Gateway FPD1750 Computer Monitor User Manual
Contents
1. Hz 11 VESA 1152 x 900 61 81 kHz 65 Hz 12 VESA 1280 x 1024 63 98 kHz 60 Hz 13 VESA 1280 x 1024 79 98 kHz 75 Hz If you do not use the best mode for the monitor the display image may look slightly fuzzy Power management ENERGY STAR As an ENERGY STAR Partner Gateway has determined that this product meets the ENERGY STAR guidelines for energy efficiency This monitor complies with the EPA s International ENERGY STAR Program which is a program designed to encourage manufacturers of computer equipment to build circuitry into their products to reduce energy consumption during time of non use Energy declaration 14 When connected to a computer that supports the VESA Display Power Management Signaling DPMS Protocol the monitor can conserve significant energy by reducing power consumption during periods of non use When your computer goes into the energy saving mode the monitor will then enter the Active Off mode different from total shut down In the Active Off mode the Power LED will still show orange Use these conventions and the power can be reduced to the following levels VESA State LED Indicator Power Consumption On Green 45 W Active Off Orange lt 3W To wake the monitor when it is in Active Off mode move the mouse or press any keyboard key Access the power management options in the Control Panel to change the period of time after which the monitor enters these low power states Maintenance To2. other settings for the monitor The monitor saves changes you make to the settings even if you turn off the monitor SOURCE MENU WLightViewA lt re gt AUTO SELECT N A 4 N N f N f N lt gt Contrast Power button button button and LED SOURCE A V LightView AUTO SELECT button button button m SOURCE Press to switch between analog or digital source signals or switch between computers if you have two computers connected to the monitor m MENU Press to view the OSD Press again to exit A V LightView OSD active Press to select or adjust OSD options OSD inactive Press to access the LightView menu and select a preset viewing mode or customize one of your own Preset modes include optimized settings for text movies or photos in either day or night ambient light levels LIGHT VIEW TEXT MOVIE PHOTO TEXT MOVIE PHOTO USER MODE lt gt Contrast OSD active Press to adjust OSD options OSD inactive Press to adjust the brightness and contrast AUTO SELECT OSD active Press to make a selection in the OSD OSD inactive Press to automatically optimize the monitor s image position clock and phase Power LED Press this button to turn the monitor off and on On screen display options To adjust the OSD settings 4 2 3 4 Press the MENU button The OSD menu opens Use the A and V buttons to highlight a control then press the AUTO SELECT button Use the lt gt A V buttons t
3. the SOURCE button on the front of the monitor to switch between computers For more information about the SOURCE button see External controls on page 7 If the power LED is orange m Make sure that your computer is turned on m Move the mouse or press any key on the keyboard to bring the monitor out of Active Off mode m Restart your computer with the monitor turned on m Make sure that the video cable is not damaged m Check the end of the video cable for any pins that might be bent or pushed in Turn off the monitor and unplug the video cable from the back of your computer Turn the monitor back on and wait for ten seconds If the monitor is functioning correctly a self diagnostic screen appears For more information about connecting the video cable see Connecting the monitor on page 2 Display colors are wrong 16 Press the AUTO SELECT button to automatically adjust the display image to the ideal settings Restart your computer with the monitor turned on Make sure that the video cable is connected securely to the back of the monitor and your computer For more information about connecting the power cord see Connecting the monitor on page 2 Make sure that the video cable is not damaged Check the end of the video cable for any pins that might be bent or pushed in Picture has shadows or ghosts Press the AUTO SELECT button to automatically adjust the display image to the ideal settings Remo
4. the monitor 1 Position your computer and the monitor so you can reach the connections on each 2 Lay the monitor on its back 3 Connect the power cord to the power connector under the bottom of the screen 2 www gateway com 4 If your computer supports analog video blue video connector connect the analog video cable to the blue analog connector under the bottom of the screen OR If your computer supports digital video white video connector connect the digital video cable to the white DVI connector under the bottom of the screen Important Make sure that you only connect one video cable to the monitor and computer The only way to use both connections it to share the M monitor between two computers Use the SOURCE button to change between computers For more information see Adjusting monitor settings on page 7 5 Return the monitor to its upright position 6 Make sure that your computer is turned off www gateway com 7 If you connected the analog video cable to your monitor connect the other end of the cable to the matching blue video port on the back of your computer MU LUI MN OR If you connected the digital video cable to your monitor connect the other end of the cable to the matching white video port on the back of your computer gt NM LU AN N 9 EHE O www gateway com 8 Plug the power cord into a correctly grounded electrical outlet www
5. Gateway User Guide Gateway FPD 1940 Monitor Contents Using Your FPD 1940 Monitor 1 Connecting the MONO a e subi send his bananes dass Lu de dl 2 Starting the MONO scsi canen ie in Be Ra 6 AQJUSTING MIONHOFSELINGS Hua asina a E LEER da 7 EXie al CONUOIS La PG AS A e 7 On screen display options 2 424 cete aaa ad a da pa 8 SONWALE CONMOIS LE seca diabetes Eta ew wad 10 WIGCOMIMOGES RENE od rn DUR A NN beth Manatee hed 13 POWER Management Sas MR MR ee aa ea 14 ENERGY STAR arar a rada ee dp 14 Energy declaran casona ness AAA OA ar a 14 Maintenant xs iti dorin a e ads 15 TIOUDISSROOUNO EL ES rai a E A wes ae ARA 15 NO DOWER ss cui sa sd mardi rada sd dad ai 15 NOFDIEIUTE e cursis star a rs 16 Display colors are WONG tia AA A A an e dada Sit d d 16 Picture has shadows or ghosts seran di ada 17 Color IS MOL UNION e eei aaea re e a Gee ea 17 Image is not sized or centered correctly 17 The monitor has pixels that are always dark or too bright 17 SPECIICAIONS s 44 ci A A ete eid he eS oe ee ee 18 Safety Regulatory and Legal Information 19 www gateway com Gateway Using Your FPD 1940 Monitor cet the monitor Starting the monitor m Maintenance and troubleshooting Adjusting monitor settings m Specifications Connecting the monitor To connect
6. Thin Film Transistor LCD Best screen resolution 1280 x 1024 Display colors Over 16 million colors Power input AC 100 240 V 50 60 Hz 1 0A Power consumption Normal operation 45 W Active Off operation lt 3 W Dimensions 16 25 x 8 78 x 17 13 inches W x D x H 41 28 x 22 30 x 43 50 cm W x D x H Power management Meets EPA ENERGY STAR and VESA DPMS requirements Certifications UL cUL EPA and FCC Class B NOM Many products for Gateway and its subsidiaries are custom engineered by our suppliers to Gateway specifications and may vary from similarly marketed products Gateway Safety Regulatory and Legal Information m Safety information m Regulatory statements m Notices 19 Important safety information Your Gateway system is designed and tested to meet the latest standards for safety of information technology equipment However to ensure safe use of this product it is important that the safety instructions marked on the product and in the documentation are followed Warning Always follow these instructions to help guard against personal injury Q and damage to your Gateway system Setting up your system 20 Read and follow all instructions marked on the product and in the documentation before you operate your system Retain all safety and operating instructions for future use Do not use this product near water or a heat source such as a radiator Set up the system on a stable work surface The product sh
7. d found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a different circuit from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Compliance Accessories The accessories associated with this equipment are shielded video cable These accessories are required to be used in order to ensure compliance with FCC rules FCC declaration of conformity Responsible party Gateway Companies Inc 610 Gateway Drive North Sioux City SD 57049 605 232 2000 Fax 605 232 2023 This device complies with Part 15 of the FCC Rules Operation of this device is subject to t
8. drinking near your system Do not expose the monitor to rain or use near water If the monitor does get exposed to moisture unplug it and allow it to dry for 24 hours Call Gateway Technical Support for advice on whether the monitor is safe to turn back on When the monitor is turned off a small amount of electrical current still flows through the monitor To avoid electrical shock always unplug all power cables and modem cables from the wall outlets before cleaning the system Unplug the system from the wall outlet and refer servicing to qualified personnel if The power cord or plug is damaged Liquid has been spilled into the system The system does not operate properly when the operating instructions are followed The system was dropped or the cabinet is damaged The system performance changes Warning To prevent electric shock never remove the cover No user serviceable parts inside Refer servicing to qualified service personnel Replacement parts and accessories Use only replacement parts and accessories recommended by Gateway Warning Do not use Gateway products in areas classified as hazardous locations Such areas include patient care areas of medical and dental facilities oxygen laden environments or industrial facilities 21 Regulatory compliance statements United States of America Federal Communications Commission FCC Unintentional emitter per FCC Part 15 This device has been tested an
