GE 197D7799P001 Refrigerator User Manual
Contents
1. To replace a burned out bulb unplug the refrigerator from its electrical outlet unscrew the bulb when cool and replace it with an appliance bulb of the same or lower wattage Turning the control to the 0 position does not remove power to the light circuit Preparing for Vacation For long vacations or absences remove food and unplug the refrigerator Move the temperature control dial to the 0 position and clean the interior with a baking soda solution of one tablespoon 15 ml of baking soda to one quart 1 liter of water Leave the doors open Move the feeler arm to the STOP up position and shut off the water supply to the refrigerator If the temperature can drop below freezing have a qualified servicer drain the water supply system on some models to prevent serious property damage due to flooding Preparing to Move Secure all loose items such as grille shelves and drawers by taping them securely in place to prevent damage Be sure the refrigerator stays in an upright position during moving Installation Instructions mosis 16 17 18 If you have questions call 1 800 GE CARES or visit our Website at ge com In Canada call 1 800 561 3344 or Visit our Website at WWW geappliances ca BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTAN T Save these instructions for local inspector s use IMPORTAN T Observe all governing codes and ordinances Note to Installer Be2. l alimentation lectrique de l ampoule n est pas coup e Ne recongelez pas les aliments surgel s qui ont Si votre r frig rateur est dot d une machine compl tement d gel 3 gla ons automatique vitez le contact avec les suoyjaonysuy ajes suononysuy Guyesadg 2 A S a S a sdij Bunooysajqnoi pioddns sauinsuoy Safety Instructions A S S i ra D X PA S S S i ra S g Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING ef Vile Sf READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY CON SAVE THESE INSTRUCTIONS A WARNING v HOW TO CONNECT ELECTRICITY Do not under any circumstances cut or remove the third ground prong from the power cord For personal safety this appliance must be properly grounded The power cord of this appliance is equipped with a 3 prong grounding plug which mates with a standard 3 prong grounding wall outlet to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet The refrigerator should always be plugged into its
3. aes Temperature control dial e Move the temperature control dial to a temperature in O position setting Refrigerator is unplugged e Push the plug completely into the outlet The fuse is blown circuit e Replace fuse or reset the breaker breaker is tripped Vibration or rattling slight Roller screws or leveling legs See Rollers and Leveling Legs vibration is normal need adjusting Fresh food or freezer Temperature control dial See About the temperature control dial compartment too warm not set cold enough Warm weather or frequent Set the temperature control dial one step colder door openings See About the temperature control dial Door left open e Check to see if package is holding door open Package blocking air duct in Check to see if package is blocking air duct in freezer freezer compartment compartment 17 suoyaonysuy ajes suononysuy Guyesadg A A S Q 5 a sdij Bunooysajqnou pioddns sauinsuoy Safety Instructions Operating Instructions S S S S amp Troubleshooting Tips Consumer Support Before you call for service Troubleshooting Tips Problem Motor operates for long periods or cycles on and off frequently Modern refrigerators with more storage space and a larger space and a larger freezer require more operating time They start and stop often to maintain even temperatur
4. and use is not permitted in Massachusetts Consult with your licensed plumber Install the shutoff valve on the nearest frequently used drinking water line ROUTE THE TUBING Route the tubing between the cold water line and the refrigerator Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible NOTE Be sure there is sufficient extra tubing about 8 feet 244 cm coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation 5 CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Make sure the tubing is fully inserted into the valve Tighten the compression nut securely TM For plastic tubing from a GE SmartConnect Refrigerator Tubing kit insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight then tighten one additional turn with a wrench Overtightening may cause leaks Compression Nut Saddle Type Shutoff Valve 4 SmartConnect Tubing Outlet Valve Ferrule sleeve NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber 6 FLUSH OUT THE TUBING Turn th
5. brands covered up to 15 years old in the continental U S SPP is a trademark of General Electric Company 20 For refrigerators installed in the U S a ee B mm Please place in envelope and mail to General Electric Company Warranty Registration Department P O Box 32150 Louisville KY 40232 2150 cf i Sn ss ss sms aS me mn Sh ce Tl S a gt oS D Q gt ey gt Q a 3 y Ss ET Please place in envelope and mail to Veuillez mettre dans une enveloppe et envoyez OWNERSHIP REGISTRATION P 0 BOX 1780 MISSISSAUGA ONTARIO L4Y 461 FOR CANADIAN CONSUMERS ONLY For refrigerators installed in the U S Se Cut here Consumer Product Ownership Registration Model Number Serial Number Mr Ms Mrs Miss First Last Name Name Street Address l l l l Apt E mail Address Date Placed Ph Re la Er Number ia Faire Please provide your e mail address to receive via e mail discounts special offers and other important communications from GE Appliances GEA Check here if you do not want to receive communications from GEA s carefully selected GE Consumer amp Industrial Appliances partners General Electric Company FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR Louisville KY 40225 WARRANTY RIGHTS ge com For information about GEA s privacy an
6. channel and gently lowering the front into place 3 Replace the drawers When the bin fills to the level of the feeler arm the icemaker will stop producing ice It is normal for several cubes to be joined together F ice is not used frequently old ice cubes will become cloudy taste stale shrink or fuse together On power switch models the green power light will blink if ice cubes get stuck in the icemaker To correct this set the power switch to O off and remove the cubes Set the power switch to I on to restart the icemaker After the icemaker has been turned on again there will be a delay of about 45 minutes before the icemaker resumes operation NOTE In homes with lower than average water pressure you may hear the icemaker cycle multiple times when making one batch of ice Icemaker Accessory Kit If your refrigerator did not already come equipped with an automatic icemaker an icemaker accessory kit is available at extra cost Check the back of the refrigerator for the specific icemaker kit needed for 7 your model suoyaonysuy ajes suoyonysu Guyesadg A q A S Q 5 a sdij Bunooysajqnoi pioddns sauinsuoy Safety Instructions Operating Instructions S S S amp amp Troubleshooting Tips Consumer Support Care and cleaning of the refrigerator Cleaning the Outside The door handles and trim on some mod
