GE 131-10595-2 1-07 JR Music Mixer User Manual
Contents
1. Position the range in front of the opening but slightly to the side in a manner so that a person can enter the opening to wire the range to the house wiring in the junction box 6 Feed wires and conduit through the open hole and snap the conduit fitting into the hole Route the conduit in a manner that will not interfere with the rear wire cover The conduit must be routed below the wire cover A WARNING Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire Use only connectors designed for joining copper to aluminum and follow the manufacturer s recommended procedure closely GENERAL NOTE FOR ALL WIRE NUT APPLICATIONS THE PROPER SIZE WIRE NUT SHALL BE PLACED OVER THE STRIPPED LEADS AND THE WIRE NUT TWISTED UNTIL THE WIRE NUT CAN NOT BE PULLED FROM THE LEADS NO CONDUCTOR SHALL BE EXPOSED IN THE CONNECTION THE EXCEPTION TO THE CONDUCTOR BEING EXPOSED IS THE BARE COPPER GROUND CONNECTION BREAKER OR FUSE SIZE 240V 40 Amps 208V 40 Amps NOTE Check Local Codes for required breaker size Installation Instructions THREE CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a 3 conductor branch circuit if local codes permit Connect the bare oven ground conductor with the crimped neutral white lead to the branch circuit neutral white or gray in color using wire nuts Connect the oven red lead to the branch circuit red lead and the oven blac2. knobs to MED setting to observe that the element glows within 15 seconds Turn the knob off when glow is detected If the glow is not detected within the time limit recheck the range wiring connections If change is required retest again If no change is required have building wiring checked for proper connections and voltage 13 Installation Instructions ALTERNATE CONSTRUCTION PREPARATION A OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall it will require Maintop Filler Kit JXS66XX or Backguard Kit JXS32XX to close the gap NOTE If the countertop is greater than 25 it will show a gap between the backguard and wall or between filler kit and the wall If the countertop is less than 25 a gap will occur between the countertop front and the control panel ends See page 10 Step 3 Wall lt Must be flat Must be gt 30 gt flat smooth cut lt Mustbe leve gt Refer to the Filler or Backguard Kit instructions for Installation details 14 ISLAND INSTALLATION When installing in an island or other non standard location countertop cutout dimensions must be according to page 5 For the anti tip bracket instructions see page 9 In this application do not use Backguard Kit JXS32XX CABINETS OVER THE RANGE LESS THAN 30 If a 30 clearance between cooking surface and overhead combustible material or metal ca
3. Installation Electric Instructions Prop in Range JDS28 JDP39 BEFORE YOU BEGIN e Proper installation is the responsibility of the Read these instructions carefully and installer and product failure due to improper completely y installation is NOT covered under the warranty e NOTE This appliance must be properly IMPORTANT Save these grounded instructions for local inspector s use ATTENTION INSTALLER eIMPORTANT observe all All electric drop in ranges must be hard wired governing codes and ordinances direct wired into an approved junction box A plug and receptacle is NOT permitted on e Note to Installer Be sure to leave these these products instructions with the consumer e Note to Consumer Keep these instructions for future reference PARTS INCLUDED TOOLS YOU WILL NEED Ate Phillips Screwdriver 2 Shoulder Screws 1 8 Drill Bit and for stop device Electric or Hand Drill ere Lower Trim 2 Screws Standard Screwdriver Nut Driver MATERIALS NEEDED Tape Measure ki aes a a AA Junction Box Strain Relief Clamp Wire Nuts AA for 1 2 conduit Straight Edge or Square aE Pencil C em g Ze Safety Glasses Hand or Sabre Saw 31 10595 2 1 07 JR 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY A WARNING For personal safety remove house fuse or open circuit breaker before beginning installation Failu
4. LATION to engage bracket by 1 Wire cover 1 2 min Interior wall gt Wall stud JY Non kit application PE Countertop Maintop Z surface Attachment Position 5 non kit application to Yi Attachment Anti tip bracket anchored to ZZA wall stud is required Attachment to engage bracket by 1 2 min Installation Instructions INSTALL THE RANGE CONT 2 INSTALL STOP SCREW These screws prevent the range from sliding out of position during operation One Screw each side Carefully mark the cabinet for the location of the stop screws Drill 1 8 pilot holes into the cabinet each side of the range Make sure not to drill entirely through the cabinet wall Carefully turn the shoulder screws into the pilot holes until they are tight 10 3 PLACING THE RANGE INTO THE OPENING It is suggested that two people lift the range into place carefully setting the side metal flanges on the edges of the countertop opening Carefully slide the range toward the back of the opening In the last 1 of travel lift the front of the range approx 1 2 to clear the stop screws located in the sides of the cabinet and slide the range until the range is seated Lower front of the range onto countertop Lift and slide range on Countertop Make sure the edge of the countertop fits flush against the end of the Front Control Panel Install
