Home

Fujitsu C150-E187-01EN Scanner User Manual

1. OK Enables the new setting and terminates the option dialog box Cancel Cancel Disables the new setting returns the setting to the previous value and terminates the processing Help Help Displays online help 21 The options are described below Option la po desree e r ota Ez SRE Figure Option dialog Rotation Flip Side Rotation Specifies the binding of the document when both sides are scanned using ADF Book Outputs the scanned image for both sides as is Select this option to scan documents bound on the left or right side Fanfold Scans only the back side and outputs the scanned image rotated 180 degrees Select this option to scan documents bound on the top or bottom 22 Rotation Degree Rotation Degree T degree Outputs the scanned image rotated to the right or left 90 degrees 0 0 degree Outputs the scanned image as 1s 90 0 degree Outputs the scanned image rotated 90 degrees to the right clockwise 90 0 degree Outputs the scanned image rotated 90 degrees to the left counterclockwise 180 0 degree Outputs the scanned image rotated 180 degrees top and bottom reversed Auto Deskew Auto Deskew When ADF is used for scanning this option detects skew of the document being fed and automatically corrects skewing Check the checkbox to enable this option This option may not be supported for some scanners See Relevant Imag
2. AET u f Normal Light Dark C Light This option specifies the relationship between the threshold value and the maximum density This specification method depends on the Scan mode setting In for OCR mode use the slider to set the inclination and density level To specify the value drag the tab of the slider to the desired setting position The current setting value is displayed on the right figure on the left In for Image mode select Normal or Lightest figure on the right If IPC 3 3D and IPC 4D have been installed there is no difference between for OCR and for Image The slider is used to set the inclination and density level The figure on the right is not displayed Gamma Curve Gamma Curve ocR 1 This option specifies the gamma correction curve pattern The available choices depend on the Scan mode setting In for OCR mode select OCR1 or OCR2 In for Image mode select Dark Image or Even For IPC 3 3D and IPC 4D the gamma curve need not be specified because the contrast 1s adjusted automatically Gamma Curve 1s not displayed Equal to White Equal to White At conversion to binary this option specifies whether to set the data to black or white when the threshold value and the value of the scanned data are equal When using IPC 4D this option cannot be selected Ball Point Pen Mode Ball paint pen made When an image made with a pencil or ball point pen
3. ate oy UNUM MM et PEREN KEK N E ku XM P er DI MM Dp Dr Mp D D Dus Dui Eod 100 a UR OW RS a a baa se as a urn 7 M x pia 7 PS x n P ae ee at n P x I Tar X e Mutat e E Cw n RUMOR a ar MR ro es a Pa E Se ER K SEWE b 200 P cuts a A A A t Mom mL x M ML UM a qe qe e rue D xbox 300 m QUAKE The preview window is used to display the temporary image of read data and for setting the scanning Area For settings see Scanning Area later in this manual Also see the description of the Preview button later 1n this manual Ruler The large divisions are labeled as Unit The scale also varies with the selected scanner Message line The message line 1s the bottom line of the dialog in which a brief explanation of an input item or a setting item is displayed when the mouse cursor is moved over the item 10 Data size The approximate amount of data per image when data is scanned in the present option Note This value is the amount of uncompressed data The size of the stored file will differ from this value and is usually smaller if image compression is chosen and the image is compressed 4 4 Setting Information on Image Scanning Current side Duplex Individual Setting Frant Back e Individual Setting When a scanner that allows duplex scanning is used specifies the page which sets the image
4. V User response Enter a file name that does not contain the above characters Then make the settings again The image scanner cannot be found Cause Possible causes include the following an image scanner that is not supported by this driver has been connected no image scanner has been connected or the cable is not connected Otherwise the initial values of the image scanner were overwritten while the driver was open User response Check the connection of the image scanner Also be sure to close the driver before using the initial value adjustment utility in the image scanner The specified image scanner is being used Cause The image scanner may be already in use by another application or the TWAIN driver may have been started twice User response User response After all applications are terminated restart the image scanner for scanning 64 An input output error occurred in the image scanner Cause A fault occured during the scan operation of the image scanner There may be a fault in the image scanner itself User response Turn off the power of all devices then turn on the power of the computer before turning on the scanner and retry scanning If the error still occurs contact the retail store where the image scanner was purchased or the nearest service center Paper jammed in the ADF Cause A paper jam occurred in the device User response Turn off the power of the device then remove the pa
5. aaa a EN saa A ERKEK a KESEK ALET a ra ra ra d diee boe di e odi dede d dede ded Po MENU ME deed diee diee Black Av Hike Threshold Pat at at a e t er e er a e e e ee e e a Ng e e e e kr e ke e kd ae ai ET static Threshold lt fa Halftone CHE t Dither Pattern Contrast b J u u u u u u u u nm u um m m m m 128 TWAIN drive ush FT Key to show help u u u u u u u u u u u u zm m u i i i i i i i Oe eee i i i i i i i i i i i i i i i i i lI i i i i i li MI ata Size about 3 MB image seen relied di Figure Main Dialog The following pages contain the explanation and operation description for each part 4 3 Displaying Driver Information Image scanner name Image Scanner M4097Ddim IPC4D 32MB Select The model name option port name and capacity of internal scanner memory in units of megabytes of the connected image scanner are displayed If no image scanner is connected this field is blank To change the selected scanner click the Select button to display a list of connected scanners and select a scanner from the list The type of IPC option board is displayed if an image processing option board is installed in the scanner IPC 3 3D may not be detected normally as it is affected by the version number of the machine type and device In this case IPC2 is displayed Preview window 100 200 ka eie E
6. displayed 2 Double click on Add Remove Programs from the icon list of the Control Panel The panel of properties of Add Remove Programs is displayed Select Scanner Utility for Microsoft Windows from the Install Uninstall list 4 Click on the Add Remove button When the confirmation dialog is displayed click on OK if you are ready to uninstall 5 When uninstallation is completed click on OK Note Image files that have been scanned and saved will not be deleted If other TWAIN compliant applications and drivers have been installed and you are asked whether or not to delete files shared with them such as the TWAIN Manager select NO to avoid deleting them 4 Using the Driver 4 1 Selecting the Driver To use this driver from the TWAIN application select FUJITSU TWAIN32 from the TWAIN data source driver selection screen For general application the data source selection screen is displayed by selecting the Select Scanner or Acquire menu Refer to the instruction manual for the application used for details 4 2 Screen Configuration M TWAIN Driver 32 ES Paper Size A3 210823 7min 100 Scanning Area Lett Top Width Length 200 z j j 21 t 287 mm Frant Ho Iv Individual Setting 300 AAA AA Image Mode Brightness Lee erk kk ek e eh M ST aee et Puen a dq dodo d 0 E ME d qd did d dde Automatic Seoaration 128 Vae ee p
7. scanning information To scan using the same settings as those for Front side and Back side clear the checks in the Individual Setting checkbox on the Front and Back tabs A single Duplex tab will be displayed at the left so that the same image scanning information can be set for Front side and Back side To scan using different settings for Front side and Back side check the Individual Setting checkbox on the Front and Back tabs Two tabs Front and Back will be displayed at the left Select each tab and enter the desired settings This is only effective when ADF Duplex is selected for the method of paper feed For scanner types which permit duplex scanning see Relevant Image Scanner Specification in the Appendix Resolution r Resolution 260 x 800 Specifies the number of pixels dots per inch Select a fixed resolution from the list or Custom High resolution requires more memory The supported resolution depends on the type of scanner and the options installed See Relevant Image Scanner Specification in the Appendix 11 Paper Size Paper Size Er 21020 mim Selects a paper size corresponding to the size of the document to be scanned Select a standard paper size from the list or Custom If Custom is selected the Custom Paper Size Setting dialog appears Enter the size of the document to be scanned Some paper sizes may not be accepted by your dev
8. Error diffusion 2 0 sec or less A4 200 dpi 2 pages minute 200 dpi A4 55 kg Maximum 50 sheets ream weight 55 kg A4 High quality paper Normal temperature and humidity Maximum 297 mm x 432 mm A3 or Double letter sized paper A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Letter Letter Landscape Legal Double letter US Executive US Executive Landscape Specified one location Enabled 256 steps 3 internal types can be downloaded Auto binary simplified method Image processing option installed Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Use of FUJITSU Scanner Control Center Disabled Use of this scanner may require installation of the optional image compression option board CMP 2 in the scanner device This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 74 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed ADF stacker capaci
9. Gray scale 8 bits output Halftone Patterns ADF scanning speed ADF stacker capacity Document size Supported regular paper f Cutout specification Background compensation Contrast setting Gamma pattern Image processing function M4099D device name fi 4990 Desktop Reduced optical system Automatic Document Feed ADF simultaneous double sided reading Long page scanning 297mmx878mm Fluorescent tube White Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi With image processing option 50 dpi to 400 dpi at steps of 1 dpi 10 bit 1024 levels Enabled 200 dpi only Dither matrix can be downloaded Error diffusion lt Asynchronous Scanning gt 90 pages per minute 200 dpi A4 55 kg Double sided 90 pages per minute 200 dpi A4 55 kg 180 screens per minute Single sided lt Synchronous Scanning gt 80 pages per minute 200 dpi A4 55 kg Double sided 60 pages per minute 200 dpi A4 55 kg 120 screens per minute Single sided Maximum 1 000 sheets ream weight 55 kg A4 High quality paper Normal temperature and humidity Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Double Letter Letter Letter Landscape Legal US Executive US Executive Landscape Specified one location Enabled 256 levels 3 internal types can be do
10. Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal Endorser stamp With endorser option Reverse side minimum left margin printing position of 20 mm Maximum number of characters to be printed 20 characters Interface SCSI II Job control Enabled Use of FUJITSU Scanner Control Center Disabled 2 IfOmm is specified as the endorser print position printing will begin 20 mm from the edge of the page 78 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns ADF scanning speed Double sided ADF stacker capacity Document size Supported regular paper Cutout specification White level follower Contrast setting Gamma pattern Image processing function M3099GH Desktop Reduced optical system Automatic Document Feed ADF simultaneous double sided reading Fluorescent tube Green Horizontal scanning 200 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi with image processing option 50 dpi to 400 dpi at steps of 1 dpi 8 bit 256 levels Disabled Dither matrix can be downloaded Error diffusion Single sided 80 pages per minute 200 dpi A4 55 kg 60 pages per minute 200 dpi A4 55 kg 120 screens per minute Maximum 1 000 sheets ream weight 55
11. Specification M3093GX device name fi 4320S Desktop Reduced optical system Document fixed scanner unit moving flat bed Automatic Document Feeder ADF Xe discharge tube Green Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi With image processing option 50 dpi to 800 dpi at steps of 1 dpi 8 bit 256 levels Enabled 8 bits Dither matrix can be downloaded Error diffusion 1 6 sec or less A4 200 dpi 27 pages minute 200 dpi A4 55 kg Maximum 50 sheets ream weight 55kg A4 Maximum 216 mm x 356 mm Legal size paper A4 A5 A5 Landscape A6 A6 Landscape B5 B6 B6 Landscape Letter Legal US Executive Specified one location Enabled 256 steps 3 internal types can be downloaded Image processing circuit II required Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Use of FUJITSU Scanner Control Center Disabled 1 Use of this scanner requires that the image compression option board CMP 2 be installed in the scanner 2 This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration 3 Not all sizes of paper can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 72 Produ
12. feeder ADF for feeding scanned document The ADF usually enables the documents to be scanned only once The flat bed allows scanning the same documents repeatedly Flatbed Reads a document placed on the flat bed of the device ADF Simplex Reads the document on the device s automatic document feeder ADF Here only one side is read ADF Duplex To scan both the front and the back of a page select this option If this option is selected the document is scanned in the front to back to front to back order This option can be used only for scanner models that support duplex scanning The Duplex Function requires that the calling application supports continuous scan If the application does not support continuous scan only the data for the front side of the page is passed to the application Some scanner models do not support this option See Relevant Image Scanner Specification in the Appendix Long page front To scan the entire side of a long page whose length exceeds the vertical size of an A3 sheet select this option The front side and back side can be specified using the same method used for ADF If this option is selected the Paper Size Setting dialog box opens Specify the size of the document to be scanned In this mode however the preview window cannot be displayed and the scanning area cannot be specified Scanner models that do not support this option do not display the Scan Type s
13. front side or back side was set as the object to be set User response Specify Gray Scale only when making the settings for both sides Dither pattern file not found Cause File download has been specified but a file has not been selected User response Use the File button to specify a file Gamma pattern file not found Cause File download has been specified but a file has not been selected User response Use the File button to specify a file Selected file could not delete Cause If the selected setting file is write protected it cannot be deleted User response Use Explorer to delete the file later 63 Description not specified Cause The description of the setting file has not been specified User response Enter the description of the setting file in the description field Then try scanning again Filename not specified Cause The filename of the setting file has not been specified User response Enter the filename of the setting file Then try scanning again Specified string is too long Cause The specified string is too long Up to 128 en size characters and up to 64 em size characters can be specified User response User response Reduce the number of characters in the string so that they do not exceed 128 en size characters Then try scanning again Cannot specify next words for filename V Cause The specified filename contains one or more of the following characters
14. graph area Save The gamma pattern currently being edited is saved in the file whose name is displayed above the graph area If no filename is displayed the pattern is named and saved in that file Save As The gamma pattern currently being edited is named and saved in that file The saved filename is then displayed above the graph area Close Select this to exit the editing program 53 5 9 Help menu FA Gamma Pattern E ditor File About 200 About Information related to this editor and its version number is displayed 54 5 4 Gamma Pattern Editing 4 Graph Area The graph area is a 256 dot x 256 dot white square area bordered by black lines where the relationship between the input values of 0 to 255 x axis and output values of 0 to 255 y axis 1s indicated in blue lines Each graph dot represents one division unit Gradation The input is displayed in black and white in 256 single dot steps from 0 at the left border to 255 at the right border The gama function of the scanner is displayed After saving it the displayed gray scale gama function is fixed and constant The output values are displayed in single dots in relation to the input values and the brightness of the output equipment is displayed To ensure accurate display the display must be set for True Color or greater Gamma Calculation of the output values is based on the value y entered in the edit box the g
15. gt CONEA ED 73 75 Basic Mes LNT gt HAL dar Paper Aze EA Pe Scans Ansa Left gt QUU moh Tan NAT sm hd The information of the setting file selected in Setting Files is displayed Show this dialog next open checkbox Show this dialog next open If this checkbox is checked Basic Scan Dialog will be activated the next time the driver is activated OK button Makes the new setting valid closes this dialog box and returns to the main dialog Add button Add Adds the setting of the current driver to a setting file File addition Description Configuration t far Document J Filename contig i Cancel Pressing the Add button opens the File addition dialog Enter the Description and Filename as shown in the example above Then press the OK button to add the new setting file To cancel press the Cancel button Description Enter a character string to be displayed in the selection frame of the Setting Files 44 Filename Specify the name of the file used to save the settings Delete button Delete Deletes unnecessary setting files Select the setting file to be deleted and then press the Delete button A confirmation dialog will be displayed Press the OK button to delete the setting file To cancel press the Cancel button Help button Help Displays online help 45 4 10 Basic Scan Dialog The basic scan dialog contains only th
16. image based on the brightness of the image A value is specified using the slider The smaller the value the lower the variance becomes The higher the value the higher the variance becomes To specify the value drag the tab of the slider to the desired setting position The current setting is displayed on the right This option is mainly used for optical character recognition OCR It enables dark and bright images in a document to be scanned effectively 35 This option is valid only when Simple auto binary is set Advance Front Black amp White DTG mode Color Gray OTC Density ocan mode for OCR Tor Image Threshold Curve Mo e Hormel i 1 i i i i 3 C ett is uis Equal to White Gamma Cure ocR 1 Filtering Noise Removal Ball point pen mode None a OCR Smoothine Figure Advance dialog DTC Mode Scan mode ocan mode for OGR for Image This option selects one of the following two scan modes for OCR This mode is for text recognition applications where irregularity in the image is undesirable for Image This mode is for image scanning applications that scan images without prior smoothing The specification changes the specifiable items and members for Threshold Curve and Gamma Curve The selection screens for for OCR and for Image are not displayed if IPC 3 3D and IPC 4D are installed 36 Density curve Threshold Curve
17. in README TXT which is included in the installation media Please read these notes before use Adaptec EX SCSI Pro Version 4 5 or later or the following 32 bit versions of ASPI Manager included for example in the Adaptec SCSI installer for Windows 95 Windows NT or on Fujitsu SCSI driver disk V1 2 Windows 95 Windows 98 Windows NT 4 0 V4 01 or later Windows 2000 Professional Edition V4 60 or later RAM of 16 megabytes or more Free hard disk space of 4 megabyte or more CD ROM drive required for installation Mouse recommended 1 3 Explanatory Notes The descriptions in this manual are prepared based on the following rules Menus and buttons The menus and buttons used in the program description are enclosed in Example File menu OK button Keyboard The keytop indications comply with the standard keyboard of the Fujitsu FMV series Major differences between the Fujitsu FMV keyboard and other keyboards are shown below FMV keytops Other possible keytops Alt Previous screen GRPH Ctrl CTRL Esc ESC Enter Return Shift SHIFT Back space Backspace BS Fl PF1 f 1 Terms related to mouse operation Terms related to major mouse operations are explained below Click To press and release the mouse button Double click To quickly press the mouse button twice Drag Move the mouse while keeping the mouse button pressed Notes on operation procedures If some menus need to be operated in a cert
18. processing using the dithered download pattern specified in the dithered download file described later Some scanner models do not support this function See Image Scanner Specification in Appendix Error Diffusion Error Diffusion minimizes the difference between the pixel density of the scanned image and the pixel density of the printed image to create better reproduction of a scanned photograph Some scanner models do not support this function See Relevant Image Scanner Specification in Appendix Scanning Parameters For fine scan adjustments Since there is no fixed set of values set by trial and error Brightness Brightness Ea Sets the brightness of the overall image Specify the brightness with a number in the range of 1 bright to 255 dark To brighten the overall image decrease the value of the setting To darken the overall image increase the value This parameter can be set if Halftone or Automatic Separation is selected for Image Mode Threshold Threshold pm m Sets the threshold value by which the black and the white of black and white images are distinguished Specify a number in the range of 1 bright to 255 dark This parameter can be set only if Black amp White is specified for Image Mode In addition if Auto Binary is selected the scanner will automatically use the appropriate threshold value As a result the set value cannot be changed 1
19. reading Fluorescent tube Green Horizontal scanning 200 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi With image processing option 50 dpi to 400 dpi at steps of 1 dpi 8 bit 256 levels Disabled Dither matrix can be downloaded Error diffusion lt M3099G gt Single sided 55 pages per minute 200 dpi A4 55 kg Double sided 50 pages per minute 200 dpi A4 55 kg 100 screens per minute M3099GX Single sided 60 pages per minute 200 dpi A4 55 kg Double sided 50 pages per minute 200 dpi A4 55 kg 100 screens per minute lt M3099G gt Maximum 500 sheets ream weight 55 kg A4 M3099GX Maximum 1 000 sheets ream weight 55 kg A4 Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Double Letter Letter Letter Landscape Legal US Executive US Executive Landscape Specified one location Enabled 256 levels 3 internal types can be downloaded Use of FUJITSU Scanner Control Center Disabled This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used TI Image processing function Automatic binary simple system With image processing option Outline emphasis
20. specified incorrectly internally The calculation result exceeded the value that can be expressed internally User definition is not registered internally Cause This is a program error that occurs during command exchange between the driver and the image scanner User response Try again by rebooting the machine If the error persists contact the retail store where the product was purchased or the nearest service center A general fault of the MSG_XXXXX response internally Cause This is a program error that usually occurs during internal message transfer This message involves the sub messages described later User response Contact the retail store where the product was purchased or the nearest service center A general fault of the DAT XXXXX response internally Cause This is a program error that usually occurs during internal data transfer This message involves the sub messages described later 67 User response Contact the retail store where the product was purchased or the nearest maintenance service center A general fault of the DAT XXXXX MSG SET and unsupported type response Internally Cause This is a program error that usually occurs while making the internal data settings User response Contact the place of purchase or your nearest maintenance and service center An undefined error occurred Processing cannot be continued because of insufficient memory The data source cannot be found
21. specified plug in Cause The application to be used for the plug in may not have been installed User response Verify that the application to be used for the plug in has been installed If no application is found install it 70 Scanner could not find although it searched again Check the connection of the scanner and retry again Cause The scanner power may not have been turned on or the cable may have been connected incorrectly Otherwise the OS may not recognize the scanner User response Make sure that the scanner power has been turned on and the cable has been connected correctly then retry rescanning Or check if the OS recognizes the scanner If the OS does not recognize it let it recognize the scanner then retry Can not rescan the scanner Close the application using the driver and retry again Cause An attempt was made to rescan while the driver was in use User response It 1s impossible to rescan while the driver is in use Close the application that uses the driver and retry Can not get the EEPROM data The setting of the function key can not change Check the connection of the scanner Can not change the setting of the function key Check the connection of the scanner and try the operation again Cause While the scanner with function keys are being monitored the scanner power may be turned off or the cable may be connected incorrectly User response Make sure that the scanner power has been turned on and the
22. the input and the resulting distortion must be corrected One of the following can be selected as a correction pattern Normal Soft Sharp Download Pattern or Custom 32 ownload Gamma Pattern Selection File Mame OK DIAN T twain 323 Escala Tel EN Cancel i Add Delete When Download Pattern is selected the above dialog box opens Select the gamma pattern download file to be used from the list of file names Then press the OK button Correction will then be executed using the selected gamma pattern If the gamma pattern download file has not been registered in the list of file names use the Add button to register the file See Download Pattern File for information about how to specify the file Custom 22 2 When Custom is selected a custom specification can be entered Entering an arbitrary value between 0 1 and 10 0 enables a gamma pattern corresponding to the entered value to be specified White Level Follower White Level Follower Auto Select this option to scan a document whose background color is not white such as a newspaper Select Auto Enable or Disable When Enable is selected the document is scanned using background follow up for line drawings When Disable is selected the document is scanned using the standard basic white background for photographs When Auto is selected the option automatically switches to the optimal setting
23. there is sufficient free space on the hard disk to install the software 3 2 Starting Installation 1 Start Windows Note A user name with administrator authority must be used to log on to Windows R 2000 or Windows NT R 4 0 Ask the system administrator for the details of logging on 2 Close any other currently open applications Insert the setup CD ROM in the CD ROM drive Here the CD ROM drive is temporarily called D If the environment you are using is different replace the appropriate parts below Double click on install exe in the D Driver l ASPI folder of the CD ROM using Explorer Then installation starts When an automatic start is specified the start screen of the setup disk is displayed Installation can be started from this screen too When the setup screen is displayed continue the process by following the on screen instructions Confirm that the following group is created when setup has been completed The displayed icon depends on the selection of Components during installation wr Scanner Utility for Microsoft Windows File Edit View Favorites Took Help J e Downoad Fujitsu ReadMe TWAIN Driver pattern editor Scanner Help Control Center Figure Fujitsu TWAIN group 3 3 Uninstall The uninstall process removes the software and returns the hard disk to its pre installation state 1 Click on Start followed by Settings and then Control Panel The Control Panel is then
24. to be reduced Cause A value exceeding the data capacity of the scanner was specified As the resolution 1s increased the amount of data to be scanned also increases User response Decrease the resolution or reduce the size of the scan area 62 The value for custom paper is higher than the maximum scan size Width needs to equal 279 mm or less and length needs to equal 420 mm or less The value for custom paper is higher than the maximum scan size Width needs to equal 11 inch or less and length needs to equal 16 53 inch or less The value for custom paper is higher than the maximum scan size Width needs to equal xxx pixel or less and length needs to equal xxx pixel or less Cause A value exceeding the limit applicable to the scan area of the scanner was specified User response To specify a custom paper size specify the value that is smaller than the value applicable to the device The resolution must be less or equal to xxx dpi when scanning in Gray Scale Cause A value exceeding the limit of resolution for gray scale scan was specified User response Specify a resolution value that is below the indicated xxx dpi Cannot specify Gray Scale with Custom resolution Cause Custom resolution was designated when multi tone gray scale was designated User response Designate a resolution value other than Custom Cannot specify Individual Setting with Gray Scale Cause Gray scale was specified in the settings for the
25. 00 dpi A4 55kg 90 screens per minute Color Single sided 12 pages per minute 200 dpi A4 55 kg Double sided 11 5 pages per minute 200 dpi A4 55kg 223 screens per minute Maximum 100 sheets ream weight 55 kg A4 High quality paper normal temperature and humidity Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Letter Letter Landscape Double Letter Legal US Executive US Executive Landscape Specified one location Enabled 256 steps 3 internal types can be downloaded This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 83 Image processing function Interface Job control Double feed detection Long page scanning Automatic binary simple system Outline emphasis Outline extraction SEE Selectable Edge Enhancement De Screen Reverse image With image processing option Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Enabled Enabled front side and both sides Use of FUJITSU Scanner Control Center Enabled 84 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal
26. 3 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 9 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 51 5 Using the Gamma Pattern Editor 5 1 Start up Click on Start and select Download Pattern Editor from Scanner Utility for Microsoft Windows under Programs The following menu is displayed Eg Gamma Pattern Editor El ee Figure Gamma Pattern Editor Tool start up menu 22 5 2 File menu Pid Gamma Patte Herr Save Save As Close Load This menu is used to read the Gamma Download file and display the graph and gradations The name of the open file is displayed above the
27. 4 USMO TNE DAVE eem 8 M Se FEC UNL NL l D Vl Ue yn ena nena sitos t OE D C CE de 8 42 creen CONNGUrAUO riales 9 4 3 Displaying Driver IO Malaria 10 4 4 Setting Information on Image Scanning u EE 11 4 5 Specitying Driver OD6FatlOn ooo rettet ete tette Qa kab ka AA d ka tete ta 18 oie 20 d DODO INS LO uh 21 4 9 oetung Advance ODLIONIS oa a yx ii AAA AA AAA 31 4 9 Setting the Configuration Options oocccccocccccccnncconnnonocononannnonanncnonenononencnnns 43 4 10 Basic Scan DIaloGus edocuit e dude dadas tau e Dex duda duet Deux aedes nien 46 2511 Downoad Patern e xot ost OA O 48 5 Using the Gamma Pattern Editor 52 A A 52 di O J HETO M ota aa ata a W GG abe a6 na 53 S lan Helan DEP E o E CO E see Dei 54 54 Gamma Pattern GHG usines Betten idet Retina a 55 6 How to Use the FUJITSU Scanner Control Center 56 6 ie 0 c 56 6 2 How to Start the FUJITSU Scanner Control Center 56 CERON ODIM ONU M 57 Tz Uroublesnoollng nonsi pao EE Ec EXC ka au Na kS s 62 Fal EON NSS SAC CS E UU M EIE 62 7 1 1 Messages from the TWAIN Driver ccoocccocccocccoccocccconcconcconoconoconocononanonanonos 62 7 1 2 Error messages relating to gamma correction pattern editing 69 7 1 3 Messages concerning to FUJITSU Scanner Control
28. 6 In addition if Auto Binary 1s selected the scanner will automatically use the appropriate threshold value As a result the set value cannot be changed If the light color in the scanned document is read as white increase the threshold value To eliminate light colored areas in the scanned document decrease this value 17 Contrast Threshold u Sets the contrast of light and shadow in a scanned image Specify the contrast with a number in the range of 1 low soft to 255 high sharp The contrast can be set if Gray Scale is selected in Image Mode If this value is increased the dark part of the image is shown darker and the light part is shown lighter Some scanner models do not support this function See Relevant Image Scanner Specification in Appendix 4 5 Specifying Driver Operation Preview Preview Reads in a preliminary image based on set values and displays the image in the preview window Before actual scanning the preview function can be used to display the entire document for specifying the desired scan area This function is available only on devices that support the use of a flat bed Some models do not support this function See Relevant Image Scanner Specification Scan scan Scans the specified scan range based on set values The following progress indicator is displayed during scanning to show the progress of the scan operation To stop scanning c
29. C150 E187 O1EN Scanner Utility for Microsoft Windows lt 32bit gt Version 8 0 cO FUJITSU Introduction Thank you for purchasing the Scanner Utility for Microsoft Windows V8 0 This software contains a TW AIN compliant image scanner driver simply called driver in this guide and utilities This guide provides a description summary of the driver as well as a description of the installation method and procedures for appropriate use Please read this guide before starting to use the software In addition read the README TXT file on the CD ROM for the latest information not included in this manual In this guide product names are abbreviated as follows e Microsoft Windows 95 operating system Windows 95 e Microsoft Windows NT Workstation operating system Version 4 0 and Microsoft Windows NT Server operating system Version 4 0 Windows NT 4 0 e Microsoft Windows 98 operating system Windows 98 e Microsoft Windows 2000 operating system Windows 2000 e Microsoft Windows Millennium Edition Windows Me When Windows 95 Windows 98 Windows NT 4 0 Windows 2000 and Windows Me are referred to collectively they are simply referred to as Windows Unless otherwise indicated explanations refer to Windows 95 n Windows 98 Windows NT 4 0 Windows 2000 and Windows Me collectively Trademarks MS DOS Microsoft Windows and Windows NT are regis
30. Cause A value exceeding the range allowed for an input item was input User response Input a value inside the allowed range Refer to the input item or the image scanner specification for the range e The input value is not acceptable Cause A value exceeding the range allowed for an input item was input User response Input a value inside the allowed range Refer to Help of the item or the User s Guide for the correct range e This file cannot be removed because it is specified in other side Cause An attempt was made to remove a file using the dither pattern or gamma download pattern file setting dialog However the file is being used for the other side front side if back side or back side if front side User response Before removing the file change the setting of the other side and then remove e The initial value data file contains an invalid value The standard value is set Cause A value outside the specified range or invalid text was found in the initial value data file the specific item involved is indicated by Entry XXXXX If the file has been modified the setting value for the item may be wrong If the file has not been rewritten the file may have been damaged User response The value is set to a standard value Be sure to check the hard disk chkdsk scandsk and check for computer viruses regularly e The value is higher than the maximum scanning size Either the resolution value or the scanning area has