7. or from service delays beyond their reasonable control To obtain warranty service purchaser must present the original Bill of Sale Components repaired or replaced are warranted through the remainder of the original warranty period only This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within Canada In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide This warranty is in addition to any statutory warranty WHAT IS NOT COVERED e Owner is responsible to pay for service calls related to product installation and or teaching how to use the product e Damage to finish must be reported within 48 hours following the delivery of the appliance e Damage to finish after delivery e Improper installation proper installation includes adequate air circulation to the refrigeration system adequate electrical plumbing and other connecting facilities e Replacement of house fuses or resetting of circuit breakers e Replacement of light bulbs e Damage to product caused by accident fire floods or acts of God e Loss of food due to spoilage e Proper use and care of product as listed in the owner s manual proper setting of controls e Product not accessible to provide required service e WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive remedy is
8. remedy is product repair as provided in this Limited Warranty Any implied warranties including the implied warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA If the product is located in an area where service by a GE Authorized Servicer is not available you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 23 suo n nysuj Ajajes suonannsuj Guyesadg A a 2 S a S 7 sdij bunooysajqnosj pioddngs sauinsuoy Consumer Support ge com GE Appliances Website In the US www Hotpoint com Have a question or need assistance with your appliance Try the GE Appliances Website 24 hours a day any day of the year For greater convenience and faster service you
9. select allows at least 8 2 4 m as described above NOTE The only GE approved plastic tubing is that supplied in GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Certain types of plastic will crack or rupture with age and cause water damage to your home A GE water supply kit containing tubing shutoff valve and fittings listed below is available at extra cost from your dealer or from Parts and Accessories 1 800 661 1616 A cold water supply The water pressure must be between 20 and 120 p s i 1 4 8 1 bar Power drill 1 2 or adjustable wrench Straight and Phillips blade screwdriver Two 1 4 outer diameter compression nuts and 2 ferrules sleeves to connect the copper tubing to the shutoff Ss valve and the refrigerator water valve OR If you are using a GE SmartConnect Refrigerator Tubing kit the necessary fittings are preassembled to the tubing If your existing copper water line has a flared fitting at the end you will need an adapter available at plumbing supply stores to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting Do not cut formed end from GE SmartConnect Refrigerator tubing Shutoff valve to connect to the cold water line The shutoff valve should have a water inlet with a minimum in
10. their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Order on line today 24 hours every day or by phone at 1 800 661 1616 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Customers in Canada should consult the yellow pages for the nearest Mabe service center or call 1 800 661 1616 ge com Contact Us In the U s WwwHotpoint com KoA If you are not satisfied with the service you receive from GE contact us on our Website with all the details including your phone number or write to General Manager Customer Relations GE Appliances Appliance Park Louisville KY 40225 In Canada www geappliances ca or write to Director Consumer Relations Mabe Canada Inc Suite 310 1 Factory Lane Moncton N B E1C 9M3 ge com Register Your Appliance In the U S www Hotpoint com Register your new appliance on line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material In Canada www geappliances ca 5 Printed in the United States cs Printed on Recycled
11. AL i 5 1 AREA CODE IND R G TELEPHONE E MAIL a i FE DID YOU PURCHASE A SERVICE CONTRACT FOR THIS APPLIANCE YES OU O eae EXFIRATION 1 M AVEZ VOUS ACHET UN CONTRAT DE SERVICE POUR CET APPAREIL NO NON O 1 Z 1 Pour les 9 1 A NAME OF SELLING DEALER NOM DU MARCHAND MODEL MODELE Consommateurs lt i Canadiens 5 1 D i 1 I 1 l 1 l 1 1 1 1 1 I 1 I 1 I l I Refr iger ator Warr anty For customers in the United States All warranty service provided by our Factory Service Centers Staple your receipt here Ca or an authorized Customer Care technician To schedule service Proof of the original purchase on line 24 hours a day visit us at ge com or call 800 GE CARES date is needed to obtain service 800 432 2737 Please have serial number and model number under the warranty available when calling for service For The Period Of GE Will Replace GE and GE PROFILE MODELS One Year Any part of the refrigerator which fails due to a defect in materials or workmanship From the date of the During this limited one year warranty GE will also provide free of charge all labor and original purchase related service to replace the defective part Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship Water filter if included During this limited thirty day warranty GE will also provide free of charge a replacement water Fr
12. HE HARDWARE conr 4 2 Interchange hinge and screws at top right with screws at top left of cabinet Do not tighten screws on hinge side at this time Installing the hinge on the left Installing the hinge on the right NOTES Some hinges have four holes Which holes you use for installing the hinge depends on which side you install the hinge The outer edge of the hinge should be parallel to the edge of the case for correct installation REVERSING THE DOOR HANDLES 5 1 Transfer fresh food door handle 5 1 1 Remove the handle plug using a tape tipped putty knife under the edge and remove the screw underneath Remove the two screws i holding the handle to the top of the door 5 1 2 Remove the handle 5 1 3 Remove the screws from the right edge of the door top and insert them into the handle screw holes on the opposite side Screws for Handle Holes 5 REVERSING THE DOOR HANDLES cont 5 1 4 Remove plug button from the top hinge hole on the left side of the door and insert it into the hole on the opposite side that was vacated by removal of the top hinge Plug Button 5 1 5 Pull the plug button from the front of the door and transfer it to the opposite side To reattach the handle on the Plug Button opposite side 5 2 Transfer door stop 5 2 1 Move the metal or plastic door stop and screws from the right side to the left side Metal Door Stop Left Side Im Left Side QE 5 3 Re