5. ation Instructions 4 CHECK FOR PROPER INSTALLATION OF THE STOP SCREW Look at both sides of the range under the door The stop screws must be located in the notch on the sides of the range and not touch the top of the notch when the range is fully seated on the countertop If the screws do not meet the requirements move the screws to a position that meets these requirements See illustration below Notch in bottom of side trim h Clear e Side X J Lie Shoulder screw 11 5 ATTACH THE LOWER TRIM Attach the lower trim supplied separately with the range to the bottom of the vertical side trim with the 2 screws supplied Lower left corner front frame Attach 1 screw W each side Wee End flange amp tab on lower trim fits inside Top flange side trim T 1 2 wide NJ Installation Instructions INSTALL THE RANGE CONT REPLACING THE OVEN DOOR 9 Push the hinge locks up against the front NOTE The oven door is heavy You may need Le the oven cavity to the locked help lifting the door high enough to slide it Hinge in into the hinge slots Do not lift the door by locked position the handle 6 Lift the oven door by placing one hand on oneal each side The door is eed heavy SO you may need into bottom of help Do not lift the door hinge slot by the handle Close the oven door With the door at the same angle as the 11 CHECK FOR PROPER removal p
6. binets cannot be maintained protect the underside of the cabinets above the cooktop with not less than 1 4 insulating millboard covered with sheet metal not less than 0 0122 thick D CABINET CUTOUT HEIGHT MORE THAN 27 1 2 USE LOWER TRIM KIT Optional Lower Trim to fill space beneath 27 1 2 min requirement see page 4 Use lower Trim Kit JXS96XX Notes 15 Notes 16 Printed in the United States
7. e Remove packing materials Remove labels on door plastic on trims and panel and all tape around the range Installation Instructions PRE INSTALLATION CUTOUT AND REQUIRED CLEARANCES Overall Depth NOTE Drop In Ranges are designed to hang from the countertop only Do not install on a platform or support rails elke instructions Packaged ol alternate appliances inet F min dim intai bet im Must be maintained if Required ween cooking surface and hiii underside of appliance 6 Min From Walls recommended Preformed If cabinets are placed less than Backsplash 30 min above the range see h alternate construction 30 ranges conform to U L requirements for 0 spacing from vertical walls below countertops Allow 1 4 minimum clearance at the back wall above the countertop Wall coverings counters and Pacer cabinets around range must withstand heat up to 200 F generated by the range gt 29 ISen 30 1gryin ax Installation Instructions PREPARE TO INSTALL THE RANGE STANDARD INSTALLATION i I in i i 25 i 23 3 16 l typically I I 1 9 16 min lt 29 15 16 30 1 16 gt smooth cut The Standard Installation of this Drop In Range is to hang by the countertop on the side metal flanges under cooktop This Range must not be installed on a base or sub structure 2 x 4 support If the const
8. k lead to the branch circuit black lead in accordance with local codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING note see page 6 Black Branch circuit Red i Ground and Ti neutral wires i Neutral bare wire white connection knockout NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION e When installing in new construction or e When installing oven in a mobile home or recreational vehicle or e When local codes do not permit grounding through neutral Cut the neutral white lead from the crimp Re strip the neutral white lead to expose the proper length of conductor and connect it to the white or gray branch circuit neutral in accordance with local code using wire nuts Attach the appliance grounding lead green or bare copper in accordance with local codes If the residence grounding conductor is aluminum see WARNING note see page 6 Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING note see page 6 Branch circuit knockout Installation Instructions ELECTRICAL CONNECTIONS CONT Reinstall Junction box cover Do not shorten the flexible conduit The conduit strain relief clamp must be securely attached to the j
9. osition halfway between the closed and broil stop position seat the INSTALLATION OF notch of the hinge arm into the bottom ANTI TIP BRACKET edge of the hinge slot The notch of the hinge arm must be fully seated into the bottom of the slot Lower the oven door and gently apply medium force at the handle end until movement of the range is detected Continue pressing until the Hinge arm anti tip bracket is engaged and movement Bottoin edge stops A small amount of movement is of slot acceptable at the back of the range top but it should be stable and not tip once the anti tip bracket is engaged Hinge notch Open the oven door as far as it will open 12 Installation Instructions 12 FINAL CHECKLIST e Check to make sure the circuit breaker is closed Reset or the circuit fuses are replaced e Be sure power is in service to the building e Check to be sure that all packing materials and tape on metal panel if applicable under control knobs and drawer have been removed 13 OPERATION CHECKLIST e Check to make sure the Clock display is energized If a series of horizontal red lines appear in the display disconnect power immediately Recheck the range wiring connections If change is made to connections retest again If no change is required have building wiring checked for proper connections and voltage It is recommended that the clock be changed if the red lines appear e Push down and turn any one of the four surface
10. re to do so could result in serious injury or death e All rough in and spacing dimensions must be met for safe use of your range e To reduce the risk of burns or fire when reaching over hot surface elements cabinet storage space above the cooktop should be avoided If cabinet storage space is to be provided above the cooktop the risk can be reduced by installing a range hood that protrudes at least 5 beyond the front of the cabinets Cabinets installed above the cooktop must be no deeper than 13 e Be sure your appliance is properly installed and grounded by a qualified technician ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on rating plate Rating Plate is located behind the oven door on the range Rating plate location We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician After installation have the electrician show you where your main range disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your range according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Late
11. ruction of your cabinet cannot provide a 1 4 flat area at the back of the countertop opening consider changing the countertop to accommodate this dimension Range support gs ee Ss ee Counte GE eee PA L Braces secured between the underside of the countertop and the cabinet if required to obtain 1 1 4 minimum thickness two sides 1 Center the 30 wide opening over the adjacent cabinets and mark with a straight edge 2 Using a straight edge mark the back line at 23 3 16 from the front edge of the counter 3 Be careful not to damage the adjacent cabinets while cutting the countertop 4 Remove countertop raised edge if incorporated See illustration on page 4 Installation Instructions ELECTRICAL CONNECTIONS 1 Remove house fuse or open circuit breaker 2 Loosen screws for the junction box cover and rotate out of place or remove the cover 3 Examine the junction box location to determine the best routing of the conduit and select the best available 7 8 diameter knockout Avoid using holes in the top of the junction box to prevent the conduit from interfering with the back of the range 4 Break open the selected knockout by placing a bladed screwdriver on the scored opening in the junction box and striking the screwdriver with a hammer Pliers may be required to complete the removal of the knockout 7 8 knockout Cover rotated from box opening 5
12. st Edition You can get a copy by writing National Fire Protection Association Batterymarch Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new but not existing construction utilize a four conductor connection to an electric range When installing an electric range in new construction a mobile home recreational vehicle or an area where local codes prohibit grounding through the neutral conductor follow the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used Installation Instructions PRE INSTALLATION CHECKLIST e Move Range Indoors In Front of Cabinet Opening e Protect the kitchen floor Flatten and place a piece of the shipping carton in front of the installation location to protect the flooring e Inspect Installation Location Inspect cutout dimensions and location of electrical junction box to be sure it fits within the layout location See page 4 Refer to alternate construction section for the following non standard installations a Counter opening extends to the wall Maintop Filler Kit JXS66XX or Backguard Kit JXS32XX WARNING If you do not use these kits the anti tip bracket must fit under an at
13. tachment to the wall that can withstand a force of 200 Ibs in the upward direction See Step 1 under INSTALL THE RANGE Island Installation To provide an optimum installation the top surface of the countertop must be level and flat lie on the same plane around the 3 sides that are adjacent to range cooktop Proper adjustments to make the top flat should be made or gaps between the countertop and range cooktop may occur Forcing the cooktop to fit may cause excessive gaps To obtain Kits a Visit GE Web Site See page 1 b Call GE Answer Center See page 1 c Contact Dealer Door removal is not a requirement for installation of the product but is an added convenience To remove the door e Open the oven door as far as it will go e Push both hinge locks down toward the door frame Hinge to the unlocked slot position This may require a flat blade screwdriver Hinge ii N unlocked DO NOT LIFT THE DOOR BY THE HANDLE e Place hands on both sides of the door and close the oven door to the removal position This is half way between the broil stop and fully closed e Lift door up and out until the hinge arms clear the slots Hinge clears slot NOTE The oven door is very heavy Be sure you have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches
14. unction box and the flexible conduit must be securely attached to the clamp If the flexible conduit will not fit within the junction box do not install the oven until a clamp of the proper size is obtained NOTE TO ELECTRICIAN The 3 power leads supplied with this appliance are UL recognized for connection to larger gauge household wiring The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire rather than the wire gauge alone Installation Instructions INSTALL THE RANGE 1 INSTALLING THE ANTI TIP Select the proper position for the countertop thickness and move bracket to proper position BRACKET Unit is supplied with bracket in position 1 The anti tip bracket is attached to the back of the Drop In Range It is designed to fit under Q For 3 4 Counter For 3 5 the bottom of the countertop opening at the 7 rear Measure counter thickness at back of 2 For 1 18 3 cm Counter G Alternate cutout to determine correct bracket location For 1 5 Counter shown below Anti tip bracket location rear of range Cooktop __ _ ANTI TIP INSTALLATION Interior wall 1 4 min flat area ___ lt Wall stud Maintop Countertop thickness Anti tip bracket Bottom of ee cid ALTERNATE countertop ANTI TIP INSTAL
Download Pdf Manuals
Related Search