GE 131892900 Clothes Dryer User Manual
Contents
1. Safety Instructions Care and Cleaning A S 3 rvice Customer Se Installing the dryer cont Reversing the Dryer Door Swing Open the dryer door Remove the 4 hinge hole plugs or screws from the left side of door opening Place nearby for future installation NOTE You may need a plastic knife to help pull out the plugs Be careful not to scratch the paint 2 Remove the four screws that secure the door hinges to the dryer front panel NOTE Remove 1 screw from each of the 2 hinges first Hold the door firmly before removing the last 2 screws Rotate the door 180 and reinstall the door hinges to the dryer front panel with the 4 screws Install the 4 hinge hole plugs or screws that were removed in step 1 into the open screw holes on the right side of the door opening 16 Remove 4 screws one from each hinge first Countdown Display DCD models only The countdown display shows the remaining timer cam pre installed in the coin box If the timer operating time as well as the current drying cycle cam is modified for another operating duration the The display board is configured for a 45 minute dry dipswitches on the display board should be set as time at the factory to correspond with the 45 minute follows suon nnsuj Ajajes ON 9 pue 2189 I buiuea NOTE This display does not accumulate time See the following examples2. Installing the dryer cont Mobile Home Installation Dryer MUST be exhausted outside outdoors not beneath the mobile home using metal ducting that will not support combustion Metal ducting must be 4 10 16 cm in diameter with no obstructions Rigid metal duct is preferred If dryer is exhausted through the floor and area beneath the mobile home is enclosed the exhaust system MUST terminate outside the enclosure with the termination securely fastened to the mobile home structure Safety Instructions When installing a gas dryer into a mobile home a provision must be made for outside make up air This provision is to be not less than twice the area of the dryer exhaust outlet This dryer MUST be fastened to the floor Mobile Home Installation Kit Pub No 14 D346 33 is available from your dealer See the Exhaust System Requirements section for other important venting information Care and Cleaning Rough In Dimensions 26 7 8 68 3 A S 5 5 4 Electrical connection 2 9 16 6 5 cm 13 1 2 43 5 8 34 4 cm 110 7 cm 36 3 3 4 9 5 cm 3 8 0 96 cm Dia gas pipe 1 2 54 cm REAR VIEW rvice Customer Se 12 91 5 cm Installation MUST conform to current Manufactured Home Construction amp Safety Standard which is a Federal Regulation Title 24 CFR Part 32 80
3. Remove the green neutral ground wire from the st SI green ground screw located above the terminal block Typical 4 Black 240V conductor ypical White neutral receptacle 4 conductor cord Red 240V Green ground Thread UL approved 30A 240V 4 10 AWG minimum copper conductor power cord through the strain relief Attach the green power cord ground wire to the cabinet with the green ground screw A Attach the white neutral power cord conductor from the power cord and the green ground wire from the dryer harness to the silver colored center terminal on the terminal block Tighten the screw securely Attach the red and black power cord conductors to the outer brass colored terminals on the terminal block Green power cord ground wire Green ground screw Green neutral ground wire Tighten nut to Red these threads mounting bracket WARNING Do not make a sharp bend or crimp wiring conductor at the connections Tighten the screws securing the cord restraint firmly against the power cord 9 Tighten the strain relief nut securely so the strain relief does not turn Reinstall the terminal block access cover Cy Gas Connection for Gas Dryers Remove the shipping cap from gas pipe at the rear of the dryer NOTE DO NOT connect the dryer to LP gas service without converting the gas valve An LP conversion kit Pub No 14 A038 MUST be installed by a qualifie
4. suon nnsuj Ajajes 2 pue 2189 buiuea na A A S n S N 2 991149 Safety Instructions Care and Cleaning ZA S 3 3 S rvice Customer Se IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING A WARNING YOUR LAUNDRY AREA Keep the area underneath and around your appliances free of combustible materials such as lint paper rags chemicals gasoline and other flammable vapors and liquids Keep the floor around your appliances clean and dry to reduce the possibility of slipping Keep area around the exhaust opening and surrounding areas free from the accumulation of lint dust and dirt DO not obstruct the flow of ventilating air Do not stack or place laundry or throw rugs against the front or back of the dryer WHEN USING YOUR DRYER Never reach into the dryer while the drum is moving Before loading unloading or adding clothes wait until the drum has completely stopped Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room DO NOT OPERATE THE DRYER WITHOUT THE LINT FILTER IN PLACE Do not wash or dry articles that have been cleaned in washed in soaked in or spotted with combustible or explosive substances such as wax oil paint gasoline degreasers dry cleaning solvents kerosene etc which may ignite or explo
5. bracket with a nut Finger tighten the nut only at this time Thread UL approved 30A 240V 3 10 AWG minimum copper conductor power cord through the strain relief Green ground screw Green neutral ground wire Tighten nut to these threads Use copper Power cord conductors only Strain relief mounting bracket Attach the power cord neutral center wire conductor to the silver colored center terminal on the terminal block Tighten the screw securely Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block Tighten both screws securely A WARNING Do not make a sharp bend or crimp wiring conductor at connections 6 Reattach the strain relief mounting bracket to the back of the dryer with one screw Tighten screw securely Tighten the screws securing the cord restraint firmly against the power cord Tighten the strain relief nut securely so that the strain relief does not turn 9 Reinstall the terminal block access cover 4 Wire System for Electric Dryers MUST be used for Mobile Home Installations Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner Install UL approved strain relief in the entry hole of the mounting bracket Use a strain relief which attaches to the mounting bracket with a nut Finger tighten the nut only at this time
6. bags pillows etc that may melt or burn Some rubber materials when heated can under certain circumstances produce fire by spontaneous combustion Do not store plastic paper or clothing that may burn or melt on top of the dryer during operation E Garments labeled Dry Away from Heat or Do Not Tumble Dry such as life jackets containing Kapok must not be put in your dryer DO not dry fiberglass articles in your dryer Skin irritation could result from the remaining particles that may be picked up by clothing during subsequent dryer uses 10 minimize the possibility of electric shock unplug this appliance from the power supply or disconnect the dryer at the distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning DO not spray any type of aerosol into on or near dryer at any time DO not place items exposed to cooking oils in your dryer Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire Never attempt to operate this appliance if itis damaged malfunctioning partially disassembled or has missing or broken parts including a damaged cord or plug The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician See the Care and Cleaning section Do not use any type of spray cleaner when clea
7. knife Phillips head or 1 square screw driver CAUTION To prevent damage do not use the control panel as a means to pick up or move the dryer Return the dryer to an upright position Adjust the leveling legs to match the washer height The dryer must be level and rest firmly on all four leveling legs suon nnsuj Ajajes J9 pue 2189 buiuea n A 5 gt 3 a N 1 WOJSNI Safety Instructions Care and Cleaning Y S 3 Z rvice Customer Se Electrical requirements Read these instructions completely and carefully _ Electrical Connection Information for Electric Dryers WARNING To reduce the risk of fire electric shock or personal injury e DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE e THIS APPLIANCE MUST BE PROPERLY GROUNDED This dryer must be electrically grounded in accordance with local codes and ordinances or the absence of local codes in accordance with the NATIONAL ELECTRICAL CODE ANSI NFPA NO 70 Electrical Requirements This dryer must be connected to an individual branch circuit protected by the required time delay fuses or circuit breakers 208V or 240V installation 30 amps e Use copper conductors only e If the electric supply does not meet the above specifications call a licensed electrician NOTE A wiring diagram is located inside the control pane