13. ITE Ed N Lorsque vous utilisez un appareil lectrique observez toujours les mesures de s curit de base y compris les suivantes Installez le r frig rateur conform ment aux pi ces mobiles du m canisme jecteur ou avec directives d installation avant de l utiliser l ment chauffant qui lib re les gla ons Ne posez pas les doigts ou les mains sur le m canisme de la machine gla ons pendant que le r frig rateur est branch Ne laissez pas les enfants grimper s asseoir se tenir debout ni se pendre aux clayettes du r frig rateur Ils pourraient endommager le r frig rateur et se blesser gravement Ne touchez pas les surfaces froides du cong lateur si vous avez les mains humides ou mouill es la N entreposez et n utilisez pas d essence ou f one a P p peau risque d adh rer ces surfaces tr s froides autres vapeurs et liquides inflammables proximit de cet appareil ou de tout autre D branchez votre r frig rateur avant de le appareil lectrom nager nettoyer ou de le r parer loignez les doigts des parties du r frig rateur REMARQUE Nous vous recommandons vivement de o l on peut facilement se pincer les espaces confier toute r paration un technicien qualifi entre les portes et entre les portes et les placards sont toujours troits Soyez prudent lorsque vous fermez les portes de l appareil en pr sence des enfants Lorsque vous r glez la commande sur 0 teint
14. Paper
15. Si la prise murale est du type standard 2 alv oles il vous incombe de la faire remplacer par une prise 3 alv oles correctement mise la terre Le r frig rateur doit toujours tre branch dans sa propre prise de courant dont la tension nominale est identique celle indiqu e sur la plaque signal tique CONSERVEZ CES DIRECTIVES Cette pr caution est recommand e pour garantir un rendement optimum et viter une surcharge des circuits lectriques de la r sidence ce qui pourrait cr er un risque d incendie par surchauffe des fils Ne d branchez jamais le r frig rateur en tirant sur le cordon d alimentation Saisissez fermement la fiche du cordon et tirez droit pour la retirer de la prise R parez ou remplacez imm diatement tout cordon effiloch ou endommag N utilisez pas un cordon fendill ou pr sentant des signes d usure Lorsque vous d placez votre r frig rateur du mur faites attention de ne pas le faire rouler sur le cordon d alimentation afin de ne pas l endommager About the temperature control dial Turning the dial to 0 stops cooling in both compartments tfresh food and freezer It does not shut off power to the refrigerator er ge com Temperature Control Dial on some models The temperature control dial has nine settings plus 0 1 is the warmest 9 is the coldest At first set the dial at 5 After using the refrigerator adjust the dial if necessary About the fresh foo
16. appliance properly Model Number Serial Number Important If you did not get a registration card with your product detach and return the form on the next page to ensure that your product is registered or register online at ge com The top card is for products installed in the U S The bottom card is for products installed in Canada GE Service Protection Plus GE a name recognized worldwide for quality and dependability together with Assurant Solutions offers you Service Protection Plus comprehensive protection on your appliances Benefits Include e Prompt reliable service from GE Authorized Servicers e Convenient hours designed to suit your busy schedule e Quality replacement parts e The dependability of GE a name recognized and trusted worldwide e Ask about our interest free payment plans With Service Protection Plus you can expect e An extended service plan that limits unexpected repair bills e Service coverage for most major brands e Unlimited service calls for the length of your contract or credit toward a replacement product e Service coverage for covered operating parts and labor on appliances and home electronics that fail during normal single family household use e Your satisfaction is our goal We strive to provide you with excellent service in a professional and timely manner Place your confidence in GE and call us in the U S toll free at 1 800 626 2224 for more information Most
17. can now download Owner s Manuals order parts or even schedule service on line In Canada www geappliances ca ge com Schedule Service In the U S www Hotpoint com Expert GE repair service is only one step away from your door Get on line and schedule your service at your convenience 24 hours any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours In Canada call 1 800 561 3344 Real Life Design Studio In the US ge com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 In Canada contact Manager Consumer Relations Mabe Canada Inc Suite 310 1 Factory Lane Moncton N B E1C 9M3 Extended Warranties In the U S ge com Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect You can purchase it on line anytime or call 1 888 261 2133 during normal business hours GE Consumer Home Services will still be there after your warranty expires ge com Parts and Accessories In the U s www Hotpoint com Individuals qualified to service
18. d compartment shelves Shelf supports at various levels allow you to custom space your shelves Not all features are on all models n 2 Lift L and o 1 Tilt up Lift rear A LIT Pull forward To remove the full width shelves Half Width Shelves One end of the shelf rests on a molded side wall support a bracket on the other end hooks into a track on the rear cabinet wall To remove lift the shelf up at front then off the support and out of the track To replace select desired shelf height With shelf front raised slightly hook the bracket s top lug into the track then lower the shelf onto the support Full Width Shelves Some models have a steel wire sliding shelf a stationary tempered glass shelf a spillproof shelf or two steel wire stationary shelves These shelves can be moved to another place in the fresh food compartment The full width sliding shelf has stop locks When placed correctly on the shelf supports the shelf will stop before coming completely out of the refrigerator and will not tilt when you place food on it or remove food from it Spillproof Shelves on some models Spillproof shelves have special edges to help prevent spills from dripping to lower shelves To remove or replace the shelves see the above instructions Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting that is best suit