31. Center 70 Ev eme k kurra 72 8 1 Relevant Image Scanner Specification eese 72 9 2 Maintenance Sel VICO diues ddiude xe iude dude Ludo atate idus lay k day k 87 1 Outline 1 1 Characteristics of this Driver This driver complies with TWAIN regulations V1 8 the latest version as of May 2000 which are global standards for image scanners The driver can be used in all TWAIN compliant applications This driver also supports an image scanner that has the double sided scan function If the application supports continuous scan a double sided document can be scanned 1 2 Operating Environment This driver can be used in the following systems An IBM PC AT compatible machine recommended Intel Pentium 100MHz or higher on which one of the following operating systems are installed Microsoft Windows 95 Microsoft Windows 98 Microsoft Windows Me Microsoft Windows NT Server Version 4 0 Installation of Service Pack 3 or later recommended Microsoft Windows NT Workstation Version 4 0 Installation of Service Pack 3 or later recommended Microsoft Windows 2000 Professional Edition Adaptec SCSI adapter or Fujitsu FMV SCSI adapter In some cases the driver may not operate with the above systems Please check in advance with your place of purchase Notes are provided on the accepted SCSI adapters
32. E E n tri loeo eit E o o The contents of the selected file are displayed Scan button Executes scanning based on the contents of the setting file OK button Ck Terminates without performing the scan operation Adjust button Adjust Switches from the basic scan dialog to the main dialog Help button Help Displays online help Show this dialog next open checkbox e Show this dialog next open If this checkbox 1s checked the Basic Scan Dialog will be opened at the next startup If this checkbox 1s not checked the main dialog will be opened at the next startup 47 4 11 Download Pattern File The download pattern file of this driver 1s a file that defines the patterns to be used by the scanner to execute various image processing This file is available in the following two versions Each version can be selected using the Download Selection Dialog that opens when Download is selected The file is a text file that conforms to the following rules Use an appropriate text editing program for example Note Pad in the operating system to edit the file Dithered download pattern file Any user defined dithered pattern can be used to scan an image by downloading the pattern from the dithered download file to the scanner The defined pattern becomes effective when Download Pattern is selected for Halftone Some models do not support this file See Relevant Image Sc
33. Express the version of this driver by clicking this button 4 6 Setting Scanning Area Specify the scan area in the preview window as follows Setting Press the left mouse button to specify the origin top left corner of the scanning area The cursor appears as a 2 Drag the mouse to show the outline of the scanning area As the cursor moves a range frame 1s shown 3 Release the left mouse button again to set the range bottom right corner of the scanning area Movement 1 Move the cursor into the range frame The cursor appears as a hand 2 Press the left mouse button The cursor changes to a fist 3 Drag the mouse to move the range frame 4 Release the left mouse button to set the current range Cancellation The range frame can be canceled by either of the following ways Click the left mouse button outside the range frame inside the scan document Select other paper types 20 4 7 Setting Options The option dialog is used to set device specific functions and the items that differ depending on whether the scanner used supports them The option specification is divided into Rotation Job Cache Generic and Endorser The supported options depend on the scanner See Relevant Image Scanner Specification in the Appendix SS is displayed for options that cannot be used The option dialog in this driver is explained below The commonly used buttons are explained first
34. The driver is connected to a maximum number of applications supported An operation error occurred An invalid function is specified Unpermitted combination of MSG DG DAT An invalid value is specified An invalid procedure of DG DAT MSG is specified Cause These sub messages are added to the error messages General MSG XXXXX response violation internal and General DAT XXXXX violation internal These sub messages indicate details about the programming errors that occur during message and data processing User response Contact the retail store where the product was purchased or the nearest service center 68 7 1 2 Error messages relating to gamma correction pattern editing Enter a positive decimal value Cause User response A value other than a number has been entered as the gamma correction value Alternatively O or a negative value has been entered Reenter a valid value The file could not be created Cause User response The file for saving could not be created There is insufficient space to save the file or the disk to which the file was to be saved is corrupted Alternatively writing to the directory in which the file was to be saved may not be allowed or other programs relating to disk access may be affecting performance Increase the amount of available space on the disk Use a utility such as chkdsk or scandisk to check the hard disk Ensure that any background programs that access the d
35. a plug in A plug in is an additional program for adding a new function to the application Flmage k Setting Install Setting Sets a plug in in accordance with the following procedure e Pressing the Setting button after selecting a target plug in name in the plug in list displayed displays the plug in setting screen e Pressing the OK button after setting each item reflects the settings for the application to be started Install A new plug in can be installed Press the Install button and specify a file of the plug in to be installed A new plug in is registered in the list Up to 50 plug ins can be registered Setting the Start button gt gt If the scanner being monitored has function keys it is necessary to assign a function key to the start button in advance If no function key has been assigned to the start button a dialog box for determining whether to set the start button 1s displayed when the dialog box is displayed after selecting Option on the pop up menu FUJITSU Scanner Control Center Adapter 1 5 5I ID 5 4D33D dim 2 The start button is not set in the scanner Function key Do you want to set the start button to the function key 59 Selecting Yes displays a dialog box below If No 1s selected the function to start any application when the start button in this application is pressed is disabled The setting of the Start button function k
36. ain order the procedural order is described as follows A B C In accordance with this description operation A is executed first followed by B and C in that order Figures Figures and screen operations in this guide refer to Microsoft Windows 2000 They are also followed when using other operating systems Note that the expressions may vary with the type of scanner connected 1 4 Explanation of terms IPC option board IPC 2 2D in this guide refers to the IPC 2 and IPC 2D image processing circuit IPC 3 3D in this guide refers to the IPC 3 and IPC 3D option board 2 TWAIN 2 1 TWAIN TWAIN is the specification that defines the standard software protocol and application programming interface API for data exchange between a software application program and an image input device such as the image scanner TWAIN development background In the past development of a new scanner inevitably required the development of a compatible driver and a sample demonstration program exclusively designed for the new scanner As the scanner is upgraded the driver may need to be upgraded as well to maintain its compatibility with the upgraded scanner Therefore the use is most likely to be restricted to one specific scanner model to avoid the complication of learning new operation methods and replacing the peripheral driver etc involved in scanner replacement In view of the incompatibility among different scanners an
37. anner Specification in Appendix Although the standard extension of the file name is DTH there may be exceptions Coding configuration n size in the X direction m size in the Y direction pattern value for the X1 Y coordinates pattern value for the X1 Y2 coordinates pattern value for the X1 Y2 coordinates pattern value for the Xn Y m 2 coordinates pattern value for the Xn Y m 1 coordinates pattern value for the Xn Y m coordinates Meaning of each element n size in the X direction indicates the size of the matrix in the X direction Specify 8 for the scanner supported by this driver m size in the Y direction indicates the size of the matrix in the Y direction Specify 8 for the scanner supported by this driver Pattern value for the Xx Y y coordinates contains a values in the range of O bright to 255 dark that specifies the brightness of the X coordinate x and the Y coordinate y Note Use a delimiter other than a number to delimit elements For most cases use a comma 48 Example 8 8 128 128 128 128 128 128 128 128 255 128 128 128 128 128 128 128 255 255 128 128 128 128 128 128 255 255 255 128 128 128 128 128 255 255 255 255 128 128 128 128 255 255 255 255 255 128 128 128 255 255 255 255 255 255 128 128 255 229 LI LI LI LIO 129 49 Gamma download pattern file Any user defined gamma correction processi
38. ay scale Scans data using 256 level monochrome gray scale Light and shade in photographs can be represented with greater fidelity This scanning mode employs far more memory than the Black amp White mode Some versions of the scanner do not support this scanning mode For details contact the retail store where the device was purchased Color Scans data using 24 bits color This mode is suitable for scanning color photograph and employs far more memory that Gray scale mode Some versions of the scanner do not support this scanning mode For details contact the retail store where the device was purchased Automatic separation 14 This option specifies whether to distinguish line drawing from photograph image during scanning If this option is selected the line drawing part is scanned using Black amp White and the photograph part is scanned using halftone This information is most suitable for documents containing both photographs and line drawings or text SEE Selectable edge enhancement Line drawing and photograph image are scanned using halftone Then only line drawing part is highlighted This scanning mode is suitable for emphasizing only characters in the documents that consists of characters and photographs Depending on the model of the scanner this function may not be supported For details refer to Relevant Image Scanner Specification in Section 9 Appendix Black amp White Black White Spec
39. based on the specified Image Mode White Level Follower is used to adjust the density of the white background of a document and correct variations in the background color by compensating the pixels of scanned images individually For ordinary use set White Level Follower to off Use of White Level Follower often increases the background noise because IPC 3 3D is very sensitive This option is not available if Gray Scale is selected for Image Mode In addition some scanner models do not support this option See Relevant Image Scanner Specification in the Appendix 33 Dropout Color Dropout Color Panel setting This option enables scanning excluding the selected color information of green red or blue the three primary colors of light For example to scan black characters framed in red selecting red for scanning will scan only the black characters Reverse Reverse This option specifies whether to reverse the black and white of a scanned image If this option is selected black and white are reversed by reversing the black and white pixels If this option is not selected the black and white values of the reproduced image corresponds to the original image Some applications do not permit normal operation If this occurs contact the manufacturer of the application Advance tFrant Black amp White Static Threshold Gnlor Gray Image Filter Edge Processing v None Empha
40. cable has been connected correctly It is not authorized to write into the folder which is installed FUJITSU Scanner Control Center Can not change the function of the function key Check the Access Authority of the folder which is installed FUJITSU Scanner Control Center Cause While the scanner with function keys are being monitored Access Authority may not have been set to the folder where the FUJITSU scanner Control Center has been installed User response To change the setting of the function key Access Authority of the folder where FUJITSU scanner Control Center has been installed is required Set Access Authority to the folder where FUJITSU scanner Control Center has been installed or execute it with Administrator Authority Scanner 1s not selected Please select a scanner Cause The OK button was pressed without selecting the scanner in the scanner select dialog User response Press the OK button after selecting the scanner to be monitored 71 8 Appendix Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed ADF stacker capacity Document size Supported regular paper Isolation specification Background compensation Contrast setting Gamma pattern Image processing function Interface Job control 8 1 Relevant Image Scanner
41. ct Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed Double sided ADF stacker capacity Document size Supported regular paper Cutout specification Background compensation Contrast setting Gamma pattern Image processing function Interface Job control M3093D3G device name f1 4320 Desktop Reduced optical system Document fixed scanner unit moving flat bed Automatic Document Feeder ADF simultaneous double sided reading Xe discharge tube Green Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 600 400 300 240 200 150 100 dpi With image processing option 50 dpi to 800 dpi at steps of 1 dpi 8 bit 256 levels Enabled 8 bits Dither matrix can be downloaded Error diffusion 1 6 sec or less A4 200 dpi Single sided 27 pages per minute 200 dpi A4 55 kg 22 5 pages per minute 200 dpi A4 55 kg 45 screens per minute Maximum 50 sheets ream weight 55kg A4 High quality paper normal temperature and humidit Maximum 216 mm x 356 mm A4 A5 A5 landscape A6 A6 landscape B5 B6 B6 landscape Letter Legal US Executive Specified one location Enabled 256 steps 3 internal types can be downloaded Automatic binary simple system With image processing opt
42. d peripheral equipment and the accompanying inconvenience there was a demand for standardization of the related hardware and software and TWAIN was established as a result The user may now choose among all the input devices and software driver or application programs conforming to the TWAIN standard and configure a most suitable system for himself without being restricted to the products of a certain series or a certain manufacturer 2 2 TWAIN Application TWAIN mainly applies to the following three software components D Application software Source manager Source The components are related to each other as shown below Application software photo retouching software etc Q Source manager TW AIN DLL TW AIN 32 DLL etc Source Image scanner control of the driver etc Image scanner etc Figure TWAIN Application 3 Installation 3 1 Preparation 1 Check that the operating system is installed correctly 2 Check that the SCSI adapter is connected to the computer 3 Check whether the SCSI driver and ASPI manager are installed correctly and operating For windows 2000 4 60 or later Note Version 4 01 or later of the ASPI Manager is required Use Explorer or a similar program to check the version number of the WNASPI32 DLL file The environment setup tools described later can be used for checking 4 If the previous version was installed first confirm that it has been uninstalled deleted 5 Confirm that
43. designated above Note The printed counter date and time do not always look like the sample because the scanning option takes precedence 30 4 8 Setting Advance Options The advance dialog is used to set items related to image processing The settings apply to device specific functions and items that differ according to whether the scanner used supports them The advance option specification is divided into Color Variance Image Processing and Auto Binary The supported options depend on the scanner See Relevant Image Scanner Specification in the Appendix is displayed for options that cannot be used The option dialog for this driver is explained below The commonly used buttons are explained first OK Makes the new setting valid and closes the option dialog box Cancel Cancel Makes the new setting invalid returns the setting to the previous value and terminates processing Help Help Displays online help 31 The options are described below Advance Front E hs i AIL f E TE Fanel setting Figure Advance dialog density correction Gamma Pattern This option corrects distortions from nonlinear image representation Scanner sensors are generally designed to generate output linear to the density of the light reflected from the document However most output terminals do not produce output that has the desired linear relation to
44. e Scanner Specification in the Appendix 25 E ption Mema Glee Fagy K Dots a uo Figure Option dialog Job Cache Caching Specifies whether to preread cache when a document is scanned This option enables faster scanning If processing of the application being used slows down and scanning stops this option can be used to prevent degradation of the scanning speed The effect however depends on the environment being used None Caching is not performed Read ahead One document page is scanned and the data is preread and stored in PC memory main memory of the personal computer 24 Ram cache d Memory Size 10 _ MB Prereads the allowable amount based on the allocated memory size and stores the data in PC memory A memory size between 1 and 200 MB can be set Use Memory on Scanner Prereads using the memory installed in the scanner displayed only if supported by the scanner Batch Detection Batch Detection None m The application can detect documents on a specific type of form special paper The application must support this function None No detection Scanning is done without change Include and Continue After the special paper is detected scanning continues The data on the special paper is also valid Include and Stop After the special paper is detected scanning stops The data on the special paper is also valid Exclude and Continue After the special paper is d
45. e minimum functions required for scanning The detailed setting functions of the main dialog have been omitted Scanning can be easily performed by selecting a registered setting file The basic scan dialog is also useful for avoiding incorrect operations when standard work is performed By checking the Show this dialog next open checkbox of the Configuration dialog the basic scan dialog box will be opened instead of the main dialog box at the next activation Mn TWAIN Driver Bazit Sean dialog Setting Files ho Gonfiguration lae Decament Sean EIAS Ene Information OK Ene Man gt contig Tits Adjust CPS OMT gt Comftieuration for Document J Tine ota CONE T2334 Help asit Ires clt AA dur Paper eunt gt Ad fe Meo A li m dien zum A e Show this dialog next open Scan Procedure 1 Select the file to be used from the list of setting files 2 Press the Scan button Scanning is performed based on the settings of the setting file information Configuration Setting Files setting Files ho Configuration X for Document A list of setting files is displayed When the desired file is selected the setting information saved in the file will be read and reflected during scanning 46 FTS File Information LES Ele Infosmation Ena Nams gt conr dis Es TORA gt Confisuratiani foc Document me tama gt AUL Darg 73 34 Gasic Mes cutn gt ANT tar Paper Size
46. ecification value from the application Change the specification values Then try scanning again The scanner is in an irregular status fuse is broken etc Please check the scanner status Cause User response A scanner fault such as a blown fuse or foreign matter in the scanning section has occurred Check the scanner status If a fuse has blown replace the fuse If there is foreign matter in the scanning section remove the foreign matter If the error persists contact the retail store where the image scanner was purchased or the nearest maintenance and service center Memory is insufficient Cause User response Insufficient memory for scanning The memory available may be insufficient because an application consuming much GDI memory is operating too many other programs operate at the same time or there are too many registered device drivers The user may mistakenly think that adding more memory will solve this problem However in most cases memory shortage 1s due to insufficient conventional memory called the main memory within 640 kilobytes Checking CONFIG SYS and AUTOEXEC BAT may be a better solution Cancel the registration of device drivers that are irrelevant and make sure that only the absolutely necessary programs are operating Use the memory optimization tool to allocate as much conventional memory as possible An error occurred in the temporary file Cause User response Accessing the int
47. election item 13 Long page front and backside In the same case as that for scanning the front of a long page this option 1s selected in order to scan the entire side of a long page whose length exceeds the vertical size of an A3 sheet If this option is selected the document is scanned in the front to back to front to back order Paper feeding method that is to be supported varies with the type of scanner See Relevant Image Scanner Specification in the Appendix Note To specify duplex scanning the number of copies designated should be based on the number of pages not the number of paper sheets In other words one original with a front and back is regarded as two pages Image Mode Image Made Selects an image mode for scanning the image Select a corresponding image mode from the list Black amp White Scans data by using the fixed threshold binary black and white Distinguishes black from white by the setting in the Threshold of Scanning Parameter This scanning mode is suitable for scanning line drawings and text documents Halftone Dither Scans data using the halftone processing with dithering or error diffusion Uses the patterns set in Halftone to simulate data in black and white Selection of built in dithered patterns or error diffusion not supported by some device models 1s allowed This scanning mode is suitable for scanning images containing light and shadow such as a photograph Gr
48. ep Select one function key which pau want ta set the START amp Fl F2 FS Pressing the OK button after selecting one of function keys from Fl to F3 enables assigning a function key to the start button If the Cancel button is pressed the function key is not assigned to the start button If the Cancel button is pressed the function to start any application when the start button in this application is pressed is disabled Select Scanner When multiple scanners are connected select a scanner to be monitored With this application only one scanner can be monitored at a time If multiple scanners are connected scanner switching is required to monitor the individual scanners Select a scanner to be monitored in the list of scanners to be connected The list is given below Select Scanner Current Device Device M40990 dim Host ID 1 SESI ID 5 EADAPTER 1 ID 5 M4099D dim Selected Device Device Hast ID SESI ID 60 Left clicking the task tray icon displays connected scanner names on the pop up menu It is also possible to select a scanner on this menu Help Displays help information concerning to this application About Displays version information concerning to this application Exit Terminates this application 61 7 Troubleshooting 7 1 Error Messages 7 1 1 Messages from the TWAIN Driver e The input value is outside the range
49. ernal temporary file of the scanned image is causing the error The disk space may be insufficient the temporary file may be damaged or other programs may be affecting disk access Increase the free space of the disk Check the hard disk chkdsk and scandsk Make sure that no other program is accessing the disk If the error message persists contact the retail store where the product was purchased or the nearest service center Download file not found Cause User response A file specified as a dither pattern or gamma pattern cannot be found Check that the download file is in the specified directory Otherwise use the file selection dialog to specify an available file 66 Illegal format or data in download file Cause The format of the specified download file is illegal or the data is incorrect User response User response Use an editor to check file format and data ASPI manager not found Cause The ASPI manager may not have been installed or may have been deleted User response Reinstall the products including the ASPI manager attached to the SCSI board Then reboot the PC Scanner DLL file not found Cause An image scanner was selected but the DLL file of the selected image scanner has not been installed in the directory in which this driver is installed User response Perform the setup again A parameter error has occurred internally The calling procedure is invalid internally The area 1s
50. etected scanning continues The data on the special paper is excluded and will not be transferred to the application Exclude and Stop After the special paper is detected scanning stops The data on the special paper is excluded and will not be transferred to the application 23 Double Feed Detection Double Feed Detection None This option detects a double feed occurs when two or more documents are sent based on the set condition If a double feed is detected when this setting has been turned on the device will stop and an error message output None Double feed detection is not performed Hardware Setting A double feed is detected based on the device setting Check thickness The thickness of the transmitted document is checked by the sensor in the device A double feed is detected by detecting changes in the thickness when more than one document is sent Check length The length of the transmitted document is checked by the sensor in the device A double feed is detected by detecting changes in the length when more than one document is sent Check thickness and length The thickness and length of the transmitted document are checked The detection accuracy can be improved by using Check thickness for continuous scanning of forms that have different lengths and Check length for scanning of forms that have different thicknesses Blank page skip Black Dots Ratio White Dots Ratio This option skips b
51. ge processing is not performed Emphasis This option outputs an image with the edge emphasized Emphasis High Emphasis Mid or Emphasis Low can be selected If Emphasis High is selected the image becomes sharper If Emphasis Low is selected the image appears less distinct 4 De Screen De Screen Level 1 De Screen Level 2 De Screen Level 3 or De Screen Level 4 can be selected This option eliminate moir s patterns To eliminate more effectively higher level is selected White Level Follower White Level Follower Auto Select this option to scan a document whose background color is not white such as a newspaper Select Auto Enable or Disable When Enable is selected the document is scanned using background follow up for line drawings When Disable is selected the document is scanned using the standard basic white background for photographs When Auto is selected the option automatically switches to the optimal setting based on the specified Image Mode White Level Follower is used to adjust the density of the white background of a document and correct variations in the background color by compensating the pixels of scanned images individually Reverse Reverse This option specifies whether to reverse the black and white of a scanned image If this option is selected color data is reversed If this option is not selected the color values of the reproduced image corres
52. he Japanese calendar current or Heisei era The year is printed in the last two digits of the Western calendar An English abbreviation of the month is printed for example JAN for January and FEB for February The month is printed in two digits for example 01 for January and 12 for December The month is printed using one or two digits for example 1 for January and 12 for December The day is printed using two digits for example 03 for the 3rd day of the month and 26 for the 26th day of the month The day is printed using one or two digits for example 3 for the 3rd day of the month and 26 for the 26th day of the month The hour is printed using two digits of the 24 hour clock for example 08 for 8 00 a m and 14 for 2 00 p m The hour is printed using one or two digits of the 24 hour clock for example 8 for 8 00 a m and 14 for 2 00 p m The minute is printed using two digits for example 02 for 8 02 a m and 48 for 2 48 p m The minute is printed using one or two digits for example 2 for 8 02 a m and 48 for 2 48 p m A counter value is printed which increases or decreases with each page The initial counter and the methods of increasing and decreasing values can be specified as explained above under the heading Counter This specification is only permitted at the end of an endorsement string Sample sample 2000 05 18 1911 Displays printed examples of the endorsement string
53. ice See Relevant Image Scanner Specification in Appendix Custom Paper size Setting Width 297 mm X Length a fase mm Cancel Help Figure Custom paper size setting dialog To specify a custom paper size use the slider or enter the paper size directly The applicable unit here is the unit specified under Option Generic Unit Scaling Scanning Area E Scanning i S s IA Lett Width Length fF Fo Ber ns Specifies the start position width and length for the image scan The maximum allowable size 1s the paper size selected previously In addition the minimum size is 1 000 inch 26 millimeters or pixels number of dots per inch according to the unit that has been set Left The left end of the scan area on the scanned document X coordinate Top The top end of the scan area or the scanned document Y coordinate Width The width of the scan area Length The length of the scan area These values are related to one another in the following way 0 lt left end coordinate lt paper width minimum scan area size 0 lt top end coordinate lt paper length minimum scan area size Minimum value width lt paper width left end coordinate Minimum value X length lt paper length top end coordinate 12 Scan Type Scanning Type Selects the feeding device The image scanner uses a document bed called the flat bed as well as an automatic document
54. ied path is correct Cause The setting of the application may be inadequate User response Check setting items of General in Application Dialog and make sure settings are correct and there is no omission If you find any incorrect setting or omission correct it The same Plug in has been installed already Specified Plug in can not install Cause An attempt was made to install the same plug in that has been already installed User response Two or more plug ins assigned to the same name cannot be installed The specified file is not the effective plug in Specified file can not install Can not find the entry point of the specified plug in Specified file can not install Cause The specified file may not be the effective plug in User response Check whether the specified file 1s the effective plug in and retry Exceeded the number of plug in to be supported Can not install the new plug in Cause The number of plug ins to be supported was exceeded User response The maximum number of plug ins that can be supported is 50 Delete unnecessary plug ins in the folder where FUJITSU Scanner Control Center has been installed then install another plug in The plug in has not been installed Cause The check box Use a Plug In was checked but no plug in has been installed User response To use a plug in install a plug in then check the check box Use a Plug In Can not find the application for the Plug in use Can not use the
55. ifies the processing method when Black amp White 1s specified in Image Mode Simple Slice Executes simple binary processing based on the Threshold setting Auto IPC DTC To enable the auto binary function of the image scanner specify this option If this option is selected the Threshold setting will be disabled In addition auto binary has two modes IPC Mode and DTC Mode These modes can be set using the Advance dialog box DTC Mode however is limited to the image processing options Therefore only scanner models that have image processing options support DTC Mode See Relevant Image Scanner Specification in the Appendix Halftone Halftone Dither Pattern Selects the halftone pattern for halftone scanning from the built in pattern list Select the desired halftone pattern for displaying the obtained image This setting is effective when Halftone or Automatic Separation are selected in Image Mode Dither Pattern 0 Executes pattern processing that 1s suitable for scanning a dark photograph Dither Pattern 1 Executes pattern processing that is suitable for scanning a dark colored document containing both text and photographs 15 Dither Pattern 2 Executes pattern processing that is suitable for scanning a light photograph Dither Pattern 3 Executes pattern processing that is suitable for scanning a light colored document containing both text and photographs Download Pattern Executes
56. in Appendix Brightness Sets the brightness of the overall image Specify the brightness with a number in the range of 1 bright to 255 dark To brighten the overall image decrease the value of the setting To darken the overall image increase the value This option corrects distortions from nonlinear image representation Scanner sensors are generally designed to generate output linear to the density of the light reflected from the document However most output terminals do not produce output that has the desired linear relation to the input and the resulting distortion must be corrected An arbitrary range is between 0 1 and 10 0 Color select Golor select f Common setting Color fe Red Green Blue It is possible to select independent value on each color 40 Advance Front xXx Image Mode Color Color Quality Image Emphasis Oh ee De Screen Level 1 C Emphasis High C De Screen Level 2 C Emphasis Mid C De Screen Level 3 C Emphasis Low C De Screen Level 4 Mare White Level Follower Disable Reverse e ETT Cancel Help Figure Advance dialog Quality Image Mode Color selected gt Image Emphasis Mane C De Screen Level 1 C Emphasis High C De Screen Level 2 C Emphasis Mid C De Screen Level 3 Emphasis Low C De Screen Level 4 This option specifies the sharpness of a scanned image Select None De Screen or Emphasis None Ed
57. ion Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Use of FUJITSU Scanner Control Center Disabled An eight megabyte expanded memory option can be loaded in some models This speed is only specified in the scanner itself The actual reading speed may vary depending on the system configuration Not all sizes of paper can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 73 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed ADF stacker capacity Document size Supported regular paper gt Isolation specification Background compensation Contrast setting Gamma patterns Image processing function Interface Job control M3096GX device name fi 4620S Desktop Reduced optical system Document fixed scanner unit moving flat bed Automatic Document Feed ADF Xe discharge tube Green Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi With image processing option 50 dpi to 800 dpi at steps of 1 8 bit 256 levels Enabled 8 bits Dither matrix can be downloaded
58. ire installation of the optional image compression board CMP 2 This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 75 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed Double sided ADF sacker capacity Documnt size Suppored regular paper Cutoutcification Background compensation Contrast setting Gamma pattern Image processing function Interface Job control Long page scanning M3097DG Desktop Reduced optical system Document fixed scanner unit moving flat bed Automatic Document Feed ADF simultaneous double sided reading Xe discharge tube Green Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 600 400 300 240 200 150 100 dpi With image processing option 50 dpi to 800 dpi at steps of 1 dpi 8 bit 256 levels Enabled 8 bits Dither matrix can be downloaded Error diffusion 1 3 seconds or less A4 200 dpi Single sided 36 pages per minute 200 dpi A4 55 kg 30 pages per minute 200 dpi A4 55 kg 60 screens per minute Maxi
59. irection ur to Bottom Back side Counter Counter gt a O SEN Initial Count secum Counter Step nc Dec C Decrease Endorser String String EAAS MMDD AHI NET ur Help sampe 4 2000 05 18 18 11 Figure Option dialog Endorser Enable Endorser e Enable Endorser Specifies enabling or disabling the endorsement function of the device When the option 1s selected and scanning has been completed the scanned originals are printed or a stamp 1s imprinted according to the instructions below This applies only to stamp or endorser options Therefore the function is supported only in devices in which the stamp or endorser option can be installed See Relevant Image Scanner Specification described in the Appendix Y Offset Printing Y Offset ji mm Specifies Y Offset from the edge of the original for the placement of printing See Relevant Image Scanner Specification in the Appendix because the standard value specified here depends on the device 28 Direction Printing Direction ur to Bottom Specifies the direction of endorsement strings When the direction is perpendicular to the direction of scanning designate Up to bottom Only this version of the device permits the direction to be specified Surface Printing eurtace C Front sige e Back side Designa
60. is scanned the light reflected from the pencil lead or ink is not uniform As a result part of the image may be missing If the Ball Point Pen checkbox is checked filtering is applied to offset the bright area in the document and compensate for disconnected or faint lines 37 OCR Smoothing OCR Smoothing This option specifies whether to enable the function that modifies the zigzag lines in the line drawing to smooth curves If this option is selected the smoothing function is enabled For IPC 3 3D either Noise Removal or Smoothing can be selected Noise Removal Noize Removal None This option automatically removes spots that appear as black stains in a white area and spots that appear as white stains in a black area This option uses an algorithm that removes particles from 2 x 2 to 5 x 5 dot matrixes The size of one dot depends on the resolution setting and is equivalent to 1 400 inch for 400 dpi Particles are distinguished from the text by whether they are connected to other dots within the specified number of pixels Noise Removal and Smoothing are valid only for IPC 3 3D Advance Front Black amp White DTG mode Cancel Help Color Gray DTG Density Threshold Curve Rieke Dark Fausto Wee Filtering Ball point pen mode Noise Removal OCR Smoothing None a Figure Advance dialog DTC Mode lt IPC 3 3D and IPC 4D installed gt 38 Advance Front
61. isk are not operating If this error message continues to be displayed contact the place of purchase or your nearest maintenance and service center The file cannot be opened Cause User response The file could not be opened The specified file name may be incorrect or the disk from which it is being read may be corrupted Alternatively the specified file may be a write only file or other programs relating to disk access may be affecting performance If the specified filename is correct use a utility such as chkdsk or scandisk to check the hard disk Ensure that no background programs that access the disk are operating If this error message continues to be displayed contact the place of purchase or your nearest maintenance and service center There 1s a file formatting error Cause User response There is an error in the format of the specified file Either an incorrect file has been specified or the content of the specified file 1s incorrect After checking the users manual check that the content of the specified file is correct 69 7 1 3 Messages concerning to FUJITSU Scanner Control Center Failed to start up the application Check the setting of FUJITSU Scanner Control Center The setting of the path 1s blank Check the setting of FUJITSU Scanner Control Center Can not find the specified file Check if the specified path and file name is correct Can not find the specified work folder Check if the specif
62. kg A4 High quality paper Normal temperature and humidity Maximum 216 mm x 356 mm A4 A4 Landscape A5 A5 Landscape B5 B6 B6 Landscape Letter Legal US Executive Specified one location Enabled 256 steps 3 internal types can be downloaded Automatic binary simple system With image processing option Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 79 Endorser stamp With endorser option Reverse side minimum left margin printing position of 20 mm Maximum number of characters to be printed 20 characters Interface SCSI II Job control Enabled Use of FUJITSU Scanner Control Center Disabled 2 IfO mm is specified as the endorser print position printing will begin 20 mm from the edge of the page 80 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Scanning speed ADF scanning speed ADF stacker capacity Document size Supported regular paper Isolation specification Bac
63. kground compensation Contrast setting Gamma pattern Image processing function M4097D device name fi 4750 Desktop Reduced optical system Document fixed Flat bed Automatic Document Feed ADF simultaneous double sided reading Long page scanning 297mm x 1387mm Xe discharge tube Green Horizontal scanning 400 dpi Vertical scanning 800 700 600 500 400 300 240 200 150 100 dpi Standard 800 700 600 500 400 300 240 200 150 100 dpi With image processing option 50 dpi to 800 dpi at steps of 1dpi 10 bit 1024 levels Enabled 8 bits Dither matrix can be downloaded Error diffusion 0 9 sec or less Single sided 50 pages per minute 200 dpi A4 55 kg Double sided 45 pages per minute 200 dpi A4 55kg 90 screens per minute Maximum 100 sheets ream weight 55 kg A4 High quality paper normal temperature and humidity Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Letter Letter Landscape Double Letter Legal US Executive US Executive Landscape Specified one location Enabled 256 steps 3 internal types can be downloaded Automatic binary simple system With image processing option Outline emphasis Outline extraction SEE Selectable Edge Enhancement Reverse image Automatic binarization Smoothing Filtering Noise removal This speed is only specified for the scanner itself The actual reading speed may var
64. l Bi B x Image Mode Color Color Quality Color select f Common setting Calor f Bed C Green C Blue Shadow Highlight Contrast Brightness Gamma Shadow T Highlight 255 Cancel Help Figure Advance dialog Color Image Mode Color selected Shadow Highlight Shadow 0 Highlight 255 Shadow The highlight allows the darkest part of the document to be controlled The higher the shadow value the darker the image Highlight The highlight allows the brightest part of the document to be controlled The higher the highlight value the lighter the image Any levels on the document outside these settings are flooded all 0 or 255 while the interval between the shadow and highlight settings 1s equally divided into 255 levels which are used to create the output images This means that 1f the shadow and highlight settings are close to each other the contrast for that interval in the scanned document will be very strong but with all other areas maximizing high or low Contrast Brightness Contrast 7 Brightness 255 Contrast Sets the contrast of light and shadow in a scanned image Specify the contrast with a number in the range of 1 low soft to 255 high sharp If this value is 39 increased the dark part of the image is shown darker and the light part is shown lighter Some scanner models do not support this function See Relevant Image Scanner Specification
65. lank pages blank pages or completely black pages during ADF continuous scanning For blank pages use the White Dots Ratio slider to set the skip condition For black pages use the Black Dots Ratio slider to set the skip condition The value displayed to the right of the slider displays the garbage ratio 1 If a scanned document is below this value it is recognized as a blank page The setting range is OFF and 0 2 to 3 0 in increments of 0 2 If blank page skip does not operate properly Ifa blank page is scanned increase the value set If scanning is skipped up to the required document decrease the value set 26 This option is valid only when the cache setting is set to Use Memory on Scanner In addition this option cannot be used unless it 1s supported by the scanner Ratio of black dots included in the scanning area for blank pages Option Figure Option dialog Generic Unit Scaling This option selects the unit for the scanning area and preview window One inch is calculated as 25 4 millimeters When inches are converted to millimeters values are rounded off 2 Note The TWAIN specifications require that the data width be arranged in units of 32 bits Asa result a difference of up to 31 dots can be included depending on the value set Option Rotation Job Gache Endorser Generic K e Enable Endorser Cancel Printing surface Y Offset fo mm C Fut side D
66. lick the Cancel button The character string indicates the data transfer mode used between the driver and the application 18 TWAIN Driver 32 Afer Mode Mative Information NA Scanning O Progress indicator Close OK Close CK Closes the dialog box without scanning If a setting is changed the changed setting is saved in the initial value file Reset Rezet Restores the current setting values to the status immediately after the window is opened Help Help Displays online help When the F1 key is pressed help information regarding the item on which the cursor is placed is displayed Note Depending on the application used help information may not be displayable with the F1 key This is because the driver operation is controlled through the application and the F1 key may be used differently in each application program Help information can be displayed by pressing the F1 key while holding down the Ctrl or Shift key Option Option Displays the option dialog for setting device specific functions See Section 4 7 Setting Option described later 19 Advance Advance Displays the advance dialog for settings related to color variance and image processing Config Config Displays the basic scan dialog for managing the settings file and for setting simple scan dialog switching About About
67. mum 100 sheets ream weight 55 kg A4 High quality paper Normal temperature and humidity Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape Double Letter Letter Letter landscape Legal US Executive US Executive Landscape Specified one location Enabled 256 steps 3 internal types can be downloaded Automatic binary simple system With image processing option Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Enabled front side and both sides This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 76 Use of FUJITSU Scanner Control Center Disabled Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns ADF scanning speed ADF stacker capacity Document size Supported regular paper Cutout specification Background compensation Contrast setting Gamma pattern M3099G M3099GX Desktop Reduced optical system Automatic Document Feed ADF simultaneous double sided
68. ng can be performed by downloading the pattern from the gamma download file to the scanner The defined pattern becomes effective when Download Pattern is selected for Gamma Pattern Some models do not support this file See Relevant Image Scanner Specification in Appendix Although the standard extension of the file name is GMA there may be exceptions Creation of a gamma download pattern file can be facilitated using the following utilities for editing the gamma correction pattern Coding configuration gray scale in the X direction gray scale in the Y direction XO output value X1 output value X2 output value X253 output value X254 output value X255 output value Meaning of each element gray scale in the X direction indicates the size and the gray scale of the input value In this driver this value is fixed at 256 gray scale in the Y direction indicates the size and the gray scale of the output value In this driver this value is fixed at 256 Xx output value indicates the output value in the range of 0 bright to 255 dark for an input value x Note Use a delimiter other than a number to delimit elements For most cases use a comma 50 Example 256 256 255 254 253 252 251 250 249 248 247 246 245 244 243 242 241 240 239 238 237 236 235 234 233 232 231 230 220 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214 21
69. onsibilities for infringements of third parties patents or other rights that may stem from the use of the data in this document Unauthorized reproduction of this document is prohibited Missing or misplaced pages are subject to exchange 88
70. per from inside the device Removing the paper by using excessive force will result in device failure so be careful The hopper tray is open Reinsert the document and close the tray Cause The document tray is open User response For double sided scan close the document tray No paper in the ADF Cause Although ADF was selected as the paper feeding method no paper is found in the document tray User response Select another paper feeding method or set the document in the document tray The hopper tray is open or No paper in the ADF Cause The hopper tray cover is open or there is no paper in the ADF User response Close the hopper tray cover or load paper Insufficient buffer memory size of scanner device for current scanning parameters Please reduce the scanning area or the resolution or install additional memory in the scanner Cause A memory option has not been installed in the image scanner Otherwise a large area or resolution that is not supported by the image scanner has been specified User response Reduce the scanning area or resolution Otherwise install the memory option Refer to the User s Guide of the image scanner for more information 65 The current parameter s 1s are not allowed Please use an other parameter s and try scanning again Cause User response An incorrect value has been specified for the image scanner The problem may be due to an illegal combination with the sp
71. ponds to the original image Some applications do not permit normal operation If this occurs contact the manufacturer of the application 42 4 9 Setting the Configuration Options These options are used to manage the setting files and switch the basic scan dialog display setting File fon Gurrent Setting Contig Press the Config button of the main dialog to open the Configuration dialog box shown below Configuration setting Files loo Current Setting OK EIAS File information Add Ene Man Apt rar LISS ODEN gt Currant GAEE Time Stamp POET 73 14 Help Basic Iresolutreon LSU dor Paper Wre o Ag TUEA r Scanning Area LA CUT ioh Tan YT rent Show this dialog next open Figure Option dialog box simplified DTC Setting Files Setting Files nD Current Setting T The setting information of the scan conditions can be saved in a Setting file Scan condition settings that have been set in advance in this dialog can be selected from the list of setting files This enables selection of all settings at the same time without having to enter the scan conditions one at a time Press the J button to open the list of setting files Subsequent scanning operations can be performed effectively by registering several types of scan conditions that are frequently used 43 FTS File Information Ela Eye information Ene Name DoEpwgernmr ta a o Current ein Inm tarn
72. r question immediately To help us in our effort to provide you with the best maintenance service possible we ask you to kindly write down the following items as many as possible Serial number version and date etc of this product Name and product number of the image scanner being used The options installed on the image scanner being used Manufacturer product name and type number of the computer being used Manufacturer and version of the Windows OS whether Windows has been updated Manufacturer and version of MS DOS Whether MS DOS has been updated Name and version of the display driver Name and version of the printer driver Resolution 1024 x 768 number of colors and number of dots or points of the screen Product name of the SCSI adapter and name and version of the SCSI driver Error occurrence processing the simpler the processing the easier it is to determine the cause Also we would appreciate it very much if you could kindly verify the following items prior to receiving our maintenance service Is the power turned on Is the cable connected correctly Is the correct image scanner driver selected 87 TWAIN Scanner Driver Utility Scanner Utility for Microsoft Windows Users Guide 32 bit version First Edition September 2000 All Rights Reserved Copyright FUJITSU LIMITED 1998 2000 The contents of this document may change for improvements without prior notice Fujitsu takes no resp
73. raph and the gradation are then displayed The values that can be input are integers greater than O or fractions lt lt Formula gt gt Output input 255 x 255 Input 0 255 Free Edit Designates whether to enable editing of the graph area directly using the mouse cursor If this box is checked the gamma pattern input edit box cannot be used and only editing using the mouse cursor is supported Smooth Designates whether to smooth edited curves This setting is only valid when Free Edit is selected In this setting the curved lines drawn by the mouse are automatically smoothed This is reflected in the graph and gradation display Reverse Designates whether to reverse black and white When this box is checked the current output values are converted to 255 output values 55 6 How to Use the FUJITSU Scanner Control Center 6 1 Outline This software that is resident in the system continuously monitors the scanner connected and starts the target application in response to an instruction from the operation panel in the scanner Pressing the start button on the scanner starts the application that has been set in advance For applicable models see Relevant Image Scanner Specification in the Appendix 6 2 How to Start the FUJITSU Scanner Control Center Select as follows Start Program Scanner Utility for Microsoft Windows then FUJITSU Scanner Control Center If this application is started it i
74. s stationed in the system then an icon is displayed on the task tray An icon indication changes to show how the scanner is connected as follows 1 The scanner can be used 2 The scanner power is turned off and not connected a 56 Right clicking the icon displays the following pop up menu Hescan Scanner Option Select Scanner Help About Exit Left clicking the icon displays the scanner being connected as shown below The scanner that has been monitored by this application is indicated with a check mark PTE IT Rie uk TN Don v MAD Odm Lo 6 3 Pop up Menu Rescan Scanner Rescans the scanner that is currently connected A scanner that is not recognized by the OS cannot be found even though it is rescanned Option Sets up the application to be started when the start button of the scanner is pressed 57 BE Hetan Path Specifies a file name of the application to be started with its absolute pathname A file can be also selected directly by using the button Argument Specifies an argument to be passed when starting the specified application This item can be omitted Start in Specifies a default folder for starting the application A default folder can be also selected by using the button This parameter can be omitted Run Specifies the display size of the application to be started 58 Use Plug In Checking this check box specifies
75. sis High C Edge Extract Emphasis Mid smooth ine C Emphasis Low Backeround Removal Mirror Image Mirror 3b TU Tet Misses Re roo ae Wes arare 2 ku Deity Hieht Figure Advance dialog image processing 34 Edge Processing f Mone C Emphasis High Edge Extract Emphasis Mid c Smoothing C Emphasis Low Backeround Removal This option specifies the sharpness of a scanned image Select None Edge Extract or Smoothing Background Removal None Edge processing is not performed Edge Extract This option outputs an image with the edge extracted If this option is selected the boundary between the black part and white part in a closed area 1s traced and the edge extracted DTC Variance and Edge Extract are mutually exclusive Smoothing This option smoothes the curves in an image by removing zigzag lines Emphasis This option outputs an image with the edge emphasized Emphasis High Emphasis Mid or Emphasis Low can be selected If Emphasis High is selected the image becomes sharper If Emphasis Low is selected the image appears less distinct Mirror Mirror This option specifies whether to flip the scanned image over the scanning axis If this option is selected a mirror image of the original image is obtained Variance Simple auto binary DTG Variance JE Lowy Hight This option specifies the value for adjusting the dynamic threshold of an
76. tered trademarks of Microsoft Corporation IBM PC AT and DOS V are registered trademark of International Business Machine Corporation Adaptec is a registered trademark of Adaptec Inc EZ SCSI is a trademark of Adaptec Inc Other product names are the trademarks or registered trademarks of the respective companies ii Organization This manual explains how to install and use this driver and how to use the TWAIN scanning utility TWAIN This section gives an overview of the TWAIN specification Installation This section explains the procedure for installing the environments in which this driver may operate Using the Driver This section explains how to use the driver Using the Utilities Use of the following utilities 1s explained Using the Gamma Pattern Editor Troubleshooting This section explains the possible causes of error messages and operation errors and the corresponding recommended actions Appendix The appendix contains the specifications of image scanners iii Contents pem 1 AS Oharacteristics or This DIME a a a xan a en b ctae 1 12 Operatirid ENVIO AMO diaria A E ua meron 1 RA INDIOS yeee Bedeneke O y e Ree 0029062700 2006 ed XM aUo OT OUI K r vee y 2 1 24 ExDlAnaNO O TOL S sorrisi k n allen il 3 2 TWAIN Si 4 2 p NANI a E UE 4 ae WAT AICA O a a lid 4 3 Il Slall a mM 6 o IIR pd 7212 6 ney KEK OK KN Re ener MM LE 6 32 tarnung la Sile iia 6 ce Po A PP e 7
77. tes the side for printing or stamp imprinting If the side is opposite the scanned surface select Back Select Front for the scanned surface If both sides are scanned the side scanned first 1s considered to be the Front See Relevant Image Scanner Specification in the Appendix because the available options depend on the device Initial Count Counter Initial Count ji Designates the initial count when the endorsement string is set including a counter value Programmable values range from 0 to 65535 Counter Step Counter Counter Step linc Dec Designates the counter increment of the set counter values In other words this value is added to or subtracted from the counter each time one original is scanned An increment of 0 1 or 2 may be specified Usually 1 1s designated for a single sided original and 2 for a double sided original Counter Counter Counter t Increase Decrease Designates whether to increase or decrease the specified step value 20 Endorsement String String err AM MSDC SHINN 1H Specifies the endorsement string The following definitions can be used They may also be selected from the menu which is displayed by clicking on gt 2o Y Y Y Y 2o Y Y Y O6 Y Y MMM MM M DD D HH H NN N 05ud The year is printed in four digits using the Western calendar The year is printed using the two digits of t
78. ty Document size Supported regular paper Isolation specification Background compensation Contrast setting Gamma pattern Image processing function Interface Job control M3097G Desktop Reduced optical system Document fixed scanner unit moving flat bed Automatic Document Feed ADF Fluorescent tube Green Horizontal scanning 400 dpi Vertical scanning 400 300 240 200 dpi Standard 400 300 240 200 dpi With image processing option 50 dpi to 1 600 dpi at steps of 1 8 bit 256 levels Enabled 8 bits Some release version of scanner do not support gray scale output format Dither matrix can be downloaded Error diffusion 1 3 sec or less A4 200 dpi 3 7 sec or less A3 400 dpi 36 pages minute 200 dpi A4 55 kg Maximum 100 sheets ream weight 55 kg A4 High quality paper Normal temperature and humidity Maximum 297 mm x 432 mm A3 A4 A4 Landscape A5 A5 Landscape A6 A6 Landscape B4 B5 B5 Landscape B6 B6 Landscape Letter Letter Landscape Double Letter Legal US Executive US Executive Landscape Specified one location Enabled 256 steps 3 internal types can be downloaded Auto binary simplified method Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal SCSI II Enabled Use of FUJITSU Scanner Control Center Disabled Use of this scanner may requ
79. wnloaded Automatic binary simple system With image processing option Outline emphasis Outline extraction Automatic separation Mirror image Reverse image Automatic binarization Smoothing Filtering Noise removal 1 This speed is only specified for the scanner itself The actual reading speed may vary depending on the system configuration 2 Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 85 Endorser stamp With endorser option Reverse side minimum left margin printing position of 20 mm f Maximum number of characters to be printed 30 characters Interface SCSI II Online offset adjustment Enabled Job control Enabled Automatic skew compensation Enabled Drop out Enabled Double feed detection Enabled Buffer scan cache using scanner memory function Enabled Blank page skip Enabled only when scanner memory is used Use of FUJITSU Scanner Control Center Enabled 2 IfO mm is specified as the endorser print position printing will begin 20 mm from the edge of the page 86 8 2 Maintenance Service This section explains briefly how you can help us to provide you with high quality maintenance service Since it is practically impossible for the Fujitsu service staff to be aware of every detail of your daily scanning operation please understand that our staff may sometimes be unable to answer you
80. y depending on the system configuration Not all paper sizes can be used in all devices For details refer to the users manual for the device For other paper sizes the customer settings can be used 81 Interface SCSI II Job control Enabled Double feed detection Enabled Long page scanning Enabled front side and both sides Use of FUJITSU Scanner Control Center Enabled 82 Product Type Image sensor Operating method Light source Basic resolution Output resolution Grayscale levels internal Grayscale output Halftone Patterns Color Scanning speed ADF scanning speed ADF stacker capacity Document size Supported regular paper Isolation specification Background compensation Contrast setting Gamma pattern fi 4750C Desktop LED RGB Reduced optical system Document fixed Flat bed Automatic Document Feed ADF simultaneous double sided reading Long page scanning 297mmx1387mm LED R G B Horizontal scanning 400 dpi Vertical scanning 800 700 600 500 400 300 240 200 150 100 dpi Standard 800 700 600 500 400 300 240 200 150 100 dpi With image processing option 50 dpi to 800 dpi at steps of 1dpi 10 bit 1024 levels Enabled 8 bits Dither matrix can be downloaded Error diffusion 24bit B W 0 9 sec or less Color 3 1 sec or less B W Single sided 50 pages per minute 200 dpi A4 55 kg Double sided 45 pages per minute 2

Fujitsu C150-E187-01EN Scanner User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents