Home

Elation Professional 700 II Security Camera User Manual

1. 4 Loosen the two locking thumbscrews on the left and right side of the optical effects module please do not attempt to remove the thumbscrews completely Once the thumbscrews have been loosened push them inwards towards the center of the head while gently pulling the effects module straight out You may use the metal support plates to grasp and pull the effects module out See the illustration below Attention The effects module reset between two lateral tracks A moderate effort is normal when attempting to remove the unit Never use any of the sensitive wheel components like the gobo and color wheels or any cables to remove the module Use the metal support plates or the stepper motors as a Elation Professionals Los Angeles Ca wwww ElationLighting com Page 52 Power Spot 700 IIT means to grasp the module 5 To access the internal components of the module loosen the three securing thumbscrews illustrated below Once these screws are lose you may place the module on a flat and open the unit up as if it were a book This will allow access the all the gobos and colors so they may be changed or cleaned 6 For Gobo and Color replacement please see the next section 7 To replace module a Fold up the module and fasten the three retaining thumbscrews Elation Professionals Los Angeles Ca wwww ElationLighting com Page 53 Power Spot 7
2. Channel Function Time and Value DMX HEX new gobo 10 Gobo 2 Gobo Position 0 540 0 127 00 7F 0 49 Posi Rot Gobo Rotation STOP 128 129 80 81 50 Gobo Rotation Slow fast CW Min 2 0 turns h 130 191 82 BF 51 75 Gobo Rotation Fast slow CCW Max 3 8 turns sec 192 253 CO FD 76 100 Audio Gobo Rotation Slow Each 4 sound impulse 254 FE 99 gt new position Audio Gobo Rotation Fast Each sound impulse gt 255 FF 100 new gobo 11 Gobo 3 Gobo 1 open fast Chaser from gobo to 0 3 00 03 0 1 fast Gobo 2 fast er 4 7 04 07 2 3 Gobo 3 fast SES 8 11 08 08 3 4 Gobo 4 fast 12 15 OC 0F 5 6 Gobo 5 fast 16 19 10 13 6 7 Gobo 6 fast 20 23 14 17 8 9 Gobo 7 fast 24 27 18 1B 9 10 Gobo 8 fast 28 31 1C 1F 11 12 Gobo 9 fast 32 35 20 23 13 14 Gobo 10 fast 36 39 24 27 14 15 Gobo 1 open slow Chaser from gobo to 64 67 41 43 25 26 Gobo 2 slow Genoa BEN 68 71 44 47 27 28 Gobo 3 slow RE 72 75 48 4B 28 29 Gobo 4 slow 76 79 4C 50 30 31 Gobo 5 slow 80 83 51 53 32 33 Gobo 6 slow 84 87 54 57 33 34 Gobo 7 slow 88 91 58 5B 35 36 Gobo 8 slow 92 95 5C 5F 36 37 Gobo 9 slow 96 99 60 63 38 39 Gobo 10 slow 100 103 64 67 39 40 Gobo rotation STOP 128 129 80 81 50 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 42 Power
3. sound impulse 176 191 BO BF 69 74 gt new position Audio Pan Tilt fast Each sound impulse gt 192 207 CO CF 75 81 new position No function 208 223 DO DF 82 87 Fan min as long as temp lt 90 C 224 229 E0 E5 88 90 Lamp OFF min 3 sec if Shutter 230 249 E6 F9 92 97 closed 000 Reset 250 255 FA FF 98 100 20 Move No movement 0 00 0 ment Movement Size Phase PAN 1 0 01 01 01 01 0 5 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 44 Power Spot 700 IIT Channel Function Time and Value DMX HEX 1 90 02 03 02 03 1 0 1 180 04 05 04 05 1 7 1 270 06 07 06 07 2 5 PAN 2 0 08 09 08 09 3 3 2 90 10 11 0A 0B 4 1 2 180 12 13 OC 0D 4 9 2 270 14 15 OE 0F 5 7 PAN 3 0 16 17 11 11 6 5 3 90 18 19 12 13 7 3 3 180 20 21 14 15 8 0 3 270 22 23 16 17 8 8 PAN 4 0 24 25 18 19 9 6 4 90 26 27 1A 1B 10 4 4 180 28 29 1C 1D 11 2 4 270 30 31 1E 1F 12 TILT Size phase see also PAN 32 63 20 3F 13 25 PAN TILT Size phase see also PAN 64 95 40 5F 26 37 PAN TILT inverse Size phase see also PAN 96 127 60 7F 38 50 Circle Size phase see also PAN 128 159 80 9F 51 62 Circle inverse Size phase see also PAN 160 191 AO
4. Beam diameter 0 24 x distance Field angle 13 40 Color temperature 7500 Kelvin no color filters applied Measurement conditions 230V 50Hz Measurement source Osram HTI 700W D4 75 Field diameter minimum spread Luminous intensity candela e ECEL EE D 2 3 4 5 6 7 B 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Distance m or tt Power Spot 700 Photometric Data Illuminance lux or fc 122250 cd distance lt m or ft Beam diameter 0 62 x distance Field angle 34 60 Color temperature 7500 Kelvin no color filters applied Measurement conditions 230V 50Hz Measurement source Osram HTI 700W D4 75 All informationis subject to change without prior notice liluminance minimum spread 20 40 60 80 100 120 140 160 80 MO 220 240 Distance m or fi Muminanse lux or fe Luminous intensity distribution minimum spread 70 60 50 40 30 20 10 00 10 20 30 40 50 60 70 Degrees from center Illuminance maximum spread e S illuminance lux or fc o 20 40 60 80 100 12 0 14 0 16 0 180 20 0 22 0 240 Distance m or ft Field diameter maximum spread Field diameter m or ft oN a o o 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Distance m or ft Luminous intensity distribution maximum spread 140000 120000 100000 80000 60000 40000 Luminous intensity candela 20000 o 16 14 12 10 8 6 4 2
5. ELATION POWER SPOT 700 I User Manual Revised 5 14 08 visage Power Spot 700 IIT Elation Professionals Los Angeles Ca wwww ElationLighting com Page 2 Features NO PF WON Table of Contents Introduction eee eee aaa aaa aaa aaa aa Up re ei 4 n o EE Customer Support E Discharge Lamp Precautions EEN SEENEN Safety Instructions i i aa aaa Gas General Guidelines a a Fixt re LAY OU coca eege EE Mounting and Installation eee e etree eee eee eteeeeaaaaaaaaaaaeeeees Understanding DMX 25 pecan eee Diet dei ec ta de tt Dale i a da bn cae a TAS DMX 5 12002 co aaa oala Teale cul ae ala i otet ioni weds pc aed T2 MER To DMX Cables enle ne aes Saath m a Denes tyke taeda a data TA DMX Termilnati ll EE ENER OK e EE Fixture M n eege Seed doo Cu zf a d a a O la i 8 1 Setting the DMX Address UDO071 a r arssssssssssssa 8 2 Test Program TEST dei ear aes i i aa dal a aa a eS 8 3 Audio PROGKANM iio sie eee ie ed alta la le iu dit lac ba eta 8 3 Lamp On Off EAMP uuu uuu cited cate i d alia a tin a ia cl le 8 5 Reset EE 8 6 Running Time lamp unit TIME nanaaaanononnee ceai 8 7 Invert Pan Movement RAN coco ocean e aaa i 8 8 Invert Tilt Movement RULT 3 a coc o te cate o a a n skeet 8 9 Special
6. Power Spot 700 IIT 8 4 Lamp On Off LAMP This function allows you to manually control the lamp operation Access the lamp function in the main menu and use the use the Up and Down buttons to toggle between lamp On and lamp Off Press the Enter button to confirm the operation or the Mode button to cancel and return to the main menu The lamp OFF command will only functions if and when the shutter is closed at the same time 8 5 Reset RESE This function will rest and return all motors to the home position Access the reset function in the main menu and press the Enter button to engage the reset function RST will readout in the display 8 6 Running Time lamp unit TIME This menu function will read out three different fixture running times POWR Fixture running time non destructible Total running time logged by the unit LA I Lamp running time erasable Press and hold down the Up and Down buttons together for three seconds to reset this function LA d Lamp running time non destructible Total lamp hours logged by the unit 8 7 Invert Pan Movement RPA This function allows you to invert all pan movements Use the Up and Down buttons to turn this function On and Off Press the Enter button to accept the change or the Elation Professionals Los Angeles Ca wwww ElationLighting com Page 26 Power Spot 700 I
7. The fixture will wait approximately 2 minutes and attempt the lamp ignition process once again After the 3rd unsuccessful ignition attempt the sequence is completely stopped and the display reads IG E Ignition error LAER After the ignition of the lamp was two times not successful the display will show LAER That means the lamp could be damaged or even missed the fixture is overheating or there could be a failure on the igniter or ballast Switch off the power supply and solve the possible problem After the error lb E respectively LAER it is not anymore possible the start the lamp via Shutter 255 Nevertheless if a renewed ignition attempt is desired first run a Reset at the Spot or over DMX Afterwards you can try again to ignite the lamp OTMP This error message informs you that the fixture was overheating and lamp has electronically been switched off to allow the fixture to cool to normal operating temperatures Please look for any possible reason that may have caused the fixture to overheat i e faulty fans air vents blocked or dirty lamp broken or very old too high ambient temperature Switch off the power supply and solve the possible problem RSER This message informs you that one of the fixture function wasn t able to do its reset correct magnetic sensor stepping motor driver on the PCB cables etc Repair the defect and start the fixture again MDE The Power Spot 700 has an au
8. description of the DMX traits To control your fixture in DMX mode follow the set up procedures beginning on page 19 of this manual as well as the set up specifications that are included with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs 9 1 1 Follow the instruction on page 24 to set the DMX address 9 1 2 Be sure to use a terminator on the last fixture 9 1 3 For help operating in DMX mode consult the manual included with your DMX controller 9 2 Stand Alone Operation Sound Active This mode allows a single fixture to run to the beat of the music Only use this mode when running a single fixture or when running several fixtures as individuals 9 2 1 Mount your fixture in a secure and stable manner Elation Professionals Los Angeles Ca wwww ElationLighting com Page 34 Power Spot 700 IIT 9 2 2 9 2 3 9 2 4 9 2 5 9 2 6 Access the main menu and select the AUDI function this will give you access to the audio submenu See page 25 for the menu breakdown In the audio submenu choose the audio chase speed fast or slow Slow ASLW will trigger the chase sequence to every two beats while fast AFST will trigger the chase impulse every beat See page 25 for more details Be sure the Master MSTR function is switched ON and the SVPT function is switched OFF Choose your room size The size function
9. 0 2 4 6 8 10 12 14 16 Degrees from center Elation Professionals Los Angeles Ca wwww ElationLighting com Page 63 Power Spot 700 IIT 18 DIMENSIONS 326 0 464 5 641 2 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 64 Power Spot 700 IIT 19 TECHNICAL SPECIFICATION Power supply Power consumption 90 260V 50 60 Hz 1000 Watt 4 5 A electronic ballast blind current compensated Fuse protection Lamp 120v GMA 10A 250V 5x20 mm fine wire fuse Electronic 120v GMA 2A 250V 5x20 mm fine wire fuse Lamp 220v GMA 5A 250V 5x20 mm fine wire fuse Electronic 220v GMA 1A 250V 5x20 mm fine wire fuse Lamp Type MSR700 SA DE Philips Gold Live time 750hrs Color temperature 7500kK Luminous flux 56 000Im Optical system Dichroic coated glass reflector Beam angel variable 14 32 Lenses hardened and tempered anti reflex coated Colors 16 Bit Color wheel 1 8 dichroic filters plus white 9 half colors Color wheel 2 8 dichroic filters plus white 9 half colors 1x CTC 5500 1x CTC 3200 Gobos 16 Bit Gobo wheel 1 7 exchangeable rotating gobos plus open Gobo wheel 2 7 exchangeable rotating gobos plus open Gobo whee
10. Button This button is used to scroll forward when navigating through the system menu Elation Professionals Los Angeles Ca wwww ElationLighting com Page 15 Power Spot 700 IIT 6 MOUNTING AND INSTALLATION Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were unauthorized personnel might reach the fixture Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Mounting The POWER SPOT 700 II is fully operational in two different mounting positions hanging upside or set on a flat level surface To avoid internal damage to the unit never mount the unit on its side as illustrated below Be sure this fixture is kept at least 1 5 feet away from any flammable materials decoration etc Install a safety cable that can hold at least 10 times the weight of the fixture Never use the carrying handles for secondary attachment an aaa 44a ai qi l 4 yy AD ea k C NL NL NL AM LL LL ga ZY Elation Professionals Los Angeles Ca wwww ElationLighting com Page 16 Power Spot 700 IIT Refer to regulations BGV C1 formerly VBG 70 and DIN VDE 0711 217 for proper installation in Europe To ensure proper installation only qua
11. Fan air inlet outlet 18 Main Power Supply Powercon 19 Electronics Fuse Elation Professionals Los Angeles Ca wwww ElationLighting com Page 12 Power Spot 700 IIT Side View Menu and Display 20 4 Segment LED Menu Display 21 Mode Button 22 Enter Button nan No HUT Z 2 23 Up Button 24 Down Button 6 20 21 22 23 24 DA ANOO AAC DOD GAS ASAS SES LS LS LS LN LS DED 10 J Jr NIN NI NINI INI La Kai VU VZ KZ KZ Head Assembly The head assembly consist of the main output lens and either the standard or CMY control module Carrying Handle The fixtures includes two built in carrying handles Be sure to always handle the fixture by the built in carrying handles Never lift or carry the fixture by the head or retaining arms as this could cause serious damage to the fixture and void your manufactures warranty 4 Segment Menu Display This display details all the various menu functions See page 23 for a detailed breakdown of the operating menu Tilt Lock This lock will hold the head assembly in place for transportation and or service Depress the lock button to lock and unlock the head assembly The head will lock in a 90 or 45 orientation Always be sure to unlock the head assembly before applying main power to the unit Failure to do so will result in a start up error and may damage the unit Omega Clamp This fixture uses a cam lock clamp s
12. Powercon Connected load 1000W lt gt 4 5 A blind current compensation NOTE The universal power supply will accept any voltage source as detailed above without any type of internal or user modifications DMX USITT DMX 512 Standard input output 3 pole connectors Pin 3 Pin 2 Ground Pin 1 Fuse Requirements The POWER SPOT 700 Il s electronic and lamp systems are protected by two GMA 5x20mm external fuses Lamp 250v 10A 120v Operation or 250v 5A 220v Operation Electronics 250v 2A 120v Operation or 250v 1A 220v Operation The fuse requirements are clearly printed on the side of the fixture Always disconnect main power before changing the fuse Always replace with the exact same type fuse unless otherwise specified by an authorized Elation service technician Replacing with anything other than the specified fuse can severely damage your fixture and will void your manufactures warranty Elation Professionals Los Angeles Ca wwww ElationLighting com Page 11 Power Spot 700 Ii 5 FIXTURE LAYOUT 10 Build In Microphone NOOR ON Moving Head Carrying Handles LED Menu Display Head Tilt Lock Omega Clamp Ethernet Jack 5 Pin DMX Out Connector 5 Pin DMX In connector Microphone Sensitivity 11 Software Update Connector 12 3 Pin DMX Out Connector 13 3 Pin DMX In Connector 14 Carrying Handle 15 Power On Off 16 Lamp Fuse 17
13. Spot 700 IIT Channel Function Time and Value DMX HEX Gobo rotation slow fast CW Min 1 4 turns h 130 191 82 BF 51 75 Gobo rotation fast slow CCW Max 1 0 turns sec 192 253 CO FD 76 98 Audio gobo chase slow Each 4 sound impulse 254 FE 99 gt new gobo Audio gobo chase fast Each sound impulse gt 255 FF 100 new gobo 12 Shutter Shutter closed 0 15 00 0F 0 6 Random Strobe different pattern 16 31 10 1F 7 11 9 Strobe Pulse effect slow fast Min frequency 0 7 Hz 32 47 20 2F 12 12 9 Audio Shutter 48 63 30 3F 13 25 Strobe effect slow fast Max frequency 10 Hz 64 239 40 EF 26 93 Shutter open lamp start 240 255 FO FF 94 100 13 Dimmer Dimmer closed 0 0 3 0 3 0 1 Dimmer 1 99 Movement time 0 3 sec 4 251 4 FB 2 98 Dimmer open 100 252 255 FC FF 99 100 14 Focus In near out far Full distance 1 5 sec 0 255 0 FF 0 100 15 Zoom Inside near outside far Full distance 1 5 sec 0 255 0 FF 0 100 16 Frost Open 0 retracted 100 Full distance 1 5 sec 0 255 0 FF 0 100 17 Prism Prism swing out 0 5 00 05 0 2 Prism position 0 540 6 129 06 7F 0 50 Prism rotation stop 130 191 80 BF 51 75 Prism rotation slow fast CW Min 1 6 turns h 192 253 CO FD 76 100 Prism rotation fast slow CCW Max 4 4 turns sec 254 FE 99 Audio prism rota
14. b Be sure to always use two cam locks mounted to the bottom of unit to ensure safe truss mounting each two opposite threads max M10x20 00000 O Cam Lock fasteners position scheme Secure the POWER SPOT 700 II Regardless of the rigging option you choose for your POWER SPOT 700 II always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the underside of the fixture be sure to use this point and never secure a safety cable to a carrying handle Elation Professionals Los Angeles Ca wwww ElationLighting com Page 18 Power Spot 700 IIT 7 UNDERSTANDING DMX DMX 512 DMX is short for Digital Multiplex This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactures to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and data OUT XLR
15. button to activate that field and use the UP and Down button to adjust the field Tapping the Enter button once more will confirm your setting Once a setting is saved the LED will briefly readout OK to confirm a new setting has been made and locked into memory You may exit the main menu at any time without making any adjustments by tapping the MODE button MODE ENTER DOWN UP MODE ENTER DOWN UP LEVEL LEVEL LEVEL Remark l d 3 100 Define the DMX start address TEST Test program of all functions AUDI ASLW Self running audio program slow AFST Self running audio program fast MSTR Master for the audio program SPT Basic position for the audio program SIZE Size for the audio program NORM BIG MIDL SMAL LAMP Switch on of the lamp direct at the Power Spot 700 M RESE Reset O TIME PONR Running time of the fixture no destructible LA Running time of the lamp erasable z LAC Running time of the lamp no destructible RPAN Reverse Pan direction 9 m Reverse Tilt direction 4y JMD NORM DMX Mode Defines the number of DMX channels EXT DMX Mode NORM has to be selected at the moment SPEC MANU Manual drive of all device functions LRRU Automatic lamp start BLOF Switch off lamp via DMX DMX Reed out actual DMX values JISP p Gn Display On Off REN Twist the display also
16. carton appears to be damaged carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting customer support at the number listed below CUSTOMER SUPPORT Elation Professional provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions For service related issue please contact Elation Professional Service Hours are Monday through Friday 8 00 a m to 5 00 p m Pacific Standard Time Voice 866 245 6726 Fax 323 832 9142 E mail support elationlighting com Forum www ElationLighting com forum Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty Please do not discard the shipping carton in the trash Please recycle whenever possible WARRANTY REGISTRATION The Power Spot 700 II carries a two year 730 days Elation Professionals Los Angeles Ca wwww ElationLighting com Page 5 Power Sp
17. data transmission Your cables should be made with a male and female XLR connector on either end of the cable Also remember that a DMX line must be daisy Elation Professionals Los Angeles Ca wwww ElationLighting com Page 19 Power Spot 700 IIT chained and cannot be split unless using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch 4 COMMON DMX512 OUT m o DMX512 IN Be sure to follow the above figure when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior DMX Output DMX Input DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 1 Ground 2 Data 2 Data 3 Data 3 Data 4 Open 5 Open DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head Please refer to the diagram below You can chain multiple moving heads together through serial linking The cable needed should be two conductor shielded cable with XLR input and output connectors Always be sure daisy chain your in and out data connections never split or Y your DMX connections unless you are using an appro
18. pushing Up Down keys at the same time LHEA Function not yet in use L BAS Function not yet in use TEMP Internal Temperature Reading Elation Professionals Los Angeles Ca wwww ElationLighting com Page 23 Power Spot 700 IIT FANS HIGH Reed out internal temperature REG Maximum cooling fan velocity LOOF Automatic cooling fan control LOHI Low cooling fan speed gt lamp off A DJU CODE Use the code for entering the calibration menu for X XX authorized persons only COLI Calibration of the color wheel 1 COLE Calibration of the color wheel 2 DUR Calibration of the gobo wheel 1 DU HO Calibration of the gobo wheel 2 6033 Calibration of the gobo wheel 3 SH T Calibration Shutter Top side SH P Calibration Shutter Bottom side PRIS Calibration of the prism wheel IRIS Calibration of the iris POFS Calibration of the Pan Offsets TOFS Calibration of the Tilt Offsets LIRE Settings in the internal memory super user only ARES Adjust Reset wheels stand still after the reset VII Software version Tilt board NTR Software version driver board 1 Vd Software version driver board 2 VIR Software version driver board 3 DRUG Function not yet in use COND CODE Use the code for entering the calibration menu for X XX authorized persons only COLO Coarse calibration of the color wheel 2 COL I C
19. that require low ambient noise In this setting the fan will operate at the lowest speed When the maximum internal intolerable operating temperature is reached the lamp will automatically shut off LOHI In this setting the fan will operate at the lowest speed When the maximum internal intolerable operating temperature is reached the fan will automatically switch from low to high speed Elation Professionals Los Angeles Ca wwww ElationLighting com Page 30 Power Spot 700 IIT 8 9 8 Adjustments and Calibrations AJUU With this function you can adjust and calibrate the positions of the different wheels and other motors This feature is reserved for a service technician and is sometimes required after a service or repair work This function requires a service code only available to authorized service technicians Use the Up and Down buttons to select the function that requires calibration and press the Enter button to confirm the adjustment or the Mode button to cancel and return to the menu Use the Up and Down buttons to set the adjustment values and confirm once more with the Enter button or use the Mode button to cancel the operation Function Value Remark ADJU CODE XXXX Adjustments in the internal setup are code protec ted for authorized persons only COLI 99 99 Adjustment of the Color wheel 1 CULe 99 99 Adjustment of the Colo
20. the reflective side of the gobo is sometimes hard to distinguish An easy way to distinguish the reflective side is to hold a pencil directly in front of the Gobo If the pencil is in front of the uncoated side of the gobo you will see thickness of the Glass Gobo between the mirror image and the pencil This is the reflective side that should be mounted towards the lamp See the illustration on the next page notice the pencil image on the left has a mirror reflection further away from the pencil as the mirror reflection on the right Elation Professionals Los Angeles Ca wwww ElationLighting com Page 55 Power Spot 700 IIT Attention Custom gobos that contain company logos and text must also be orientated properly to ensure proper display of the custom image The readable side must be mounted towards the lamp In the illustration below notice that the text is readable in the example on the left and mirrored in the example on right The illustration below details proper gobo placement Be sure that all custom gobos are ordered so that their reflective side is on the readable side of the image as detailed in the example on the left Textured Glass Gobos must be mounted with the textured surface towards the lamp and the flat side towards the front lens Colored Dichroic Filters are already pre mounted on the color filter holder that guarantees the correct orientation Elation Professionals Los Angeles Ca wwww El
21. to 1 the second unit to 22 21 1 the third unit to 43 21 22 and so on Note During start up the Power Spot 700 II will automatically detect whether a DMX data signal is being received or not If DMX data signal is being received the display will show D XXX XXX representing the actual DMX address If the fixture is not receiving a DMX signal the display will flash D XXX XXX representing the actual DMX address If your fixture is connected to a DMX controller and the display is flashing not receiving a DMX signal please check the following The 3 PIN or 5 PIN XLR input plug cable with DMX signal from controller is not connected or is not inserted completely into the DMX input jack of the fixture The DMX controller is switched off or defective The DMX cable or connector is defective A DMX terminator has been inserted into the last fixture in your DMX chain Elation Professionals Los Angeles Ca wwww ElationLighting com Page 22 Power Spot 700 IIT 8 FIXTURE MENU The control panel located on the side of the fixture allows you to access the main menu and make all necessary adjustments to the POWER SPOT 700 During normal operation tapping the MODE key once will access the fixture s main menu Once in the main menu you can navigate through the different functions and access the sub menus with the Up and Down buttons Once you reach a field that requires adjusting tap the ENTER
22. ve reached the most even beam projection Note A slight hotspot will always remain and is conditional to the optical path Elation Professionals Los Angeles Ca wwww ElationLighting com Page 49 Power Spot 700 IIT 12 FUSE REPLACEMENT Caution Always replace with the exact same type fuse unless otherwise specified by an authorized Elation service technician Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty Warning If you continue to blow fuses STOP using the fixture Contact customer support for further instructions you may have to return the unit for servicing Continuing to use the unit may cause serious damage Fuse Replacement Locate and remove the unit s power cord from the main power supply Once the cord has been removed located the fuse holders located on the side panel near the power input connection Using a flat head screwdriver unlock the fuse holder from its housing by turning the holder in a counter clockwise direction Once the fuse holder has been unlocked pull back on the fuse holder holder to expose the fuse Gently pull out the bad fuse and discard of it properly and replace it with an exact match Reassemble in reverse order Elation Professionals Los Angeles Ca wwww ElationLighting com Page 50 Power Spot 700 IIT 13 OPTICAL EFFECTS MODULE The Power Spot 700 Il is equipped with an optical effects module that can
23. 00 IIT b Insert the effects module back in to the fixture and the two lateral tracks Push it carefully down until the two locking thumbscrews snap in place and hand tighten the retaining thumbscrews c Connect the Data Bus cable into the proper corresponding socket d Seal the cover in reverse order Elation Professionals Los Angeles Ca wwww ElationLighting com Page 54 Power Spot 700 IIT 14 CHANGING REPLACING GOBOS COLORS Before attempting to change any gobos or color be sure to follow the effects module removal process as described in the previous section section 13 of this manual The POWER SPOT 700 Il includes both Aluminum thickness 0 3 mm and Glass thickness 1 1 3 0 mm gobos outside diameter 26 9 mm viewable image size 23 mm There is one rotating Gobos wheel user replaceable gobos and one fixed Gobo wheel non replaceable gobos 14 1 General guidelines for exchanging Gobos and Colors All Gobos and Color filters have a specific optical orientation that must be observed To prevent damage to the gobos and color filters and to optimize the optical image all effect should be mounted with their reflecting side in the direction of the lamp For example Aluminum Gobos must be mounted with their unpainted side toward the lamp The black painted side should go in the direction of the front lens Glass Gobos must be mounted with their reflective side toward the lamp In the case of glass gobos
24. 24 25 18 19 9 6 Color 6 Color 7 fast 26 27 1A 1B 10 4 Color 7 Orange fast 28 29 1C 1D 11 2 Color 7 Color 8 fast 30 31 1E 1F 12 0 Color 8 Dark Blue fast 32 33 20 21 12 7 Color 8 Color 9 fast 34 35 22 23 13 5 Open fast 36 63 24 3F 15 25 Open slow Chaser from color to 64 65 40 41 25 3 Open Color 1 Slow CODE TAG TABEN 66 67 42 43 26 1 Color 1 Red slow P RES 68 69 44 45 26 9 Color 1 Color 2 slow 70 71 46 47 27 6 Color 2 Magenta slow 72 73 48 49 28 4 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 37 Power Spot 700 IIT Channel Function Time and Value DMX HEX Color 2 Color 3 slow 74 75 4A 4B 29 2 Color 3 Purple slow 76 77 4C 4D 30 0 Color 3 Color 4 slow 78 79 4E 4F 30 8 Color 4 Blue slow 80 81 50 51 31 6 Color 4 Color 5 slow 82 83 52 53 32 4 Color 5 Green slow 84 85 54 55 33 1 Color 5 Color 6 slow 86 87 56 57 33 9 Color 6 Yellow slow 88 89 58 59 34 7 Color 6 Color 7 slow 90 91 5A 5B 35 5 Color 7 Orange slow 92 93 5C 5D 36 3 Color 7 Color 8 slow 94 95 5E 5F 37 1 Color 8 Dark Blue slow 96 97 60 61 37 8 Color 8 Color 9 slow 98 99 62 63 38 6 Open slow 100 127 64 7F 40 50 Color Rotation STOP 128 129 80 81 50 1 Color r
25. 6 Power Spot 700 IIT 1 INDEX A Adjustments 23 aspheric lens 40 B BOC zau eat dota ia aaa a at aa 11 Blind current compensation 13 C Calibrations 23 Change a Gobo 37 Connected load 13 D Pe 6orati on E 11 Description of Device 8 DIN VDE 0711 217 11 DMX e n dna asa natie ists batt 13 II ME ee 18 DMX Protocol EE 29 E Error Messages 25 F Feedback 25 Fixture Temperature 23 USO simi 27 aa aa oua e Ada Su ka S kay mA 15 G Glass Gob0S E 38 Elation Professionals Los Angeles Ca I Injury of the retina M Maintenance Measures su ta aia de atasa aa side a Mounting soere eeose eere P Pan movement Power SUPPI caca un iai esr S Safety Instructions Secure the Power Spot 7000 Special EFunchons T Technical Gpechfcaton Test Program Tilt movement wwww ElationLighting com Page 67 Power Spo