19. d data usage policy go to ge com and click on Privacy Policy or call 800 626 2224 Zi City State Code l For refrigerators installed in Canada sel a DATE y DATE DISTAL ATION CORRESPONDENCE O ENGLISH CORRESPONDANCE O FRAN AIS SERIAL S RIE O Ido notwish to receive any promotional offers regarding this product O Je ne d sire pas recevoir d offres promotionnelles concernant ce produit EE os a ob ene ee T 1 OWNERSHIP REGISTRATION CERTIFICATE FICHE D INSCRIPTION DU PROPRI TAIRE I I Please register your product to enable us to contact you Veuillez enregistrer votre produit afin de nous permettre de inthe remote event a safety notice is issued for this product communiquer avec vous si jamais un avis de s curit concemant Z M and to allow for efficient communication under the terms ce produit tait mis et de communiquer facilement avec vous en l T of your warranty should the need arise vertu de votre garantie si le besoin s en fait sentir A 1 REGISTER ON LINE www geappliances ca MAILTO PO BOX1780 MISSISSAUGA ENREGISTREMENT SURINTERNET wwwrelectromenagersge ca POSTERA ONTARIO LAY 461 3 i O MR M O MRS MME FIRST NAME PRENOM LAST NAME NOM ZM O MSS MLE O MS 1 For Canadian Si Customers E i STREET NO N RUE STREET NAME RUE APT NO APP RR 9 W CITY VILLE PROVINCE POSTAL CODE POST
20. e main water supply on counterclockwise and flush out the tubing until the water is clear Shut the water off at the water valve after about one quart 1 liter of water has been flushed through the tubing 1 4 Copper Tubing Installation Instructions CONNECT THE TUBING TO THE REFRIGERATOR NOTES Before making the connection to the refrigerator be sure the refrigerator power cord is not plugged into the wall outlet We recommend installing a water filter if your water supply has sand or particles that could clog the screen of the refrigerator s water valve Install it in the water line near the refrigerator If using GE SmartConnect Refrigerator Tubing kit you will need an additional tube WX08X10002 to connect the filter Do not cut plastic tube to install filter Remove the access cover Remove the plastic flexible cap from the water valve refrigerator connection Place the compression nut and ferrule sleeve onto the end of the tubing as shown On GE SmartConnect Refrigerator Tubing kit the nuts are already assembled to the tubing Insert the end of the tubing into the water valve connection as far as possible While holding the tubing tighten the fitting TM For plastic tubing from a GE SmartConnect Refrigerator Tubing kit insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight then tighten one additional turn with a
21. e refrigerator has not been connected Water shutoff valve connecting refrigerator to water line may be clogged Move the feeler arm to the STOP up position Keeping it on will damage the water valve e Call the plumber to clear the valve Door left open e Check to see if package is holding door open Temperature control dial e See About the temperature control dial not set cold enough Ice storage bin needs cleaning Empty and wash bin Discard old cubes Food transmitting odor taste Wrap foods well to ice cubes Interior of refrigerator e See Care and cleaning needs cleaning Not unusual during e Wipe surface dry and reset temperature control dial periods of high humidity one setting colder Too frequent or too long door openings Foods transmitting e Foods with strong odors should be tightly wrapped odor to refrigerator Keep an open box of baking soda in the refrigerator replace every three months Interior needs cleaning e See Care and cleaning CUSTOMER WARRANTY for customers in Canada Your refrigerator is warranted to be free of defects in material and workmanship RER AA SSSR SSSR SSSR PSS Rea arias es aS eS eS OS ORS OOOO ORR ORI DOR DRI DRO ERODE ROR ROE SRR NCR RRR OR RRR RON RNR PR RL RRR NS SOF SOOT OF OF OF OT OT IOS SO SISSIES e m2 What is covered How Long Warranted From Date of Sale Compressor GE Profile Ten 10 Years GE and All Oth
22. ed Leveling legs should be set so the front of the refrigerator is raised just enough that the doors close easily when opened about halfway Turn the leveling legs clockwise to raise the refrigerator counterclockwise to lower it Rollers next to the leveling legs allow you to move the refrigerator away from the wall for cleaning Turn the legs counterclockwise until the weight of the refrigerator is transferred from them to the rollers After rolling the refrigerator back into place turn the legs clockwise until the legs again bear the weight of the refrigerator G Installation Instructions ET INSTALLING THE WATER LINE on some MODELS BEFORE YOU BEGIN Recommended copper water supply kits are WX8X2 WX8X3 or WX8X4 depending on the amount of tubing you need Approved plastic water supply lines are GE SmartConnect Refrigerator Tubing WX08X10006 WX08X10015 and WX08X10025 When connecting your refrigerator to a GE Reverse Osmosis Water System the only approved installation is with a GE RVKit For other reverse osmosis water systems follow the manufacturer s recommendations This water line installation is not warranted by the refrigerator or icemaker manufacturer Follow these instructions carefully to minimize the risk of expensive water damage Water hammer water banging in the pipes in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding Call a qualified plumber to c
23. ed to your needs Allow 24 hours for the refrigerator to get cold NOTE The shelf to the right of the track is designed to hook into the right hand slot the shelf to the left is designed to hook into the left hand slot m Pull forward and down To remove a full width shelf when the fresh food compartment door cannot be opened fully suoyaonysuy ajes suonannsuj Guyesadg a A S Q 5 a sdij Gunooysajqnou pioddns sauinsuoy Safety Instructions Operating Instructions S S S 3 S amp Troubleshooting Tips Consumer Support About the freezer compartment shelves Step Shelf To remove the step shelf 7 Lift left side of shelf slightly 3 Lower right side of shelf move shelf to the right and take it out 2 Move shelf to the left to free its right ends from holes in the cabinet wall To replace the step shelf 7 With shelf tilted as shown fit left ends Lift left side of shelf slightly swing shelf of shelf into holes in cabinet wall up fit right ends of shelf into holes in cabinet wall and lower shelf into place About the storage drawers Not all features are on all models Yd MEN Fruit and Vegetable Drawers Excess water that may accumulate in the bottom of the drawers should be e
24. els Clean with a cloth dampened with soapy water Dry with a soft cloth Keep the outside clean Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent Dry and polish with a clean soft cloth The stainless steel panels and door handles on some models can be cleaned with a commercially available stainless steel cleaner Do not use appliance wax or polish on the stainless steel Do not wipe the refrigerator with a soiled dish cloth or wet towel These may leave a residue that can erode the paint Do not use scouring pads powdered cleaners bleach or cleaners containing bleach because these products can scratch and weaken the paint finish Cleaning the Inside To help prevent odors leave an open box of baking soda in the fresh food and freezer compartments Unplug the refrigerator before cleaning If this is not practical wring excess moisture out of sponge or cloth when cleaning around switches lights or controls Use warm water and baking soda solution about a tablespoon 15 ml of baking soda to a quart 1 liter of water This both cleans and neutralizes odors Rinse and wipe dry After cleaning the door gaskets apply a thin layer of petroleum jelly to the door gaskets at the hinge side This helps keep the gaskets from sticking and bending out of shape Avoid cleaning cold glass shelves on some models with hot water because the extreme temperature difference may cau