9. e reserved No part of it may be reproduced or transmitted by any means or in any form without prior consent in writing from Gateway The information in this manual has been carefully checked and is believed to be accurate However changes are made periodically These changes are incorporated in newer publication editions Gateway may improve and or change products described in this publication at any time Due to continuing system improvements Gateway is not responsible for inaccurate information which may appear in this manual For the latest product updates consult the Gateway Web site at www gateway com In no event will Gateway be liable for direct indirect special exemplary incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages In the interest of continued product development Gateway reserves the right to make improvements in this manual and the products it describes at any time without notices or obligation Trademark Acknowledgments Gateway and the Black and White Spot Design are trademarks or registered trademarks of Gateway Inc in the U S and other countries SpotShop Spotshop com and Your Ware are trademarks of Gateway Inc Intel Intel Inside logo and Pentium are registered trademarks and MMX is a trademark of Intel Corporation Microsoft MS MS DOS and Windows are trademarks or registered trademarks of Microsoft Corporation All other
10. gateway com Starting the monitor To start the monitor 1 Press the power button on the front of monitor The power LED turns on Power button 2 Turn on your computer 3 After your computer is running the power LED on the monitor should be green Allow about 10 seconds for the display image to appear If the power LED is not green or you do not see a display image check the connections For more troubleshooting information see Troubleshooting on page 15 4 Adjust the tilt of the monitor for the best viewing angle 5 After you see the Windows desktop press the AUTO SELECT button to automatically adjust your display image to the ideal settings 6 Use the on screen display OSD to adjust other monitor settings For more information see Adjusting monitor settings on page 7 Important When adjusting the monitor settings always press the AUTO SELECT button before entering the OSD This will M automatically adjust the display image to the ideal settings for the current screen resolution The best screen resolution is 1280 x 1024 O Adjusting monitor settings Use the external controls located on the monitor itself and software controls accessible in Windows to adjust the display image For more information about software controls see Software controls on page 10 External controls This monitor features an on screen display OSD that lets you adjust and save contrast brightness and
11. ge PHASE Minimizes any horizontal distortion and clear or sharpen the displayed characters OSD Menu SETUP LANGUAGE ENGLISH OSD POSITION gt Lama SIGNAL DSUB ANALOG FACTORY RESET NO 1024x 768 75Hz a PRESET MODE 59 DSUB ANALOG Software controls Color depth and screen resolution are two of the most basic monitor settings you may need to change Adjusting the color depth Color depth is the number of colors your video card uses Most images look best displayed with the maximum number of colors available Description LANGUAGE Changes the language of the OSD menu OSD POSITION Adjusts the OSD window position on the screen SIGNAL Switches between analog Dsub or digital DVI source signals RESET Returns settings to the factory defaults Windows lets you choose from several color depth settings for the monitor We recommend that you use the 32 bit True Color setting or the highest setting available at all times If the color in your images seems false or jumpy especially after you have played a game or run a video intensive program check the color depth setting and return it to 32 bit True Color if necessary To change the color depth 1 In Windows XP click Start then click Control Panel The Control Panel window opens If your Control Panel is in Category View click Appearance and Themes 10 OR In Windows 2000 click Start Settings then click Control Pa
12. he following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by Gateway could A void the FCC compliance and negate your authority to operate the product California Proposition 65 Warning Warning This product contains chemicals including lead known to the State O of California to cause cancer birth defects or reproductive harm 22 Canada Industry Canada IC Unintentional emitter per ICES 003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de Classe B prescrites dans le reglement sur le brouillage radio lectrique dict par Industrie Canada EPA ENERGY STAR As an ENERGY STAR Partner Gateway has determined that this product meets the ENERGY STAR guidelines for energy efficiency when used with a computer equipped with a Display Power Management System ENERGY STAR 23 Notices Copyright 2004 Gateway Inc All Rights Reserved 14303 Gateway Place Poway CA 92064 USA All Rights Reserved This publication is protected by copyright and all rights ar
13. keep the monitor in optimal working order Do not block the ventilation holes Do not expose the monitor to rain or use near water Keep the monitor away from radiators or heat vents Keep the monitor out of direct sunlight To clean the monitor use a soft cloth slightly moistened with water only Wipe the cabinet screen and controls Caution Do not use any type of abrasive pad or glass cleaner You will N permanently scratch the screen Troubleshooting If you have problems with the monitor the information in this troubleshooting section may help you solve them Important Make sure that the monitor has warmed up for approximately m 30 minutes before making any judgments about the picture quality No power Make sure that the power cord is connected correctly to both the back of the monitor and the wall outlet For more information about connecting the power cord see Connecting the monitor on page 2 15 No picture Make sure that the power cord is connected correctly to both the back of the monitor and the wall outlet For more information about connecting the power cord see Connecting the monitor on page 2 Make sure that the video cable is connected securely to the back of the monitor and computer For more information about connecting the video cable see Connecting the monitor on page 2 Make sure that the monitor power button is turned on If you have two computers connected to the monitor press
14. nel The Control Panel window opens 2 Click Double click the Display icon The Display Properties dialog box opens 3 Click the Settings tab Display Properties Display Gateway FPD 1940 on Intel r 82810E Graphics Controller Screen resolution Color quality Mare High 24 bit a 800 by 600 pixels y E II u Troubleshoot 4 Click the arrow button to open the Color quality or Colors list then click the color depth you want 5 To save your changes in Windows XP click OK then click Yes OR To save your changes in Windows 2000 click OK then click OK again O Help and For more information about adjusting monitor settings in Windows XP Support click Start then click Help and Support Type the keyword changing display settings in the Search box Search ____ JEJ then click the arrow Adjusting the screen resolution You can change the screen resolution to a size you prefer For example you can increase the resolution to fit more icons on your desktop or you can decrease the resolution to make reading and identitying objects on the monitor easier The higher the resolution the smaller individual components of the screen such as icons and menu bars appear www gateway com 11 Y J To change the screen resolution 1 In Windows XP click Start then click Control Panel The Control Panel window opens If your Control Panel is in Category View click Appearance and Themes OR In Window
15. o adjust the control to the desired level Press the AUTO SELECT button to return to the main navigation bar on the left of the OSD menu When you have finished making all adjustments press the MENU button to exit the OSD O OSD menus OSD Menu BRIGHTNESS CONTRAST 075 COLOR PRESET 9300K 6500K RED PU GREEN 4mm BLUE HIT GAMMA 4 POSITION 2 so gt 50 TRACKING CLOCK dun PHASE dun Description BRIGHTNESS Adjusts the amount of light in the darkest portion of the picture Use the lowest brightness setting you are comfortable with to maximize the life of the monitor backlights You may need to readjust brightness after the monitor has warmed up CONTRAST Adjusts the level of white between the lightest and darkest portions of an image PRESET Adjust the color temperature 9300K is bluish white 6500K is reddish white default RED GREEN BLUE Customizes the color levels Press the V button to move to the next color GAMMA Customizes the gamma level High gamma levels increase white levels and low gamma levels increase contrast VERTICAL POSITION Moves the display image up and down HORIZONTAL POSITION Moves the display image left and right You can also use the AUTO SELECT button to configure the vertical and horizontal position automatically CLOCK Minimizes any vertical bars or stripes visible on the screen background The horizontal screen size will also chan
16. ould only be operated from the type of power source indicated on the rating label If your product has a voltage selector switch make sure that the switch is in the proper position for your area The voltage selector switch is set at the factory to the correct voltage Openings in the monitor case are provided for ventilation Do not block or cover these openings Make sure you provide adequate space at least 6 inches 15 cm around the system for ventilation when you set up your work area Never insert objects of any kind into the monitor ventilation openings Some products are equipped with a three wire power cord to make sure that the product is properly grounded when in use The plug on this cord will only fit into a grounding type outlet This is a safety feature If you are unable to insert the plug into an outlet contact an electrician to install the appropriate outlet If you use an extension cord with this system make sure that the total ampere rating on the products plugged into the extension cord does not exceed the extension cord ampere rating If your system is fitted with a TV Tuner cable or satellite receiver card make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and buildup of static charges Care during use Do not walk on the power cord or allow anything to rest on it Do not spill anything on the system The best way to avoid spills is to avoid eating and
17. product names mentioned herein are used for identification purposes only and may be the trademarks or registered trademarks of their respective companies 24 ON LG FPD1940 GDE R1 27103 04016 NI
18. s 2000 click Start Settings then click Control Panel The Control Panel window opens 2 Click Double click the Display icon The Display Properties dialog box opens 3 Click the Settings tab Display Properties Themes Desktop Screen Saver Appearance Settings Display Gateway FPD 1940 on Intel r 82810E Graphics Controller Screen resolution Color quality More High 24 bit a 800 by 600 pixels nti HA Troubleshoot 4 Drag the Screen resolution or Screen area slider to the size you prefer 5 To save your changes in Windows XP click OK then click Yes OR To save your changes in Windows 2000 click OK then click OK again O Help and For more information about adjusting screen resolution in Support Windows XP click Start then click Help and Support Type the keyword changing screen resolution in the Search box Search ____ JEJ then click the arrow 12 www gateway com Video modes The monitor supports several video modes m Best video mode is 1280 x 1024 60 Hz The supported video modes are Screen Resolution Horizontal Vertical display mode Frequency Frequency 1 VGA 640 x 350 31 47 kHz 70 Hz 2 VGA 720 x 400 31 47 kHz 70 Hz 3 VGA 640 x 480 31 47 kHz 60 Hz 4 VESA 640 x 480 37 50 kHz 75 Hz 5 VESA 800 x 600 37 88 kHz 60 Hz 6 VESA 800 x 600 46 88 kHz 75 Hz 7 MAC 832 x 624 49 73 kHz 75 Hz 8 VESA 1024 x 768 48 36 kHz 60 Hz 9 VESA 1024 x 768 60 12 kHz 75 Hz 10 MAC 1152 x 870 68 68 kHz 75
19. ve any extension cables or switchboxes Make sure that the video cable is connected securely to the back of the monitor and your computer For more information about connecting the power cord see Connecting the monitor on page 2 Make sure that the video cable is not damaged Check the end of the video cable for any pins that might be bent or pushed in Color is not uniform Make sure that the monitor warms up for at least 30 minutes before making a final judgment about color uniformity or brightness Press the AUTO SELECT button to automatically adjust the display image to the ideal settings Image is not sized or centered correctly Press the AUTO SELECT button to automatically adjust the display image to the ideal settings Use the position controls to adjust the image For instructions on how to adjust the display image position see Adjusting monitor settings on page 7 The monitor has pixels that are always dark or too bright This condition is normal and inherent in the TFT technology used in active matrix LCD screens Gateway s inspection standards keep these to a minimum If you feel these pixels are unacceptably numerous or dense on your display contact Gateway Technical Support to identify whether a repair or replacement is justified based on the number of pixels affected 17 Specifications 18 Specifications are subject to change without notice or obligation Monitor 19 inch active matrix TFT
Download Pdf Manuals
Related Search