Hotpoint SDW 60 Dishwasher User Manual
Contents
1. How to adjust the upper basket The upper basket can be setin high or low position to enable you to organise your dishes effortlessly a i bia Open the rail stop flaps and pull the basket out completely Now place it in high or low position then slide it along the guide rails until the front wheels also go in Now close the rail stop flaps Follow the sequence of actions illustrated in figure F Wh at Can Was h Items not suitable for the dishwasher e Cutlery and tableware made from wood or part wood They may become faded and unsightly in appearance Avoid washing horn handled and bronze cutlery in the machine e Delicate decorative glassware and vases special antique or irreplaceable china the decorative patterns printed on these items will not be dishwasher proof e Plastic objects that are not resistant to hot water Copper and Pewter utensils Aluminium and Sliver objects Some types of glass can become opaque in appearance after they have been washed too many times ina dishwasher e Highly absorbent materials such as sponges and towels should never be placed in a dishwasher fin any doubt check with the manufacturer on items suitability for dishwasher s WARNING Dishes or cutlery soiled with tobacco ash wax lubricating grease or paint should not be put in the dishwasher Ourrecommendation In future only purchase table or kitchenware that has been confirmed dishwasher proof D I2. Economic and fast cycle to be used for slightly dirty dishes Run cycle immediately after use PRE WASH Preliminary wash cycle for dishes while awaiting completion of the load with the dishes from the next meal DELICATES Special cycle to be used for more delicate items which are sensitive to high temperatures Run cycle immediately after use To optimise wash performance and save on energy O dishwasher use the soak cycle to avoid caked on CYCLE DESCRIPTION DETERGENT FOR PRE WASH amp WASH o 279 93 3 24 g tt 20g WASH CYCLE DURATION in minutes Tolerance 10 Pre wash with hot water at 40 C Wash at 65 C 2 cold rinses Hot rinse at 65 C Drying Wash at 55 C Cold rinse Hot rinse at 70 C Drying 120 2 cold pre washes Wash at 45 C Hot rinse at 65 C Drying Short wash at 40 C Hot rinse at 65 C Drying 2 Short cold wash to prevent food from drying onto the dishes Wash at 50 C Rrinse at 45 C Hot rinse at 65 C Drying try yo use the dishwasher with a full wash load If it takes some time to fill your od and build up of bad odours ip ISHWASHER Before Using your Dishwasher 10 Adjusting the water softener Your dishwasher can adjust its salt consumption according to the hard ness of the water in your home This way you can optimise and customise your dishwasher s salt consumption To adjust salt consumption do as follows 1 Unscrew th
3. clip and rubber tube supplied Ensure the drain hose is securely attached to prevent it coming away while the machine is in use and causing a flood ip ISHWASHER INSTRUCTIONS FOR INSTALLING THE DISHWASHER IN FULLY FITTED KITCHENS Your free standing dishwasher can be installed in modern kitchens as follows to stand next to furniture units or other electric household appliances Please read the chapter on Installation in the instruction manual to insert or built in under the one worktop Should it be necessary to remove the top shelf of the dishwasher proceed as follows Unscrew the 2 rear screws and then with a light push forward let it slide out and remove it See fig 1 Discard the polystyrene rectangle QOpen the door and after unscrewing the fixing screws remove the 3 plastic plugs used to hook the shelf on fig 2 Glue on the small soundproofing adhesive spongy strip onto the top crosspiece photo 3 and after tilting the appliance glue on another one undemeath the base photo 4 Straighten up the appliance and adjust the front and back feet by unscrewing them in an anti clockwise direction to raise the dishwasher to the required height Insertihe appliance underneath the worktop fig 5 checking thatthe inlet and outlet pipes do not get bentor squashed please read the instructions provided in the Installation chapter Open the dishwasher door and glue on the two
4. equal sized adhesive spongy strips on the front edge of the appliance cabinet Begin from the top without leaving out any spaces and make sure the strips adhere all along the length of the edge A small part of the spongy strip protruding onto the outside will block any light left between the dishwasher and adjacent cabinets thus improving the soundproofing Warning The dishwasher plug must be within access once the appliance has been builtin in order to allow for maintenance to be carried out safely The structure of your dishwasher makes it impossible to fit it under a hob D ISHWASHER Getting to know your Dishwasher G E E Upper basket J Saltcontainer cap F F Top spray arm K Washing filter G Basket height adjuster H L Detergent and rinse aid J H Lower basket dispenser Bottom spray arm The Controls A ON OFF Button P Cycle select button Press this button to switch the appliance on ON OFF Indicator light This light informs you that the dishwasher is on C Door opening handle Each time this button is pressed one of the cycle indicator lights E will come on in sequence R Start Reset button With Start the wash cycle begins whereas a the settings S Low salt indicator light This light warns you that it is time to add more salt T Low Rinse Aid indicator light This light warns you that it is time to add more rinse aid Use this handle to open the door are c
5. is positioned adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal Make sure that it is not inclined more than 2 degrees If the appliance is level it will help ensure its correct operation Height Adjustment Insert the appliance into the cutout and then adjust the height using the screws located on the front bottom part of the machine Use a screwdriver to turn the screws in the clockwise or anti clockwise direction to increase or decrease the height respectively Cold water connection Connect the cold water supply hose inserting the small filter supplied with the dishwasher and making sure that itis fastened tightly in place see figure 2 If the water hoses are new or have been out of use for an extended period of time let the water run to make sure itis clear and free of impurities before making the connection If this precaution is not taken the water inlet could get blocked causing damage to your dishwasher Drain hose connection WARNING Connect your dishwasher drain hose to pipes which connect to the foul drain system and not to surface water drains IMPORTANT For the correct operation of your dishwasher it is essential to comply with the following information Standpipe Ensure that the hose is not pushed too far down the standpipe Ifthe end of your drain hose is fitted with retaining flaps ensure they are inserted fully
6. lost its effectiveness for example through incorrect storage with the box leftopen If the dishes show signs of streaking staining etc check E the rinse aid dispenser setting is notsettoo high If there are visible traces of rust inside the tank check E the cap off the salt container is securely closed and that the water softner setting is correct E the correctamountof detergent is being used Certain detergents can be more corrosive than others E the tank is made of steel and therefore any rustmarks are due to external elements fragments of rustfrom the tank pipes pots cutlery etc Special products are commercially available to remove such marks Error messages Your dishwasher is equipped with a safety system which is able to detect operating faults These faults are reported by one or two cycle indicator lights E flash ing rapidly Take a note of which lights are flashing turn the appli ance off and call Hotpoint Service for technical assistance Tap off alarm If you have forgotten to tum the wa ter tap on your appliance will re mind you of this by sounding a few short beeps for a few minutes Turn the tap on and your appliance will Start up again after a few minutes Were you to be absent when these beeps are sounded the appliance will be blocked automatically and cycle 4 and 5 indicator lights Fast amp Dry and Prewash cycle will flash rapidly Turn the appliance off at the O
7. the inlet hose and turn on the water supply tap Check there are no deposits of rust inside the water pipe ifthere are allow water to run from the supply tap for a few minutes Disconnecting the dishwasher When disconnecting the dishwasher itis important that tasks are carried out in the correct sequence e switch off atthe mains and remove the plug from the socket e turn off the water supply e disconnect drain and water inlet hose e pull out the dishwasher carefully withdrawing hoses at the same time Moving the appliance Drain water from the dishwasher secure all loose parts Only transport in an upright position not kept upright during transport any water remaining inside may seep into the control module and cause subsequent errors with programme functions 13 ip ISHWASHER Troubleshooting 14 Caution Do not forget that repairs should only be carried out by a qualified specialist Improper repairs can lead to considerable equipment damage as well as danger to the user The dishwasher must first be disconnected from the electricity supply before any repairs or other work can be carried out Switch off at the mains socket and water supply and remove the plug Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself without having to call out a service engineer Not only does this save costs but it also mean
8. K Hotpoint Kitcnen think Instructions for Installation and Use Dishwasher Model SDW 60 To the Installer Before installation fill in the product details on the back cover of this book The information can be found on the rating plate To the User You must read the instructions prior to installing and using the appliance and then retain them for future reference ip ISHWASHER Contents Electrical Connection 3 For Your Safety 4 Installation 5 6 Getting to know your Dishwasher 7 The Controls 7 How to use your Dishwasher 8 Programme Chart 9 Before Using your Dishwasher 10 11 Loading your Dishwasher 12 Care and Cleaning 13 Troubleshooting 14 Information for Test Labs 15 After Sales Service 16 Hotpoint Guarantee 17 Notes 18 19 Key Contacts Back Cover Retention of this Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance If you sell or pass the appliance to someone else or move house and leave it behind make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings If the Book is lost or damaged a copy may be obtained from Merloni Elettrodomestici UK Ltd Morley Way Peterborough PE2 9JB D ISHWASHER Electrical Connection WARNING This appliance must be earthed Fuses Your appliance comes fitted with a plug and a 13A fuse If you need to replace the fuse only tho
9. N OFF button turn on the water tap and wait approximately 20 seconds before turning the ap pliance back on Re select the wash cycle and the appliance will start up again Clogged filter alarm If the appliance is blocked and indicator lights 3 eco and 5 oprewash flash rapidly this means the filter is clogged by large particles of food residue Turn the appliance off clean the filter thoroughly and reposition it in its seat as illustrated on page 13 Then turn it back on Repeat the programming operations and the selected wash cycle will start up again Water load solenoid valve malfunction alarm lf indicator light 4 Fast amp Dry flashes rapidly turn the dishwasher off and back on again after one minute If the alarm persists first turn off the water tap to avoid any flooding and then cut off the electricity supply and call for technical assistance lf after all the checks the appli ance still does not operate or the problem persists call Hotpoint Service see KEY CONTACTS back page and inform them of the type of problem the abbreviation of the model name Mod and the relative num bers S N written on the rating plate located on the inner edge of the door Switch off at the mains socket and remove the plug Turn off the water supply INFORMATION FOR TEST LABS ISHWASHER Load for 9 Standard Settings tests upper rack at position lower basket upper basket 1 6 8 ahpn D
10. SHWASHER Care and Cleaning Unplug the appliance Before carrying out any cleaning or maintenance on the dishwasher always remove the plug from the electricity socket After every wash When the wash cycle has ended always remember to turn off the water supply tap and to leave the appliance door ajar This way moisture and bad odours will not be trapped inside The filter assembly Ifyou want consistent good results from your dishwasher you need to clean the filter assembly e Remove the larger food particles trapped inside the cup C and the semi circular filter A after each wash pull the cup handle upwards to remove them Just rinse them under running water e The entire filter assembly should be cleaned thoroughly once a month cup C semi circular filter A cylindrical filter B Rotate filter B anticlockwise to remove it For cleaning use a non metallic brush Reassemble the filter parts as shown in the figure and reinsert the whole assembly into the dishwasher Position it into its housing and press downwards The dishwasher is not to be used without filters Improper replacement of the filters may re duce the efficiency of the wash and even damage your dishwasher Cleaning the spray arms Food residue may become encrusted onto the spray arms and block the holes where water comes out Check the spray arms regularly and clean them once in a while Cleaning the Wat
11. The cycle will start up from where you interrupted it Cycle end The end of the wash cycle is indi cated by a double beep and the flash ing of the wash cycle indicator light G Open the dishwasher door press the ON OFF button cutting off the electricity supply to the appliance Turn off the water tap Wait a few minutes before unload ing the dishes they are very hot If you wait a little while they dry better due tothe steam Empty the lower rack first There s been a power failure or you opened the dishwasher door The wash cycle stops and then restarts when the electricity comes back on or when you close the door You decide when it starts When you have loaded the dishes you can choose when to start your dishwasher before setting the wash cycle desired Press button D to delay the start of the wash cycle by 12 9 6 or 3 hours Each time you press it you will hear a short beep and the indicator light G corresponding to the selected delay will light up Now you can select the desired wash cycle Press the start button R and after you hear the beep the countdown to the delayed start will begin Once this time is up the indicator light will stop flashing and the wash cycle will begin If you have set a 12 hour delay for example once you have selected the wash cycle the 12 hour indicator light will flash followed by the others in sequence until the set time delay is up A quick look at the indica
12. ad the baskets correctly Check that the spray arms rotate freely Close the door securely After performing all the operations described in the previous para graphs open the appliance door and press ON OFF button A in dicator light B comes on Your ap pliance is now on and awaiting instructions Select the wash cycle Select the wash cycle by pressing button P Each time this button is pressed one of the indicator lights E will come on in sequence se lect the wash cycle most suitable for the type of dishes to wash see Programme Chart Ifthe appliance door is shut press the Start button R and you will hear a beep the cycle will start up within a few seconds The dishwasher informs you Your dishwasher has indicator lights G which light up to indicate the wash cycle phase that is underway Modifying a wash cycle in progress But if you have chosen the wrong cycle not to worry You can modify the wash cycle in progress if it has only just started Keep the RESET button R pressed for about 5 seconds a prolonged beep will sound followed by three short beeps Indicator light G will turn off and at this stage all the settings will have been cancelled You are now free to re set the correct wash cycle You ve left out a dish Well it happens to everyone Inter rupt the wash cycle by pressing the ON OFF button insert the dish you had forgotten and press the ON OFF button again
13. available from our hotline or through our web site Genuine parts and accessories extended warranties and service repairs are all available on our web site at SERVICECENTRE www theservicecentre co uk 16 K Hotpoint Guarantee Satisfaction guaranteed or your money back We give you a unique satisfaction guaranteed promise valid for 90 days after you have purchased your Hotpoint appliance If there is a technical problem simply call Hotpoint Repair service or visit our web site at www theservicecentre co uk and where necessary we will arrange for an engineer to call If the technical problem is not resolved under this guarantee we will replace your machine or if you prefer give you your money back All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free replacement parts for the first 5 years except microwaves selected integrated appliances and cooker hoods which have a one year guarantee provided that they are fitted by a Hotpoint engineer Guarantee terms and conditions Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the following provisions that your appliance Has been installed and used correctly in accordance with this instruction booklet Has been used solely for domestic purposes and is located on domestic premises ie not for commercial or trade use Has been properly connected to a suitable el
14. e very dirty allow them to soak before being washed Tomake iteasier to load your dishes pull the baskets out What goes into the lower basket We recommend you place the most difficult dishes to wash into the lower basket saucepans lids soup dishes and plates a load example is shown in the photo e Serving dishes and large lids place them on the sides of the basket e Saucepans salad bowls must always be placed upside down Very deep dishes place them obliquely thus allowing water to run down them and cleaning them better The cutlery basket Knives and utensils with sharp blades or tips should be positioned with the sharp parts at the bottom Position all cutlery items so that they don ttouch if the basket is the one with side inserts then insert the tea spoons one by one into the slots see figu re A Itis best if you place longer utensils horizontally at the front of the upper basket After loading the dishes remember to check that the spray arms can turn freely without hitting against any dishes 12 What goes into the upper Load examples basket Place delicate and lightweight dishes in the upper basket glasses tea cups and coffee cups saucers and plates shallow salad bowls slightly dirty frying pans and Shallow pans Position lightweight dishes in such as way as to avoid their being moved by the spray of water upper basket upper basket oll g et a
15. e instructions contained in this manual before using the dishwasher Installation must be performed by a qualified technician in compliance with the regulations in force including the prevention and elimination of radio frequency interference The dishwasher is designed for washing and drying dishes an other use shall be considered improper The manufacturer declines all responsibility for uses other than those described above 1 Seperate packaging materials and dispose of safely DO NOT leave discarded packaging material around the home the various 7 DONOT install outdoors not even if the area is covered by a roof it is extremely dangerous to leave it exposed to rain and thunderstorms 2 After removing the packaging 8 If installed on a carpeted or check to make sure your covered floor ensure that the appliance is intact If in doubt Openings on the underside are contact a qualified not obstructed professional 9 Do not touch the heating 3 DO NOT use extension leads element during or straight after and multiple plugs If the awash cycle electricity supply wire is not 10 Ifthe appliance malfunctions long enough then have it turn off the water inlet tap and replaced with one of the correct disconnect the plug from the length and remember that it wall socket Then read the should be free of bends or section entitled dangerous kinks Troubleshooting If you 4 Inthe event of any damage to cannot resolve the
16. e salt container cap 2 There is an arrow on the neck of the container see figure if necessary turn the arrow anti clockwise from the setting to the setting Select the arrow position depending on the water hardness referring to the table Salt Filling the salt container Always use salt which is intended for dishwasher use The salt container is situated underneath the lower basket fill it up as follows 1 Pull out the lower basket completely unscrew and remove the container cap 2 If it is the first time you add the Salt first fill the container up with water you won t have to do this again next time 3 Put the dishwasher funnel on the hole and pour in approximately two kilos of salt Itis normal that some water comes out of the container 4 Screw the cap back in place carefully When to add salt The salt container should be filled up when the low salt indicator light S flashes Your appliance will re mind you to do so for 5 consecu tive wash cycles Water Hardness ol b Salt Autono consu Selector my position nee cycles 2 18 44 1 8 4 4 36 71 45 89 4 5 8 9 cm oe ow oe oe e You don t know how hard the water in your home is Ask the company that supplies water in your area D ISHWASHER Before Using your Dishwasher To open lid A press button B The detergent should be put into the z c The detergent D Adding detergent 3 g
17. ectrical supply voltage as stated on the appliance rating plate Has not been subject to misuse accident modified or repaired by anyone other than one of Our own service engineers a im oO gta Pay Ce ea a A a i a k For pre purchase information on any other Hotpoint product call 08701 50 60 70 or visit www hotpoint co uk ey QH Recycling amp Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise risk of injury to children remove the door plug and cut mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 17 p siwaster NOTES 18 ip ISHWASHER NOTES K Hotpoint Key Contacts After Sales Service Over 1200 trained specialists directly employed by us ensure that you can have complete confidence in both the appliances and services we offer SERVICECENTRE Repair Service and Information Desk UK 08709 066 066 Open 8 to 8 Mon Fri 8 to 6 Sat 10 to 4 Sun amp Bank Holidays www theservicecentre co uk Republic of Ireland 1850 302 200 Note Our operators will require the following information Serial numbe
18. er Inlet Filter Periodically clean the water inlet filter see figure 2 under Installation located on the outlet of the water supply tap After turning off the water tap unscrew the end of the water supply hose remove the filter and clean it carefully under running water Then return the filter to its place and tighten the water supply hose back into position The seals One of the factors that cause unpleasant odours to form inside the dishwasher is food that remains trapped in the seals Periodic cleaning using adamp sponge will prevent this from occurring DO NOT use solvents or abrasives to clean the exterior and rubber parts of your appliance do not use solvents or abrasive cleaning products Use a cloth dampened with lukewarm soapy water only Ifthere are any stains on the surface of the appliance interior use acloth dampened with water and a little white vinegar or a cleaning product specifically made for dishwashers Going away Ifthe dishwasher is not going to be used for some time carry out the following e run a cycle with the dishwasher emply e switch off atthe electrical socket and unplug e turn off the water supply tap disconnect the inlet hose and allow to drain fill the rinse aid dispenser leave the door ajar to preventthe build up of unpleasant odours inside the dishwasher Before using the dishwasher after along break plug in and switch on at the electrical socket Reconnect
19. i roi f eel j i i yig SIB firs 9 EE a I i Mi Gi A YY i LT YL Wi WITE E e ees i Ee mh i zoss wil iq T It Di ter Vol T It Di ter Vol A _ soupe plate 230m e cup 0 201 a e bow i plate Co ovaipianer 856m n saucer taom oo ee een f e e ee bowl Loading the detergent Loading the Rinse Aid The cleaning detergent should be introduced into the two containers The amountof rinse aid used for each cycle can be regulated by turning Comp 2 and Comp 3 see table at the end of the page the dose adjuster F which you will find under lid C There are 6 different settings the normal dosage is setting 5 4 D 9 i rf 4 JUIN lf the cutlery basket is equipped with two removable grids insertthe cutlery one by one into the slots with the handles at the bottom Position them so that they don ttouch j D O E door side Gale Tadeg EN 50242 27 gr 24 Eco 3 IEC DIN _ Ecorextadry 27g 27 o Press the extra dry button if existing K Hotpoint After Sales Service No company is better positioned to offer an after sales service on a Hotpoint appliance than us the manufacturer As part of our commitment to you all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months In addition to this you also have the advantage of free replacement parts for the fir
20. ill disappear when the appliance is used for the first time WARNING The dishwasher must not be connected to the electricity supply while installation is being carried out This appliance should only be connected to a 230 240V AC source via a properly installed earthed socket Use the dishwasher solely in a domestic environment DO NOT stand or place heavy objects on the door when itis open this could damage the door or cause the appliance to tip forward lf your family includes children DO NOT allow children to play with the appliance or tamper with its controls Keep detergents and rinse aids away from children Keep children away from the open door of a dishwasher there could still be some detergent left inside CAUTION The dishwasher meets the requirements set out by the regulations in force concerning safety and electrical equipment Any technical checks should be conducted exclusively by a trained and authorised technician Repairs carried out by unaithorised persons will invalidate the guarantee as well as posing a potential hazard to the user The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions from tampering with even a single component or from the use of non original spare parts ip ISHWASHER For your Safety This manual forms an integral part of the appliance It must always be kept handy for reference Read through all th
21. into the standpipe This will prevent the pipe from jumping out during installation and use DO NOT position the standpipe near an electrical outlet ENSURE that the drain hose is not kinked and it is routed as shown in the diagram The standpipe should have a bore of at least 38mm 1 1 2 It should be installed as shown have a trap fitted and must discharge into the same drain system as your household sink It MUST NOT be connected to a surface water drain Recommended height for 65mm 2 V2 max standpipe 500mm 20 40mm 1 12 min Sink Waste System For under sink drainage Before connecting the drain hose remove any internal restrictions This will prevent a build up of debris which could cause a blockage Remove any restrictions from the waste spigot and ensure that the sealing bung is removed The hose should be routed such that it is raised to a minimum height of 800mm 31 2 a Spigot height 600mm min NOTE Ensure the sink outlet pipe has a minimum diamtere of 32mm AT g a TEE ITTI 1 Untie the end of the GREY drainage hose from the rear of the appliance 2 Reposition the Hooked End Support as required along the GREY drainage hose 3 If fitting an under sink waste disposal unit cut out the membrane bung or blanking plug 4 Attach the GREY drainage hose to the under sink waste disposal unit securely using the
22. leared with Reset D Delayed start select button This button delays the start of the wash cycle you selected by 12 9 6 or 3 hours E Cycle indicator light G This light informs you which S E R cycle you have selected or the one in progress G Cycle phase and delayed start indicator lights Thes indicator lights inform you which cycle phase is underway P a a ing If you have set a delayed start they also indicate the amount of time left until the wash cycle starts Start Reset N Eco Fast amp Dry Prewash Delicate aD Delay 65 C 55 C 45 C 40 C 50 C z OOO O CD Start rogramme O o o o amp om amp CHD Selec 3hr 6hr 9hr 12hr On Off Salt Refill CD intensive Norma Rinse Aid Prewash Wash Rinse Drying Q Technical Characteristics This dishwasher conforms to Technical characteristics thefollowing European Width cm 45 Community Directives Depth cm 60 73 23 EECof Height cm 85 19 02 73 Low Voltage and subsequent Capacity 9 standard place settings modifications e 89 336 EEC of 03 05 89 Electromagnetic Compatibility and M ains water pressure 4 3 psi 145 psi 30KPa 1M Pa 0 3 10 bar Power voltage See data plate subsequent modifications Total absorber power See data plate 97 7 CE Fuse See data plate Labelling ip ISHWASHER How to use your Dishwasher First of all Turn on the water supply tap completely Add the correct amount of detergent Lo
23. more as itimproves their drying The rinse aid container is situated on the inside of the appliance door you should refill it when light D indicates F that itis empty w If your dishwasher is fitted with a low rinse aid indicator light fill the container up when the indicator light flashes or lights up Filling the rinse aid container mae y iy To open the dispenser turn cap C l l anticlockwise Take care when you pour in the rinse aid to avoid it overflowing You can regulate the amount of rinse aid used by the dishwasher move the adjuster F which you will find under lid C Itis normally setto 4 You can choose from six different positions e Use the right amount of detergent see programme chart e Store your detergent and rinse aid in a cool dry place safely away from children If you live in an area particularly prone to very hard water gt 35 f Glist and Hotpoint recommend that you continue to keep your dishwasher salt topped up The amount of rinse aid needs to be increased if the dishes appear dull or you can see circular stains The amount of rinse aid needs to be reduced if the dishes are sticky or you can see white streaks ip ISHWASHER Loading your Dishwasher First of all Before placing dishes in the baskets remove all course food remains This avoids blocking the filter which would reduce the efficiency of the wash lf Saucepans and frying pans ar
24. problem the power cord have it then call Hotpoint Service replaced by a qualified see KEY CONTACTS back technician page 5 The mains plug must be easily accessible after installation 6 Ifthe appliance is not operating properly or if maintenance operations are necessary disconnect the dishwasher from the mains power supply unplug itl The rating plate featuring the technical data serial number and markings is visibly positioned on the inner edge of the door DONOT remove the rating plate The dishwasher is intended for use by adults DO NOT allow children to come near or play with the controls Keep children away from detergents and clear of the dishwasher door when open Keep all packaging material away from children 1 DONOT use solvents such as alcohol or turpentine which may cause an explosion 2 DO NOT load dishes to wash that are soiled with ash wax or paints 3 DONOT lean sit or stand on any part of the dishwasher this could Cause Injury and or damage the appliance 4 DO NOT drink any water residues from inside the dishwasher D ISHWASHER Installation Choose where you want to install your dishwasher you can place it so that its sides or back panel are side by side with furniture or up against the wall The dishwasher is provided with water supply and drain hoses which can be directed towards the left or right to facilitate appropriate installation Levelling Once the appliance
25. r two containers C and D If using a tablet put it in container 24 gr WEY Now you can close the lid press it r S mre a J down until you hear it click 7 T E If itwon t close Check whether there is any __ Ill detergent residue on the edges of see See the dispenser Remove the excess A We recommend Glist 3 in 1 for use in all Hotpoint dishwashers Brilliant cleaning is guaranteed with Glist 3 in 1 Hotpoint only recommends Glist 3 in 1 Dishwasher tablets to give outstanding cleaning and care Itis important to use detergent specially designed for domestic dishwashers Always follow the manufacturers instructions Glist 3 in 1 advanced dishwasher tablets with active enzymes are the ideal way to protect and care for your dishwasher while getting your dishes and glasses sparking clean Softer Water Built in salt action softens water helping to prevent the build up of limescale in the dishwasher and improve the cleaning result Cleaner Dishes With unique active enzymes in the cleaning phase Glist 3 in 1 breaks down even the hard to shift foodstuffs and grease leaving the dishes spotless and the dishwasher clean too Sparkling Results The built in Glist rinse agent ensures the dishes and glasses are free from water marks and smears If you have any questions regarding Glist 3 in 1 please contact the hotline on 0800 216 730 Rinse aid Rinse aid makes dishes sparkle
26. r f Extended Warranties UK 08709 088 088 Open 8 to 8 Mon Sun www theservicecentre co uk Republic of Ireland 1850 502 200 Genuine Parts and Accessories UK 08709 077 077 Open 8 30 to 5 30 Mon Fri amp 9 to 12 Sat www theservicecentre co uk Republic of Ireland 01 842 6836 Merloni Elettrodomestici UK Ltd Morley Way Peterborough PE2 9JB P05 195043091 01
27. s the appliance is available for use again that much sooner The following list of common occurences and their remedies should help you identify the causes of most problems If the dishwasher won t start check E Isthe dishwasher plugged in at the electricity socket and switchedon E sthere a power failure check other appliances E Check the fuse E ls the water supply tap turned on E Isthewaterinlethose connected properly E Is the pressure of the water supply sufficient E Istheinlethose kinked E Is the filter on the water supply hose blocked E Isthedishwasherdoornotclosed properly If water remains inside the dishwasher check E the drain hose is not kinked W the drain syphon is not obstructed E the dishwasher filters are not Clogged If the dishes are not being cleaned properly check E thecorrectamount of detergent hasbeen added E there is regenerating salt in the Salt container E the dishes have been loaded correctly M ihe selected programme is Suitable forthe type of dishes and the degree of soiling E allfilters are clean and positioned correctly E the spray arm nozzles are not obstructed E there is nothing obstructing the rotation of the spray arms If the dishes fail to dry or remain dirty check E there is rinse aid inside the rinse aid container E the rinse aid dispenser setting is correct E the detergent being used is of good quality and has not
28. se rated at 13A and ASTA approved to BS1362 should be used If you lose the fuse cover a replacement may be obtained from your local authorised Service Centre or Electrical company Correct replacement is identified by colour coding or the marking on base of plug WARNING DO NOT use the plug unless the fuse cover is fitted Changing the Plug Cut off and dispose of the supplied plug if it does not fit your socket WARNING To avoida shock hazard DO NOT insert the discarded plug into a socket anywhere else IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE Green Yellow Earth Blue Neutral Brown Live If you change the plug the colour of the wires in the mains lead may not correspond with the terminal markings in the plug which if not coloured could be EARTH E or NEUTRAL N LIVE L Changing the Mains Lead A lead can be ordered from Hotpoint Service UK 08709 066 066 or Republic of Ireland 1850 302 220 If you have damaged the existing lead or require a longer one a charge will be made Itis strongly advised that this work is carried out by a qualified electrician lf the domestic wiring includes a residual current operated circuit breaker ensure that it conforms to the latest regulations Safety Information At the time of delivery All functions of your dishwasher have been thoroughly tested at the factory Asmall number of water marks may have been left as a result they w
29. st 5 years when fitted by a Hotpoint engineer When the 12 months parts and labour guarantee expires we offer the following after sales service options Repair Service and Information Help Desk UK 08709 066066 www theservicecentre co uk Republic of Ireland 1850 302 200 Note Our operators will require the Model number and the Serial number of your appliance Available 364 days a year with a fast effective and value for money service We have the largest white goods repair service in the UK with over 1200 of our own fully trained engineers All repairs include a parts and labour guarantee for 12 months from the date of the repair If you require any information or have any questions about your appliance our operators are on hand with help and advice All this ensures that you will receive the best available after sales service possible Extended Warranties UK 08709 088 088 www theservicecentre co uk Republic of Ireland 1850 502 200 Whether you have just one or a number of Hotpoint appliances in your kitchen we offer two service cover plans to give you total peace of mind Repair Protection Plan FREE service repairs for a single Hotpoint appliance during the period of cover Kitchen Cover FREE service repairs for all your Hotpoint appliances less than 8 years old Genuine Parts and AccessoriesUK 08709 077 077 www theservicecentre co uk Republic of Ireland 01 842 6836 A wide range of genuine parts and accessories are
30. tor lights will keep you informed of the countdown progress at all times Have you changed your mind If you change your mind you can set a shorter time delay press but ton D to select it You need not reset the wash cycle If on the other hand you want to cancel the delay set and you want the cycle to start immediately press button D repeatedly until the cycle starts and indicator light G corresponding to the cycle start phase comes on Cycle phase and delayed start indicator light G 1 Flashing to indicate a delayed start to remind you that you have set a delayed start 2 On litconstantly each light shows which stage of the wash cycle is in progress Would you like to see which settings you have made Atany time when the cycle is under way if you press button P the cycle in progress indicator light will light up for a few seconds For your own safety ensure the door is closed when the dishwasher is not in use ISHWASHER Programme Chart Select the most suitable programme for the type of dishes and how dirty they are To select the wash programme see the chart below CYCLE SELECTION INSTRUCTIONS INTENSIVE Very dirty dishes and pans NOT to be used for delicate items NORMAL Cycle for normally dirty pans and dishes Standard daily cycle ECO Environmentally friendly cycle with low energy consumption levels suitable for normally dirty pans and dishes FAST amp Dry
Download Pdf Manuals
Related Search