26. BF 63 75 Lying eight Size phase see also PAN 192 223 CO DF 76 87 Random movement Size see also PAN 224 255 E0 FF 88 100 21 Speed Pan Tilt relative movement 0 15 00 0F 0 6 Pan Tilt Pan Tilt slow fast Pan Min 530 200 s 16 255 10 FF 7 100 Channels 1 3 and 23 Pan Max 530 2 65 s Tilt Min 285 110 s Tilt Max 285 1 8 s Elation Professionals Los Angeles Ca wwww ElationLighting com Page 45 Power Spot 700 IIT Lamp ON Shutter open Channel 12 240 25 FO F 94 10 5 F 0 Fam Lamp OFF min 3 sec if Channel 19 and 230 24 6E 9 92 97 p Shutter closed 000 Channel 12 9 F 0 OFF 0 0 Channel 19 250 25 FA F 98 10 Reset 5 F 0 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 46 Power Spot 700 IIT 11 LAMP REPLACEMENT For a proper and safe lamp change please read this chapter carefully and follow all instructions Safety Regulations Pull out the main plug Wait min 20 minutes after the last operation to cool down the fixture Don t touch the bulb of the lamp with bare fingers this can cause damages Before you put the POWER SPOT 700 into operation close the casing otherwise your retina can be hurt Replace the lamp with an approved replacement type Be sure to follow all the lamp handling procedures included with your new lamp Never handle the new lamp with your bare
27. CTAUOMS EE 51 13 2 Removing the Effects Module a mana amana aaa 51 14 Changing Replacing Gobos Colors mnneeeeeeeeeeeeeeeeee eee 55 14 1 General Guidelines EE 55 14 2 Changing GODOS EE 57 E REEL Un eege IC 57 14 42 Gobo PattermsS au uuu su ul al dei Sote at adu a d d 58 15 Maintenance and Cleanng AE 59 10 Warianty u u heed eeh daia e 61 17 Photometrie Data EE 63 18 Dimensions uuu u uuu au DAS i a ia bau i aaa ae 64 19 Technical Specification nenea eee 65 20 Index D T uD DI Bazine eee o otet at aa du ae ui ae ata uta 67 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 4 Power Spot 700 IIT INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The Power Spot 700 II has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance UNPACKING Thank you for purchasing the Power Spot 700 II by Elation Professional Every Power Spot 700 II has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the
28. Functions SPEC uuu ceea Bee dot oa pa oa ae Baci EE ae aaa 8 9 1 Manual Drive OC E seca ae aa ae pile aia 093 20 a at ai ia da 8 9 2 Lamp On automatic AA 8 9 3 Lamp Off via DMX zeci pica aaa iat AGI io poe een pna at di a nds 8 9 4 DMX Input UE 8 9 5 LED Display DISP uuu uu susunan EE a 8 9 6 Fixture Temperature TEMP onoarea ee aa aaa 8 9 7 Fan Gontrol FANS EE Elation Professionals Los Angeles Ca wwww ElationLighting com Page 3 Power Spot 700 IIT Power Spot 700 IIT 8 9 8 Adjustments and Calibrations ADJU 31 8 9 9 Defauii Settings DE EE 32 8 9 10 Feedback FEED assasi a ae na aaa ai ta aaa d 32 8 9 11 Fault Corrections EFLD ss sie a aa aa ata ae al a aia aa 32 8 10 Error and Information Messages aaa aaaaaaanaoaonee ea 32 9 Operating Node 2c caiac ali a ea ial a ala Da Da i eee iii 34 9 1 Universal RK LEE 34 9 2 Stand Alone Sound Active eee ramanea a ma aaa m na 34 9 3 Master SlaVezu a u u uu aie aprenden reo paun di u d cota es Ae 35 10 DMX Channel Traits DMX Protocol eee 37 11 Lamp Re eplacement u u sula alt iei da oi La ai ae 47 11 1 Safety Regulations EE 47 11 2 Lamp Optimization insasi aaa E 48 12 Fuse Replacement EE 50 13 Optical Effects Module u uu u nt ada a pl ca 0 lu dal i a 51 13 1 Safety CONSIA
29. IIT GORE 000 255 Gobo wheel 2 GRTe 000 255 Gobo wheel 2 rotation 6023 OOO 255 Gobo wheel 3 SHUT ODD 255 Shutter Strobe functions Lamp will strike at a channel value of 255 if the dimmer channel is ata value of 255 Open DIMR 000 255 Dimmer FOCU GGG 255 Focus ZOOM OOO 055 zoom FRST OOO 255 Frost PRIS 000 255 Prism 000 127 Stop Prism rotation IRIS GOO 255 Iris SPEC DDD 255 Lamp Off Reset MONE OOO 255 Movements SPED 000 255 Speed for Pan Tilt 8 9 2 Lamp On automatic lamp strike LAAU This function automatically strikes lamp when main power is turned on If you would prefer to strike the lamp through a DMX controller you must turn this function off To toggle between OFF and ON use the Up and Down buttons Use the Enter button to confirm your setting Please note ON is the default setting for this function 8 9 3 Lamp Off via DMX DLOF This function allows the lamp to be switched off through a DMX controller To enable this function use the Up and Down buttons to toggle between ON and Off Turn this function ON to allow DMX switching Use the Enter button to accept your selection or the Mode button to cancel and return to the menu 8 9 4 DMX Input BMX Elation Pro
30. IT Mode button to cancel and return to the main menu 8 8 Invert Tilt Movement RILT This function allows you to invert all tilt movements Use the Up and Down buttons to turn this function On and Off Press the Enter button to accept the change or the Mode button to cancel and return to the main menu 8 9 Special Functions SPEC This menu option accesses several special features and function of the POWER SPOT 700 The SPEC sub menu consists of several sub menus Navigation details of the special functions and their sub menus are as followed 8 9 1 Manual Drive MANU This feature allows you to drive all the unit s functions manually for use in an environment that requires a static position no movements determining focus points or testing Use the Up and Down buttons to select the function you wish to adjust then use the Enter button to accept your selection Now adjust the values with the Up and Down buttons and use the Enter button to lock in your value Use the Mode button to cancel at any time Function Value Remark PAN ODO 255 Pan Position TILT OOO 255 Tilt Position COL I 000 255 Color wheel 1 COL 000 255 Colorwheel2 603 000 255 Gobo wheel 1 GRT I 000 255 Gobo wheel 1 rotation Elation Professionals Los Angeles Ca wwww ElationLighting com Page 27 Power Spot 700
31. M 66 67 42 43 26 1 Color 1 Brilliant Blue slow ka 68 69 44 45 26 9 Color 1 Color 2 slow 70 71 46 47 27 6 Color 2 Green slow 72 73 48 49 28 4 Color 2 Color 3 slow 74 75 4A 4B 29 2 Color 3 Pink slow 76 77 4C 4D 30 0 Color 3 Color 4 slow 78 79 4E 4F 30 8 Color 4 Red slow 80 81 50 51 31 6 Color 4 Color 5 slow 82 83 52 53 32 4 Color 5 Yellow slow 84 85 54 55 33 1 Color 5 Color 6 slow 86 87 56 57 33 9 Color 6 Light Green slow 88 89 58 59 34 7 Color 6 Color 7 slow 90 91 5A 5B 35 5 Color 7 CTO Filter slow 92 93 5C 5D 36 3 Color 7 Color 8 slow 94 95 5E 5F 37 1 Color 8 CTC Filter slow 96 97 60 61 37 8 Color 8 Color 9 slow 98 99 62 63 38 6 Open slow 100 127 64 7F 40 50 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 39 Power Spot 700 IIT Channel Function Time and Value DMX HEX Color Rotation STOP 128 129 80 81 50 1 Color rotation slow fast CW Min 1 4 turns h 130 191 82 BF 51 75 Color rotation fast slow CCW Max 2 9 turns sec 192 253 CO FD 76 98 Audio color chaser slow Each 4 sound impulse 254 FE 99 gt new color Audio color chaser fast Each sound impulse gt 255 FF 100 new color 7 Gobo 1 Gobo 1 open fast Chaser from gob
32. acked up and retained by an internal power source with a five year shelf life 8 2 Test Program 8 3 TEST The Test Program engages the fixture s internal test mode This function runs a complete test procedure of all functions Press Enter to launch the self test or the Mode button to cancel and return to the main menu Audio Program AUD The Audio menu allows you to run a stand alone audio program This program can run either fast AFST or slow Aslw Fast AFST When running in fast mode every sound impulse will trigger a new step Aslw When running in You may run several fixtures together at once to achieve a synchronized light show running to sound in a Master Slave configuration Additionally you can choose a basic position for this audio chaser Use either the internal manual mode or an external DMX controller to set the desired Pan Tilt position Confirm this setting in the SVPT menu by pressing the Enter button You can also set the size of the audio chaser in the SIZE menu You have the choice between NORM no basic position has to bee chosen BIG MIDL and SMAL If you want to run several units in a Master Slave system be sure designate your first unit in the chain as the master All others must be Slave Master OFF Notice The Audio function is only working if no DMX is connected Elation Professionals Los Angeles Ca wwww ElationLighting com Page 25
33. allows you to choose the approximate size of the room NORM BIG MIDL SMAL The built in programs will automatically adjust to your selection to optimize light output for your room Use the sound sensitivity knob on the side control panel to make the unit more or less sensitive to sound Turning the knob in clockwise direction will make the unit more sensitive to sound while turning the knob counter clockwise will make the unit less sensitive to sound Note This unit will react to the low frequencies of a sound source tapping on the fixture or high pitched sound may not trigger the fixture 9 3Master Slave Operation Sound Active This function will allow you to link up to 16 fixtures together and operate without a controller The fixtures will be sound activated In Master Slave operation one fixture will act as the controlling fixture and the others will react to the controlling fixtures programs Any fixture can act as a Master or as a Slave 9 3 1 9 3 2 Using standard XLR microphone cables daisy chain your fixtures together via the XLR connector on the rear of the fixtures Remember the Male XLR connector is the input and the Female XLR connector is the output The first fixture in the chain master will use the female XLR connector only The last fixture in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture Follow the same procedures listed in the prev
34. anufactured Elation Professionals Los Angeles Ca wwww ElationLighting com Page 61 Power Spot 700 IIT F No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professionals in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professionals be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to Elation Professionals products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published H Lamps are not covered under this or any other warranty either written or implied Elation Professionals Los Angeles Ca wwww ElationLighting com Page 62 Power Spot 700 IIT 17 PHOTOMETRIC DATA Power Spot 700 Photometric Data illuminance lux or fe 602500 cd distance m or ft
35. ationLighting com Page 56 Power Spot 700 IIT 14 2 Changing Gobos 1 Be sure the effects module is removed and opened as detailed in the previous section of this manual 2 Genteelly lift and pull the gobo holder out of the center part of the wheel hub to remove the individual holder See the left image below 3 Once the gobo holder has been removed the Gobo itself can be replaced 5 by remove the centric spring with a small screwdriver or gripping pliers Be sure to follow the gobo alignment instructions that are detailed on the previous page of this manual section 14 1 Once the gobo has been exchanged replace the retaining centric spring to hold the gobo in position Place the Gobo holder assembly back into the gobo wheel central hub A slight snap will ensure that the gobo holder has been correctly and fully inserted back into the gobo wheel hub Notice There must be no gap between the gobo holder assembly and the actual gobo wheel Be sure to check for a complete and secure fit 14 3 Changing Color filters 1 Be sure the effects module is removed and opened as detailed in the 3 previous section of this manual section 13 1 Pull the Color filter holder carefully out of the central locking spring holder Be sure to grasp the color filter by the metal frame and by the glass filter itself Replace the colored filters as needed by inserting the replacements back into the color whe
36. be easily removed for cleaning service and gobo color exchange Please follow the procedures below for proper removal and service of the effects module 13 1 Safety considerations Always remove main power before attempting any type of service procedure f the fixture has been recently in operation please allow 15 minutes for the internal components to cool before attempting service During service never touch the lamp with bare fingers as this can damage the lamp and reduce lamp life To prevent personal injury from UV radiation always be sure the cover is replaced before operating the fixture 13 2Removing the optical effects module 1 Please lock the head in a vertical position for easier access 2 Remove the upper shell of the head casing by loosening the four quick release retaining fasteners Two on the front side and two on the backside of the head Hang out the head safety 3 Disconnect the main Data Bus cable from the optical effects module This is the only connection between the effects module and the fixture s head control board No other bus cables need to be removed See illustration below Elation Professionals Los Angeles Ca wwww ElationLighting com Page 51 Power Spot 700 IIT
37. ce should be at least 5 meter about 1 5ft Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environment always be to use mounting hardware no less than M10 x 25 mm also be sure the hardware is insert in the pre arranged screw holes in the base of the fixture When using the quick release Omega cam lock system be sure the four quick lock fasteners are locked in the quick lock holes correctly see page 16 for more information on the proper mounting procedures Do not attempt to operate this fixture until you have familiarized yourself with its functions Do not permit operation by persons not qualified for operating this type of theatrical fixture most damages are the result of operation by person unfamiliar with the operation of this type of fixture If service is ever required please use the original packaging to transport the fixture in for service Elation Professionals Los Angeles Ca wwww ElationLighting com Page 10 Power Spot 700 IIT Transportation and Handling The POWER SPOT 700 II comes with two carrying handles built into the base Always transport the fixture by these handles Never lift or carry the POWER SPOT 700 II by the yoke head assembly this can seriously damage the unit and will void your manufactures warranty Connections Power supply Electronic ballast with 90 260 Volts 50 60 Hz Grounded contact type plug Neutrik
38. cedures Safety Considerations Always disconnect main power before attempting any service related issues Allow ample time for the lamp to cool at least 20 minutes before performing any cleaning procedures Never attempt operation with any of the protective covers removed Cleaning Frequency rule of thumb The residue build up will very depending on location therefore only general guidelines are given Below is a suggested cleaning interval only Cleaning frequency depends on the environment in which the fixture operates I E smoke fog residue dust dew In clubs that observe heavier use we recommend cleaning on a more frequent basis Periodic cleaning will ensure fixture longevity and crisp lamp output Position Interval In this way Outside optic Weekly Soft cloth and glass cleaner Color filter Monthly Soft cloth and glass cleaner Gobos Yearly Vacuum cleaner airbrush etc Glass gobos Monthly Soft cloth and glass cleaner Prism Monthly Soft cloth and glass cleaner Dimmer Shutter Yearly Vacuum cleaner airbrush etc Elation Professionals Los Angeles Ca wwww ElationLighting com Page 59 Power Spot 700 IIT Inside lens Monthly Soft cloth no glass cleaner Fan and air channel Monthly Vacuum cleaner airbrush etc Reflector Never Lamp Never Moveable parts Yearly Suitable Lubricant Caution 1 Never allow the optical parts to come in contact with oil dirt or grime 2 Allow all parts to dry comp
39. e accomplished by pressing both the UP and DOWN buttons at the same time Elation Professionals Los Angeles Ca wwww ElationLighting com Page 29 Power Spot 700 IIT 8 9 6 Fixture Temperature TEMP This function allows you to read out the actual fixture operating temperature Press the Enter button to select this function or the Mode to button to cancel and return to the main menu Normal operating temperature should range between 85 C and 95 C Operating temperatures between 96 C and 104 C are considered critical Temperatures above 105 C will send the fixture into protect mode and automatically switch the lamp off the lamp will remain off until internal temperature drops below 95 C Outside surface temperature should not exceed 45 C 8 9 7 Fan Control FANS By using this function you can choose between 4 types of fan speed operations Use the Up and Down buttons to select the desired fan setting then press Enter to accept your setting or press the Mode button to cancel and return to the menu The chart below will detail the different fan settings HIGH The cooling fan works continuously at max speed REG This is the default fan setting In this setting an internal thermal sensor constantly monitors the internal operating temperature and regulates the fan speed to coincide with the internal temperature LOOF This function is designed for environments
40. el s central retaining spring If necessary you may use a small flathead screwdriver to carefully lift the center retaining spring on the color wheel up Notice Please be sure the color filter holder is snapped in completely Failure to do so may result in damage to the color filter Elation Professionals Los Angeles Ca wwww ElationLighting com Page 57 Power Spot 700 Ii Power Spot 700 II Gobo Wheels Special Notice If you use glass gobos the non vaporized side must be fitted towards the lamp direction gi Magnet Fixed Gobo wheel Elation Professionals Los Angeles Ca wwww ElationLighting com Page 58 Power Spot 700 IIT 15 MAINTENANCE AND CLEANING It is absolutely essential that the fixture is kept clean and dust dirt and smoke fluid residues do not built up on the surface or within the fixture Residue build up may cause the fixture s light output to be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliable throughout its life A soft lint free cloth moistened with any quality glass cleaner is recommended under no circumstances should alcohol or solvents be used Stay away from glass cleaner that contains ammonia such as Windex The inside optical system should be maintained only by qualified technicians Please contact Elation professionals for recommendation associated with internal cleaning pro
41. fessionals Los Angeles Ca wwww ElationLighting com Page 28 Power Spot 700 IIT This function will display the DMX value of a channel in the LED as the fixture receives it Use the Up and Down buttons to select desired channel and press Enter to read its value Function Value Remark PAN 000 255 Pan Position TILT GGG 255 Tilt Position COL I OOO 255 Color wheel 1 COLO 000 955 Color wheel 2 603 ODO 055 Gobowheel1 GRT 000 255 Gobo wheel 1 rotation 6032 000 255 Gobo wheel 2 GBRT2 000 255 Gobo wheel 1 rotation 6033 ODO 055 Gobo wheel 3 SHUT 000 255 Shutter Strobe function IMR 000 055 Dimmer FOCU 000 255 Focus Z00M DUU 255 zoom FRST DUU 255 Frost PRIS 000 255 Prism wheel 000 127 Stop Prism Rotation IRIS 000 255 iris SPEC OOU 55 Lamp Off Reset MONE 000 255 Movement SPE ODO 055 Speed for Pan Tilt 8 9 5 Display JISP Use this function to choose between different display indications Use the Up Down keys to select desired function and press Enter to confirm or Mode to cancel and return to the menu Df Display On Off If you ve chosen off the display will go out within 15 seconds after the last input The next key touch will reactivate the display REV Rotates the display by a 180 This may also b
42. hands the oils from your skin may damage the lamp Always replace with the lamp with a lamp that meets the original lamp specification failure to do so may damage the unit and will void your manufactures warranty Lamp Change 1 Be sure the unit s main power is disconnect before attempting any service procedure 2 Always allow ample time for the unit to properly cool before attempting any type of service or repair 3 To allow the best lamp access use the tilt lock system to lock the head in 180 horizontal position eA JARNING eeng AC power efore te lampina _ al is Risk o E Sri Til Omeekthescrews 1 2 3 and 4forre lamping 4 Using a standard flat head screwdriver release 1 4 turn quick lock fasteners labeled 1 2 3 and 4 of the backside lamp sheet and remove it carefully These Elation Professionals Los Angeles Ca wwww ElationLighting com Page 47 Power Spot 700 IIT fasteners will remain connected to the lamp socket cover 5 Gently remove the old lamp from it s socket If the old lamp has exploded be sure to remove all of the old lamp fragments to prevent damage to the internal components 6 Insert the new lamp securely locking the OK y lamp in place as illustrated in the diagram ges to the left Orientate the lamp filler tube towards the backside of the reflector Before reassembling the unit be sure the new lamp is securely seated in the lamp socket Always be sure to only use s
43. ing from epilepsy should avoid looking directly into the lamp at all times Avoid switching the fixture on and off repeatedly in short intervals as this will reduce lamp life and intensity To achieve the intensity associated with discharge lamps these lamps use a gas sealed in a high pressure environment to emit a brilliant output Due to the high pressure involved with the construction of the lamp the lamp may explode during prolonged extensive use This risk is increased with age added care is encouraged when dealing with older lamps Thus lamp should always be replaced at the end of their recommended duty cycle Extreme caution should be used when operated this or any fixture fitted with a gas discharge lamp Elation Professionals Los Angeles Ca wwww ElationLighting com Page 6 Power Spot 700 IIT Never open this fixture while in use During the initial operation of this fixture a light smoke or smell may emit from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp This device falls under protection class 1 Therefore it is essential that the device be grounded properly All electrical connections must performed by qualified personal Be sure the available voltage matches the voltage requirements of the unit Be sure the power cord is never crimped or damaged If the power cord is damaged replace
44. installation position 2 Color Wheels o Color Wheel 16 User exchangeable colors 3 Gobo Wheels o Fixed 9 plus open o Rotating 14 User replaceable plus open Auto test for all functions Automatic Pan Tilt Correction Glass Dichroic Reflector for Even Lamp Output Anti Reflective Coated Lenses Brilliant MSR700 2 Lamp 700w 1000Hrs 7200K USITT DMX 512 Complaint Value of each DMX channel can be displayed Uses 24 DMX Channels 16 bit mode Variable Frost Filter 3 Facet Prism User Replaceable Color and Gobos Intergraded Tilt Lock System Modular Construction Variable Zoom 14 32 Beam Angle Motor Driven Focus Variable Iris 4 100 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 9 Power Spot 700 IIT 4 GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage in nightclubs in theatres etc Do not attempt operation or installation without a proper knowledge on how to so This fixture was designed for indoor use only Consistent operational breaks may ensure that the fixture will function properly for many years to come Do not shake the fixture around Avoid brute force when installing or operating the device While choosing an installation location please be sure that the fixture will not be exposed to extreme heat moisture or dust The minimum distance between the fixture and a wall or flat surfa
45. ious Stand Alone section Elation Professionals Los Angeles Ca wwww ElationLighting com Page 35 Power Spot 700 IIT With two exceptions be sure the first unit in the chain is selected as the master MSTR is turned on in the audio submenu All other fixtures must be in slave mode SVPT turned on in the audio submenu Elation Professionals Los Angeles Ca wwww ElationLighting com Page 36 Power Spot 700 IIT 10 DMX CHANNEL TRAITS DMX PROTOCOL Channel Function Time and Value DMX HEX 1 Pan 0 530 Min 2 65 s 0 255 00 FF 0 100 2 Pan fine High Pos High Pos 2 1 16 Bit 0 255 00 FF 0 100 3 Tilt 0 285 Min 1 8 s 0 255 00 FF 0 100 4 Tilt fine High Pos High Pos 1 1 16 Bit 0 255 00 FF 0 100 5 Color 1 Open fast Chaser from color to 0 1 00 01 0 2 fast Open Color 1 fast SSES SEN 2 3 02 03 1 0 Color 1 Red fast EE 4 5 04 05 18 Color 1 Color 2 fast 6 7 06 07 2 5 Color 2 Magenta fast 8 9 08 09 3 3 Color 2 Color 3 fast 10 11 0A 0B 4 1 Color 3 Purple fast 12 13 0C 0D 4 9 Color 3 Color 4 fast 14 15 OE 0F 5 7 Color 4 Blue fast 16 17 10 11 6 5 Color 4 Color 5 fast 18 19 12 13 7 3 Color 5 Green fast 20 21 14 15 8 0 Color 5 Color 6 fast 22 23 16 17 8 8 Color 6 Yellow fast
46. it immediately with a new one of similar power rating Always disconnect from main power before performing any type of service or any cleaning procedure Only handle the power cord by the plug Never pull out the plug by tugging the wire portion of the cord Please be aware that damages caused by modifications to the device are not subject to warranty Elation Professionals Los Angeles Ca wwww ElationLighting com Page 7 Power Spot 700 IIT 2 SAFETY INSTRUCTIONS The Power Spot 700 II is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual Always be sure that the fan and the air inlets remain clean and are never blocked Allow about 6 15cm between this fixture and other devices or a wall to allow for proper cooling Never touch the fixture during normal operation This can cause severe personal injuries and or damage to the fixture Be sure to unplug the POWER SPOT 700 II from the power outlet before performing any service related issues Lamp Replacement Allow at least 30 minutes after disconnecting main power before you open the POWER SPOT 700 II To prevent personal injury never touch the lamp if you are not absolu
47. l 3 9 fixed exchangeable standard gobos plus open 11 spare Gobos included Gobo outside diameter 26 9 mm image size 23 mm Gobo thickness glass 1 1 3 0 mm aluminum 0 3mm Gobo wheel 2 9 fixed aluminum Gobos plus open fixed Shutter Strobe Dimmer 16 Bit Strobe effect with variable speed 1 10 flashes per second Continuously mechanical dimmer 0 100 Prism 16 Bit Rotating 3 face prism rotating and variable in speed Focus 16 Bit Motor driven focus from near 2m to far away Iris 16 Bit High Speed Iris 100 4 0 2 Sec opening time Zoom 16 Bit Zoom range 14 32 Drive Elation Professionals Los Angeles Ca wwww ElationLighting com Page 65 Power Spot 700 IIT Standard DMX 512 3 pole XLR Pin 3 Pin2 Ground Pin 1 The DMX addressing starts at the DMX address 001 Pan Tilt Pan movement 530 in max 2 65 seconds 16 bit resolution Tilt movement 280 in max 1 68 seconds 16 bit resolution Weights and measures Width of the base 490 mm 19 3 Length of the base 380 mm 15 Height head vertical 646 mm 25 5 Weight net 28 5 kg 63lbs Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice Elation Professionals Los Angeles Ca wwww ElationLighting com Page 6
48. letely before attempt operation 3 Never clean the aspheric lens with water or other cleaners The lens should be changed at the first sign of ware usually in about 1 2 years lens will begin to look cloudy For lens replacement please contact Elation technical support Elation Professionals Los Angeles Ca wwww ElationLighting com Page 60 Power Spot 700 IIT 16 TWO YEAR 730 DAYS LIMITED WARRANTY A Elation Professionals hereby warrants to the original purchaser Elation Professionals products to be free of manufacturing defects in material and workmanship for a period of two years 730 days from the date of purchase This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the Elation Professionals factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty Elation Professionals will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any accessories are shipped with the product Elation Professiona
49. lified staff should attempt installation Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION Be sure a qualified electrician performs all electrical connections Be sure to complete all rigging and installation procedures before connecting the power cord to the appropriate wall outlet Clamps The POWER SPOT 700 II has been designed to hold multiple clamps to the bottom of the unit in several different orientations Always use an appropriately rated clamp to mount this unit to truss Refer to the printed instructions on the bottom of the fixture for proper clamp installation a Cam lock System This system allows a quick and efficient means to secure a Clamp to the unit To attach a clamp to the unit attach a clamp that is rated to handle the weight of the unit to your cam lock After a clamp has been attached to the cam lock attach the cam locks to the designated position on the bottom of your unit Lock the cam locks into position by turning the wing nuts 90 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 17 Power Spot 700 IIT
50. ls shall have no liability whatsoever for loss of or damage to any such accessories or for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which Elation Professionals concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the Elation Professionals factory unless prior written authorization was issued to purchaser by Elation Professionals if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above Elation Professionals will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professionals under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of Elation Professionals All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that effect E Elation Professionals reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore m
51. o to 0 7 0 7 0 2 9 indexed Gobo 2 fast SSES 8 15 8 F 3 59 Gobo 3 fast BEE 16 23 10 17 6 8 9 Gobo 4 fast 24 31 18 1F 9 11 9 Gobo 5 fast 32 39 20 27 12 14 9 Gobo 6 fast 40 47 28 2F 15 17 9 Gobo 7 fast 48 55 30 37 18 20 9 Gobo 8 fast 56 63 38 3F 21 23 Gobo 1 open slow Chaser from gobo to 64 71 40 47 24 26 9 Gobo 2 slow Jobo MAAA BPM 72 79 48 4F 27 29 9 Gobo 3 slow CS E 80 87 50 57 30 33 9 Gobo 4 slow 88 95 58 5F 34 36 9 Gobo 5 slow 96 103 60 67 37 39 9 Gobo 6 slow 104 111 68 6F 40 42 9 Gobo 7 slow 112 119 70 77 43 45 9 Gobo 8 slow 120 127 78 7F 46 49 Gobo rotation STOP 128 129 80 81 50 Gobo rotation slow fast CW Min 1 4 turns h 130 191 82 BF 51 75 Gobo rotation fast slow CCW Max 1 0 turns sec 192 253 CO FD 76 98 Audio gobo chase slow Each 4 sound impulse 254 FE 99 gt new gobo Audio gobo chase fast Each sound impulse gt 255 FF 100 new gobo Elation Professionals Los Angeles Ca wwww ElationLighting com Page 40 Power Spot 700 IIT Elation Professionals Los Angeles Ca wwww ElationLighting com Page 41 Channel Function Time and Value DMX HEX 8 Gobo 1 Gobo Position 0 540 0 127 00 7F 0 49 Posi Rot Gobo Rotation STOP 128 129 80 81 50 G
52. oarse calibration of the color wheel 1 DFSE Call on the default function values FEED Pan Tilt feedback error correction On Off EFLG Correction of faults 8 1 Setting Changing the DMX Address After applying power to the POWER SPOT 700 the LED will display the fixture s current DMX address immediately after the reset sequence If the fixture is not receiving a DMX signal the display will flash continuously JOC To set or adjust a DMX address please follow the procedure below 1 Switch on the POWER SPOT 700 and wait for the fixture reset process to finished RESE will flash in the LED while fixture is in reset mode Elation Professionals Los Angeles Ca wwww ElationLighting com Page 24 Power Spot 700 IIT 2 Press the Mode button to access the main menu Toggle through the menu by pressing the Up and Down buttons until the display shows D001 Tap the enter button to make changes to the address the current three digit address will immediately begin to flash 3 While the current three digit address is flashing use the Up and Down buttons to select adjust the address Lock your new address into the units memory by pressing the Enter button After the new address has been successfully stored into the fixture s memory the LED will briefly readout OK The DMX address is non destructible and will remain in the fixture s memory even when the power has been switched off Memory is b
53. obo Rotation Slow fast CW Min 2 0 turns h 130 191 82 BF 51 75 Gobo Rotation Fast slow CCW Max 3 8 turns sec 192 253 CO FD 76 100 Audio Gobo Rotation Slow Each 4 sound impulse 254 FE 99 gt new position Audio Gobo Rotation Fast Each sound impulse gt 255 FF 100 new gobo 9 Gobo 2 Gobo 1 open fast Chaser from gobo to 0 7 0 7 0 2 9 indexed Gobo 2 fast Bere Tien EECH 8 15 8 F 3 59 gt 0 Gobo 3 fast oS 16 23 10 47 6 8 9 Gobo 4 fast 24 31 18 1F 9 11 9 Gobo 5 fast 32 39 20 27 12 14 9 Gobo 6 fast 40 47 28 2F 15 17 9 Gobo 7 fast 48 55 30 37 18 20 9 Gobo 8 fast 56 63 38 3F 21 23 Gobo 1 open slow Chaser from gobo to 64 71 40 47 24 26 9 Gobo 2 slow SEET 72 79 48 4F 27 29 9 gt Gobo 3 slow ne 80 87 50 57 30 33 9 Gobo 4 slow 88 95 58 5F 34 36 9 Gobo 5 slow 96 103 60 67 37 39 9 Gobo 6 slow 104 111 68 6F 40 42 9 Gobo 7 slow 112 119 70 77 43 45 9 Gobo 8 slow 120 127 78 7F 46 49 Gobo rotation STOP 128 129 80 81 50 Gobo rotation slow fast CW Min 1 4 turns h 130 191 82 BF 51 75 Gobo rotation fast slow CCW Max 1 0 turns sec 192 253 CO FD 76 98 Audio gobo chase slow Each 4 sound impulse 254 FE 99 gt new gobo Audio gobo chase fast Each sound impulse gt 255 FF 100 Power Spot 700 IIT
54. ot 700 IIT limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support at 323 582 3322 DISCHARGE LAMP WARNING This fixture is fitted with a discharge lamp which is highly susceptible to damage if improperly handled Never touch the lamp with your bare hands as the oil from your hands d will shorten lamp life Also never move the fixture until the lamps have had ample time to cool Remember lamps are not covered under warranty conditions This fixture emits intense UV radiation which is harmful to the eyes and skin The intense luminance of the lamp can cause severe damage to the retina Never operate this fixture with the protective covers removed these covers have been specially designed to shield against UV radiation Epileptic Warning Those suffer
55. otation slow fast CW Min 1 4 turns h 130 191 82 BF 51 75 Color rotation fast slow CCW Max 2 9 turns sec 192 253 CO FD 76 98 Audio color chaser slow Each 4 sound impulse 254 FE 99 gt new color Audio color chaser fast Each sound impulse gt 255 FF 100 new color 6 Color 2 Open fast Chaser from color to 0 1 00 01 0 2 fast Open Color 1 fast color nay aO BEM 2 3 02 03 1 0 Color 1 Green fast SS ue 4 5 04 05 18 Color 1 Color 2 fast 6 7 06 07 2 5 Color 2 Brilliant Blue fast 8 9 08 09 3 3 Color 2 Color 3 fast 10 11 0A 0B 4 1 Color 3 Pink fast 12 13 OC 0D 4 9 Color 3 Color 4 fast 14 15 OE 0F 5 7 Color 4 Red fast 16 17 10 11 6 5 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 38 Power Spot 700 IIT Channel Function Time and Value DMX HEX Color 4 Color 5 fast 18 19 12 13 7 3 Color 5 Yellow fast 20 21 14 15 8 0 Color 5 Color 6 fast 22 23 16 17 8 8 Color 6 Light Green fast 24 25 18 19 9 6 Color 6 Color 7 fast 26 27 1A 1B 10 4 Color 7 CTO fast 28 29 1C 1D 11 2 Color 7 Color 8 fast 30 31 1E 1F 12 0 Color 8 CTC fast 32 33 20 21 12 7 Color 8 Color 9 fast 34 35 22 23 13 5 Open fast 36 63 24 3F 15 25 Open slow Chaser from color to 64 65 40 41 25 3 Open Color 1 Slow SOA KORE
56. pecified lamp types 7 Gently replace the lamp socket assembly in to place and secure with the four quick release fasteners 8 Be sure to reset the lamp running time in the TIME menu The lamp run time is designed to function as lamp replacement reminder see page 23 9 Final step would be to properly optimize the lamp Follow the steps below to properly align the lamp and inside the reflector Attention Be sure the lamp is securely seated in the lamp socket Failure to comply with this warning may cause excessive heat build up that may cause the internal lens to crack Lamp Optimization You should adjust the lamp position after each lamp replacement This is necessary due to the fact that every lamp has small manufacturing variations The Power Spot 700 includes a lamp optimization system consisting of two set screws on the back lamp socket cover set screw A and B The lamp adjustment is a matter of the users taste but will best be done as follows 1 Using a flathead screwdriver move the lamp position with setscrew B forwards and backwards until a very bright luminous spot hotspot can been seen clearly Elation Professionals Los Angeles Ca wwww ElationLighting com Page 48 Power Spot 700 IIT 2 Move lamp with setscrew A upward downwards until this hotspot is in the center of the beam projection 3 Use setscrew B once again to move the lamp forwards and backwards until you
57. r wheel 2 DU 99 99 Adjustment of the Gobo wheel 1 603e 99 99 Adjustment of the Gobo wheel 2 6033 99 99 Adjustment of the Gobo wheel 3 SHT 99 99 Adjustment Shutter Top side SH 99 99 Adjustment Shutter Bottom side PRIS 99 99 Adjustment of the Prism wheel IRIS 99 99 Adjustment of the Iris POFS 99 99 Adjustment of the Pan Offsets TOFS 99 99 Adjustment of the Tilt Offsets CLRE Adjustments in the internal circuit ARES 99 99 Adjust Reset wheels stand still after the reset VII 99 99 Software version of Tilt board VIR 99 99 Software version of Head board VIR 99 99 Software version of Base board VIR 99 99 Software version of board no 4 JUG 99 99 Function not yet available Elation Professionals Los Angeles Ca wwww ElationLighting com Page 31 Power Spot 700 IIT 8 9 9 Default Settings JFSE This function is used to restore all the factory default settings and presets Press the Enter button to confirm this operation or the Mode button to cancel and return to the menu When this operation is selected the LED will briefly readout ok then return to the previous function The chart below details the factory defaults Function Display Default Settings DMX Address 00 JOO Pan reve
58. rse RPRN on OFF Vv Tilt reverse RILT on OFF v Automatic lamp on LAAU on OFF wv Lamp on via DMX JLOF ON 7 OFF Display JISP DI e REV Cooling fan FARIS HIGH REG v LOOF LOHI Feedback FEED On v OFF 8 9 10 Feedback APC FEED The POWER SPOT 700 is equipped with APC automatic position correction This function automatically corrects the Pan and Tilt movement should the unit lose step or is obstructed and forced to lose step Press the Enter button to access the sub menu Use the Up and Down buttons to toggle between ON and OFF and confirm once more with the Enter button or use the Mode button to cancel the operation 8 9 11 Error and Fault Corrections EFLG These functions are reserved for authorized technicians only Elation Professionals Los Angeles Ca wwww ElationLighting com Page 32 Power Spot 700 IIT 8 10 Display Error and Information Messages HEAT This message appears if you try to switch on the lamp within 5 minutes after having switched off lamp too hot The message will appear on the display if the lamp doesn t ignite within 20 seconds The fixture will store this command and automatically ignite the lamp after 5 minutes IG E When igniting the lamp the electronic ballast will examine whether the lamp ignited or not If the lamp does not ignite within 20 seconds the igniting sequence is terminated
59. t 700 IIT Elation Professional 6122 S Eastern Ave Los Angeles Ca 90040 www ElationLighting com info QElationLighitng com Elation Professionals Los Angeles Ca wwww ElationLighting com Page 68
60. ta True signal Pin 3 Not Used Pin 4 Do Not Use Not Used X _ Pin 5 Do Not Use Fixture DMX addressing All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture responds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the head of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all you fixtures to the same Elation Professionals Los Angeles Ca wwww ElationLighting com Page 21 Power Spot 700 IIT DMX address will subsequently control all fixtures in the same fashion in other words changing the settings of one channel will affect all the fixtures simultaneously If you set each fixture to a different DMX address each unit will start to listen to the channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture In the case of the Power Spot 700 II which is a 21 channel fixture you should set the starting DMX address of the first unit
61. tely sure it has cooled Never look directly into the lamp beam You risk injury to your retina which may induce blindness Be sure to track and record the lamp running time The lamp should be changed at the end of the specified lamp life regardless of lamp output You may also have to change the lamp if it shows any deformations or damage The same is with all glass components color filters lenses and mirrors For safe operation follow the Installation guide described in chapter two of this manual Operating the POWER SPOT 700 II without suited safety aids such as safety cables or clamps can increase the risk of damage and or personal injury Installation should only be performed by qualified and certified personal When mounting this fixture use only the original rigging parts included with this fixture Any structural modification will void the original manufactures warranty and may increase the risk of damage and or personal injury 10 To reduce the risk of fire or shock do not expose this unit to rain or moisture 11 Do not attempt to operate this fixture if the power cord is frayed or damaged Elation Professionals Los Angeles Ca wwww ElationLighting com Page 8 Power Spot 700 IIT 3 FEATURES Pan 530 Tilt 280 3 operation mode DMX controlled stand alone or sound activated Electronic Power Supply Control board with 4 digit display Digital display can be turned 180 to fit different
62. terminals located on the fixtures most controllers will only have output jacks DMX Linking To ensure proper DMX data transmission always use proper DMX cables not microphone cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain The DMX address is set electronically using the controls on the LCD menu Data Cable DMX Cable Requirements For DMX and Master Slave Operation Your fixture and your DMX controller require a standard 3 pin or 5 pin XLR connector for data input and data output the figure on the next page is of a 3 Pin XLR connector If you are making your own cables be sure to use two conductor shielded DMX cable rated at 120 ohms this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers Keep in mind that although microphone cable may look similar to DMX cable it does not share the same resistance rating and may be susceptible to line interference Please always use proper DMX cables for your
63. thorized technician only This connector is used to upgrade the operating software and to test the fixture 12 3 PIN DMX Output Jack This 3 Pin XLR jack is used to send an outgoing DMX signal For best results this jack should be terminated if it is the last fixture in a DMX daisy chain see termination on page 14 13 3 PIN DMX Input Jack This 3 Pin XLR jack is used to receive an incoming DMX signal 14 Carrying Handle The fixtures includes two built in carrying handles Be sure to always handle the fixture by the built in carrying handles Never lift or carry the fixture by the head or retaining arms as this could cause serious damage to the fixture and void your manufactures warranty 15 Power Switch The switch is used to control main power to fixture s electronics 16 Lamp Fuse Holder This housing holds a 250v 10A GMA fuse 120v operation Never defeat this fuse This fuse is designed to protect the lamp in the event of severer power fluctuations In the event of fuse failure always be sure to replace this fuse with an exact match unless otherwise instructed by an authorized Elation technician Elation Professionals Los Angeles Ca wwww ElationLighting com Page 14 Power Spot 700 IIT 17 Internal Cooling Fan This fixture is equipped with two high velocity variable speed fans mounted in the base to aid in the cooling process These fans are designed to vary their velocity at different operating tempera
64. tion slow Each 4 sound impulse 255 FF 100 gt new prism 18 Iris Iris open closed 0 127 00 7F 00 49 Ascend with Shutter random 128 143 80 8F 50 56 Descend with Shutter random 144 159 90 9F 56 62 Ascend with Shutter audio 160 175 AO AF 63 68 Descend with Shutter audio 176 191 BO BF 69 74 Elation Professionals Los Angeles Ca wwww ElationLighting com Page 43 Power Spot 700 IIT Channel Function Time and Value DMX HEX Ascend with Shutter Slow fast 192 207 CO CF 75 81 Descend with Shutter Slow fast 208 223 DO DF 82 87 Pulse effect Slow fast 224 239 E0 EF 88 93 Ascend descend effect Slow fast 240 253 FO FD 94 99 Iris open 254 255 FE FF 100 19 Special No Function 0 15 00 0F 0 6 Gobo1 shake 10 3 5 moves min up to 16 31 10 1F 7 12 60 moves max slow fast Gobo1 shake 20 3 5 moves min up to 32 47 20 2F 13 18 60 moves max slow fast Gobo1 shake 30 3 5 moves min up to 48 63 30 3F 19 24 60 moves max slow fast No function 64 111 40 6F 23 43 Color1 Chaser C C 1 0 7 BPS 2 3 BPS 112 127 70 7F 44 50 slow fast gt 1 43 s 0 43 s Color1 Chaser C C 2 0 7 BPS 2 0 BPS 128 143 80 8F 51 56 slow fast gt 1 43 s 0 5s No function 144 175 90 AF 57 68 Audio Pan Tilt slow Each 4
65. tomatic detector for the optical effects module software version 1 28 and later It detects whether the Power Spot 700 is equipped with a standard Spot module YSDT or a CMY module YCMY In case the module is not correctly mounted or is in need of service the display will read MS E Module Error Elation Professionals Los Angeles Ca wwww ElationLighting com Page 33 Power Spot 700 IIT 9 OPERATION Operating Modes The Power Spot 700 II can operate in three different modes This next section will detail the differences in the operating modes e Stand alone mode The fixture will react to sound chasing through the built in programs e Master Slave mode You can daisy chain up to 16 fixtures together to get a synchronized light show without the need of an external controller The fixtures will react to sound chasing to synchronized light show DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the Elation Show Designer 2 9 1Universal DMX Control This function allows you to use a universal DMX 512 controller such as the Elation Show Designer 3 or Elation Show Designer 2CF to control head movement the color wheel the shutter strobe and all other DMX traits A DMX controller allows you to create unique programs tailored to your individual needs The Power Spot 700 II uses 21 DMX channels See page 37 for detailed
66. tures When the fixture reaches a predetermined internal operating temperature the fans function at high speeds The higher speeds provide better cooling associated with higher operating temperatures during long use When the fixture is operating at a lower temperature the fans operate at low speed Be sure to keep all vents clean blocked cooling vents can shorten lamp life and reduce the fixtures reliability For more information on the fan functions see page 30 section 8 10 7 18 Powercon Connector This power jack is only designed to be used with the Neutrik Powercon adapter included with your fixture This jack provides main power to your fixture 19 Electronics Fuse Holder This housing holds a 250v 2A GMA fuse 120v operation Never defeat this fuse this fuse is designed to protect the electronics in the event of severer power fluctuations In the event of fuse failure always be sure to replace this fuse with an exact match unless otherwise instructed by an authorized Elation technician 20 4 Segment Menu Display This display details menu functions 21 Mode Select Button This button is used to access the fixture s main system menu and on board programming functions 22 Enter Select Button This button is used to select and confirm a menu function when working in the fixture s operating system 23 Down Select Button This button is used to scroll backwards when navigating through the system menu 24 Up Select
67. ved DMX splitter such as the Elation Opto Branch 4 or DMX Branch 4 DMX 512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and Elation Professionals Los Angeles Ca wwww ElationLighting com Page 20 Power Spot 700 IIT DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a line terminator Elation part DMX T PACK will decrease the possibilities of erratic behavior l Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance A 120 Ohm 1 4 W between PIN 2 DMX mie and PIN 3 DMX of the last fixture 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The following chart details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data Compliment signal Da
68. ystem that allows a quick and efficient means to secure a clamp to the unit To attach a clamp to the unit attach a clamp that is rated to handle the weight of the unit to your omega clamp After a clamp has been attached to the omega clamp attach the cam locks to the designated position on the bottom of your unit Lock the cam locks into position by turning the wing nuts 90 See page 17 for proper clamp mounting and assembly Ethernet Jack This jack is used for arcnet DMX protocol Elation Professionals Los Angeles Ca wwww ElationLighting com Page 13 Power Spot 700 IIT 7 5 PIN DMX Output Jack CMY Version Only This 5 Pin XLR jack is used to send an outgoing DMX signal For best results this jack should be terminated if it is the last fixture in a DMX daisy chain see termination on page 20 8 5 Pin DMX Input Jack CMY Version Only This 5 Pin XLR jack is used to receive an incoming DMX signal 9 Microphone Sensitivity Adjustment Knob This knob is used to adjust the frequency sensitivity of the internal microphone when operating in audio mode When the knob is turned counter clockwise the unit is less sensitive to sound When the knob is turned clockwise the unit is more sensitive sound 10 Built In Microphone The built in microphone is used to pick up sound impulse that are used to chase the built in programs in Sound Active control 11 Firmware Connection This connector is for use by an au

Elation Professional 700 II Security Camera User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents