DeLonghi PAC GSR/MU Air Conditioner User Manual
Contents
1. order The following precautions should be observed e Before passing the connector hose through the hole in the wall the threaded ends of the rapid couplings should be protected using insulating tape or similar e Fit the two upper refrigerant couplings to the two lower couplings and tighten by hand ensuring that they are correctly connected Then use the spanner to tighten fully e After connecting the two refrigerant couplings fasten the brackets e Check that the refrigerant couplings are sealed perfectly by wetting the couplings with a little soapy water No soap bubbles should form Attention Connection and disconnection of the refrigerant couplings should be carried out by qualified personnel INTERNAL UNIT The internal unit should be installed in the room to be conditioned Generally the ideal position for the internal unit is under a window In any case it should be positioned near an external wall The internal unit must be perfectly leveled If necessary use the castor stops supplied with the machine The air intake and outlet grilles should not be obstructed in any way EXTERNAL UNIT The external unit can be positioned on a terrace or balcony In this case it is not w p b p fi D necessary to use the fixing brackets The external unit can also be mounted on a wall In this case use the special wall mount brackets Alternatively for temporary installation the exte2. suitable for the power requirements of the unit the socket must be suitable for the plug if not have the socket replaced FINAL CHECK In order to ensure that your air conditioner operates with the maximum efficiency make sure that all doors and windows in the room to be air conditioned are closed except for temporary installation in which case a window must be left partially open Close the windows Draw the curtains and or partially close the blinds to protect the room against direct sunlight This will increase the efficiency and economy of the air conditioner Draw the curtains Do not place objects of any kind on the air conditioner Ensure that the air intake and discharge vents are not obstructed Make sure that there are no sources of heat in the room amp Close the door Do not cover YOUR AIR CONDITIONER IS NOW READY FOR USE CONTROL PANEL TIMER ON signal lamp Alarm warning light Fan signal lamp Air conditioning signal lamp 4 e Min air conditioning X MIN signal lamp 6 GER Max air X Xmax conditioning signal lamp C D Timer notches Thermostat knob ON OFF main switch key SETTING THE TIMER The programmer timer like all clocks must be set to the exact time If for example it is 4 0
3. 0 p m turn the dial in a clockwise direction following the direction of the arrow until the number 4 4 p m is lined up with the arrow pointer the arrows indicates 4 00 p m approximately DC arrow pointer N B Never turn the dial in an anti clockwise direction The timer is in effect an electric clock and works only if the plug is connected to the power supply Whenever the plug is disconnected or there is a power failure the programmer stops the clock is then slow and must be re set The unit can be used in either programmed or Fan speed selection key Fan conditioning selection key Timer key non programmed mode PROGRAMMED MODE 1 Release timer button B 2 Set the operating times by pushing out the notches on the dial corresponding to the period required each notch represents 15 mins 3 Check that the timer indicates the correct time see instructions on setting Operating time eg from 9 to 11 a m 4 Select the desired function as shown in the chart overleaf The unit will now switch on and off each day at the selected times N B To override the programmed operating times simply press the ON OFF timer key NON PROGRAMMED MODE 1 B TIMER button must be pressed 2 Select the desired function as shown in the chart on the following page HOW TO START UP THE CONDITIONER Plug the appliance into the wall socket The ON OFF sig
4. OWNERS MANUAL Pnoun AIR CONDITIONER PAC GSR MU DeLonghi IMPORTANT INFORMATION When using electrical appliances basic safety precautions should always be followed including the following Read all instructions To protect against fire electrical shock and personal injury do not immerse cord plug or appliance in water or other liquid Close supervision is necessary when any appliance is used by or near children Do not operate with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return the appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments or spare parts not recommended by the appliance manufacturer may result in fire electrical shock or personal injury Do not use outdoors Do not use the appliance for other than the intended use Do not place any strain on the power cord Avoid twisting and or tangling Ensure that outlet vent of exhaust hose is kept debris clear and obstruction free Ensure that ventilation holes on the rear of the machine and front louvers are not blocked The Pinguino should not be installed where the atmosphere could contain combustible gases Avoid using Pinguino in oily or sulphurous atmospheres or near sources of heat Before moving the air conditioner empty water from collection tray Do not place hot or heavy objects on the applianc
5. airs become necessary or spare parts are needed please write to SERVICE DE LONGHI AMERICA INC PH N 1 800 322 3848 Park 80 West Plaza One 4th floor 2000000000000000000000UUUUUUUUUOOOO SS A50000000000000000000000000000000 00000000000000000000000 CZD 00000000000000000000000 GARANTIE Nous garantissons que tous les appareils lectriques DE LONGHI sont exempts de tout d faut de mat riaux et de manufacture Notre obligation sous cette garantie est limit e au replacement ou a la r paration gratuit en notre usine de toutes les pieces d fectueuses autres que les pieces endommag es durant le transport qui nous seront retourn es transport pay d avance end ans un an apr s la livraison l acheteur utilisateur Cette garantie ne sera applicable que si l appareil a t utilis selon les instructions du fabriquant qui accompagnament l appareil et sur courant alternatif AC Cette garantie remplace toutes autres garanties et repr sentations exprim es ou impliqu es et toutes autres obligations ou responsabilit s de notre part Nous n authorisons aucune autre personne ou compagnie assumer pour nous une quelconque responsabilit en relation avec la vente ou l utilisation de nos appareils Cette garatie ne s appliquera ni aux appareils qui seront r par s ou endommag es hors de notre usine ni aux appareils qui auront t sujets une mauvaise utilisation une n gligence o un accident Si des r p
6. arations ou des pi ces de rechange sont n cessaires vous tes pri s d crire SERVICE DE LONGHI AMERICA INC PH N 1 800 322 3848 Park 80 West Plaza One 4th floor SADDLE BROOK NJ 07663 000000000000000000000000000000000000000000000000000000000000000S 1 00000000000000000000000000000000 E A DOO000000000000000000000000000000ES o
7. b kg 30 87 14 Average figures which may vary according to the ambient humidity and the temperature OPTIMUM OPERATING RANGE OUTSIDE TEMPERATURE 69 8 95F 21 35 C INSIDE TEMPERATURE 69 8 109 F 21 43 C ILLUSTRATED MAIN FEATURES LIST INTERNAL UNIT Connection hose Control panel cover Control panel Air vent control knob Air outlet grille Removable filter Air intake grille Rear panel Fuse Carrying handle Power cable Condensation discharge tube Castors ILLUSTRATED ACCESSORY LIST DESCRIPTION SUPPLIED Wall bracket 2 Screws wall plugs 6mm 4 Nut and bolt 5mm 4 Support belt with hook 2 Frame with connector hose 1 Castor stop 2 S Condensation drainage 1 e coupling INSTALLATION The appliance must be fitted at least 30 Models without special couplings cm from the surrounding walls The hose which connects the internal unit to the external unit can be positioned in two ways b Through a small hole 5 5 x 2 5 cm in the lower part of the door or window frame In this case it is necessary to use the special frame for the connection hose a Through a slightly open window or door frame for hose ADJUSTABLE WINDOW BRACKET Pinguino is equipped with an adjustable win
8. dow bracket If you have a sash window position the external unit outside the window place the bracket on the window sill extend the bracket fully within the window frame making the hose passing through the slot and lower the window onto the bracket Thanks to the wing nut it s possible to use the window bracket also for sliding windows MODELS WITH SPECIAL COUPLINGS If your air conditioner is fitted with the special rapid fit coupling the hose which connects the internal unit to the external unit can also be passed through a round hole in an external wall diameter 6 cm approx In this case it is necessary to disconnect the internal unit as follows 1 Remove the plug from the wall socket 2 Remove the rear panel on the back of the appliance by unscrewing the two retaining screws 3 Remove the metal brackets which fasten the hose to the appliance 4 Using a 24mm spanner unscrew the union on the coupling When doing this use a 19mm spanner to block the extremity of the hose in position Repeat this operation for the second union 5 Detach the condensation hose from its coupling 6 Disconnect the electrical connector socket by pressing the two retainer tabs The path of the connector hose should be as straight as possible without sharp curves or kinks To re connect the ends of the connector hose to the internal unit repeat steps 1 to 6 in reverse
9. e Clean air filter every week see instructions at page 13 Unplug from outlet when not in use and before cleaning To disconnect turn any controll to OFF then remove plug from wall outlet Important If you need to use an extension cord please be sure to use a heavy duty extension cord minimum 14 gauge SAVE THESE INSTRUCTIONS Dear user We thank you for purchasing the Pinguino air conditioner and congratulate you on your wise choice For optimal results please read this manual carefully before installing or operating We know that the Pinguino will maintain your environment pleasingly comfortable at all times With best wishes De Longhi S p A If you have any questions about the operation or service of your Pinguino please call our toll free service number 1 800 322 3848 or visit our internet site www delonghiusa com for general overlook of De Longhi group visit www delonghi com SPECIFICATIONS Power supply voltage V 110 120 Frequency Hz 60 Cooling capacity see rating label Current consumption see rating label Air flow capacity 520 m h Dehumidification capacity 1 81 h Length of hose feet m 11 3 3 Dimensions internal unit width in mm 18 03 458 height in mm 33 46 850 depth in mm 15 74 400 weight Ib kg 44 97 Dimensions external unit width in mm 17 71 450 height in mm 18 50 470 depth in mm 8 26 210 weight I
10. em persist contact Service Center turn knob anti clockwise remove obstacle contact Service Center switch off and contact Service Center close window remove heat source lower thermostat setting clean filter FOR UNITED STATES ONLY R100000000000000000000000 CEEP 00000000000000000000000 LIMITED WARRANTY We warrant each DE LONGHI AIR CONDITIONER to be free from defects in material and workmanship Our obligation under this warranty is to provide one year parts and labor free from purchase date with an additional four 4 years on any part of the sealed system consisting of the compressor evaporator condenser and factory connected refrigerant tubing This warranty shall apply only if the AIR CONDITIONER is used in accordance with the factory directions which accompany it and on Alternating Current AC circuit This warranty is in lieu of all other warranties and representations expressed or implied and all other obligations or liabilities on our part We do not authorize any other person or company to assume for us any liability in connection with the sale or use of our AIR CONDITIONER This warranty shall not apply to assume for us any liability in connection with the sale or use of our AIR CONDITIONER This warranty shall not apply to any AIR CONDITIONER which shall have been repaired or altered outside our factory nor shall it apply to any AIR CONDITIONER which has been subjected to misuse negligence or accidents If rep
11. ff this circuit prevents it from switching on again for at least 3 minutes MAINTENANCE PRECAUTIONS _ During cleaning and normal maintenance operations Under no circumstances should appliance be remember to disconnect plug washed with running water Damage could be caused to the electrical circuit CLEANING OF EXTERNAL HOUSING AN Never use petrol gas alcohol or solvents for lt cleaning Never spray insecticides or similar products on the appliance as these may Clean with a damp cloth and dry thoroughly with a clean dry cloth CONTROLS AT THE BEGINNING OF THE SEASON Carefully follow installation procedure Check for any defects in power cord and plug AIR FILTER CLEANING Maintenance of air filter A clogged air filter reduces the quantity of circulating air and the efficiency of the appliance It is therefore recommended to clean the filter at weekly intervals Remove dust with a vacuum cleaner If the filter is very dirty wash it in lukewarm water and rinse thoroughly Cleaning procedure Removal and replacement of air filter Gently pull filter upwards as shown in figure Push to replace To remove dust deposited on filter use a vacuum cleaner If it is very dirty soak in lukewarm water and rinse thoroughly The temperature of the water must be kept below 40 C 104F After washing leave filter to dry befo
12. nal lamp 1 comes on and stays on for as long as the appliance is SEET to the socket Y Select either Programmed or Non programmed mode see previous Select the fan speed required pressing Fan speed key D 6 AIR CONDITIONING VENTILATION Key C Ventilation Conditioning must be released Turn the thermostat to Max cold Press key A ON OFF Signal lamp 5 Conditioning and either 6 or 7 Min or Max fan speed will come on j Key C Ventilation Conditioning must be pressed _ The appliance comes on If not refer to pag 14 To switch off the appliance press key A ON OFF main switch N B the TIMER ON signal lamp will only come on with Programmed mode N B For technical reasons the temperature is not shown in degrees but is represented by two lines which vary in thickness according to the temperature It is advisable to begin by turning the thermostat to the maximum setting thick green line maximum cooling When the room temperature is comfortable turn the thermostat slowly away from the maximum heating or cooling position until the air conditioner switches off Leave the thermostat in this position The air conditioner is now programmed to maintain the exact temperature at all Times This appliance is fitted with a special safety circuit When the compressor switches o
13. re replacing END OF SEASON OPERATIONS 1 Disconnect the ON OFF switch removing the plug from the power socket 2 Remove the plug from the drainage tube and empty the water from the internal condensation tray 3 Clean the filter and dry it carefully before replacing 4 Cover the appliance with a plastic bag to protect it from dust TROUBLESHOOTING Most malfunctions are caused by a very minor and easily solved problem Before contacting your nearest authorized Service Center for assistance consult the troubleshooting chart below SYMPTOMS The Pinguino does not function The air conditioner functions for a brief period only The appliance switches on and off constantly The air conditioner functions but the room is not cooled CAUSE power failure the appliance is not plugged in the notches on TIMER dial have not been set switch is off the alarm warning light is on the safety float has been enabled because the collecting tray inside the unit is too full thermostat has been activated exhaust hose to outside blocked fan blocked window open source of heat in room heater lamp etc or room is overcrowded thermostat regulated too high air filter clogged the capacity of the conditioner is not adequate for the size of the room SOLUTION wait connect plug either push notches out or disable timer turn main switch on drain water using the drainage tube supplied see page 5 If probl
14. rnal unit can be hung as shown in the figure In this case use the special support belts supplied with the appliance The external unit can be installed above or at the same level as the internal unit provided that the difference in height between the two units does not exceed 1 5 m The intake and outlet vents must not be obstructed Leave a space of at least 6 cm between the rear of the unit and the wall CONDENSATION DRAINAGE The condensation which forms when the unit is used for air conditioning i e in summer evaporates from the external unit If the humidity is particularly high it may be necessary to fit the condensation discharge tube supplied with the machine In this case fit the hose to the coupling on the bottom section of the external unit remove the rubber cap from the coupling When specific applications require it the condensation drainage can be done directly from the discharge pipe on the back of the unit Should this happen water will be collected into a tank and automatically removed through a pump system Such a pump has to be installed separately and is available at any air conditioning contractors in your area Rubber cap Ring g Coupling ELECTRICAL CONNECTIONS Before plugging the unit into the power supply check the following the power supply voltage must be the same as the voltage shown on the rating plate the power socket and the voltage circuit must be
Download Pdf Manuals
Related Search