Frigidaire 242062402 Refrigerator User Manual
Contents
1. moving refrigerator out for cleaning E DRAE water line L NOTE Js Water Valve Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator Depending on your local state building codes Frigidaire recommends for homes with existing valves its Smart Choice water line kit 5305513409 with a 6 ft Stainless Steel Water Line and for homes without an existing valve Frigidaire recommends its Smart Choice water line kit 5305510264 with a 20 ft Copper Water Line with self tapping saddle valve Please refer Fi 2 to www frigidaire com for more information igure 6 ft Stainless Steel water line from household water supply Level Refrigerator Guidelines for final positioning of your refrigerator e All four corners of the cabinet must rest firmly on the floor e The sides should tilt inch 6 mm from front to back to ensure that doors close and seal properly e Doors should align with each other and be level Most of these conditions can be met by raising or lowering the adjustable front rollers To level the cabinet using the front rollers 1 You can raise or lower each door Use a 3 s inch socket wrench to turn the adjustment screws 1 per side To raise turn adjustment screw clockwise To lower turn adjustment screw counterclockwise Ensure both doors are bind free with their seals touching the cabinet on all four sides and2. on Refrigerator plugged in House water supply connected to P N 242062402
3. that cabinet is stable After unit is leveled lower anti tip leg until it contacts the floor DO NOT REMOVE this label until the refrigerator has been leveled Please follow all instructions for leveling your refrigerator 4 Installing amp Leveling Freezer Drawer if necessary 1 Installing freezer drawer Refer to Installing Freezer Drawer in the Use amp Care Guide 2 Leveling freezer drawer Remove Hex Remove Hex Head Drawer Head Drawer Screw Screw Check gasket seal around top bottom De Nox Remar Do Net Roms and sides of freezer drawer a pe If gasket is not sealed open drawer and slightly loosen 4 drawer screws S Z 2 on each side to allow drawer to Remove Hex PIN ant Remove Hex rotate Screw i x ij aaron Close drawer and recheck the seal on the gasket A Open the drawer grabbing by the sides in the center B Be careful not to rotate the EEA drawer At Center Tighten 4 drawer screws From Bothi Sidas Push Against Then Recheck gasket seal Freezer Drawer Pull Drawer Out Install the toe grille by fitting gt into place A A 5 Installing amp Adjusting Doors if necessary 1 Installing doors Refer to Installing Doors in the Use amp Care Guide 2 Doors final adjustment using the adjustable lower hinge select models if necessary Open Doo
4. FRIGIDAIRE Installation Instructions for French Door Bottom Freezer Refrigerator Please refer to your Use amp Care Guide for more details WARNING To avoid electric shock which can cause death or severe personal injury do not connect your refrigerator to an electrical power source until you have completed Step 2 of these instructions amp NOTE If you need to remove the doors to get your refrigerator into the house please refer to Removing Doors in the Use amp Care Guide These installation instructions are provided onl as a possible customer Option Frigidaire recommends that you use a service or kitchen contracting professional to install your refrigerator mA IMPORTANT CAUTION ped eng your refri erator e Shifting the refrigerator from side to side supply make sure the ice maker s may damage flooring _ poner switch is turned Off see the e Do not block the toe grille on the lower se amp Care Guide for more details front of your refrigerator Sufficient air cir culation is essential for proper operation l Preparing For Installation Be sure to coordinate site preparation and installation with your kitchen contractor Include these minimum guidelines in your site preparation 4 NOTE Choose a place near a grounded electrical outlet Do not use an extension cord or an adapter plug Avoid direct sunlight and close proximity to a range Please call 1 800 944 9044 if you dishwasher or other heat source ne
5. ed assistance with this installation Floor should be level and able to support a fully loaded refrigerator The refrigerator s Ice Dispenser requires water supply access Plan for easy access to counter tops when removing food d d r complete access to drawers an l f freezer baskets doors must be able to V below 55 F 1 Heats j i si 43 C will impair fore refrigerator from side of cabinet cooling ability of x your refrigerator s compressor CAUTION Do not run retaining straps over handles nor overtighten straps Never use refrigerator handles to move the refrigerator Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides amp Top 3 s inch Rear 1 inch 2 Connect Water Supply Before Installing The Water Supply Line You Will Need e Basic Tools adjustable wrench flat blade screwdriver and Phillips screwdriver WARNING Heese ina Oe cold water line with water pressure tween 30 an psi e A water supply line made of 1 4 inch 6 mm OD copper To avoid electric shock or stainless steel tubing To determine the length o or severe personal tubing needed measure the distance from the ice injur aiecannces the maker inlet valve at the back of the refrigerator to your ekrid arator from elec cold water pipe Then add approximately 7 feet so the trical power before con retigerator can oe moreg ou for ceaning inet necting a water sup
6. ession and discard cap Nut If you use copper tubing Slide brass compression nut then ferrule sleeve onto sleeve water supply line Push water supply line into i water valve inlet as far as it will go 1 4 inch 4 hee Slide ferrule sleeve into valve inlet and Water lihe finger tighten compression nut onto valve XW Tighten another half turn with a wrench DO 7 Water Valve NOT overtighten See Figure 1 i Bracket If you use stainless steel tubing The nut b verais and ferrule are already assembled on the tubing Slide compression nut onto valve z Water Valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure 2 With steel clamp and screw secure water supply line copper tubing only to rear panel of refrigerator as shown Coil excess water supply line copper tubing only about 21 2 turns behind refrigerator Figure 1 as shown and arrange coils so they do not vibrate or wear against any other surface Turn ON water supply at shutoff valve and tighten any connections that leak Plastic Water Reconnect refrigerator to electrical power Mobing source To turn ice maker on lower wire signal arm freezer ice maker or set the ice maker s On Off power switch to the ON position fresh S food ice maker A f Stainless Steel Copper water line from household water supply Include enough tubing in loop to allow
7. ply shutoff valve to connect the water su ine to your i A Utell water system DO NOT use P eele piercing type line to the refrigerator shutoff valve A compression nut and ferrule sleeve for connecting a copper water supply line to the ice maker inlet valve CAUTION To Avoid Property Damage e Copper or Stainless Steel braided tubing is recommended for the wa ter supply line Water supply tubing made of 1 4 inch 6 mm plastic is not recommended to be used Plastic tubing greatly increases the potential for water leaks and the manufacturer will not be respon sible for any damage if plastic tubing is used for the supply line e Do not reuse compression fitting or use thread seal tape e DO NOT install water supply tubing in areas where temperatures fall below freezing e Chemicals from a malfunctioning softener can damage the ice maker If the ice maker is connected to soft water ensure that the softener is maintained and working properly If you are not satisfied with the installation of your refrigerator please contact the store where you purchased it or call 1 800 944 9044 for assistance To Connect Water Supply Line To Ice Maker Inlet Valve Disconnect refrigerator from electric power source Place end of water supply line into sink or bucket Turn ON water supply and flush ea supply line until water is clear Turn OFF ye Gas water supply at shutoff valve t Brass Remove plastic cap from water valve inlet Compr
8. r A Open doors to 90 degrees 90 B Lift the door while adjusting ee the washer To raise the door rotate Bottom of Door washer clockwise Opening Door Raising Lowering Door To lower the door rotate washer counterclockwise 6 Remove Internal Shipping Materials Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for shipping Once the refrigerator is in position you can remove this material What s Next Congratulations You are ready to begin enjoying your new Frigidaire refrigerator For important safety instructions and to learn how to operate your refrigerator please read the entire Use amp Care Guide You may want to start with the Normal Operating Sights amp Sounds section of the Guide to learn what to expect during typical operation Please register your product You can register online at www frigidaire com or you can simply send in the Registration Card 2 M Installation Check List Doors Ice Maker Handles are secure and tight Door seals completely to cabinet on all sides refrigerator Fresh food doors are level No water leaks present at all connections Leveling Ice Maker is turned ON Refrigerator is level side to side and tilted Final Checks Ya inch 6 mm front to back a Toe grille is properly attached to refrigerator Shipping material removed Cabinet is sitting solid on all corners Fresh Food and Freezer temperatures set Electrical Power House power turned
Download Pdf Manuals
Related Search