8. of 90 turns 60 18 28 m 48 14 63 m 0 40 12 19 ch 32 9 75 m 3 32 975m 24 731 28 853m 16 487m Exhaust Direction All dryers shipped from the factory are set up for rear exhausting However on ELECTRIC DRYERS exhausting can be on the right or left side of the cabinet or the bottom of the dryer On GAS DRYERS exhausting can be on the right side of the cabinet or the bottom of the dryer Directional exhausting can be accomplished by installing Exhaust Kit Pub No 14 A018 available through your parts distributor Follow the instructions supplied with the kit Use only metal ducting inside the dryer cabinet Vig z Gas Supply Requirements INSTALL MALE FITTINGS IN CORRECT DIRECTION e DO NOTassemble the ductwork with fasteners that extend into the duct They will serve as collection points for lint e Ductwork which runs through an unheated area or is near an air conditioning duct should be insulated to reduce condensation and lint build up MAXIMUM LENGTH of 4 10 2 cm Dia FLEXIBLE METAL DUCT PREFERRED VENT HOOD TYPE 4 10 2 cm Louvered Number of 90 turns 17 22 6 71 m 14 4 27 m O2 14 4 27 m 3 not recommended INCORRECT EXHAUST DUCT LOCATING DIMENSIONS 5 7 8 Same as other side 7 3 3 4 9 5 an tee 9 5 cm Pa D Replace brass connecting pipe that is not plastic coated Stainless
9. of 18 45 7 cm above the floor Failure to do so can result in death explosion fire or burns Provide an access for inspection and cleaning of the exhaust system especially at turns Inspect and clean at least once per year Do not obstruct incoming or exhausted air The following directions must be followed Use the shortest length possible Stretch the duct to its maximum length e Do not crush or collapse e Never use transition duct inside the wall flooring ceiling or inside the dryer e Avoid resting the duct on sharp objects Venting must conform to local building codes suonangsu Ajajes 2 pue 2189 buiuea n a S a A VW 2 991149 Safety Instructions Care and Cleaning A S 5 rvice Customer Se Installing the dryer Exhaust Ducting Length The exhaust system should be inspected and cleaned at least once a year with normal usage The more the dryer is used the more often you should check the exhaust system and vent hood for proper operation If roof vents or louvered plenums are used they must be equivalent to a 4 dampered wall cap in regard to resistance to airflow prevention of back drafts and maintenance required to prevent clogging MAXIMUM LENGTH of 4 10 2 cm Dia RIGID METAL DUCT PREFERRED VENT HOOD TYPE 4 10 2 cm Louvered Number
10. steel or plastic coated brass MUST be used WARNING Never reuse old flexible connectors The use of old flexible connectors can cause gas leaks and personal injury Always use NEW flexible connectors when installing a gas appliance Installation MUST conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 latest edition The gas supply line should be of 1 2 1 27 cm rigid pipe If codes allow flexible metal tubing may be used to connect your dryer to the gas supply line The tubing MUST be constructed of stainless steel or plastic coated brass 10 The gas supply line MUST have an individual shutoff valve A 1 8 0 32 cm NPT minimum plugged tapping accessible for test gauge connection MUST be installed immediately upstream of the gas supply connection to the dryer 8 The dryer and its individual shutoff valve MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1 2 psig 3 45 kPa The dryer MUST be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 45 kPa Location of Your Dryer Do Not Install the Dryer Do not install the dryer in an area exposed to dripping water or outside weather conditions Do n
11. transition venting between the dryer and wall connection only The use of this ducting will affect drying time If flexible transition duct is necessary only UL listed duct identified for use with clothes dryers is approved The dryer exhaust system MUST BE EXHAUSTED TO THE OUTSIDE DO NOT allow combustible materials for example clothing draperies curtains paper to come in contact with exhaust system A The dryer MUST NOT be exhausted into a gas vent chimney a wall a ceiling a common duct with a kitchen exhaust or any concealed space of a building which can accumulate lint resulting ina fire hazard A DO NOT exceed the length of duct pipe or number of elbows allowed in the Maximum Length charts Lint can accumulate in the exhaust system plugging the system and creating a fire hazard as well as increasing drying times A DO NOT screen the exhaust ends of the vent system nor use any screws or rivets to assemble the exhaust system Lint can become caught in the screen on the screws or rivets clogging the duct work and creating a fire hazard as well as increasing drying times Use an approved vent hood to terminate the duct outdoors and seal all joints with duct tape All male duct pipe fittings MUST be installed downstream with the flow of air A EXPLOSION HAZARD Do not install the dryer where gasoline or other flammables are kept or stored If the dryer is installed in a garage it must be a minimum
