Frigidaire FRA144HT2 Air Conditioner User Manual
Contents
1. energy saver energy saver fan only PRESS FAN fan only BUTTON SELECT AUTO Note Fan starts at High Speed and adjusts to a slower speed as the room temperature dictates For example if the room doesn t get too warm it will stay at the slowest speed If the room temperature rises quickly such as a door being opened it will auto matically go to the highest speed The fan speeds will re adjust back to the slowest speed as the room returns to the original set temperature Press either the fan slower or fan faster button to adjust the fan speed manually This function is deactivated in the heating mode on 115V models TO OPERATE ON FAN ONLY YOU WILL SEE temp timer temp timer auto DO THIS nhi l lo na PRESS ies n col MODE BUTTON cel ae energy saver energy saver m fan only CHOOSE FAN ONLY Note Use this function only when cooling is not desired such as for room air circulation or to exhaust stale air on some models Remember to open the vent during this function but keep it closed during cooling for maximum cooling efficiency You can choose any fan speed you prefer Except Auto Fan During this function the display will show the actual room temperature not the set temperature as in the cooling mode Fan Only cannot be selected when the unit is in the Remote Sensing mode on those units with that feature 6 2009 Electrolux Home Products Inc All rights reserved Operating Instructions O2. Grounding Prong Do not under any circumstances cut remove or bypass the grounding prong amp SAFETY PRECAUTIONS WARNING For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Read product labels for flammability and other warnings WARNING Prevent Accidents To reduce the risk of fire electrical shock or injury to persons when using your air conditioner follow basic precautions including the following Be sure the electrical service is adequate for the model you have chosen This information can be found on the serial plate which is located on the side of the cabinet and behind the grille If the air conditioner is to be installed in a window you will probably want to clean both sides of the glass first If the window is a triple track type with a screen panel included remove the screen completely before installation Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual Save this manual and the installation instructions for possible future use in removing or reinstalling this unit When handling the air conditioner be careful to avoid cuts from sharp metal fins on front and rear coils WARNING Electrical Information The complete electrical rating of your new room air conditioner is stated on the serial plate Refer to th
3. cooling but room is too warm ice forming on cooling coil behind decorative front Air filter may be dirty Clean filter Refer to Care and Cleaning section To defrost set to FAN ONLY mode Temperature is set too low for night time cooling To defrost the coil set to FAN ONLY mode Then set temperature to a higher setting Dirty air filter air restricted Clean air filter Refer to Care and Cleaning section Air conditioner cooling but room is too warm NO ice forming on cooling coil behind decorative front Air conditioner turns on and off Temperature is set too high Set temperature to a lower setting Air directional louvers positioned improperly Position louvers for better air distribution Front of unit is blocked by drapes blinds furniture etc restricts air distribution Clear blockage in front of unit Doors windows registers etc open cool air escapes Close doors windows registers etc Unit recently turned on in hot room Allow additional time to remove stored heat from walls ceiling floor and furniture Dirty air filter air restricted Clean air filter rapidly Outside temperature extremely hot Set FAN speed to a faster setting to bring air through cooling coils more frequently Air movement sound This is normal If too loud set to lower FAN setting Noise when unit is cooling Sound of fan hitting water moisture removal system This is norma
4. front may be dusted with an oil free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent Rinse thoroughly and wipe dry Never use harsh cleaners wax or polish on the cabinet front Be sure to wring excess water from the cloth before wiping around the controls Excess water in or around the controls may cause damage to the air conditioner Plug in air conditioner Winter Storage If you plan to store the air conditioner during the winter remove it carefully from the window according to the installation instructions Cover it with plastic or return it to the original carton NOTE To prevent rust or electrical connections from being damaged store air conditioner in an upright position and a dry place Energy Saving Ideas Do not block air flow inside with blinds curtains or furniture or outside with shrubs enclosures or other buildings The capacity of the room air conditioner must fit the room size for efficient and satisfactory operation Install the room air conditioner on the shady side of your home A window that faces north is best because it is shaded most of the day Close the fireplace damper floor and wall registers so cool air does not escape up the chimney and into the duct work Keep blinds and drapes in other windows closed during the sunniest part of the day Clean the air filter as recommended in the section Care and Cleaning Proper insulation and weat
5. 55 Terry Fox Way P O Box 212378 Mississauga Ontario Canada Augusta GA 30907 L5V 3E4 1 2 2009 Electrolux Home Products Inc All rights reserved
6. FRIGIDAIRE Use amp Care Important Safety Instructions 00 Product Reg SaO enters Normal Sounds cscse ete Air Conditioner Features cccsscsseseees Operating SOn eee www frigidaire com USA 1 800 944 9044 TABLE OF CONTENTS sais tenons 23 Care and Cleaning s ss 0 ss sseaseneeeameeea eaten T RRT 4 Energy Saving deas e T aT 4 Before You Call a T T 5 Major Appliance Limited Warranty ccccssseeees Pa 5 10 www frigidaire ca Canada 1 800 265 8352 6002 unf 9SOTVETZOZOZ Important Safety Instructions amp note This USE amp CARE MANUAL provides specific operating instructions for your model Use the room air conditioner only as instructed in this USE amp CARE MANUAL These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance amp note The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire Please refer to the section Operation of Current Device for details In the event that the power supply cord is damaged it cannot be repaired It must be replaced with a cord from the product manufacturer WARNING Avoid fire hazard or electric shock Do not use an extension cord or an adaptor plug Do not remove any prong from the power cord
7. L EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE QUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If You Need Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period Service should service be required If service is performed it is in your best interest to obtain and keep all receipts Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below This limited warranty only applies in the USA and Canada In the USA your appliance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as described or illustrated are subject to change without notice USA Canada 1 800 944 9044 1 800 265 8352 Electrolux Major Appliances Electrolux Canada Corp North America 2 Electrolux 58
8. NG BUTTON Operating Instructions amp note The following instructions represent the Touch Pad the same instructions can be used for the Remote Control TO TURN UNIT ON YOU WILL SEE temp timer auto A auto A H filt pul filt er er p DO THIS o B a PRESS ON OFF fan heat speed cool m cool energy saver remote BUTTON remote sensing energy saver sensing fan only fan only Vv el nw 8 2009 Electrolux Home Products Inc All rights reserved 5 fan heat speed Operating Instructions Operating Instructions TO CHANGE TEMPERATURE SETTING YOU WILL SEE temp timer temp timer auto A sti DO THIS z lo med med i fan heat PRESS A TO RAISE fan je speed m cool speed m cool energy saver energy saver fan only 7 PRESS v TO LOWER fan only Note Tap or hold either up A or down V button until the desired temperature is seen on the display This temperature will be automatically maintained anywhere between 60 F 16 C and 90 F 32 C for cooling mode The temperature will be auto matically maintained anywhere between 55 F 13 C and 80 F 27 C for heating mode If you want the display to read the actual room temperature See To Operate on Fan Only section on this page TO ADJUST FAN SPEEDS YOU WILL SEE temp timer temp timer o m heat DO THIS speed m cool energy saver energy saver fan only n onl y PRESS TO SELECT o l DO THIS
9. e rating when checking the electrical requirements Be sure the air conditioner is properly grounded To minimize shock and fire hazards proper grounding is important The power cord is equipped with a three prong grounding plug for protection against shock hazards e Your air conditioner must be used in a properly grounded wall receptacle If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker have a qualified electrician install the proper receptacle Do not run air conditioner without outside protective cover in place This could result in mechanical damage within the air conditioner Do not use an extension cord or an adapter plug DANGER Avoid Serious Injury or Death e This air conditioner contains no user serviceable parts Always call an authorized Electrolux servicer for repairs Do not insert or place fingers or objects into the air discharge area in the front of the unit Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box Do not cut or damage the power cord If the power cord is damaged it should only be replaced by an authorized Electrolux servicer e Inthe event of a malfunction sparks burning smell etc immediately stop the operation disconnect the power cord and call an authorized Electrolux servicer Do not operate the air conditioner with wet hands Do not
10. feature is a reminder to clean the Air Filter See Care and Cleaning for more efficient operation The LED light Will illuminate after 250 hours of operation To reset after cleaning the filter press the Filter Reset button and the light will go off REMOTE SENSING FEATURE on some models LIGHT pulsing On amp Off intermittently TEMP TIMER o i TEMP TIMER temp timer A filter qH reset XILSY4 NW4 i LNS FAN SLOWER FAN SLOWER waLSV4 NWS TEMP TIMER DO THIS remote sensing E Vv m NOTE Unit display shows the set temperature NOTE Remote display is actual temperature at remote control only PRESS REMOTE SENSING START BUTTON FRIGIDAIRE FRIGIDAIRE Note This feature can be activated from the remote control ONLY the unit must be in a cooling mode To activate the remote sensing feature point the remote control towards the unit and press the remote sensing Start button Next use the A V buttons to set the desired temperature at the remote Note that the set temperature will only be displayed on the unit itself The LIGHT on the unit control will pulse to indicate it received the signal The LIGHT on the remote control will pulse each time it sends a signal It will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button If the unit does not receive the remote sensing signal during any 3 minute
11. he same as previously set To change the set temperature press COOL then Up or Down arrows until the desired temperature is indicated on the display After 5 seconds the control will automatically change the display back to the hours remaining until the unit will start stop Pressing the unit On Off button at any time will cancel the Delay Start Stop function The Delay Start Stop Feature will work until the unit either starts or stops Once that happens the above steps have to be repeated again SLEEP FEATURE temp timer DO THIS PRESS one SLEEP BUTTON sensing timer YOU WILL SEE a timer a a remote sensing Note In this mode the selected temperature will increase by 2 F 30 minutes after the mode is selected The temperature will then increase by another 2 F after an additional 30 minutes This new temperature will be maintained for 7 hours before it returns to the originally selected temperature This ends the Sleep mode and the unit will continue to operate as originally programmed The Sleep mode program can be cancelled at any time during operation by again pressing the Sleep button 2009 Electrolux Home Products Inc All rights reserved 7 Operating Instructions Operating Instructions continued CHECK FILTER FEATURE YOU WILL SEE temp timer temp timer A iB filter 76 reset DO THIS remote PRESS FILTER scene RESET BUTTON remote sensing Vv e Note This
12. her stripping in your home will help keep warm air out and cool air in External house shading with trees plants or awnings will help reduce the air conditioner s work load Operate heat producing appliances such as ranges washers dryers and dishwashers during the coolest part of the day 1 0 2009 Electrolux Home Products Inc All rights reserved Before You Call Before calling for service review this list It may save you time and expense This list includes common occurrences that are not the result of defective workmanship or materials in this appliance OCCURRENCE SOLUTION Wall plug disconnected Push plug firmly into wall outlet Air conditioner will not operate Plug Current Device Tripped Press the RESET button House fuse blown or circuit breaker tripped Replace fuse with time delay type or reset circuit breaker Control is OFF Turn Control ON and set to desired setting Room temperature below 60 F 16 C Cooling may not occur until room temperature rises above Air from unit does not feel cold enough 60 F 16 C Temperature sensing element touching cold coil located behind air filter Straighten away from coil Reset to a lower temperature Compressor shut off by changing modes Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode Outdoor temperature below 60 F 16 C To defrost the coil set FAN ONLY mode Air conditioner
13. interval the unit will beep to indicate the remote sensing mode has ended The display on the remote control indicates the temperature at the remote ONLY NOTE The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON OFF button on the unit HEATING FEATURE on some models YOU WILL SEE temp timer temp timer auto A auto A DO THIS Bal med i TH fan heat fan m heat speed PRESS speed cool m cool energy saver MODE BUTTON energy saver v fan only SELECT HEAT timer Note This feature can be used with any combination of FAN Speeds Low speed only on 115V models Timer or Sleep Modes When in the Heat mode the fan will run continuously while heat is needed The temperature will automatically be maintained anywhere between 55 F 13 C and 80 F 27 C When the room set temperature is satisfied the fan will cycle off and on to circulate and sample the room air g 2009 Electrolux Home Products Inc All rights reserved Operating Instructions Operating Instructions continued FAULT CODES a timer auto auto Bhi mhi filter m ae ma a zn m heat en m heat cool cool remote energy saver sensing energy saver temp timer fe oa remote sensing If the display reads AS a sensor has failed Contact your Authorized Frigidaire Service Center TO CHANGE TEMPERATURE DISPLAY i only om only If the display reads HS a sensor has fai
14. l when humidity is high Close doors windows and registers Window vibration poor installation Refer to installation instructions or check with installer Improper installation Tilt air conditioner slightly to the outside to allow water drainage Refer to Water dripping INSIDE when unit is cooling Water dripping OUTSIDE when installation instructions or check with installer Unit removing large quantity of moisture from humid room This is normal during excessively humid unit is cooling days Remote control not located within range Place remote control within 20 feet amp 120 radius of the Remote Sensing Deactivating Prematurely some models Room too cold front of the unit Remote control signal obstructed Remove obstruction Set temperature too low Increase set temperature Remote Sensing activated on some models and remote control located in Hot Spot Relocate remote control or deactivate remote sensing If These Solutions Fail Call 1 800 944 9044 For Frigidaire Service 2009 Electrolux Home Products Inc All rights reserved 11 Major Appliance Limited Warranty Your appliance is covered by a limited two year warranty and a limited 3 5 year warranty on the sealed system the compressor condenser evaporator and tubing For two years from your original date of purchase Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defec
15. led Contact your Authorized Frigidaire Service Center temp timer a auto ahi ES er gm A A m heat A cool remote energy saver sensing fan only o i a sensor has If the display reads ES failed Contact your Authorized Frigidaire Service Center YOU WILL SEE temp timer DO THIS PRESS AND HOLD THE UP DOWN BUTTONS TOGETHER FOR 3 SECONDS Note The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius TO TURN UNIT OFF YOU WILL SEE ao ae ter ae remote sensing a fater lter fater remote sensing DO THIS PRESS ON OFF BUTTON time Note When unit is shut off in the Heat Mode the fan will continue to run for a few seconds to dissipate residual heat within the unit ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure here are more features in your control that you should become familiar with e The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly This prevents overheating of the compressor and possible circuit breaker tripping The fan will continue N to run during this time e There is a 2 Second delay for the compressor shutting down when selecting FAN ONLY HEAT This is to cover the possibility of having to roll through to select another mode e The control will maintain the set temperature within 2 degrees Fahrenheit between 60F and 90F degrees in c
16. ool mode 55F and 80F degrees in heat mode e After a power outage the unit will memorize the last setting and return the unit to the same setting once power is restored 2009 Electrolux Home Products Inc All rights reserved 9 Operating Instructions amp Care and Cleaning amp Energy Saving Ideas Operating Instructions continued 4 WAY 4 Way Air Directional Louvers The 4 Way air directional louvers allow you to direct the air flow Up or Down and Left or Right throughout the room as needed To adjust the air direc tional louvers side to side use the center handle as you move it side to side Care and Cleaning Clean your air conditioner occasionally to keep it looking new Be sure to unplug the unit before cleaning to prevent shock or fire hazards Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils e Grasp the filter by the center and pull up and out e Wash the filter using liquid dishwashing detergent and warm water Rinse filter thoroughly Gently shake excess water from the filter Be sure filter is thoroughly dry before replacing Or instead of washing you may vacuum the filter clean Cabinet Cleaning Be sure to unplug the air conditioner to prevent shock or fire hazard The cabinet and
17. perating Instructions continued TO USE THE ENERGY SAVER FEATURE temp timer auto A mo DO THIS med lo P a5 PRESS speed col MODE BUTTON energy saver v m fan only CHOOSE ENERGY SAVER YOU WILL SEE temp timer A i i speed cool m energy saver fan only Note In this mode the fan will continue to run for 1 minute after the compressor shuts off The fan then cycles on for 20 seconds at 10 minute intervals until the room temperature is above the set temperature at which time the compressor turns back on TIMER DELAY STOP START FEATURE temp timer FIRST THEN DO THIS PRESS TIMER BUTTON PRESS Note For Delay Stop the unit must be in the On position Note For Delay Start the unit must be in the Off position DO THIS UP DOWN SET BUTTONS YOU WILL SEE HOW MUCH TIME IS CHOSEN temp timer First Press TIMER button then adjust timer setting tap or hold the UP arrow A or the DOWN arrow V to change delay timer at 0 5 hour increments up to 10 hours then at 1 hour increments up to 24 hours The control will count down the time remaining until start 8 7 5 7 etc The Delay Start Operation automatically selects cooling with maximum Fan speed if Cool Energy Saver or Fan Only was the last mode selected or heating with maximum Fan speed if Heat was the last mode selected Note On 115V models only low speed can be selected The temperature maintained will be t
18. pull on the power cord Do not drink any water that is drained from the air conditioner 2 2009 Electrolux Home Products Inc All rights reserved Important Safety Instructions SAFETY PRECAUTIONS CAUTION Avoid Injury or damage to the unit or other property Provide occasional ventilation during use Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively Do not climb on or place objects on outdoor part of the unit Do not hang objects off the unit Do not place containers with liquids on the unit Turn off the air conditioner at the power source when it will not be used for an extended period of time e Periodically check the condition of the unit s installation accessories for any damage Do not apply heavy pressure to the radiator fins of the unit e Operate the unit with air filter in place Do not block or cover the intake grille discharge area and outlet ports Ensure that any electrical electronic equipment is one yard away from the unit Do not use or store flammable gases near the unit READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER Unit must be upright for one hour prior to operating The power supply cord contains a current device that senses damage to the power cord To test Operation of Current your power supply cord do the following Device 1 Plug in the Air Conditioner 2 The power
19. supply cord will have TWO buttons on the plug head Press the TEST button You will notice a click as the RESET button pops out 3 Press the RESET button Again you will notice a click as the button engages 4 The power supply cord is now supplying electricity to the unit NOTE Do not use this device to turn the unit on or off Always make sure the RESET button is pushed in for correct operation The power supply cord must be replaced if it fails to reset when either the TEST button is pushed or it cannot be reset A new one can be obtained from the product manufacturer If power supply cord is damaged it CANNOT be repaired It MUST be replaced by one obtained from the product manufacturer Plug in amp press RESET 2009 Electrolux Home Products Inc All rights reserved 3 Product Registration amp Normal Sounds Product Registration Record Your Model and Serial Numbers Record in the space provided below the model and serial numbers On all models the serial plate is located on the outside of the cabinet Model No Serial No Register Your Product The self addressed PRODUCT REGISTRATION CARD should be filled in completely signed and returned to the Frigidaire Company Normal Sounds High pitched Chatter Today s high efficiency compressors may have a high pitched chatter Vibration during the cooling cycle Unit may vibrate and make noise because of poor wall or window construc
20. tion or incorrect installation Sound of Rushing Air At the front of the unit you may hear the sound of rushing air being moved by the fan Pinging or Swishing Droplets of water hitting condenser during normal operation may cause pinging or swishing sounds Gurgle Hiss Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation 2009 Electrolux Home Products Inc All rights reserved Air Conditioner Features amp Operating Instructions Air Conditioner Features ELECTRONIC CONTROL Before you begin thoroughly familiarize yourself with the control panel and remote as shown below and all its functions then follow the symbol for the functions you desire The unit can be controlled by the touch pad alone or with the remote ADJUSTS TEMPERATURE DISPLAYS OR TIME TEMPERATURE TIME SLEEP MODE temp timer auto A ls filter CHECK FILTER lo fe reset RESET BUTTON SETS FAN SPEED heat REMOTE TEMP cool emote SENSING INDICATOR energy saver sensing some models fan only SETS MODE TURNS UNIT ON OR OFF ACTIVATES TIMER TEMP TIMER ZV S TEMP TIMER Battery Size AAA remote senstog Warning Do not mix old and new batteries Do not mix alkaline standard FRIGIDAIRE ERIGIDAIBE carbon zinc or rechargeable nickel cadmium batteries w DISPLAY amp FOR HEAT MODELS REMOTE SENSI
21. tive in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions From the third to the fifth year from your original purchase date Electrolux will repair or replace any parts in the Sealed Refrigeration System compressor condenser evaporator and tubing that prove to be defective in materials or workmanship In years 3 5 the consumer will be responsible for diagnostic labor and parts costs as well as any removal transportation and reinstallation expenses which are incurred during service on components other than those covered under the Sealed Refrigeration System 5 year warranty Exclusions This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada 3 Rust on the interior or exterior of the unit 4 Products purchased as is are not covered by this warranty 5 Food loss due to any refrigerator or freezer failures 6 Products used in a commercial setting 7 Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in ordinary household use or used other than in accordance with the provided instructions Service calls to correct the installation of your appliance or to instruct you how to use your appliance 8 9 E
22. xpenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory 10 Service calls to repair or replace appliance light bulbs air filters water filters other consumables or knobs handles or other cosmetic parts 11 Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska 12 Damages to the finish of appliance or home incurred during installation including but not limited to floors cabinets walls etc 13 Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes such as abuse misuse inadequate power supply accidents fires or acts of God DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTA
Download Pdf Manuals
Related Search