GE 28300 Telephone User Manual
Contents
1. FIBRE CHANNEL SWITCH INSTALLATION XX oLoeic Quick Start Guide Installation Instructions Congratulations on your purchase of the QLogic 3810 Fibre Channel Switch This guide describes the steps to install and activate your new switch using a Windows workstation For advanced options and instructions including Solaris Linux and Mac OS X installations refer to the QLogic 3810 Fibre Channel Switch Installation Guide which is available at www qlogic com Do not apply power to the switch until instructed in Step 4 Step 1 Verify the Package Contents The QLogic 3810 Fibre Channel Switch is shipped with the following items QLogic 3810 Fibre Channel Switch AC Power cord Rubber feet SFP optical transceivers optional on Some models include SFPs or SFPs can be ordered separately If you ordered SFPs separately they will arrive in a different package Step 2 Mount the Switch O Fora surface mount attach the rubber feet to the locations on the bottom of the switch For a rack mount install the QLogic 3800 5800 Series rail kit and the switch in a standard 19 rack as described in the QLogic 3800 5800 Series Fibre Channel Switch Rack Mounting Guide Step 3 Install Transceivers An SFP transceiver is required for each SFP port that will be connected to a device The QLogic 3810 Switch SFP ports support 2Gbps 4Gbps and 8Gbps transmission Do not attempt to configure a port to 1Gbps that has an 8Gbps S2. FP installed doing so will down the port Q To install an SFP transceiver insert the transceiver into the switch port and gently press until it snaps in place The transceiver will fit only one way If the transceiver does not install under gentle pressure flip it over and try again Step 4 Apply Power to the Switch input L Plug the AC power cord into the switch and into a wall outlet or power strip Verify that the Input Power LED is lit Q The switch runs its self tests and begins normal SYSTEM operation this may take a few minutes Verify that FAULT LED the Heartbeat LED is blinking once per second and the System Fault LED is not lit Step 5 Verify Workstation Requirements L Verify that your workstation can support the QuickTools application with the following minimum requirements Windows 2003 or Windows XP SP1 SP2 512MB memory minimum 1GB recommended 1GHz processor Video card with 256 colors RJ 45 Ethernet port Internet Browser Microsoft Internet Explorer 6 0 and later Firefox 1 5 and later Safari 1 0 for Windows Java 2 Standard Edition Runtime Environment 1 4 2 to support the Web applet Q The default IP address of a new switch is 10 0 0 1 Ensure that your workstation is configured to communicate with the 10 0 0 subnet Step 6 Connect the Workstation to the Switch Q Connect the workstation to the switch using an Ethernet cable the switch automatically recognizes both straigh
3. http support qlogic com E mail support qlogic com The QLogic knowledge database contains troubleshooting information for the QLogic adapters Access the data base from the QLogic Support Web page http support glogic com Use the Support Center search engine to look for specific troubleshooting information Corporate Headquarters International Offices AX QLogic Corporation UK Ireland Germany France e 26650 Aliso Viejo Parkway India Japan China QLOGIC Aliso Viejo CA 92656 Hong Kong Singapore Taiwan 949 389 6000 www glogic com 2012 QLogic Corporation QLogic the QLogic logo and QuickTools are registered trademarks or trademarks of QLogic Corporation Microsoft Windows and Internet Explorer are registered trademarks of the Microsoft Corporation MacOSX and Safari are registered trademarks of Apple Computer Inc Linux is a registered trademark of Linus Torvalds Firefox is a registered trademark of the Mozilla Foundation Java and Solaris are registered trademarks of Oracle Corporation All other brands and product names are trademarks or registered trademarks of their respective owners Information supplied by QLogic is believed to be accurate and reliable QLogic Corporation assumes no responsibility for any errors in this brochure QLogic Corporation reserves the right without notice to makes changes in product design or specifications 59267 01 A
4. t and cross over cables If you are using a Windows workstation you must have a live Ethernet connection when the workstation powers up Step 7 Log In to the Switch You can log in to and manage the switch using the command line interface CLI or the QuickTools Web applet This guide describes the use of QuickTools Q To start the QuickTools Web applet open an Internet browser and then type the default IP address 10 0 0 1 L Login to the switch using the default user name admin and password password Step 8 Run the Configuration Wizard L Obtain the IP address and subnet mask from your network administrator CL Open the QuickTools Wizards menu and select Configuration Wizard Follow the instructions to set network parameters and the password The default user name is admin the default password is password Changing the IP address will terminate the QuickTools session L Open an Internet browser and type the new IP address to log in to switch Step 9 Connect Devices Q Connect fiber optic cables between the installed transceivers and their corresponding devices Each port auto negotiates the correct port type with the connected device Congratulations You have successfully installed your QLogic 3810 Switch Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance QLogic Technical Support can be reached by the following methods Web
Download Pdf Manuals
Related Search