25. er Brands One 1 Year GE Profile Five 5 Years GE and All Other Brands One 1 Year One 1 Year Sealed System including evaporator condenser tubing and refrigerant All Other Parts Pye SA SSL Se Parts Repair or Replace at Mabe s Option GE Profile Ten 10 Years GE and All Other Brands One 1 Year GE Profile Five 5 Years GE and All Other Brands One 1 Year One 1 Year GE Profile Five 5 Years GE and All Other Brands One 1 Year GE Profile Five 5 Years GE and All Other Brands One 1 Year One 1 Year CS CSS 4 2G a SNC OE NOR OT OLE OE ER CR EEG ERE EGER NEI GER GEREGE SPOOF IIT OI OTP ROP ROTO BOF ROBOT ROT POT ROP ROOTED RTS CR a Da OLD CS ae DDO DOD ee Oe DODD Dat es ISISI ROT OS OT OOS OS OOS OSTEO PLD LD ELD LD ELD LD LD LD LD NED LD LE aaa LR LR LR LR LR LR LS TERMS AND CONDITIONS This warranty applies only for single family domestic use in Canada when the Refrigerator has been properly installed according to the instructions supplied by Mabe and is connected to an adequate and proper utility service Damage due to abuse accident commercial use and alteration or defacing of the serial plate cancels all obligations of this warranty Service during this warranty period must be performed by an Authorized Mabe Service Agent Neither Mabe nor the Dealer is liable for any claims or damages resulting from failure of the Refrigerator
26. es Frost or ice crystals on frozen food frost within package is normal Automatic icemaker does not work on some models Frequent buzzing sound Cubes too small Slow ice cube freezing Ice cubes have odor taste Moisture forms on cabinet surface between the doors Moisture collects inside in humid weather air carries moisture into refrigerator when doors are opened Refrigerator has odor 18 Possible Causes Normal when refrigerator is first plugged in What To Do e Wait 24 hours for the refrigerator to completely cool down Often occurs when large amounts of food are e This is normal placed in refrigerator Door left open e Check to see if package is holding door open Hot weather or frequent e This is normal door openings Temperature control dial e See About the temperature control dial set at the coldest setting Grille and condenser See Care and cleaning need cleaning Door left open e Check to see if package is holding door open Too frequent or too long door openings Icemaker is not on e Move the feeler arm to the ON down position Water supply turned off or e See Installing the water line not connected Freezer compartment e Wait 24 hours for the refrigerator to completely too warm cool down Piled up cubes in the storage Level cubes by hand bin cause the icemaker to shut off Icemaker is on but the water supply to th
27. face for the doors IMPORTANT Once you begin do not move the cabinet until door swing reversal is completed These instructions are for changing the hinges from the right side to the left side if you ever want to change the hinges back to the right side follow these same instructions and reverse all references to left and right TOOLS REQUIRED SS Masking tape g 8 Phillips screwdriver eae Qe T20 or T25 Torxdriver needed for some models gE 5 16 open end wrench 5 16 hex head socket driver Putty knife or thin blade screwdriver BEFORE YOU START 1 1 Unplug the refrigerator from its electrical outlet 1 2 Empty all door shelves including the dairy compartment CAUTION Do not let either door drop to the floor To do so could damage the door stop 13 2 REMOVE THE FREEZER DOOR 2 1 Tape the door shut with masking tape 2 2 With a 5 16 hex head socket driver remove the screws that hold the top hinge to the cabinet 2 3 Lift the hinge straight up to free the hinge pin from the socket in the top of the door and set it aside along with its screws Top Hinge 2 4 Remove the tape and tilt the door away from the cabinet Lift it off the center hinge pin P 2 5 Set the door on a non scratching surface with the outside up 2 6 Transfer the 2 screws from the opposite side of the cabinet to the screw holes vacated by the top hinge removal Installatio
28. fans are helping to maintain the correct temperatures CLICKS POPS CRACKS and CHIRPS E You may hear cracking or popping sounds when the refrigerator is first plugged in This happens as the refrigerator cools to the correct temperature E The compressor may cause a clicking or chirping sound when attempting to restart this could take up to 5 minutes E Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound E On models with an icemaker after an icemaking cycle you may hear the ice cubes dropping into the ice bucket Before you call for service Troubleshooting Tips WATER SOUNDS E The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water E Water dropping on the defrost heater can cause a sizzling popping or buzzing sound during the defrost cycle M A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan E Closing the door may cause a gurgling sound due to pressure equalization For additional information on normal icemaker operating sounds see the About the automatic icemaker section D Save time and money Review the charts on the following Q pages first and you may not need to call for service Problem Possible Causes What To Do Refrigerator does not Refrigerator in defrost cycle Wait about 30 minutes for defrost cycle to end
29. install the fresh food door handle 5 3 1 Attach the handle to the right side of the door with screws at the top and under the handle plug 5 3 2 Reinstall the handle plug Installation Instructions FA REVERSING THE DOOR SWING cont 5 REVERSING THE DOOR HANDLES conr 5 4 Transfer Freezer Door Handle 5 4 1 Remove the screw holding the handle to the top of the door and the two screws holding the handle to the bottom of the door 5 4 2 Remove the handle 5 4 3 Remove the screw from the right top edge of the door and insert it into the handle screw hole on the left side Transfer the door stop as shown in preceding section 5 2 5 4 5 Attach the handle to the right edge of the door with screws at top and bottom using bottom holes vacated by removal of the door stop screws RE HANGING THE DOORS 6 1 Re hang the fresh food door 6 1 1 Lower the fresh food door onto the bottom hinge pin Be sure the washer is in place on the pin pae Plastic Washer 6 RE HANGING THE DOORS CONT 6 1 2 Insert the pin on the center hinge into the socket in the top of the door Place the spacer then the washer on the hinge pin NOTE The center hinge must be turned over as shown when mounted on the left side Plastic Washer and Spacer Tilt the door toward the cabinet As the door is brought into position slide the hinge under the head of the screw which earlier had been partl
30. lop Freezer igerators Refr ge com Safety Instructions 2 4 Operating Instructions Automatic Icemaker 7 Care and Cleaning 8 SHEIVES rss RUE RE era ride 5 6 Storage Drawers 6 Temperature Controls 5 Installation Instructions Preparing to Install the Refrigerator 4 4 sais sa 9 Reversing the Door Swing 13 16 Water Line Installation 10 12 Troubleshooting Tips Before You Call For Service 17 18 Normal Operating Sounds 17 Consumer Support Consumer Support Back Cover Product Registration Canadian 21 22 Product Registration U S 20 22 Warranty for Canadian Customers 19 Warranty for U S Customers 23 Write the model and serial numbers here Model Serial You can find them on a label on the upper left side of the fresh food compartment Owner s Manual and Installation Instructions Models 16 17 18 197D7799P001 49 60521 1 08 08 JR Safety Instructions A S S i ra D X PA S S S i ra S g Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING DANGER RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Child entrapment and suffocation are not Refrigerants problems of the past Junked or abandoned refrigerators are still dangerous e
31. losing doors when children are and located in accordance with the Installation in the area Instructions before it is used 335 In refrigerators with automatic icemakers Do not allow children to climb stand or hang avoid contact with the moving parts of the on the shelves in the refrigerator They could ejector mechanism or with the heating element damage the refrigerator and seriously injure that releases the cubes Do not place fingers or themselves hands on the automatic icemaking mechanism Do not touch the cold surfaces in the freezer while the refrigerator is plugged in compartment when hands are damp or wet Unplug the refrigerator before cleaning and Skin may stick to these extremely cold surfaces making repairs Do not store or use gasoline or other flammable NOTE We strongly recommend that any servicing be vapors and liquids in the vicinity of this or any performed by a qualified individual other appliance Turning the control to the 0 position does Keep fingers out of the pinch point areas not remove power to the light circuit clearances between the doors and between the doors and cabinet are necessarily small MESURES DE S CURIT IMPORTANTES LISEZ D ABORD TOUTES LES DIRECTIVES A AVERTISSEMENT N utilisez cet lectrom nager que pour l usage auquel il est destin comme expliqu dans le Do not refreeze frozen foods which have thawed completely pr sent manuel is Z 2 f2 MESURES DE SECUR
32. mptied and the drawers wiped dry Snacks Drawer The snacks drawer can be moved to the most useful location for your family s needs About storage drawer and cover removal Not all features are on all models Humidity Control iF HIGH LOW ge com Adjustable Humidity Drawer on some models Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables Drawer and Cover Removal Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits Drawers can be removed easily by grasping the sides and lifting up slightly while pulling drawers past the stop location Full Width Drawer with Plastic Cover To remove the cover lift it off its supports pull it forward tilt it and take it out Twin Drawer Shelf To remove 7 Remove the drawers 2 Reach in push the front of glass cover up and at the same time pull it forward as far as it will come Tilt it and take it out Avoid cleaning the cold glass cover with hot water because the extreme temperature difference may cause it to break Remove the drawer frame Always remove the glass cover before you take out the drawer frame Lift the frame off the supports at each side and back pull it forward tilt it and take it out About the automatic icemaker A newly installed
33. n Instructions FA REVERSING THE DOOR SWING cont REMOVE THE FRESH FOOD DOOR 3 1 Tape the door shut with masking tape k 3 2 Using a 5 16 hex head socket screwdriver and a 5 16 open end wrench remove the two screws holding the center hinge to the cabinet Lift the center hinge to free its pin from the socket in the top of the door and set hinge and screws aside Be careful not to lose the center hinge spacer and washer 3 3 Remove the tape and tilt the door away from the cabinet Lift the door from the pin in the bottom hinge bracket If the plastic washer sticks to the door bottom put it back on the hinge L 3 4 Set the door outside up on a non scratching surface 14 3 REMOVE THE FRESH FOOD DOOR conr 3 5 Transfer the two screws from the opposite side of the cabinet to the screw holes vacated by the center hinge removal 3 6 Transfer the washer if your model has one to the opposite side 3 7 Take one of the screws removed in step 2 and start it in the outermost screw hole on the opposite side Do not drive it all the way down leave enough space under the screw head for thickness of the bracket 4 REVERSING THE HARDWARE 4 1 Move the bottom hinge bracket and plastic washer from the right side to the left side Switch the hinge pin to the opposite side of the bracket Plastic Washer Bracket Installation Instructions 4 REVERSING T
34. om the original filter cartridge purchase date of the refrigerator GE PROFILE MODELS ONLY Five Years Any part of the sealed refrigerating system the compressor condenser evaporator GE Profile models only and all connecting tubing which fails due to a defect in materials or workmanship From the date of the During this limited five year sealed refrigerating system warranty GE will also provide original purchase free of charge all labor and related service to replace the defective part in the sealed refrigerating system What GE Will Not Cover Service trips to your home to teach you how to use Replacement of the water filter cartridge if included the product due to water pressure that is outside the specified inprop installation delivervotanain tenance operating range or due to excessive sediment in the water supply Failure of the product if it is abused misused or used for other than the intended purpose r used commercially Replacement of the light bulbs if included or water filter cartridge if included other than as noted above Les Of Toad due te Spounee Damage to the product caused by accident fire floods Replacement of house fuses or resetting of circuit or acts of God RES Incidental or consequential damage caused by possible Damage caused after delivery defects with this appliance Product not accessible to provide required service EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive
35. orrect water hammer before installing the water supply line to the refrigerator To prevent burns and product damage do not hook up the water line to the hot water line If you use your refrigerator before connecting the water line make sure the feeler arm is in the STOP up position Do not install the icemaker tubing in areas where temperatures fall below freezing When using any electrical device such as a power drill during installation be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock or is battery powered All installations must be in accordance with local plumbing code requirements WHAT YOU WILL NEED Copper or GE SmartConnect Refrigerator Tubing kit 1 4 outer diameter to connect the refrigerator to the water supply If using copper be sure both ends of the tubing are cut square To determine how much tubing you need measure the distance from the water valve on the back of the refrigerator to the water supply pipe Then add 8 2 4 m Be sure there is sufficient extra tubing about 8 2 4 m coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation WHAT YOU WILL NEED CONT TM GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 6 1 8 m WX08X10006 15 4 6 m WX08X10015 25 7 6 m WX08X10025 Be sure that the kit you
36. own individual electrical outlet which has a voltage rating that matches the rating plate This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires Never unplug your refrigerator by pulling on the power cord Always grip plug firmly and pull straight out from the outlet Repair or replace immediately all power cords that have become frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either end When moving the refrigerator away from the wall be careful not to roll over or damage the power cord MESURES DE SECURITE IMPORTANTES LISEZ D ABORD TOUTES LES DIRECTIVES ef Vile 7 Sf VEUILLEZ LIRE ET SUIVRE ATTENTIVEMENT CES MESURES DE S CURIT AVERTISSEMENT RACCORDEMENT LECTRIQUE RE Ne coupez ni retirez en aucun cas la troisi me broche mise la terre de la fiche du cordon d alimentation Pour votre s curit cet appareil doit tre correctement mis la terre r 4 ON Le cordon d alimentation de cet appareil est muni d une fiche 3 broches mise la terre qui se branche dans une prise murale ordinaire 3 alv oles mise la terre pour r duire au minimum les risques de chocs lectriques Faites examiner la prise de courant et le circuit par un lectricien qualifi pour vous assurer que la prise est correctement mise la terre
37. product repair as provided in this Limited Warranty Any implied warranties including the implied warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law IMPORTANT Keep this warranty and your bill of sale as proof of original purchase and purchase date Please have serial number and model number available when calling for service Mabe Service is available coast to coast If further help is needed concerning this warranty contact Manager Consumer Relations Mabe Canada Inc Consumer Service 1 Factory Lane Suite 310 Moncton New Brunswick E1C 9M3 1 800 561 3344 Staple your receipt here Proof of the original purchase date is needed to obtain service under the warranty Consumer Product Ownership Registration Dear Customer Thank you for purchasing our product and thank you for placing your confidence in us We are proud to have you as a customer Follow these three steps to protect your new appliance investment omplete and mail After mailing the your Consumer egistration below Product Ownership store this document Registration today in a safe place It Have the peace of contains information mind of knowing we you will need should can contact you in you require service the unlikely event of Our service number is a safety modification 800 GE CARES 800 432 2737 ead your Owner s anual carefully It will help you operate your new
38. refrigerator may take 12 to 24 hours to begin making ice There are 2 types of icemakers Power Switch Icemaker Green Power Light Feeler Arm Power switch model NI O A NN RAS SENSES h Feeler Arm in the STOP Feeler Armin up position the ON down position Feeler arm model Automatic Icemaker on some models The icemaker will produce approximately 100 130 cubes in a 24 hour period depending on the freezer compartment temperature room temperature number of door openings and other use conditions If the refrigerator is operated before the water connection is made to the icemaker move the feeler arm to the STOP up position When the refrigerator has been connected to the water supply move the feeler arm to the ON down position The icemaker will fill with water when it cools to 15 F A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes Once the icemaker starts to make ice it may take up to 48 hours to fill the bin depending on the temperature settings and number of door openings You will hear a buzzing sound each time the icemaker fills with water Throw away the first few batches of ice to allow the water line to clear Be sure nothing interferes with the sweep of the feeler arm To replace Lower the frame until it rests on the supports at each side and back 2 Replace the glass cover pushing its rear edge firmly into the rear frame
39. se them to break Handle glass shelves carefully Bumping tempered glass can cause it to shatter Do not wash any plastic refrigerator parts in the dishwasher Condenser There is no need for routine condenser cleaning in normal home operating environments However in environments that may be particularly dusty or greasy the condenser should be cleaned periodically for efficient refrigerator operation Cleaning the condenser coils To clean the condenser turn the temperature control dial to 0 Sweep away or vacuum up dust For best results use a brush specially designed for this purpose It is available at most appliance parts stores 8 Moving the Refrigerator Be careful when moving the refrigerator away from the wall All types of floor coverings can be damaged particularly cushioned coverings and those with embossed surfaces Turn the leveling legs at each front corner of the refrigerator counterclockwise until the rollers support the refrigerator Pull the refrigerator straight out and return it to position by pushing it straight in Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator When pushing the refrigerator back make sure you don t roll over the power cord or icemaker supply line on some models After rolling the refrigerator back into place turn the legs clockwise until the legs again bear the weight of the refrigerator Light Bulb Replacement
40. side diameter of 5 32 at the point of connection to the COLD WATER LINE Saddle type shutoff valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes Installation Instructions SHUT OFF THE MAIN WATER SUPPLY AND UNPLUG REFRIGERATOR Turn on the nearest faucet counterclockwise long enough to clear the line of water DRILL THE HOLE FOR THE VALVE Choose a location for the valve that is easily accessible It is best to connect into the side of a vertical water pipe When it is necessary to connect into a horizontal water pipe make the connection to the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe Drill a 1 4 hole in the water pipe even if using a self piercing valve using a sharp bit Remove any burrs resulting from drilling the hole in the pipe Take care not to allow water to drain into the drill Failure to drill a 1 4 hole may result in reduced ice production or smaller cubes FASTEN THE SHUTOFF VALVE Fasten the shutoff valve to the cold water pipe with the pipe clamp Tighten the clamp screws until the sealing washer begins to swell NOTE Do not overtighten or you may crush the tubing i Washer Saddle Type _ 4A Shutoff Valve Water Pipe NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal
41. sure to leave these instructions with the Consumer Note to Consumer Keep these instructions for future reference Skill level Installation of this appliance requires basic mechanical skills Completion time Refrigerator Installation 15 minutes Reversing the Door Swing 1 hour Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty WATER SUPPLY TO THE ICEMAKER on some models If the refrigerator has an icemaker it will have to be connected to a cold water line A water supply kit containing copper tubing shutoff valve fittings and instructions is available at extra cost from your dealer by visiting our Website at ge com in Canada at www geappliances ca or from Parts and Accessories 1 800 661 1616 REFRIGERATOR LOCATION Do not install the refrigerator where the temperature will go below 60 F 16 C because it will not run often enough to maintain proper temperatures e Install it on a floor strong enough to support it fully loaded CLEARANCES Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides 3 4 19 mm Top 1 25 mm Back 1 25 mm ROLLERS AND LEVELING LEGS Leveling legs near each front corner of the refrigerator are adjustable They firmly position the refrigerator and prevent it from moving when the doors are open
42. ven if they will sit for just a few days If you are getting rid of your old refrigerator please follow the instructions below to help prevent accidents All refrigeration products contain refrigerants which under federal law must be removed prior to product disposal If you are getting rid of an old refrigeration product check with the company handling the disposal about what Before You Throw Away Your Old to do Refrigerator or Freezer Take off the doors Leave the shelves in place so that children may not easily climb inside USE OF EXTENSION CORDS Because of potential safety hazards under certain conditions we strongly recommend against the use of an extension cord However if you must use an extension cord it is absolutely necessary that it be a UListed in the United States or a CSA certified in Canada 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts A DANGER RISQUES POUR LES ENFANTS COMMENT VOUS DEBARRASSER a CONVENABLEMENT DE VOTRE ANCIEN REFRIGERATEUR Les enfants pris au pi ge ou morts d asphyxie R frig rants sont toujours d actualit Les r frig rateurs abandonn s sont toujours aussi dangereux m me si on n attend que quelques jours pour s en d barrasser Si vous ne gardez pas votre ancien r frig rateur veuillez suivre les directives ci dessous afin de pr
43. venir les accidents Tous les appareils de r frig ration contiennent des r frig rants qui conform ment aux lois f d rales doivent tre enlev s avant toute limination de l appareil Si vous vous d barrassez de vieux appareils de r frig ration v rifiez aupr s de la soci t qui s occupe de Avant de vous d barrasser de votre ancien leur limination ce que vous devez faire r frig rateur ou cong lateur D montez les portes Laissez les clayettes en place afin d emp cher les enfants de grimper l int rieur CORDONS PROLONGATEURS Nous vous recommandons fortement de ne pas utiliser de cordons prolongateurs a cause des risques potentiels qu ils pr sentent dans certaines conditions Toutefois si vous d cidez d utiliser tout de m me un cordon prolongateur il est absolument n cessaire qu il s agisse d un cordon 3 fils avec mise a la terre pour appareils lectrom nagers homologu UL aux Etats Unis ou certifi CSA au Canada pourvu d une fiche et d une prise mises la terre de 15 amp res minimum et de 120 volts IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING ge com A WARNING Use this appliance only for its intended purpose as described in this Owner s Manual Vis SPz SAFETY PRECAUTIONS TON re When using electrical appliances basic safety precautions should be followed including the following This refrigerator must be properly installed Be careful c
44. wrench Overtightening may cause leaks Fasten the tubing into the clamp provided to hold it in a vertical position You may need to pry open the clamp Tubing Clamp 12 EX INSTALLING THE WATER LINE cont TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak 711 PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall Push the refrigerator back to the wall START THE ICEMAKER On power switch models set the icemaker power switch to the fon position On feeler arm models move the feeler arm to the ON down position The icemaker will not begin to operate until it reaches its operating temperature of 15 F 9 C or below It will then begin operation automatically Power switch Power switch model os fa Feeler Arm in the es Oe STOP up position X Feeler Arm in the ON down position Feeler arm model NOTE In lower water pressure conditions the water valve may turn on up to 3 times to deliver enough water to the icemaker Installation Instructions FA REVERSING THE DOOR SWING IMPORTANT NOTES When reversing the door swing Read the instructions all the way through before starting Handle parts carefully to avoid scratching paint e Set screws down by their related parts to avoid using them in the wrong places e Provide a non scratching work sur
45. y driven into the outermost hole Insert the remaining screw then tighten both screws securely 6 2 Re hang the freezer door 6 2 1 Lower the freezer door onto the center hinge pin Be sure the washer and spacer are in place on the pin Center Hinge Pin Plastic Washer and Spacer Tilt the door toward the cabinet lifting the top hinge so the pin fits into the socket on the top of the door p SS Make sure the door is slightly above the top of the cabinet and the gap between the doors is even across the front Tighten the top hinge screws Do not overtighten these screws tighten them until they are just snug then turn them another one half turn Normal operating sounds Q E The new high efficiency compressor may run HUMMM faster and longer than WHOOSH your old refrigerator and you may hear a high pitched hum or pulsating sound while it is operating and use newer technology E You may hear a whooshing sound when the doors close This is due to pressure equalizing within the refrigerator ge com Newer refrigerators sound different from older refrigerators Modern refrigerators have more features Do you hear what hear These sounds are normal WHIR E You may hear the fans spinning at high speeds This happens when the refrigerator is first plugged in when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments The
Download Pdf Manuals
Related Search