12. MINENT LOCATION 1 Instructions to follow if the user smells gas Contact your local gas supplier for information to be displayed 2 Instructions concerning flammable materials as follows FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance California Safe Drinking Water and Toxic Enforcement Act This act requires the governor of California to publish a list of substances known to the state to cause cancer birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances Gas appliances can cause minor exposure to four of these substances namely benzene carbon monoxide formaldehyde and soot caused primarily by the incomplete combustion of natural gas or LP fuels Properly adjusted dryers will minimize incomplete combustion Exposure to these substances can be minimized further by properly venting the dryer to the outdoors PROPER INSTALLATION This dryer must be properly installed and located in accordance with the Installation Instructions before it is used Properly ground dryer to conform with all governing codes and ordinances Follow details in the nstallation Instructions section Install or store where it will not be exposed to temperatures below freezing or exposed to the weather Connect to a properly rated protected and sized power supply circuit to avoid el
13. NG Use copper receptacles only NOTE Dryers operating on 208 volt power supply will have longer drying times than those operating on 240 volt power supply A wiring diagram is located inside the control panel For a permanently connected electric dryer The dryer MUST be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance For a cord connected gas dryer This dryer is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle Do not cut or remove the grounding prong from this plug suon nnsuj Ajajes 2 pue 2189 buiuea n a DI gt Q VW 2 Safety Instructions Care and Cleaning Y S S rvice Customer Se Installing the dryer cont 14 3 Wire System for Electric Dryers DO NOT use for Mobile Home Installations Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner Install a UL approved strain reliefinto the power cord entry hole of the mounting bracket Use a strain relief which attaches to the mounting
14. Owners Manual amp Installation Instructions Commercial Dryers DCB330E DCB330G DCD330E DCD330G Y www geappliances com Part No 175D1807P295 Pub No 49 90028 10 99 JR 131892900 Safety Instructions Care and Cleaning S 3 rvice Customer Se Safety Instructions Safety Precautions 3 5 Care and Cleaning Care and Cleaning 6 Installation Instructions Preparing to Install Your Dryer Electrical Requirements 8 Exhausting the Dryer 9 10 Gas Supply Requirements 10 Location of Your Dryer 17 Mobile Home Installation 12 Electrical Installation for Electric Dryers 13 14 Gas Connection for Gas Dryers 15 Reversing the Door Swing 16 Countdown Display 17 Customer Service Warranty Back Cover Congratulations You Are Now Part of Our Family Welcome to our family We re proud of our quality products and we are committed to providing dependable service You ll see it in this easy to use Owner s Manual and you ll hear it in the friendly voices of our customer service department Best of all you ll experience these values each time you use your dryer That s important because your new dryer will be part of your family for many years And we hope you will be part of ours for a long time to come We thank you for buyin
15. and all implied warranties of merchantability and caused by possible defects with this appliance fitness for a particular purpose are hereby excluded Care and Cleaning This warranty is extended to the original purchaser and any succeeding owner for products purchased for commercial use within the USA In Alaska the warranty excludes the cost of shipping to your place of business Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 S rvice Customer Se 20 Printed in the United States
16. d gas technician 2 Connect a 1 2 1 27 cm LD semi rigid or approved pipe from gas supply line to the 3 8 0 96 cm pipe located on the back of the dryer Use a 1 2 to 3 8 1 27 cm to 0 96 cm reducer for a connection Apply an approved thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections Before Operating the Dryer Connect the exhaust duct to outside exhaust system Use duct tape to seal all joints With the dryer in its final position adjust one or more of the legs until the dryer is resting solidly on all four legs Place a level on top of the dryer THE DRYER MUST BE LEVEL AND RESTING SOLIDLY ON ALL FOUR LEGS Turn the lock nuts on each of the four legs up toward the base of the dryer and snug with a 1 2 open end wrench Plug the power cord into a grounded outlet NOTE Check to ensure the power is off at circuit breaker fuse box before plugging the power cord into the outlet Turn on the power at the circuit breaker fuse box Replacement Parts Open the shutoff valve in the gas supply line Test all connections by brushing on a soapy water solution CAUTION NEVER TEST FOR GAS LEAKS WITH AN OPEN FLAME NOTE On gas dryers before the burner will light it is necessary for the gas line to be bled of air If the burner does not light within 45 seconds the first time the dryer is turned on the safety switch will shut the burner off If this happens tu
17. de Do not add these substances to the wash water Do not use or place these substances around your washer or dryer during operation Any article on which you have used a cleaning solvent or that contains flammable materials such as cleaning cloths mops towels used in beauty salons restaurants or barber shops etc must not be placed in or near the dryer until solvents or flammable materials have been removed There are many highly flammable items used in homes such as acetone denatured alcohol gasoline kerosene some household cleaners some spot removers turpentines waxes wax removers and products containing petroleum distillates The laundry process can reduce the flame retardancy of fabrics To avoid such a result carefully follow the garment manufacturer s care instructions Close supervision is necessary if this appliance is used by or near children Do not allow children to play on with or inside this or any other appliance Keep all laundry aids such as detergents bleaches etc out of the reach of children preferably in a locked cabinet Observe all warnings on container labels to avoid injury Never climb on or stand on the dryer top Do not install or store this appliance where it will be exposed to the weather Do not dry articles containing rubber plastic or similar materials such as padded bras tennis shoes galoshes bath mats rugs bibs baby pants plastic
18. e that there is notwildlife birds insects etc nesting inside the duct or hood Have a qualified technician vacuum the lint from the dryer once a year Care and Cleaning S z S a rvice Customer Se Preparing to install your dryer Read these instructions completely and carefully WARNING This dryer must be exhausted to the outdoors using only rigid metal or flexible metal 4 diameter ductwork for inside the dryer cabinet or exhausting Never use plastic or other combustible ductwork See Exhausting section This appliance must be properly grounded and installed as described in these nstallation Instructions Do not install or store appliance in an area where it will be exposed to water weather See Location of Your Dryer section The National Fuel Gas code restricts installations of gas appliances in garages They must be 18 Electric Dryer Channel lock pliers adjust leveling legs E 1 2 open end wrench lock leveling legs Carpenters level Rigid or flexible metal 4 10 2 cm duct Duct tape Vent hood 1 4 nut driver remove terminal block access cover and install cord Flat or straight blade screwdriver may be needed for cord strain relief E UL approved 30A 240V 3 wire 10 AWG minimum conductor power cord For a mobile home installation a UL approved 30A 240V 4 wire 10 AWG minim
19. ectrical overload Remove all sharp packing items and dispose of all shipping materials properly In fulfilling the specific needs of different commercial installations the purchaser of this dryer may wish to locate the coin box and controls in any of a number of locations The responsibility for the proper performance of this work lies solely with the purchaser It should be done by properly trained and qualified personnel and in accordance with local code requirements Any coin box or similar device added to the dryer either electrically or mechanically should be properly grounded Remove any accumulated time by manually rotating timing cam in the coin box counterclockwise until switch shuts off Apply a slight additional counterclockwise pressure to further seat drive Make certain not to turn cam past switch shut off position Otherwise one increment of time will be gained Switches are off when the plastic switch actuating arm inner is down and all 3 switch buttons are depressed Exhaust Ducting This dryer MUST be exhausted to the outside Use only rigid metal or flexible metal 4 diameter ductwork inside the dryer cabinet or for exhausting to the outside USE OF PLASTIC OR OTHER COMBUSTIBLE DUCTWORK CAN CAUSE A FIRE PUNCTURED DUCTWORK CAN CAUSE A FIRE IF IT COLLAPSES OR BECOMES OTHERWISE RESTRICTED IN USE OR DURING INSTALLATION Follow details in the nstallation Instructions section 3
