Garmin 190-01117-02 GPS Receiver User Manual
Contents
1. for the GMI 10 is from 5 F to 158 F from 15 C to 70 C Extended exposure to temperatures outside this range in storage or operating conditions may cause failure of the LCD screen or other components This type of failure and related consequences are not covered by the manufacturer s limited warranty Step 2 Flush Mounting the GMI 10 In addition to four of the included mounting screws number 8 ANSI 4 2 x 1 4 DIN7981 flush mounting the GMI 10 requires the following tools e Phillips screwdriver e Drill and in 3 2 mm drill bit for mounting holes 3 in 90 mm hole saw for pilot hole e Scissors e Center punch and hammer e File and sandpaper e Anti seize lubricant optional e Counterbore bit for fiberglass installations NOTE Ensure that the surface on which you mount the GMI 10 has sufficient open space behind it to accommodate the GMI 10 and the connected wires To flush mount the GMI 10 1 The flush mount template is included in the product box Trim the template and ensure that it will fit in the location at which you want to flush mount the smo GMI 10 2 The flush mount template has adhesive on the back Remove the protective liner and apply the template to the location where you want to flush mount the GMI 10 3 Using the 3 3 in 90 mm hole saw cut the mounting surface along the inside of the dashed line indicated on the flush mount template Use a file and sandpaper to refine the siz2. A GARMIN GMI 10 Installation Instructions To obtain the best possible performance install your GMI 10 Marine Instrument according to the following instructions If you experience difficulty during the installation contact Garmin Product Support or seek the advice of a professional installer The GMI 10 will communicate with NMEA 2000 or NMEA 0183 compatible sensors and devices and can show information such as speed heading water depth and fuel information when connected to the appropriate sensors Product Registration Help us better support you by completing our online registration today Go to http my garmin com Keep the original sales receipt or a photocopy in a safe place For future reference write down the serial number assigned to your GMI 10 in the space provided below The serial number is located on a sticker on the back of the GMI 10 Serial number Contact Garmin Contact Garmin Product Support if you have any questions while installing or using your GMI 10 In the USA go to www garmin com support or contact Garmin USA by phone at 913 397 8200 or 800 800 1020 In the UK contact Garmin Europe Ltd by phone at 0808 2380000 In Europe go to www garmin com support and click Contact Support for in country support information or contact Garmin Europe Ltd by phone at 44 0 870 8501241 Packing List and Accessories Before installing your GMI 10 confirm that your package includes the following items
3. If any parts are missing contact your Garmin dealer immediately Standard Package Optional Accessories e GMI 10 unit e Additional NMEA 2000 network components e Protective cover Tools Needed e Flush mount hardware e Jigsaw or 3 in 90 mm hole saw e NMEA 0183 data wiring harness e Drill and drill bits e 2 NMEA 2000 T connectors e Center punch and hammer e 2 NMEA 2000 terminators 1 male female e Scissors e 1 NMEA 2000 drop cable 2 m e File and sandpaper e 1 NMEA 2000 power cable 2 m 3 A fuse e Phillips screwdriver e Installation instructions e Anti seize lubricant optional To install and use your GMI 10 1 Select a location page 2 2 Flush mount the GMI 10 page 2 3 Connect the GMI 10 to the sensors and to power page 3 January 2010 190 01168 02 Rev A Printed in Taiwan Step 1 Select a Location for the GMI 10 Consider the following when you select an installation location e Provides optimal viewing as you operate your vessel e Allows easy access to the keypad on the GMI 10 e Is strong enough to support the weight of the GMI 10 and protect it from excessive vibration or shock e Allows room for the routing and connection of the cables There should be at least a 3 inch 8 cm clearance behind the case e Is at least 9 1 in 241 mm from a magnetic compass to avoid interference e Mount the GMI 10 in an area that is not exposed to extreme temperature conditions NOTE The temperature range
4. Taiwan www garmin com January 2010 Part Number 190 01168 02 Rev A Printed in Taiwan
5. e of the hole 4 Place the GMI 10 into the cutout to confirm that the four mounting holes are correct after refining the hole If not mark the correct locations of the four GARMIN mounting holes Remove the GMI 10 from the cutout 5 Using the center punch indent the center of each of the four mounting hole locations 6 Using a in 3 2 mm drill bit drill the four mounting holes NOTE If you are mounting the chartplotter in fiberglass it is recommended to use a countersink bit to drill a clearance counterbore through only the top gel coat layer This will help to avoid any cracking in the gel coat layer when the screws are tightened 2 GMI 10 Installation Instructions Place the GMI 10 into the cutout Securely tighten the four mounting screws through the GMI 10 into the drilled mounting holes NOTE Stainless steel screws may bind when screwed into fiberglass and overtightened Garmin recommends applying an anti galling stainless anti seize lubricant to the screw before using 9 Install the mounting covers by snapping them into place co N Step 3 Connect the GMI 10 to Sensors and to Power The GMI 10 can connect to sensors using either NMEA 2000 or NMEA 0183 Connecting the GMI 10 through NMEA 2000 The GMI 10 is packaged with the necessary NMEA 2000 connectors and cable to either connect the GMI 10 to your existing NMEA 2000 network or to build a basic NMEA 2000 network For more information on NMEA 2000 vi
6. ence Information The GMI 10 can receive the following approved NMEA 0183 sentences from a NMEA 0183 compliant device BOD BWC DBT DPT GGA GLL GSA GSV HDG HDM MDA MTW MWD MWV RMB RMC VHW WPL and XTE Specifications Physical Dimensions W x Hx D 456 x 4 x 1 5 in 109 x 111 x 48 mm Weight 9 6 oz 272 g Cables NMEA 0183 data cable 6 ft 1 8 m NMEA 2000 drop cable and power cable 6 ft 2 m Temp range From 5 F to 158 F from 15 C to 70 C Compass Safe Distance 9 in 241 mm Case Material Fully gasketed high impact plastic alloy waterproof to IEC 529 IPX7 standards Power GMI 10 power usage 2 5 W max NMEA 2000 Power Input 9 16 Vdc NMEA 2000 Load Equivalency Number LEN 6 300 mA Declaration of Conformity relevant provisions of Directive 1999 5 EC To view the full Declaration of Conformity go to Hereby Garmin declares that this product is in compliance with the essential requirements and other C www garmin com declaration of conformity Software License Agreement BY USING THE GMI 10 YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT PLEASE READ THIS AGREEMENT CAREFULLY Garmin Ltd and its subsidiaries Garmin grant you a limited license to use the software embedded in this device the Software in binary executable form in the normal operation of the product Title ownership rights and intellectual property righ
7. n line switch y Fuse J A L NMEA 2000 device a _ e not included 12 Vdc battery y ar pane it Additional Drop cable drop cable and Power cable T connector T connectors vf not included Female Male terminator eee terminator Creating a Basic NMEA 2000 Network Notes e To add additional sensors to your NMEA 2000 network follow the instructions included with the sensor e To learn more about NMEA 2000 and building a NMEA 2000 network visit www garmin com e The GMI 10 is powered by the NMEA 2000 network GMI 10 Installation Instructions Connecting the GMI 10 through NMEA 0183 The GMI 10 can receive NMEA 0183 data from one device The GMI 10 displays the received data but cannot transmit the data to another NMEA 0183 device or transmit the data to a NMEA 2000 network Use the diagrams to wire a NMEA 0183 device to your GMI 10 Use 22 AWG shielded twisted pair wiring for extended runs of wire Solder all connections and seal them with heat shrink tubing Color Function Black Accessory Off KC ON GARMIN Yellow _ Accessory On gt Blue Tx A gt White Tx B lt Brown Rx A Ne lt Green Rx B GMI 10 Data Cable C cm0 WIRE WIRE gore GPS 17 17x NMEA 0183 HVS Antenna WHITE wane ites y 5445 ORANGE GARMIN COLOR F
8. o a 12 Vdc power source through a switch Connect to the ignition switch of the boat if possible or through an appropriate additional switch not included Connect the NMEA 2000 power cable to one of the T connectors 4 Connect the included NMEA 2000 drop cable to the other T connector and to the GMI 10 Add additional T connectors for each sensor not included you want to add to the NMEA 2000 network and connect each sensor to a T connector with the appropriate drop cable not included 6 Connect the appropriate terminators to each end of the combined T connectors NOTICE You must connect the included NMEA 2000 power cable to the ignition switch of the boat or through an external switch The GMI 10 will drain your battery if it is connected directly amp Sz 7S GMI 10 Installation Instructions NMEA 2000 device a ee not included not included Drop cable Lt included T connector included mny l MIN O 4 Existing NMEA 2000 network gt Connecting the GMI 10 to an Existing NMEA 2000 Network J Di GMII0 Ignition or i
9. or with only one receiving Rx line the NMEA 2000 bus and the NMEA 0183 device must be connected to a common ground NMEA 2000 PGN Information Use this table to determine the approved NMEA 2000 PGN information that can be received and transmitted by a GMI 10 when communicating with a NMEA 2000 compliant device 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA Command Request Acknowledge Group Function 126208 NMEA Command Request 126464 Transmit Receive PGN List Group Function Acknowledge Group Function 126992 System Time 126464 Transmit Receive PGN List 126996 Product Information Group Function 127250 Vessel Heading 126996 Product Information 127489 Engine Parameters Dynamic 127505 Fluid Level 128259 Speed Water Referenced 128267 Water Depth The GMI 10 is 129025 Position Rapid Update NMEA 2000 certified 129026 COG amp SOG Rapid Update 129029 GNSS Position Data 129044 Datum 129283 Cross Track Error 129284 Navigation Data 129285 Navigation Route WP information 129539 GNSS DOPs 129540 GNSS Sats in View 130306 Wind Data 130310 Environmental Parameters 6 GMI 10 Installation Instructions 130311 Environmental Parameters 130312 Temperature 130313 Humidity 130314 Actual Pressure NMEA 0183 Sent
10. sit www garmin com Follow the directions and reference the diagrams on page 4 to either connect the GMI 10 to your existing NMEA 2000 network or to build a basic NMEA 2000 network To connect the GMI 10 to your existing NMEA 2000 network 1 Determine where you would like to connect the GMI 10 to your existing NMEA 2000 backbone NMEA 0183 NMEA 2000 2 Disconnect one side of a NMEA 2000 T connector from the backbone at Data an appropriate location If you need to extend the NMEA 2000 backbone connect an appropriate NMEA 2000 backbone extension cable not included to the side of the T connector you disconnected 3 Add the included T connector for the GMI 10 in the NMEA 2000 backbone by connecting it to the side of the T connector you disconnected 4 Route the included drop cable to the bottom of the T connector you just added to your NMEA 2000 network If the included drop cable is not long enough you can use a drop cable up to 20 ft 6 m long not included 5 Connect the drop cable to the T connector and the GMI 10 NOTICE If you have an existing NMEA 2000 network on your boat it should already be connected to power Do not connect the included NMEA 2000 power cable to an existing NMEA 2000 network because only one power source should be connected to a NMEA 2000 network To create a basic NMEA 2000 Network 1 Connect the two T connectors together by their sides 2 The included NMEA 2000 power cable must be connected t
11. ts in and to the Software remain in Garmin and or its third party providers You acknowledge that the Software is the property of Garmin and or its third party providers and is protected under the United States of America copyright laws and international copyright treaties You further acknowledge that the structure organization and code of the Software for which source code is not provided are valuable trade secrets of Garmin and or its third party providers and that the Software in source code form remains a valuable trade secret of Garmin and or its third party providers You agree not to decompile disassemble modify reverse assemble reverse engineer or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software You agree not to export or re export the Software to any country in violation of the export control laws of the United States of America or the export control laws of any other applicable country GMI 10 Installation Instructions N For the latest free software updates excluding map data throughout the life of your Garmin products visit the Garmin Web site at www garmin com A GARMIN 2010 Garmin Ltd or its subsidiaries Garmin International Inc 1200 East 151 Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire S040 9LR UK Garmin Corporation No 68 Jangshu 2 Road Sijhih Taipei County
12. use RED RED G MI 10 BLACK Device YELLOW ORANGE BLUE 2 e r GMI 10 Gul 10 COLOR Device D O GARMIN WIRE FUNCTION POWER POWER GND NMEA 0183 Compliant Device Tx A Wiring the GMI 10 to a Standard NMEA 0183 Device Notes e Consult the instructions for your NMEA 0183 compliant device to identify the Tx A and Tx B wires e When connecting NMEA 0183 devices with two transmitting and two receiving lines it is not necessary for the NMEA 2000 bus and the NMEA 0183 device to connect to a common ground e The yellow accessory on wire and the black accessory ground wire are used only when wiring the GMI 10 to a Garmin GPS 17 17x antenna GMI 10 Installation Instructions 5 If your NMEA 0183 compatible device has only one transmitting wire Tx connect it to the brown wire Rx A from the GMI 10 and connect the green wire Rx B from the GMI 10 to NMEA ground NMEA 2000 network Battery WIRE WIRE COLOR 12Vde FUNCTION we D POWER GMI 10 GREEN NMEA GND BLACK POWER GND Compatible Device OOOO o BROWN Tx GARMIN J Wiring the GMI 10 to a NMEA 0183 Device with One Transmitting Wire NOTE When connecting a NMEA 0183 device with only one transmitting Tx line
Download Pdf Manuals
Related Search