Fujitsu C120-E361-04EN Server User Manual
Contents
1. CO pa RA me Figure 1 9 RCI branching connector connection of a midrange server 5 1 LJ a B 7 5 o aya a 2 Figure 1 10 RCI branching connector connection of a high end server ETHERNET E D Pi ln 1 J ula ACTIVE 3 Connect the RCI terminating resistor to the branching connector that is at the end of the RCI connection C120 E361 04EN 1 11 A 1 Appendix A Troubleshooting This appendix explains how to deal with possible problems during the RCI setup In the Case Where Setrci Command Ended Abnormally and Displayed Operation Failed Error Status XX In the Case Where RCI Status of RCI Host Changes From ACTIVE to INACTIVE In the Case Where Setrci Command Ended Abnormally and Displayed Operation Failed Error Status XX When the RCI construction by the setrci command ended abnormally and Operation failed error status XX is displayed the displayed error status code explanation and remedy pattern are described to the following table Table A 1 The Error Status Code and Explanation Code Explanation Remedy pattarn 00 Detected the duplicate RCI address Pattern A 01 RCI address of current unit is not configured or false Pattern B 02 Detected the duplicate2. address OOOf7fff Inactive The command completed successfully 3 Verify that the RCI address is 000f7fff Remarks 000f7fff is the default value of the RCI address If the default value is not set execute the setrci c init command to initialize the value If the system is powered off you can use the setrci c init command XSCF gt setrci c init The command completed successfully 4 Connect main unit B which is to be added with an RCI cable see Figure 1 8 Connect an RCI branching connector to each of the RCI ports and connect them with RCI cables by using a daisy chain connection Connect an RCI terminating resistor to the branching connector at either end of the RCI connection Refer to Section 1 3 5 Connection of RCI 5 Turn on the AC input to all the RCI device which are in the RCI connection 6 On main unit B execute the setrci c set command to make the settings of the host node Since the main unit is the second unit host_no is 2 C120 E361 04EN 1 9 CHAPTER 1 RCI Build Procedure 1 3 5 XSCF gt setrci c set 2 The command completed successfully Execute the setrci c addconfig command on main unit B to expand the RCI configuration XSCF gt setrci c addconfig The command completed successfully Display the RCI status by executing the setrci c statcommand on main unit A XSCF gt setrci c stat HOST address 000102ff Active LIST address pwr alm I F sys phase ctg
3. Check the RCI setup procedure the RCI address value and the connection 1 Check the setting of the RCI address and the duplicate of the RCI address by setrci c stat command 2 Check whether the othr RCI host that doesn t execute the RCI initialization is connected 2 Inthe case of anomaly retry RCI setup in correct procedure e Pattern B Check the RCI address value of current unit by setrci c stat command 2 Inthe case of anomaly retry RCI setup in correct procedure e Pattern C 1 Check the RCI address value of current unit and other unit by setrci c stat command 2 Inthe case of anomaly retry RCI setup in correct procedure e Pattern D Check whether 95 and more units of RCI I O unit include the External power controller are not connected 2 When 95 and more units are connected change the connection configuration to 94 and less units include the External power controller and retry RCI setup Pattern E Replace the XSCF board 2 After the replacement of the XSCF unit retry RCI setup e Pattern F Check whether RCI address value of the Line selector switch is not duplicated 2 Ifthe duplicate change the RCI address of the Line selector switch and retry RCI setup To change the RCI address of the Line selector switch refer to its manuals e Pattern G Check the state of XSCF and execute either of the following operations When XSCF reboot or redundancy are working execute the setrci command after these ar
4. E327 SPARC Enterprise M4000 M5000 Servers Installation Guide C120 E351 SPARC Enterprise M8000 M9000 Servers Installation Guide C120 E328 SPARC Enterprise M4000 M5000 Servers Service Manual C120 E352 SPARC Enterprise M8000 M9000 Servers Service Manual C120 E330 External I O Expansion Unit Installation and Service Manual C120 E329 SPARC Enterprise M4000 M5000 M8000 M9000 Servers RCI Build Procedure C120 E361 SPARC Enterprise M4000 M5000 M8000 M9000 Servers Administration Guide C120 E331 SPARC Enterprise M4000 M5000 M8000 M9000 Servers XSCF User s Guide C120 E332 SPARC Enterprise M4000 M5000 M8000 M9000 Servers XSCF Reference Manual C120 E333 SPARC Enterprise M4000 M5000 M8000 M9000 Servers Dynamic Reconfiguration C120 E335 DR User s Guide SPARC Enterprise M4000 M5000 M8000 M9000 Servers Capacity on Demand COD C120 E336 User s Guide SPARC Enterprise M4000 M5000 M8000 M9000 Servers RCI User s Guide C120 E360 SPARC Enterprise M4000 M5000 Servers Product Notes Go to the Web SPARC Enterprise M8000 M9000 Servers Product Notes Go to the Web External I O Expansion Unit Product Notes C120 E456 a Manuals on the Web The latest versions of all the SPARC Enterprise Series manuals are available at the following websites Global Site http www fujitsu com sparcenterprise manual Japanese Site http primeserver fujitsu com sparcenterprise manual Note Product Notes and Release Notes are available on the website only Please check for
5. IF MAILED IN THE UNITED STATES FOLD AND TAPE vi C120 E361 04EN Contents Pr face cia nia ee que ade ae ee eee dada tees cece teks redd i Reader s Comment Form 0000 cece eee nn nn hn v CHAPTER 1RCI Build Procedure eser 1 1 1 1 RCEOVENIEW xps buc peii el abu antennes 1 1 1 1 1 Overview of RCI connection aaa aaaea eee 1 1 1 2 RGl commiahd 5b eb eb ee a ALE a en 1 3 1 2 1 C mmandhlist culata mr EE ez e are dte 1 3 1 3 RG Setup ix uam asa m Ies ELT ehe t etis 1 4 1 3 1 New setup for a single RCI Host and two RCI I O units 1 4 1 3 2 New setup of two RCI Hosts eee 1 6 1 3 3 When an RCI I O unit is added later 1 8 1 3 4 When a RCI Host is added later 2 ccm 1 9 1 3 5 Connection of RGI uus toa ras ee a are 1 10 Appendix ATroubleshooting eene A 1 A 1 In the Case Where Setrci Command Ended Abnormally and Displayed Operation Failed Error Status XA a wel ie cal alan Aiea Re eee at De wot Pa teal A 1 A 2 Inthe Case Where RCI Status of RCI Host Changes From ACTIVE to INACTIVE A 4 C120 E361 04EN vii Contents viii C120 E361 04EN Contents Figures Figure 1 1 Basic configuration neee 1 1 Figure 1 2 Cluster configuration neee 1 2 Figure 1 3 Duplicated configuration eneen 1 2 Figure 1 4 Mixture of duplicated and unduplicated configurations 1 2 Figure 1 5 New setup
6. and Contents of This Manual This manual is organized as described below Chapter 1 RCI Build Procedure Explains the initial build procedure of the Remote Cabinet Interface RCI in the installation work Appendix A Troubleshooting Explains how to deal with possible problems during the RCI setup C120 E361 04EN Preface SPARC Enterprise Mx000 Servers Documentation The manuals listed below are provided for reference Book Titles Manual Codes SPARC Enterprise M4000 M5000 Servers Site Planning Guide C120 H015 SPARC Enterprise M8000 M9000 Servers Site Planning Guide C120 H014 SPARC Enterprise Equipment Rack Mounting Guide C120 H016 SPARC Enterprise M4000 M5000 Servers Getting Started Guide C120 E345 SPARC Enterprise M8000 M9000 Servers Getting Started Guide C120 E323 SPARC Enterprise M4000 M5000 Servers Overview Guide C120 E346 SPARC Enterprise M8000 M9000 Servers Overview Guide C120 E324 Important Safety Information for Hardware Systems C120 E391 SPARC Enterprise M4000 M5000 Servers Safety and Compliance Guide C120 E348 SPARC Enterprise M8000 M9000 Servers Safety and Compliance Guide C120 E326 External I O Expansion Unit Safety and Compliance Guide C120 E457 SPARC Enterprise M4000 Server Unpacking Guide C120 E349 SPARC Enterprise M5000 Server Unpacking Guide C120 E350 SPARC Enterprise M8000 M9000 Servers Unpacking Guide C120
7. are used under license e Ethernet is a registered trademark of Xerox Corporation in the United States and in certain other countries All SPARC trademarks are registered trademarks of SPARC International Inc Products bearing the SPARC trademarks are based on an architecture developed by Sun Microsystems Inc e All other product names mentioned herein are the trademarks or registered trademarks of their respective owners System and product names in this manual are not always noted with trademark or registered trademark symbols The contents of this manual may be revised without prior notice The contents of this manual shall not be disclosed in any way or reproduced in any media without the express written permission of Fujitsu Limited All Rights Reserved Copyright FUJITSU LIMITED 2007 C120 E361 04EN Preface This manual explains the RCI build procedure of the SPARC Enterprise M4000 M5000 M8000 M9000 server This manual is intended for authorized service personnel who perform maintenance work of the server or field engineers In this manual the verification ofthe standalone operation of the server is assumed to have been completed Read this manual together with the reference manuals cited in it This manual explains the following Structure and Contents of This Manual SPARC Enterprise Mx000 Servers Documentation Text Conventions Prompt Notations Syntax ofthe Command Line Interface CLI Structure
8. for a single RCI Host and two RCI I O units 1 4 Figure 1 6 New setup of two RCI Hosts eee 1 6 Figure 1 7 When an RCI I O unit is added later en 1 8 Figure 1 8 When a RCI Hosts is added later eee 1 9 Figure 1 9 RCI branching connector connection of a midrange server 1 11 Figure 1 10 RCI branching connector connection of a high end server 1 11 C120 E361 04EN ix Contents x C120 E361 04EN Contents Tables Table 1 1 Command list en 1 3 Table A 1The Error Status Code and Explanation eeen A 1 C120 E361 04EN xi CHAPTER 1 RCI Build Procedure This chapter explains the following items regarding the initial build procedure of the Remote Cabinet Interface RCI in the installation work RCI Overview RCI command RCI Setup 1 1 RCI Overview RCI is an interface to connect RCI Host general name for main units supporting RCI and for RCI I O units In this manual a base cabinet and an I O unit that support the RCI are referred to as an RCI Host and an RCI I O unit respectively Furthermore RCI Hosts and RCI I O units are generally referred to as RCI device To connect RCI VO units or to use the RCI asynchronous monitoring functions for an FJ cluster a setup using the RCI setup commands is required in addition to the connection with RCI cables 1 1 1 Overview of RCI connection There are two types of main unit midrange servers equipped with one RCI and high end servers equipped
9. on screen computer User Name jsmith output Privileges useradm This font represents the example of auditadm command input in the frame Italic Indicates the name of a reference manua See the XSCF User s Guide Indicates names of chapters sections See Chapter 2 Preparation for items buttons or menus Installation C120 E361 04EN iii Preface Prompt Notations The notation used for prompts in this manual is shown below Syntax ofthe Command Line Interface CLI Shell Prompt notation XSCF XSCF gt C shell machine name C shell superuser machine name Bourne shell and Korn shell Bourne shell and Korn shell super users OpenBoot PROM ok Syntax of the Command Line Interface CLI The command syntax is described below Command syntax The command syntax is as follows A variable that requires input of a value is enclosed in lt gt An optional element is enclosed in A group of options for an optional keyword is enclosed in and delimited by A group of options for a mandatory keyword is enclosed in and delimited by The command syntax is shown in a frame Example XSCF gt showuser a C120 E361 04EN Reader s Comment Form Reader s Comment Form We would appreciate your comments and suggestions for improving this publication Date Publication No Your Name Publication Name Company Address City St
10. the recent update on your product C120 E361 04EN Preface b Documentation CD For the Documentation CD please contact your local sales representative SPARC Enterprise M4000 M5000 Servers Documentation CD C120 E365 SPARC Enterprise M8000 M9000 Servers Documentation CD C120 E364 c Manual included on the Enhanced Support Facility x x CD ROM disk Remote maintenance service Book Titles Manual Codes Enhanced Support Facility User s Guide for REMCS C112 B067 d Provided in system Man page of the XSCF Note The man page can be referenced on the XSCF Shell and it provides the same content as the SPARC Enterprise M4000 M5000 M8000 M9000 Servers XSCF Reference Manual e Solaris Operating System related manuals http docs sun com f Information on Using the RCI function For information on using the RCI function refer to the SPARC Enterprise M4000 M5000 M8000 M9000 Servers RCI Build Procedure This manual and SPARC Enterprise M4000 M5000 M8000 M9000 Servers RCI User s Guide provided on the website Text Conventions This manual uses the following fonts and symbols to express specific types of information Typeface or symbol Meaning Example AaBbCc123 What you type when contrasted XSCF gt adduser jsmith with on screen computer output This font represents the example of command input in the frame AaBbCc123 The names of commands files and XSCF gt showuser p directories
11. 4 003002ff OFF ACT power off disk 0400 04 The command completed successfully 9 Verify that all the RCI device in the RCI connection are incorporated C120 E361 04EN 1 5 CHAPTER 1 RCI Build Procedure 1 3 2 New setup of two RCI Hosts Host A Host B RCI I O unit RCI I O unit Figure 1 6 New setup of two RCI Hosts l Log into the XSCF Shell 2 On main unit A execute the setrci c stat command to display the RCI status XSCF gt setrci c stat HOST address OOOf7fff Inactive The command completed successfully UJ Verify that the RCI address is O00f 7fff Remarks 000f7fff is the default value of the RCI address If the default value is not set execute the setrci c init command to initialize the value If the system is powered off you can use the setrci c init command XSCF gt setrci c init The command completed successfully 4 Ina similar manner display the RCI status of main unit B to verify that the RCI address is 000f7fff 5 Connect the main unit and I O units with RCI cables see Figure 1 6 Connect an RCI branching connector to each of the RCI ports and connect them with RCI cables by using a daisy chain connection Connect an RCI terminating resistor to the branching connector at either end of the RCI connection Refer to Section 1 3 5 Connection of RCI 6 Turn on the AC input to all the RCI device which are in the RCI connection 1 6 C120 E361 04EN 1 3
12. Inactive The command completed successfully 3 Verify that the RCI address is 000f7fff Remarks OOOf7fff is the default value of the RCI address If the default value is not set execute the setrci c init command to initialize the value If the system is powered off you can use the setrci c init command 1 4 C120 E361 04EN 1 3 RCI Setup XSCP gt setrci c init The command completed successfully 4 Connect the main unit and I O units with RCI cables see Figure 1 5 Connect an RCI branching connector to each of the RCI ports and connect them with RCI cables by using a daisy chain connection Connect an RCI terminating resistor to the branching connector at either end of the RCI connection Refer to Section 1 3 5 Connection of RCI 5 Turn on the AC input to all the RCI device which are in the RCI connection 6 Execute the setrci c set command to make the settings of the host node Since the main unit is the first unit host no is 1 XSCP gt setrci c set 1 The command completed successfully 7 Execute the setrci c initconfig command to configure the RCI XSCF gt setrci c initconfig The command completed successfully 8 Execute the setrci c stat command to display the RCI status XSCP gt setrci c stat HOST address 000101ff Active LIST address pwr alm I F sys phase ctgry dev cls sub cls tm out 000101ff OFF ACT power off host 0001 Ob 003001ff OFF ACT power off disk 0400 0
13. RCI I O unit is added later l Connect the I O unit to be added with an RCI cable by using a daisy chain connection see Figure 1 7 Connect an RCI branching connector to the RCI port and then connect it with an RCI cable by using a daisy chain connection Connect an RCI terminating resistor to the branching connector at either end of the RCI connection Refer to Section 1 3 5 Connection of RCI 2 Turn on the AC input to all the units which are in the RCI connection 3 Log in to the XSCF Shell 4 Execute the setrci c addconfig command to configure the RCI XSCF gt setrci c addconfig The command completed successfully 5 Execute the setrci c stat command to display the RCI status XSCF gt setrci c stat HOST address 000101ff Active LIST address pwr alm I F sys phase ctgry dev cls sub cls tm out 000101ff OFF ACT host 0001 Oa 003001ff OFF ACT disk 0400 04 003002ff OFF ACT disk 0400 04 The command completed successfully O Verify that the added I O unit is incorporated 1 8 C120 E361 04EN 1 3 RCI Setup 1 3 4 When a RCI Host is added later TE ee 7 RCI aci Host A Host B M gt al R Addition RCI I O unit RCI I O unit 4 Figure 1 8 When a RCI Hosts is added later 1 Log into the XSCF Shell 2 On main unit B which is to be added execute the setrci c stat command to display the RCI status XSCF gt setrci c stat HOST
14. RCI Setup 7 On main unit A execute the setrci c set command to make the settings of the host node Since main unit A is the first unit host_no is 1 XSCP gt setrci c set 1 The command completed successfully 8 On main unit B execute the setrci c set command to make the settings of the host node Since main unit B is the second unit host_no is 2 XSCP gt setrci c set 2 The command completed successfully 9 On main unit A execute the setrci c initconfig command to configure the RCI XSCF gt setrci c initconfig The command completed successfully 10 Execute the setrci c addconfigcommand on main unit B to expand the RCI configuration XSCF gt setrci c addconfig The command completed successfully ll Display the RCI status by executing the setrci c stat command on main unit A XSCP gt setrci c stat HOST address 000101ff Active LIST address pwr alm I F sys phase ctgry dev cls sub cls tm out 000101ff OFF ACT host 0001 Ob 000102ff OFF ACT host 0001 Ob 003001ff OFF ACT disk 0400 04 003002ff OFF ACT disk 0400 04 The command completed successfully 12 Verify that all the RCI device in the RCI connection are incorporated C120 E361 04EN 1 7 CHAPTER 1 RCI Build Procedure 1 3 3 When an RCI I O unit is added later RCI Host ET TTT Addition RE rd El RCI I O unit RCI I O unit Figure 1 7 When an
15. RCI address of RCI host or detected the Pattern C undefined RCI address 03 RCI address of current unit is not configured Pattern B 04 Over maximum entry of RCI table Pattern D 05 Detected anomaly in RCI table receiving Pattern C 06 Detected anomaly in RCI table sending Pattern C 07 Receiving status check from undefined RCI device Pattern C 08 Detected the loss of RCI master Pattern C 09 Detected anomaly of RCI table Pattern C 0a Synchronous time out of RCI table Pattern C 0b Synchronous retry out of RCI table Pattern C Oc Detected anomaly of RCI table Pattern C Od Failed the version check of RCI table Pattern C Oe Detected anomaly of RCI table Pattern C Of Detected anomaly in synchronous with RCI Neuron chip Pattern E C120 E361 04EN A 1 Appendix A Troubleshooting A 2 Table A 1 The Error Status Code and Explanation Code Explanation Remedy pattarn 20 Detected the duplicate RCI address in RCI I O unit Expansion file Pattern C unit External power controller 30 Detected the duplicate RCI address in RCI I O unit Line selector Pattern F switch fd RCI construction cannot be constructed or it was cancelled Pattern G fe Other RCI unit is constructing the RCI network Pattern A ff RCI setup procedure is false Pattern A C120 E361 04EN A 1 In the Case Where Setrci Command Ended Abnormally and Displayed Operation Failed Error Status XX Remedy pattarn Pattern A 1
16. ate Zip Phone Email address Your Comments Comments Reply requested o Yes o No Please evaluate the overall quality of this manual by checking v the appropriate boxes Good Fair Poor Good Fair Poor Good Fair Poor Organization o o o Use of examples o o o Legibility o 0 o Accuracy o 0 o Index coverage o o o Binding o 0 o Clarity o o O Cross Figures and tables o o o Overall rating of referencing o o O General appearance o o o this publication o 0 O Technical level o Too detailed o Appropriate o Not enough detail All comments and suggestions become the property of Fujitsu Limited For Users in U S A Canada For Users in Other Countries and Mexico Fax this form to the number below or send this form Fold and fasten as shown on back to the address below No postage necessary if mailed in U S A Fujitsu Computer Systems Fujitsu Learning Media Limited Attention Engineering Ops M S 249 FAX 81 3 3730 3702 1250 East Arques Avenue 37 10 Nishi Kamata 7 chome P O Box 3470 Oota Ku Sunnyvale CA 94088 3470 Tokyo 144 0051 FAX 408 746 6813 JAPAN FUJITSU LIMITED C120 E361 04EN V Reader s Comment Form FOLD AND TAPE BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 741 SUNNYVALE CA POSTAGE WILL BE PAID BY ADDRESSEE co FUJITSU FUJITSU COMPUTER SYSTEMS AT TENTION ENGINEERING OPS M S 249 1250 EAST ARQUES AVENUE P O BOX 3470 SUNNYVALE CA 94088 3470 NO POSTAGE NECESSARY
17. co FUJITSU SPARC Enterprise M4000 M5000 M8000 M9000 servers C120 E361 04EN C120 E361 04EN SPARC Enterprise M4000 M5000 M8000 M9000 Server RCI Build Procedure co FUJITSU ABOUT THIS PRODUCT This product is designed and manufactured for use in standard applications such as office work personal device household appliance and general industrial applications This product is not intended for use in nuclear reactor control systems aeronautical and space systems air traffic control systems mass transportation control systems medical devices for life support missile launch control systems or other specialized uses in which extremely high levels of reliability are required the required levels of safety cannot be guaranteed or a failure or operational error could be life threatening or could cause physical injury referred to hereafter as high risk use You shall not use this product without securing the sufficient safety required for high risk use If you wish to use this product for high risk use please consult with sales representatives in charge before such use TRADEMARK ACKNOWLEDGEMENTS e UNIX is a registered trademark of The Open Group in the United States and other countries licensed exclusively through X Open Company Limited e Sun Sun Microsystems the Sun Logo Solaris and all Solaris based marks and logos are trademarks or registered trademarks of Sun Microsystems Inc in the U S and other countries and
18. e completed If the above mentioned doesn t correspond retry the setrci command C120 E361 04EN A 3 Appendix A Troubleshooting A 2 A 4 In the Case Where RCI Status of RCI Host Changes From ACTIVE to INACTIVE Remarks When this problem has occurred do not replace the XSCF unit because it is not a failure of the XSCF unit This problem is occurred by the mistake of the RCI construction procedure and the RCI connection t occurrs when the same RCI address is set and constructed or when connecting with the RCI network of the construction of the RCI host that has not been initialized Confirm whether to correspond to this problem The procedure is the following Excute showlogs command and check whether RCI configuration conflict is generated in error log When that message was generated check the RCI establishment procedure the RCI address value and the connection In the case of anomaly correct the RCI address or the connection of relevant device according to the change procedure of each device Refer to Chapter 1 3 4 When a RCI Host is added later and retry RCI establishment C120 E361 04EN co FUJITSU
19. ry dev cls sub cls tm out 000101ff OFF ACT host 0001 Ob 000102ff OFF ACT host 0001 Ob 003001ff OFF ACT disk 0400 04 003002ff OFF ACT disk 0400 04 The command completed successfully Verify that the added main unit is incorporated Connection of RCI According to the following procedure connect different units with RCI cables by using a daisy chain connection Prepare RCI branching connectors and RCI terminating resistors All of them are supplied with the main unit Connect the main unit and I O units with RCI cables see Figure 1 9 and Figure 1 10 1 Connect the RCI branching connector 1 to the RCIport on an XSCF unit of the main unit 2 Connect the RCI branching connector and the RCI port of an I O unit with an RCI cable 2 by using a daisy chain connection C120 E361 04EN 1 3 RCI Setup Remarks Up to 32 RCIs including the RCI main unit can be connected Use the repeater function of the external power controller to extend the cable length used and to increase the number of connected RCI device Note that the maximum RCI cable length is 150 meters Remarks The external power controller is included in the number of RCI device EF 19 OSO o
20. ve been made correctly setrci c init Initializes the RCI configuration information If other host units are connected through the RCI the RCI settings must be initialized on each host unit You can use this command if the system is powered off setrci c set host_no Sets up an RCI Host node Before this command can be executed the RCI settings must already have been initialized host_noAF Integer numbers from 1 to 32 are assigned in this order setrci c initconfig Assigns an RCI address to an I O unit connected via RCI Before this command can be executed the RCI Host node settings must already have been made setrci c addconfig Makes the RCI settings for the case that a host unit or an V O unit is added C120 E361 04EN 1 3 CHAPTER 1 RCI Build Procedure 1 3 RCI Setup This section explains the RCI setup for the following cases e New setup for a single RCI Host and two RCI VO units e New setup of two RCI Hosts e When an RCI VO unit is added later When a RCI Host is added later Remarks Please refer to Appendix A Troubleshooting when there is a problem at RCI setup 1 3 1 New setup for a single RCI Host and two RCI I O units RCI Host TE u AA RCI I O unit RCI VO unit Figure 1 5 New setup for a single RCI Host and two RCI I O units l Log in to the XSCF Shell 2 Execute the setrci c stat command to display the RCI status XSCF gt setrci c stat HOST address OOOf7fff
21. with two RCIs VO units include units equipped with one RCI and units equipped with two RCIs The following figures show different RCI connection patterns RCI Hosts RCI 1 gt SL dl RCI RCI I O unit RCI I O unit Figure 1 1 Basic configuration C120 E361 04EN 1 1 CHAPTER 1 RCI Build Procedure RCI Hosts RCI Hosts RCI f RCI LU _ _ _ Li RCI I O unit RCI I O unit Figure 1 2 Cluster configuration RCI Hosts RCI Hosts RCI I O unit RCI I O unit Figure 1 3 Duplicated configuration RCI Hosts RCI Hosts c m RCI 1 O RCI O RCI I O unit RCI I O unit Figure 1 4 Mixture of duplicated and unduplicated configurations 1 2 C120 E361 04EN 1 2 RCI command 1 2 RCI command RCI commands are used to display RCI configuration information and set node addresses To connect I O units equipped with RCI ports a setup using RCI commands is required in addition to the connection with RCI cables Remarks When you use the terminal function of the External power controller perform the setrcic command and confirm setting or connection of the External power controller For details of the setrcic command see the RCI User s Guide or man page 1 2 1 Command list The RCI commands are explained below Table 1 1 Command list Command Function setrci c stat Displays RCI configuration information This command is used after the RCI setup to verify that the settings of the host and I O units ha
Download Pdf Manuals
Related Search