Honda Power Equipment 659800 Portable Generator User Manual
Contents
1. 62 Distrib tor s Limited Warranty 64 Emission Control System Warranty 65 TRANSPORTING STORAGE 50 Transporting 2 50 e 51 Storage Procedure aaan 52 TROUBLESHOOTING 54 WIRING DIAGRAM 56 71 72 MEMO The Power of Dreams 31273610 4 82 05000 2006 12 00X31 ZT3 6100 Printed in Japan2. 17 High Altitude 27 Special Requirement 18 INITIAL USE INSTRUCTIONS 57 Adding Engine Oll LLL aaa 57 Adding FUEN 58 70 MAINTENANCE u l 36 Air Cleaner Service 44 AIr WANK 40 Emission Control System Information 38 E gin Qil aaa aa ai 42 Importance of Maintenance 36 Maintenariee Safety 37 Maintenance Schedule 41 Spark Arrester Maintenance 48 Spark Plug a 46 PRE OPERA TION CHECK Lulu aa aaa EEE 28 ENGINE Oil erisin aaeain ea a aaaea NEEE 28 Fuel Recommendations 32 Refu lifd sisipin aN 30 SPECIFICATIONS ai 61 STARTING THE ENGINE 33 STOPPING THE ENGINE uuu ua usus 35 TECHNICAL amp CONSUMER INFORMATION 62 Customer Service Information
3. a 16 DC Receptacle 16 Eco Throttle uuu u aus 15 ENGINE 11 Tank Cap Vent Lever 12 Ground Terminal tt mee sere 14 OIl Alerte SYSTE urusan aaa shuka 14 Output Indicator 13 Overload Indicator Light 13 Parallel Operation Outlets 15 11 CUSTOMER 62 GENERATOR SAFFETY 5 Important Safety Informati n 7 Safety Label Locations U 5 GENERATOR USE 17 ACApplications 19 AC Operation 20 AC Parallel Operation 23 AC Parallel Operation Applications 21 Connections to a Building Electrical System 17 Connecting the battery charging cable optional equipment 24 Operatori 1 5 24 Disconnecting the battery charging Cable 25 Eco Throttle 26 Ground SY SUI
4. OIL FILLER CAP DIPSTICK 6 Reinstall the maintenance cover 57 ADDING FUEL This engine is certified to operate on unleaded gasoline with a pump octane rating of 86 or higher Never use stale or contaminated gasoline or an oil gasoline mixture Avoid getting dirt or water in the fuel tank If the fuel level is low refuel in a well ventilated area with the engine stopped If the engine has been running allow it to cool first Never refuel the engine inside a building where gasoline fumes can reach flames or sparks You may use regular unleaded gasoline containing no more than 10 Ethanol E10 or 5 Methanol by volume In addition Methanol must contain cosolvents and corrosion inhibitors Use of fuels with content of Ethanol or Methanol greater than shown above may cause starting and or performance problems It may also damage metal rubber and plastic parts of the fuel system Engine damage or performance problems that result from using a fuel with percentages of Ethanol or Methanol greater than shown above are not covered under warranty With the engine stopped add fuel to the generator in a well ventilated area AWARNING Gasoline is highly flammable and explosive You can be burned or seriously injured when handling fuel Stop the engine and keep heat sparks and flame away Handle fuel only outdoors Wipe up spills immediately 58 1 Remove the fuel tank cap FUEL TANK CAP 2 Fuel ca
5. e Covers e Spill proof gasoline cans e Battery charging cords e Parallel connection cables Transfer switches kits e Plugs and connectors 63 Distributor s Limited Warranty PRODUCTS COVERED LENGTH OF WARRANTY BY THIS WARRANTY from date of original retail purchase EU series generators Noncommercial Commercial Rental Nonrental Engine 24 months 24 months Generator Electrical and 24 months 12 months Frame Components Parts amp Accessories See your authorized Honda servicing dealer for details To Qualify for this Warranty The product must be purchased in the United States Puerto Rico or the U S Virgin Islands from American Honda or a dealer authorized by American Honda to sell those products This warranty applies to the first retail purchaser and each subsequent owner during the applicable warranty time period What American Honda will Repair or Replace Under Warranty American Honda will repair or replace at its option any part that is proven to be defective in material or workmanship under normal use during the applicable warranty time period Warranty repairs and replacements will be made without charge for parts or labor Anything replaced under warranty becomes the property of American Honda Motor Company Inc All parts replaced under warranty will be considered as part of the original product and any warranty on those parts will expire coincident with the original product
6. s management The Service Manager or General Manager can help Almost all problems are solved in this way If you are dissatisfied with the decision made by the dealership s management contact the Honda Power Equipment Customer Relations Office You can write to American Honda Motor Co Inc Power Equipment Division Customer Relations Office 4900 Marconi Drive Alpharetta Georgia 30005 8847 Or telephone 770 497 6400 8 30 am to 7 00 pm When you write or call please give us this information Model and serial number Name of dealer who sold the generator to you e Name address of dealer who services your generator Date of purchase Your name address and telephone number detailed description of the problem 62 Honda Publications Shop Manual This manual covers complete maintenance and overhaul procedures It is intended to be used by a skilled technician Available through your Honda dealer or through Helm Inc at 1 888 292 5395 or visit www hondapowerequipment com Parts Catalog This manual provides complete illustrated parts lists Available through your Honda dealer Accessories Catalog Your authorized Honda power equipment dealer offers a wide selection of accessories optional equipment to make your generator even more useful Visit www hondapowerequipment com and click on Generators and Welders to see the entire catalog of accessories Especially popular accessories include
7. 49 4 cm 1 65 x 1 42 in 41 8 x 36 0 Compression ratio 8 0 1 Engine speed 5 500 rpm with Eco Throttle switch OFF Cooling system Forced air Ignition system Full transistor Oil capacity 0 26 US qt 0 25 2 Fuel tank capacity 0 55 US gal 2 1 2 Spark plug CR5HSB U16FSR UB DENSO Generator Model EU 1000i Type California type AC type Non California type AN type Rated voltage 120 V Rated frequency 60 Hz AC output Rated current 7 5 Rated output 900 VA Maximum output 1 000 VA DC output Only for charging 12V automotive batteries Maximum charging output 8A Tuneup ITEM SPECIFICATION MAINTENANCE Spark plug gap 0 024 0 028 in 0 60 0 70 mm Valve clearance cold IN 0 08 0 02 mm See your authorized EX 0 11 0 02 mm Honda dealer Other specifications No other adjustments needed Specifications are subject to change without notice 61 TECHNICAL amp CONSUMER INFORMATION Dealer Locator Information To find an authorized Honda Servicing Dealer anywhere in the United States Visit our website www hondapowerequipment com Customer Service Information Servicing dealership personnel are trained professionals They should be able to answer most questions you may have If you encounter a problem that your dealer does not solve to your satisfaction please discuss it with the dealership
8. LIGHT RED gt If the generator is overloaded in excess of 1 000 or if there is a short circuit connected appliance the overload indicator light red will go ON The overload indicator light red will stay ON and after about four seconds current to the connected appliance s will shut off and the output indicator light green will go OFF Stop the engine and investigate the problem Determine if the cause is a short circuit in a connected appliance or an overload Correct the problem and restart the generator Before connecting an appliance to the generator make sure that is in good order and that its electrical rating does not exceed that of the generator Then start the generator and connect the appliance power cord NOTICE When an electric motor is started the overload indicator light red may come on This is normal if the overload indicator light red goes off after about four 4 seconds If the overload indicator light red stays on consult your Honda generator dealer 20 AC PARALLEL OPERATION APPLICATIONS Follow the instructions included with the parallel operation kit Before connecting an appliance or power cord to the generator e Make sure that it is in good working order Faulty appliances power cords can create a potential for electrical shock e If an appliance begins to operate abnormally becomes sluggish stops suddenly t
9. i LINN 45 2 2 u 32018 1 ng g i ONIGNIM M3112X3 if ii L L YOLYJIONI i 815 Tom GVOT83AO 21 3 0 dV Z wo fous 4 a E Fah 220 i NIV I as 1 5 31411934 LUNN ONIGNIM i 613100 i a19v1d3034 503 3V 7 avy 10411090 Fo 329018 13NVd TOWLNOD _ 32018 HOLWHINID 56 INITIAL USE INSTRUCTIONS ADDING ENGINE OIL The generator is shipped WITHOUT OIL in the engine 1 Place the generator on a level surface 2 Loosen the cover screw and remove the maintenance cover MAINTENANCE COVER 3 With the generator in a level position remove the oil filler cap dipstick 4 Add enough SAE 10W 30 API service classification SJ or later or equivalent oil to bring the oil level to the upper limit of the oil filler neck SAE 10W 30 oil is recommended for general use for additional recommendations see page 28 Do not overfill the engine with oil If the engine is overfilled the excess oil may be transferred to the air cleaner housing and air filter 5 Screw in the oil filler cap dipstick securely
10. j Tighten the carburetor drain screw AWARNING Gasoline is highly flammable and explosive You can be burned or seriously injured when handling fuel Keep heat sparks and flame away Handle fuel only outdoors Wipe up spills immediately 2 Change the engine oil See page 42 3 Remove the spark plug and pour about a tablespoon of clean engine oil into the cylinder Crank the engine several revolutions to distribute the oil then reinstall the spark plug 4 Reinstall the spark plug cap on the spark plug securely 5 Reinstall the spark plug maintenance cover 6 Reinstall the left side maintenance cover and tighten the cover screw securely 7 Pull the starter grip slowly until you feel resistance then return the starter grip gently This closes the valves so moisture cannot enter 53 TROUBLESHOOTING When the engine will not start NO Is there fuel in the Refill the fuel tank tank Y YES Is there enough oil Add the recommended in the engine oil YES Is the spark plug in NO Clean readjust the gap good condition and dry the spark plug Replace it if necessary YES If the engine still does not start take the generator to an authorized Honda generator dealer 54 Appliance does not operate Is the output indicator light ON see page 13 YES NO NO Is the overload Take the
11. Clean Valve clearance Check adjust 2 Combustion chamber Clean After every 300 hrs 2 Fuel tank and filter Clean Every year 2 Fuel line Check Every 2 years Replace if necessary 2 1 Service more frequently when used in dusty areas 2 These items should be serviced by your Honda servicing dealer unless the owner has the proper tools and is mechanically proficient See the Honda Shop Manual 3 For commercial use log hours of operation to determine proper maintenance intervals Failure to follow this maintenance schedule could result in non warrantable failures 41 ENGINE OIL CHANGE Drain the used oil while the engine is warm Warm oil drains quickly and completely 1 Turn the engine switch and vent lever to the OFF position to reduce the possibility of fuel leakage 2 Loosen the cover screw and remove the left side maintenance cover See page 28 3 Place a suitable container next to the engine to catch the used oil 4 Remove the oil filler cap dipstick and drain the oil into the container by tipping the engine toward the oil filler neck 5 With the engine a level position fill to the upper limit of the oil filler neck with the recommended oil See page 28 6 Reinstall the oil filler cap dipstick securely 7 Reinstall the left side maintenance cover and tighten the cover screw securely OIL FILLER NECK UPPER LIMIT 42 Wash your hands with soap and water after handling used
12. EU1000i generators for parallel operation see page 21 A Honda approved parallel operation kit optional equipment is required for parallel operation This kit can be purchased from an authorized Honda generator dealer PARALLEL OPERATION OUTLETS 15 DC RECEPTACLE The DC receptacle should ONLY be used for charging 12 volt automotive type batteries The DC charging output is not regulated DC CIRCUIT PROTECTOR The DC circuit protector automatically shuts off the DC battery charging circuit when the DC charging circuit is overloaded when there is a problem with the battery or when the connections between the battery and the generator are improper OFF PUSH ON DC CIRCUIT PROTECTOR DC RECEPTACLE 16 GENERATOR USE CONNECTIONS TO A BUILDING ELECTRICAL SYSTEM Connections for standby power to a building electrical system must be made by a qualified electrician The connection must isolate the generator power from utility power and must comply with all applicable laws and electrical codes AWARNING Improper connections to a building electrical system can allow electrical current from the generator to backfeed into the utility lines Such backfeed may electrocute utility company workers or others who contact the lines during a power outage and the generator may explode burn or cause fires when utility power is restored Consult the utility company or a qualified electrician GROUND S
13. Information 62 Distributor Limited Warranty 64 Emission Control System Warranty 65 INDEX eee rene Seer 70 GENERATOR SAFETY SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury Read them carefully If a label comes off or becomes hard to read contact your Honda generator dealer for a replacement A CAUTION A HOT EXHAUST SYSTEM CAN CAUSE SERIOUS E AVOID CONTACT IF THE ENGINE HAS BEEN RUNNING CALIFORNIA TYPE A CAUTION LLI READ OWNER S MANUAL CAREFULLY BEFORE OPERATION A WARNING GASOLINE 15 HIGHLY FLAMMABLE AND EXPLOSIVE YOU CAN BURNED OR SERIOUSLY INJURED WHEN HANDLING FUEL E STOP THE ENGINE AND KEEP HEAT SPARKS AND FLAME AWAY HANDLE FUEL ONLY OUTDOORS DO NOT FILL THE FUEL TANK ABOVE THE UPPER LIMIT LINE WIPE UP SPILLS IMMEDIATELY B AFTER OPERATION TURN THE ENGINE SWITCH AND FUEL TANK CAP LEVER TO THE OFF POSITION PREVENT FUEL LEAKAGE CARBON MONOXIDE GAS IS TOXIC BREATHING IT CAN CAUSE UNCONSCIOUSNESS AND EVEN KILL YOU E AVOID ANY ENCLOSED AREAS OR ACTIVITIES THAT EXPOSE YOU TO CARBON MONOXIDE CALIFORNIA TYPE A WARNING IMPROPER CONNECTIONS TO A BUILDING CAN ALLOW ELECTRICAL CURRENT BACKFEED INTO UTILITY LINES CREATING AN ELECTROCUTION HAZARD E CONNECTIONS A BUILDIN
14. could hurt you or others Of course it is not practical or possible to warn you about all the hazards associated with operating or maintaining a generator You must use your own good judgement You will find important safety information in a variety of forms including Safety Labels on the generator e Safety Messages preceded by a Safety alert A and one of three signal words DANGER WARNING or CAUTION These signal words mean You WILL be KILLED or SERIOUSLY HURT if DANGER you don t follow instructions A WARNING You be KILLED or SERIOUSLY HURT if you don t follow instructions A CAUTION eu CAN be HURT if you follow instruc ions e Safety Headings such as IMPORTANT SAFETY INFORMATION Safety Section such as GENERATOR SAFETY Instructions how to use this generator correctly and safely This entire book is filled with important safety information please read it carefully CONTENTS ENGINE 11 eer nent 11 Fuel Tank Cap Vent Lever U 12 12 Output Indicator Light 13 Overload Indicat r Light 13 CATER 14 Gro nd Terminal 14 Eco Throttle SSVI ayu u nu au sev 15 Parallel 15 DC 16 DC Circuit Protect
15. has started Make sure that any spilled fuel has been wiped up before starting the generator 8 COMPONENT IDENTIFICATION PARALLEL OPERATION OUTLETS AC RECEPTACLES ECO THROTTLE SWITCH GROUND TERMINAL OIL ALERT INDICATOR LIGHT amp gt l OVERLOAD INDICATOR LIGHT OUTPUT INDICATOR LIGHT DC RECEPTACLE DC CIRCUIT PROTECTOR CHOKE LEVER FUEL TANK CAP VENT LEVER rs FUEL TANK CAP D STARTER GRIP LEFT SIDE MAINTENANCE COVER ENGINE SWITCH SPARK PLUG MAINTENANCE COVER SPARK PLUG AIR CLEANER FRAME SERIAL NUMBER Record the frame serial number for your future reference Refer to this serial number when_ordering parts and when making technical or warranty inquiries See page 62 Frame serial number Date purchased 10 CONTROLS ENGINE SWITCH To start and stop the engine Switch position OFF To stop the engine ON To start and run the engine ENGINE SWITCH OFF STARTER GRIP To start the engine pull the starter grip lightly until you feel resistance then pull briskly in the direction of the arrow as shown below NOTICE Do not allow the starter grip to snap back against the engine Return it gently to prevent damage to the starter STARTER GRIP 11 FUEL TANK CAP VENT LEVER The fuel tank cap is provided with a vent lever to seal the fuel tank The vent lever must be in the ON position for t
16. of this publication may be reproduced without written permission INTRODUCTION Congratulations on your selection of a Honda generator We are certain you will be pleased with your purchase of one of the finest generators on the market We want to help you get the best results from your new generator and to operate it safely This manual contains the information on how to do that please read it carefully As you read this manual you will find information preceded by a symbol That information is intended to help you avoid damage to your generator other property or the environment We suggest you read the warranty policy to fully understand its coverage and your responsibilities of ownership The warranty policy is a separate document that should have been given to you by your dealer When your generator needs scheduled maintenance keep in mind that your Honda servicing dealer is specially trained in servicing Honda generators Your authorized Honda servicing dealer is dedicated to your satisfaction and will be pleased to answer your questions and concerns Best Wishes Honda Motor Co Ltd A FEW WORDS ABOUT SAFETY Your safety and the safety of others are very important And using this generator safely is an important responsibility To help you make informed decisions about safety we have provided operating procedures and other information on labels and in this manual This information alerts you to potential hazards that
17. oil NOTICE Improper disposal of engine oil can be harmful to the environment If you change your own oil please dispose of it properly Put it in a sealed container and take it to a recycling center Do not discard it trash bin dump it on the ground or pour it down a drain 43 AIR CLEANER SERVICE A dirty air cleaner will restrict air flow to the carburetor To prevent carburetor malfunction service the air cleaner regularly Service more frequently when operating the generator in extremely dusty areas AWARNING Using gasoline or flammable solvent to clean the air filter can cause a fire or explosion Use only soapy water or nonflammable solvent NOTICE Operating the engine without an air filter or with a damaged air filter will allow dirt to enter the engine causing rapid engine wear This type of damage is not covered by the Distributor s Limited Warranty 1 Loosen the cover screw and remove COVER SCREW the left side maintenance cover 2 Press the latch tab on the top of the air cleaner case and remove the air cleaner cover 3 Wash the air filter in a solution of household detergent and warm water then rinse thoroughly or wash in nonflammable or high flash point solvent Allow the air filter to dry thoroughly LEFT SIDE MAINTENANCE COVER 4 Soak the air filter in clean engine oil and squeeze out the excess oil The engine will smoke during initial startup if too much oi
18. operation disconnect the parallel operation kit after stopping the engines if you do not wish to resume parallel operation 35 MAINTENANCE THE IMPORTANCE OF MAINTENANCE Good maintenance is essential for safe economical and trouble free operation It will also help reduce air pollution AWARNING Improper maintenance or failure to correct a problem before operation can cause a malfunction in which you can be seriously hurt or killed Always follow the inspection and maintenance recommendations and schedules in this owner s manual To help you properly care for your generator the following pages include a maintenance schedule routine inspection procedures and simple maintenance procedures using basic hand tools Other service tasks that are more difficult or require special tools are best handled by professionals and are normally performed by a Honda technician or other qualified mechanic The maintenance schedule applies to normal operating conditions If you operate your generator under severe conditions such as sustained high load or high temperature operation or use it in unusually wet or dusty conditions consult your servicing dealer for recommendations applicable to your individual needs and use Remember that your servicing dealer knows your generator best and is fully equipped to maintain and repair it To ensure the best quality and reliability use only new genuine Honda parts or their equivalents for
19. repair or replacement Maintenance replacement or repair of the emission control devices and systems may be performed by any engine repair establishment or individual using parts that are certified to EPA standards 36 MAINTENANCE SAFETY Some of the most important safety precautions follow However we cannot warn you of every conceivable hazard that can arise in performing maintenance Only you can decide whether or not you should perform a given task AWARNING Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed Always follow the procedures and precautions in the owner s manual Safety Precautions Make sure the engine is off before you begin any maintenance repairs This will eliminate several potential hazards Carbon monoxide poisoning from engine exhaust Be sure there is adequate ventilation whenever you operate the engine Burns from hot parts Let the engine and exhaust system cool before touching Injury from moving parts Do not run the engine unless instructed to do so Read the instructions before you begin and make sure you have the tools and skills required reduce the possibility of fire or explosion be careful when working around gasoline Use only a nonflammable solvent not gasoline to clean parts Keep cigarettes sparks and flames away from all fuel related parts 37 EMISSION CONTROL SYSTEM I
20. that are on the warranted parts list are warranted up to their required replacement interval only Honda is also liable for damages to other engine components caused by a failure of any warranted part during the warranty period Only Honda approved replacement parts may be used in the performance of any warranty repairs and must be provided without charge to the owner The use of replacement parts not equivalent to the original parts may impair the effectiveness of your engine emission control system If such a replacement part is used in the repair or maintenance of your engine and an authorized Honda dealer determines it is defective or causes a failure of a warranted part your claim for repair of your engine may be denied If the part in question is not related to the reason your engine requires repair your claim will not be denied 67 To Obtain Warranty Service You must take your Honda Power Equipment engine or the product on which it is installed along with your sales registration card or other proof of original purchase date at your expense to any Honda Power Equipment dealer who is authorized by Honda to sell and service that Honda product during his normal business hours Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used If you are unable to obtain warranty service or are dissatisfied with the warranty s
21. the requirements of the California Air Resources Board The bar graph is intended to provide you our customer the ability to compare the emissions performance of available engines The lower the Air Index the less pollution The durability description is intended to provide you with information relating to the engine s emission durability period The descriptive term indicates the useful life period for the engine s emission control system See your Emission Control System Warranty for additional information Descriptive Term Applicable to Emission Durability Period Moderate 50 hours 0 80 cc inclusive 125 hours greater than 80 cc Intermediate 125 hours 0 80 cc inclusive 250 hours greater than 80 cc Extended 300 hours 0 80 cc inclusive 500 hours greater than 80 cc 1 000 hours 225 cc and greater The Air Index Information hang tag must remain on the generator until itis sold Remove the hang tag before operating the generator 40 MAINTENANCE SCHEDULE REGULAR SERVICE PERIOD 3 First Every Every Every ITEM Before month 3 months 6 months 2 years Perform at every indicated month each or or or or or operating hour interval use 10 hrs 50hrs 100hrs 300 hrs whichever comes first Engine oil Check level Air cleaner Check Clean 1 Spark plug Check adjust Replace Spark arrester
22. the spark arrester screen 4 Inspect the screen for breaks or tears and replace it if necessary 5 Check the muffler gasket replace if damaged Reinstall the muffler gasket the spark arrester the muffler and the muffler protector in the reverse order of removal 49 TRANSPORTING STORAGE TRANSPORTING NOTICE Do not lay the generator on its side when moving storing or operating it Oil or fuel may leak and damage the engine or your property If the generator has been used allow it cool for at least 15 minutes before loading the generator on the transport vehicle A hot engine and exhaust system can burn you and can ignite some material To prevent fuel spillage when transporting the generator should be secured upright in its normal operating position with the engine switch OFF and the fuel tank cap vent lever turned fully counterclockwise to the OFF position Take care not to drop or strike the generator when transporting Do not place heavy objects on the generator 50 STORAGE Before storing the unit for an extended period Be sure the storage area is free of excessive humidity and dust 2 Service according to the table below STORAGE TIME RECOMMENDED SERVICE PROCEDURE TO PREVENT HARD STARTING Less than 1 month No preparation required 1 to 2 months Fill with fresh gasoline and add gasoline stabilizer Run the engine for 10 minutes to use up the non treate
23. warranty To Obtain Warranty Service You must take the Honda generator and proof of original retail purchase date at your expense to any Honda Power Equipment dealer in the United States Puerto Rico or the U S Virgin Islands who is authorized to service that product during the dealer s normal business hours If you are unable to obtain warranty service or are dissatisfied with the warranty service you receive take the following steps First contact the owner of the dealership involved normally this should resolve the problem However if you should require further assistance write or call the Power Equipment Customer_Relations Department of American Honda Motor Co Inc Refer to 62 for contact information 64 Exclusions This warranty does not extend to parts affected or damaged by accident and or collision normal wear fuel contamination use in an application for which the product was not designed or any other misuse neglect incorporation or use of unsuitable attachments or parts unauthorized alteration or any causes other than defects in material or workmanship of the product Disclaimer of Consequential Damage and Limitation of Implied Warranties American Honda disclaims any responsibility for loss of time or use of the product transportation commercial loss or any other incidental or consequential damage Any implied warranties are limited to the duration of this written limited warranty Some states
24. ALLEL OPERATION 1 Connect the parallel operation kit between the two EU1000i generators following the instructions supplied with the kit PARALLEL OPERATION KIT optional equipment 2 Start the generators sure the output indicator lights green come 5 page 33 3 Plug in the appliance following the instructions provided with the parallel operation kit Most motorized appliances require more than their rated wattage for startup If the generators are overloaded or if there is a short circuit in a connected appliance the overload indicator lights red will go ON The overload indicator lights red will stay ON and after about four seconds current to the connected appliance s will shut off and the output indicator lights green will go OFF Stop the engines and investigate the problem 23 DC OPERATION The DC receptacle should ONLY be used for charging 12 volt automotive type batteries The DC charging output is not regulated When using the DC output turn the Eco Throttle switch to the OFF position Connecting the battery charging cable optional equipment 1 Before connecting the battery charging cable to a battery that is installed in a vehicle disconnect the vehicle battery ground cable from the negative battery terminal AWARNING The battery gives off explosive gases keep sparks flames and cigarettes away Provide adequate ventilation when charging or using batterie
25. G MUST ISOLATE GENERATOR POWER FROM UTILITY POWER AND COMPLY WITH ALL APPLICABLE LAWS AND ELECTRICAL CODES THE GENERATOR IS A POTENTIAL SOURCE OF ELECTRICAL SHOCK IF NOT KEPT DRY E DO NOT EXPOSE THE GENERATOR TO MOISTURE RAIN OR SNOW E DO NOT OPERATE THE GENERATOR WITH WET HANDS NON CALIFORNIA TYPE AWARNING GASOLINE IS HIGHLY FLAMMABLE AND EXPLOSIVE YOU COULD BURNED OR SERIOUSLY INJURED IF THE GASOLINE 15 IGNITED STOP THE ENGINE AND KEEP HEAT SPARKS AND FLAME AWAY E HANDLE FUEL ONLY OUTDOORS H 00 NOT FILL THE FUEL TANK ABOVE THE UPPER LIMIT LINE N WIPE UP SPILLS IMMEDIATELY AFTER OPERATION TURN THE ENGINE SWITCH AND FUEL TANK CAP LEVER TO THE OFF POSITION PREVENT FUEL LEAKAGE EXHAUST CONTAINS POISONOUS CARBON MONOXIDE GAS THAT CAN BUILD UP DANGEROUS LEVELS IN CLOSED AREAS BREATHING CARBON MONOXIDE CAN CAUSE UNCONSCIOUSNESS OR DEATH NEVER RUN THE GENERATOR IN A CLOSED OR EVEN PARTLY CLOSED AREA WHERE PEOPLE BE PRESENT AWARNING IMPROPER CONNECTIONS TO A BUILDING CAN ALLOW ELECTRICAL CURRENT BACKFEED INTO UTILITY LINES CREATING ELECTROCUTION HAZARD E CONNECTIONS TO A BUILDING MUST ISOLATE GENERATOR POWER FROM UTILITY POWER AND COMPLY WITH ALL APPLICABLE LAWS AND ELECTRICAL CODES GENERATOR 15 A POTENTIAL SOURCE OF ELECTRICAL SHOCK F NOT KEPT DRY HDO NOT EXPOSE THE GENERATOR MOISTURE RAIN OR SNOW EDO NOT OPERATE THE GENERATOR
26. NFORMATION Source of Emissions The combustion process produces carbon monoxide oxides of nitrogen and hydrocarbons Control of hydrocarbons and oxides of nitrogen are very important because under certain conditions they react to form photochemical smog when subjected to sunlight Carbon monoxide does not react in the same way but it is toxic Honda utilizes appropriate air fuel ratios and other emissions control systems to reduce the emissions of carbon monoxide oxides of nitrogen and hydrocarbons The U S and California Clean Air Acts EPA and California regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emission control systems The following instructions and procedures must be followed in order to keep the emissions from your Honda engine within the emission standards Tampering and Altering Tampering with or altering the emission control system may increase emissions beyond the legal limit Among those acts that constitute tampering are e Removal or alteration of any part of the intake fuel or exhaust systems e Altering or defeating the governor linkage or speed adjusting mechanism to cause the engine to operate outside its design parameters 38 Problems That May Affect Emissions If you are aware of any of the following symptoms have your engine inspected and repaired by your servicing dealer Hard starting or stalling after starting e R
27. Owner Manual GENERATOR 1000 Click here to save this 9 manual to your computer Bs See 57 for Initial Use Instructions 2001 2006 Honda Motor Co Ltd All Rights Reserved WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm AWARNING Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in closed areas Breathing carbon monoxide can cause unconsciousness or death Never run the generator in a closed or even partially closed area where people may be present AWARNING The generator is a potential source of electrical shock if misused Do not expose the generator to moisture rain or snow Do not let the generator get wet and do not operate it with wet hands Keep this owner s manual handy so you can refer to it at any time This owner s manual is considered a permanent part of the generator and should remain with the generator if resold The information and specifications included in this publication were in effect at the time of approval for printing Honda Motor Co Ltd reserves the right however to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever No part
28. STEM With the switch in the ON position engine speed is automatically lowered when loads are reduced turned OFF or disconnected When appliances are turned ON or reconnected the engine returns to the proper speed to power the electrical load In the OFF position the EcoThrottle system does not operate Appliances with large start up power demands may not allow the engine to reach normal operating rom when they are connected to the generator Turn the EcoThrottle to the OFF position and connect the appliance to the generator If the engine still will not reach normal operating speed check that the appliance does not exceed the rated load capacity of the generator If high electrical loads are connected simultaneously turn the EcoThrottle switch to the OFF position to reduce voltage changes The EcoThrottle system is not effective for use with appliances that require only momentary power If the tool or appliance will be turned ON and OFF quickly the EcoThrottle switch should be in the OFF position When using the DC output turn the EcoThrottle switch to the OFF position ECOTHROTTLE SWITCH 26 HIGH ALTITUDE OPERATION At high altitude the standard carburetor air fuel mixture will be too rich Performance will decrease and fuel consumption will increase A very rich mixture will also foul the spark plug and cause hard starting Operation at an altitude that differs from that at which this engine w
29. WITH WET HANDS 5 MANUAL CAREFULLY BEFORE OPERATION IMPORTANT SAFETY INFORMATION Honda generators are designed to give safe and dependable service if operated according to instructions Read and understand this owner s manual before operating your generator You can help prevent accidents by being familiar with your generator s controls and by observing safe operating procedures Operator Responsibility e Know how to stop the generator quickly in case of emergency Understand the use of all generator controls output receptacles and connections Be sure that anyone who operates the generator receives proper instruction Do not let children operate the generator without parental supervision Carbon Monoxide Hazards e Exhaust contains poisonous carbon monoxide a colorless odorless gas Breathing carbon monoxide can cause loss of consciousness and may lead to death If you run the generator an area that is confined or even partially enclosed area the air you breathe could contain a dangerous amount of exhaust gas e Never run your generator inside a garage house or near open windows or doors Electric Shock Hazards e generator produces enough electric power to cause a serious shock or electrocution if misused e Using a generator or electrical appliance in wet conditions such as rain or Snow or near a pool or sprinkler system or when your hands are wet could r
30. YSTEM Honda portable generators have a system ground that connects generator frame components to the ground terminals in the AC output receptacles The system ground is not connected to the AC neutral wire If the generator is tested by a receptacle tester it will not show the same ground circuit condition as for home receptacle 17 SPECIAL REQUIREMENTS NOTICE Keep all cooling holes open and clear of debris mud water etc Cooling holes are located on the side panel the contro panel and the bottom of the generator If the cooling holes are blocked the generator may overheat and damage the engine inverter or windings NOTICE Do not lay the generator on its side when moving storing or operating it Oil may leak and damage the engine or your property There may be Federal or State Occupational Safety and Health Administration OSHA regulations local codes or ordinances that apply to the intended use of the generator Please consult a qualified electrician electrical inspector or the local agency having jurisdiction In some areas generators are required to be registered with local utility companies elf the generator is used at a construction site there may be additional regulations that must be observed 18 AC APPLICATIONS Before connecting an appliance or power cord to the generator e Make sure that it is in good working order Faulty appliances power cords can create a
31. as certified for extended periods of time may increase emissions High altitude performance can be improved by specific modifications to the carburetor If you always operate your generator at altitudes above 5 000 feet 1 500 meters have your servicing dealer perform this carburetor modification This engine when operated at high altitude with the carburetor modifications for high altitude use will meet each emission standard throughout its useful life Even with carburetor modification engine horsepower will decrease about 3 5 for each 1 000 foot 300 meter increase in altitude The ef fect of altitude on horsepower will be greater than this if no carburetor modification is made NOTICE When the carburetor has been modified for high altitude operation the air fuel mixture will be too lean for low altitude use Operation at altitudes below 5 000 feet 1 500 meters with a modified carburetor may cause the engine to overheat and result in serious engine damage For use at low altitudes have your servicing dealer return the carburetor to original factory specifications 27 PRE OPERATION CHECK ENGINE OIL Check the oil level BEFORE EACH USE with the generator on a level surface and the engine stopped Use 4 stroke motor oil that meets or exceeds the requirements for API service classification SJ or later or equivalent Always check the API SERVICE label on the oil container to be sure it includes the lett
32. d gasoline 2 to 6 months Fill with fresh gasoline and add gasoline stabilizer Run the engine for 10 minutes to 6 months or more use up the non treated gasoline Or drain the gasoline 52 Drain the gasolinel page 52 Remove the spark plug Put a tablespoon of engine oil into the cylinder Turn the engine slowly with the starter grip to distribute the oil Reinstall the spark plug Change the engine oil After removal from storage fill with fresh gasoline before starting Use gasoline stabilizers that are formulated to extend storage life Follow the instructions included with the gasoline stabilizer Contact your authorized Honda generator dealer for gasoline stabilizer recommendations 51 Storage Procedure 1 Drain the gasoline a Unscrew the fuel tank cap remove the debris screen and empty the fuel tank into an approved gasoline container using a commercially available hand siphon Reinstall the debris screen and the fuel tank cap b Loosen the cover screw and remove the left side maintenance cover c Loosen the carburetor drain screw d Drain the gasoline from the carburetor into a suitable container Remove the spark plug maintenance cover f Remove the spark plug cap g Turn the engine switch to the ON position h Pull the starter grip to 4 times to drain the gasoline from the fuel pump into a suitable container i Turn the engine switch to the OFF position
33. do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions and limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Emission Control System Warranty Your new Honda Power Equipment engine complies with the U S EPA Environment Canada and State of California emission regulations American Honda Motor Co Inc provides the emission warranty coverage for engines in the United States and its territories Honda Canada Inc provides the emission warranty for engines in the 13 provinces and territories of Canada In the remainder of this Emission Control System Warranty American Honda Motor Company Inc and Honda Canada Inc will be referred to as Honda Your Warranty Rights And Obligations California The California Air Resources Board and Honda are pleased to explain the emission control system warranty on your Honda Power Equipment engine In California new spark ignited small off road equipment engines must be designed built and equipped to meet the State s stringent anti smog standards 65 Other States U S territories and Canada In other areas of the United States and in Canada your engine must be designed built and equipped to meet the U S EPA and Environment Canada emission standards for spark ignited engines at or bel
34. er SJ or later or equivalent SAE VISCOSITY GRADES 20 0 20 40 60 80 100 4 30 20 10 0 10 20 30 40 C AMBIENT TEMPERATURE SAE 10W 30 is recommended for general all temperature use Other viscosities shown in the chart may be used when the average temperature in your area is within the indicated range 1 Place the generator on a level surface 2 Loosen the cover screw and remove the left side maintenance cover COVER SCREW LEFT SIDE MAINTENANCE COVER 28 3 Remove the oil filler cap and wipe the dipstick clean 4 Check the oil level by inserting the dipstick into the filler neck without screwing itin 5 If the level is low fill to the upper limit of the oil filler neck with the recommended oil 6 Reinstall the left side maintenance cover and tighten the cover screw securely DIPSTICK UPPER LIMIT OIL FILLER CAP 29 REFUELING With the engine stopped remove the fuel tank cap and check the fuel level Refill the fuel tank if the fuel level is low Refuel carefully to avoid spilling fuel Do not fill above the upper limit mark After refueling tighten the fuel tank cap securely AWARNING Gasoline is highly flammable and explosive You can be burned or seriously injured when handling fuel Stop the engine and keep heat sparks and flame away Handle fuel only outdoors Wipe up spills immediately NOTICE Fuel can damage paint and plastic Be careful not t
35. ervice you received contact the owner of the dealership involved Normally this should resolve your problem However if you require further assistance write or call the Honda Power Equipment Customer Relations Department your region Exclusions Failures other than those resulting from defects in material or workmanship are not covered by this warranty This warranty does not extend to emission control systems or parts which are affected or damaged by owner abuse neglect improper maintenance misuse misfueling improper storage accident and or collision the incorporation of or any use of any add on or modified parts unsuitable attachments or the unauthorized alteration of any part This warranty does not cover replacement of expendable maitenance items made in connection with required maintenance services after the item s first scheduled replacement as listed in the maintenance section of the product owner s manual such as spark plugs and filters 68 Disclaimer of Consequential Damage and Limitation of Implied Warranties American Honda Motor Co Inc and Honda Canada Inc disclaim any responsibility for incidental or consequential damages such as loss of time or the use of the power equipment or any commercial loss due to the failure of the equipment and any implied warranties are limited to the duration of this written warranty This warranty is applicable only where the California U S EPA or environment Canada emi
36. esult in electrocution Keep the generator dry e If the generator is stored outdoors unprotected from the weather check all of the electrical components on the control panel before each use Moisture or ice can cause a malfunction or short circuit in electrical components which could result in electrocution e Do not connect to a building electrical system unless an isolation switch has been installed by a qualified electrician e Use only a Honda approved parallel operation cables kit optional equipment when connecting two EU1000i generators for parallel operation e Never connect different generator models and types Fire and Burn Hazards The exhaust system gets hot enough to ignite some materials Keep the generator at least 3 feet 1 meter away from buildings and other equipment during operation not enclose the generator in any structure Keep flammable materials away from the generator muffler becomes very hot during operation and remains hot for a while after stopping the engine Be careful not to touch the muffler while it is hot Let the engine cool before storing the generator indoors e Gasoline is extremely flammable and is explosive under certain conditions Do not smoke or allow flames or sparks where the generator is refueled or where gasoline is stored Refuel in a well ventilated area with the engine stopped e Fuel vapors are extremely flammable and may ignite after the engine
37. generator to an indicator light ON authorized Honda generator dealer YES DEFECTS Check the electrical Take the generator to an pliance or equipment for authorized Honda generator any defects dealer Replace the electrical DEFECTS pliance or equipment the electrical ap pliance or equipment to an electrical shop for repair Stop and restart the engine No electricity at the DC receptacle Is the DC circuit protector DC circuit protector on on x YES Take the generator to an authorized Honda generator dealer Y 55 802 80102 T T 7 T 39018 3NI9N3 WIRING DIAGRAMI 8 HOLVHIN39 HO LWS 4 9 3399 5 I qNnou9 ond 38104 31 91719 41 3018 18 45 110 at TI w I I NOILINSI 311108H1 9 39018 JAY gt 5 lt lt HOLIMS jj 222 1 9 1
38. he engine to run When the engine is not in use leave the vent lever in the OFF position to reduce the possibility of fuel leakage FUEL TANK CAP VENT LEVER CHOKE LEVER The choke is used to provide proper starting mixture when the engine is cold It can be opened and closed by operating the choke lever manually Move the choke lever to the CLOSED position to enrich the mixture for cold starting CHOKE LEVER CLOSED 12 OUTPUT INDICATOR LIGHT The output indicator light green is illuminated when the generator is Operating normally It indicates that the generator is producing electrical power at the receptacles OUTPUT INDICATOR LIGHT GREEN OVERLOAD INDICATOR LIGHT If the generator is overloaded in excess of 1 000 VA or if there is a short circuit connected appliance the overload indicator light red will go ON The overload indicator light red will stay ON and after about four seconds current to the connected appliance s will shut off and the output indicator light green will go OFF OVERLOAD INDICATOR LIGHT RED 13 OIL ALERT SYSTEM The Oil Alert system is designed to prevent engine damage caused by an insufficient amount of oil in the crankcase Before the oil level in the crankcase can fall below a safe limit the Oil Alert indicator light comes on and the Oil Alert system automatically will stop the engine the engine switch will remain in the ON po
39. l is left in the air filter AIR CLEANER COVER LOWER TAB 44 5 Remove the rubber air guide from AIR CLEANER the air cleaner case CASE Clean the air guide and the air cleaner case with a moist rag then reinstall the air guide 6 Reinstall the air filter 7 sure that the rubber seal is set in the groove of the air cleaner cover 8 Reinstall the air cleaner cover by inserting the lower tab and the latch tab 9 Reinstall the left side maintenance cover and tighten the cover screw securely RUBBER SEAL 45 SPARK PLUG SERVICE In order to service the spark plug you will need a spark plug wrench commercially available Recommended spark plugs CR5HSB NGK U16FSR UB DENSO To ensure proper engine operation the spark plug must be properly gapped and free of deposits NOTICE An incorrect spark plug can cause engine damage If the engine has been running allow it to cool before servicing the Spark plug 1 Remove the spark plug maintenance cover a SPARK PLUG BAY TRE 2 Remove the spark plug cap SPARK PLUG CAP 3 Clean any dirt from around the spark plug base 4 Use spark plug wrench to remove the spark plug PLUG WRENCH 46 5 Visually inspect the spark plug Replace it if the electrodes are worn or if the insulator is cracked chipped or fouled 6 Measure the spark plug electrode gap with a wire type feeler gauge C
40. o spill fuel when filling your fuel tank Damage caused by spilled fuel is not covered under warranty 30 FUEL TANK CAP UPPER LIMIT MARK 22 After refueling tighten the fuel cap srcurely 31 FUEL RECOMMENDATIONS This engine is certified to operate on regular unleaded gasoline with a pump octane rating of 86 or higher Never use stale or contaminated gasoline or an oil gasoline mixture Avoid getting dirt or water in the fuel tank You may use regular unleaded gasoline containing no more than 10 Ethanol E10 or 5 Methanol by volume In addition Methanol must contain cosolvents and corrosion inhibitors Use of fuels with content of Ethanol or Methanol greater than shown above may cause starting and or performance problems It may also damage metal rubber and plastic parts of the fuel system Engine damage or performance problems that result from using a fuel with percentages of Ethanol or Methanol greater than shown above are not covered under warranty 32 STARTING THE ENGINE STARTING THE ENGINE For your safety avoid starting or operating the generator in an enclosed area such as a garage Your generator s exhaust contains poisonous carbon monoxide gas that can collect rapidly in an enclosed area and cause illness or death AWARNING Carbon monoxide gas is toxic Breathing it can cause unconsciousness and even kill you Avoid any enclosed areas partially enclosed areas or ac
41. or 2 renee oe meee ere Oe arene eres 16 Connections to a Building Electrical System 17 GI SV SRI awas paimi 17 Special Requirements 18 AC ApplicationS 19 u u 20 AC Parallel Operation Applications 21 AC Parallel Operator 23 24 Eco Throttle 2 er 26 gh Altit Engine 28 PTS UN deco eee teas 30 Fuel Recommendations 32 MAINTENANCE The Importance of Maintenance 36 Safety 37 Emission Control System Information 38 40 Maintenance Schedule 41 Engine uu uu uum uu sasa 42 Air Cleaner Service nus 44 INITIALUSE INSTRUCTIONS cececeayececrecncuptusceenstdunteapspenadeaure 57 Adding Engine Olli 57 Adding ttt ae cee 58 Customer Service
42. orrect the gap if necessary by carefully bending the side electrode The gap should be 0 024 0 028 in 0 60 0 70 mm 0 024 0 028 0 60 0 70 mm SEALING WASHER 7 Check that the spark plug sealing washer is in good condition and thread the spark plug in by hand to prevent cross threading 8 After the spark plug is seated tighten with a spark plug wrench to compress the washer If installing a new spark plug tighten 1 2 turn after the spark plug seats to compress the washer If reinstalling a used spark plug tighten 1 8 1 4 turn after the spark plug seats to compress the washer NOTICE A loose spark plug can overheat and damage the engine Overtightening the spark plug can damage the thread s in the cylinder head 9 Reinstall the spark plug cap on the spark plug securely 10 Reinstall the spark plug maintenance cover 47 SPARK ARRESTER MAINTENANCE If the generator has been running the muffler will be very hot Allow it to cool before proceeding The spark arrester must be serviced every 100 hours to maintain its efficiency Clean the spark arrester as follows 1 Remove the four 5 mm screws and remove the muffler protector 5 mm SCREWS 2 Remove the three 6 mm bolts and remove the muffler the spark arrester and the muffler gasket MUFFLER GASKET SPARK ARRESTER MUFFLER gt S sD 6 mm BOLTS LK 48 3 Use a brush to remove carbon deposits from
43. ough idle Misfiring or backfiring under load e Afterburning backfiring e Black exhaust smoke or high fuel consumption Replacement Parts The emission control systems on your Honda engine were designed built and certified to conform with EPA and California emission regulations models certified for sale in California We recommend the use of genuine Honda parts whenever you have maintenance done These original design replacement parts are manufactured to the same standards as the original parts so you can be confident of their performance The use of replacement parts that are not of the original design and quality may impair the effectiveness of your emission control system A manufacturer of an aftermarket part assumes the responsibility that the part will not adversely affect emission performance The manufacturer or rebuilder of the part must certify that use of the part will not result in a failure of the engine to comply with emission regulations Maintenance Follow the maintenance schedule on Remember that this schedule is based on the assumption that your machine will be used for its designed purpose Sustained high load or high temperature operation or use in unusually wet or dusty conditions will require more frequent service 39 AIR INDEX Models certified for sale in California An Air Index Information hang tag label is applied to engines certified to an emission durability time period in accordance with
44. ow 19 kilowatts All of the United States and Canada Honda must warrant the emission control system on your power equipment engine for the period of time listed below provided there has been no abuse neglect or improper maintenance of your power equipment engine Where a warrantable condition exists Honda will repair your power equipment engine at no cost to you including diagnosis parts and labor Your emission control system may include such parts as the carburetor or fuel injection system the ignition system and catalytic converter Also included may be hoses connectors and other emission related assemblies Manufacturer s Warranty Coverage The 1995 and later power equipment engines are warranted for two years If any emission related part on your engine is defective the part will be repaired or replaced by Honda Owner s Warranty Responsibility As the power equipment engine owner you are responsible for the performance of the required maintenance listed in your owner s manual Honda recommends that you retain all receipts covering maintenance on your power equipment engine but Honda cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance As the power equipment engine owner you should however be aware Honda may deny you warranty coverage if your power equipment engine or a part has failed due to abuse neglect improper maintenance or
45. potential for electrical shock e If an appliance begins to operate abnormally becomes sluggish stops suddenly turn it off immediately Disconnect the appliance and determine whether the problem is the appliance or if the rated load capacity of the generator has been exceeded e Make sure that the electrical rating of the tool or appliance does not exceed that of the generator Never exceed the maximum power rating of the generator Power levels between rated and maximum may be used for no more than 30 minutes NOTICE Substantial overloading will switch off the AC circuit protector Exceeding the time limit for maximum power operation or slightly overloading the generator may not switch the AC circuit protector OFF but will shorten the service life of the generator Limit operation requiring maximum power to 30 minutes Maximum power is 1 000 VA For continuous operation do not exceed the rated power Rated power is 900 VA In either case the total power requirements VA of all appliances connected must be considered Appliance and power tool manufacturers usually list rating information near the model number or serial number 19 AC OPERATION 1 Start the engine and make sure the output indicator light green comes on 2 Plug the appliance Most motorized appliances require more than their rated wattage for startup OUTPUT INDICATOR LIGHT GREEN OVERLOAD INDICATOR
46. refully to avoid spilling fuel Do not fill the fuel tank above the upper limit mark on the fuel strainer NOTICE Fuel can damage paint and plastic Be careful not to spill fuel when filling your fuel tank Damage caused by spilled fuel is not covered under warranty 3 After refueling tighten the fuel tank cap securely Keep the vent OFF for storage or transport and ON to run the generator VENT LEVER OFF 59 Move the generator at least 10 feet 3 meters away from the fueling source and site before starting the engine After initial fueling or anytime the generator is run completely out of fuel starting the engine may require additional pulls of the starter grip This generator utilizes a vacuum operated fuel pump and may require additional pulls to draw fuel into the carburetor BEFORE OPERATION Before using the generator all generator operators must read the following chapters and sections GENERATOR SAFETY CONTROLS e GENERATOR USE pages 17 27 PRE OPERATION CHECK pages 28 32 STARTING THE ENGINE STOPPING THE ENGINE e MAINTENANCE SCHEDULE 41 60 Dimensions SPECIFICATIONS Model EU 1000i Description code EZGA Length 17 8 in 451 mm Width 9 5 242 mm Height 14 9 in 379 mm Dry weight 29 Ibs 13 kg Engine Model GXH50 Engine type 4 stroke overhead valve single cylinder Displacement Bore X Stroke 3 01 cu in
47. s WARNING Battery posts terminals and related accessories contain lead and lead components Wash hands after handling 2 Plug the battery charging cable into the DC receptacle of the generator 3 Connect the red lead of the battery charging cable to the positive battery terminal the black lead to the negative battery terminal OFF PUSH ON nt DC CIRCUIT PROTECTOR DC RECEPTACLE 4 Start the generator 24 NOTICE Do not start the vehicle while the battery charging cable is connected and the generator is running The vehicle or the generator may be damaged An overloaded DC circuit excessive current draw by the battery or a wiring problem will trip the DC circuit protector PUSH button extends out If this happens wait a few minutes before pushing in the circuit protector to resume operation If the DC circuit protector continues to go OFF discontinue charging and see your authorized Honda generator dealer Disconnecting the battery charging cable 1 Stop the engine 2 Disconnect the black lead of the battery charging cable from the negative battery terminal 3 Disconnect the red lead of the battery charging cable from the positive battery terminal 4 Disconnect the battery charging cable from the DC receptacle of the generator 5 Connect the vehicle battery ground cable to the negative battery terminal RED LEAD 25 ECOTHROTTLE SY
48. sition If the engine stops or the Oil Alert indicator light comes on when you pull the starter grip check the engine oil level before troubleshooting in other areas Z OIL ALERT INDICATOR Art LIGHT RED a 0 GROUND TERMINAL The generator ground terminal is connected to the frame of the generator the metal non current carrying parts of the generator and the ground terminals of each receptacle Before using the ground terminal consult a qualified electrician electrical inspector or local agency having jurisdiction for local codes or ordinances that apply to the intended use of the generator 2 GROUND TERMINAL 14 ECO THROTTLE SWITCH The Eco Throttle system automatically reduces engine speed when all loads are turned off or disconnected When appliances are turned on or reconnected the engine returns to the proper speed to power the electrical load If high electrical loads are connected simultaneously turn the Eco Throttle switch to the OFF position to reduce voltage changes When using the DC output turn the Eco Throttle switch to the OFF position ON Recommended to minimize fuel consumption and further reduce noise levels when no load is applied to the generator OFF The Eco Throttle system does not operate ECO THROTTLE SWITCH OFF eN 2 PARALLEL OPERATION OUTLETS These outlets are_used for connecting two
49. ssion control system warranty regulation is in effect Emission Control System Warranty Parts SYSTEMS COVERED PARTS BY THIS WARRANTY DESCRIPTION Fuel Metering Carburetor assembly includes starting enrichment system Engine temperature sensor Engine control module Fuel regulator Intake manifold Evaporative Fuel tank Fuel cap Fuel hoses Vapor hoses Carbon canister Canister mounting brackets Fuel strainer Fuel cock Fuel pump Fuel hose joint Seal cap Canister purge hose joint Exhaust Catalyst Exhaust manifold Air Induction Air filter housing Air filter element Crankcase breather tube Ignition Flywheel magneto Ignition pulse generator Crankshaft position sensor Power coil Ignition coil assembly Ignition control module Spark plug cap Spark plug Miscellaneous Parts Tubing fittings seals gaskets and clamps associated with these listed systems Note This list applies to parts supplied by Honda and does not cover parts supplied by the equipment manufacturer Please see the original equipment manufacturer s emissions warranty for non Honda parts Covered up to the first required replacement only See the Maintenance Schedule 41 69 INDEX COMPONENT IDENTIFICATION 9 3 CONTROLS saarni 11 12 DC Circuit PrOteCtOr
50. tivities that may expose you to carbon monoxide 1 Perform PRE OPERATION page 28 2 Make sure that all appliances are disconnected from the AC receptacles 3 Turn the fuel cap vent lever to the ON position 4 To start a cold engine move the choke lever to the CLOSED position To restart a warm engine leave the choke lever in the OPEN position 5 Turn the engine switch to the ON position 6 Pull the starter grip lightly until you feel resistance then pull briskly NOTICE Do not allow the starter grip to snap back against the engine Return it gently to prevent damage to the starter or housing 33 7 the choke lever was moved to the CLOSED position to start the engine gradually move it to the OPEN position as the engine warms up 8 If you wish to use the Eco Throttle system turn the Eco Throttle switch to the ON position after the engine has warmed up for 2 or 3 minutes 9 Refer to the AC OPERATION or DC OPERATION see for connecting loads to the generator 34 STOPPING THE ENGINE STOPPING THE ENGINE To stop the engine in an emergency simply turn the engine switch to the OFF position Under normal conditions use the following procedure 1 Unplug appliances from the generator receptacles 2 Turn the engine switch to the OFF position The fuel valve will automatically close 3 Turn the vent lever to the OFF position 4 If two generators were connected for parallel
51. unapproved modifications You are responsible for presenting your power equipment engine to a Honda Power Equipment dealer as soon as a problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days 66 If you have any questions regarding your warranty rights and responsibilities you should contact the Honda Office in your region American Honda Motor Inc Honda Canada Inc Power Equipment Customer Power Equipment Customer Relations or Relations 4900 Marconi Drive 715 Milner Avenue Alpharetta Georgia 30005 8847 Toronto ON M1B 2K8 Telephone 770 497 6400 Telephone 888 946 6329 Warranty Coverage Honda power equipment engines manufactured after anuary 1 1995 and sold in the State of California U S EPA certified engines manufactured on or after September 1 1996 and sold in all of the United States and Canadian certified engines manufactured on or after J anuary 1 2005 are covered by this warranty for a period of two years from the date of delivery to the original retail purchaser This warranty is transferable to each subsequent purchaser for the duration of the warranty period Warranty repairs will be made without charge for diagnosis parts or labor All defective parts replaced under this warranty become the property of Honda Warranted parts are listed under Emission Control System Warranty Parts Normal maintenance items such as spark plugs and filters
52. urn it off immediately Disconnect the appliance and determine whether the problem is the appliance or if the rated load capacity of the generator has been exceeded e Make sure that the electrical rating of the tool or appliance does not exceed that of the generator Never exceed the maximum power rating of the generator Power levels between rated and maximum may be used for no more than 30 minutes e Never connect different generator models and types e Use only a Honda approved parallel operation kit optional equipment when connecting two EU1000i generators for parallel operation e Never connect or remove the parallel operation kit when the generator is running For single generator operation the parallel operation kit must be removed NOTICE Substantial overloading that continuously lights the overload indicator light red may damage the generator Marginal overloading that temporarily lights the overload indicator light red may shorten the service life of the generator 21 Limit operation requiring maximum power to 30 minutes Maximum power in parallel operation is 2 0 KVA For continuous operation do not exceed the rated power Rated power in parallel operation is 1 8kVA In either case the total power requirements VA of all appliances connected must be considered Appliance and power tool manufacturers usually list rating information near the model number or serial number 22 AC PAR
Download Pdf Manuals
Related Search