Craftsman 79938 Blower User Manual
Contents
1. Assembly instructions for using your unit as a blower is explained in the previous section WARNING Stop the unit and dis connect from the power source before opening the inlet cover or attempting to insert or remove the inlet restrictor or vacuum tubes The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades NOTE If you have already assembled your unit for use as a blower remove the biower tube and nozzle REMOVE THE INLET RESTRICTOR An inkt restrictor is used when using your unit as a blower This restrictor is not used during vacuum use and must be removed during assembly for vacu um use NOTE Be sure to keep the inlet re strictor for using your unit as a blower Open the inlet cover by inserting the tip of a screwdriver into the inlet cover latch area and twisting the screwdriver while pulling the inlet cover open Turn the inlet restrictor counterclock wise and remove it from the unit Do not close the inlet door You wiil next attach the vacuum tubes ATTACHING THE VACUUM TUBES There are 2 vacuum tubes an upper and lower tube The upper tube is cut straight on both ends and attaches to the blower unit The second tube is cut an at angle on the lower end This angled end will point toward the ground during vacuum use Locate the arrows on the upper vac uum tube and on the vacuum inlet area of the unit Upper Vacuum Tube2. the unit will not oper ate properly NOTE The strap is designed to position the collection bag on your shoulder with out kinks The strap is not intended to support the weight of the unit Shoulder strap on left shoulder No kinks in bag Allows free air flow HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE e Stop unit and unplug the extension cord Remove the vacuum tubes and collection bag e Install the inlet restrictor that was re moved when assembling for vacuum use NOTE If you are unable to locate the inlet restrictor the unit will still operate This restrictor improves the blower function e Close the inlet cover and make sure itis latched closed Re install the blower tubes Refer to the section ATTACHING THE BLOWER TUBE AND NOZZLE for instructions on how to attach these items EXTENSION CORD Use only a 120 A C voltage supply as shown on nameplate of the unit to power your edger The extension cord used to reach the power source must be Specifically marked as suitable for outdoor use The cord must be marked with the suffix W A Heavy enough to carry current from the power source the full length of extension cord to the unit Otherwise loss of power and overheating can occur causing damage to unit Refer to chart for minimum wire gauge rec ommendations The cord must be marked with the proper wire gauge Appropriate extension cords are available Do not
3. w While holding the intet cover open align the arrows and insert the vacu um tube into the opening Twist the tube clockwise until it is seated A second arrow on the vacuum tube will align with the arrow on the unit once the tube twisted completely in place f 4 Align arrows on tube amp unit Attach the lower vacuum tube to the upper vacuum tube by aligning the arrows on the two tubes Press the tubes together until the lower tube fs fully seated in the upper tube About 3 inches Upper Tube Lower Tube ATTACH THE COLLECTION BAG Slide the opening of the collection bag over the blower outlet Pull the strap with velcro tightly through the buckle and secure with velcro tabs NOTE Make sure the strap with velcro is located on the blower outlet as shown Also make sure the Zipper on the bag is completely closed Strap with Velcro Collection Bag e Blower Outlet ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG e Carefully loop the shoulder strap through the buckle as shown in the illustration below Last In First In Position the unit on your right hand side blower outlet and bag pointing toward the rear Hold the unit in an upright position and support the low er vacuum tube on the ground e Place the shoulder strap over your head and onto your left shoulder Adjust the strap to allow a free flow of air from the blower If the collection bag is kinked
4. THE COLLECTION BAG MUST BE PROPERLY EMPTIED You must properly empty and main tain the collection bag to avoid dete rioration and obstruction of air flow Remove the collection bag from the unit and empty after each use Do not store bag containing leaves grass etc Wash the bag once a year Remove the bag from the blower and turn the bag inside out Wash the bag witha water hose Allow the bag to hang and dry before you reuse the bag Vacuum Operating Position MAINTENANCE CUSTOMER RESPONSIBILITIES CARE amp MAINTENANCE TASK Check for Loose fasteners and parts Check for damaged or worn parts Clean unit and labels GENERAL RECOMMENDATIONS The warranty on this unit does not cov er items that have been subjected to operator abuse or negligence To re ceive full value from the warranty the operator must maintain unit as instruct ed in this manual Various adjustments will need to be made periodically to properly maintain your unit BEFORE EACH USE CHECK FOR LOOSE FASTENERS AND PARTS Inlet Cover Blower Tube Nozzle Vacuum Tubes Collection Bag CHECK FOR DAMAGED OR WORN PARTS Refer replacement of damaged worn parts to your Sears Service Center ON OFF Switch Ensure switch func tions properly by moving the switch to the Off position Make sure motor stops then restart motor and contin ue AFTER EACH USE CLEAN UNIT amp LABELS Clean the unit using a damp
5. the eyes and face which can result in blindness or serious injury USING YOUR UNIT AS A BLOWER Use your unit as a blower for e Sweeping debris or grass clippings from driveways sidewalks patios etc e Blowing grass clippings straw or leaves into piles or removing debris from corners around joints or be tween bricks Direct air flow by directing the nozzle down or to one side Always work away from solid objects such as walks large stones vehicles and fences Clean corners by starting in comers and moving outward This will help prevent an accumulation of debris which could fly into your face Be careful when working near plants The force of the air could damage tender plants Blower Operating Position USING YOUR UNIT AS A VACUUM Use your unit as a vacuum to pick up dry material such as leaves grass smali twigs and bits of paper For best results during vacuum use operate your unit at high speed e Move slowly back and forth over the material as you vacuum Avoid forc ing the unit into a pile of debris as this can clog the unit Keep the vacuum tube about an inch above the ground for best results NOTE If the unit becomes clogged stop the unit and disconnect the exten sion cord Wait until the impeller has completely stopped turning then re move the vacuum tubes Carefully reach into the vacuum opening and clear out the clogged debris CLEANING THE COLLECTION BAG IMPORTANT
6. the other This plug will fit only one way in a polarized outlet of the extension cord Ensure you have a polarized extension cord The plug of the polarized extension cord will fit into the outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a quali fied electrician to install proper outlet Do not change the plug in any way Inspect the insulation and connectors on the unit and extension cord before each use If there is any damage do not use until damage is repaired by your Sears Service Center Do not pull or carry by cord do not use cord as a handle close a door on cord or pull cord around sharp edges or cor ners Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord To reduce the possibility of the exten sion cord disconnecting from the unit during operation tie cord to cord re tainer and connect to recessed plug as shown in this manual Don t use the unit ifthe switch does not turn the unit on and off properly Have the unit repaired by your Sears Ser vice Center Keep the extension cord clear of oper ator and obstacles at ail times Do not expose cords to heat oil water or sharp edges Avoid any body contact with any grounded conductor such as metal fences or pipes to avoid the possibil ity of electric shock Don t handie plug or unit with wet hands Donotuse with damag
7. use multiple cords In good condition Cord insulation must be intact with no cracks or deterioration Plug connectors must be undamaged MINIMUM WIRE GAUGE RECOMMENDATIONS 120 16 16 14 AWG AW G AW G American Wire Gauge Secure the extension cord to the unit by tying the cord onto the cord retainer In sert the cord receptacle in to the re cessed plug OPERATION KNOW YOUR ELECTRIC BLOWER READ THIS OPERATOR S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustrations to your unit to familiarize yourself with the location of the various controls and adjustments Save this manual for future reference Top Handle Rear Handie Cord Retainer a DNS Inlet Cover Latch Upper Vacuum Tube Nozzle Lower Vacuum Tube The ON OFF SWITCH is used to acti vate the motor The INLET COVER LATCH is used to open and close the inlet cover The NOZZLE is designed to direct the flow of air OPERATING INSTRUCTIONS STOPPING YOUR UNIT Slide the ON OFF switch to the OFF position STARTING YOUR UNIT Your unit has two run positions LOW and HIGH Slide the switch to one of these positions to turn on the unit WARNING Do not use the unit without the blower tubes or collection bag propery attached to avoid flying debris and or impeller contact which can cause serious injury Always wear eye protection to prevent rocks or de bris from being blown or ricocheting into
8. Operator s Manual CRAFTSMAN 12 AMP Motor 195 MPH 405 CFM ELECTRIC BLOWER VACUUM Mode No 358 799380 FOR HOUSEHOLD USE WARNING A Read and follow all Safety Rules and Operating Instructions before first use of this product For answers to your questions about this product call 7am 7pm Mon Sat or 10am 7pm Sun a 1 800 235 5878 Hors isted are Central Time Sears Roebuck and Co Hoffman Estates IL 60179 USA 530087635 10 2629 AISWSASSV ALSAVS NOILVuHAadO TONVdS3 JONVNALNIVA TABLE OF CONTENTS Warranty Statement 2 Storage 10 posi rae Troubleshooting Chart 10 ssembly Operation 8 Parts Available 10 Maintenance 9 Spanish 11 Service amp Adjustments 10 Parts Ordering Back Cover WARRANTY STATEMENT FULL ONE YEAR WARRANTY ON SEARS CRAFTSMAN ELECTRIC BLOWER If this Craftsman Electric Blower fails to perform properly due to a defect in materi al or workmanship within 1 one year from the date of purchase Sears will repair or replace it free of charge WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN ELECTRIC BLOWER TO THE NEAREST SEARS STORE IN THE UNITED STATES This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Roebuck and Co D 817WA Hoffman Estates IL 60179 SAFETY RULES IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS AWARNING wren using electric gardening appliances basic safety precautions should always be
9. cloth with a mild detergent Wipe off unit with a clean dry cloth YEARLY CLEAN COLLECTION BAG Remove the bag and empty after each use Do not store bag without emptying the bag of all contents Wash the bag once a year by tuming inside out and washing with a water hose Be sure to let bag dry com pletely before re using the unit 9 SERVICE AND ADJUSTMENTS HOW TO REMOVE AN OBJECT FROM THE AIR INTAKE NOTE If the unit becomes clogged or an object is drawn into the air intake stop the unit and disconnect the exten sion cord Wait until the impeller has completely stopped turning then re move the vacuum tubes Carefully reach into the vacuum opening and clear out the air intake area Inspect the impeller for cracks If cracked or damaged do not use the unit have parts replaced by your Sears Service Center Do not attempt to replace them yourself PARTS AVAILABLE Blower Tube 534352705 Vacuum Tube Set 530402499 Inlet Restrictor 530402045 NOZZI enon ene nes 530402461 Collection Bag 530402533 Gutter KIU re eiad 71 79997 Safety Glasses 71 85707 Extension Cord 71 5702 STORAGE Prepare unit for storage at the end of the season or if it will not be used for 30 days or more WARNING Secure the unit before storing or transporting e Store unit with all guards in place Position unit so that any sharp object cannot accidentally cause inju
10. ed cord or plug If unit is not working as it should has been dropped damaged left out doors or dropped into water return it to your Sears Service Center for re air Ground Fault Circuit Interrupter GFCI protection should be provided on the circuit or outlet to be used for this unit Receptacles are available having built in GFCI protection and may be used for this measure of safe ty Keep others including children ani mals bystanders and helpers a mini mum of 30 feet 10 meters away Stop the motor immediately if you are ap proached Do not allow the unit to be used as a toy DOUBLE INSULATION CONSTRUCTION This unit is Double Insulated to help protect against electric shock Double insulation construction consists of two separate layers of electrical insula tion instead of grounding Tools and ap pliances built with a double insulation system are not intended to be grounded No grounding means is pro vided on this unit nor should a means of grounding be added to this unit As a resuk the extension cord used with your unit can be plugged into any stan dard 120 volt electrical outlet Safety precautions must be observed when operating any electrical tool The double insulation system only provides added protection against injury resuit ing from an internal electrical insulation failure All electrical repairs to this unit includ ing housing switch motor etc must be diagnosed and repaired by qualif
11. followed to reduce the risk of fire electric shock and serious injury WARNING The warnings and safety instructions in this manual must be followed to reduce the risk of fire electric shock or injury and to provide reasonable safety and efficiency in us ing this unit The operator is responsible tor following the warnings and instruc tions in this manual and on the unit Read the entire Operators Manual be fore assembling and using the unit Re strict the use of this unit to persons who read understand and follow the warn ings and instructions in this manual and on the unit Never allow children to use this unit Close attention is necessary when used near children OPERATOR SAFETY Always wear safety glasses or similar eye protection when operating servic ing or performing maintenance on your unit Wearing eye protection can help to prevent rocks or debris from being blown or ricocheting into eyes and face which can result in blindness or serious injury Always wear a respirator or facemask when working with the unit in dusty en vironments Dress safely in long pants Do not go barefoot or wear short pants or san dals Do not operate the unit when you are tired ill upset or if you are under the influence of alcohol drugs or medica tion Secure hair so it is above shoulder length Keep loose hair loose cloth ing fingers and all other parts of the body away fromopenings and moving parts Hair je
12. hair and anything that may reduce air flow STANDARDS This product is listed by Underwriters Laboratories Inc in accordance with UL Standard 1017 If situations occur which are not cov ered in this manual use care and good judgment If you need assis tance contact your Sears Service Center or call 1 800 235 5878 Fail ure to follow all Safety Rules and Pre cautions can result in serious injury SAVE THESE INSTRUCTIONS ASSEMBLY CARTON CONTENTS Model 358 799380 Blower Blower Tube Nozzle 2 Vacuum Tubes Collection Bag Examine parts for damage Do not use damaged parts NOTE If you need assistance or find parts missing or damaged call 1 800 285 5878 ASSEMBLY A WARNING If received as sembled repeat all steps to ensure your unit is properly assembled and all fasteners are secure ASSEMBLY INSTRUCTIONS FOR USING YOUR UNIT AS A BLOWER NOTE Assembly instructions for using your unit as a vacuum follow this sec jon ATTACHING THE BLOWER TUBE AND NOZZLE If you have already assembled your unit for use as a vacuum remove the vacuum tubes and the collection bag Insert the blower tube into the blower outlet Twist the blower tube clockwise until it is firmly seated in the blower outlet e Twist the nozzle into the end of the blower tube until it is firmly seated Make sure the nozzle points upward Blower Outlet ASSEMBLY INSTRUCTIONS FOR USING YOUR UNIT AS A VACUUM NOTE
13. ied service personnel Replacement parts for a double insulated appliance must be identical to the parts they replace A double insulated appliance is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol 5 square within a square may also be marked on the appliance Failure to have the unit repaired by Sears ser vice personnel can cause the double insulation construction to become inef fective and result in serious injury UNIT MAINTENANCE SAFETY e Turn off all controls and allow the mo tor to stop before disconnecting the unit from the power source Disconnect the unit from the power source when notin use Do not leave the unit when it is plugged into outlet Do not set the unit on any surface ex cepta clean hard area while the unitis running Debris such as gravel sand dust grass etc could be picked up by the air intake and thrown out through the discharge opening dam aging the unit property or causing se rious injury to bystanders or operator Donotoverreach or use fromunstable surfaces such as ladders trees steep slopes rooftops etc Use extra care when cleaning on stairways Keep firm footing and balance at all times Keep hands out of tubes Inspect the entire unit before each use for worn loose missing or damaged parts Do not use until the unit is in proper working order Disconnect unit from power source before servicing cleaning performing maintenance or storing This un
14. ight Inspect the area before using the unit Remove all debris and hard objects such as rocks glass wire etc that can ricochet be thrown or otherwise Cause injury or damage Avoid accidental starting Be sure the switch is in the OFF position and keep your hand and fingers away from the switch while connecting the unit to the power source or when carrying a unit connected to the power source Never run the unit without the proper equipment attached When used as a blower always install a blower tube Use only recommended attachments Do not use with any opening blocked Keep free of dust lint hair and any thing that may reduce air flow To avoid spreading fire do not use blower near leaf or brush fires fire places barbecue pits ashtrays etc Never place objects inside the blower tubes always direct the blowing de bris away from people animals glass and solid objects such as trees auto mobiles walls etc The force of air can cause rocks dirt or sticks to be thrown or to ricochet which can hurt people or animals break glass or cause other damage Never use for spreading chemicals fertilizers or any other substances which may contain toxic materials VACUUM SAFETY Stop the motor and disconnect the power source before opening the air inlet door or attempting to insert or re move the vacuum tubes The motor must be stopped and the impeller blades no longer turning to avoid seri ous injury fr
15. it is Double Insulated See the DOUBLE INSULATION section Have all internal service performed by quali fied service repair personnel to avoid creating a hazard or voiding your war ranty Have all maintenance other than the recommended procedures described in the Operator s Manual performed by your Sears Service Center Always see your Sears Service Cen ter to replace a damaged impeller Parts that are chipped cracked bro ken or damaged in any other way can fly apart and cause serious injury Re place damaged parts before using the unit Never place any object in the air intake Opening as this could restrict proper air flow and cause damage to the unit Never douse the unit with water or oth er liquids or squirt with a water hose Clean with a damp sponge and mild soap See STORAGE Check air intake openings and tubes frequently always with the unit stopped and power source discon nected Keep vents and tubes free of debris which can accumulate and re strict proper air flow Do not bum incinerate or expose this unit to extreme heat e Store the unit unplugged in a high cool dry indoor area out of the reach of children Use only recommended attachments and replacement parts to avoid creat ing a hazard and or voiding warranty e Maintain the unit according to recom mended procedures Use only for jobs explained in this manual BLOWER SAFETY Use only in daylight or in good artificial l
16. om the rotating blades e Hard objects can be thrown through the collection bag or the housing and become dangerous missiles which can cause serious injury to the opera tor or others When using the vacuum attachment the unit is designed to pick up dry ma terial such as leaves grass small twigs and bits of paper Do not vacu um stones gravel metal broken glass etc to avoid severe damage to the impeller To avoid the possibility of electrical shock do not attempt to vac uum water or other liquids Never run the unit without the proper equipment attached When used asa vacuum always install vacuum tubes and collection bag assembly Make sure the collection bag assembly is completely zipped when unit is run ning to avoid flying debris Use only recommended attachments Avoid situations which could set the collection bag on fire Do not vacuum discarded matches cigars cigarettes or ash from fireplaces barbecue pits brush piles etc To avoid spreading fire do not use blower near leaf or brush fires fireplaces barbecue pits ashtrays etc Always use the collection bag shoul der strap when vacuuming to avoid loss of control e Check air intake openings elbow tube and vacuumtubes frequently al ways with the unit stopped and the power source disconnected Keep vents and tubes free of debris which can accumulate and restrict proper air flow Do not use with any opening blocked Keep free of dust lint
17. ry Store unit well out of the reach of children BLOWER STORAGE Disconnect from the power source Clean the entire unit Open inlet cover and clean any dirt TROUBLESHOOTING CHART Unit fails to operate blown Mechanical failure Unit vibrates abnormally Mechanical failure Impeller will not turn freely Mechanical failure SYMPTOM CAUSE Switch in the OFF position Extension Cord Disconnected Circuit breaker tripped or fuse Debris in air intake area grass or debris that has collected Inspect the blower and all tubes Close and make sure the cover is latched Clean air vents and air inlet of debris Store your unit and extension cord in a well ventilated area and covered if possible to prevent dust and dirt ac cumulation Do not cover with plastic Plastic cannot breathe and may cause condensation and eventual rust or corrosion Check entire unit for loose screws nuts and bolts Replace any dam aged worn or broken parts REMEDY Slide switch to ON position Reconnect extension cord Reset circuit breaker or fuse Contact your Sears Service Center Contact your Sears Service Center Clean unit Remove any debris Contact your Sears Service Center 10
18. welry loose clothing or clothing with loosely hanging straps ties tassels etc can be caught in moving parts ELECTRICAL SAFETY Use only a voltage supply as shown on the name plate of the unit Avoid dangerous situations Do not use in presence of flammable liquids or gases to avoid creating a fire or ex plosion and or causing damage to unit e Avoid dangerous environments Do not use in unventilated areas or where dust or explosive vapors can build up TO REDUCE THE RISK OF ELEC TRICAL SHOCK Do not use in damp or wet locations or around swim ming pools hot tubs etc Do not ex pose to snow rain or water Do not handle extension cord plug or unit with wet hands To reduce the risk of electrical shock use extension cords specifically marked as suitable for outdoor ap pliances having electrical rating not less than the rating of the unit The cord must be marked with the suffix W A in Canada W Use a polar ized cord Make sure your extension cord is in good condition If damaged have the cord replaced An under sized extension cord will cause a drop in line voltage resulting in loss of pow erandoverheating ifin doubt usethe next heavier gauge The smaller the gauge number the heavier the cord NOTE The correct size to be used depending on the cord length is shown in this manual To reduce the risk of electrical shock this equipment has a polarized plug one biade is wider than
Download Pdf Manuals
Related Search