20. g our product We appreciate your purchase and hope you will continue to rely on us whenever you need quality appliances A Service Partnership nl 2 IMPORTANT 2 N Staple sales slip cancelled check here Proof of the original purchase date is needed to obtain service under the warranty FOR YOUR RECORDS gt Write the model and serial numbers here They are on the label on the front of the left side of the door opening READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your dryer properly Just a little preventive care on your part can save you a great deal of time and money over the life of your dryer PROPER VENTING For the best drying performance the dryer needs to be properly vented The dryer will use more energy and run longer if it is not vented to the specifications outlined in the Exhausting section in the Installation Instructions IF YOU NEED SERVICE If you need service contact your General Electric Commercial Laundry distributor IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING A WARNING For your safety the information tn this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or death Installation and service must be performed by a qualified installer service agency or the gas supplier FOR GAS DRYERS YOU MUST POST IN A PRO
21. l Flectrical Connection Information for Gas Dryers WARNING To reduce the risk of fire electric shock or personal injury e DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE e DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD This dryer must be electrically grounded in accordance with local codes and ordinances or in the absence of local codes in accordance with the NATIONAL ELECTRICAL CODE ANSI NFPA NO 70 Electrical Requirements This dryer must be supplied with 120V 60 Hz and connected to an individual properly grounded brand circuit protected by a 15 or 20 amp circuit breaker or time delay fuse If the electric supply provided does not meet the above specifications it is recommended that a licensed electrician install an approved outlet Ensure proper ground exists before use External Ground if required An external ground wire not provided which meets local codes may be added by attaching it to the green ground screw on the rear of the dryer in the upper left hand corner and to grounded metal cold water pipe or other established ground Attach ground wire obtain locally NOTE A wiring diagram is located inside the control panel Exhausting the dryer Exhaust System Requirements Use only 4 10 2 cm diameter minimum rigid metal duct for best performance or flexible metal duct Use approved ven
22. ning dryer interior Hazardous fumes or electrical shock could occur If yours is a gas dryer it is equipped with an automatic electric ignition and does not have a pilot light DO NOT ATTEMPT TO LIGHT WITH A MATCH Burns may result from having your hand in the vicinity of the burner when the automatic ignition turns on WHEN NOT USING YOUR DRYER Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling Place the cord away from traffic areas so it will not be stepped on tripped over or subjected to damage Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically recommended in this Owner s Manual or in published user repair instructions that you understand and have the skills to carry out You may wish to soften your laundered fabrics or reduce the static electricity in them by using a dryer applied fabric softener or an anti static conditioner We recommend you use either a fabric softener in the wash cycle according to the manufacturer s instructions for those products or try a dryer added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer Service or performance problems caused by use of these products are the responsibility of the manufacturers of those products and are not covered under the warranty to this appliance Before discarding a dr
23. of display possibilities DIPSWITCH SETTING min COIN SLIDE ACTUATIONS DISPLAY READING min 45 to 1 then 1 for next 45 min then 0 and blank 99 for 21 minutes then 98 to 0 then blank n 9 gt Q gt a S N 2 17 Notes 18 suon nnsuj Ajajes pue suon nnsuj uonejjesuj 991 49S J9UIO SNI Safety Instructions Care and Cleaning Installation Instructions Customer Service ig GE Commercial Dryer Warranty Parts and service are available from your General Electric Commercial Laundry distributor gt For The Period Of GE Will Replace T Three Years Any part of the dryer which fails due to a defect in materials or workmanship except the drop n From the date of the coin meter coin slide mechanism coin vault and locks which are excluded from this warranty original purchase During this limited three year warranty any related service labor and diagnostic calls are not included What GE Will Not Cover Service trips to your place of business to teach youhowto W Replacement of fuses or resetting of circuit breakers at use the product place of business Improper installation Damage to the product caused by accident fire floods or Failure of the product if it is abused misused or used for other than the intended purpose Incidental or consequential damage to personal property E Any
