirewnansnianennn 107 Temp Onset AOVANGEO aienea a aE hia 107 Speed Calibrati
9. To clear the current track press the RIGHT Cursor key once more To cancel clearing the current track press the LEFT Cursor key El Save Current Route Save Current Route b Only when navigating Save Current Route allows you to save the current route being displayed This menu choice will only appear when you are currently navigating a route To Save Current Route 1 Highlight Save Current Route on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate saving the current route 3 The Confirm dialog box will appear To save the current route press the RIGHT Cursor key once more To cancel saving the current route press the LEFT Cursor key A Skip Next Waypoint Skip Next Waypoint b Only when navigating Skip Next Waypoint removes the next waypoint from the current route This menu choice will only appear when you are currently navigating a route To Skip Next Waypoint 1 Highlight Skip Next Waypoint on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate skipping the next waypoint 3 The Confirm dialog box will appear To skip the next waypoint press the RIGHT Cursor key once more To cancel skipping the next waypoint press the LEFT Cursor key 74 Cancel Navigation Only when navigating ks Cancel Navigation gt Cancel Navigation discards the current route and exits Navigation Mode This menu choice will only appear when you are currently nav
10. You can perform any of the functions for either of these views but only when the view you want to control is selected as the active side see 3D Sonar X Press Menu Active Side or Navigation X Press Menu Active Side for more information A green arrow points to the side that is active You can also adjust the size of the left side of a split screen see 3D Sonar X Press Menu Split Position or Navigation X Press Menu Split Position for more information NOTE See 3D 2D Combo View and Chart View for more information about each side of this view 48 Chart 3D Combo View Depth ft Wy Course t a pt _ m _ i P i O l i i j i i i f ay In Hg eal ee Ka lt g p BE 4 EE d j le oO Depth Upper Depth Range Q O Course Direction that boat is travelling relative to North Reference Lower Depth Range O enperature 3D Boat Icon Q O Speed Waypoint Q 30 view Cartography O Chart View Map Scale Chart 2D Combo View Chart 2D Combo View shows both the Chart and 2D Sonar views in a combination split screen You can perform any of the functions for either of these views but only when the view you want to control is selected as the active side see 2D Sonar X Press Menu Active Side or Navigation X Press Menu Active Side for more information A green arrow points to the side that is active You can also adjust the size
11. ae Chart Speed 5 Chart Speed E o Chart Speed determines the speed at which the sonar information moves across the display and consequently the amount of detail shown A faster speed shows more information in the Sonar Views and is preferred by most anglers however the sonar information moves across the display quickly A slower speed keeps the information on the display longer but the bottom and fish details become compressed and may be difficult to interpret Regardless of the Chart Speed setting the RTS Window will update at the maximum rate possible for the depth conditions Adjust Chart Speed to your personal preference To adjust the Chart Speed 1 Highlight Chart Speed on the 2D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to increase or decrease the Chart Speed setting 1 10 where 1 Slowest 10 Fastest Default 5 Bottom Lock 2D Zoom View only Bottom Lock q Off p Bottom Lock changes the mode of the Zoomed view in the 2D Zoom View Bottom Lock continuously graphs the bottom at a constant point on the display regardless of changes in depth This flattens out the bottom contour but is effective at showing fish on or near the bottom 66 To turn on Bottom Lock 1 In the 2D Zoom View highlight Bottom Lock on the 2D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Bottom Lock setting to on Off On Default Off Bottom Range 15
12. 0 Local Time Zone 4 EST UTC 5 p Local Time Zone selects your time zone in reference to the time reported by the GPS receiver when Time Date is selected as a Digital Readout on the Sonar View see Select Readouts This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode Local Time Zone Advanced To change the Local Time Zone 1 Make sure you are in Advanced User Mode then highlight Local Time Zone on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Local Time Zone Default EST UTC 5 Eastern Standard Time 108 Daylight Saving Time Daylight Saving Time dC Off p Advanced Daylight Saving Time adjusts the time display to account for local Daylight Saving Time Selecting On adds one hour to the time display adjusted for your local time zone Selecting Off leaves the time display as adjusted for your local time zone This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode To change the Daylight Saving Time setting 1 Make sure you are in Advanced User Mode then highlight Daylight saving Time on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to turn Daylight saving Time On or Off Off On Default Off Position Format Advanced Position Format q dd mm mmm gt Position Format selects the format of the latitude and longitude position display This menu choice is availab
13. Default 1 second International Units only Default 16 ft 5 m NOTE During slow travel or drift setting both Trackpoint Interval and Track Min NOTE During slow travel or drift setting both Trackpoint Interval and Track Min Distance to small values will allow you to increase the track resolution Distance to small values will allow you to increase the track resolution 92 ar Color Range Track Color Range L Track Color Range allows you to set the depth range that will be displayed as black the deepest depth when Color By Depth is selected as the style for the current track see Navigation Menu Tab Current Track NOTE Only an optional purchase transducer with a 50 kHz frequency will allow you to track to 3 000 feet To change the Track Color Range 1 Highlight Track Color Range on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Track Color Range setting 50 to 3000 feet or 20 to 1000 meters International Units only Default 50 ft 20 m Map Datum d WGS 84 Default gt Map Datum allows you to change the map coordinate system used by the 900 Series to match those of a paper map Map Datum Advanced To change the Map Datum setting 1 Make sure you are in Advanced User Mode then highlight Map Datum on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Map Datum setting Default WGS 84 93 Course Project
14. ING EE E sadness dere aba E E EE E JZ Trolling Motor Transducer Options ccccsscsessessscstssesseessessesesseesssesseeeen 20 AlE 9 AEE e A EEA E EEEE 32 Test and Finish the Transducer Installation oo cece 20 AWAY Cursor Control KEY csacsssnsistessureasonsinesypsettsnuisetarbineedantuetianianastapen 33 a a OW SY e E A EE EEEE 33 E E EA O ESEA A AA A T 33 ii 531557 1_B Table of Contents RON EEE EE EEE A E E A 34 KARE O n E E EA EE E 34 A a E A E E A 34 ZOOM APH KEYS aiiin ae 35 Views 35 Views and IV lel OUI snc casrcestsenstenaapscasstanraeesausccsen esaehvvecsuen tease ecsuea staan 39 SUD COMO VO enimere aana Raa Anan 36 AVE E E E E E 3 A OW S E E E EEE 38 6 Beam Sonar ViIeW c ccccscsscsssscssessscsessssesssssssesssesssessssssesessssessessetessesseessees 39 Snapshot and Recording ViOW ccccescescescssessesseesesteseesesseeseaseseeseeseeseeseaneees 40 Bird s Eye ViQW uocceccsscccsscsssscssssssesessescssesssesssscssssesssssseesssceissesssessessseeesateeseeaees 44 Charverd s Eye Combo VIEW euenit 45 Chary Chant Combo VOW couiorresiiooriip sinerien E En 46 E E EAE AAEE A SAE 4 Chars D Combo VIEW svssuiessuensienaiesnsietanesn enai 48 AZ Combo VEW svssuiessnensienaieomai taio 49 Ciar Onen AUO sses E EE 50 Viewing Cartography 50 Navigation Waypoints Routes And Tracks eniros save Edit or Delete a WaypOInt cccccccsssssssssesesssscesesteseesssssessesceseeesees Navigate to a Waypoint or POSIION ccccccs
15. Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the NMEA Output to On or Off Off On Default Off 110 Sonar Sonar lt n 2 Sonar deactivates Sonar and removes the Sonar Views from the view rotation To turn Sonar on or off 1 Highlight Sonar on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the sonar to On or Off Off On Default On D X A ASS Cadviews F Visible Visible Views Menu Tab access the tabbed Main Menu System then press the RIGHT 4 WAY Cursor Control key until the Views tab is selected This menu tab allows you to set the available views to either hidden or visible in the view rotation The view will be removed from the view rotation if it is set to Hidden and will be displayed in the view rotation if it is set to Visible Visible Visible Visible Hidden Hidden Hidden Visible b i Visible Visible Hidden Hidden Hidden Views Menu From any view press the MENU key twice to The following views are available e 2D Sonar View e 2D Zoom View e 3D 2D Combo View e 6 Beam Sonar View e Snapshot and Recording View e Self Test View e Accessory Test View e GPS Diagnostic View e Bird s Eye View e Chart Bird s Eye Combo View e Chart Chart Combo View e Chart View e Chart 3D Combo View e Chart 2D Combo View To Change the View Status of Any View 1 Highlight the View main menu tab 2 Use the U
16. Up If your 900 Series doesn t power up use the Installation Guide that also comes with it for specific confirmation details making sure that e the power cable is properly connected to the 900 Series control head e the power cable is wired correctly with red to positive battery terminal and black to negative terminal or ground e the fuse is operational e the battery voltage of the power connector is at least 10 Volts Correct any known problems including removing corrosion from the battery terminals or wiring or actually replacing the battery if necessary 114 900 Series Defaults to Simulator with a Transducer Attached A connected and functioning transducer will cause the newly started 900 Series to go into Normal operating mode automatically If when you power up the 900 Series it goes into Simulator mode automatically even though a transducer is already connected this means that the control head is not detecting the transducer Perform the following troubleshooting tasks e Using the Installation Guide that also comes with your 900 Series check to make sure that the transducer cable is securely connected to the 900 Series Reconnect if necessary and power up the 900 Series again to see if this fixes the problem e Replace the non functioning transducer with a known good transducer if available and power up the control head again e Check the transducer cable Replace the transducer if the cab
17. You can delete the highlighted recording or all recordings using Delete Recording or Delete All Recordings from the Snapshot and Recording X Press menu Bird s Eye View Bird s Eye View shows a 3D perspective view of the track and the chart land contour from a point above and behind the boat the eye point As the boat turns the eye point moves to follow the boat Big Digits on this view provide digital data in a large easy to see format When you press the 4 WAY Cursor key in the Bird s Eye View the position of the eye point will shift This allows you to move and turn the eye point so that you can look off to the sides or even behind the boat Pressing the RIGHT or LEFT arrow keys on the 4 WAY Cursor key turns the eye point right or left while pressing the UP arrow key moves the eye point forward and pressing the DOWN arrow key moves the eye point backward Pressing the EXIT key moves the eye point back to its original position behind and above the boat 44 Bird s Eye View Course t 399 Q 25 42 567 W 080 13 337 Depth Speed of Boat Q Course Direction that boat is travelling Land Contours relative to North Reference ee O Latitude and Longitude Position of Boat pase Chart Bird s Eye Combo View Chart Bird s Eye Combo View shows both the Chart and Bird s Eye views in a combination split screen You can perform any of the functions for either of these views but only when the view you want t
18. a sonar side 2 Use the RIGHT 4 WAY Cursor Control key to initiate canceling Cape oe Waypoint 001 3 The Confirm dialog box will appear To cancel navigation press the RIGHT Cursor key once more To avoid canceling navigation press Navigation X Press Menu the LEFT Cursor key 71 Active Side Active Side allows you to select which side kp Active Side q Left b of a Combo View will be active key presses will only affect the active side of the screen When a menu is displayed the non active side of the screen will be grayed out at any other time a green arrow will point to the active side Combo Views usually display sonar on the left with charts or Bird s Eye usually on the right The Active Side menu choice is only available when a Combo View is active To select the Active Side 1 Highlight Active Side on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to change which side is active Left Right Default Right P Split Position 50 Split Position ii ikal Split Position allows you to adjust what percentage of the screen is taken up by the left side of any Combo View each view may be adjusted independently you must be in a specific view to adjust the screen size for that view The number setting indicates the percentage taken up by the left side of the Combo View selecting Left sets the left side of the screen to its smallest setting The Split Position menu choice is only av
19. activate MOB or modify the current route without first canceling MOB navigation The Off Course trigger is also disabled and the Off Course Alarm circle is not drawn Any press of the GOTO key or selection of a GOTO menu item will cause an error beep and a short message will be displayed to the user that will disappear after 2 seconds Activate MOB navigation Press and hold the GOTO key for more than 1 5 seconds to activate the Man Overboard MOB function 57 Cancel MOB navigation From the Navigation X Press menu select Cancel MOB and press the RIGHT Cursor key Canceling MOB navigation removes the route and any waypoints created using the GOTO key but does not remove any saved routes from memory MOB Navigation Course rt Bearing t b 54m N 25 43 109 Elapsed Time W 080 10 002 00 00 18 Target surrounding MOB waypoint 4 MOB waypoint T MOB at Position where man fell overboard lapsed time since MOB was activated Boat icon The Menu System The menu system is divided into easy to use menu modules The main components of the menu system are Start Up Options Menu Press the MENU key during the power up sequence to view the Start Up Options menu See Start Up Options Menu X Press Menu The X Press Menu allows you to access the settings that are changed frequently without having to navigate through the whole menu system Press the MENU key once to display the X Press Menu When
20. and Recording View only Pings Per Second allows you to specify the maximum ping rate for the sonar recording currently in progress from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are in Snapshot and Recording View and are actively recording not playing back To specify the pings per second 1 Highlight Pings Per Second on the Snapshot and Recording X Press menu and press the RIGHT 4 Way Cursor key to increase and decrease the number in the menu bar 1 AUTO Default AUTO Playback Speed optional purchase MMC SD Card Snapshot and Recording View only gt Playback Speed E Playback Speed allows you to specify the playback speed for a sonar recording from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are playing back a recording To specify playback speed 1 Highlight Playback Speed on the Snapshot and Recording X Press menu and press the LEFT or RIGHT 4 Way Cursor key to display the following Playback Speed submenu choices which are represented by icons Beginning Rewind2 Rewind Reverse Normal Reverse Slow Pause Slow Play Normal Play FF FF2 End NOTE You can also change playback speed in the Snapshot and Recording View using the Left and Right 4 Way Cursor keys although you cannot skip to the beginning or end of a recording us
21. be updated more slowly while maintaining the 3D data display Select 3D when you want to see the most detailed 3D information 2D information will be updated most slowly with this choice To change the 2D 3D Priority P Active Side Navigation X Press Menu 1 Highlight 2D 3D Priority on the 3D Sonar X Press menu TERE B gt The Navigation X Press Menu provides access to the settings most frequently used Press the MENU key once while in the Bird s Eye View the Chart or the Chart Sonar o Save Current Track Combo Chart Chart Combo View or Xi Cancel Navigation Cancel Navigation Chart Bird s Eye Combo View to access the gt only when Navigating Navigation X Press Menu Cancel Navigation discards the current route and exits Navigation Mode El Save Current Route This menu choice will only appear when you are currently navigating a route A Skip Next Waypoint 50 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Waypoint 001 2D 3D Priority 2D Only Equal 3D Default 3D NOTE Menu choices will vary depending on system settings such as whether you are This will not delete a previously saved route currently navigating Xs Cancel Navigation To Cancel Navigation NOTE You will have to change Active Side i Cancel MOB Navigation ation X 1 Highlight Cancel Navigation on the 2D Sonar X Press menu setting to Hight to see the Navigation XPress Menu from a Combo View with
22. cable to the control head k You may route the cable over the top of the transom or drill a 5 8 16 mm diameter hole in the transom directly above the sensor and above the waterline to route cable through Use the cable clamps provided to secure the cable to the transom of the boat If you use a through hole then also use the included escutcheon plate to dress the hole NOTE On fiberglass hulls it is best to start with a smaller drill bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating 2 All mounting screws not specified require a 9 64 3 5 mm pilot hole drilled approximately 5 8 16 mm deep Additionally seal any hole drilled in the transom of the boat with marine grade silicone sealant not included 3 Route the cable to the Control Head and insert the connector into the appropriate slot Use the connector designated for accessories on the control head NOTE The speed accessory will be detected only if the paddlewheel has moved since your 900 Series was powered up 4 Ifthe connections are correct the Control Head will begin displaying water temperature information immediately assuming that the control head is powered on If the gauge fails to read properly at high speeds adjust the height of the sensor on the transom Testing the System Installation After you have completed the installation of the control head transducer and any other accessories suc
23. for all depth related readouts To change the Units Depth setting 1 Highlight Units Depth on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Units Depth setting Meters nternational models only Feet Fathoms Default is Meters for International models and Feet for Domestic models Units Temp Units Temp 4 ili b International only Units Temp selects the units of measure for all temperature related readouts nternational models only To change the Units Temp setting 1 Highlight Units Temp on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Units Temp setting Celsius Fahrenheit Default Celsius Units Distance Units Distance d Feet Statute Miles gt with Speed input only Units Distance selects the units of measure for all distance related readouts To change the Units Distance setting 1 Highlight Units Distance on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Units Distance setting Domestic Models Statute Miles Nautical Miles Default Statute Miles International Models Meters Kilometers Meters Nautical Miles Feet Statute Miles Feet Nautical Miles Default Meters Kilometers Units Speed Units Speed q mh p with Speed input only Units Speed selects the units of measure for speed related readouts To change the Units Speed setting 1 Highlight Units Spe
24. have a trolling motor transducer there are several options e You may purchase a Trolling Motor Adapter kit that will allow you to mount the transducer on the trolling motor e You may also exchange your NEW and UNASSEMBLED transducer with mounting hardware included for a trolling motor transducer There are also several transducer switches available that support the following configurations e Two control heads with one transducer e Two transducers with one control head NOTE Call the Humminbird Customer Resource Center at 1 800 633 1468 for details and pricing or visit www humminbird com for more information 20 Test and Finish the Transducer Installation When you have installed both the control head the transom transducer and accessories and have routed all the cables you must perform a final test before locking the transducer in place Testing should be performed with the boat in the water although you can initially confirm basic operation with the boat out of the water NOTE If you have installed an in hull mount transducer this procedure does not apply as the transducer is already locked in place 1 Press POWER once to turn the control head on There will be an audible chirp when the button is pressed correctly If the unit does not power up make sure that the connector holder is fully seated and that power is available If all connections are correct and power is available the control head will enter N
25. information Low Battery Alarm Aux Temp Alarm Temp Alarm 8 Off Course Alarm 300ft Arrival Alarm 150ft Oo Main Menu System Normal User Mode NOTE The Main Menu choices will vary depending on whether you are in Normal or Advanced User Mode and what model you own User Mode Normal or Advanced An Advanced Mode is provided for users who desire the highest level of control over the 900 Series and Normal Mode for users who desire greater simplicity and fewer menu choices Additional Advanced menu choices will be displayed throughout the menu system when you navigate to specific menus while in Advanced Mode Any changes made while in Advanced Mode will remain in effect after you switch back to Normal Mode See Setup Menu Tab User Mode for specific instructions on changing to the User Mode NOTE The 900 Series defaults to Advanced User Mode on start up Co XZ 1X Thad 3 setup L Units Depth Units Distance Units Speed User Mode 4 Normal gt Triplog Reset Restore Defaults Sonar Tab Normal Mode a LS 3 Setup Units Depth Units Temp F Units Distance Statute Miles Units Speed mp User Mode Advanced Language English Triplog Reset Restore Defaults Select Readouts Depth Offset 0 0ft Aux Temp Offset 0 Speed Calibration 0 Local Time Zone EST UTC 5 Daylight Saving Time h 0 Temp Offset 0 0 Off Position For
26. is a user controllable audible alert that sounds when the water surface temperature equals the setting Backlight Backlight is a user controllable illumination for the LCD for night and low light use Beam Sonar Beam A sonar beam is the wide cone shaped projection of sound waves formed as sound travels underwater See Cone Angle Big Digits View Big Digits View is a Humminbird feature that displays the sonar graph and enlarged digital readouts for easy reading from a distance This is a great tool when monitoring the digital depth is important such as with higher boat speeds or when viewing the unit from a distance When speed input is available the Big Digits View also shows the TripLog See TripLog Bottom Black Bottom Black is a Humminbird feature that fills in the area of the display below the bottom contour Bottom Black is preferred by some anglers because of its high contrast and easy readability even though it can obscure bottom hardness information Bottom Contour Bottom Contour is the profile of the bottom graphed to the display as the depth changes Bottom Hardness Bottom Hardness is the density or composition of the bottom which can often be determined by interpreting the main sonar return Varying levels of hardness can be determined by interpreting the thickness of the sonar return Hard returns appear thin and black softer returns appear thicker and less black It is important to note that a sonar ret
27. is set to 58 degrees Fahrenheit and the water temperature falls from 60 degrees to 58 degrees the Aux Temp Alarm will sound Similarly if the water temperature rises from 56 degrees to 58 degrees the Temp Alarm will also sound To change the Aux Temp Alarm setting 1 Highlight Aux Temp Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 Way Cursor Control keys to change the Aux Temp Alarm setting Off 33 120 Fahrenheit 0 50 Celsius Default Off 100 Temp Alarm off Temp Alarm off 120 Temp Alarm sounds when the water temperature detected by the 900 Series reaches the Temp Alarm setting which is either set in degrees Fahrenheit or Celsius nternational models only For example if the Temp Alarm is set to 58 Fahrenheit and the water temperature falls from 60 to 58 the Temp Alarm will sound Similarly if the water temperature rises from 56 to 58 the Temp Alarm will also sound To change the Temp Alarm setting 1 Highlight Temp Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 Way Cursor Control keys to change the Temp Alarm setting Off 32 120 Fahrenheit 0 50 Celsius International models only Default Off ey Course Alarm 300ft Off Course Alarm Of TD 3000 Off Course Alarm sounds when the boat has moved too far off course based on the menu setting when navigating Off Course Alarm allows you to set how far the boat is allowed to move off course before the Off Course Alarm
28. location e Observe the outside of the boat hull to find the areas that are mostly free from turbulent water Avoid ribs strakes and other protrusions as these create turbulence e As a general rule the faster the boat can travel the further aft and closer to the centerline of the hull the transducer has to be located in order to remain in contact with the water at high speeds Trial installation You will not be able to adjust the mounting after an inside the hull transducer is installed It is best therefore to perform a trial installation first that includes running the boat at various speeds in order to determine the best mounting area before permanently mounting the transducer 1 2 Plug the transducer into the control head then power up the control head When the control head detects a functioning transducer it will automatically enter Normal operating mode View the sonar signal at its best by holding the transducer over the side immersed in the water so that it is pointing straight down over a known flat bottom Use the display to benchmark against the sonar signal that will be detected once the transducer is placed in the hull Place the transducer body face down at the identified mounting location inside the hull with the end that has the mounting ears pointed towards the bow of the boat Fill the hull with enough water to submerge the transducer body Use a sand filled bag or other heavy object to hold
29. m Each transmitted beam is 16 degrees in width and is symmetrical The six beams are lined up next to each other to provide a total coverage of 53 degrees from side to side and 16 degrees from front to back Using multiple narrow beams together gives you a wide area of coverage for terrain interpretation and fish location without sacrificing the detail only a narrow beam can provide Your 900 Series Fishing System gathers information from a continuous series of these returned signals It then interprets this information to create a detailed 3 dimensional view of the terrain passing beneath your boat as you travel across the water 53 Degree Total Coverage 3D Bottom Coverage 1 x Depth 2D Sonar Your 900 Series Fishing System also has the capability of displaying traditional 2 dimensional sonar information from either a 455 kHz beam or an 83 kHz beam The 455 kHz single beam has the advantage of providing increased sonar resolution but is limited to a depth capability of 240 ft 75 m The 83 kHz single beam sonar has the advantage of providing sonar information to 1000 ft 330 m but the sonar resolution is not as great as with the 455 kHz single beam How GPS and Cartography Work Your 900 Series Fishing System also supports GPS and chartplotting and uses GPS and sonar to determine your position display it on a grid and provide detailed underwater information The Global Positioning System GPS is a satellite navigat
30. narrow beams will be displayed in all views and the maximum depth capability of your unit will be 240 ft 75 m When set to 83 kHz the returns from the 83 kHz wide beam will be displayed in all views except for the 3D 2D Combo View which will continue to display returns from both beams in their respective windows The RTS Window will display the returns from the 83 kHz wide beam NOTE Itis important to re set 2D Beam Select to 455 kHz when returning to water shallower than 240 ft 75 m for maximum performance in the 3D views 82 To change 2D Beam Select 1 Highlight Beam Select on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to select either the 455 kHz beam or the 83kHz beam 455 kHz 83 kHz Default 459 kHz Fish ID Fish ID 3D Markers _ Fish ID uses advanced signal processing to interpret sonar returns and will display a Fish Symbol when very selective requirements are met When a fish is detected a fish icon and its depth are displayed above the return that has been classified as being a fish Fish symbols come in three different sizes to indicate the intensity of the return in addition there is a unique symbol set associated with each of the six beams for a total of 18 possible fish symbols which can be displayed The following graphic illustrates the different Fish ID symbols and shows the beams with which they are associated For instance a hollow fish facing left
31. o addition to the Basic Navigation and Underwater information Penney h Map Borders shown with Optional Purchase Navionics Cartography To change the Chart Detail Level setting 1 Highlight Chart Detail Level on the Navigation main menu EEE ae seen 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Er F Chart Detail Level setting Basic Navigation Underwater All F Default All SPEED Imphl4 homo 2 a Oy NOTE Some chart details are only available with optional purchase MMC SD 7 cards Map Borders To change the Map Borders setting 1 Highlight Map Borders on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Map Borders setting Hidden MMC SD Only All Visible Default MMC SD Only 95 a Grid Lat Lon Grid ER Lat Lon Grid allows you to display or hide a grid showing latitude and longitude lines To change the Lat Lon Grid setting 1 Highlight Lat Lon Grid on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Lat Lon Grid setting Hidden Visible Default Hidden Soundings Spot Soundings EEE Spot Soundings allows you to display or hide spot soundings which are depth measurements shown on the chart NOTE Spot Soundings are only available with optional purchase MMC SD cards To change the Spot Soundings setting 1 Highlight Spot Soundings on the Navigation main menu 2 Use the LEFT or
32. of the left side of a split screen see 2D Sonar X Press Menu Split Position or Navigation X Press Menu Split Position for more information NOTE See 2D Sonar View and Chart View for more information about each side of this view 49 Chart 2D Combo View Depth Course Direction that boat is travelling relative to North Reference 5 O Boat Icon Cartography O Track Sonar Window Map Scale Chart Window Chart Orientation All the chart views allow you to choose the orientation of the chart When North Up orientation is selected True North is shown at the top of the display In other words objects located to the north of the boat are drawn above the boat When Course Up orientation is selected the direction of motion of the boat is shown at the top of the display In other words objects ahead of the boat are drawn above the boat In both orientations the view pans automatically so that the boat is always centered on the display When the boat is stationary it is drawn as a circle When the boat is in motion it takes on a boat shape pointed in the direction of motion always Up in the Course Up orientation See Navigation Menu Tab Chart Orientation for more information Viewing Cartography In the Chart or Combo Views there are several cartography related functions that you can access using various keys Panning Use the 4 WAY Cursor keys to move the chart around on the display in the direction of the
33. on a Map along with Tracks Waypoints and Routes All Chartplotters are also considered Trackplotters All Humminbird GPS Combo units are Chartplotters See rackplotter Glossary Cold Start Cold Start refers to the procedure that a GPS receiver must perform when it does not have historical information regarding its current location This procedure typically lasts for several minutes and may be experienced upon first power up of the receiver or if the receiver has been moved a great distance Course Over Ground COG Course Over Ground is the current direction the boat is traveling measured in degrees from North i e 321 where 000 is North 090 East 180 is South 270 is West When the Course Over Ground is equal to Bearing the boat is said to be On Course and will arrive at the destination in the most efficient manner COG Is often confused with Heading See Heading Cross Track Error XTE Cross Track Error is the straight line distance of the boat from the intended Track XTE measures how far the boat is off course and also triggers the Off Course Alarm See Track Differential GPS DGPS Differential GPS is a system to improve the position accuracy of the Department of Defense GPS through the use of secondary correction signals broadcast from ground stations around the coastal United States and on some inland waterways These correction signals are provided by the USCG and received by an auxiliary Differe
34. on the Setup main menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate this procedure 3 The Select Readouts submenu will appear showing a list of all Readouts Use the UP or DOWN Cursor keys to select a particular Readout position then use the RIGHT or LEFT Cursor keys to change what will be displayed at that position Aux Temperature Course Depth Off Position Speed Temperature Time Time Date Triplog Voltage Water Speed Depth Offset 0 0ft Depth Offset 10 0 i o Advanced Depth Offset will adjust the digital depth readout to indicate depth from the waterline or boats keel Enter a positive vertical measurement from the transducer to the waterline to read the depth from the waterline Enter a negative vertical measurement from the transducer to keel to read the depth from the keel This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Made To change the Depth Offset setting 1 Make sure you are in Advanced User Mode then highlight Depth Offset on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Depth Offset setting 10 0 to 10 0 feet or 3 to 3 meters International models only Default 0 0 or Off 107 Aux Temp Offset 0 0 Aux Temp Offset 10 0 oo Advanced Aux Temp Offset will adjust the aux temperature readout the temperature on the optional purchase temperature probe or Iemp Speed accessory by the amount entere
35. or accessories by unauthorized individuals will void the warranty Handling and or opening this unit may result in exposure to lead in the form of solder WARNING This product contains lead a chemical known to the state of California to cause cancer birth defects and other reproductive harm NOTE Some features discussed in this manual require a separate purchase and some features are only available on international models Every effort has been made to clearly identify those features Please read the manual carefully in order to understand the full capabilities of your model 900 Series Cannon CannonLink DualBeam PLUS Fish ID HumminbirdPC Humminbird InterLink One Touch Zoom RTS Window SmartCast Structure ID Total Screen Update TrueArch WeatherSense WhiteLine WideSide X Press and X Press Menu are trademarked by or registered trademarks of Humminbird 2007 Humminbird Eufaula AL USA All rights reserved Table of Contents 900 Series Introduction 1 GPS Receiver Installation 21 How the 900 Series Works ou cescessescsscssessecseesesceseeseeseeseesesteseeseeseeseereaesees 1 stem Mounting with an Existing 1 14 Thread Stem uu 22 D tees cece E ere EEE E ERES 2 Access Under Mounting Location c cccccccscecessessesesteseeseseesestesteseensacereaees 23 A O e E EE ee eet ee eet eee 2 No Access Under Mounting Location c cccccecscescssestesteseetesesesteseeeatee
36. other end of the transducer cable 5 8 18 mm hole back into the control head connection holder Escutcheon Plate Cable Clamp Perform a final test of the transom transducer installation After transom transducer installation please perform the final testing and then finalize the installation see Jest and Finish the Transducer Installation Inside the Hull Transducer Installation If you choose to mount your transducer inside the hull of your boat perform the procedures in this section In hull mounting generally produces good results in single thickness fiberglass hulled boats Humminbird cannot guarantee depth performance when transmitting and receiving through the hull of the boat since some signal loss occurs The amount of loss depends on hull construction and thickness as well as the installation position and process This installation requires slow cure two part epoxy Do not use silicone or any other soft adhesive to install the transducer as this material reduces the sensitivity of the unit Do not use five minute epoxy as it has a tendency to cure before all the air bubbles can be purged thus reducing signal strength NOTE In hull mounting requires an installed and operational control head Preferred Mounting Area O Fivets Strakes O Step Determine the transducer mounting location Decide where to install the transducer on the inside of the hull Consider the following to find the best
37. slowly while maintaining the 3D data display select 3D when you want to see the most detailed 3D information 2D information will be updated most slowly with this choice To change the 2D 3D Priority 1 Highlight 2D 3D Priority on the 2D Sonar X Press menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 2D 3D Priority 2D Only Equal 3D Default 3D Cancel Navigation gt only when Navigating S Cancel Navigation Cancel Navigation discards the current route and exits Navigation Mode This menu choice will only appear when you are currently navigating a route This will not delete a previously saved route To Cancel Navigation 1 Highlight Cancel Navigation on the 2D Sonar X Press menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate canceling navigation 3 The Confirm dialog box will appear To cancel navigation press the RIGHT Cursor key once more To avoid canceling navigation press the LEFT Cursor key 67 3D Sonar X Press Menu 3D Sonar Views only WP Active Side 4 Right b Pe 3 So EPan Hom po 50 The 3D Sonar X Press Menu provides v4 6 Beam Sensitivity o access to the settings most frequently used Q 3D Bottom Zoom Press the MENU key once while in any of the 3D Sonar Views to access the 3D Sonar E gt 3D Lower Range X Press Menu Auto NOTE Menu choices will vary depending on 4 system settings such as whether the unit is set for Advanced Use
38. so the face of the transducer is 1 8 3 mm to 1 4 6 mm beneath the bottom of the transom and fully tighten the three mounting screws 4 In order to gain access to the mounting screws the transducer Route the transom transducer cable ee i be pivoted p in the pace as shown ue The transducer cable has a low profile connector that must be routed to the not to i e running angie as some torce Is necessary to pivot the point where the control head is mounted There are several ways to route the assembly transducer cable to the area where the control head will be installed The most common procedure routes the cable through the transom into the boat Tighten the Pivot Screws Tighten the Mounting Screws NOTE Your boat may have a pre existing wiring channel or conduit that you can use for the transducer cable 1 Unplug the other end of the transducer cable from the control head Make sure that the cable is long enough to accommodate the planned route by running the cable over the transom CAUTION Do not cut or shorten the transducer cable and try not to damage the cable insulation Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference If the cable Is too short extension cables are available to extend the transducer cable up to a total of 50 15 m For assistance contact the Customer Resource Center at www humminbird com or call 1 800 633 1468 for more infor
39. submenu select Edit and press the RIGHT Cursor key A Route Edit screen will be displayed Select the route you wish to edit and press the RIGHT Cursor key Re name the route or change delete or re order the waypoints used in the route Delete a saved route From the Routes submenu select Delete and press the RIGHT Cursor key Select the route you wish to delete and press the RIGHT Cursor key You will be asked to confirm your choice by pressing the RIGHT Cursor key again before the route is deleted Travel a saved route From the Routes submenu select Travel and press the RIGHT Cursor key A list of saved routes will appear Select the route you wish to travel and press the RIGHT Cursor key to make this route the current route and begin navigation You may also travel the route in either forward or reverse order Route Info From the Routes submenu select Info and press the RIGHT Cursor key A list of saved routes will appear Select the route for which you want information and press the RIGHT Cursor key The list of waypoints in the route will be shown with the distance and bearing from each waypoint to the next as well as the distance and bearing from the current position to the first waypoint in the route Save or Clear a Current Track Save the current track From the Navigation X Press Menu select Save Current Track and press the RIGHT Cursor key The track will remain on the display but will change from black to gray To rem
40. tartan 88 Temperature Graph 2D Sonar View only with Temperature input c cccccccccseesee 88 Navigation Menu Tab 88 Current TACK oo eceesceccsesscesssesessesssscesssessessssvcsessssesssasssesussssetsucseeesaessesesseeseaesees 89 Saved TACKS cessccccssessscsessessesssseesessesesssssssesssssesssussessesssssessesseeesaesseeeseeeeeaeeaes 89 NU WSIS aca arenas E EAEE AN AA EE A EEE 90 FOUTS OAA E AEN EEA AA A A 90 Civ T O eee ER EE EE E 91 North VETOES sa ascscnncateanssceiaavouceutsugesantvsaiettiase a a 91 Tono Gnd ROLAU roen E T 91 ADAG KOE INMETA renina 9 Track Min Distance Advanced cccccccccccccscscsesssesesesesesessesesnstsesesesereevieeseeeen 9 Tack Color Ranga cae setecescte te ceence ect anenee dees ence eect acta eter este 93 Map Vaitinmi Aane sian 93 Table of Contents Goune Projgcion WN recen 93 Export All Nav Data Advanced 93 Dete AW INAV Data AQVAICOO x csintcscstscccetetesxocstuareadeienarstiaineeosmcteiteriontein 94 Continuous Navigation Mode cccecccccsccssesssessesssessseesesssescsssestsnsseeseees 94 Chart Menu Tab 94 Ghart Detall LEVET sccecassensaancoresenesanansiesiareieeaeivdesaanbeeheicseonvsataeugnveeart 95 VIO BONGO P S EE VE EE S 95 Pe EA aE E A E AA E E S 96 PON OO MMMM EEE E E E T 96 Navaids On Bird s Eye ViQW u ccccsceccscesescssscssscsssescessseessseessscstessstessateesaaees 96 Shaded Depth cece cccecsccsccsssesssseesesssessseesessssessesssseesssessessesseesssessessaesseaess 96
41. the sonar system which mounts on the boat and is in contact with the water that converts the electrical energy from the transmitter into sound energy and that forms the sonar beam in turn Internally the transducer consists of one or more piezo electric disks that expand by very minute amounts to create the sound wave This element also works in reverse converting the returned sound energy back into an electrical signal that the receiver interprets Transducers are available for many specific mounting applications for the boat such as a transom mount trolling motor mount etc Humminbird offers many sophisticated transducers often with multiple piezo electric elements designed to form specifically shaped sonar beams providing the angler with superior tools for finding and catching fish See 7ransmitter and SONAR Transmitter The transmitter and receiver are matched parts of the sonar system that send transmit and listen to receive the sonar signals and work in conjunction with the transducer Humminbird transmitters have an extremely fast cycling design that can send signals up to 60 times per second as well as produce the varying levels of power output needed for different depths and conditions Additionally the transmitter has the capability to create very precise sonar pulses needed for a high degree of target separation Humminbird receivers are extremely sensitive but within a narrow bandwidth to discriminate against noise
42. the stainless steel mounting bracket screws to secure in place Hand tighten only 21 GPS Receiver Installation To optimize performance of the GPS receiver mount it in an area that has full exposure to the sky The effective area of reception is 10 above the horizon Different circumstances determine the mounting method appropriate for your GPS receiver If you have An existing antenna stem with standard 1 14 thread stem Access for cable routing under the mounting location No access under the mounting location Then use Stem Mount with Existing 1 14 Thread Stem Access Under Mounting Location No Access Under Mounting Location The pinouts of the pigtail cable are as follows e Red Wire 12V output voltage only e Black Wire Ground e White Wire NMEA Out CAUTION Please use caution before connecting the red 12V wire to any other NMEA device This is an output voltage provided by the Fishfinder unit and GPS receiver and should only be connected to those NMEA devices that need a 12 volt input Stem Mounting with an Existing 1 14 Thread Stem 3 Use electrical tape to secure the NMEA pigtail to the cable as shown Follow these steps to stem mount the GPS receiver B NOTE Leave the NMEA pigtail secured to the cable unless needed This will NOTE If you have an existing stem for mounting the GPS receiver proceed make removing the receiver easier directly to step 2 of the following pr
43. the transducer in position The transducer cannot transmit through air and the water purges any air from between the transducer and the hull and fills any voids in the coarse fiberglass surface Transducer Mounted Inside the Hull View the sonar signal on the display and compare against what you observed in Step 2 making sure that the boat is in the same location as it was during your observations in Step 2 If the results are comparable move on to Step 6 Otherwise locate a new position in the hull and repeat Steps 3 through 5 Run the boat at various speeds and water depths while observing the screen on the control head If depth performance is required test the transducer in water at the desired depth If the performance is acceptable move on to Step 7 If the performance is not acceptable repeat Steps 3 through 6 7 Once you have determined the best mounting location using the 5 Coat the face of the transducer and the inside of the hull with epoxy above steps mark the position of the transducer l _ l 6 Press the transducer into place with a slight twisting motion to purge any trapped air from underneath keeping the end of the Route the cable transducer that has the mounting ears pointed forward towards the 1 Once the mounting location is determined and you have marked the bow of the boat position of the transducer route the cable from the transducer to iherconiral head NOTE Proper operation requires the end o
44. to quickly move the cursor to any saved waypoint so that you can locate it or edit it NOTE This X Press menu item appears only if you have saved waypoints To move cursor to a saved waypoint 1 Highlight Cursor to Waypoint on the Navigation X Press menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate Cursor to Waypoint 3 Use the UP or DOWN 4 WAY Cursor Control key to highlight the waypoint you wish to move the cursor to then use the RIGHT 4 WAY Cursor Control key to select the destination waypoint IE Eacan Save Current Track Save Current Track 2 Save Current Track allows you to save the current track being displayed After the current track is saved a new current track is started To Save Current Track 1 Highlight Save Current Track on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate saving the current track 3 The Confirm dialog box will appear To save the current track press the RIGHT Cursor key once more To cancel saving the current track press the LEFT Cursor key pene ete om Clear Current Track Clear Current Track Clear Current Track allows you to clear the current track being displayed and start a new track at the present position To Clear Current Track 1 Highlight Clear Current Track on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate clearing the current track 3 The Confirm dialog box will appear
45. waypoint on the Combo and Chart Views You can exit these fields with the LEFT and RIGHT Cursor keys or by pressing the EXIT key Select Save and press the RIGHT Cursor key to save your changes To make it easier to select a waypoint select Sort By and press the RIGHT or LEFT Cursor keys to select a sort order e Name shows the waypoints alphabetically e Time shows the most recently created waypoint first e Distance shows the closest waypoint first Delete a waypoint From the Waypoints submenu select Delete and press the RIGHT Cursor key to display a list of waypoints Select the waypoint you want to delete then press the RIGHT Cursor key You will be asked to confirm deletion before the waypoint is actually deleted Navigate to a Waypoint or Position Navigate to the cursor position From any Chart or Combo view use the Cursor key to select a position or waypoint to which you want to navigate Press the GOTO key Navigation will begin immediately Navigate to a specified waypoint Press the GOTO key then choose the waypoint to which you would like to navigate from the waypoint list and press the RIGHT Cursor key to select it NOTE By repeating the previous instructions you can add more waypoints to create a longer multi segment route Skipping a waypoint From the Navigation X Press Menu select Skip Next Waypoint and press the RIGHT Cursor key If there is not another waypoint to skip to navigation will be cancelled
46. will sound Off Course Alarm Off Course Limits Ariival Alarm Circle To change the Off Course Alarm setting 1 Highlight Off Course Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Off Course Alarm setting Off 25 to 3000 feet 10 to 1000 meters International models only Default 300 ft 100 m 101 Arrival Alarm 164ft Arrival Alarm Off a 3000 Arrival Alarm sounds when the boat has either exceeded the distance to the destination waypoint or has entered the Arrival Alarm Circle based on the menu setting when navigating Arrival Alarm allows you to set how close the boat must be to the destination waypoint before the Arrival Alarm will sound To change the Arrival Alarm setting 1 Highlight Arrival Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Arrival Alarm setting Off 25 to 3000 feet 10 to 1000 meters International models only Default 150 ft 50 m ee Alarm off Drift Alarm a a Alarm Tone Of ES 3000 Drift Alarm sounds when the boat has l Alarm Tone selects the pitch of the alarm exceeded the distance from the boat s anchored position based on the sound A brief tone will be produced as you adjust the Alarm Tone so that menu setting Drift Alarm allows you to set the size of a perimeter around the you can select the tone that you can hear best boat s anchored position if the anchored boat drifts outside o
47. 25 mm hole routing the cables through the grommet and pressing the grommet into place Place the hole cover over the mounting surface hole then use it to mark the position of the two mounting screws Remove the hole cover drill the two mounting holes using a 9 64 3 5 mm bit fill them with marine grade silicone then replace the hole cover and insert the 8 Phillips countersink wood screws Hand tighten only Place the mounting bracket on the mounting surface aligned with the drilled holes and fill the mounting holes with marine grade silicone Insert the four 10 Slotted Hex wood screws into the mounting holes Hand tighten only If the cable pass through hole is beneath the mounting bracket you will need to install the hole cover Place the hole cover over the mounting bracket cable pass thru hole and align with holes drilled in step 6a Insert the 8 Phillips countersink wood screws Hand tighten only NOTE Be sure that the cables pass through the slots on the hole cover and there Is enough cable slack to allow for the control head to pivot through its full tilt range Extra cable slack will also helo when connecting aisconnecting the cables Gimbal Bracket Hole Cover Cables Routed Directly Beneath Mounting Bracket ps ct Cables Routed Behind Mounting Bracket wore tre a N UA OCCU G TW ccc i V GEN Gimbal Bracket Grommet Hole Cover 9 Insert cable connectors into the p
48. 4 WAY Cursor Control key to change the size of the left side of a Combo View Left 30 40 50 60 70 Right Default 50 6 Beam Sensitivity 6 Beam Sonar View only 4 6 Beam Sensitivity 10 120 6 Beam Sensitivity controls how much detail is shown on the display and is only available when you are in the 6 Beam Sonar View Increasing the sensitivity shows more sonar returns from small baitfish and suspended debris in the water the display may become too cluttered however When operating in very clear water or greater depths increased sensitivity shows weaker returns that may be of interest Decreasing the sensitivity eliminates the clutter from the display that is sometimes present in murky or muddy water If Sensitivity is adjusted too low the display may not show many sonar returns that could be fish To adjust the 6 Beam Sensitivity 1 Highlight 6 Beam Sensitivity on the X Press menu while in the 6 Beam Sonar View 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to increase or decrease the 6 Beam Sensitivity setting Low 1 High 20 Default 10 69 3D Bottom Zoom 3D Bottom Zoom i gt 3D Bottom Zoom provides a magnified image of the bottom and is only available on the 3D Sonar X Press Menu in the 3D Sonar View and the 3D 2D Sonar Combo View Use 3D Bottom Zoom to increase the detail of the bottom on the display To adjust the 3D Bottom Zoom 1 Highlight 3D Bottom Zoom on the 3D Sonar X Press Menu
49. 633 1468 By e mail typically we respond to your e mail within three business days custserv johnsonoutdoors com For direct shipping our address is Humminbird service Department 678 Humminbird Lane Eufaula AL 36027 USA YHUMMUNBIRD 135
50. 83ft Speed 5 6mph Course o t WEST 080 13 349 Depth T9704 11 36 10 aar Sky Chart Current Latitude and Longitude Satellite Being Used Satellite Being Monitored 4 Left 50 va Sensitivity 10 Upper Range oft gt Lower Range Auto X Chart Speed 5 E Bottom Lock Off gt Bottom Range 15ft V2 2D 3D Priority 3D 2D Sonar X Press Menu 2D Sonar X Press Menu 2D Sonar Views only The 2D Sonar X Press Menu provides access to the settings most frequently used Press the MENU key once while in any of the 2D Sonar Views to access the 2D Sonar X Press Menu NOTE Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode or whether a 2D or a 3D View is currently displayed active 63 Active Side Active Side allows you to select which side of a Combo View will be active key presses will only affect the active side of the screen When a menu Is displayed the non active side of the screen will be grayed out at any other time a green arrow will point to the active side Combo Views usually display sonar on the left with charts or Bird s Eye usually on the right The Active Side menu choice is only available when a Combo View is active WP Active Side q Left p To select the Active Side 1 Highlight Active Side on the 2D Sonar X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to change wh
51. Cancel navigation From the Navigation X Press Menu select Cancel Navigation and press the RIGHT Cursor key Canceling navigation removes the route and any waypoints created using the GOTO key but does not remove any saved routes from memory You will be prompted to save the Current route when you cancel navigation 54 Add a Waypoint Target or Trolling Grid Add or Remove a Waypoint Target From the Waypoints submenu accessed from the Navigation main menu select Target and press the RIGHT Cursor key to display a list of waypoints Select the waypoint you want to target A target consisting of concentric circles centered on the selected waypoint will appear on all of the navigation views the target shows various distance ranges from the targeted waypoint To remove the target choose Remove Target from the Navigation X Press Menu NOTE Only one waypoint can have either a target or a grid at one time If you apply a target or a grid to a new waypoint the original waypoint will lose its target or grid Chart View with Target Wap Scale Waypoint Target Add or Remove a Trolling Grid From the Waypoints submenu accessed from the Navigation main menu select Grid and press the RIGHT Cursor key to display a list of waypoints Select the waypoint to which you want to add the grid The trolling grid will appear on all of the navigation views and can be used as a guide when trolling around a waypoint The grid can be rotated t
52. Date o Off e Triplog e Position e Voltage e Aux Temperature e Temperature e Speed e Water Speed Sonar only Views Not Navigating On Sonar only views as long as you are not navigating all 5 readouts are customizable Other Views Not Navigating On any view with a chart as long as you are not navigating two of the readouts are not customizable the 2nd box always displays Heading while the 5th box always displays Speed On the Bird s Eye View when you are not navigating there are four fixed info boxes that show Depth Heading Position Lat Lon and Speed When you are navigating in the Bird s Eye View there are two columns of four boxes The first column shows Depth Time To Go TTG Position Lat Lon and Speed The second column shows Cross Track Error XTE Heading Bearing and Distance To Go DIG All Views Navigating When you are navigating all readouts in all views even split screen views with a Sonar display cannot be customized with the exception of the top readout info box which is still customizable In any view while you are navigating the second readout box shows Heading the third box shows Bearing the fourth box is divided to show Cross Track Error XTE and Distance To Go DIG and the fifth box is divided to show Time To Go TTG and Speed 106 Default Sonar View Customized Sonar View To Select Readouts 1 Make sure you are in Advanced User Mode then highlight Select Readouts
53. FT Cursor key a Defaults Restore Defaults D Restore Defaults resets ALL menu settings to their factory defaults Use this menu choice with caution To Restore Defaults 1 Highlight Restore Defaults on the Setup menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate restoring defaults 3 The Confirm dialog box will appear To reset the defaults press the RIGHT Cursor key once more To cancel Restore Defaults press the LEFT Cursor key Select Readouts Select Readout 1 Readouts 4 Depth p Advanced Readout 2 Select Readouts allows you to customize the Triplog information displayed in individual digital readouts on Readout 3 the left side of many views including suppressing a WeatherSense particular readout so that nothing is displayed the ability to customize readouts depends on the view Temperature and whether you are navigating This Advanced Readout 5 feature allows you to select what data will be Speed displayed in each of 5 fixed position data windows arranged at the left edge of the Sonar View screen or whether a particular data window will be turned off displaying nothing in that area you can access this menu choice only when in Advanced User Mode see Setup Menu Tab User Mode Select Readouts Data windows can display readouts from supported accessories such as a speed accessory Each data window can either be empty Off or contain one of the following e Course e Time e Depth e Time
54. MENU key twice to access the 3D Bottom Style Shaded with Grid Main Menu System and then press the RIGHT Cursor key to select the Sonar tab 81 eg 2D Sonar Colors 2D Sonar Colors Standard angar p 2D Sonar Colors allows you to select which color palette you would like to use for the display To change the 2D Sonar Colors 1 Z Highlight 2D Sonar Colors on the 2D Sonar menu Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the color palette Standard Gray Inverse Green Default Standard Bottom Style 3D Bottom Style 4 Shaded swith Gridp 3D Bottom Style selects the bottom style used in the 3D Sonar View To change the 3D Bottom Style setting 1 2 Highlight 3D Bottom Style on the Sonar main menu Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 3D Bottom Style setting Grid Only Shaded with Grid Shaded Default Shaded with Grid eo a Frame Style 3 3D Frame Style Simple LS complex 3D Frame Style selects the frame style used in the 3D Sonar View To change the 3D Frame Style setting 1 Highlight 3D Frame Style on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 3D Frame Style setting Simple 2 3 4 Complex Default 3 aD Beam ay Beam Select 2D Beam Select EE 2D Beam Select sets which sonar returns from the transducer will be displayed on the screen When Beam Select is set to 455 kHz the returns from the 455 kHz
55. P or DOWN 4 WAY Cursor Control keys to select a View 3 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Status of the view from Hidden to Visible or vice versa Accessories Menu Tab From any view press the MENU key twice to access the tabbed Main Menu system then press the RIGHT cursor key until the Accessories tab is selected If no accessories are attached to the Accessory Bus no accessory menu choices will appear under the Accessories tab only the Screen Snapshot menu choice If an accessory is attached however additional menu choices that support the accessory will be added automatically See the Operations Manual that comes with your accessory for detailed information Gayl X XS ka T Accessories WeatherSense SmartCast WSL Accessories Menu no accessories attached Screen Snapshot Accessories Menu with accessories attached NOTE Accessories to enable WeatherSense and the SmartCast Wireless Sonar Link WSL require separate purchases You can visit our website at www humminbird com or contact our Customer Resource Center at 1 800 633 1468 for additional details 112 Snapshot Using Screen Snapshot 0 Screen Snapshot activates the screen snapshot function When Screen Snapshot is enabled pressing the MARK key creates a saved screen capture on the optional purchase MMC SD card installed in your unit s card slot All menus dialog boxes warnings and messages are captu
56. R STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state Humminbird Service Policy Even though you ll probably never need to take advantage of our incredible service policy it s good to know that we back our products this confidently We do it because you deserve the best We will make every effort to repair your unit within three business days from the receipt of your unit at our factory This does not include shipping time to and from our factory Units received on Friday are typically shipped by the following Wednesday units received Monday are typically shipped by Thursday etc All repair work is performed by factory trained technicians to meet exacting factory specifications Factory serviced units go through the same rigorous testing and quality control inspections as new production units After the original warranty period a standard flat rate service charge will be assessed for each repair physical damage and missing parts are not included Any repairs made after the original warranty will be warranted for an addi
57. RIGHT 4 WAY Cursor Control keys to change the Spot Soundings setting Hidden Visible Default Hidden 96 Navaids on Bird s Eye View Navaids on Bird s Eye View d Hidden gt Navaids on Bird s Eye View allows you to display or hide additional navigational aids such as lights and buoys in Bird s Eye View NOTE You will see more navigational aids with and optional purchase MMC SD card To change the Navaids on Bird s Eye View setting 1 Highlight Navaids on Bird s Eye View on the Chart main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Navaids on Bird s Eye View setting Hidden Visible Default Visible a m Depth 16ft Shaded Depth off fa 00 Shaded Depth allows you to change the depth used for shading on the chart views To change the Shaded Depth setting 1 Highlight Shaded Depth on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the shaded Depth setting Off 1 to 60 Feet or 1 to 20 Meters International Units only Default 15 ft 5 m Set Simulation Position Set Simulation Position b Advanced Set Simulation Position allows you to set the position of the boat used in the Simulator To set the Simulation Position 1 Activate the cursor and move it to the coordinates from where you want simulation to start NOTE The cursor must be active in order for this procedure to work 2 Make sure you are in Advanced User Mode then
58. View on the Sonar Main Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Bottom View setting Structure ID WhiteLine Default Structure ID Zoom Width 4 Narrow p Zoom Width allows you to control the width of the Zoomed Sonar the left hand side of the screen Zoom Width 2D Zoom View only To change the Zoom Width 1 Highlight Zoom Width on the Sonar Main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the width of the Zoomed Sonar Narrow Medium Wide Default Narrow 83kHz Sensitivity 0 83 kHz Sensitivity 10 10 Advanced 83 kHz Sensitivity changes the sensitivity of the 83 kHz beam Increasing the 83 kHz Sensitivity will display additional weak returns and decreasing the 83 kHz Sensitivity will display fewer weak returns The 83 kHz Sensitivity menu choice is only available when User Mode is set to Advanced see Setup Menu Tab User Mode To set the 83 kHz Sensitivity 1 Make sure you are in Advanced User Mode then highlight 83 kHz sensitivity on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to set the 83 kHz sensitivity 10 to 10 Default 0 80 Depth Lines Depth Lines d On b Advanced Depth Lines divide the display into four equal sections that are separated by three horizontal depth lines The depth of each line is displayed along the depth scale You can either turn Depth Lines On or Off The Depth Lines menu choice is ava
59. ailable when a Combo View is active To Adjust Split Screen Position 1 Highlight Split Position on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to change the size of the left side of a split screen Left 30 40 50 60 70 Right Default varies 72 Waypoint Name Only with an active cursor on a waypoint Waypoint 881 gt Waypoint Name allows you to view the Waypoints submenu for the waypoint under your cursor To view the Waypoint Name Submenu 1 Move the cursor onto an existing waypoint and press the MENU key once or use Cursor to Waypoint to select a waypoint from a list of saved waypoints 2 Highlight Waypoint Name on the Navigation X Press menu 3 Use the RIGHT 4 Way Cursor Control key to view the Waypoints submenu which contains the following menu choices panne Waypoint Submenu The Waypoint Submenu contains the following menu choices Edit allows you to edit the Name Position Latitude and Longitude and select the Icon that will be used to represent the waypoint in the Chart and Combo Views Delete allows you to delete a waypoint from the list of saved waypoints Target allows you to apply a target to a waypoint selected from the list of waypoints Grid allows you to apply a trolling grid to a waypoint selected from the list of waypoints 4 Cursor To Waypoint Cursor to Waypoint b Chart or Combo view only Cursor to Waypoint allows you
60. and Recording View 2 41 54 PM N 31 50 904 11 21 06 W 085 09 206 Current Ping Average Ping Remaining 33 mS 245 mS 4 0 1 0 3MB 7 R0000 1 S0N Recording icon Amount of recording left to play Snapshot thumbnail Recording mode icons Unavailable icon Amount of recording that has been played Q O nformation box Amount of space used for this recording NOTE For snapshots and recordings the indicator bar has several states during recording the amount of space remaining on the MMC SD card is indicated on the status bar During playback the amount of time memory remaining to play is indicated on the status bar When a snapshot thumbnail is highlighted the amount of room remaining on the MMC SD card is indicated Screen Snapshot When Screen Snapshot is enabled from the Accessories menu tab pressing the MARK key creates a saved screen capture when you have an optional purchase MMC SD card installed Once you have created a screen capture a screen capture thumbnail is added to the Snapshot and Recording View and is available to view at a later date See the full sized image by highlighting a thumbnail using the Up or Down 4 Way Cursor keys then using the Right 4 Way Cursor key to view the full image A border around the full size screen snapshot indicates that it is just a screen snapshot not a live view You can delete the selected image or all images by selecting a thumbnail and using Delete Image or usi
61. and the Snapshot and Recording View will display the playback Status You can change the speed skip to the beginning or end of playback and even reverse playback using the Playback Speed X Press menu item and stop the playback using the Stop Playback X Press menu Item these items are added to the X Press menus in all views during playback In the Snapshot and Recording View only playback speed can also be changed using the Left and Right 4 Way Cursor keys Playback is paused when the sonar Cursor is active and resumes playing when the cursor is removed Playback is automatically paused when the end of the recording is reached NOTE Sonar chart speed is increased during Fast Forward and reversed during Rewind This may reduce the quality of the sonar image since at higher speeds not every sonar return can be processed and displayed NOTE Navigation is not affected by the Sonar Recording feature but any active navigation is cancelled when playback begins or ends 43 Recording Playback 4 58 26 PM 7A R00099 SON 12 01 06 Current Ping 54 mS N 31 50 479 W 085 09 018 Remaining 6 11 Average Ping Average ping rate O Amount of time remaining to play Q Playback speed icons Amount of time remaining to play 9 Overall length of recording Q Amount of time already played Name of recording ine and Date recording started Position when recording started Current playback ping rate
62. anen 2o How GPS and Cartography Work uo ccecccscssessessssesesssessessssesssteseeseeeetaeen J Finish Routing the Cable and Check GPS Receiver Operation 0 24 Multi Media Card MMUC SD Slot cc ccccccesescssessesesessesessessesesmenensen 4 Temperature Probe Accessory Installation c c cccceccscscestsccsesssseetsseetescateseees 25 Sotware UE el 8S searty cenrissnarencth oan cen cae ne nairean iE EEEa EE 4 Testing the System Installation 26 EEEE S ON ID EE E AN N AET EEE T 4 Getting Started Using Your 900 Series 27 Installation Overview 3 Powering Up the Control Head oo ccccccssessestesseseeseeseesestestesseseeseeseateatesees 2 Control Head Installation 6 What s on the 3D Sonar Display oo cesccsscsscssseesssesssessesessseesssessseeseeeen 28 Gimbal MOUNTING tie Control FCAG cesics sesesizcevsceixacessizussscaseemndeleaivigevesvesaveeys 6 Whats onthe 20 SOM aP DEOR ectzceccseccen ceiversess E 29 Connecting the Control Head Power Cable to the Boat oo cece 11 Real ime sonar RTS VVINGOW occ sxsccerszceeicsseacucesacevinevcessdetacosiertvenveareeciesee 30 Transducer Installation 12 aneo a Fear AUG E O E 30 Iransom Iransducer INGSTANATIOM ssisiriuirsisrsrissnsrsnissssiateeresassrisissiianiniain 12 Key Functions 31 Inside the Hull Transducer Installation cccsccssssescesesceseseeesesteseeteeeeeees 17 PERAI E E G a E E EE 31 Trolling Motor Transducer Installation c cccccccesceesceseeesteseesesceeateseeseanen 20 RA
63. ard Humminbird GPS Receiver With WAAS signal GPS accuracy is improved to within 3 meters 95 of the time Outside the United States regional governmental coalitions have created similar systems such as EGNOS Europe and MSAS Japan Glossary GPS amp Navigation Terms Waypoint A Waypoint is the saved location latitude longitude of a point of interest that is stored in a GPS receiver s memory This can include a marker buoy dock fishing hole or anywhere else the user may want to return to Humminbird products offer the ability to name and assign a symbol to the saved location Depth Date and Time of Day when the waypoint was created Is also saved Waypoint Target Waypoint Target is a Humminbird feature that displays a precise bull s eye around a selected waypoint This bull s eye is used to easily monitor boat position relative to a waypoint and is useful for fishing over submerged structure With Waypoint Targets a quick look at the screen lets you know how far off the waypoint the boat has drifted 132 Appendix A Transducer Mounting Template SHS 7W Remove and use for Transducer Installation Use 3 2 drill bit DO NOT LET DEADRISE INTERSECT THIS LINE PLACE EITHER CORNER aa ON DEADRISE ANGLE Ne Notes 133 Notes 134 Contact the Humminbird Customer Resource Center in any of the following ways By Telephone Monday Friday 8 00 a m to 4 30 p m Central Standard Time 1 800
64. as the current route this menu setting also begins navigation on this route Routes can be traveled in either the forward or reverse direction Info displays information about the route including the distance and bearing from each waypoint to the next Oe WMI er Garay ser yor wwe es Chart Orientation allows you to select whether the views containing charts should be drawn North Up or Course Up To change the Chart Orientation setting 1 Highlight Chart Orientation on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Chart Orientation setting North Up Course Up Default North Up NOTE The Chart Orientation setting does not apply to the Bird s Eye View 91 me Reference North Reference l North Reference allows you to have bearings displayed with one of two orientations True North or Magnetic North To change the North Reference setting 1 Highlight North Reference on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the North Reference setting True Magnetic Default True Trolling Grid Rotation 0 Trolling Grid Rotation of 9 Trolling Grid Rotation allows you to set the orientation of the trolling grid in degrees where a setting of 0 displays a standard North South East West alignment See Waypoints for information on how to set a Grid To change the Trolling Grid Rotation setting 1 Highlight Trolling Grid Rotation on th
65. at a constant point on the display regardless of changes in depth This flattens out the bottom contour but is effective at showing fish on or near the bottom and is preferred by many saltwater anglers 128 GPS amp Navigation Terms Acquisition Time The length of time that a GPS receiver typically takes to determine a position from at least three satellites Humminbird GPS receivers provide very fast acquisition times under one minute permitting users to get out on the water faster Alarm Arrival The audible alert that sounds when the boat is equal to or less than the alarm setting 25 feet 3000 feet from the location of the destination waypoint Alarm Drift Drift Alarm is an audible alert that sounds when the boat is equal to or over the alarm setting 25 feet 3000 feet from the location where the alarm was turned on Alarm Off Course Off Course Alarm is an audible alert that sounds when the boat s distance from the intended Track Cross Track Error is equal to or over the alarm setting 25 feet 3000 feet See Track and Cross Track Error Altitude Altitude measures height above sea level Altitude is a measurement that can be provided by GPS Bearing BRG Bearing is the direction to a destination waypoint measured in degrees from North i e 321 where 000 is North 090 East 180 is South 2 0 is West Chartplotter Chartplotter describes a navigation device that shows Present Position
66. avigation capabilities with advanced fishfinding The following GPS functionality is currently supported by the 900 Series Fishing System when it is connected to the included GPS receiver e View current position e View current track breadcrumb trail e View precision speed and heading from your GPS receiver e Save tracks waypoints and routes e Travel a route and navigate from one waypoint to the next Your 900 Series supports Navionics Gold HotMaps and HotMaps Premium on MMC or SD card media NOTE Your 900 Series does not support Navionics Classic Charts only Navionics Gold HotMaps and HotMaps Premium Your unit also comes with a builtin UniMap with a more detailed map of North America Domestic models or a more detailed map of Europe and southeast Asia including Australia and New Zealand International models Your 900 Series uses the GPS Receiver to determine the position of the boat automatically and uses the zoom level settings on a particular view to select the best chart to display See Viewing Cartography for more information Multi Media Card MMC SD Slot Your 900 Series Fishing System also has a multi media card MMC SD slot that is used to insert optional purchase cards containing additional detailed maps If you insert an MMC SD that contains a more detailed chart for a particular location your 900 Series Fishing System will retrieve that chart and display it automat
67. be overcome by proper transducer installation Many Humminbird products have a Noise Filter menu setting that allows the user to clear the screen of noise that is difficult to eliminate Pixels Pixels are the picture elements or small square blocks that make up the image on the LCD Measured as a vertical by horizontal number i e 640 V x 320 H this key specification typically indicates the quality of resolution 124 Sonar Terms In fishfinders the total resolution vertical multiplied by horizontal is often less important than the Vertical Pixel resolution See Pixels Vertical Pixels Vertical Vertical Pixels are a number of vertical picture elements in a single column on an LCD display A greater number of vertical pixels provide finer resolution of targets detected by sonar Essentially a vertical distance the depth when divided by a larger number breaks that distance into smaller samples each representing a smaller area and thus providing more detail In fishfinders vertical pixels are more critical than horizontal pixels because the horizontal axis of the display represents time or history Sonar information on the horizontal axis can vary greatly depending on boat speed and the Chart Speed setting A greater number of horizontal pixels show more sonar history that the boat has passed through On many models Humminbird provides the most vertical pixels to provide a better display resolution See Chart Speed and Pi
68. bottom The Zoom Preview Box shows where the zoomed view is in relation to the full range view The Zoom Level or magnification is displayed in the upper left corner and can be changed to Suit conditions Upper and Lower Zoom Depth Range numbers indicate the depth of the water which is being viewed Freeze Frame Pressing any arrow on the 4 WAY Cursor Control key will freeze the screen in the 2D Sonar Zoom View and a cursor and cursor dialog box will be displayed on the screen The cursor can be positioned on the display using the 4 WAY Cursor Control key to determine the depth of any sonar return In addition see the effects of menu setting changes with Instant Image Update Pressing EXIT will exit Freeze Frame and the display will start to scroll 38 2D Zoom View F Depth Upper Depth Range Full Range View Q O Iriplog Upper Depth Range Zoom View O emnperature Zoom Preview Box Q Speed Full Range View Q Zoomed View Lower Depth Range Full Range View D O Zom Level Lower Depth Range Zoom View 6 Beam Sonar View 6 Beam Sonar View 6 Beam Sonar View displays information from each of the six 455 kHz beams in a traditional 2D representation This view displays the raw sonar returns from each of the beams that are used to create the 3 dimensional wire frame representation of the bottom in the 3D Sonar View The 6 Beam sonar View can be used for identifying structure on the bottom and sonar returns in the water co
69. cing off the bottom once rebounding to the water surface and then traveling back down to the bottom to be reflected again Second returns are more common 125 Sonar Terms in shallow water and over hard bottoms it is actually possible to see a third sonar return under some circumstances The second return provides useful information to help determine bottom hardness as areas with harder bottoms will generally create a second return The second return can be used as a guide to set Sensitivity when in shallower water Sensitivity Sensitivity is a user feature that adjusts the sensitivity of the sonar system to show more or less detail in the water Higher sensitivities are often preferred however when the water contains debris silt storm debris etc and it can be difficult to pick out targets Conversely if sensitivity is set too low relevant targets may be missed SONAR SONAR is the acronym for SOund and NAvigation Ranging Sonar technology uses precision sound bursts transmitted underwater to determine the distance and other attributes of objects in the water Distance can be determined because the speed of sound in water is constant and the time for the signal to return is measured Sound also travels very quickly underwater making sonar a responsive cost effective tool Sonar is the basic technology behind all recreational and commercial fishfinding and depthfinding devices Sonar Echo Enhancement Sonar Echo Enhancement is a H
70. cording as well as how much space is remaining on the MMC SD card NOTE The waypoints that are created by a recording have the same name as the file and use a custom waypoint icon Recording filenames begin with the letter R For more information see Snapshot and Recording X Press Menu 42 Recording Slider Bar N 25 42 792 W 080 13 342 Current Ping 648 mS Recording Indicator Current Ping Rate 2 Amount of space and time used by this recording Average Ping Rate Q Name of recording Amount of space remaining on card O Time and Date recording was started Total amount of space on card amp Position where recording was started Highlighting a recording You can scroll through the whole list of recording icons available in the Snapshot and Recording View using the 4 WAY Cursor keys The highlighted icon will be surrounded by arrows and a green play triangle will appear to its right Playing back a recording Highlight a recording icon using the Up or Down 4 Way Cursor keys then use the Right 4 Way Cursor key to start playback During playback all active navigation is cancelled all other thumbnails and icons will disappear and a Playback message box similar to the Simulation message will be displayed periodically When playback begins the view is automatically switched to the primary Sonar View for your model and no live sonar data will be displayed only recorded sonar and GPS data will be shown
71. cscesescetescesesestesesteeseesteseeeees Add a Waypoint Target or Trolling Grid ceccccecesccecessesteseeseeseeseesesteseeees Save Edit or Delete a Route cceccccsscsscssssssssssssessesssscesesteseesssussesseseeseeesaes Save OF Clear a Current rACKk c ccssesccsessessesssessescssessssecsesssseessessesssassseeesaes Edit Delete or Hide Saved Tracks Man Overboard MOB Navigation The Menu System Start Up Options Menu VITO a A OND eae E EE AAAA NRA AEE IMMUN ALO ar E E E EAE EARR System Status T EAE E I S ACCESSO TOS loriara TE GPS Diagnostic View Table of Contents 2D Sonar X Press Menu 63 Navigation X Press Menu 71 PETS SVC eta ct bavi EEEE E E 63 PCS cae spe aates EE EE E eae 72 SNE OI sect E en N NEE E toaioistceonmnaiinn 64 EPOSO eE EEEE 72 Sensitivity sees Sieh eee bce sabes ects auld E E E E E EE 64 Waypoint Name only with an active cursor ON a waypoint oseesecsceteseseseseeeees 71 Upper Range Cursor to Waypoint Chart or Combo view only o s 73 Advanced 2D Sonar or 3D 2D Combo View when 2D Sonar side is active only 65 i 5 DAVE GUITOMT PACK asasinen a 73 ical ci ai i ie a Ela UWL CIE ICING exscetcascinence iene aetaacccaeasenes eanec cPecnesseattes terse castauicioneanedance ie Chart Speed oo cceeccccecccscsscsssscssssesssesssesssessesesessssesissesissesissesessseestsesneeteneeness 66 O Save Current Route only when navigating essees 74 Bottom LOCK 2D Zoom View only ceccecceccssesssese
72. cure the 900 Series control head to the mount Repeat step 2 for the other side You can now place the control head in various locations to decide which is best for mounting Rotating the mounting bracket to the top of the control head will allow for overhead mounting The chosen mounting area should allow for sufficient room so the control head can pivot through the full tilt range and allow for easy removal and installation NOTE You can drill the cable pass hole underneath the gimbal bracket allowing you to thread the cables through the knock out holes in the mount however if you cannot drill the hole directly under the mounting bracket then you will need to drill the cable pass hole behind the bracket and will need to mount the hole cover there instead NOTE When drilling holes in fiberglass hulls it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating Fill all holes with marine grade silicone sealant NOTE You must have underside access to the mounting location to pass the cables through to the surface Also make sure that the mounting surface Is adequately supported to protect the control head from excessive wave shock and Vibration and provide visibility while in operation 3 After the mounting location has been determined loosen the gimbal knobs and remove the control head from the gimbal bracket NOTE Alternate hole patterns are ava
73. d This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode To change the Aux Temp Offset setting 1 Make sure you are in Advanced User Mode then highlight Aux Temp Offset on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Aux Temp Offset setting 10 0 to 10 0 degrees Default 0 Temp Offset 0 0 Temp Offset 10 0 io Advanced Temp Offset will adjust the temperature readout by the amount entered This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode To change the Temp Offset setting 1 Make sure you are in Advanced User Mode then highlight Temp Offset on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Temp Offset setting 10 0 to 10 0 degrees Default 0 0 or Off Speed Calibration Advanced with Speed paddlewheel only Speed Calibration 0 eU __ 20 Speed Calibration will adjust the speed readout by the percentage entered and will appear in the menu if a Speed accessory is connected and the paddlewheel has moved at least once when the unit is in Advanced User Mode see Setup Menu Tab User Made To change the Speed Calibration setting 1 Make sure you are in Advanced User Mode then highlight Speed Calibration on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Speed Calibration setting 20 to 20 Default
74. d Pings Per Second Use the 4 WAY Cursor keys from the Snapshot and Recording View to start playback of a specific recording icon You can then cycle through all the views using the VIEW key to see what those views looked like during the recorded time period You can also use the X Press menu to change playback speed stop playback and delete recording icons Working with sonar recordings is a six step process 1 Displaying the Snapshot and Recording View 2 Starting a sonar recording using the Snapshot and Recording X Press menu 3 Changing the maximum ping rate for the recording using the Snapshot and Recording X Press menu optional 4 Stopping a recording using the Snapshot and Recording X Press menu 5 Playing back a recording using the Snapshot and Recording View and the 4 Way Cursor keys and changing the playback speed using the Snapshot and Recording X Press menu 6 Deleting a recording using the Snapshot and Recording X Press menu For more information see Snapshot and Recording X Press Menu When you start a sonar recording you will see a message that a waypoint has been created at your current location During recording playing back a recording and screen snapshot viewing are not allowed An information box displays a variety of information including the numbered file name assigned to the SON file that is being created The slider bar at the bottom of the screen shows the progress of the re
75. ddition to the parts supplied you will need a hand drill with various bits a socket wrench 5 16 a Phillips head screwdriver and marine grade silicone sealant NOTE When drilling holes in fiberglass hulls it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating Fill all holes with marine grade silicone sealant WARNING Do not touch an active transducer during operation as this may cause physical discomfort and may result in personal injury in the form of tissue damage Handle the transducer only when the power to the control head is off Transom Transducer Installation If you will be installing a transom mounted transducer use the procedures in this section There are several procedures you will have to perform in order to install a transom mounted transducer They are Pivets Strakes Determine transducer mounting location Mount the bracket to the boat Attach the pivot to the transducer Mount the transducer pivot assembly to the bracket Adjust the running position of the transducer Route the transducer cable Perform a final test of the transom transducer installation Stepped Hull O Deadrise Angle Determine transducer mounting location NOTE If transom mounting is not possible because of a stepped hull or cavitation noise and you have a single layer fiberglass hull In hull installation is an option See Inside the Hull Trans
76. der for the control head to find the bottom To change the Noise Filter setting 1 Make sure you are in Advanced User Mode then highlight Noise Filter on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Noise Filter setting Off Low Medium High 1 High 2 High 3 Default Low Max Depth Auto Max Depth Water Type Water Type Autol 1000 Advanced 4 fresh Advanced Max Depth adjusts the maximum depth of 2D operation The performance Water Type configures your unit for operation in fresh or salt water The of your 900 Series can be tuned to the maximum depth you will be fishing Water Type menu choice is available when User Mode is set to Advanced in by setting the Max Depth When a maximum depth is set your see Setup Menu Tab User Made 900 Series will not attempt to acquire sonar data below that depth thus increasing overall performance When Max Depth is set to Auto the 900 Series will acquire bottom readings as needed within the capacity of NOTE In salt water what would be considered a large fish might be 2 to 10 times bigger than a large fish in fresh water depending on the type of fish you are seeking The salt water setting allows for a greater range in fish size the unit If the bottom i deeper than the Max pepe seni the digital adjustment to account for this Also make sure that the Water lype is set depth readout will tlash indicating that the J00 Series cannot
77. ducer Installation for more information 1 First determine the best location on the transom to install the transducer Consider the following to find the best location It is very important to locate the transducer in an area which is relatively free of turbulent water As a boat moves through the water turbulence is generated by the weight of the boat and the thrust of the propeller s either clockwise or counter clockwise This turbulent water is normally confined to areas immediately aft of ribs strakes or rows of rivets on the bottom of the boat and in the immediate area of the propeller s Clockwise propellers create more turbulence on the port side On outboard or inboard outboard boats it is best to locate the transducer at least 15 380 mm to the side of the propeller s The best way to locate turbulence free water is to view the transom while the boat is moving This method is recommended if maximum high speed operation is a high priority If this is not possible select a location on the transom where the hull forward of this location is smooth flat and free of protrusions or ribs The hydrodynamic shape of your transducer allows it to point straight down without deadrise adjustment On boats with stepped hulls it may be possible to mount the transducer on the step Do not mount the transducer on the transom behind a step to avoid popping the transducer out of the water at higher speeds the transducer must remain i
78. e coordinates to any valid position The Icon used to represent the waypoint in the Chart and Combo Views can also be changed Edit allows you to choose from a list of previously saved waypoints then edit the Name Position Latitude and Longitude and select the Icon that will be used to represent the waypoint in the Chart and Combo Views 90 Delete allows you to delete a waypoint from the list of saved waypoints Cursor To allows you to move the cursor quickly to a waypoint selected from the list of saved waypoints Go To allows you to select a waypoint and start navigation toward that waypoint or add that waypoint to the end of the current route Target allows you to apply a target to a waypoint selected from the list of waypoints Grid allows you to apply a trolling grid to a waypoint selected from the list of waypoints nan er Routes allows you to view the Routes submenu To view the Routes Submenu 1 Highlight Routes on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control keys to view the Routes submenu Pontes Routes Submenu The Routes Submenu contains the following menu choices Create allows you to create a new empty route and add waypoints to it immediately Edit allows you to select a previously saved route and edit its name and the waypoints on It Delete allows you to delete a route from a list of previously saved routes Travel allows you to select a previously saved route to use
79. e Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Trolling Grid Rotation setting 0 to 89 Default 0 Trackpoint Interval Trackpoint Interval Track Min Distance 16ft Track Min Distance q 15 seconds gt 3300 Advanced Trackpoint Interval allows you to select the time period between trackpoints The current track can only contain up to Track Min Distance allows you to set a minimum distance of travel before a 20 000 trackpoints so longer time periods cause the track to extend back trackpoint is added to the track further in time but will be less detailed NOTE Track Min Distance works in conjunction with Trackpoint Interval Both NOTE Trackpoint Interval works in conjunction with Track Min Distance Both conditions must be met before a trackpoint is added to the current track conditions must be met before a trackpoint is added to the current track To change the Track Minimum Distance setting Jo change the Trackpoint Interval setting 1 Make sure you are in Advanced User Mode then highlight Track 1 Highlight Trackpoint Interval on the Navigation main menu Min Distance on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Trackpoint Interval setting 1 second 5 seconds 10 seconds 15 Track Min Distance setting 1 to 300 feet or 1 to 100 meters seconds 30 seconds or 60 seconds
80. e port side of the boat while right facing fish indicate fish off the starboard side Each fish icon is available in three different sizes Larger fish icons are used to represent Barometric Pressure Requires optional purchase WeatherSense Q Temperature water surface temperature Speed The 900 Series can display the speed of the boat and can keep a triplog of nautical or statute miles traveled with Speed input or GPS Receiver stronger returns The icons used in the 2D Sonar View are identical to the icons used in the 3D Sonar View 28 What s On the 2D Sonar Display The 900 Series can display a variety of useful 2D information about the area under and adjacent to your boat including the following items Triplog lt gt lt gt Depth water depth can be set to alarm when the water becomes too shallow Timer Elapsed time with Speed accessory or GPS Receiver Distance Distance traveled with Speed accessory or GPS Receiver Average Speed Average speed reading with Speed accessory or GPS Receiver a Taaa aaa l a JETA 10 Barometric Pressure Requires optional purchase WeatherSense Q Temperature water surface temperature Speed if a Speed accessory or GPS Receiver is attached the 900 Series can display the speed of the boat and can keep a triplog of nautical or statute miles traveled 29 Thermoclines layers of water with different temperatures that appear a
81. e system to your fishing requirements see View Menu Tab The VIEW key is used to cycle through all available views MENU Key The MENU key is used to access the menu system Start Up Options Menu Press the MENU key during the power up sequence to view the Start Up Options menu X Press Menu Press the MENU key once for the X Press Menu The X Press Menu allows you to access frequently used settings without having to navigate through the whole menu system When the X Press Menu is displayed you can use the UP or DOWN Cursor keys to move to a particular menu choice As soon as you alter a parameter using the RIGHT or LEFT Cursor keys the X Press Menu will collapse temporarily and the screen will update if it is affected by your menu setting change allowing you to see the effects of your action immediately Reactivate the X Press Menu by using the UP or DOWN Cursor keys Main Menu Press the MENU key twice for the tabbed Main Menu System The Main Menu System is organized under tabbed headings to help you find a specific menu item quickly Alarms Sonar Navigation Chart Setup Views and Accessories tabs are part of your tabbed Main Menu System Use the LEFT or RIGHT 4 WAY Cursor Control key to select a tab then use the DOWN or UP key to select the menu item and the LEFT or RIGHT key to alter a menu setting 4 WAY Cursor Control Key The 4 WAY Cursor Control Key has multiple functions depe
82. e temperature probe accessory a temperature sensitive probe in a A high impact plastic housing The A module is intended for installation on the transom and will work well on almost any boat In addition to the parts supplied you Escutcheon Plate Cable Clamps Sensor Clamp O Temp Sensor 25 The Temperature Probe incorporates 1 KO will need a hand drill with various 2 bits marine grade silicone sealant and a Phillips head screwdriver 3 4 Locate an area on the transom of your boat that will be 6 to 8 or farther from the transducer s This area must also maintain contact with the water even at high speeds Do not mount the sensor directly in front of the propeller or outdrive and make sure that there are no protrusions such as ribs rows of rivets or transducers directly forward of the mounting location as these may affect the flow of water over the temperature probe Align the sensor in the clamp and align it on the transom so that the lower edge is flush with the hull of the boat and mark the hole location On fiberglass hulls it is best to start with a smaller drill bit and use progressively larger bits to reduce the chance of chipping or flaking the outer coating Drill a 1 8 3 mm mounting hole approximately 3 4 19 mm deep Seal the mounting holes with marine grade silicone sealant and attach the sensor to the transom using the screw provided Hand tighten only Routing the
83. e the Right 4 Way Cursor key to view the full image A border around the full size screen capture indicates that it is just a screen capture not a live view You can delete the highlighted image or all captured images using the Snapshot and Recording X Press menu See Snapshot and Recording X Press menu Delete Image and Delete All Images for more information NOTE When you highlight a snapshot thumbnail the amount of room remaining on the SD card will be displayed NOTE The waypoints that are created by a snapshot have the same name as the file and use a custom waypoint icon Snapshot filenames begin with the letter S NOTE You may view data files associated with each screen snapshot by removing the MMC SD card from your unit and installing it in your optional purchase MMC SD card reader connected to a PC Use Windows Explorer to see the contents of your MMC SD card you will notice that a DAT may show up as X1 file is created for every BMP screen capture this data file includes the thumbnail view and is required in order to be able to view the screen snapshot from your unit so don t delete these files Troubleshooting Before contacting the Humminbird Customer Resource Center please read the following section Taking the time to review these troubleshooting guidelines may allow you to solve a performance problem yourself and therefore avoid sending your unit back for repair 900 Series Doesn t Power
84. e the potential for interference with other marine electronics a separate power source such as a second battery may be necessary You are now ready to install the transducer Find the section that refers to your specific transducer installation method NOTE Make sure that the power cable is disconnected from the control head at the beginning of this procedure NOTE Humminbird is not responsible for over voltage or over current failures he control head must have adequate protection through the proper selection and installation of a 3 Amp fuse Transducer Installation There are three different installation methods for your transducer e Transom Transducer e Inside the Hull Transducer e Trolling Motor Transducer Find the section that describes the method of installation you will be using NOTE If the included transducer will not work for your application you may exchange it NEW and UNASSEMBLED with mounting hardware included for a transducer appropriate for your application often at very little or no charge depending on the transducer Call the Humminbird Customer Resource Center 1 800 633 1468 for details and pricing or visit www humminbird com Product Support Transducer Exchange tor more information NOTE Due to the wide variety of hulls only general instructions are presented in this installation guide Each boat hull represents a unique set of requirements that should be evaluated prior to installation In a
85. ed on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Units Speed setting kph International models only mph kts Default kph for International models and mph for Domestic models 104 m oe i Aatvanced i User Mode sets the menu system to either Normal or Advanced When set to Normal only the basic menu options are shown When set to Advanced default setting additional menu choices are available To change the User Mode setting 1 Highlight User Mode on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the User Mode setting Normal Advanced Default Advanced Language Language 4 English b International only Language selects the display language for menus nternational models only To change the Language setting 1 Highlight Language on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Language setting Default English Triplog Reset Triplog Reset b with Speed input only Triplog Reset resets the Triplog to zero The Triplog provides the following information timer for elapsed time distance traveled since last reset and average speed To Reset Triplog 1 Highlight Reset Triplog on the Setup menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate Triplog Reset 3 The Confirm dialog box will appear To reset the Triplog press the RIGHT Cursor key once more To cancel Reset Triplog press the LE
86. ensitivity at Medium Sensitivity at High To adjust the Sensitivity 1 Highlight Sensitivity on the 2D sonar X Press menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to increase or decrease the Sensitivity setting Low 1 High 20 Default 10 Upper Range oft Upper Range ol 990 2D Sonar or 3D 2D Combo View when 2D Sonar side is active only Upper Range sets the shallowest depth range that will be displayed on the 2D Sonar View or 3D 2D Combo View when the 2D Sonar side is active The Upper Range menu choice is available when User Mode is set to Advanced see Setup Menu Tab User Mode and can only be accessed from the 2D sonar View or 3D 2D Combo View when the 2D Sonar side is active Upper Range is often used with Lower Range For example if you are only interested in the area between 20 and 50 feet deep you should set the Upper Depth Range to 20 and the Lower Depth Range to 50 The Sonar View will then show the 30 foot area between 20 and 50 and will not show the surface or the bottom assuming the bottom is deeper than 50 feet and will show greater detail for that area between 20 and 50 feet NOTE A minimum distance of 10 feet will be maintained between the Upper and Lower Range regardless of the manual settings entered To adjust the Upper Range 1 Make sure you are in Advanced Mode then highlight Upper Range on the 2D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cu
87. epth of the down riggers Speed Over Ground is optimal for navigation as accurate destination times can be derived from this measurement Humminbird products allow for input and display of both sources Structure Structure is a general term for objects on the bottom that present a discontinuity and are a likely attractor for fish This includes bottom contour features drop offs humps and holes standing structure stumps timbers brush piles and a wide range of other potential objects sunken boats reefs Humminbird units excel at showing structure with great detail over a wider area due to unique sonar configurations developed for the angler Structure ID Structure ID is a Humminbird feature that describes the traditional grayscale method of presenting sonar information See Grayscale Surface Clutter Surface Clutter is a phenomenon where sonar returns are reflected off of tiny objects near the surface of the water including algae and even 126 Sonar Terms air bubbles Typically saltwater environments have significantly greater surface clutter than freshwater due to continuous wind and wave action that causes aeration at the surface The Surface Clutter menu provides manual control to bias the default settings under extreme conditions Target Separation Target Separation is the measurement of minimum distance that a fishfinder needs to be able to recognize two very close objects as two distinct targets i e two fis
88. er and the hull is faulty not airtight or because the transducer is dirty Check with your Installation Guide for guidance on re positioning the transducer and make sure the transducer is clean Low battery voltage may be affecting the power of signal transmission Electrical noise from the boats engine may be interfering with sonar reception See Finding the Cause of Noise for more information 115 Finding the Cause of Noise Electrical noise usually affects the display with many black dots at high speeds and high sensitivity readings One or more of the following sources can cause noise or interference Possible Source of Noise Isolation Other electronic devices Turn off any nearby electronic devices to see if the problem goes away then turn them on one at a time to see if the noise re appears The boat s engine To determine whether the boat s engine is the source of the noise increase the RPMs while the boat is in neutral and stationary to see if the noise increases proportionately if noise appears when you rev the engine the problem could be the spark plugs alternator or tachometer wiring Replace the spark plugs with resistor plugs install an alternator filter or route the control head power and transducer cables away from the engine wiring Cavitation from the boat s propeller Turbulence created by the propeller can cause noise make sure the transducer is mounted at least 15 38 cm from the propeller and that the wat
89. er flows smoothly over the face of the transducer at all times 116 1 Year Limited Warranty We warrant the original retail purchaser that products made by Humminbird have been manufactured free from defects in materials and workmanship This warranty is effective for one year from the date of original retail purchase Humminbird products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird s option and returned to the customer freight prepaid Humminbird s sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird Humminbird is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts This warranty does not apply to a product that has been e mproperly installed e Used in an installation other than that recommended in the product installation and operation instructions e Damaged or has failed because of an accident or abnormal operation e Repaired or modified by entities other than Humminbird Please retain your original receipt as a proof of the purchase date This will be required for in warranty service 117 THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDE
90. ese accessories online or contact our Customer Resource Center at 1 800 633 1468 900 Series Introduction Real Time Sonar Your 900 Series Ultra Wide Screen Fishing System comes in the following configuration e Humminbird 967c 3D Combo Ultra Wide Screen Fishing System with Chartplotter Maps and Dual Frequency 455 kHz and 83 kHz Transducer GPS Receiver included How the 900 Series Works Sonar technology is based on sound waves The 900 Series Fishing System uses sonar to locate and define structure bottom contour and composition as well as depth directly below the transducer Your 900 Series Fishing System sends a sound wave signal and determines distance by measuring the time between the transmission of the sound wave and when the sound wave is reflected off of an object it then uses the reflected signal to interpret location size and composition of an object Sonar is very fast A sound wave can travel from the surface to a depth of 240 ft 70 m and back again in less than 1 4 of a second It is unlikely that your boat can outrun this sonar signal Older Pings Scroll Across Display SONAR is an acronym for SOund and NAvigation Ranging Sonar utilizes precision sound pulses or pings which are emitted into the water in a teardrop shaped beam The sound pulses echo back from objects in the water such as the bottom fish and other submerged objects The returned echoes are displayed on t
91. eseesestestesseseesessstesteseeseeesnsseesen 66 a eee a 4 CA E EAEE Bottom Range 2D View only when Bottom LOCK is ON sesstsscescsstestesteeteeceeeesee 66 vee ca ene ce ng 2D 3D POTY as 67 ROTC DEANNA E season estar carina G Cancel Navigation only when navigating cccccccssescestsseesesceesssessessseeeneeees 6 Cancel MOB Navigation fanly when MOB Navigation is activated esos is Remove Target only ifa Target is active c e 10 3D Sonar X Press Menu 3D Sonar Views only 68 O TO o Remove Grid only ifa Grid is active asese 15 PO GS E tener tes ttn vases E E 68 EN ee 5 n created WAYPOINT oeseeseescessess eset PUPS MUN execpt fest E OIE 68 BEIT SAU OS E A Aime aay 6 Beam Sensitivity 6 Beam Sonar View only ce 69 Snapshot and Recording X Press Menu SOPOT COW Ml E E E EE EE 69 Snapshot and Recording View only 16 3D Lower RANGE a ccxscxveesncodia evzrecatecnsiontescd etocdbact taconanaadionisesdreesspdiaatvaeioceiarsten 69 start Recording Dda e E E nassesucesvam aan meenuomiammeyiesss 70 fp ne itn AEE SAE IN EOE A top Recording Reset e E E E E E E yeneenaoneganeicas 70 E E E Card OW ecccccvccocssoccsocosoosocoisecnee 77 PVP SIO HOMEY ar e E A EA ARE 70 Ea Delete Image Cancel Navigation only when navigating escccccscscceeseescsecsesecsetectecseesssecseteeseeaes 71 optional purchase MMC SD Card Snapshot and Recording View Only 77 Table of Contents Delete All Images optional purchase MMC SD Card Snaps
92. ew e Accessory Test View 3D 2D Combo View is the default view When the VIEW key is pressed the display cycles through the available views When the EXIT key is pressed the display cycles through the available views in reverse order Any view can be hidden or displayed as part of the view rotation using the Views Menu tab NOTE When you change any menu settings that affect the sonar the view will update immediately i e you don t have to exit the menu to apply the change to the screen Views and Readouts All views have an Information Bar on the left side of the screen consisting of readouts that are stacked vertically and that change from view to view You can customize the information displayed in individual readouts on many views Including suppressing a particular readout so that nothing is displayed the ability to customize readouts depends on the view and whether you are navigating see Setup Menu Tab Select Readouts tor V more information 39 3D 2D Combo View 3D 2D Combo View displays a 3 dimensional representation of the bottom next to the traditional 2 dimensional sonar representation The 3D 2D Sonar Combo View is especially useful for evaluating the bottom terrain from the 3D window while simultaneously viewing the 2D window for structure and bottom hardness A green arrow points to the side that is active see Sonar X Press Menu Active Side for more information You can also adjust the size of the left side
93. f that perimeter the Drift Alarm will sound To change the Alarm Tone setting 1 Highlight Alarm Tone on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Alarm Tone setting High Medium Low Default Medium s00075 Drift Alarm Circle To change the Drift Alarm setting 1 Highlight Drift Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Drift Alarm setting Off 25 to 3000 feet 10 to 1000 meters International models only Default Off 102 a X 1X had S setup E Units Depth Feet gt Units Temp F Units Distance Statute Miles Units Speed mph User Mode Advanced English Triplog Reset Restore Defaults Select Readouts Depth Offset 0 0 Aux Temp Offset 0 Temp Offset 0 ft 0 0 ff Speed Calibration 0 Local Time Zone EST UTC 5 Daylight Saving Time Oo Position Format dd mm mmm 12 Hour mm dd Small tenths Off Setup Menu Setup Menu Tab From any view press the MENU key twice to access the tabbed Main Menu System then press the RIGHT cursor key until the Setup tab is selected NOTE Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode and what accessories are attached to the control head 103 Units Depth Units Depth cease Units Depth selects the units of measure
94. f the transducer that has the mounting ears to face towards the bow of the boat Permanently mount the transducer 7 Weight the transducer so that it will not move while the epoxy is oa curing 1 Make sure the position of the transducer is marked 9 2 You may have to disconnect the cable to the control head and IES EAEE EA EEE WATE EE EA S ER reconnect it at the end of this procedure 8 If you unplugged the transducer cable at the beginning of this 3 Remove the water from inside the hull and thoroughly dry the procedure plug it back into the control head mounting surface If the surface is excessively rough it may be NOTE Neither water spilled gasoline nor oil will affect the performance of the necessary to sand the area to create a smooth mounting surface transducer 4 Slowly and thoroughly mix an ample quantity of two part slow cure epoxy Avoid trapping air bubbles Trolling Motor Transducer Installation If you want to install the transducer on a trolling motor use this procedure Several styles of the transducer are compatible with trolling motor mounting If you have a trolling motor bracket lt 2 refer to the separate installation instructions that o gt are included with the bracket SS NOTE After trolling motor transducer installation please perform the final testing and then finalize the installation see Test and Finish the Transducer Installation Trolling Motor Transducer Options If you don t
95. from external sources Additionally the receiver offers a wide dynamic range which provides the ability to receive very strong signals alternating with very weak signals without the strong signal overwhelming the weak signal See ransducer and Noise TripLog TripLog is a Humminbird feature that provides an on screen counter for Elapsed Time Average Speed and Total Distance traveled and requires a speed input to activate the feature TripLog appears on the Big Digits View and can be reset to zero through the TripLog menu 127 GPS amp Navigation Terms TrueArch TrueArch is a Humminbird feature that provides true fish arches not artificial arches or symbols Humminbird units are capable of producing fish arches due to the wide 60 sonar beam of DualBeam PLUS an extremely sensitive sonar receiver see Fish Arch Viewing Angle Viewing Angle is an attribute of an LCD that characterizes visibility of the display when viewing from off the central access such as when standing to the side of the fishfinder Wider viewing angles are better because the information remains visible even when viewing from the side WhiteLine WhiteLine is a Humminbird feature that highlights the strongest sonar return on the display using a very light gray band This is preferred by some anglers who have grown accustomed to the feature on paper graph chart recorders WideSide WideSide is a Humminbird sonar configuration used in an
96. ft Bottom Range 10060 2D Zoom View only when Bottom Lock is On Bottom Range allows you to control how much of the water column measured up from the bottom is shown in the 2D Zoom View Choose a small value to see low lying bottom structure or details of the bottom return Choose a larger value to see large structure in deeper water It is possible to set the Bottom Range to be greater than the depth In this case you may see surface clutter in a wavy band that mirrors changes in the depth To adjust the Bottom Range 1 In the 2D Zoom View highlight Bottom Lock on the 2D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Bottom Lock setting to on Off On Default Off 3 Once you turn on Bottom Lock the Bottom Range X Press menu choice will be displayed 10 60 feet or 3 20 meters nternational Models only Default 15 feet 2D 3D Priority 2D 3D Priority allows you to change the way the 6 beams on the transducer are used in order to prioritize and customize the 2D and 3D display of information 7 2D 3D Priority lt 3D select 2D Only when you wish to look at 2D views and want the 2D information to be updated quickly if you are looking at the 3D 2D Combo View the 3D side of the screen will be empty and the message 3D Disabled will be displayed Select Equal when you are switching between 2D only and 3D 2D views and you want the 2D information to be updated more
97. h as the GPS receiver and have made all the cabling connections required you must test the installation before using the system Thorough testing should be performed with the boat in the water however you can confirm basic operation initially with the boat out of the water as well To test the installation 1 Press the POWER LIGHT key on the control head once to turn on the control head There will be an audible chirp to let you know that you 26 pressed the key and the initial Title screen will appear If the unit does not power up make sure that power is available While the Title screen is shown on the display press the MENU key to display the Start Up Options menu Use the UP or DOWN 4 WAY Cursor keys to position the cursor then the RIGHT Cursor key to select System Status from the Start Up Options menu see the Start Up Options Menu section for more information about these menu choices The System Status Self Test screen will appear NOTE If you wait too long the system will default to whichever menu mode happens to be highlighted and you will have to start again 2 self Test displays results from the internal diagnostic self test including unit serial number Printed Circuit Board PCB serial number software revision total hours of operation and the input voltage See System Status for more information about the Self Test From the System Status screen view accessory connections by pressing the VIEW key See Sy
98. h hanging very close or a fish hanging very close to structure Humminbird fishfinders provide a very good 2 1 2 inches of target separation in shallower than 100 feet of depth Target separation decreases as depth increases due to the need for longer Pulse Width to achieve greater depth See Pulse Width Thermoclines Thermoclines are water layer s of distinctly different temperatures that create a sonar reflection due to the density of the differing water temperatures Typically a thermocline will appear as a continuous band across the display at some distance above the bottom contour Thermoclines are of interest to anglers because fish will suspend above or below the thermocline as they seek the optimum temperature and oxygen levels Time Variable Gain Time Variable Gain is a processing step applied to the sonar return to normalize the data so that objects of equal size i e fish appear to be the same size even if they are separated by a good distance Time Variable Gain is a fundamental attribute of good sonar but is often promoted as a feature Total Screen Update A Humminbird feature that refreshes and updates all the sonar information on the display when a range change occurs Without Total Screen Update only the most recent sonar information would be drawn to the new range and the old sonar information would continue to scroll off the screen at the old range Glossary Sonar Terms Transducer The transducer is part of
99. he LCD screen Each time a new echo is received the old echoes are moved across the LCD creating a scrolling effect When all the echoes are viewed side by side an easy to interpret graph of the bottom fish and structure appears Sonar Frequency High Frequency Low Frequency Low Resolution Greater Resolution Depth Greater Depth Less Dep Deeper Power Output Cycle Peak To Peak Root Mean Square PtP RMS The sound pulses are transmitted at various frequencies depending on the application Very high frequencies 455 kHz are used for greatest definition but the operating depth is limited High frequencies 200 kHz are commonly used on consumer sonar and provide a good balance between depth performance and resolution Low frequencies 83 kHz are typically used to achieve greater depth capability The power output is the amount of energy generated by the sonar transmitter It is commonly measured using two methods e Root Mean Square RMS measures power output over the entire transmit cycle e Peak to Peak measures power output at the highest points The benefits of increased power output are the ability to detect smaller targets at greater distances ability to overcome noise better high speed performance and enhanced depth Capability 3D Sonar Your 900 Series Fishing System uses a six element transducer that transmits at 455 kHz and is capable of reaching depths of 240 ft 75
100. he control head If holes are required to route the cable they must be 3 4 19 mm to allow for the cable connector Secure the NMEA pigtail with electrical tape NOTE Remember to caulk or seal screw holes and drilled holes as needed to protect your boat from water damage The GPS receiver has two wire routing notches Use the cable notch closest to the intended cable route With the cable routed position the GPS receiver in the planned mounting location and mark the mounting holes with a pencil or punch Move the GPS receiver to the side and drill the two 9 64 3 5 mm pilot holes Align the GPS receiver s screw holes over the pilot screw holes and attach with the 8 1 1 4 Phillips head screws Hand tighten only Finish Routing the Cable and Check GPS Receiver Operation After installing a GPS receiver you should perform the following procedure to finish routing the GPS cable to the control head and to check to make sure that the control head is working correctly i secure the cable along its path to the control head as needed with cable ties 2 Plug the GPS receiver cable into the Communications port on the Power 2 Temp Speed Communications A ransducer Cable Collector Insert control head See esting the System Installation to use the system Status start up option and or the GPS Diagnostic View to confirm a good installation 24 Temperature Probe Accessory Installation Install th
101. highlight Set simulation Position on the Navigation main menu 3 Use the RIGHT 4 WAY Cursor Control key to change the Simulation Position setting A confirmation dialog box will appear to allow you to change your mind or to confirm your choice If the cursor was not active before you began this procedure you will see an error message Exit the menu set the cursor then try again b Advanced Set Map Offset allows you to change the map offset used by the 900 Series NOTE The Map Offset will be applied to all maps and not just the map that requires the correction The Map Offset should be cleared if a different map is to be used To change the Map Offset setting 1 Activate the cursor and move it location where the Map Offset will be applied NOTE The cursor must be active in order for this procedure to work 2 Make sure you are in Advanced User Mode then highlight Set Map Offset on the Navigation main menu 3 Use the RIGHT 4 WAY Cursor Control key to set the Map Offset A confirmation dialog box will appear to allow you to change your mind or to confirm your choice If the cursor was not active before you began this procedure you will see an error message Exit the menu set the cursor then try again 97 Clear Map Oftset Advanced Clear Map Offset y Clear Map Offset allows you to clear the Map Offset Clear Map Offset is only accessible if a Map Offset is currently active To Clear Map Offset 1
102. hot and Recording View only 78 Delete Recording optional purchase MMC SD Card Snapshot and Recording View only 78 Delete All Recordings optional purchase MMC SD Card Snapshot and Recording View only 79 Pings Per Second optional purchase MMC SD Card Snapshot and Recording View only 79 Playback Speed optional purchase MMC SD Card Snapshot and Recording View only 80 Stop Playback foptional purchase MMC SD Card ONV isisisi n 80 Sonar Menu Tab 81 A SOL I a eaten eaaerantneensaecseea penesea ments 81 UPON E a nano eae tag aarcenesut teen dsearieees ated 81 UFE E arna E vende eaceignesnetee 82 AU Deam YE Ol oenina E TT NEE 82 FS E Sap E E E N A E A E EEEE EEE AA 82 FSIS OCIS E A E E E E 83 FISH WD BL Referente sarasa rair 83 heal UME sonar ATS VIN OW senarisini sar 84 BOttOM VIQW MPIO 84 ZOOM Widin 29 ZOO Vew OO senn 84 PANTIE SONS TVA E EE EEE E EEE 85 Depth LINCS AQVARCED sumsucnesinserni nni 85 Surface Clutter Advanced voecccccecccecccesesesesesesesesesesesesesesesesesestsvesevevevevevevereses 86 Noise Filter AQVa nc d ceccceccccscscscseesescseesesesesesesesesesesseseseeesesesessserveveeeenenten 86 Max Depim Agvanad ssinesiunsannn ctsnneabtaieaaatdonents 87 Water Type JAQVGICEG iceusss cinnescen cavesiusconcasandnstenacaseavansavesh wiaanisacastaimoddneniniais 8 COON I erriei ene EN E same de nansssussieuttn sectional veseauoiipaecne
103. hot must be enabled 1 Make sure you have installed an optional purchase MMC SD card into your card slot 2 From any view you want to capture press the MARK key When you start a screen capture you will see a message that a waypoint has been created at the point where your cursor is on the screen and the screen will freeze while the snapshot is being saved to the MMC SD card A status dialog box will appear that shows the progress of the save as a percentage and that displays the numbered file name assigned to the BMP file that is being created NOTE For more information see Snapshot and Recording View and Snapshot and Recording X Press Menu NOTE Navigation is not affected by the Screen Snapshot feature Also if Screen Snapshot is enabled but there is no GPS receiver connected pressing the MARK key will capture the screen image and display an error saying that a GPS position fix is required to create a waypoint NOTE The speed of the capture depends on the type of card you use in general SD cards capture the screen taster than MMC cards do 113 To view screen snapshots 1 Make sure that the optional purchase MMC SD card used to capture the screen is installed in your card slot 2 Press the VIEW key until you see the Snapshot and Recording View 3 You can scroll through the whole list of captures in this view using the 4 WAY Cursor keys Highlight a thumbnail using the Up or Down 4 Way Cursor keys then us
104. ically Use the illustration to locate the position of the MMC SD slot cover remove the MMC SD slot cover then insert the MMC SD into the slot The label on the MMC SD should face toward the left side of the unit Press down on the card until it clicks into place and replace the slot cover Then replace and tighten snugly do NOT overtighten as this will not improve water resistance and may damage the cover Inserting an MMC SD into the Card Slot Software Updates Use the MMC SD slot to update the software version of your control head To update the software in your control head plug in the appropriate MMC SD card that contains a software update file the unit will recognize it will tell you what software version your control head is currently running and will ask you if you want to update the software in the unit to match that on the MMC SD card You can obtain software updates from the www humminbird com website Accessory Bus Use the Accessory Bus to expand the functionality of your 900 Series Accessories plug directly into the 900 Series enabling Advanced features such as WeatherSense and the SmartCast Wireless Sonar Link Additional tabs and menu choices will be added to the menu system automatically when an accessory is plugged into the unit In addition multiple accessories can be attached simultaneously See Accessories Menu Tab and 900 Series Accessories in this manual as well as your accessory Ope
105. ich side is active Left Right Default Right P Split Position 50 Split Position Leii Right Split Position allows you to adjust what percentage of the screen is taken up by the left side of any Combo View each view may be adjusted independently you must be in a specific view to adjust the screen size for that view The number setting indicates the percentage taken up by the left side of the Combo View selecting Left sets the left side of the screen to its smallest setting The Split Position menu choice is only available when a Combo View is active To Adjust Split Screen Position 1 Highlight Split Position on the 2D Sonar X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to change the size of the left side of a Combo View Left 30 40 50 60 70 Right Default varies vx Sensitivity 10 Sensitivity Zz ao Sensitivity controls how much detail is shown on the display Increasing the sensitivity shows more sonar returns from small baitfish and suspended debris in the water however the display may become too cluttered When operating in very clear water or greater depths increased sensitivity shows weaker returns that may be of interest Decreasing the sensitivity eliminates the clutter from the display that is sometimes present in murky or muddy water If Sensitivity is adjusted too low the display may not show many sonar returns that could be fish 64 Sensitivity at Low S
106. igating a route This will not delete a previously saved route To Cancel Navigation 1 Highlight Cancel Navigation on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate canceling navigation 3 The Confirm dialog box will appear To cancel navigation press the RIGHT Cursor key once more To avoid canceling navigation press the LEFT Cursor key E Cancel MOB Navigation Cancel MOB Navigation only when MOB Navigation is activated Cancel MOB Navigation removes the Man Overboard MOB waypoint and exits Man Overboard mode This menu choice will only appear when you are currently navigating in Man Overboard mode To Cancel MOB Navigation 1 Highlight Cancel MOB Navigation on the Navigation X Press menu 2 Use the RIGHT 4 WAY Cursor Control key to initiate canceling MOB navigation 3 The Confirm dialog box will appear To cancel MOB navigation press the RIGHT Cursor key once more To avoid canceling MOB navigation press the LEFT Cursor key Remove Target Only if a Target is active Remove Target gt Remove Target removes the waypoint target from the display This menu choice will only appear when a target has already been applied to a waypoint To Remove a Target 1 Highlight Remove Target on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to remove the target E Remove Grid gt Remove Grid Only if a Grid is active Remove Grid remove
107. ight line The TRK is measured in degrees i e 321 where 000 is North 090 East 180 is South 270 is West See Cross Track Error and Course Over Ground 131 GPS amp Navigation Terms Trackplotter Trackplotter describes a navigation device that shows Present Position along with Track Waypoint and Routes but NO MAP in the background See Chartplotter Trolling Grid Trolling Grid is a Humminbird feature that displays a precise reference grid around a waypoint This grid is used as a guide pattern for trolling around a specific area to assure a more efficient and complete coverage of that area Trolling Grid resolution be changed by zooming in or out on the chart The Trolling Grid can also be rotated on the display to orient it for optimal boat course for wave and wind conditions UTC UTC is an acronym for Universal Time Constant UTC is the standard time used in navigation and is the local time in Greenwich England UIC is equivalent to Greenwich Mean Time GMT To display the correct Local Time in a Humminbird GPS unit the user must use the Local Time Zone menu and select the time zone i e EST CST WAAS WAAS is an acronym for Wide Area Augmentation System WAAS is complementary technology to GPS that provides enhanced accuracy through correction signals broadcast from Federal Aviation Administration WAAS Satellites stationed over the USA These secondary signals are automatically received by the stand
108. ilable on the gimbal mounting bracket and may match existing holes on the boat You may choose to use one of these alternate hole patterns 4 Place the gimbal bracket in the chosen position on the mounting Surface and mark the four mounting screw locations using a pencil or center punch NOTE Go to the installation instructions applicable to your transducer GPS Receiver and accessories Make the required installations and then run the cables to your control head mounting location Do not cut any cabling except the power cable If your cables are too short extensions are available from your local dealer or online from www humminbird com Mounting Screws Gimbal Mounting Bracket Washer 9 set the gimbal bracket aside and drill the four mounting screw holes using a 5 32 4 0 mm drill bit 6a If the cables must pass through a hole directly beneath the mounting bracket mark and drill an additional 1 25 mm hole centered between the four mounting holes Route the cables through the 1 hole Place the hole cover over the mounting surface 6b hole then use it to mark the position of the two mounting screws Remove the hole cover drill the two mounting holes using a 9 64 bit Do not install the hole cover at this time or If the cables cannot be routed directly beneath the mounting bracket mark and drill a 1 25 mm hole that will allow you to run the cables close to the bracket Pass the cables through the 1
109. ilable when User Mode is set to Advanced see Setup Menu Tab User Mode Depth Lines To change the Depth Lines setting 1 Make sure you are in Advanced User Mode then highlight Depth Lines on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to turn the Depth Lines setting On or Off Off On Default On Surface Clutter Advanced Surface Clutter 5 io Surface Clutter adjusts the filter that removes surface clutter noise caused by algae and aeration The lower the setting the less surface clutter will be displayed The Surface Clutter menu choice is available when User Mode is Surface Clutter To change the Surface Clutter setting 1 Make sure you are in Advanced User Mode then highlight Surface Clutter on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the surface Clutter setting Low 1 to High 10 Default 5 86 Noise Filter Advanced Noise Filter 4 Off b Noise Filter adjusts the sonar Noise Filter to limit interference on the display from sources such as your boat engine turbulence or other sonar devices The Noise Filter menu choice is available when User Mode is set to Advanced see Setup Menu Tab User Made NOTE The Off setting removes all filtering Low Medium and High settings add progressive filtering of the sonar returns In some deep water situations the High setting may actually make it har
110. indicates it was detected in the far left beam and a hollow fish facing right indicates it was detected in the far right beam When Fish ID is turned off and 83 kHz returns are displayed the 900 Series shows only the raw sonar returns on the display To set Fish ID 1 Highlight Fish ID on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Fish ID setting 3D Markers Symbol Only Symbol Depth Off Default 3D Markers 83 Fish ID Sensitivity 5 Fish ID Sensitivity l D Fish ID Sensitivity adjusts the threshold of the Fish ID detection algorithms Selecting a higher setting allows weaker returns to be displayed as fish This is useful for identifying smaller fish species or baitfish Selecting a lower setting displays fewer fish from weak sonar returns This is helpful when seeking larger species of fish Fish Sensitivity is used in conjunction with Fish ID Fish ID must be On for Fish Sensitivity to affect the ability of the 900 Series to identify sonar returns as fish To change the Fish ID Sensitivity setting 1 Highlight Fish ID Sensitivity on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Fish Sensitivity setting Low 1 High 10 Default 5 ae ID 3D Reference Fish ID 3D Reference AE Fish ID 3D Reference selects the reference line style used in the 3D Sonar View Up draws a line from the fish icon to the su
111. ing these keys NOTE Sonar chart speed is increased during Fast Forward and reversed during Rewind This may result in a reduced quality sonar image since at higher speeds not every Sonar return can be processed 80 Stop Playback optional purchase MMC SD Card only EiStop Playback gt Stop Playback allows you to stop playback of a sonar recording from any view This menu option is only available when you have an optional purchase MMC SD card installed and you are playing back a recording To stop playback of a recording 1 Highlight Stop Playback on any X Press menu 2 Press the RIGHT 4 Way Cursor key to initiate this procedure To start playback use the 4 Way Cursor keys to highlight a recording icon then press the RIGHT 4 Way Cursor key to start playback represented by a green play triangle which appears to the right of the recording icon NOTE During playback the amount of time memory left to play is indicated by the status bar For more information see Snapshot and Recording View D Sonar CARAS 2D Sonar Colors Standard 3D Frame Style 3 2D Beam Select 455kHz Bottom Narrow Structure ID Narrow 0 On 5 Off Auto Fresh On Off Sonar Menu Sonar Menu Tab NOTE Menu choices will vary depending on system settings such as whether the unit is set Fish ID for Advanced User mode or whether a 2D or a 3D View is displayed active Press the
112. ion Line Course Projection Line q Visible gt Course Projection Line allows you to display or hide an arrow extending from the bow of the boat that projects your Current course and shows where the boat will go if you continue on your present course To change the Course Project Line setting 1 Highlight Course Projection Line on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Course Projection Line setting Hidden Visible Default Visible Export All Nav Data Export All Nav Data allows you to export all saved Tracks Waypoints and Routes to an MMC SD card Export All Nav Data Advanced To Export All Navigation Data 1 Make sure you are in Advanced User Mode and that an optional purchase MMC SD card is installed in the slot then highlight Export All Nav Data on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control key to export all navigation data Delete All Nav Data Advanced Delete All Nav Data Delete All Nav Data allows you to delete all saved Tracks Waypoints and Routes This menu choice should be used with caution To Delete All Navigation Data 1 Make sure you are in Advanced User Mode then highlight Delete All Nav Data on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control key to delete all navigation data Continuous Navigation Mode Continuous Navigation Mode q of gt continue to navigate and fish aro
113. ion path between two points and saved in the fishfinder s memory Routes are often used when frequently traveling between two or more locations because it is a faster and more accurate method than repeatedly selecting individual waypoints each time one travels through the same area Routes consist of a Start Waypoint an End Waypoint and a series of waypoints in between Users can begin navigation at the beginning the end to run the route in reverse or at any waypoint in between See Waypoint SD SD is an acronym for Secure Digital An SD card is virtually identical in function to an MMC however the speed at which information can be accessed is generally faster the storage capacity is generally larger and the card has security features which can be used to prevent extracting the data from the card SD is the same format that many digital cameras use See MMC Selective Availability Selective Availability SA is a GPS system feature that can be implemented by the U S Department of Defense DoD to degrade the accuracy of GPS positioning information With SA active the GPS is accurate to within 100 meters 95 of the time With SA inactive the GPS is accurate to within 45 meters 95 of the time Currently SA is inactive and the consumer can enjoy the greater precision GPS provides however the DoD reserves the right to activate SA at any time Glossary Speed Over Ground SOG Speed Over Ground is the measurement of the boat
114. ion system designed and maintained by the U S Department of Defense GPS was originally intended for military use however civilians may also take advantage of its highly accurate position capabilities typically within 10 meters depending on conditions This means that 95 of the time the GPS receiver will read a location within 10 meters of your actual position Your GPS Receiver also uses information from WAAS the Wide Area Augmentation System EGNOS the European Geostationary Navigation Overlay Service and MSAS the MTSAT Satellite Augmentation System satellites if they are available in your area i GPS uses a constellation of 24 ON satellites that continually send radio N signals to the earth Your present position is determined by receiving signals from up to 16 satellites and _ measuring the distance from the B satellites All satellites broadcast a uniquely coded signal once per second at exactly the same time The GPS receiver on your boat receives signals from satellites that are visible to it Based on time differences between each received signal the GPS receiver determines its distance to each satellite With distances known the GPS receiver mathematically triangulates its own position With once per second updates the GPS receiver then calculates its velocity and bearing The GPS Receiver included with your 900 Series Fishing System allows you to combine easy to use FishingGPS chartplotter and n
115. is a permanent sharable waypoint with a large distinctive icon is created at the boat s current position regardless of whether the chart cursor is active or not Any current navigation will be cancelled and the current route discarded without user notification and MOB navigation begins immediately The view is switched to the Chart View automatically when MOB is activated and it is not possible to activate MOB or modify the current route without first canceling MOB navigation Any press of the GOTO key or selection of a GOTO menu item will cause an error beep and a short message will be displayed to the user that will disappear after 2 seconds ZOOM Keys Press the or ZOOM keys while in any of the Navigation Views or the Sonar Zoom View to change the scale of the view to appear closer or farther away Views The views available on your 900 Series are Chart 3d ombo View Chart 2D Combo View 2D Sonar View Chart Chart Combo View Chart Bird s Eye 2D Zoom Combo View View Birds s Eye 3D 2D Combo View Combo View GPS Diagnostic 6 Beam View Sonar View Pa ee ee and Test View Recording View Self Test lew e 2D Sonar View e GPS Diagnostic View e 2D Zoom View e 3D 2D Combo View e 6 Beam Sonar View e Bird s Eye View e Chart Bird s Eye Combo View e Chart Chart Combo View e Chart View e Chart 3D Combo View e Chart 2D Combo View e Snapshot and Recording View o Self Test Vi
116. key being pressed When you do this a Bullseye Cursor is drawn at the top of the screen and is linked to the boat by a yellow line even if the boat is off the screen At the same time a cursor dialog box is displayed at the top of the screen with the distance and bearing from the boat to the cursor position and the latitude longitude coordinates of the cursor When the cursor is active on the display you can also use the 4 WAY Cursor Control key to move the cursor diagonally 50 Chart View with Cursor Present Dist 0 75 istance 094 i e el aE Bearing N 25 43 273 W_080 12 322 Zooming Use the Plus key to Zoom In and the Minus key to Zoom Out showing the cartography at different scales The scale is indicated on the left side of the display If you zoom in beyond the available chart data the display will go into Overzoom mode whereby the last available chart data is amplified to reflect the scale selected If you zoom in so far that no cartography is available a lat lon grid will be drawn instead Chart Info Use the INFO key to get detailed information about the chart If the cursor is active you will see information about the chart objects located near the cursor If the cursor is not active the Chart Info menu will appear You can select the nearest port the nearest tide station or the nearest Current station to see information about any of these objects NOTE The built in UniMap does not contain any Po
117. lay depth scale The Wide RTS Window indicates the sonar intensity through the use of a bar graph The length of the plotted return provides an indication of whether the return is weak or strong The depth of the sonar return is indicated by the vertical placement of the return on the display depth scale 30 Bottom Presentation As the boat moves the unit charts the changes in depth on the display to create a profile of the Bottom Contour he type of bottom can be determined from the return charted on the display A Hard Bottom such as compacted sediment or flat rock appears as a thinner line across the display A Soft Bottom such as mud or sand appears as a thicker line across the display Rocky Bottoms have a broken random appearance NOTE A sloping bottom will be represented as a thicker line across the display Harder bottoms typically will be displayed with red and softer bottoms typically Will be displayed with blue The sonar returns from the bottom structure and fish can be represented as either Structure ID or WhiteLine See Sonar Menu Bottom View for details on how to set the bottom view Structure ID represents weak returns in blue and strong returns in red WhiteLine highlights the strongest sonar returns in white resulting in a Key Functions distinctive outline This has the benefit of clearly defining the bottom on aem p the display Your 900 Series user interface consists of a se
118. le is damaged or corroded Display Problems There are several main conditions or sources of possible interference that may cause problems with the quality of the information displayed on the control head Look in the following table for some symptoms of display problems and possible solutions Problem Possible Cause The control head loses power at high If the power output of your boat s engine is unregulated the control head may be protecting itself using speeds its over voltage protection feature Make sure the input voltage does not exceed 20 Volts When the boat moves at higher speeds The transducer position may need to be adjusted A mix of air and water flowing around the transducer the bottom disappears or suddenly cavitation may be interfering with the interpretation of sonar data See your Installation Guide for weakens or the display contains gaps Suggestions on adjusting the transducer position Electrical noise from the boat s engine may be interfering with sonar reception See Finding the Cause of Noise for more information There are no fish detected even when you Sonar readings may be affected if the transducer is not positioned correctly i e mounted at an angle know they are in the water under the not straight down or there is some kind of mechanical interference either because it is mounted inside boat or sonar readings seem weak or a hull that is too thick for proper sonar transmission the bond between the transduc
119. le only when in Advanced User Mode see Setup Menu Tab User Made To change the Position Format setting 1 Make sure you are in Advanced User Mode then highlight Position Format on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Position Format dd ddddd dd mm mmm or dd mm ss Default dd mm mmm Time Format Advanced International only Time Format q 12 Hour gt Time Format changes the time format used by the unit This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode International models only ime Format selects a 12 hour or 24 hour format for the time of day displayed when Time Date is selected as a Digital Readout on the Sonar View see Select Readouts To change the Time Format 1 Make sure you are in Advanced User Mode then highlight Time Format on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Time Format 12 hour 24 hour Default 12 hour Date Format 4 mm dd yy gt Date Format changes the date format used by the unit This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode International models only Date Format selects the format for the date display when Time Date is selected as a Digital Readout on the Sonar View see Select Readouts To change the Date Format 1 Make sure you are in Advanced User Mode then highlight Date Format on the Se
120. locate the accurately especially in salt water as this affects the accuracy of deep water bottom The Max Depth menu choice is available when User Mode is set to depth readings Advanced see Setup Menu Tab User Made To change the Water Type setting To ch the Max Depth setting St T ENANGE Meme seun 1 Make sure you are in Advanced User Mode then highlight Water 1 Make sure you are in Advanced User Mode and in a 2D Sonar View Type on the Sonar main menu then highlight Max Depth on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Water Type setting Fresh Salt Default Fresh Max Depth setting AUTO 10 to 1000 feet 3 to 330 meters International models only Default AUTO 87 Mmm coe senso vgn wu 2n gt Color Bar allows you to display or suppress the display of the color bar shown in the full screen Sonar View To change the display of the Color Bar 1 Highlight Color Bar on the Sonar Main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the display of the color bar Off On Default On Temperature Graph q Off b Temperature Graph allows you to display or suppress a water temperature graph over the main 2D Sonar View to show temperature changes correlated to recent sonar history Temperature Graph 2D Sonar View only with Temperature input To change the display of the Temperatu
121. lumn The 6 Beam Sonar View also provides information on sonar targets relative to the boat The far right window displays sonar targets which are to the far right of the boat and the far left window displays sonar targets which are to the far left of the boat The remaining windows display sonar targets which are successively closer to the boat The width of coverage is approximately equal to the current depth Depth 6 Beam Sonar History Q Boat Icon Lower Depth Range Upper Depth Range 39 Snapshot and Recording View Snapshot and Recording View displays and allows you to view both screen Snapshot thumbnails and recording icons captured to an optional purchase MMC SD card installed in your unit In addition when you are in the Snapshot and Recording View Start Recording Stop Recording Delete Image Delete All Images Delete Recording Delete All Recordings Pings Per Second Playback Speed and Stop Playback are added to the X Press menu The Snapshot and Recording View displays up to three screen snapshot thumbnails or recording icons on the screen at a time you may have to scroll using the 4 WAY Cursor keys to see the whole list of thumbnails and or icons in this view The selected thumbnail or icon will be highlighted with arrows NOTE The speed of the screen capture or of the recording depends on the type of card you use in general SD cards capture the screen faster than MMC cards do 40 Snapshot
122. ly available from optional purchase MMC SD cards MARK Key Press the MARK key while in any view to mark the position of a waypoint either at the current boat location or if the Cursor is active at the current Cursor location The MARK key only functions if you have the GPS receiver connected or If you have enabled Screen Snapshot from the Accessories menu tab If you have enabled the Screen Snapshot feature pressing the MARK key still creates a waypoint but it also captures the screen image to the optional purchase MMC SD card NOTE You must have an optional purchase MMC SD card installed for the screen snapshot feature to work 34 Navigation is not affected by the Screen Snapshot feature Also if Screen Snapshot is enabled but there is no GPS receiver connected pressing the MARK key will capture the screen image and display an error saying that a GPS position fix is required to create a waypoint GOTO Key The GOTO Key has multiple functions depending on the situation e f the Cursor is active pressing the GOTO key while in any view creates a waypoint and starts navigation towards that waypoint If the Cursor is not active pressing the GOTO key displays the list of waypoints so that you can select the waypoint towards which you want to navigate If the GOTO key is pressed and held for more than 1 5 seconds the Man Overboard MOB function is activated When MOB is activated an MOB waypoint which
123. m q ee ee gt Large q gt dg To change the Fish ID Alarm setting 1 Highlight Fish ID Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Fish ID Alarm setting Off All Large Medium Large Default Off Low Battery Alarm off Low Battery Alarm off 135 Low Battery Alarm sounds when the input battery voltage is equal to or less than the menu setting The battery alarm will only sound for the battery that is connected to the 900 Series The Low Battery Alarm should be set to warn you when the battery voltage drops below the safety margin that you have determined For instance if you are running a trolling motor battery operated you would want to set the Low Battery Alarm to sound before the battery voltage drops too low for it to be used to start your main gasoline powered engine To change the Low Battery Alarm setting 1 Highlight Low Battery Alarm on the Alarms main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Low Battery Alarm setting Off 8 5V 13 5V Default Off Aux Temp Alarm Off Aux Temp Alarm Off 120 with optional purchase temp probe or Temp Speed only Aux Temp Alarm sounds when the water temperature from the Paddlewheel Temperature Probe detected by the Fishing System reaches the Aux Temp Alarm setting which is either set in degrees Fahrenheit or Celsius International Models only For example if the Aux Temp Alarm
124. mat dd mm mmm 12 Hour mm dd Small tenths Off Sonar Tab Advanced Mode Start Up Options Menu Press the MENU key when the Title screen is displayed to access the Start Up Options menu Start Up Options Menu Start Up Options S Press Right Cursor Arrow to Select Transducer not connected Use the UP or DOWN 4 WAY Cursor keys to position the cursor then the RIGHT Cursor key to select one of the following choices If you wait too long the system will default to whichever menu mode happens to be highlighted e Normal e Simulator e System Status Total Screen Update when you change any menu settings that affect the sonar View the view will update immediately i e you don t have to exit the menu to apply the change to the screen see the following paragraphs for more information about each of these choices og Normal Operation Use Normal operation for on the water operation with a transducer connected In addition your 900 Series uses advanced transducer detection methods to determine if a transducer is connected If a functioning transducer is connected Normal operation will be selected automatically at power up and your 900 Series can be used on the water Exit Normal operation by powering your 900 Series off Simulator Use the Simulator to learn how to use your 900 Series before taking your boat on the water The Simulator is a very powerful tool that simulates on the water operati
125. mation 9 Ifaccess to the top mounting hole is not possible due to the selected height of the transducer fully tighten the two lower screws then NOTE Since the Haned ee ene pian simply remove the headed pivot pin and the transducer assembly De te E ee N neh 3 h bI it strikes an object make sure there is sufficient cable slack to accommodate this and tighten the top screw then reassemble motion It is best to route the cable to the side of the transducer so the cable will 6 Confirm that the pivot angle has not changed and that all mounting MOD ee ON UME SERE screws are fully tightened 2 Ifyou will be routing the cable through a hole in the transom drill a 5 8 diameter 16 mm hole above the waterline Route the cable through this hole then fill the hole with marine grade silicone sealant and proceed to the next step immediately Routing the Cable 3 Place the escutcheon plate over the cable hole and use it as a guide to mark the two escutcheon plate mounting holes Remove the plate drill two 9 64 3 6 mm holes then fill both holes with marine grade silicone sealant Place the escutcheon plate over the cable hole and attach with two 8 x 5 8 16 mm wood screws 4 Route and secure the cable by attaching the cable clamp to the transom drill one 9 64 dia 3 5 mm x 5 8 deep 16 mm hole then fill hole with marine grade silicone sealant then attach the cable clamp using a 8 x 5 8 16 mm screw D Plug the
126. more information NOTE See Chart View for more information about each side of this view 46 Chart Chart Combo View Depth Latitude and Longitude Position of Cursor Course Direction that boat is travelling Distance to the Cursor relative to North Reference Bearing to the Cursor Chart Window 1 Cartography Boat Icon Active Cursor Q Track Breadcrumb Trail Chart Window 2 Chart View Chart View shows cartography from the built in UniMap or an optional MMC SD map for the area surrounding your current position The current track also known as the position history or breadcrumb trail showing where the boat has been along with saved tracks waypoints and the current route when navigating are overlaid on the chart You can use the 4 WAY Cursor Control key to shift pan the chart to another area You can use the ZOOM keys to zoom in and out You can use the INFO key to get information on the chart objects near the cursor 41 Chart View with Active Cursor t 43 273 Dist B Fes W oa0 t 32 0 75 0 ogg o fan a Depth Distance to the Cursor Course Direction that boat is travelling Bearing to Cursor relative to North Reference Track Breadcrumb Trail artography O O Wap Scale Active Cursor Q Boat Icon Q Latitude and Longitude Position of Cursor Chart 3D Combo View Chart 3D Combo View shows both the Chart and 3D Sonar views in a combination split screen
127. n the display an arch appears Fish ID Fish ID is a Humminbird feature that uses advanced sonar processing algorithms to determine if a detected object is likely to be a fish When the sonar signal from an object meets strict parameters the unit draws a Fish symbol or icon and the digital depth of the target On DualBeam and DualBeam PLUS units fish detected in the narrow center beam are shown as shaded symbols and fish detected in the wider beam are shown as hollow symbols Fish Symbol A Fish Symbol is the graphic that is displayed on the screen when Fish ID determines that a sonar return is likely to be a fish See Fish D 123 Sonar Terms Freeze Frame Freeze Frame is a Humminbird feature that pauses the sonar scrolling so that the image on screen can be studied with greater detail See Instant Image Update Frequency Frequency is a measure of the number of sound wave cycles per second of a sound impulse transmitted underwater A typical frequency for fishfinders is 200 kHz which offers a good balance of performance under many conditions Lower frequencies such as 50 kHz are capable of penetrating to greater depths but with less resolution Higher frequencies such as 455 kHz offer greater resolution but are limited in depth performance Humminbird uses a variety of frequencies that are optimized for specific applications Grayscale Grayscale is the use of varying shades of gray to represent the s
128. n the water for the control head to maintain the sonar signal If the transom is behind the propeller s it may be impossible to find an area clear from turbulence and a different mounting technique or transducer type should be considered see nside the Hull Transducer Installation Mount the transducer bracket to the boat 1 Remove the transducer mounting template from this manual See Appendix A Transducer Mounting Template SHS 7W 15 380mm from prop s 2 Hold the template on the transom of the boat in the location where the transducer will be installed Align the template vertically matching the lower edge of the transom with the bottom corner of the template If your propeller moves clockwise as the boat moves forward mount the transducer on the starboard side and use the bottom left corner of the template If your propeller moves counter clockwise as the boat moves forward mount the transducer on the port side and use the bottom right corner of the template Using a pencil or punch mark the three mounting holes on the transom Do not mark or drill any other holes at this time Using a 5 32 4 0 mm bit drill the three holes to a depth of approximately 1 25 mm On fiberglass hulls it is best to use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating Use a marine grade silicone sealant to fill the drilled holes Attaching the Bracket 9 Align the metal m
129. nd your current track between two Humminbird Fishing Systems in real time Mark a waypoint at the console and it s instantly available on the second unit No matter where you re at on the boat you ll have access to your critical fishing and navigation information Plus daisy chain InterLink with other System Modules and you ll have a network that lets you share digital data around the boat It s a simply clearly better networking solution Be sure to check out our website www humminbird com for additional new and exciting accessories to grow your 900 Series NOTE Each accessory requires a separate purchase You can visit our website at www humminbird com or contact our Customer Resource Center at 1 800 633 1468 for additional details Specifications Depth Capability 00 0 00 cee 240 ft 75 m 3D 1000 ft 330m 2D Power Output 0 0 0 00 00 1000 Watts RMS 8000 Watts Peak To Peak Operating Frequency 455 kHz and 83 kHz Gs et tcl patent dh uae et eas 83 kHz 74 10 dB 455 kHz 53 10 dB Area of Coverage TEE EPEE TE 2 1 2 Inches 63 5 mm Power Requirement 0 00000 e eee eee 10 20 VDC GD ere ec na ae E E E 480 V x 800 H 8 Diagonal Color TFT MTANSUUCE as he 2 di decaueeestaapaepedaw ered ekwaere Red SHS 7W Transducer Cable Length 121 NOTE Product specifications and features are subject to change without notice NOTE Humminbird ve
130. nding on the situation Freeze Frame Pressing any arrow on the 4 WAY Cursor Control key will freeze the display in the Sonar View and a cursor and cursor dialog box will be displayed The cursor can be positioned on the Sonar View using the 4 WAY Cursor Control key Active Cursor In any Bird s Eye View the 4 WAY Cursor Control key controls the motion of the eyepoint In any Chart View the 4 WAY Cursor Control key pans the charts NOTE In either Freeze Frame or Active Cursor mode you can also make the cursor move diagonally by pressing in between two of the arrows on the 4 WAY Cursor Control key Menu Selection Use the DOWN or UP arrow keys to select a menu choice from the menu list then use the LEFT or RIGHT arrow keys to change a menu setting Snapshot and Recording View In the Snapshot and Recording View highlighting a recording icon and pressing the Right 4 WAY Cursor Control key starts recording playback and the Right and Left keys are used to control the speed of playback Change 3D Perspective Use any arrow key to change the perspective in the 3D Sonar View Subsequent presses of arrow keys rotate and tilt the 3D representation NOTE Menu choices are implemented and saved immediately no further action IS required 33 VIEW PRESET keys The VIEW PRESET keys are used to program your three favorite views for quick retrieval Instead of using the VIEW key to cycle through every view to find the one you want
131. ng Delete All Images from the Snapshot and Recording X Press menu Working with screen snapshots is a four step process 1 Enabling Screen Snapshot from the Accessories Menu 2 Making a Screen Snapshot using the MARK key 3 Viewing a Screen Snapshot using the Snapshot and Recording View 4 Deleting a Screen Snapshot using the Snapshot and Recording X Press menu For more information see Accessories Menu Tab Using Screen Snapshot and Snapshot and Recording X Press Menu 41 When you start a screen snapshot you will see a message that a waypoint has been created at the point where your cursor is on the screen and the screen will freeze while the snapshot is being saved to the MMC SD card A status dialog box will appear that shows the progress of the save as a percentage and that displays the numbered file name assigned to the BMP file that is being created Snapshot filenames begin with the letter S For more information see Accessories Menu Tab Using Screen Snapshot procedure and Snapshot and Recording X Press Menu Recording and Playback From the Snapshot and Recording View you can use the X Press menu to start and stop recording and to change the pings per second which alters the detail level of the recording Once you are recording already playing back a recording and screen snapshot viewing are not allowed and the only Sonar Recording menu choices available in the X Press menu are Stop Recording an
132. nsert O Screws NOTE You may wish to dress the cabling with nylon wire ties in order to hold the 3 Cable Collector Cover cables together and create a cleaner assembly O abon Insert Sot on Cover The Humminbird 900 Series control head is now ready for operation Connecting the Control Head Power Cable to the Boat nea l l lt la If a fuse terminal is available use crimp on type electrical A 6 2 m long power cable is included to supply power to the control head connectors not included that match the terminal on the fuse You may shorten or lengthen the cable using 18 gauge multi stranded panel Attach the black wire to ground and the red wire to copper wire positive 12 VDC power Install a 3 Amp fuse not included for protection of the unit Humminbird is not responsible for over CAUTION Some boats have 24 or 36 Volt electric systems but the control head voltage of over current failures MUST be connected to a 12 VDC power supply Or The control head power cable can be connected to the electrical system of the boat at one of two places a fuse panel usually located near the console 1b If you need to wire the control head directly to a battery obtain or directly to the battery and install an inline fuse holder and a 3 Amp fuse not included for the protection of the unit Humminbird is not responsible for overvoltage or over current failures NOTE In order to minimiz
133. ntial Beacon Receiver DBR that connects to the GPS receiver The advent of WAAS has largely negated the need for the added expense of a DBR in the United States Distance To Go Distance To Go is the straight line distance between Present Position and the Destination Waypoint DIG and SOG Speed Over Ground are used to calculate Time To Go See Time to Go and Speed Over Ground 129 GPS amp Navigation Terms Estimated Position Error EPE Estimated Position Error is a calculation that indicates the potential position inaccuracy the user may experience due to a variety of GPS factors which include satellite position in the sky signal strength and others factors Fix Type Fix Type indicates whether the GPS receiver is providing 2D fix or 3D fix A 2D fix requires only three satellites and provides only latitude and longitude A 3D fix requires four or more satellites and provides latitude longitude and altitude GPS GPS is an acronym for Global Positioning System GPS provides accurate position latitude longitude altitude information virtually anywhere on the earth through satellite technology and personal receivers on the ground A series of geosynchronous satellites broadcast a unique signal toward the earth once per second A GPS receiver such as that included with many Humminbird products receives the signals from these satellites and is able to determine position based on very slight differences in the time each signal is
134. o any desired heading using Grid Rotation from the Navigation Main menu To remove the trolling grid choose Remove Grid from the Navigation X Press Menu Chart View with Grid C Wap Scale Waypoint Trolling Grid NOTE Only one waypoint can have either a target or a grid at one time If you apply a target or a grid to a new waypoint the original waypoint will lose its target or grid NOTE The spacing of the rings on the waypoint target and the spacing of the grid lines on the trolling grid is the same as the length of the scale bar on the left edge of the display Zooming in or out will decrease or increase the spacing respectively o9 Save Edit or Delete a Route Save the current route While you are navigating the current route can be saved From the Navigation X Press Menu select Save Current Route and press the RIGHT Cursor key Navigation will continue Display the Routes submenu From any view press the MENU key twice to display the Main Menu System then use the RIGHT Cursor key to select the Navigation tab Select Routes and press the RIGHT Cursor key to display the Routes submenu Create a route From the Routes submenu select Create and press the RIGHT Cursor key A Route Edit screen will be displayed with an empty route You can name the route add waypoints to the route from the list of all waypoints and order the waypoints in the route using the Cursor keys Edit a saved route From the Routes
135. o control is selected as the active side see Sonar X Press Menu Active Side or Navigation X Press Menu Active Side for more information A green arrow points to the side that is active You can also adjust the size of the left side of a split screen see Sonar X Press Menu Split Position or Navigation X Press Menu Split Position for more information NOTE See Bird s Eye View and Chart View for more information about each side of this view 45 Chart Bird s 7 Combo View SPEED mph J 6 Depth Latitude and Longitude Position of Cursor O Course Direction that boat is travelling Distance to the Cursor relative to North Reference Bearing to the Cursor Bird s Eve Window Cartography O Boat Icon Active Cursor Q Track Breadcrumb Trail Chart Window Q Chart Chart Combo View Chart Chart Combo View shows two versions of the Chart view in a combination split screen so that you can see the position of the boat on one side while you zoom in or perform other functions on the other You can perform any of the functions for the Chart view but only on the side of the view you have selected as the active side see Sonar X Press Menu Active Side or Navigation X Press Menu Active Side for more information A green arrow points to the side that is active You can also adjust the size of the left side of a split screen see Sonar X Press Menu Split Position or Navigation X Press Menu Split Position for
136. ocation NOTE When you save a waypoint by any of these methods a numerical waypoint name is automatically assigned You can edit the waypoint information later to give it a different name and select an icon to represent it see Waypoint submenu on the Navigation Main Menu Tab Display the Waypoints Submenu From any view press the MENU key twice to display the Main Menu System then use the RIGHT Cursor key to select the Navigation tab Select Waypoints and press the RIGHT Cursor key to display the Waypoints submenu Program a specific position as a waypoint To create a waypoint that is NOT your current position from the Waypoints submenu select the Create option and press the RIGHT Cursor key Use the Cursor keys to program a waypoint name latitude longitude and icon before selecting Save 03 Edit a waypoint From the Waypoints submenu select Edit and press the RIGHT Cursor key to display a list of saved waypoints Select the waypoint you want to edit and press the RIGHT Cursor key Use the 4 WAY Cursor Control key to move from field to field and the UP and DOWN Cursor keys to changes values once you are in a field In the Waypoint Name Latitude and Longitude fields use the UP and DOWN Cursor keys to change the letter or number All upper and lower case letters are available as well as digits 0 9 and some punctuation characters In the Waypoint Icon field use the UP and DOWN Cursor keys to change the icon used to represent the
137. ocedure 4 Route the GPS receiver cable through the stem and continue with 1 Determine the best location to mount your GPS receiver Preplan the planned route you chose in step 1 and test the cable routing to your control head before any drilling or cutting of your boat surfaces If you have purchased hardware to 5 Attach the GPS receiver to its base using the included 6 7 8 stem mount your GPS receiver follow the instructions included with screws that hardware to mount the stem antenna pole NOTE AS EC10 10 extension cables are available from Humminbird if your planned routing exceeds 20 6 m Maximum cable length including extensions should not exceed 50 16 m NOTE Remember to caulk or seal screw holes and drilled holes as needed to protect your boat trom water damage 2 screw on the receiver base to the stem first making sure that the stem pipe does not protrude from the receiver base This adds protection to the cable when pulling It through the pipe stem In addition to this de burr the pipe edges to reduce cable abrasion receiver feceiver Base Stem Pipe NMEA Pigtail Taped Mounting Screws NMEA Pigtail Cable Out 22 Access Under Mounting Location Follow these steps to deck mount the GPS receiver when routing the cable down through the mounting location 1 Determine the best location then test route the 20 6 m cable from the mounting location to the control head
138. of a split screen see Sonar X Press Menu Split Position tor more information The 3D side of the view uses a combination of the sonar returns from each of the six transducer elements to create a 3 dimensional wireframe representation of the bottom The graphic depiction of the bottom provides you with an effective tool for understanding the terrain beneath the boat The boat icon represents the location of your boat in relation to the on screen information The most recent sonar returns are charted on the upper right side of the screen and move to the lower left as new information is received The width of coverage is approximately equal to the depth Depth range is automatically selected to keep the bottom visible on the display In some situations the selected point of view may prevent the display of some information due to the slope of the terrain An option is available to change the perspective or viewpoint in order to let you see information that would otherwise be masked by the terrain Use the 4 WAY Cursor Control key to change the perspective The perspective can be re set to the default view by selecting Reset View from the X Press menu 36 If a return meets certain criteria one of 18 kinds of fish symbols will be assigned There are three different size fish symbols to indicate the intensity of the return and each of the six beams has a unique set of fish symbols see Fish ID on the Main Menu Sonar Tab for more informa
139. ombo Views A faster speed shows less history and is preferred by most anglers however the sonar information moves across the display quickly A slower speed keeps the information on the display longer but the bottom becomes compressed and may be difficult to interpret Adjust 3D History to your personal preference To adjust the 3D History 1 Highlight 3D History on the 3D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 Way Cursor Control keys to increase or decrease the 3D History setting Least 2 9 Most Default 4 70 Reset 3D View Reset 3D View resets the orientation 3D Bottom Zoom and 3D Lower Range and is only available on the 3D Sonar X Press Menu when you are in the 3D Sonar or the 3D 2D Sonar Combo Views jReset 3D View To Reset 3D View 1 Highlight Reset 3D View on the 3D Sonar X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to reset the view V2 2D 3D Priority lt 3D gt 2D 3D Priority 2D 3D Priority allows you to change the way the 6 beams on the transducer are used in order to prioritize and customize the 2D and 3D display of information Select 2D Only when you wish to look at 2D views and want the 2D information to be updated quickly if you are looking at the 3D 2D Combo View the 3D side of the screen will be empty and the message 3D Disabled will be displayed Select Equal when you are switching between 2D only and 3D 2D views and you want the 2D information to
140. on Advanced with Speed paddlewheel only c cccesceesceesee 108 Local Time Zone Advanced viecciccccccccccccscscscscsesesesescsesseseseseseresereseevveeeneen 108 Daylight Saving Time Advanced s es 108 Position Format Advanced o cecccccccecccsesesesesesesessseseesesesesesesesereseeveeeeeen 108 Table of Contents Views Menu Tab Accessories Menu Tab Using SUN Snags NOT suree nr Troubleshooting 900 Series Doesn t Power Up s ssesssissiiiessiirssrirsriresrrresrrrrsrrressrenn 900 Series Defaults to Simulator with a Transducer Attached Display Problems Finding the Cause of Noise 1 Year Limited Warranty Humminbird Service Policy 900 Series Accessories 112 112 114 114 114 115 116 117 118 119 yil Specifications 121 Glossary 122 Appendix A Transducer Mounting Template SHS 7W 132 Contact Humminbird 135 NOTE Entries in this Table of Contents which list International only are only available on products sold outside of the US and Canada by our authorized International Distributors To obtain a list of authorized International Distributors please visit our website at www humminbird com or contact our Customer Resource Center at 1 800 633 1468 to locate the distributor nearest you NOTE Entries in this Table of Contents which list with Speed Input or with Jemperature Input may require the purchase of separate accessories You can visit our website at www humminbird com to order th
141. on providing a randomly updated display We recommend going through this manual while using the Simulator since all of the menus function and affect the display the way they actually do when in Normal operation Simulator 60 NOTE To get the full benefit of the Simulator it is important to select Simulator manually trom the Start Up Options menu as opposed to letting the 900 Series enter Simulator automatically as it will if a transducer is not connected and you do nothing during power up Manually selecting Simulator from the Start Up Options menu allows you to pre contigure your 900 Series for on the water operation Any menu changes you make will be saved for later use A Simulation message will appear on the display periodically to remind you that you are using the Simulator Exit the Simulator by powering your 900 Series off System Status Use System Status to view system connections and to conduct a unit self test Exit System Status by powering your 900 Series off The following screens are displayed in turn when you press the VIEW button when using System Status e Self Test e Accessory Test e GPS Diagnostic View Self Test Accessory Test Self Test displays results from the internal diagnostic self test including unit Accessory Test lists the accessories connected to the system serial number Printed Circuit Board PCB serial number software revision total hours of operation and the inpu
142. onal purchase MMC SD Card Snapshot and Recording View only Delete Recording gt Delete Recording allows you to delete a single sonar recording from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed you are in Snapshot and Recording View To delete a recording 1 On the Snapshot and Recording View use the UP and DOWN 4 Way Cursor keys to highlight the recording you want to delete 2 Highlight Delete Recording on the Snapshot and Recording X Press menu 3 Press the RIGHT 4 Way Cursor key to initiate this procedure 4 A Confirm Dialog box will appear Select Yes to delete the recording or No to cancel the operation Delete All Recordings Delete All Recordings gt optional purchase MMC SD Card Snapshot and Recording View only Delete All Recordings allows you to delete all the recordings at once from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are in Snapshot and Recording view To delete all recordings 1 From the Snapshot and Recording View highlight Delete All Recordings on the Snapshot and Recording X Press Menu 2 A confirmation dialog box will ask if you want to delete all recordings Select Yes to delete or No to change your mind 79 Pings Per Second 10 Pings Per Second A Auto optional purchase MMC SD Card Snapshot
143. optional transducer WideSide uses three sonar beams pointing to the left right and down Beams pointing to the left and right are effective for spotting fish and structure near the surface or on the bank The downlooking beam provides depth information directly below the boat X Press Menu X Press Menus are a Humminbird feature that make the most commonly used menu selections available with one press of the MENU key Items that appear on the X Press Menu are related to the current view and present the most logical choices for that view Sonar View X Press menus will differ from Chart View X Press menus etc X Press menus are one of the principal reasons that Humminbird products are easier to use Glossary Zoom Zoom is a feature that focuses in on a smaller area of the bottom to provide enhanced resolution With enhanced resolution the angler can more easily see fish hanging in structure or multiple fish hanging close together Split screen zoom divides the display into the full range view on the right and the zoomed view on the left Humminbird offers One Touch Zoom which allows the zoom feature to be easily accessed from the regular sonar view with just one key press eliminating the need to use menus to access the feature Zoom Bottom Lock Bottom Lock Zoom is a feature that focuses on a smaller area just above the bottom to provide enhanced resolution Unlike regular zoom it continuously graphs the bottom
144. ormal operation If no transducer is detected or one is not connected the unit will go into Simulator mode and will indicate this by displaying the word Simulator on the control head display NOTE The transducer must be submerged in water for reliable transducer detection d If the bottom is visible on screen with a digital depth readout the unit is working properly Make sure that the boat is in water greater than 2 ft 6 m but less than the depth capability of the unit and that the transducer is fully submerged since the sonar signal cannot pass through air 4 Ifthe unit is working properly gradually increase the boat speed to test high speed performance If the unit functions well at low speeds but begins to skip or miss the bottom at higher speeds the transducer requires adjustment Angling the rear of the transducer downward and or lowering the transducer farther into the water will help achieve depth readings at high speeds NOTE Due to the wide variety of boat hulls it is not always possible to obtain high speed depth readings NOTE It is often necessary to make several incremental transducer adjustments before optimum high speed performance is achieved Once you have reached a consistently good sonar signal at the desired speeds you are ready to lock down the transducer settings 5 Mark the transducer bracket location on the transom with a pencil then pop up the bracket to reveal the mounting screws Tighten
145. ounting bracket with the mounting holes The center slot should be above the two outer slots This bracket and all other hardware supplied is top quality stainless steel for maximum strength and corrosion protection Insert the three 1 25 mm flat head wood screws into the drilled holes but do not completely tighten Attach the pivot to the transducer 1 Attach the pivot to the transducer body using the two 1 4 20 x 5 8 16 mm machine screws toothed washers and square nuts The toothed washers must fit on the inside of the transducer ears between the pivot and the ears The square nuts will be prevented from rotating by the pocket in the back of the pivot An Allen wrench is provided which fits all the 1 4 20 screws but do not fully tighten the screws at this time Attach the Pivot Insert the Square Nuts O Pivot O loothed Washer Machine Screw O Square Nut Mount the transducer pivot assembly to the bracket 1 Slide the assembled transducer into the metal bracket from the bottom aligning the large hole at the top of the bracket with the hole in the pivot Insert the headed pin through the pivot holes in the bracket and pivot The headed pin can be inserted from either side of the bracket Place the nylon washer over the opposite end of the headed pin Place the stainless washer over the 1 4 20 x 5 8 screw threads then insert into the opposite end of the headed pin and finger tighten only The
146. ove the track completely from the display see Edit Delete or Hide Saved Tracks NOTE When you save a track a name is automatically assigned The track name consists of a date time stamp but can be re named later see Edit Delete or Hide Saved Tracks Clear the current track From the Navigation X Press Menu select Clear Current Track and press the RIGHT Cursor key The track will be removed from the display and discarded 06 Edit Delete or Hide Saved Tracks Display the Tracks Submenu From any view press the MENU key twice to display the Main Menu System then use the RIGHT Cursor key to select the Navigation tab Select Tracks and press the RIGHT Cursor key to display the Tracks submenu Edit a saved track From the Tracks submenu select Edit and press the RIGHT Cursor key to display the list of saved tracks Select the track you want to edit and press the RIGHT Cursor key When the Edit Track dialog box appears use the Cursor keys to move between fields In the Track Name field the UP and DOWN Cursor keys change the letter or number All upper and lower case letters are available as well as digits 0 9 and some punctuation characters You can exit the Track Name field with the LEFT and RIGHT Cursor keys or by pressing the EXIT key Select Save and press the RIGHT Cursor key to save your changes Delete a saved track From the Tracks submenu select Delete and press the RIGHT Cursor key to display the list of saved track
147. own Point dB Down Point The dB Down Point is the standard decibel level at which the sonar cone angle is measured and is written as 10 dB or 3 dB Measurements at smaller down points bigger negative numbers indicate that the less intensive sonar signals are being used for the measurement Glossary Display FSTN FSTN is an acronym for Film Super Iwist Nematic FSTN is a monochrome display technology characterized by black high contrast pixels All monochrome fixed mount Humminbird products use FSTN technology DualBeam PLUS DualBeam PLUS is a Humminbird sonar configuration that uses two sonar beams simultaneously and combines the information from both beams into one view by overlapping the data on screen or shows each beam individually side by side or permits each beam to be viewed individually full screen Feature Memory Feature Memory is a Humminbird feature that retains the user s menu settings in permanent memory Settings are retained even when the unit is powered off indefinitely Fish Arch A Fish Arch is the apparent arch that appears on the display when any object moves through the sonar cone The arch results from a gradual decrease in distance to an object as it moves into the sonar cone The distance to an object changes due to the conical shape of the sonar beam which causes the distance to be greater at the edges of the beam than at the center of the beam When this distance change is graphed o
148. r mode or whether a 2D or a 3D View is currently displayed active jReset 3D View 7 2D 3D Priority 3D 3D Sonar X Press Menu 68 Active Side Active Side allows you to select which side WP Active Side q Left p of a Combo View will be active key presses will only affect the active side of the screen When a menu is displayed the non active side of the screen will be grayed out at any other time a green arrow will point to the active side Combo Views usually display sonar on the left with charts or Bird s Eye usually on the right The Active Side menu choice is only available when a Combo View is active To select the Active Side 1 Highlight Active Side on the 3D Sonar X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to change which side is active Left Right Default Right P Split Position 50 Split Position Left right Split Position allows you to adjust what percentage of the screen is taken up by the left side of any Combo View each view may be adjusted independently you must be in a specific view to adjust the screen size for that view The number setting indicates the percentage taken up by the left side of the Combo View selecting Left sets the left side of the screen to its smallest setting The Split Position menu choice is only available when a Combo View Is active To Adjust Split Screen Position 1 Highlight Split Position on the 3D Sonar X Press Menu 2 Use the RIGHT
149. rations Manual for additional details Accessory Bus NOTE Accessories to enable WeatherSense and the SmartCast Wireless Sonar Link require separate purchases You can visit our website at www humminbird com or contact our Customer Resource Center at 1 800 633 1468 for additional details Installation Overview Please read all instructions that are relevant for your configuration before beginning the installation process NOTE Installation procedures will depend on product configuration The 900 Series has a wide variety of configurations zoom MOB Accessory Bus Sonar Transducer w Temperature Speed through water Optional Y Cable GPS Receiver Power WeatherSense Temperature SmartCast Wireless Sonar Link Inside the boat there is often a channel or conduit used for other wiring this can be used to route cables Be sure to route the cable as far as practical from the antenna cable of VHF radios or tachometer cables to reduce the possibility of interference The transducer and GPS receiver cables should not be cut and care should be used not to damage the cable insulation Basic installation tasks that you must perform include e Installing the control head choosing either gimbal or in dash mounting where in dash mounting requires a separate purchase e Installing the transducer choosing either the transom mount inside the hull mount or trolling motor mounting method e Ins
150. re Graph 1 In the 2D Sonar View highlight Temperature Graph on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the display of water temperature Off On Default On 88 DR nav ASAA Navigation Menu Tab Saved Tracks North Up North Reference T 2 Press the MENU key twice to access the Main Menu System then press the RIGHT cursor key to select the Navigation tab NOTE Menu choices will vary depending on system settings Trolling Grid Rotation Trackpoint Interval 1 second Track Min Distance rue 0 5m Track Color Range om WGS 84 Default Course Projection Line Visible Export All Nav Data Delete All Nav Data Continuous Navigation Mode Off P Navigation Menu Current Track gt To view the Current Track Submenu Track submenu 1 Highlight Current Track on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control keys to view the Current Track submenu Current Track Save P Current Track Submenu The Current Track Submenu contains the following menu choices Save Current Track allows you to save the current track Clear Current Track allows you to clear the current track Appearance allows you to change the style and color of the current track Breadcrumb Trail Dashed Line Solid Line or Wide Line and if a line the color of the line or Color By Depth If you choose Color By Depth you cannot choose one color to
151. received and the receiver s knowledge of the location of each of the satellites Heading Heading describes the direction the boat is pointing and is measured in degrees i e 321 where 000 is North 090 East 180 is South 270 is West Due to wind and waves the boat is often traveling in a slightly different direction than it is heading and therefore Heading is often confused with Course Over Ground See Course Over Ground Map Datum A Map Datum refers to a particular survey of the earth s surface that was referenced when creating a chart i e WGS84 Since the earth is not flat and not even consistently round a mathematical model must be used to translate coordinates from the sphere of the earth to the flat surface of a chart Glossary This mathematical model is the Map Datum Historically many different Map Datums have been used around the world to create maps often a reference to the Map Datum can be found in the legend of a paper map It is important to select the correct Map Datum setting in your fishfinder when comparing GPS position to a paper chart to avoid slight position inaccuracies Almost all electronic charts use the WGS84 Map Datum and therefore they do not require setting changes MMC MMC is an acronym for Multi Media Card An MMC is a postage stamp sized memory device used to store electronic data such a maps waypoints routes and other information MMC is a very rugged format suitable for the marine en
152. red and saved automatically Once you have created a screen capture a screen capture thumbnail is added to the Snapshot and Recording View and is available to view at a later date See the full sized image by highlighting a thumbnail using the Up or Down 4 Way Cursor keys then using the Right 4 Way Cursor key to view the full image A border around the full size screen snapshot indicates that it is just a Screen snapshot not a live view You can delete the highlighted image or all images by selecting a thumbnail and using Delete Image or using Delete All Images from the Snapshot and Recording X Press menu You can view these captures on the Snapshot and Recording View which shows any existing thumbnails of the screen captures along with any icons representing sonar recordings NOTE You must have an optional purchase MMC SD card installed for the Screen Snapshot feature to work NOTE Ifyou use your MMC SD card in two different Fishfinder units that have different screen sizes the recordings made on one unit will still be present on the card but will be represented by the Unavailable icon circle with a slanted line through it on the Snapshot and Recording View on the other unit To turn Screen Snapshot on or off 1 Highlight Screen Snapshot on the Accessories main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to turn Screen snapshot On or Off Off On Default Off To make a screen snapshot Screen Snaps
153. represent the track a color range will represent the different depths on the track instead from light green shallowest to black deepest You can change the depth range associated with black by using Track Color Range menu setting see Navigation Main Menu Track Color Range Current Track allows you to view the Current 89 Saved Tracks Saved Tracks b Saved Tracks allows you to view the Saved Tracks submenu To view the Saved Tracks Submenu 1 Highlight Saved Tracks on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control keys to view the Saved Tracks submenu pem Tracks Default Saved Tracks Submenu The Saved Tracks Submenu contains the following menu choices Edit allows you to select a previously saved track and edit its name whether it is visible or not and its appearance Delete allows you to delete a track from a list of previously saved tracks Default sets the appearance of the track created by selecting Save Current Track Waypoints gt To view the Waypoints Submenu Waypoints allows you to view the Waypoints submenu 1 highlight Waypoints on the Navigation main menu 2 Use the RIGHT 4 WAY Cursor Control keys to view the Waypoints submenu pan Waypoints Submenu The Waypoints Submenu contains the following menu choices Create allows you to create a new waypoint and edit it immediately The current boat position will be used as the default but you can set th
154. rface plane Down draws a line from the fish icon to the bottom contour and Both draws both lines To change the Fish ID 3D Reference setting 1 Highlight 3D Fish ID Reference Line on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Fish ID 3D Reference setting Surface Both Bottom Default Bottom a Window Real Time Sonar RTS Window d RTS Window sets the RTS Window to either Wide or Narrow or turns it off in the Sonar View The RTS Window always updates at the fastest rate possible and only displays returns that are within the transducer beam See Getting Started Using Your 900 Series Real Time Sonar RTS Window for more information To change the RTS Window setting 1 Highlight RTS Window on the Sonar main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the RTS Window setting Wide Narrow Off Default Narrow RTS Window Wide RTS Window Off 84 Bottom View Bottom View ESS Bottom View selects the method used to represent bottom and structure on the display Structure ID represents weak returns in blue and strong returns in red WhiteLine highlights the strongest sonar returns in white resulting in a distinctive outline This has the benefit of clearly defining the bottom on the display See Bottom Presentation for more information To adjust the Bottom View 1 Highlight Bottom
155. rifies maximum stated depth in saltwater conditions however actual depth performance may vary due to transducer installation water type thermal layers bottom composition and slope POLICY ON ENVIRONMENTAL COMPLIANCE It is the intention of Humminbird to be a good corporate citizen and comply and meet all known and applicable environmental regulations in the areas and countries where our products are sold We will promote and implement environmentally sound processes in support of national and international regulations ROHS STATEMENT Product designed and intended as a fixed installation or part of a system in a vessel may be considered beyond the scope of Directive LO0Z 95 EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment WEEE STATEMENT Product designed and intended as a fixed installation or part of a system in a vessel may be considered beyond the scope of Directive LO0Z 96 EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment WEEE CALIFORNIA PROPOSITION 65 STATEMENT Lead in cable jackets and boots is restricted to 300 parts per million or less as determined by ICP AES test methods Glossary Alarm Depth Depth Alarm is a user controllable audible alert that sounds when depth is less than or equal to the setting Alarm Temperature Temperature Alarm
156. ronics Association standard for data communication Wireless Sonar Link WSL purchase the Wireless Sonar Link WSL accessory to receive remote sonar signals from a SmartCast Remote Sonar sensor RSS Radio signals from the RSS are received by the WSL and are transmitted over the Accessory Bus to the 900 Series PC Connect Cable Purchase the PC Connect Cable to connect the 900 Series Fishing System to a PC in order to upload product software updates and new features obtained from www humminbird com This accessory requires the MSWindows compatible HumminbirdPC software downloaded from our website to your PC in order to communicate with the 900 Series Fishing System Downriggers are the key to catching fish you otherwise couldn t even touch And now Humminbird s CannonLink Downrigger Controller makes operation of up to six Cannon Mag 20 DT or Mag 20 DI HS downriggers incredibly easy Using the controls on your Fishing System deploy or retrieve downriggers hold a specific distance off the bottom cycle downriggers between two depths and adjust the Positive lon Control Even see temperature and water clarity at depth and speed at the ball right on screen when using the Cannon Speed n lemp You ll never be shorthanded again just make adjustments from the helm while your mate rigs the lines and brings in the fish 120 With the new InterLink Network Connection you can now share GPS position waypoints routes a
157. roper recesses on the cable collector insert The cable connectors are keyed to prevent reverse installation so be careful not to force the connectors into the wrong slots If you don t have a cable for every hole in the insert install the blank plugs to protect the control head from the weather Plug Cable Connector Assembly to 10 While holding cables in place in Back of Control Head the cable collector insert thread the cables through the slot in the bottom of the cable collector cover line up the cable collector insert and cover then slide the cover into place on the insert Power O Temp Speed Communications Transducer Cable Collector Insert NOTE The tab on the Cable Collector insert goes into the slot on the cover 10 Attach the cable collector insert to the cable collector cover using the 2 Phillips screws provided 11 Place the control head back onto the mounting bracket Plug in the cable collector assembly to the back of the control head Cable connectors and cable sockets are keyed to prevent reverse A installation so be careful not to force the connectors into the wrong sockets Once the cable collector and all cables are plugged into the back of the control head lock the assembly into place by threading the knurled screw into the threaded insert on the back of the housing Adjust the control head to the desired viewing angle and secure by tightening the gimbal knobs Cable Collector I
158. rsor Control keys to increase or decrease the Upper Range setting 0 to 990 feet 0 to 327 meters International models only Default 0 65 Lower Range Auto Lower Range Auto SS 1000 Lower Range sets the deepest depth range that will be displayed Automatic is the default setting When in automatic mode the lower range will be adjusted by the unit to follow the bottom selecting a specific setting locks the depth range into Manual mode Use both Upper and Lower Range together to view a specific depth range manually when looking for fish or bottom structure YJ will be displayed in the lower right corner of the screen when you start manually adjusting the Lower Range to indicate that you are in Manual mode For example if you are fishing in 60 feet of water but are only interested in the first 30 feet surface to a depth of 30 feet you should set the Lower Depth Range limit to 30 The display will show the 0 to 30 foot range allowing you to see a more detailed view than you would see if the display went all the way to the bottom NOTE A minimum distance of 10 feet will be maintained between the Upper and Lower Range regardless of the settings entered manually To adjust the Lower Range 1 Highlight Lower Range on the 2D Sonar X Press Menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to increase or decrease the Lower Range setting AUTO 10 to 1000 feet 3 to 330 meters International models only Default AUTO
159. rt Tide or Current information This information is only available from optional purchase MMC SD cards Nearest Port The position and services information for the nearest port to your present position will be displayed Press the EXIT key to remove the information box and the Bullseye Cursor will be centered over the port position The Cursor Information Boxes will indicate the distance and bearing to the port from your present position Nearest Tide Station Tide information for the nearest tide station to your present position will be displayed This includes the position of the station and the times of the high and low tides for today s date A tide graph is also displayed showing the rise and fall of the tides for the 24 hour time period encompassing the date You can change the date to look at tide information before or after the date displayed by pressing the LEFT or RIGHT Cursor key respectively Press the EXIT key to remove the information box and the Bullseye Cursor will be centered over the tide station position The cursor information boxes will indicate the distance and bearing to the tide station from your present position 51 Nearest Current Station Current information for the nearest current station to your present position will be displayed This includes the position of the station and the current changes for today Two graphs are also presented that show the time direction and flow speed of the current changes for the 24 ho
160. s Select the track you want to delete and press the RIGHT Cursor key You will be asked to confirm deletion before the track is actually deleted Hide or display a saved track From the Tracks submenu select Visibility and press the RIGHT Cursor key to display the list of saved tracks Select the track you want to hide or display and use the Cursor keys to select Hidden or Visible Press the EXIT key to return to the Tracks submenu Man Overboard MOB Navigation As soon as you know that you have a man overboard you should activate MOB navigation to maximize chances for a successful rescue MOB navigation allows you create an MOB waypoint to locate the point at which your man went overboard and the relation of the boat to that point When MOB is activated an MOB waypoint which is a permanent sharable waypoint with a large distinctive icon is created at the boat s current position regardless of whether the chart cursor is active or not Any current navigation will be cancelled and the current route discarded without user notification and MOB navigation will begin immediately A line will be drawn from the boat s current position to the MOB waypoint and the MOB waypoint will be targeted The view is switched to the Chart View automatically when MOB is activated and an additional info box that shows the lat lon position of the MOB waypoint and the elapsed time since MOB was activated is added to the Chart View It is not possible to re
161. s progress across a given distance and is the speed measurement provided by GPS An alternate Speed Through Water is provided by a speed paddlewheel and is the measurement of the flow past the boat which may vary depending on current speed and direction Speed Over Ground is optimal for navigation because accurate destination times can be derived from this measurement Humminbird products allow for input and display of both speed measurements Time To Go TTG Time To Go is the estimated time required to reach the destination waypoint TTG is calculated using the SOG and DIG See SOG and DIG Track A Track is a series of saved points that define the past path of the boat These Track Points are saved at regular time intervals Tracks are a useful and quick method to see where you ve been and an easy guide to follow to get you back to the starting point Generally all GPS units have a limited number of Track Points that can be saved before the unit runs out of memory and begins erasing the first track points saved Because of this the user can adjust the Track Point Interval menu to increase the amount of time between when points are saved and thus extend the distance covered by a track Tracks can also be permanently saved to memory and re displayed at the user s option Track Line TRK The Track Line is the desired line of travel between two waypoints and represents the most efficient path between the two points because it is a stra
162. s the waypoint grid from the display This menu choice will only appear when a grid has already been applied to a waypoint To Remove a Grid 1 Highlight Remove Grid on the Navigation X Press Menu 2 Use the RIGHT 4 WAY Cursor Control key to remove the grid 19 Waypoint Name Most recently created waypoint Waypoint 8615 gt Waypoint Name allows you to view the waypoints submenu for the most recently created waypoint NOTE You must have pressed the MARK key at least once since you last powered up the Fishing System for this menu choice to appear To view the Waypoint Name Submenu 1 Move the cursor to the desired position and press the MARK key once to save a waypoint 2 Highlight Waypoint Name on the Navigation X Press menu 3 Use the RIGHT 4 Way Cursor Control key to view the Waypoints submenu inane Waypoint Name Submenu The Waypoint Submenu contains the following menu choices Edit allows you to edit the Name Position Latitude and Longitude and select the Icon that will be used to represent the waypoint in the Chart and Combo Views Delete allows you to delete a waypoint from the list of saved waypoints Go To allows you to select a waypoint and start navigation toward that waypoint or add that waypoint to the end of the current route Target allows you to apply a target to a waypoint selected from the list of waypoints Grid allows you to apply a trolling grid to a wa
163. screw has a thread locking compound on the threads to prevent loosening and should not be fully tightened until all adjustments are made installation after high speed testing Headed Pin O Nylon Washer fits over headed pin Stainless Washer fits over screw threads O Screw NOTE The running position of the transducer is now completely adjustable Subsequent adjustment may be necessary to tweak the Adjust the running position of the transducer The transducer mounting bracket allows height and tilt adjustment while the pivot bolt allows angular adjustment These adjustments will help reduce cavitation Initially adjust the transducer as described in the following paragraphs Further adjustment may be necessary to refine the installation after high speed testing Normal Cavitation Cavitation that will cause erratic sonar readings NOTE Your transducer may not look exactly like the transducer shown in the illustrations but it will mount in exactly the same way 1 First adjust the pivot angle of the transducer body so it is parallel with the length of the hull of the boat 2 Fully tighten the two pivot screws using the supplied Allen wrench Access to the pivot screws is provided by the lower holes in the side of the mounting bracket It may be necessary to re tighten the pivot bolt after initial use as the plastic may still be conforming to the pressure from the lock washers 3 Adjust the height of the assembly
164. sonar settings quickly and easily Maximum Depth Menu The Maximum Depth Menu is a Humminbird feature that optimizes performance based on the maximum operational depth set by the user Many Humminbird units can operate across a very broad depth range up to 2500 feet which causes the unit to look up to that full depth under some circumstances Due to the speed of sound in water this can result in less responsiveness because the unit has to wait for a longer period of time to receive the sonar signal When the Maximum Depth menu is set to a lower value the unit only looks up to the setting which increases the responsiveness of the unit This is an important feature for anyone operating in shallower depths Noise Noise is unintentional external sound waves that interfere with the optimal operation of sonar Noise appears as random dots on the display and is caused by a variety of sources Electrical noise from trolling motors bilge pumps VHF radios typically manifests as a consistent dot pattern Electrical noise can be isolated by selectively turning on and off other electrical devices to determine the source Often re routing the power cable or connecting to an alternative power supply second battery can help overcome electrical noise Hydrodynamic noise from propeller and or hull cavitation has a more random appearance and is generally related to boat speed so that faster operation results in more noise Hydrodynamic noise can
165. stem Status for more information about the Accessory Test From the System Status screen see a GPS Diagnostic View by pressing the View key GPS Diagnostic View shows a sky chart and numerical data from the GPS receiver The sky chart shows the location of each visible GPS satellite with its satellite number and a signal strength bar A dark grey bar indicates that the satellite is being used to determine your current position A light gray bar indicates that the satellite is being monitored but is not yet being used See System Status for more information about the GPS Diagnostic View Getting Started Using Your 900 Series Your 900 Series Fishing System user interface is easy to use A combination of keys different views and situation specific customizable menus allows you to control what you see on the color display Refer to the following illustration and see Key Functions Views and The Menu System for more information Screen 4 WAY Cursor Control Key MMC SD Card Slot MENU Key Q 200M Keys VIEW Key Q POWER LIGHT Key EXIT Key D 0 key View Preset Keys Q MARK Key GOTO Key 21 Powering Up the Control Head Turn on your 900 Series control head by pressing the POWER key The Title screen is displayed until the 900 Series begins operation Your 900 Series will begin Normal or Simulator operation depending on the presence or absence of a transducer YVHUMMINEIRD 967c 3D Combo
166. t different depths and different times of the year A thermocline typically appears as a continuous band of many colors moving across the display at the same depth Sonar Color Bar color spectrum indicating low to high sonar intensity returns where red indicates high intensity and white indicates low intensity Bait Ball RTS Real Time Sonar Window Fish ID A fish icon will be shown at the derived position of the fish Six fish icon styles will be used to indicate the primary beam in which the fish was found Left facing fish indicate fish off the port side of the boat while right facing fish indicate fish off the starboard side Each fish icon is available in three different sizes Larger fish icons are used to represent stronger returns Real Time Sonar RTS Window A Real Time Sonar RIS Window appears on the right side of the display in the Sonar View only The RIS Window always updates at the fastest rate possible for depth conditions and shows only the returns from the bottom structure and fish that are within the transducer beam The RTS Window plots the depth and intensity of a sonar return See Sonar Menu RTS Window The Narrow RTS Window indicates the sonar intensity through the use of colors Red indicates a strong return A amp and blue indicates a weak oe return The depth of the sonar return is indicated by the vertical placement of the return on the disp
167. t of easy to use keys that work with various on screen views and menus to give you flexibility and control over your fishing experience Your control head has the following keys e POWER LIGHT key e EXIT key e VIEW key e 4 WAY Cursor Control key e MENU key e VIEW PRESET keys e MARK key e GOTO key e INFO key e ZOOM keys POWER LIGHT Key i Q The POWER LIGHT key is used to turn the 900 Series on and off and also to adjust the backlight and background color of the display Press the POWER LIGHT key to turn the unit on The Title screen is then displayed until the 900 Series begins sonar operation 31 To adjust the backlight or to adjust the display background color press the POWER LIGHT key to access the Light and Background menu Use the 4 WAY Cursor key to select Light or Background and then use the LEFT or RIGHT Cursor key to change the settings Press EXIT to exit the Light and Background menu i Background White Press and hold the POWER LIGHT key for 3 seconds to turn the unit off A message will appear telling you how many seconds there are until shutdown occurs Your 900 Series should always be turned off using the POWER LIGHT key This will ensure that shutdown occurs properly and any menu settings will be saved VIEW Key Press the VIEW key to advance to the next view Repeatedly pressing VIEW cycles through all views available Views can be hidden to optimize th
168. t voltage Accessory Test Screen Depth _ ft SYSTEM STATUS Self Test Screen 26 6 SYSTEM STATUS Temperature CONNECTED WeatherSense CONNECTED CannonLink CONNECTED 2 39 _GPS CONNECTED SmartCast WSL CONNECTED m mPh Speed CONNECTED SPEED mph Press VIEW for Next Screen NOTE The speed accessory will be detected only if the paddlewheel has moved since your 900 Series was powered up 61 GPS Diagnostic View GPS Diagnostic View which is only available when a GPS Receiver is attached to you 900 Series shows a sky chart and numerical data from the GPS receiver The sky chart shows the location of each visible GPS satellite with its satellite number and a signal strength bar A dark grey bar indicates that the satellite is being used to determine your current position A light gray bar indicates that the satellite is being monitored but is not yet being used This view also reports the current position local time and date and other numeric information The current GPS Fix Type is reported as No Fix 2D Fix 3D Fix or Enhanced An Enhanced fix has been augmented using information from WAAS EGNOS or MSAS A 3D or Enhanced Fix is required for navigation HDOP the Horizontal Dilution of Precision is a GPS system parameter which depends on the current satellite configuration HDOP is used to calculate the Estimated Position Error 62 GPS Diagnostic View GPS Diagnostic View Enhanced 1 00 17ft 10
169. talling the GPS Receiver if included e Installing the Temperature Probe Accessory e Testing the complete installation and locking the transducer position NOTE Accessories may require a separate purchase You can visit our website at www humminbird com to order these accessories online or contact our Customer Resource Center at 1 800 633 1468 Control Head Installation You have two choices for mounting your 900 Series control head Gimbal mounting where you use a surface on the boat such as the dash to mount the control head so that it can be tilted up or down or In dash mounting which requires a separate purchase Gimbal Mounting the Control Head If you are gimbal mounting the Humminbird 900 Series you can pre assemble the unit in order to plan the best mounting location Washer Gimbal Knob Gimbal Bracket In addition to the hardware supplied with your control head you will need a powered hand drill and various drill bits various hand tools including a Phillips head screwdriver a socket wrench and a flat head screwdriver a marker or pencil safety glasses and dust mask and marine grade silicone sealant 1 Place the control head into the gimbal bracket Make sure that the Straight side of the gimbal arm is against the back side of the control head 2 Place a 1 25 mm diameter black washer on the gimbal knob and then thread the knob and washer into the housing Tighten the gimbal knob to se
170. tion NOTE See 2D Sonar View for more information about the 2D side of this view 3D 2D Combo View Boat Direction Arrow Fish ID Q 3D Bottom Contour Q Upper Depth Range Q Lower Depth Range Frame Depth Triplog WeatherSense optional purchase O Water Surface Temperature Speed O 20 Sonar View 2D Sonar View 2D Sonar View is a 2 dimensional view that presents a historical log of 2D sonar returns When in 2D Sonar View your unit operates like a typical depthsounder The most recent sonar returns are charted on the right side of the window as new information is received the older information is moved across the display to the left There are however several exceptions The 6 beam 53 degree transducer allows you to search for fish with a much wider area of coverage Only the two center beams provide sonar returns for the bottom contour shown on the display The fish symbols shown in the 2D sonar View are the same as those used in the 3D Sonar View and provide information on the location of the fish relative to the boat see Sonar Menu Tab Fish ID Use the 2D Sonar View for identifying structure and bottom hardness NOTE If the Depth number is flashing it means that the unit is having trouble locating the bottom This usually happens if the water is too deep the transducer is out of the water the boat is moving too fast or for any other reason that the unit cant accurately recei
171. tional 90 days after service has been performed by our factory technicians You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product visit the Product Support section http www humminbird com We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain This Service Policy is valid in the United States only This applies only to Humminbird products returned to our factory in Eufaula Alabama This Service Policy is subject to change without notice 118 Returning Your Unit for Service Before sending your unit in for repair please contact the factory either by phone or by email to obtain a Repair Authorization Number for your unit Please have your product model name and serial number available before calling the factory If you contact the factory by e mail please include your product model name and serial number in the e mail and use Request for Repair Authorization Number for your e mail subject header You should include your Repair Authorization Number in all subsequent communications about your unit For IN WARRANTY service complete the following steps e Obtain a Repair Authorization Number from the Humminbird Customer Resource Center e ag product with your name street address phone number and your assigned Repair Authorization Number e Include a brief written description of the problem
172. trength of the sonar signal on the display and is a very intuitive method of presenting information Traditionally the strongest sonar signals are represented in black and progressively weaker signals are represented in progressively lighter shades of gray Grayscale Inverse Inverse Grayscale is a Humminbird feature that reverses the correlation of sonar signal strength and the shade of gray typically used to represent it The strongest sonar signals are represented by white and progressively weaker signals are represented in progressively darker shades of gray While somewhat counter intultive this method makes the sonar images crisper and has the benefit of enhancing the apparent sensitivity because the weaker signals appear bolder Inverse grayscale works well in very clear water Debris laden water often appears as a lot of clutter on the screen Instant Image Update Instant Image Update is a Humminbird feature that updates all the sonar information on the display when Sensitivity and a variety of sonar settings Bottom View Range etc are modified This differs from the traditional functionality that only updates the new sonar information collected after the setting change Instant Image Update permits more accurate fine tuning of the Glossary display because the user can see the results on the complete sonar graph When combined with the Freeze Frame feature the user can adjust and understand the effects of many different
173. tup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Date Format mm dd yy dd mm yy or yy mm dd Default mm dd yy Date Format Advanced International only 109 Digits Format Digits Format Digits Format allows you to add a tenth decimal place to readouts such as Temperature and Depth The format can be changed to small format large format or no format This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode To change the Digits Format setting 1 Make sure you are in Advanced User Mode then highlight Digits Format on the Setup menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to change the Digits Format setting Small tenths Large tenths No tenths Default Small tenths B ae 4 off b Advanced NMEA Output turns the NMEA output on or off This menu choice is available only when in Advanced User Mode see Setup Menu Tab User Mode The following NMEA sentences are output DPT Depth MTW Water Temperature GLL Lat Lon Position GGA GPS Fix Data RMC Recommended Minimum Specific GNSS Data VTG Course Over Ground and Ground Speed ZDA Time and Date When navigating the following NMEA sentences are also output APB Autopilot Sentence B BWR Bearing and Distance to Waypoint RMB Recommended Minimum Navigation Info To turn NMEA Output on or off 1 Make sure you are in Advanced User Mode then highlight NMEA Output on the
174. umminbird feature that describes the high degree of sonar sensitivity achieved through a combination of transmitter receiver and software algorithms The result of Sonar Echo Enhancement is to display virtually everything in the water that is of interest to the angler including bait fish game fish thermoclines weed beds subtle structure and more Sonar Update Rate Sonar Update Rate is the number of times per second that the transmitter receiver sends and receives sonar signals A very fast sonar update rate collects more information and provides a more detailed image of the bottom fish Glossary and structure Many Humminbird units operate at up to 40 times per second when in single frequency operation Due to the limitation of the speed of sound in water the update rate begins to slow as depth increases to deeper than 50 feet In very shallow water less than 10 feet however update rates as much as 60 times per second can be achieved Speed Speed is the rate at which the boat moves through the water Boat speed can be measured as Speed Over Ground or Speed Through Water Speed Over Ground is provided by GPS and is the measurement of the boats progress across a given distance Speed Through Water is provided by a speed paddlewheel and is the measurement of the flow past the boat which may vary depending on Current speed and direction Speed Through Water is most critical for anglers using downriggers as it impacts the running d
175. und a particular waypoint even if you pass over it multiple times Continuous Navigation Mode allows you to To activate or de activate Continuous Navigation 1 Highlight Continuous Navigation Mode on the Navigation main menu 2 Use the LEFT or RIGHT 4 WAY Cursor Control keys to turn Continuous Navigation Mode On or Off Off On Default Off 94 WO X CA bed Chart 5 fag All MMC SD Onl Hidden Hidden Visible 5m Set Simulation Position Set Map Offset Clear Map Offset Chart Menu Chart Menu Tab Press the MENU key twice to access the Main Menu System and then press the RIGHT Cursor key to select the Chart tab NOTE Menu choices will vary depending on system settings such as whether the unit is set for Advanced User mode ee Detail Level Chart Detail Level Map Borders Map Borders 4 a P Chart Detail Level allows you to select how C Map Borders allows you to display or hide much chart detail you want displayed on the Navigation Views Basic shows map borders A Map Border indicates an area which contains a different map land areas ports obstructions and restricted areas Navigation shows navaids landmarks ferryways and navigation routes in addition to the Basic information Underwater shows depth contours fishing areas underwater wrecks tides and currents in addition to the Basic and Navigation P i information All shows roads buildings railways and other notations in oa RSA p fi
176. ur time period of today s date You can change the date to look at current information before or after the date displayed by pressing the LEFT or RIGHT Cursor key respectively Press the EXIT key to remove the information box and the Bullseye Cursor will be centered over the current station position The Cursor Information Boxes will indicate the distance and bearing to the current station from your present position Navigation Use the 900 Series to establish waypoints at areas of interest and to navigate to those waypoints via a saveable route representing the shortest intended distance between waypoints You can also view and save tracks which represent the actual path of the boat Waypoints Routes and Tracks Waypoints are stored positions that allow you to mark areas of interest or navigation points Your 900 Series can store up to 3000 waypoints Waypoints Routes and Tracks Lepth Course Direction that boat is traveling relative to North Reference TIG Estimate of Trip Time to Destination Waypoint O Speed Over Ground Speed of Boat Q Bearing Direction to Destination Waypoint Waypoint O Relative to North Reference Route QO XTE Cross Track Error Distance of Boat from Route Off Course Alarm Limits Q 07G Distance to Go to Waypoint Map Scale Q 52 Routes link two or more waypoints together to create a path for navigation and are used in trip planning You can link individual waypoints together b
177. urn from a sloping bottom can have the appearance of a softer bottom 122 Sonar Terms Cavitation Cavitation is the effect of air bubbles created as the propeller rotates and the boat moves through the water Chart Speed Chart Speed is a user controllable feature that sets the speed at which sonar information moves across the display A faster setting displays sonar information from more pings and shows more detail but the information moves quickly across the display a slower setting permits viewing of more sonar history but does not display as much detail The best setting is often the user s personal choice Cone Angle The cone angle is the angular measurement of the sonar beam at a specific dB down point i e 10 dB See dB Down Point Customizable Digital Readouts Customizable Digital Readouts is a Humminbird feature that permits the user to select the specific digital information that appears in the main Sonar view i e Speed Temperature Barometric Pressure TripLog etc Dead Zone The dead zone is the area of the sonar beam that receives the sonar signal after the main bottom return Fish and other objects close to the bottom that fall within the dead zone will probably not be visible in the sonar beam Precision sonar beams such as the Humminbird 20 beam have a smaller dead zone than wider sonar beams Decibel A Decibel is the measurement for sound pressure level or intensity of the sonar return See dB D
178. ve continuous data Freeze Frame Pressing any arrow on the 4 WAY Cursor Control key will freeze the screen in the 2D Sonar View and a cursor and cursor dialog box will be displayed on the screen The cursor can be positioned on the display using the 4 WAY Cursor Control key to determine the depth of any sonar return The RIS Window continues to update in Freeze Frame In addition see the effects of menu setting changes with Instant Image Update Pressing EXIT will exit Freeze Frame and the display will start to scroll Freeze Frame is only available in the Sonar View 2D Sonar View C Depth Dist Beari olsosgze glazo g Depth Toog Temperature Speed cursor Depth of Cursor 37 Depth below Cursor Distance to Cursor Bearing to Cursor O RTS Window Q Sonar Color Bar Q Lower Depth Range 2D Zoom View 2D Zoom View increases the displayed resolution to separate sonar returns that are very close together such as those caused by fish suspended close to the bottom or within structure In 2D Zoom View the display is split to show the full range view on the right and the zoomed view on the left The full range view on the right also contains the Zoom Preview Box that shows what part of the full range view is shown in zoom view on the left the Zoom Preview Box tracks the bottom in the full range view As the depth changes the zoomed view updates automatically to display a magnified image of the
179. vironment but it is not waterproof The MMC is removable from Humminbird products and can be used in a PC that is equipped with an appropriate card reader MMC is the same format that many digital cameras use See SD North Magnetic North is the principle reference point of the compass i e North is 000 Magnetic North relies on the earth s magnetic field to align a metal pointer generally towards True North However due to local variations in the earth s magnetic field around the globe the difference between True North and Magnetic North can be greater than 10 See 7rue Worth North True North is the principle reference point of the compass i e North is 000 True North uses the axis of the rotation of the earth as the reference for North and is constant for all points on the earth Most GPS units default to True North as the setting The GPS heading may vary from the boat compass heading because the compass uses Magnetic North Humminbird GPS units provide the option of selecting True or Magnetic readouts by using the North Reference menu See Magnetic North 130 GPS amp Navigation Terms Present Position Present Position is the current location latitude longitude determined by GPS The Present Position is indicated on screen by a directional boat icon if the boat is moving or a round symbol if the boat is stationary Route A Route is series of waypoints linked together in a specific sequence to define a navigat
180. xels Power Output Power output is the amount of sound energy emitted into the water by the sonar transmitter Power output is measured using either RMS Root Mean Square or P I P Peak to Peak measurement systems Either method is acceptable but it is important when comparing power outputs to make sure that the same measurement system is being used for both outputs because P I P numbers are 8 times higher than RMS numbers Greater power output allows the sonar signal to penetrate through weeds and thermoclines reach deeper depths and operate more effectively in noisy environments such as when the boat is running at high speed Pulse Width Pulse Length Pulse Width is the length of time that a sonar sound burst is transmitted into the water Shorter pulse widths provide better target separation but cannot travel to great depths Longer pulse widths provide better depth penetration but result in poorer target separation Humminbird varies pulse width based on depth to optimize both target separation and depth performance See Target Separation Glossary QuadraBeam PLUS QuadraBeam PLUS is a Humminbird sonar configuration that uses four sonar beams for a more detailed bottom image QuadraBeam PLUS uses the DualBeam PLUS configuration for downlooking and also adds two additional beams to look to the left and right The sonar beams pointing to the left and right provide the ability to spot fish and structure over a wide 90
181. y using the GOTO key A route represents your intended navigation and shows the shortest path from each waypoint to the next As you travel a route staying on the route line is the most efficient way to get to your destination although you should always look out for obstacles not shown on the chart Your 900 Series can store up to 50 routes that can each contain up to 50 waypoints Tracks consist of detailed position history and are displayed as a breadcrumb trail of trackpoints The Current Track shows the position history since the unit was powered up maximum of 20 000 trackpoints displayed You can clear the Current Track or save it at any time Your 900 Series can store up to 50 saved tracks each containing 20 000 trackpoints The current track represents your actual path so far Save Edit or Delete a Waypoint Save your current position as a waypoint On any view press the MARK key to save the current position of the boat as a waypoint Save the cursor position as a waypoint On the Chart or Combo view use the Cursor key to designate the position you want to save as a waypoint Then press the MARK key to save the marked position as a waypoint Save a position from the sonar history Use the Cursor key to point to a feature in the sonar history also called the Sonar Saver feature Press the MARK key to create a waypoint at the location where that sonar reading was taken The new waypoint will also record the depth at that l
182. y X Press menu 2 Press the RIGHT 4 Way Cursor key 71 Delete Image optional purchase MMC SD Card Snapshot and Recording View only Ea Delete Image Delete Image allows you to delete a single screen capture image from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are in Snapshot and Recording View and you have selected an image thumbnail To delete an image 1 On the Screen Snapshot View use the UP and DOWN 4 Way Cursor keys to select the image you want to delete 2 Highlight Delete Image on the Snapshot and Recording X Press menu 3 Press the RIGHT 4 Way Cursor key to initiate this procedure 4 A Confirm Dialog box will appear Select Yes to delete the image or No to cancel the operation Delete All Images Delete All Images gt optional purchase MMC SD Card Snapshot and Recording View only Delete All Images allows you to delete all the images at once from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are in Snapshot and Recording View To delete all images 1 From the Snapshot and Recording View highlight Delete All Images on the Snapshot and Recording X Press Menu 2 A confirmation dialog box will ask if you want to delete all images Select Yes to delete or No to change your mind 78 Delete Recording opti
183. you can program the VIEW PRESET keys to display a specific view immediately To program each VIEW PRESET key use the VIEW key to cycle to the view you want to store Press and hold one of the VIEW PRESET keys for several seconds A series of audible chirps will be heard indicating that the view has been programmed to the key You can store up to three views one on each key EXIT Key The EXIT key has multiple functions depending on the situation e f an alarm is sounding pressing EXIT will cancel the alarm e f a menu tab is selected pressing EXIT will exit the menu mode and return to the view e f a menu is active pressing EXIT will return to the previous level in the menu system e Pressing EXIT will cycle through the available views in reverse order e f Freeze Frame is active pressing EXIT will return to a scrolling display e f the Cursor is active pressing EXIT will remove the cursor from the display INFO Key Press the INFO key while in any navigation view to display information about objects that are nearest to an active cursor If the cursor is not active the following menu will be displayed Use the 4 WAY Cursor Control key to select Nearest Port Nearest Tide Station or Nearest Current Station then use the RIGHT Cursor key to a ral display the requested information NOTE The built in UniMap does not contain Port Tide or Current information This information Is on
184. you select a menu item from the X Press Menu the menu will collapse leaving only the menu choice on the screen Use the UP or DOWN Cursor keys to reactivate the X Press Menu 10 va Sensitivity C 2o Upper Range oft Lower Range Auto D Chart Speed 5 Standard X Press Menu NOTE The X Press Menu choices will vary depending on which view is active when you press the MENU key as well as whether you are in Normal or Advanced User Mode Either the Sonar or Navigation X Press Menu will appear depending on the view you are in Main Menu Tabs Less frequently adjusted menus are grouped into the Main Menu System The Main Menu system is organized under main tab menu headings to help you find a specific menu item quickly Main tab headings are Alarms Sonar Navigation Chart Setup Views and Accessories 08 LASS as Depth Alarm Off Fish ID Alarm O off off ff Press the MENU key twice for the Main Menu then use the 4 WAY Cursor LEFT or RIGHT key to select a tab and use the DOWN or UP key to select a specific menu item under that tab then use the LEFT or RIGHT keys again to change a menu setting Press the EXIT key to move quickly to the top of the tab A down arrow at the bottom of a menu means that you can scroll to additional menu choices using the DOWN Cursor key A right or left arrow on a menu choice means that you can use the RIGHT or LEFT Cursor keys to make changes or to see more
185. ypoint selected from the list of waypoints 76 Snapshot and Recording X Press Menu Snapshot and Recording View only O Start Recording OStop Recording The Snapshot and Recording X Press menu provides access to the image management and sonar recording functions Delete All Images Delete Recording Press the MENU key once while in the Snapshot and Recording View to access the Delete All Recordings Snapshot and Recording X Press menu amp Pings Per Second NOTE For more information see Snapshot and utoj Recording View Delete Image gt Playback Speed Stop Playback Snapshot and Recording X Press Menu Start Recording optional purchase MMC SD Card Snapshot and Recording View only OStart Recording gt Start Recording allows you to start sonar recording from the Snapshot and Recording View This menu option is only available when you have an optional purchase MMC SD card installed and you are in Snapshot and Recording View To start sonar recording 1 Highlight Start Recording on the Snapshot and Recording X Press menu and press the RIGHT 4 Way Cursor key to start recording OStop Recording b Stop Recording allows you to stop sonar recording This menu option is only available when you have an optional purchase MMC SD card installed Stop Recording optional purchase MMC SD Card only To stop sonar recording 1 To stop recording highlight Stop Recording from an

Humminbird 967C Fish Finder User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents