Clearaudio Champion Turntable User Manual
Contents
1. Champion LEVEL 1 Assembly and User Manual Loving music clearaudio electronic GmbH 2006 oe Champion Level 1 USER MANUAL DEAR AUDIO ENTHUSIAST Thank you for your decision to purchase a clearaudio Champion Level 1 turntable This turntable is manufactured to the highest degree of tolerance and quality Please take a moment to read this owner s manual to ensure correct set up to avoid any possible damage and to learn how proper care of your clearaudio Champion Level 1 turntable which will give you many years of musical enjoyment and pleasure clearaudio electronic GmbH Contents 1 Front view 3 2 Package contents 4 3 Assembly and Operation 6 4 Speed calibration 9 5 Special instructions 9 6 Service 9 7 Technical data 11 Page 2 clearaudio electronic GmbH 2006 ae P a Loving music Champion Level 1 USER MANUAL 1 Front view The photo below shows the clearaudio Champion Level 1 turntable assembled and set up with the Unify tonearm You can see the use of carefully selected materials and the resonance avoiding construction Further the stand alone Motor reduces any induced vibrations and resonances to the turntable chassis qi F ii i x Ha ij chen id Pe e S M i 5 nie al Champion Level 1 assembled and set up 2 Package contents The clearaudio Champion Level 1 turntable is delivered in a special packaging to ensure its safe transport Please2. the screw of the bearing and to the earth connector of your amplifier The clearaudio Champion Level 1 turntable is now completely assembled and you can now enjoy listening to music 4 Speed calibration Install the drive belt first around the platter then around the motor pulley There are two diameters on the motor pulley e smaller for 33 1 3 rpm e larger for 45 rom To correctly adjust the belt tension turn the motor around its axis Proper tension will be achieved through eccentric placement of the motor pulley or if you have enough space on your platform just change the distance between the motor and the turntable chassis The belt tension is correct if the belt can be deflected by approximately 3 4inch by a finger 5 SPECIAL INSTRUCTIONS Please take the time to fill out the enclosed warranty card and return it to Clearaudio or your local distributor dealer If you do not return this card within 14 days of purchase the guarantee will only be for a period of two years from the date of purchase During any transportation of the turntable always remove the platter and inverted bearing If this is not done DAMAGE COULD OCCUR Please regularly check the mains leads of your motor assembly If there is any damage to any wires or the mains plug have them replaced immediately by a qualified person your dealer or distributor To clean the turntable use only special acrylic cleaner which is not alcohol based Otherwise y
3. check the contents as shown in the picture below and in the list on the next page Page 3 clearaudio electronic GmbH 2006 _ Champion Level 1 USER MANUAL Overview of package contents Not shown a pair of white gloves s_ Sfanpen aie cassis win row eaira 10 Chapin seve cas T Compe resembled Sarcane a REGRomwioweah z poeno reren fe ee en Grounding cable to ground the bearing screw 15 High precision turntable platter made out of solid n dl Sacetaiaial clearaudio Clever Clamp 16 Hex key wrenches one to adjust the tonearm n fattest reson nt ane eine Page 4 clearaudio electronic GmbH 2006 evn A Champi O Level1 USER MANUAL 3 Assembly and Operation First please put on the white gloves to avoid finger prints on the surface of the acrylic chassis during installation 1 Place first the lower part chassis on a clean and soft surface Please pay attention that the surface of your HiFi rack is horizontal and vertical correctly adjusted by using the delivered level gauge Important Never turn the Spikes of the turntable chassis they had been adjusted in the factory Use the delivered Flad Pads to avoid scratches on the surface of your HiFi rack After that place the chassis with the mounted bearing onto the first one 2 Now unpack your turntable platter and place the platter carefully on the upper part of the bearing whi
4. ampi O Level1 USER MANUAL 7 Turn the tonearm into the final position where the tonearm is almost parallel to the right hand edge of the chassis After that you can fix the tonearm in this position by holding the tonearm nut with one hand and turning the tonearm against while using the other hand or tight the large nut with a wrench Mount the tonearm counterweight 8 To change the height of the tonearm lift turn it up to the high position and loosen the little screw at the front Now you can move the plate of the lift The distance between record and cartridge diamond when it is lifted up should be about 5mm Tighten the screw again 9 Place the belt first round the platter then round the smaller diameter of the pulley 33 1 3 rpm 10 The tension of the belt can be changed by turning the motor about its axis The tension is correct if the correct turntable speed is achieved within 10 seconds If the tension is too high the motor could start to vibrate a little bit If the tension is too loose the turntable will not achieve a constant and correct speed O 11 Assemble the cartridge according to the Plattenteller manufacturer s instructions Motor Riemen Page 7 clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 12 If you should have problems with hum the turntable may need to be grounded In this case connect the grounding wire supplied to
5. ch is mounted in the turntable chassis Important take care not to cause to much pressure 3 Place the pulley on the motor spindle The distance between the pulley and the motor housing should be approx 1 2mm Tighten the little screws inside the pulley with the aluminium screwdriver provided Page 5 clearaudio electronic GmbH 2006 sane lt A f Champi O Level1 USER MANUAL 4 Place the decuppeling base for the motor in the indent of the chassis and place the motor on it The switch of the motor should be on the outside of the turntable and the space between motor and chassis approx 1cm for an exact adjustment see chapter 4 5 Please screw the tonearm carefully into the upper part of the tonearm base Then slide the tonearm nut over the tonearmcable and tighten it but not too much because the tonearm should be still able to turn 6 Now you can While holding the unit you can adjust the tonearm height VTA vertikal tracking angle when you have a cartridge mounted The VTA is adjusted correctly if the tonearm sits parallel to the turntable platter surface after lifting it down Now loosen the six screws with the provided hex key wrench to be able to set the distance between the spindle and the tonarm bearing crosspoint to 222mm by turning the tonearm base After that you can fix the six srews again Page 6 clearaudio electronic GmbH 2006 sent A Ch
6. ou could could damage the material haircracks and spots on the acrylic surface Page 8 clearaudio electronic GmbH 2006 Champion Level 1 USER MANUAL 6 Service If the platter without drive belt does not turn as easy as usual you should squeeze a 5mm long line of the bearing grease into the upper part of the platter bearing If any service or repair on all clearaudio products is necessary please contact your dealer distributor or contact clearaudio directly We will inform you about your nearest service location PLEASE RETAIN ALL ORIGINAL PACKAGING You will need it if this unit has to be transported and or shipped Clearaudio electronic GmbH Spardorfer Str 150 91054 Erlangen Germany Tel Phon 49 0 1805 059595 www clearaudio de info clearaudio de Page 9 clearaudio electronic GmbH 2006 oe Champion Level 1 USER MANUAL 7 Technical Data Construction Geometrically resonance optimized chassis beltdrive Speeds 33 1 3 rpm 45 rpm Drive unit Stand alone synchronous motor Platter bearing Patented inverted bearing with polished ball inside Platter Silicon acrylic surface absolutely plain Speed variation 0 1 Weight Approx 14 Kg with motor Dimensions Approx 470 mm x 390 mm x 180 mm Warranty 5 Years see chapter 5 Page 10 clearaudio electronic GmbH 2006
Download Pdf Manuals
Related Search