24. of the wall outlet taking into account the length Grounding Requirements DANGER Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded Grounding must be in accordance with local codes and ordinances or in the absence of local codes in accordance with the National Electrical Code ANSI NFPA No 70 For a grounded cord connected electric dryer The dryer MUST be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock by creating a path of least resistance for electrical current Ifyour dryer is equipped with a power supply cord having an equipment grounding conductor and a grounding plug the plug MUST be plugged into an appropriate copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances lf in doubt call a licensed electrician e u__Electrical Installation for Electric Dryers of power cord to be purchased and allowing some slack in the cord Refer to Electrical Requirements in this manual for the proper power cord to be purchased WARNING A UL approved strain relief must be installed onto power cord If the strain relief is not attached the cord can be pulled out of the dryer and can be cut by any movement of the cord resulting in electrical shock A WARNI
25. or when such standard is not applicable with American National Standard for Mobile Homes Correct Do UMMM eli SSW Q N D A I Wt a PN ily 22 TLAS The dryer is designed for use under ANSI Z 21 5 1 lt 1 4 1 2 120 7 cm Door open 90 43 8 11 1 cm Optional vent knockout 27 68 6 3 3 4 9 5 cm SIDE VIEW Servicing Consideration must be given to provide adequate clearances for installation and servicing CAUTION Label all wires prior to disconnection when servicing controls Wiring errors can cause improper and dangerous operation verify proper operation after servicing installation WARNING The following are specific requirements for proper and safe electrical installation of your dryer Failure to follow these instructions can create electrical shock and or a fire hazard WARNING This appliance MUST be properly grounded Electrical shock can result if the dryer is not properly grounded Follow the instructions in this manual for proper grounding WARNING DO NOT use an extension cord with this dryer Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt creating electrical shock and or fire hazard Locate the dryer within reach
26. ot install the dryer in an area where it will come in contact with curtains drapes or anything that will obstruct the flow of combustion and ventilation air Installation in Recess or Closet This dryer MUST be exhausted outdoors No other fuel burning appliance shall be installed in the same closet as the GAS DRYER Your dryer needs the space around it for proper ventilation DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A SOLID DOOR A minimum of 120 square inches 774 2 square cm of opening equally divided at the top and bottom of the door is required Air openings are required to be unobstructed when a door is installed A louvered door with equivalent air openings for the full length of the door is acceptable 60 sq in Gi tf 387 1 sq cm 2 1 j 7 l 7 f 7 f 7 f 7 f 7 d 60 sq in 387 1 sq cm Closet door Do not install the dryer on carpet Floor MUST be solid with a maximum slope of 1 2 54 cm Allow the following clearances for ease of installation FRONT SIDES REAR TOP Alcove 0 0 cm 0 0cm 0 0 15 38 1 cm Closet 17 2 54cm 0 0 0 0cm 15 38 1 cm Closet door ventilation required 2 louvered openings each 60 square inches 387 1 square cm 3 7 6 cm from bottom and top of door 0 0 cm 11 suon nnsuj Ajajes 2 pue 2189 buiuea n a Q gt Q n a S V 2
27. rn the dryer off and wait 5 minutes before making another attempt to light A CAUTION Before operating the dryer make sure the dryer area is clear and free from combustible materials gasoline and other flammable vapors Also see that nothing such as boxes clothing etc obstructs the flow of combustion and ventilation air Run the dryer through a cycle check for proper operation Place these instructions in a location near the dryer for future reference If replacement parts are needed for your dryer contact the source where you purchased your dryer A CAUTION Label all wires prior to disconnection when servicing controls Wiring errors can cause improper and dangerous operation Verify proper operation after servicing A WARNING Destroy the carton and plastic bags after the parts are unpacked Children might use them for play Cartons covered with rugs bedspreads or plastic sheets can become airtight chambers causing suffocation Place all materials in a garbage container or make materials inaccessible to children WARNING The instructions in the manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur Good safe practice and caution MUST be applied when installing operating and maintaining any appliance o suon nnsuj Ajajes 2 pue 2189 buiuea n a 5 gt a a a S S S VN 1 0JSNI
28. t hood which has swing out dampers that open when the dryer is in operation When the dryer stops the dampers automatically close to prevent drafts and the entrance of insects and rodents To avoid restricting the outlet maintain a minimum of 12 30 5 cm clearance between the vent hood and the ground or any other obstruction If all rigid metal duct cannot be used then flexible all metal venting can be used but it will reduce the maximum recommended duct length See Additional Installation Instructions following Correct XQ QQ WARNING The following are specific requirements for proper and safe operation of your dryer Failure to follow these instructions can create excessive drying times and fire hazards DO NOT use plastic flexible duct to exhaust the dryer Excessive lint can build up inside exhaust system and create a fire hazard and restrict air flow Restricted air flow will increase drying times If your present system is made up of plastic duct or metal foil duct replace it with rigid or flexible metal duct Ensure the present duct is free of any lint prior to installing dryer duct Additional Ducting Instructions If all rigid metal duct cannot be used then flexible all metal venting can be used but it will reduce the maximum recommended duct length In special installations when it is impossible to make a connection with the above recommendations then UL listed clothes dryer transition ductmay be used as
29. um conductor power cord is required E UL approved cord strain relief may be supplied with cord Unpacking the Dryer Using the four shipping carton corner posts two on each side carefully lay the dryer on its left side and remove foam shipping pad Foam shipping pad gt Packing lools and Materials Required for Dryer Installation 45 7 cm off the ground and protected from vehicles by a barrier See Location of Your Dryer section The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the National Electrical Code ANSI NFPA 70 The gas service to the dryer must conform with local codes and ordinances or the latest edition of the National Fuel Gas Code ANSI 7223 1 The gas dryer is designed for use under ANSI Z 21 5 1 This dryer is not recommended for commercial applications such as restaurants or beauty salons etc Gas Dryer Channel lock pliers adjust leveling legs E 1 2 open end wrench lock leveling legs Carpenter s level Rigid or flexible metal 4 10 2 cm duct Duct tape Vent hood Flexible stainless steel or plastic coated brass connecting gas tube if allowed by building code Connector for between dryer and flexible tube 3 8 pipe thread on dryer side may be supplied with flexible tube Pipe thread sealer Open end wrenches for flexible tube and connector Door Reversal E Plastic
30. yer or removing it from service remove the dryer door to prevent children from hiding inside Do not tamper with controls Read and follow this Safety Information carefully SAVE THESE INSTRUCTIONS suonangsu Ajajes 2 pue 2189 buiuea n 11 S S A N 1 0JSNI Care and cleaning I sq_ and Cleaning of the Dryer dea Ss The Exterior Wipe or dust any spills or washing The Exhaust Duct Inspect and clean the exhaust compounds with damp cloth Dryer control ducting at least once a year to prevent clogging A g panel and finishes may be damaged by some partially clogged exhaust can lengthen the drying amp laundry pretreatment soil and stain remover time 5 products Apply these products away from the Follow these steps dryer The fabric may then be washed and dried normally Damage to your dryer caused by these Turn off electrical supply by disconnecting the products is not covered by your warranty plug from the wall socket The Lint Filter Clean the lint filter before each Disconnect the duct from the dryer use Run your fingers across the back of the filter to remove lint Do not operate the dryer without the lint filter in place Vacuum the ductwith the hose attachment and reconnect the duct The Exhaust Hood Check with a mirror that the inside flaps of the hood move freely when operating Make sur
Download Pdf Manuals
Related Search