Crestron electronic DIN-8SW8 Switch User Manual
Contents
1.2. run The wire gauge and the Cresnet power usage of the run should be used in the following equation to calculate the cable length value on the equation s left side Cable Length Equation 40 000 wee L Length of run or chain in feet F L lt R 6 Ohms Crestron Certified Wire 0 75 MM 18 AWG R xP P Cresnet power usage of entire run or chain Make sure the cable length value is less than the value calculated on the right side of the equation For example a Cresnet run using 0 75 mm 18 AWG Crestron Certified Wire and drawing 20 watts should not have a length of run more than 101 meters 333 feet Cresnet HP cannot be used 24 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Strip and Tin Wire Add Hubs NOTE All Crestron certified Cresnet wiring must consist of two twisted pairs One twisted pair is the 24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor When daisy chaining Cresnet units strip the ends of the wires carefully to avoid nicking the conductors Twist together the ends of the wires that share a pin on the network connector and tin the twisted connection Apply solder only to the ends of the twisted wires Avoid tinning too far up the wires or the end becomes brittle Insert the tinned connection into the Cresnet connector and tighten the retaining screw Repe
3. eane aia tia tiuaciatancatdarmbectas meuiceneastieatted 18 WS plo adie SGU Pera vies cited cinicun sone chidiatae havin AA 19 Establishiie OmimmuniC aon eci a A 19 Prosrams and FIIN ane iscca chores weyisincsbedi E EAEE 20 Procrani e heck Sei E EA 20 Operasie o E E EE T A E EEO 21 Propilen SOLVING ena a N E A A 23 SPROUDICS OOH saia E T ES 23 Check NGtwOrk WINN ins aa etal ee ote eee eh eke 24 FRETCREN CS POCO UIC IS ere se tt tga aa NA 23 Per gun eyes a a a a eben i ae ida 23 F me Upda nere E a a 26 Retrnand Warranty PONCICS cnca end a E NS 21 Merchandise Returns Repair Service ccsssseesessseeeeeceeeceeeccecaaaeeeseseeeeseeeeeeeeaaas 21 CRESTRON Limited Warranty ornen ecrin onien E A E Et 21 Operations amp Installation Guide DOC 6666A Contents e i Crestron DIN 8SW8 DIN Rail High Voltage Switch Crestron Green Light DIN Rail High Voltage Switch DIN 8SW8 Introduction The DIN 8SW8 is an eight channel high voltage switching module designed to support switching of non dimmable lighting and fans A single model supports both 120 and 220 240 Volt applications Each channel handles incandescent loads up to 10 Amps fluorescent loads up to 5 Amps and also 1 2 HP motors May not be compatible with some high inrush current loads Features and Functions Eight channels of power switching Supports 120 240 Volt 50 60 Hz Override input Cresnet communications Setup via front panel or software Progr
4. information on the connections controls and indicators available on your DIN 8SW8 DIN 8SWS8 Physical View CRESTRON SETUP OVR PWR NET DIN 8Sws HIGH VOLTAGE SWITCHING 10A INC SA FLUOR MAX OUTPUT 240V MAX 50 60Hz NET _ OVERRIDE C 24 Y Z G re E E OVR G OVEKG DIN 8SW8 Overall Dimensions p a 22ain A A 90 mm q 7 3 55 in 94 2 mm as 3 71 in 59 5 mm AIT e en gt 6 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Connectors Controls amp Indicators CONNECTORS DESCRIPTION CONTROLS amp INDICATORS 1 8 and LEDs 8 Sets of 2 captive screw oo eo eo 20 22 20 2o loo ien k Isolated Class 1 SPST relay switch circuits 1 8 Relay rating 10 Amps incandescent 5 Amps fluorescent 16 Amps resistive 0 5 HP 120 240 Volts AC per channe Maximum wire size 2 5 mm 12 AWG 8 Red LEDs and 8 miniature pushbuttons for status indication and local control of each channel 2 2 4 pin 3 5 mm detachable e mY26 terminal blocks paralleled Cresnet slave port Connects to Cresnet control network Maximum wire size 1 5 mm 16 AWG Pin 1 24 Power 24 Volts DC Pin2 Y Data Pin3 Z Data Pin 4 G Ground 3 NET ID 2 7 Segment green LED
5. Crestron GeenLigt DINSSV B DIN Ral HgVoltage Switch Operations amp lnstallation Gide This document was prepared and written by the Technical Documentation department at T CRESTRON Crestron Electronics Inc 15 Volvo Drive Rockleigh NJ 07647 1 888 CRESTRON All brand names product names and trademarks are the property of their respective owners 2008 Crestron Electronics Inc Crestron DIN 8SW8 DIN Rail High Voltage Switch Contents Crestron Green Light DIN Rail High Voltage Switch DIN 8SW8 1 Odc NO o TAT T nana ciadaee NET NTA R l Features and PUNCUIONS siscsttencatepsaataiatdesya tage saraeatieawahapnscaantiow au E siete l APPICANONS seir n E O te eeet ce Teese Cnn ree ne Trent tet St ree 3 DCU WIC AUONS Aa tac a acer ctacet es E E N 4 Physical Descriptio esae tei ea tanec sale ce deca cerns N 6 INGUSt YY COMP HANCS senie ieee adaaate N 9 DG i D PEATAS REPEAT TLIETT E EIEREN E A AE E Aan acdameens oat E ATE T 10 ING CW OTK WITI S eee E E EE 10 KEAS E O a aae E 10 LEE COU tee AEE sa doce E A E AT E PERE E E EE E PEE E REET eee 11 Hardware HOOKUP Sesteccrrane nea E EE 13 Prooraminn e SOWAT cero e EE EE Et 15 Earliest Version Software Requirements for the PC sssnessessssssssssssseeerressssessssssssse 15 Programming with Crestron SystemBuilder cccccccccccccecceeeeesseesseeeeeeeeeeeeeeaas 15 PLOST amin WIAD PI Oera a E A 16 Programming wHtA SIMPE WindOWS cisean E 16 Example Prostran
6. Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch DIN 8SWS8 Specifications Continued SPECIFICATION DETAILS Enclosure Light gray polycarbonate housing with polycarbonate label overlay UL94 V 0 rated 35 mm DIN EN 60715 rail mount DIN 43880 form factor for enclosures with 45 mm front panel cutout occupies 9 DIN module spaces 162 mm Dimensions Height 94 2 mm 3 71 in Width 159 mm 6 26 in Depth 59 5 mm 2 35 in Weight 369 g 13 oz Available Accessories DIN BLOCK DIN Rail Cresnet Distribution Block DIN HUB DIN Rail Cresnet Distribution Hub DIN PWS50 DIN Rail 50 Watt Cresnet Power Supply 1 May not be compatible with some high inrush current loads 2 The latest software versions can be obtained from the Crestron website Refer to the NOTE following these footnotes 3 Crestron 2 Series control systems include the AV2 and PRO2 Consult the latest Crestron Product Catalog for a complete list of 2 Series control systems NOTE Crestron software and any files on the website are for authorized Crestron dealers and Crestron Authorized Independent Programmers CAIP only New users may be required to register to obtain access to certain areas of the site including the FTP site Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 5 DIN Rail High Voltage Switch Crestron DIN 8SW8 Physical Description This section provides
7. Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 23 DIN Rail High Voltage Switch Crestron DIN 8SW8 Check Network Wiring Use the Fight In order to ensure optimum performance over the full range of your Wire ve pe installation topology Crestron Certified Wire and only Crestron Certified Wire may be used Failure to do so may incur additional charges 1f support is required to identify performance deficiencies because of using improper wire Se CAUTION Use only Crestron power supplies for Crestron equipment Failure to do so could cause equipment damage or void the Crestron warranty CAUTION Provide sufficient power to the system Insufficient power can lead to unpredictable results or damage to the equipment Please use the Crestron Power Calculator to help calculate how much power is needed for the system www crestron com calculators When calculating the length of wire for a particular Cresnet run the wire gauge and the Cresnet power usage of each network unit to be connected must be taken into consideration Use Crestron Certified Wire only If Cresnet units are to be daisy chained on the run the Cresnet power usage of each network unit to be daisy chained must be added together to determine the Cresnet power usage of the entire chain If the unit is home run from a Crestron system power supply network port the Cresnet power usage of that unit is the Cresnet power usage of the entire
8. Version Software Requirements for the PC NOTE Crestron recommends that you use the latest software to take advantage of the most recently released features The latest software 1s available from the Crestron website Crestron has developed an assortment of Windows based software tools to develop a Cresnet system You can create a program to control the DIN 8SW8 using the Crestron programming tools Crestron SystemBuilder D3 Pro or SIMPL Windows Customers whose focus is on lighting systems may prefer to use the D3 Pro software since it is designed especially for creating lighting and environmental system control applications Customers already familiar with SIMPL Windows who are including a lighting system as part of an overall control system project may prefer to continue using SIMPL Windows For the minimum recommended software versions visit the Version Tracker page of the Crestron website www crestron com versiontracker Programming with Crestron SystemBuilder Crestron SystemBuiulder is the easiest method of programming but does not offer as much flexibility as SIMPL Windows For additional details download SystemBuilder from the Crestron website and examine the extensive help file Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 15 DIN Rail High Voltage Switch Crestron DIN 8SW8 Programming with D3 Pro Crestron s D3 Pro lighting software provides all the tools necessary to c
9. ammable functionality via DIN AP2 or other 2 Series control system 9M wide DIN rail mounting Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 1 DIN Rail High Voltage Switch Crestron DIN 8SW8 DIN Rail Installation The DIN 8SW 8 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure Wiring connections are made using screw terminals positioned along the top and bottom clearly accessible from the front for easy installation and servicing All setup controls and indicators are positioned on the center front panel When installed in an enclosure utilizing 45 mm cutouts the DIN 8SW8 s front panel stays accessible while the connections are concealed Cresnet The DIN 8SW8 communicates with a DIN AP2 2 Series Automation Processor or other Crestron 2 Series control system via the Cresnet control network A pair of Cresnet ports is provided on the DIN 8SW8 allowing for easy daisy chaining of several DIN Rail Series automation control modules Override Input An override input is provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset state States can be set and saved locally from the front panel or remotely via software 2 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Ap
10. at the procedure for the other three conductors Use of a Cresnet hub repeater DIN HUB is advised whenever the number of Cresnet devices on a network exceeds 20 or when the combined total length of Cresnet cable exceeds 914 meters 3000 feet Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website www crestron com manuals This link will provide a list of product manuals arranged in alphabetical order by model number List of Related Reference Documents DOCUMENT TITLE 2 Series Control Systems Reference Guide Further Inquiries If you cannot locate specific information or have questions after reviewing this guide please take advantage of Crestron s award winning customer service team by calling Crestron at 1 888 CRESTRON 1 888 273 7876 You can also log onto the online help section of the Crestron website www crestron com onlinehelp to ask questions about Crestron products First time users will need to establish a user account to fully benefit from all available features Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 25 DIN Rail High Voltage Switch Crestron DIN 8SW8 Future Updates As Crestron improves functions adds new features and extends the capabilities of the DIN 8SW8 additional information may be made available as manual updates These updates are solely electronic and serve as intermediary supp
11. can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 9 DIN Rail High Voltage Switch Crestron DIN 8SW8 Setup Network Wiring When wiring the Cresnet network consider the following e Use Crestron Certified Wire NOTE Cresnet HP cannot be used e Use Crestron power supplies for Crestron equipment e Provide sufficient power to the system CAUTION Insufficient power can lead to unpredictable results or damage to the equipment Please use the Crestron Power Calculator to help calculate how much power is needed for the system www crestron com calculators e Use of a Cresnet hub repeater DIN HUB is advised whenever the number of Cresnet devices on a network exceeds 20 or when the combined total length of Cresnet cable exceeds 914 meters 3000 feet For more details refer to Check Network Wiring which starts on page 24 Identity Code The Net ID of the DIN 8SW 8 has been factory set to 89 The Net IDs of multiple DIN 8SW8 devices in the sa
12. ctors for NET and OVERRIDE ports are provided with the unit 8 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Industry Compliance This unit has been manufactured to comply with UL s Standards for Safety in Canada and the United States Formal approval is pending As of the date of manufacture the DIN 8SW8 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling CE NOTE This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there 1s no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which
13. digits DISPLAY and CONTROL and 2 miniature pushbuttons for a setting Cresnet ID and indicating errors Continued on following page Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 7 DIN Rail High Voltage Switch Crestron DIN 8SW8 Connectors Controls amp Indicators Continued CONNECTORS DESCRIPTION CONTROLS amp INDICATORS SETUP LED and BUTTON OVERRIDE with LEDs and BUTTON po eel ae OVERRIDE A AND AVID OVR G 1 Red LED and 1 recessed miniature pushbutton for enabling setup mode and touch settable ID 2 2 pin 3 5 mm detachable terminal blocks paralleled Maximum wire size 1 5 mm 16 AWG Sensing input for external low voltage contact closure Activates Override mode when a closure is present Minimum closure rating 10 mA per module at 24 Volts 1 Red LED and 1 miniature pushbutton for enabling Override mode and saving override presets For more information refer to Operation which starts on page 21 1 Green LED illuminates when DC power is applied to the NET port 1 Yellow LED indicates communication with the control processor 1 Recessed miniature pushbutton resets internal processor Interface conne
14. es following repair of items under warranty shall be paid by CRESTRON shipping by standard ground carrier In the event repairs are found to be non warranty return freight costs shall be paid by the purchaser CRESTRON Limited Warranty CRESTRON ELECTRONICS Inc warrants its products to be free from manufacturing defects in materials and workmanship under normal use for a period of three 3 years from the date of purchase from CRESTRON with the following exceptions disk drives and any other moving or rotating mechanical parts pan tilt heads and power supplies are covered for a period of one 1 year touchscreen display and overlay components are covered for 90 days batteries and incandescent lamps are not covered This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON dealer Purchasers should inquire of the dealer regarding the nature and extent of the dealer s warranty if any CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended or if it has been subjected to misuse accidental damage modification or improper installation procedures Furthermore this warranty does not cover any product that has had the serial number altered defaced or removed This warranty shall be the sole and exclusive remedy to the original purchaser In no event shall CRESTRON be liable for incidental or consequential damages
15. following figure DIN 8SWS8 Device Settings Window Device Settings Crestron DIN 85W8 Cancel e The ID code specified in the SIMPL Windows program must match the Net ID of each unit Refer to Identity Code which starts on page 10 Program Manager is the view where programmers program a Crestron control system by assigning signals to symbols The symbol can be viewed by double clicking on the icon or dragging it into Detail View Each signal in the symbol is described in the SIMPL Windows help file F1 Example Program An example program for the DIN 8SW8 is available from the Crestron website www crestron com exampleprograms 18 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features However before attempting to upload or upgrade it is necessary to establish communication Once communication has been established files for example programs or firmware can be transferred to the control system and or device Finally program checks can be performed such as changing the device ID or creating an IP table to ensure proper functioning Establishing Communication Use Crestron Toolbox for communicating with the DIN 8SW8 refer to
16. g of the DIN 8SW8 may be fed from a separate circuit breaker When making network connections to the DIN 8SW8 use a Crestron power supply Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 13 DIN Rail High Voltage Switch Crestron DIN 8SW8 Hardware Connections for the DIN 8SW8 1 8 CONNECTIONS FOR CONTROLLED DEVICES NET OVERRIDE TO CONTROL SYSTEM AND FROM DEVICE PROVIDING OTHER CRESNET DEVICES OVERRIDE SIGNAL amp TO OTHER DEVICES RECEIVING OVERRIDE SIGNAL With the circuit breaker turned off connect the wires to the terminal blocks per the markings provided on the DIN 8SW8 Load Connection Example for the DIN 8SW8 NEUTRAL 120 240 VOLTS 120 240 VOLTS FROM BREAKER LINE LOAD 14 o DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Programming Software Have a question or comment about Crestron software Answers to frequently asked questions FAQs can be viewed in the Online Help section of the Crestron website To post a question or view questions you have submitted to Crestron s True Blue Support log in at http support crestron com First time users will need to establish a user account Earliest
17. he Device Library and drop it in the System Views 16 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Locating the DIN 8SW8 in the Device Library fy Crestron Devices DvcLib 557 Control Systems 9 Cresnet Control Modules ae Lighting 3y CLS C yICL5 C6M _ 9 Lighting CL Series Lighting DIN Fail Series 3S DIN 1DIMU4 3 BIN 2Mcz 3 DIN 4DIMFLY4 37 DIN 65W5 YP DIN A08 i DIN IQ8 r _ Wireless Receivers Wireless Remotes _ User Devices e The system tree of the control system displays the device in the appropriate slot with a default Net ID as shown in the following illustration C2Net Device Slot 5 84 DIN AP2 HB Slot 1 C2I AP2 COM2 232 B Slot 2 C21 4P2 1R4 HB Slot 3 C2I AP2 108 HB Slot 4 C21 4P2 R 4 Slot 5 C2Net Device ID03 EMPTY ID 04 EMPTY ID 05 EMPTY r 49 ID 89 DIN 55W8 ID 8A EMPTY ID 86 EMPTY a BE Slot 6 C21 4P2ENET 1 EE Slot 7 C21 4P2 FRONTPANEL e Additional DIN 8SW8 devices are assigned different Net ID numbers as they are added Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 17 DIN Rail High Voltage Switch Crestron DIN 8SW8 Program Manager e If necessary double click a device to open the Device Settings window and change the Net ID as shown in the
18. lements prior to the release of a complete technical documentation revision Check the Crestron website periodically for manual update availability and its relevance Updates are identified as an Addendum in the Download column 26 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Return and Warranty Policies Merchandise Returns Repair Service 1 No merchandise may be returned for credit exchange or service without prior authorization from CRESTRON To obtain warranty service for CRESTRON products contact an authorized CRESTRON dealer Only authorized CRESTRON dealers may contact the factory and request an RMA Return Merchandise Authorization number Enclose a note specifying the nature of the problem name and phone number of contact person RMA number and return address 2 Products may be returned for credit exchange or service with a CRESTRON Return Merchandise Authorization RMA number Authorized returns must be shipped freight prepaid to CRESTRON 6 Volvo Drive Rockleigh N J or its authorized subsidiaries with RMA number clearly marked on the outside of all cartons Shipments arriving freight collect or without an RMA number shall be subject to refusal CRESTRON reserves the right in its sole and absolute discretion to charge a 15 restocking fee plus shipping costs on any products returned with an RMA 3 Return freight charg
19. me system must be unique Net IDs are changed from a personal computer PC via Crestron Toolbox refer to Establishing Communication on page 19 To set the Net ID using the front panel e Press the SETUP button to enter the Setup mode The SETUP LED illuminates e Press the left button under the NET ID display to change the most significant digit of the Net ID or press the right button under the NET ID display to change the least significant digit of the Net ID number 10 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch e When the desired Net ID is displayed press the SETUP button to exit the Setup mode The SETUP LED extinguishes NOTE If an invalid Net ID is set 00 02 FF Er will be displayed on the NET ID display The DIN 8SW8 will revert to the previously set Net ID NOTE The DIN 8SW8 will leave the Setup mode after 10 seconds of inactivity The DIN 8SW8 will revert to the previously set Net ID NOTE A small label with numbers and letters is provided on the front panel of the DIN 8SW8 to document the unit s Net ID in the case where power is not available Apply a mark over the digits that correspond to the assigned Net ID NET ID Label 3C Shown NETID 012349 6789ABCDEF 0723456789ABCDEF OOOMQOOO0OOQU000000 OOOOOODOOUODOD0OO4OOD When setting the Net ID consider the following e The Net ID of each uni
20. of the DIN 8SW8 away from the DIN rail NOTE Certain third party DIN cabinets provide space for an informational label between each DIN rail row Crestron s Engraver software version 4 0 or later can generate appropriate labels for all Crestron DIN rail products 12 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Hardware Hookup Make the necessary connections as called out in the illustration that follows this paragraph Refer to Network Wiring on page 10 before attaching the 4 position terminal block connector Apply power after all connections have been made WARNING Prior to connecting the device turn off power at the circuit breaker Failure to do so may result in serious personal injury or damage to the device Restore power after all connections have been made CAUTION Connecting this device to the wrong type of load or short circuiting the load can cause severe product damage Each load should be tested to identify a short circuit condition prior to wiring the load to the module NOTE Install in accordance with all local and national electric codes NOTE High voltage connections accept 2 5 mm 12 AWG wire Wire should be stripped to 8 mm 1 3 inch Tighten terminal blocks to 0 5 Nm 5 in lbs NOTE Use copper wire only For high voltage connections use wire rated for at least 75 C 167 F NOTE Each switch le
21. of any kind property or economic damages inclusive arising from the sale or use of this equipment CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party CRESTRON shall at its option repair or replace any product found defective without charge for parts or labor Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty Except as expressly set forth in this warranty CRESTRON makes no other warranties expressed or implied nor authorizes any other party to offer any warranty including any implied warranties of merchantability or fitness for a particular purpose Any implied warranties that may be imposed by law are limited to the terms of this limited warranty This warranty statement supersedes all previous warranties Trademark Information All brand names product names and trademarks are the sole property of their respective owners Windows is a registered trademark of Microsoft Corporation Windows95 98 Me XP Vista and WindowsNT 2000 are trademarks of Microsoft Corporation Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 27 T CRESTRON Crestron Electronics Inc Operations amp Installation Guide DOC 6666A 15 Volvo Drive Rockleigh NJ 07647 2020748 Tel 888 CRESTRON 05 08 Fax 201 767 7576 Specifications subject to www crestron com change without notice
22. on is released NOTE The control system program may change the settings if the Override mode is not enabled ee ide The Override mode overrides the control system program and sets all of the output states to the stored override values For instructions on saving override settings refer to Save Override Settings on page 22 To enable Override mode press and release the OVR button The OVR LED flashes slowly NOTE Ifthe Override mode was enabled from an external device i e a contact closure is present on the OVERRIDE terminals the OVR LED will flash quickly Pressing the OVR button has no effect To disable Override mode press the OVR button again The OVR LED extinguishes and the outputs return to the states set by the control system program NOTE If override states have not been stored the factory default override state is all loads on Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 21 DIN Rail High Voltage Switch Crestron DIN 8SW8 eave The state of each output can be saved as an override setting which can be Override Settings automatically recalled when the Override mode is enabled NOTE The control system program has a setting that can prevent locally saving the override state If this setting is enabled the display shows Er when trying to save override states For more information refer to the SIMPL Windows help file To save the state of an output a
23. plications The following diagram shows a DIN 8SW 8 in a typical application DIN 8SW8 in a Typical Application gy 2 LIGHTING gy UGHTING 2 git oy 2 LIGHTING i p LIGHTING 4 07 atin y g LIGHTING 0 LIGHTING a UGHTING g Ee gl aak SYSTEM MODULES SYSTEM MODULES OVERRIDE SWITCH Eeo Pal k f A d A Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 3 DIN Rail High Voltage Switch Crestron DIN 8SW8 Specifications Specifications for the DIN 8SW8 are listed in the following table DIN 8SWS8 Specifications SPECIFICATION DETAILS Load Ratings Switch Channels 8 Maximum Per Channel 10 Amps incandescent 5 Amps fluorescent 0 5 HP 120 240 Volts AC 50 60 Hz 5 Amps 30 Volts DC Minimum Per Channel 0 05 Amps 12 Volts DC Module Total 80 Amps incandescent 40 Amps fluorescent 120 240 Volts AC 50 60 Hz Load Types Incandescent magnetic low voltage electronic low voltage neon cold cathode fluorescent motors Power Requirements Cresnet Power Usage 5 4 Watts 225 mA 24 Volts DC Default Net ID 89 Minimum 2 Series Version 4 000 0226 or later Control System Update File Environmental Temperature 0 to 40 C 32 to 104 F Humidity 10 to 90 RH non condensing Heat Dissipation 18 BTU Hr Continued on following page 4 e DIN Rail High Voltage Switch DIN 8SW8
24. reate a complete Crestron lighting system for residential applications The lighting system includes the control system logic program touchpanel projects and keypad programming documentation and real time lighting adjustment capabilities As with all Crestron software D3 Pro provides extensive right click and drag and drop functionality in addition to convenient keyboard shortcuts for frequently used functions and commands Programming is organized into six system Views of the lighting system each providing a moveable toolbox of devices such as interfaces fixtures and control modules You can add a device to your system simply by selecting it from one of the toolboxes and dragging it to a room The available toolboxes differ depending on the View but all Views include a General toolbox that allows you to add areas and rooms at any time Programming with SIMPL Windows NOTE While SIMPL Windows can be used to program the DIN 8SW8 it is recommended to use SystemBuilder for configuring a system SIMPL Windows is Crestron s premier software for programming Crestron control systems It is organized into two separate but equally important Managers Configuration Configuration Manager is the view where programmers build a Manager Crestron control system by selecting hardware from the Device Library e To incorporate the DIM 8SW68into the system drag the DIN 8SW8 from the Lighting Lighting Din Rail Series folder of t
25. s an override setting press and hold the OVR button for three seconds The OVR LED blinks to indicate the new override setting has been stored Reset To reboot the DIN 8SW8 press the RESET button The outputs will be set to the states currently specified by the control system program If the control system does not provide any values the outputs will be set to the previously set values 22 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations If further assistance is required please contact a Crestron customer service representative DIN 8SWS8 Troubleshooting TROUBLE POSSIBLE CORRECTIVE CAUSE S ACTION Device does not DIN 8SW8 is not Verify the function receiving power DIN 8SW8 is connected to a Crestron power supply Device is not Use a Crestron power receiving power source Verify from a Crestron connections power source Device is not Use the Crestron receiving Power Calculator to sufficient power help calculate how much power is needed for the system Electrostatic Check that all ground discharge due to connections have improper been made properly grounding Unit ignores Unit is in Override Take out of Override Cresnet mode mode by pressing commands OVR button or releasing override contact closure
26. t must match an ID code specified in the SIMPL Windows program e Each network device must have a unique Net ID For more details refer to the Crestron Toolbox help file Installation The DIN 8SW8 must be installed by a licensed electrician in accordance with all national and local codes CAUTION This equipment is for indoor use only Mount in a well ventilated area The ambient temperature must be 0 to 40 C 32 to 104 F The relative humidity must be 10 90 non condensing NOTE When installing in an enclosure high voltage devices should be grouped separately from low voltage devices Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 11 DIN Rail High Voltage Switch Crestron DIN 8SW8 The DIN 8SW8 is designed for installation on a DIN rail Refer to the following diagram when installing Installing the DIN 8SW8 a g M DIN 8SW8 TOP DIN RAIL NOT SUPPLIED 1 Place the top of the DIN 8SW8 s rail mount over the top of the DIN rail 2 Tilt the bottom of the DIN 8SW8 toward the DIN rail until it snaps into place NOTE When mounting DIN rail products it may be necessary to use a flat head screwdriver to pull the DIN rail release tab while snapping the device onto the DIN rail To remove the DIN 8SW8 from the DIN rail use a small flat object 1 e a flat head screwdriver to pull the DIN rail release and tilt the bottom
27. the Crestron Toolbox help file for details There is a single method of communication indirect communication Indirect Communication PC RUNNING CONTROL SYSTEM DIN 8SW8 CRESTRON TOOLBOX SERIAL ETHERNET CRESNET OR USB e DIN 8SW8 connects to control system via Cresnet e Establish communication between the PC and the control system as described in the latest version of the 2 Series Control Systems Reference Guide Doc 6256 which is available from the Crestron website www crestron com manuals e Use the Address Book in Crestron Toolbox to create an entry for the DIN 8SW8 using the expected communication protocol Indirect Select the Cresnet ID of the DIN 8SW8 and the address book entry of the control system that 1s connected to the DIN 8SW8 e Display the DIN 8SW8 s System Info window click the i icon communications are confirmed when the device information is displayed Operations amp Installation Guide DOC 6666A DIN Rail High Voltage Switch DIN 8SW8 e 19 DIN Rail High Voltage Switch Crestron DIN 8SW8 SIMPL Windows Firmware Programs and Firmware Program or firmware files may be distributed from programmers to installers or from Crestron to dealers Firmware upgrades are available from the Crestron website as new features are developed after product releases One has the option to upload programs via the programming software or to upload and upgrade via the Crestron Toolbox For details on
28. uploading and upgrading refer to the SIMPL Windows help file or the Crestron Toolbox help file If a SIMPL Windows program is provided it can be uploaded to the control system using SIMPL Windows or Crestron Toolbox Check the Crestron website to find the latest firmware New users may be required to register to obtain access to certain areas of the site including the FTP site Upgrade DIN 8SW8 firmware via Crestron Toolbox e Establish communication with the DIN 8SW8 and display the System Info window e Select Functions Firmware to upgrade the DIN 8SW8 firmware Program Checks Using Crestron Toolbox display the network device tree Tools Network Device Tree to show all network devices connected to the control system Right click on the DIN 8SW8 to display actions that can be performed on the DIN 8SW8 20 e DIN Rail High Voltage Switch DIN 8SW8 Operations amp Installation Guide DOC 6666A Crestron DIN 8SW8 DIN Rail High Voltage Switch Operation NET ID Use the NET ID buttons to change the Net ID of the DIN 8SW8 For information on Net ID refer to Identity Code which starts on page 10 ad ey The state of each output can be manually controlled from the front panel To toggle the output between off and on tap the appropriate button 1 8 The corresponding LED illuminates and the output state is shown on the NET ID display oF for off On for on for two seconds after the butt
Download Pdf Manuals
Related Search