Home

Eicon Networks DM/V600A-2E1-PCI Network Card User Manual

1. on boards at each end of the CT Bus cable JP2A CT Bus termination jumper JP2B MVIP Bus termination jumper 8 P3 CT Bus connector 9 ISA Edge Retainer 10 Signal Processing Daughterboard Linux Systems In a Linux system you must set SW1 to a unique number for each installed board Use a non magnetic screwdriver to turn SW1 to one of 16 board ID settings 0 9 or A F After the hardware and the system software are installed refer to the proper configuration files to retrieve the assigned board instance ID number s For more information about Linux configuration files see the Dialogic System Software documentation Installing the Hardware 1 With your computer on the static safe work area switch off the power and disconnect all power cords from the electrical outlets 2 Remove the computer cover 3 Select an empty PCI expansion bus slot and remove the slot s retaining screw and access cover plate if applicable 4 If you are not installing your board in an ISA form factor PCI slot remove the ISA edge retainer 5 Using the slot s board guides insert the board s edge connector into the bus slot Press firmly until the board is securely seated in the slot Installing a PCI Board Computer Chassis 32 Bit PCI Slot 6 Replace and tighten the slot s retaining screw to secure the board firmly in the chassis if applicable 7 Connect external digital telephone cables to the RJ
2. 48C jacks on the board bracket The topmost RJ 48C jack is for trunk 1 and the second RJ 48C jack is for trunk 2 Pinouts for the RJ 48C Jacks on Bracket 1 2 3 4 5 6 r 8 Network Interface Cable Connector RCV_RING Pin 4 RCV_TIP CHASSIS GROUND XMIT_RING XMIT_TIP CHASSIS GROUND CHASSIS GROUND CHASSIS GROUND ONOOSAWN 8 Repeat steps 3 7 for each additional board you are installing 9 Use the CT Bus cable to connect the board s you are installing to other boards in the system To preserve the electrical integrity of the CT Bus use a CT Bus cable with the appropriate number of connectors drops It is recommended that no more than two connectors at either end of the cable be left unused 10 Your system may include both CT Bus and SCbus boards To connect both board types you must install a CT Bus SCbus Adapter on one of the CT Bus boards in a system See the CT Bus SCbus Adapter Quick Install Card for installation details about the Adapter and the bus cables Installing the CT Bus Cable Pin 1 Your CT Bus cable may have a different number of connectors drops 11 Install CT Bus Termination Jumpers only on boards located at each end of the CT Bus cable See the Physical Description section for jumper details 12 Replace the computer s cover when finished and reconnect the power cords 13 Turn the computer s power ON CAUTION If your BIOS is set to use Plug
3. Dialogic DM V600A 2E1 PCI Media Board Quick Install Card e e Part Number 64 0074 02 a fg C Copyright 2001 2007 Dialogic Corporation All rights reserved Before You Begin Protecting the Board from Damage CAUTION All computer boards are sensitive to electrostatic discharge ESD Handle all static sensitive boards and components at a static safe work area and observe anti static precautions at all times If you are not familiar with ESD safety precautions visit http Awww dialogic com support hwinstall to learn more Unpacking the Board Unpack the Dialogic DM V600A 2E1 PCI Media Board board according to the following steps 1 Prepare a static safeguarded work area 2 Carefully remove the board from the shipping carton and anti static packaging Handle the board by the edges and avoid touching the board s components 3 Lay the board on the static dissipative work surface Note Place boards in static shielding bags when carrying boards from station to station CAUTION Do not remove the board from the anti static packaging until you are ready to install it Observe proper anti static precautions at all times Physical Description CH4 CH3 CH2CH1 Configuring the Hardware Board Identification The device driver part of the system software assigns board instance numbers in ascending order beginning with 0 as it detects each board in your system A board
4. TSOEVER AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY Dialogic products are not intended for use in medical life saving life sustaining critical control or safety systems or in nuclear facility applications It is possible that the use or implementation of any one of the concepts applications or ideas described in this document in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other intellectual property rights owned by third parties Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic More detailed information about such intellectual property is available from Dialogic s legal department at 9800 Cavendish Blvd 5 Floor Montreal Quebec Canada H4M 2V9 Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement any concepts or applications and does not condone or encourage any intellectual property infringement and disclaims any responsibility relate
5. and Play technology and there are ISA boards in your system an IRQ conflict can be created if a PCI board is assigned the same IRQ as an ISA board This could cause the machine to stop responding You can prevent this by entering the BIOS and reserving the appropriate IRQs those used by your ISA boards for ISA use only After Installing the Hardware After installing the hardware run the Dialogic Configuration Manager DCM as described in the installation instructions included with the Dialogic System Software to configure your system For technical specifications and product information go to http www dialogic com products htm Warranty and Return Information Warranty Period For specific warranty information for this board refer to the Warranty section of the Products page located at this URL http www dialogic com warranties Contacting Technical Support Dialogic provides technical support for its products through a network of value added distributors who are trained to answer technical questions on installing and configuring Dialogic products If you are unsure how to contact your support channel please call Dialogic in the United States at 973 967 6600 9am 5pm EST and we will assist in obtaining the appropriate support channel Outside the United States please refer to http www dialogic com support contact Dialogic also provides direct support via Dialogic Pro Services agreements For more de
6. d thereto These intellectual property licenses may differ from country to country and it is the responsibility of those who develop the concepts or applications to be aware of and comply with different national license requirements Dialogic Diva Eicon Eicon Networks Eiconcard and S Pcontrol among others are either registered trademarks or trademarks of Dialogic Dialogic s trademarks may be used publicly only with permission from Dialogic Such permission may only be granted by Dialogic s legal department at 9800 Cavendish Blvd Sth Floor Montreal Quebec Canada H4M 2V9 Any authorized use of Dialogic s trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic s trademarks requires proper acknowledgement The names of actual companies and products mentioned herein are the trademarks of their respective owners
7. instance number is the identification ID number used by the system software to recognize the board Note f you add or remove a board the system may change the existing board instance numbers depending upon the PCI bus and slot number where the board is installed or removed Windows Systems Leave SW1 set to the factory default of 0 to let the system automatically assign board instance numbers by PCI bus slot number After the hardware and the system software are installed refer to the Dialogic Configuration Manager DCM utility to retrieve the assigned board instance ID number s For more information about board identification see the DCM online help RJ 48C jacks Connectors to external digital telephone network interface General Network Interface Alarm LED Power LED Reset LED SW1 Rotary switch to set board identification Linux systems only Alarm LEDs During power up indicate Power on Self Test POST status During operation CH1 and CH2 LEDs indicate network alarms for each trunk Red Alarm to indicate loss of signal Yellow Alarm to indicate loss of frame synchronization at far end of external network Green Indicates signal present powered up and receiving signal from external E1 sources Loopback Indicates loopback mode is activated CT Bus MVIP Bus Termination Jumpers Bus signal is terminated when the corresponding jumper clip is installed Note Signal must be terminated only
8. tails of direct support from Dialogic please refer to http www dialogic com support DialogicPro Returning a Product To return a board for warranty or any other returns please refer to the following http Awww dialogic com support hwfaults Sales Assistance If you have a sales question please contact your local Sales Representative or the Regional Sales Office for your area Address telephone and fax numbers are available at the Dialogic website located at http www dialogic com contact htm To purchase Dialogic products please refer to the following website to locate the appropriate supplier http www dialogic com purchase htm All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries Dialogic Reasonable effort is made to ensure the accuracy of the information contained in the document However Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors inaccuracies or omissions that may be contained in this document INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC DIALOGIC ASSUMES NO LIABILITY WHA

Eicon Networks DM/V600A-2E1-PCI Network Card User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents