Home

Cisco Systems 3200 Network Router User Manual

1. a Cisco 3270 Router 1 0 End Cap Figure 1 7 shows the Cisco 3270 Router I O end cap Figure 1 7 Cisco 3270 Router End Cap 1 Router console port 2 FE0 port 3 FEI port 4 FEOX port 5 GEO Gigabit Ethernet port 6 Fiber Optic port shown or Copper Gigabit Ethernet GE1 port 7 USBO bottom and USBI top ports 8 Ser2 Smart Serial port 9 Power input 10 Serl EIA TIA 232 DCE port 11 AUX port 12 Ser0 EIA TIA 232 DCE port 13 IFEIX port or WMIC 3 console port 14 FE2X port or WMIC 2 console port 15 FE3X port or WMIC 1 console port 1 The configuration of the port is set at the factory and labeled accordingly The RJ 45 connectors identified as 8 9 and 10 are Fast Ethernet ports or WMIC console ports depending on the configuration of the system For example if two WMICs have been added to the router RJ 45 ports 8 and 9 are labeled WMIC 1 and WMIC 2 Port 10 is labeled FEIX Cisco 3200 Series Router Hardware Reference OL 5816 10 EN Chapter1 Cisco 3200 Rugged Enclosures amp Note The connectors are sealed at the factory with captive dust covers not shown that seal the ports and protect the pins The dust covers should be used to seal the ports when the ports are not covered by cable connectors Fiber Optic Connector IP 67 Integrity When the fiber optic port is not connected or otherwise in use the protective cover should be used to seal the port To s
2. 135533 amp Note By default the Cisco 3205 WMIC uses the right antenna to receive and transmit data Cisco 3200 Series Router Hardware Reference OL 5816 10 EN Chapter1 Cisco 3200 Rugged Enclosures amp Note For additional information on antennas and antenna cables see the Antenna Basics technical note at http www cisco com en US products hw wireless ps458 products_installation_guide_chapter09186a0 08007f74a html and the Antenna Cabling technical note at http www cisco com en US tech tk722 tk809 technologies_tech_note09186a00801c12c2 shtml 1 0 End Caps for the Cisco 3200 Rugged Enclosures The I O end cap has multiple connectors for connecting power and data cables The end cap configurations shown in this section are fully populated however the number of ports and their functions may differ depending upon the number of WMICs in the system End Cap Fast Ethernet and WMIC Console Ports Internally five Fast Ethernet ports are available one routed Fast Ethernet port on the router card and four switched Fast Ethernet ports on the Fast Ethernet Switch Mobile Interface Card FESMIC When a WMIC is installed in addition to the router the WMIC Fast Ethernet port is connected internally to the routed Fast Ethernet port on the router card or is connected to one of the switched Fast Ethernet ports on the FESMIC to provide a communications link with the router In contrast th
3. mode Command Purpose Step1 Router config interface vlan vlan id Selects the interface to be configured slot port Step2 Router config if ip pim dense mode Enables IP PIM on a Layer 3 interface sparse mode sparse dense mode This example shows how to enable PIM on an interface using the default mode sparse dense mode Router config if ip pim Router config if This example shows how to enable PIM sparse mode on an interface Router config if ip pim sparse mode Router config if Cisco 3200 Series Router Hardware Reference cio i OL 5816 10 Appendix C Switch Port Functionality IP Multicast Layer 3 Switching W Verifying IP Multicast Layer 3 Hardware Switching Summary D The show ip pim interface count command verifies the IP multicast Layer 3 switching enable state on IP PIM interfaces and the number of packets received and sent on the interface Note Step 1 Step 2 The show interface statistics command does not verify hardware switched packets only packets switched by software Use the following show commands to verify IP multicast Layer 3 switching information for an IP PIM Layer 3 interface as illustrated below Enter the show ip pim interface count command Router show ip pim interface count State Fast Switched D Distributed Fast Switched H Hardware Switching Enabled Address Interface FS Mpackets In Out 10 15 1 20 GigabitEthernet4 8 H 952 423
4. 7 AUX port 8 Router console port 9 Ser0 RS 232 DCE port 10 Serl RS 232 DCE port 11 Power input amp Note The connectors are sealed at the factory with captive dust covers not shown that seal the ports and protect the pins The dust covers should be used to seal the ports when the ports are not otherwise covered by cable connectors E Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures Protective End Cap Cover A protective end cap cover Figure 1 9 provides weatherproof protection for the ports on the end caps of the Cisco 3200 Rugged Enclosure when the enclosure is installed outdoors The protective end cap cover also provides added protection for in vehicle use inhibiting corrosion on the ports and potential damage from objects that are stored near the enclosure inside a vehicle The protective end cap cover has a ruggedized design for high reliability and NEMA4 compliance Figure 1 9 Cisco 3200 Rugged Enclosure Protective End Cap Cover 1 Hinge point 2 NEC cable pass through 3 Holes for 8 32 protective end cap cover 4 Hinge mounting bracket screws 5 Mounting bolt Cisco 3200 Series Router Hardware Reference OL 5816 10 EEN Chapter1 Cisco 3200 Rugged Enclosures Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 To attach the protective end cap cover to the enclosure follow these steps
5. 30 mW 15 dBm 20 mW 13 dBm 5 mW 7 dBm 1 mW 0 dBm Maximum power settings vary to comply with the regulatory domain OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 6 Wireless Mobile Interface Cards Table 6 5 Key 2 4 GHz 802 11b g WMIC Features Feature Description Range typical at 100 mW transmit power setting with 6 dBi diversity dipole antenna Outdoor 0 5 mile 804 m at 45 Mbps 1 mile 1609 m at 11 Mbps 3 miles 4 827 m at 1 Mbps Compliance 2 4 GHz 802 1 1b g operates license free under FCC Part 15 and qualifies as a Class B device complies with DOC regulations complies with ETS 300 328 FTZ 2100 and MPT 1349 standards rugged version complies with UL 2043 Quadrature PSK maaa e ID A Binarv Phase shift keving PSK Complementarv Code Keving Quadrature Amplitude Modulation Table 6 6 shows the channel identifiers channel center frequencies and regulatorv domains of each IEEE 802 11b g 22 MHz wide channel Table 6 6 Channels for IEEE 802 11b g Center Channel Frequency Identifier MHz Regulatory Domains Americas A EMEA E Japan J CCK OFDM CCK OFDM CCK OFDM 1 2412 2417 2422 2427 2432 2437 2442 2447 iO CO NAN DW Nm BB WwW b 2452 2457 j 2462 P PS PS K PS PS OS P PS PS PST PS OS OS OS OK OX
6. Etype Tag Len Etype Data FCS Frame VLAN ID and Etype VLAN ID TR encapsulation are Lt tt tt ft 802 1Q not 802 IP Token Ring Encapsulation Flag Inter VLAN Routing 82634 In a VLAN network traffic and stations for multiple network layer subnets VLANs can coexist on a single physical LAN segment In practice a single VLAN corresponds to a network subnet and a VLAN trunking capable router is required to forward traffic from a first VLAN to a second VLAN for a Layer 2 switch The FESMIC enables the Cisco 3200 Series router to become one of first IOS Ethernet switching routers to deliver intelligent Layer 2 switching capability and Layer 3 inter VLAN routing in a single box solution as shown in Figure C 4 Figure C 4 Traditional Switch and Router Topology VLAN1 VLAN2 VLAN3 Switching Router Network Topology Switching Router Topology VLAN1 VLAN2 Switching Router VLAN3 Floor 3 i li ti Floor 3 Switching mj il aj T Router Floor2 jf i i HA aa idi EE Floor Router a ii i Ss Switching I l i Router Floori fay Floor1 L2 Switch i ii Cisco 3200 Series Router Hardware Reference mem OL 5816 10 Appendix C Switch Port Functionality Inter VLAN Routing W In a typical IOS managed Layer 2 switch there would be one Layer 3 Switch Virtual Interface SVI that
7. Router 82632 Port Based VLAN By default the 10 100 Fast Ethernet interfaces on the FESMIC are defaulted to Layer 2 switch ports and all four interfaces belong to VLAN 1 You can partition the switch ports to belong to different VLAN groups by using the switchport vlan access lt vlan id gt command The following is a brief function description of a FESMIC port based VLAN e Each VLAN has its own MAC address table e Packets received are forwarded only to ports that are members of the same VLAN as the receiving port VLAN partitions provide hard firewalls for all traffic in different VLANs e A VLAN comes into existence when a user adds a VLAN to the local VLAN database A maximum of 32 VLANs are supported VLAN IDs can range from 1 to 1005 e By default a spanning tree instance is created for each VLAN Cisco 3200 Series Router Hardware Reference mm OL 5816 10 Appendix C Switch Port Functionality 802 10 Trunking W 802 10 Trunking A trunk is a point to point link between one or more Ethernet switch ports and another networking device such as a router or a switch Trunks carry the traffic of multiple VLANs over a single link and they allow you to extend VLANs across an entire network as shown in Figure C 2 The IEEE 802 1q protocol is an industry standard trunking encapsulation Figure C 2 802 10 Trunk Port Application Ci ml VLAN2 VLAN2 WT VLAN1 2 3 A VLANS jmmmi mv g fey T VLAN1
8. Switch Port Functionality IP Multicast Layer 3 Switching ICMP unreachables are never sent ICMP mask replies are never sent fast switching is enabled U U U Flow switching is disabled CEF switching is enabled Fast switching turbo vector Normal CEF switching turbo vector multicast fast switching is enabled U U U U U route cache flags are Fast CEF outer Discoverv is disabled P output packet accounting is disabled P access violation accounting is disabled TCP IP header compression is disabled RTP IP header compression is disabled Probe proxv name replies are disabled Policv routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled IP multicast multilayer switching is enabled IP mls switching is enabled Router HH DHHHHHHHHH U Verifving the IP Multicast Routing Table Use the show ip mroute command to verifv the IP multicast routing table Step1 Enter the show ip mroute command Router show ip mroute 230 13 13 1 IP Multicast Routing Table Flags D Dense S Sparse s SSM Group C Connected L Local P T SPT bit set J Join SPT M MSDP created entry X Proxy Join Timer Running A Pruned R RP bit set F Register flag fast switching on the same interface is disabled multicast distributed fast switching is disabled Advertised via MSDP U U
9. jamii N 2467 w 2472 P P PM PK PK PS OX P P PK PK PK PS OP P S PS OS PK OST PK PST PS PS OPK OPS B 2484 P P P PK PK OPK PS P OX E Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter6 Wireless Mobile Interface Cards Universal Workgroup Bridge Limitations The following limitations and restrictions apply to universal workgroup bridges A universal workgroup bridge cannot associate with the Cisco WLAN AP when the bridge is configured with CKIP or CMIC encryption If the universal workgroup bridge is associated with a Cisco AP or third party AP and if the user issues the show dot11 association all command the IP address and name information is not available Users should configure the static IP address on the Bridge Group Virtual Interface BVI when it is in the universal workgroup bridge mode so that the WMIC is manageable from the MAR through the Mobile IP tunnel from the infrastructure side If the dynamic Collocated Care of Address CCoA is used on the Cisco 3200 Series Wireless and Mobile Router you should configure the static IP address using the ip secondary address command The universal workgroup bridge is not compatible with the Tropos version 3 1 1 2 AP A universal workgroup bridge cannot associate with the Cisco 1500 router when it is configured with the Allow WPA2 TKIP Cli
10. 5 1 6 2 c card stack Cisco 3230 1 6 Cisco 3270 1 4 CCITT V 35 5 1 CCXv4 6 10 channel 2 4 GHz center frequencies 6 11 4 9 GHz center frequencies 6 13 Cisco IOS image release 6 7 Cisco WMIC 2 4 GHz 6 10 4 9 GHz 6 13 class of service CoS 4 1 commands duplex 2 6 errdisable recovery B 4 line con 2 4 3 1 AUX port power local 6 7 enclosure 1 17 show controller 1 15 MARC 3 4 show interface 6 16 speed 2 4 speed 4 2 Cisco 3200 Series Router Hardware Reference OL 5816 10 om IN index speed auto 2 6 station role 1 19 connectivity problems solving B 3 console port Cisco 3270 Rugged Router card 2 1 MARC 3 4 WMIC 1 17 WMIC console LEDs 1 19 cooling 1 20 cover end cap 1 13 crossover cable 4 2 crypto channels 2 4 D Data Encryption Standard DES 2 5 Data Encryption Standard Execution Unit DEU 2 7 data rates 6 10 DCE 1 17 3 4 5 1 declassification 2 5 DFS 6 16 double data rate DDR 2 1 DRAM 3 1 DTE 1 17 3 4 5 1 duplex command 2 6 EAP FAST 6 9 EIA TIA 232 5 1 EIA TIA 449 5 1 EIA TIA 530 5 1 EIA TIA 530A 5 1 EIA TIA X 21 5 1 enclosure interface cards 1 1 mounting 1 1 encryption 6 5 end cap antenna 1 7 Cisco 3230 router I O 1 12 Cisco 3270 router I O 1 9 protective cover 1 13 errdisable recovery command B 4 error SFP module B 4 USB Flash storage device 1 11 Execution Units EUs 2 4 F Fast Ethernet auto negotiation 4 2 Cisco 3270 R
11. 802 11b g command line interface CLI Concatenation Supported Not supported Not supported Autonomous Modes Work Group Bridge Work Group Bridge Work Group Bridge Supported WGB Universal WGB WGB Non Root Bridge WGB Non Root Bridge Non Root Bridge NRB NRB Root Bridge NRB Root Bridge Root Bridge RB RB and Access Point RB and Access Point Repeater and Access AP AP Point AP World Mode Supported Not supported Not supported World mode on the client side updates a client with the channels of the specified domain The Cisco 3200 Series router is limited to fixed channels so world mode is not available on the client side Universal Supported Not supported Not supported Enables operation Workgroup Bridge with non Cisco Mode access points Multiple Client Supported Supported Supported Profiles Multiple Basic Supported Supported Supported This mode is for root SSIDs access point only Wireless WEP 40 WEP 128 WEP 40 WEP 128 WEP 40 WEP 128 encryption cipher TKIP CKIP CMIC and TKIP and AES CCM TKIP and AES CCM suites CKIP CMIC Max Number of 255 116 116 Stations with WEP Max Number of 256 26 26 Stations with TKIP Max Number of 256 116 116 Stations with AES CCM E Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter6 Wireless Mobile Interface Cards
12. bridge archive tar table flash c1200 k9w7 mx 122 8 JA html1 c1400 k9w7 mx 122 11 JA html directory c1400 k9w7 mx 122 11 JA html foo html 0 bytes Extracting a tar File To extract a tar file into a directory on the flash file system use this privileged EXEC command archive tar xtract source url flash file url For source url specify the source URL alias for the local or network file system These options are supported Cisco 3200 Series Router Hardware Reference OL 5816 10 L Chapter 7 Managing Firmware and Configurations Working with Configuration Files W e For the local flash file system the syntax is flash e For the File Transfer Protocol FTP the syntax is ftp username password location directory tar filename tar e For the Remote Copy Protocol RCP the syntax is rep username location directory tar filename tar e For the Trivial File Transfer Protocol TFTP the syntax is tftp location directory tar filename tar The tar filename tar is the tar file from which to extract files For flash file url specify the location on the local flash file system into which the tar file is extracted You can also specify an optional list of files or directories within the tar file for extraction If none are specified all files and directories are extracted This example shows how to extract the contents of a tar file located on the TFTP server at 172 20 10 30 This command extracts
13. see Figure 1 10 Figure 1 10 Protective End Cap Cover Installation i 1 Hinge bracket 2 Hinge point 3 Cable service loop cavity 4 NEC pass through 5 Gasket 6 Cap mounting Loosen the end cap mounting hardware four 1 4 20 bolts but do not remove the bolts Slide the hinge brackets onto the right side and the left side of the end cap cover The mounting tabs should slide under the loosened bolts Re torque the two loosened bolts on the right side of the end cap cover to between 58 and 68 in Ib Ensure that the gasket is fully seated in the protective end cap cover Close the cover on the protective end cap cover and ensure that it is fully seated Re torque the end cap cover bolts on left side of the end cap cover to between 58 and 68 in Ib Tighten the 8 32 protective cover screws 18 in Ib until they are seated For sealing we recommend Liquid Tight Connector which is described at the following URL http www newark com Newark WebCommerce newark en_US mfr brands jsp mfg HUBB Cisco 3200 Series Router Hardware Reference iia OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures 1 0 End Cap Port Signals This section describes the ports and port signals on the Cisco 3200 Rugged Enclosure I O end caps Gigabit Ethernet Signal Limitations Due to CPU and memory bus limitations a Gigabit Ethernet port transmits and receives packets below the line rate The line rate is
14. 136 5700 MHz 140 e For C3205 ETSI the following channels are supported e 5500 MHz channel 100 e 5520 MHz channel 104 e 5540 MHz channel 108 e 5560 MHz channel 112 e 5580 MHz channel 116 e 5600 MHz channel 120 e 5620 MHz channel 124 e 5640 MHz channel 128 e 5660 MHz channel 132 e 5680 MHz channel 136 Cisco 3200 Series Router Hardware Reference oie I OL 5816 10 Chapter6 Wireless Mobile Interface Cards e 5700 MHz channel 140 Related Documentation These documents provide detailed information regarding the configuration of the wireless card e Cisco IOS Switching Services Configuration Guide Click this link to browse to this document http www cisco com univercd cc td doc product software ios 122 122cgcr fswtch_c index htm e Cisco Internetwork Design Guide Click this link to browse to this document http www cisco com univercd cc td doc cisintwk idg4 index htm e Cisco Internetworking Technology Handbook Click this link to browse to this document http www cisco com univercd cc td doc cisintwk ito_doc index htm e Cisco Internetworking Troubleshooting Guide Click this link to browse to this document http www cisco com univercd cc td doc cisintwk itg_v1 index htm Cisco 3200 Series Router Hardware Reference OL 5816 10 M 647 Chapter6 Wireless Mobile Interface Cards Cisco 3200 Series Router Hardware Reference OL 5816 10 CHAPTER Managing Firmware
15. 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Class 1 laser product Statement 1008 To insert an SFP module into the SFP module slot follow these steps Attach an ESD preventive wrist strap to your wrist and to a bare metal surface on the chassis Remove the antenna end cap by using a 3 8 in wrench to loosen the bolts Disconnect the LC from the SFP module p Tip For reattachment note which cable connector plug is send TX and which is receive RX Insert a dust plug into the optical ports of the SFP module to keep the optical interfaces clean A Caution Do not touch the optical surfaces Unlock and remove the SFP module Figure B 2 Disconnecting SFP Latch Mechanisms 117722 Pull the bale clasp latch out and down to eject the module If the bale clasp latch is obstructed and you cannot use your index finger to open it use a small flat blade screwdriver or other long narrow instrument to open the bale clasp latch Grasp the SFP module between your thumb and index finger and carefully remove it from the module slot Place the removed SFP module in an antistatic bag or other protective environment A Caution Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber optic cable until you are ready to connect the cable The plugs and caps protect the SFP module ports and cables from contamination and ambient light Cisco 3200 Serie
16. 30 dBm EIRP Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter6 Wireless Mobile Interface Cards Modulation Table 6 11 lists the supported 5 0 GHz 802 11h modulations and data rates Table 6 11 5 0 GHz 802 11h Modulations and Data Rates Modulation 20 Mbps BPSK 6 Mbps and 9 Mbps OPSK 12 Mbps and 18 Mbps 16 OAM 24 Mbps and 27 Mbps 64 OAM 48 Mbps and 54 Mbps Receive Sensitivity Table 6 12 shows the receive sensitivity for 5 0 GHz 802 11h radios Table 6 12 Receive Sensitivity for 5 0 GHz 802 11h Radios Data Rates 5 25 GHz to 5 35 GHz 5 47 GHz to 5 725 GHz 5 725 GHz to 5 825 GHz 6 Mbps 85 dBm 85 dBm 85 dBm 9 Mbps 85 dBm 85 dBm 85 dBm 12 Mbps 85 dBm 85 dBm 85 dBm 18 Mbps 82 dBm 82 dBm 82 dBm 24 Mbps 79 dBm 79 dBm 79 dBm 36 Mbps 76 dBm 76 dBm 76 dBm 48 Mbps 71 dBm 71 dBm 71 dBm 54 Mbps 69 dBm 69 dBm 69 dBm 1 The 5 725 GHz to 5 825 GHz range is not supported on European models Transmit Sensitivity Table 6 13 shows the transmit sensitivity for 5 0 GHz 802 1 1h radios Table 6 13 Transmit Sensitivity for the C3205 WMIC Data Rates 5 25 GHz to 5 35 GHz 5 47 GHz to 5 725 GHz 5 725 GHz to 5 825 GHz 6 Mbps 16 dBm 16 dBm 16 dBm 9 Mbps 16 dBm 16 dBm 16 dBm 12 Mbps 16 dBm 16 dBm 16 dBm 18 Mbps 16 dBm 16 dBm 16 dBm 24 Mbps 16 dBm 16 dBm 16 dBm 36 Mbps 16 dBm 16 dBm 16 dBm 48 Mbps 14 dBm 14 dB
17. 3200 Series Router Hardware Reference E Appendix C Switch Port Functionality E IGMP Snooping To verify IGMP snooping use the show mac address table multicast igmp snooping command Router show mac address table multicast igmp snooping To verify the multicast routing table use the show ip mroute command Router sh ip mroute CCDE CCENT Cisco Eos Cisco Lumin Cisco Nexus Cisco StadiumVision the Cisco logo DCE and Welcome to the Human Network are trademarks Changing the Way We Work Live Play and Learn is a service mark and Access Registrar Aironet AsyncOS Bringing the Meeting To You Catalyst CCDA CCDP CCIE CCIP CCNA CCNP CCSP CCVP Cisco the Cisco Certified Internetwork Expert logo Cisco IOS Cisco Press Cisco Systems Cisco Systems Capital the Cisco Systems logo Cisco Unity Collaboration Without Limitation EtherFast EtherSwitch Event Center Fast Step Follow Me Browsing FormShare GigaDrive HomeLink Internet Quotient IOS iPhone iQ Expertise the iQ logo iQ Net Readiness Scorecard iQuick Study IronPort the IronPort logo LightStream Linksys MediaTone MeetingPlace MGX Networkers Networking Academy Network Registrar PCNow PIX PowerPanels ProConnect ScriptShare SenderBase SMARTnet Spectrum Expert StackWise The Fastest Way to Increase Your Internet Quotient TransPath WebEx and the WebEx logo are registered trademarks of Cisco Systems Inc and or its affiliates in the United States
18. 4 Key Features 6 5 2 4 2 8 Cisco 3200 Series Router Hardware Reference OL 5816 10 MAC Address Allocation 6 7 WMIC Power Requirement 6 7 Mean Time Between Failure 6 7 Differences Between WMICs 6 7 2 4 GHz 802 11b g WMIC Features 6 10 Universal Workgroup Bridge Limitations Contents ll 6 12 4 9 GHz Public Safety WMIC Features 6 13 4 9 GHz Channels 6 13 Throughput 6 14 Modulation 6 14 Receive Sensitivity 6 15 5 0 GHz 802 11h Radio Features 6 15 5 0 GHz 802 11h Channels 6 15 Throughput 6 16 Modulation 6 16 Receive Sensitivity 6 16 Transmit Sensitivity 6 17 Related Documentation 6 17 Replacing SFP Modules into SFP Module Slots Diagnosing SFP Problems B 3 Error Messages B 4 B 2 OL 5816 10 Cisco 3200 Series Router Hardware Reference mi E Contents Cisco 3200 Series Router Hardware Reference o E OL 5816 10 Introduction to the Cisco 3200 Series Routers The Cisco 3200 Series routers provides industry standard network software features that run on ruggedized hardware suitable for harsh environments A router includes a combination of mobile interface cards and a Cisco 3200 Rugged Enclosure The following major components are available from Cisco e Cisco 3200 Rugged Enclosures e Cisco 3270 Rugged Router card e Mobile Access Router Card MARC e Fast Ethernet Switch Mobile Interface Cards FESMICs e Serial Mobile Interface Cards SMICs e Wireless Mobile Interface Ca
19. 5 1 processor 2 1 3 1 protective end cap cover 1 13 Public Key Execution Unit PKEU 2 5 2 7 Q QoS 6 5 6 10 Hl Cisco 3200 Series Router Hardware Reference OL 5816 10 radio indicator 6 4 range 6 11 Random Number Generator RNG 2 7 receive drop counter 1 15 receive sensitivity 6 16 roaming 6 10 rotary switch 5 3 Cisco FESMIC 4 5 Cisco SMIC 5 3 5 4 RP TNC 1 7 6 2 rugged enclosure 1 1 rugged enclosure Cisco 3230 1 6 features 1 1 T O end cap 1 12 rugged enclosure Cisco 3270 card stack 1 4 features 1 1 S seal method 1 2 seal the smart serial ports A 1 security engine 2 4 2 7 serial asynchronous port 1 17 3 4 signals 3 1 serial interface Cisco MARC 3 1 Cisco SMIC 5 3 5 4 SFP module bale clasp latch B 2 qualified parts B 1 replacement B 2 to B 3 replacement instructions B 1 show controller command 1 15 show interface dO dfs command 6 16 signals Cisco FESMIC 4 4 Cisco MARC 3 3 Cisco SMIC 5 3 Fast Ethernet 3 3 4 1 6 2 ISA bus 2 2 3 2 4 3 6 1 PCI bus 2 2 3 1 4 3 6 1 serial 3 3 5 3 signal strength installation mode 1 19 sleep mode 6 3 smart serial port seal A 1 system integrity 1 10 SNMP 6 5 6 10 Spanning Tree Protocol STP 4 2 speed auto command 2 6 speed command 4 2 SRTP 2 7 SSL TLS 2 7 station role command 1 19 status indicators 6 4 Switch Virtual Interface SVI 2 8 system integrator vii Index W T temperature sensor Cisco 3270 2 8 thermal plat
20. Cisco 3270 Router Card Stack with Three Optional WMICs 270441 1 WMIC 1 2 MRPC 3 MARC 4 SMIC 5 FESMIC 6 WMIC 2 7 WMIC 3 8 Small form factor pluggable SFP module 9 Second PCI bus E Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures Cisco 3230 Rugged Enclosure The Cisco 3230 Rugged Enclosure is designed to accommodate the Mobile Access Router Card MARC This enclosure operates in a temperature range from 40 to 165 F 40 to 74 C and is certified to meet NEMA4 requirements Figure 1 4 shows an example of a Cisco 3230 Rugged Enclosure Figure 1 4 Cisco 3230 Rugged Enclosure 1 Front of the enclosure I O end cap 2 Back of the enclosure antenna end cap 1 This end cap shows four serial ports but the typical configuration has two serial ports Cisco 3200 Series Router Hardware Reference OL 5816 10 MS Chapter1 Cisco 3200 Rugged Enclosures Cisco 3230 Router Card Stack The Cisco 3230 Rugged Enclosure can accommodate up to seven cards including e One MARC e Up to three WMICs e One SMIC or no SMIC e One FESMIC e One MRPC A basic configuration includes one of each of the following MARC SMIC FESMIC WMIC and MRPC In the Cisco 3230 Rugged Enclosure the cards should be stacked in the order shown in Figure 1 5 The two optional WMICs are on the top of the stack Figure 1 5 Cisco 3230 Rout
21. Directory and image names are case sensitive amp Note amp To avoid an unsuccessful download use the archive download sw safe command which downloads the image first and does not delete the current running version until the download succeeds The download algorithm verifies that the image is appropriate for the WMIC model and that enough DRAM is present or it aborts the process and reports an error If you specify the overwrite option the download algorithm removes the existing image on the flash device whether or not it is the same as the new one downloads the new image and then reloads the software Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version you must specify the overwrite option If you specify the leave old sw the existing files are not removed If there is not enough room to install the new image an keep the running image the download process stops and an error message is displayed The algorithm installs the downloaded image onto the system board flash device flash The image is placed into a new directory named with the software version string and the BOOT environment variable is updated to point to the newly installed image If you kept the old software during the download process you specified the leave old sw keyword you can remove it by entering the delete force recursive filesystem file ur
22. Enclosure I O End Cap LED Indications 1 19 WMIC Console LEDs 1 19 Thermal Plates 1 20 Mounting Brackets 1 21 CHAPTER 2 Cisco 3270 Rugged Router Card 2 1 Cisco 3270 Rugged Router Card Component Systems 2 2 CONTENTS 1 16 Cisco 3200 Series Router Hardware Reference OL 5816 10 IE E Contents Cisco 3270 Rugged Router Card Power Requirements Power Connections AUX 2 4 Hardware Encryption Processor 2 4 Ethernet Port Speed and Duplex Mode 2 6 Cisco 3270 Rugged Router Card Encryption Module 2 7 Security Engine Features 2 7 Temperature Sensor 2 8 Cisco 3270 Rugged Router Card MAC Address Allocation CHAPTER 3 Mobile Access Router Card 3 1 MARC Component Systems 3 2 MARC Power Requirements 3 3 MARC Router Signals 3 3 Fast Ethernet Signals on the MARC 3 3 Console and Auxiliary Signals 3 4 CHAPTER 4 Fast Ethernet Switch Mobile Interface Card 4 1 Autonegotiation and Auto MDI MDIX 4 2 MAC Address Allocation 4 2 FESMIC Component Systems 4 3 Signals for the FESMIC 4 4 FESMIC Rotary Switch Positions 4 5 CHAPTER 5 Serial Mobile Interface Card 5 1 SMIC Component Systems 5 2 Signals for the SMIC 5 3 4 Port SMIC Rotary Switch Positions 5 3 2 port SMIC Rotary Switch Positions 5 4 SMIC LED Signals 5 4 SMIC Power Consumption 5 5 CHAPTER 6 Wireless Mobile Interface Cards 6 1 WMIC Component Svstems 6 1 Antenna Connector 6 2 WMIC Console and Fast Ethernet Ports 6 2 Fast Ethernet Signals on the WMIC 6 3 LED Behavior 6
23. Fa ES l l l T 1 l l l l l number of ll l l l ji l l 1 l l l l l l l l l l broadcast i packets or bytes LI LI LI l LI 46651 When storm control is enabled the switch monitors the packets that are passing from an interface to the switching bus and determines whether the packet is unicast multicast or broadcast The switch monitors the number of broadcast multicast or unicast packets received within the l second time interval and Cisco 3200 Series Router Hardware Reference OL 5816 10 a cis Appendix C Switch Port Functionality HI StormControl when a threshold for one type of traffic is reached that type of traffic is dropped This threshold is specified as a percentage of the total available bandwidth that can be used by broadcast multicast or unicast traffic The combination of broadcast suppression threshold numbers and the l second time interval control the way the suppression algorithm works A higher threshold allows more packets to pass through A threshold value of 100 percent means that no limit is placed on the traffic Note Because packets do not arrive at uniform intervals the l second time interval during which traffic activity is measured can affect the behavior of storm control The switch continues to monitor traffic on the port When the utilization level falls back below the threshold level the type of traffic that was dropped
24. Files by Using FTP You can copy configuration files to or from an FTP server The FTP protocol requires a client to send a remote username and password on each FTP request to a server When you copy a configuration file from the WMIC to a server by using FTP the Cisco IOS software sends the first valid username in this list e The username specified in the copy command if a username is specified e The username set by the ip ftp username username global configuration command if the command is configured e Anonymous The WMIC sends the first valid password in this list e The password specified in the copy command if a password is specified e The password set by the ip ftp password password global configuration command if the command is configured e The WMIC forms a password named username apname domain The variable username is the username associated with the current session apname is the configured hostname and domain is the domain of the WMIC The username and password must be associated with an account on the FTP server If you are writing to the server the FTP server must be properly configured to accept your FTP write request Use the ip ftp username and ip ftp password commands to specify a username and password for all copies Include the username in the copy command if you want to specify only a username for that copy operation OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Fir
25. It shows the directory name in flash memory where the image is stored You can also use the dir filesystem privileged EXEC command to see the directory names of other software images you might have stored in flash memory Cisco 3200 Series Router Hardware Reference 718 E OL 5816 10 L Chapter 7 Managing Firmware and Configurations Working with Software Images lil tar File Format of Images on a Server or Cisco com Software images located on a server or downloaded from Cisco com are provided in a tar file format which contains these files amp info file The info file is always at the beginning of the tar file and contains information about the files within it TOS image Web management files needed by the HTTP server on the WMIC radio firmware 6500 img file info ver file The info ver file is always at the end of the tar file and contains the same information as the info file Because it is the last file in the tar file its existence means that all files in the image have been downloaded Note The tar file sometimes ends with an extension other than tar Copying Image Files by Using TFTP You can download an WMIC image from a TFTP server or upload the image from the WMIC to a TFTP server You download an WMIC image file from a server to upgrade the WMIC software You can overwrite the current image with the new one You upload an WMIC image file to a server for backup purposes this uploaded image
26. Protocol TFTP network server zflash Read only file decompression file system which mirrors the contents of the flash file system Setting the Default File System You can specify the file system or directory that the system uses as the default file system by using the cd filesystem privileged EXEC command You can set the default file system to omit the filesystem argument from related commands For example for all privileged EXEC commands that have the optional filesystem argument the system uses the file system specified by the cd command Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter7 Managing Firmware and Configurations Working with the Flash File System lil By default the default file system is flash You can display the current default file system as specified by the cd command by using the pwd privileged EXEC command Displaying Information About Files on a File System You can view a list of the contents of a file system before manipulating its contents For example before copying a new configuration file to flash memory you might want to verify that the file system does not already contain a configuration file with the same name Similarly before copying a flash configuration file to another location you might want to verify its filename for use in another command To display information about files on a file system use one of the privileged EXEC commands in Tabl
27. Secure Real time Transport Protocol SRTP 802 111 Internet Small Computer System Interface iSCSI and Internet Key Exchange IKE processing The security engine contains four crypto channels a controller and a set of crypto execution units EUs The security engine can act as a master on the internal bus This allows the security engine to alleviate the data movement bottleneck normally associated with slave only cores The host processor accesses the security engine through device drivers using system memory for data storage The security engine resides in the peripheral memory map of the processor therefore when an application requires cryptographic functions it simply creates descriptors for the security engine that define the cryptographic function to be performed and the location of the data The security engine bus mastering capability permits the host processor to set up a crypto channel with a few short register writes leaving the security engine to perform reads and writes on system memory Security Engine Features The execution units are e Public Key Execution Unit PKEU supporting the following RSA and Diffie Hellman Programmable field size up to 2048 bits Elliptic curve cryptography e Data Encryption Standard Execution Unit DEU DES 3DES Two key KI K2 or Three Key KI K2 K3 Electronic codebook ECB and cipher block chaining CBC modes for both DES and 3DES e Advanced Encryption Stand
28. Table 6 4 Differences Between WMICs continued Feature 2 4 GHz 802 11b g 4 9 GHz public safety 5 0 GHz 802 11h Comment Fast Roaming All scanning All scanning Fast roaming is not Scanning enhancements for faster enhancements for faster supported due to DFS Enhancements roaming are available roaming are available nature But normal except Use First Better roaming with scanning Access Point enhancement are available Simple Network Supported Supported for new values Supported The Management Protocol SNMP MIB IDs platform dependent SNMP code was modified to return new values entPhysical VendorT ype System OID and Chassis ID 2 4 GHz 802 11b g WMIC Features The key features of the 2 4 GHz 802 11b g WMIC are listed in Table 6 5 Table 6 5 Feature Description Key 2 4 GHz 802 11b g WMIC Features Data Rates Supported 1 2 5 5 6 9 11 12 18 24 36 48 and 54 Mbps Network Standard IEEE 802 11b and IEEE 802 11g Frequency Band 2 400 GHz to 2 497 GHz Modulation BPSK 1 Mbps and 6 Mbps QPSK 2 Mbps and 12 Mbps CCK 5 5 Mbps BPSK 9 6 Mbps CCK2 11 Mbps QPSK 18 Mbps 16 QAM 24 Mbps and 36 Mbps 64 QAM 48 Mbps and 54 Mbps Operating Channels North America 11 ETSI 13 Japan 14 Receive Sensitivitv 1 Mbps 94 dBm 2 Mbps 91 dBm 5 5 Mbps 89 dBm 11 Mbps 85 dBm Transmit Power Settings 100 mW 20 dBm 50 mW 17 dBm
29. W PCI connectors Mean Time Between Failure Differences Between WMICs Table 6 4 highlights the differences between WMICs The calculated Mean Time Between Failure MTBF exceeds of 1 190 136 hours Table 6 4 Differences Between WMICs Feature 2 4 GHz 802 11b g 4 9 GHz public safety 5 0 GHz 802 11h Comment Cookie and banner C3201 C3202 C3205 Frequencv 2 4 GHz 4 9 GHz 5 0 GHz Power Maximum Orthogonal Maximum OFDM power The power levels canbe Frequency Division Multiplexing OFDM power level is 15 dbm 30 mw but the power level might vary by country level is 17 dbm 50 mw defined as 4 dBm 7 dBm 10 dBm 13 dBm or 16 dBm Transmission Power Control TPC Not supported Not supported Supported for ETSI TPC limits the transmitted power to the minimum power level needed to reach the farthest user Dynamic Frequency Selection DFS Supported for ETSI DFS selects the radio channel most likely to minimize interference with military radar OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 6 Wireless Mobile Interface Cards a Table 6 4 Differences Between WMICs continued Feature 2 4 GHz 802 11b g 4 9 GHz public safety 5 0 GHz 802 11h Comment Channelization Statically declared as Channel width Statically declared as defined bv IEEE configured by using the jdefined by IEEE 802 11a
30. a Text Editor When creating a configuration file you must list commands logically so that the system can respond appropriately This is one method of creating a configuration file Step 1 Copy an existing configuration from a WMIC to a server For more information see the Downloading the Configuration File by Using TFTP section on page 7 10 the Downloading a Configuration File by Using FTP section on page 7 12 or the Downloading a Configuration File by Using RCP section on page 7 15 Step2 Open the configuration file in a text editor such as vi or emacs on UNIX or Notepad on a PC Step3 Extract the portion of the configuration file with the desired commands and save it in a new file Step4 Copy the configuration file to the appropriate server location For example copy the file to the TFTP directory on the workstation usually tftpboot on a UNIX workstation Step5 Make sure the permissions on the file are set to world read Copying Configuration Files by Using TFTP You can configure the WMIC by using configuration files you create download from another device or download from a TFTP server You can copy upload configuration files to a TFTP server for storage This section includes this information e Preparing to Download or Upload a Configuration File by Using TFTP page 7 9 e Downloading the Configuration File by Using TFTP page 7 10 e Uploading the Configuration File by Using TFTP page 7 11 Preparing t
31. and 13 5 Mbps 24 Mbps and 27 Mbps 48 Mbps and 54 Mbps Receive Sensitivity Table 6 10 shows the receive sensitivity for the 4 9 GHz WMIC Table 6 10 Receive Sensitivity for the 4 9 GHz WMIC 5 MHz 10 MHz 20 MHz 1 5 Mbps 89 dBm 3 Mbps 87 dBm 6 Mbps 85 dBm 2 25 Mbps 89 dBm 4 5 Mbps 87 dBm 9 Mbps 85 dBm 3 Mbps 89 dBm 6 Mbps 87 dBm 12 Mbps 85 dBm 4 5 Mbps 85 dBm 9 Mbps 87 dBm 18 Mbps 82 dBm 6 Mbps 82 dBm 12 Mbps 85 dBm 24 Mbps 79 dBm 9 Mbps 79 dBm 18 Mbps 79 dBm 36 Mbps 76 dBm 12 Mbps 74 dBm 24 Mbps 74 dBm 48 Mbps 71 dBm 13 5 Mbps 72 dBm 27 Mbps 72 dBm 54 Mbps 69 dBm Cisco 3200 Series Router Hardware Reference OL 5816 10 M 613 Chapter6 Wireless Mobile Interface Cards 5 0 GHz 802 11h Radio Features The 5 GHz radio supports only 20 MHz channelization In addition the 5 GHz radio supports Dynamic Frequency Selection DFS and Transmission Power Control TPC in the ETSI and FCC regulatory domains For more information about DFS and TPC see Radio Channels and Transmit Frequencies at http www cisco com en US products hw routers ps272 products_installation_and_configuration_guid es_list html amp Note 802 11h is supported only in the ETSI regulatory domain amp Note By default the C3205 WMIC uses the right antenna to receive and transmit data 5 0 GHz 802 11h Channels The 5 0 GHz 802 11h radio in the Cisco 3200 Series router currently available as the Cisco 3205 WMIC supports
32. and n is the port number Autonegotiation Disable To disable autonegotiation and Auto MDIX by forcing the line speed through a manual setting enter the following configuration commands Router config FastEthernet m n Router config if speed 10 or Router config FastEthernet m n Router config if speed 100 MAC Address Allocation The 4 port FESMIC stores 4 unique MAC addresses for the 10 100 Ethernet interfaces The 2 port FESMIC stores 2 unique MAC addresses for the 10 100 Ethernet interfaces In addition 37 MAC addresses are burned into Cisco 3270 Rugged Router card equipped routers and 33 MAC addresses are burned into the Mobile Access Router Card MARC to support the FESMIC per VLAN spanning tree PVST and inter VLAN routing features To provide support for up to 32 VLANs and the 32 Spanning Tree Protocol STP sessions that might be running 32 unique MAC addresses are required for the bridge packet data unit BPDU IDs In addition the FESMIC needs one MAC address for VLAN routing bringing the total of number of MAC addresses on the wired router to 34 To support future development the MAC addresses are burned into the Mobile Access Router Card MARC instead of the FESMIC Cisco 3200 Series Router Hardware Reference mm OL 5816 10 L Chapter 4 Fast Ethernet Switch Mobile Interface Card FESMIC Component Systems A The ISA buses and PCI buses on the Cisco 3200 Series Mobile Access Router cards prov
33. end caps and their indications Table 1 3 LEDs for Cisco 3230 Router I O End Caps LED Indication MARC Solid green OK Blinking Booting and self testing Black Not OK or the power is off Serial Status Link 1 status link LED per serial port Solid green Link OK Black No link is detected Amber blink Activity Fast Ethernet 2 LEDs per Fast Ethernet port Link LED Solid green Link OK Black No link is detected Activity LED Black No activity Green blink Activity WMIC Console Installation or Operation Mode For installation mode see Table 1 4 on page 1 19 For operation mode see Table 1 5 on page 1 20 WMIC Console LEDs WMIC console LEDs function in installation mode or operational mode The WMIC is set to the installation mode by default To change the function of the WMIC use the station role command Table 1 4 shows the status of the LEDs when the WMIC is in installation mode signal strength Table 1 4 WMIC Installation Mode RSSI dBm Status LED Radio LED gt 51 Steady Steady 58 to 54 Fast blinking 16 Hz Steady 60 to 57 Slow blinking 4 Hz Steady 63 to 60 Very slow blinking 2 Hz Steady 66 to 63 Black Steady 69 to 66 Black Fast blinking 16 Hz 72 to 69 Black Slow blinking 4 Hz 75 to 72 Black Very slow blinking 2 Hz lt 75 Black Black OL 5816 10 Cisco 3200 Series Router Hardware Refe
34. files in the directory and the directory are removed OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Software Images Uploading an Image File by Using TFTP You can upload an image from the WMIC to a TFTP server You can later download this image to the WMIC or to another WMIC of the same type A Caution For the download and upload algorithms to operate properly do not rename image directories Beginning in privileged EXEC mode follow these steps to upload an image to a TFTP server Command Purpose Step 1 Make sure the TFTP server is properly configured see the Preparing to Download or Upload an Image File by Using TFTP section on page 7 19 Step 1 Log in to the WMIC through a Telnet session Ste p2 archive upload sw Uploads the currently running WMIC image to the TFTP server tftp ocation directory image name tar e For location specify the IP address of the TFTP server e For directorylimage name tar specify the directory optional and the name of the software image to be uploaded Directory and image names are case sensitive The image name tar is the name of the software image to be stored on the server The archive upload sw privileged EXEC command builds an image file on the server by uploading these files in order info the IOS image the HTML files and info ver After these files are uploaded t
35. is forwarded again Use the storm control broadcast storm control multicast and storm control unicast global configuration commands to set up the storm control threshold value Storm Control Configuration This section describes how to configure storm control on your router It consists of the following configuration information and procedures e Enabling Storm Control e Verifying Storm Control By default unicast broadcast and multicast suppression is disabled on the switch Enabling Storm Control Enable storm control globally and enter the percentage of total available bandwidth that you want to be used by a all traffic multicast unitcast entering 100 percent would allow all traffic To enable a particular type of storm control use the following commands beginning in privileged EXEC mode Command Purpose Step1 Routert configure terminal Enters global configuration mode Step2 Router config no storm control Specifies the broadcast suppression level for an interface as a broadcast threshold lt 0 100 gt percentage of total bandwidth A threshold value of 100 percent means that no limit is placed on broadcast traffic Use the no keyword to restore the defaults Step3 Router config no storm control Specifies the multicast suppression level for an interface as a multicast threshold lt 0 100 gt percentage of total bandwidth Use the no keyword to restore the defaults Step4 Router conf
36. reception try to correct the interference by using one or more of the following measures e Turn the television or radio antenna until the interference stops e Move the equipment to one side or the other of the television or radio e Move the equipment farther away from the television or radio e Plug the equipment into an outlet that is on a different circuit from the television or radio That is make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses Modifications to this product not authorized by Cisco Systems Inc could void the FCC approval and negate your authority to operate the product The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California Berkeley UCB as part of UCB s public domain version of the UNIX operating system All rights reserved Copyright 1981 Regents of the University of California NOTWITHSTANDING ANY OTHER WARRANTY HEREIN ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS CISCO AND THE ABOVE NAMED SUPPLIERS DISCLAIM ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING USAGE OR TRADE PRACTICE IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES I
37. sw Uploads the currently running WMIC image to the RCP rep username Jlocation directorvjjlimage na server me tar e For username specify the username for the RCP copy request to execute an account must be defined on the network server for the remote username For more information see the Preparing to Download or Upload an Image File by Using RCP section on page 7 27 e For location specify the IP address of the RCP server e For directory image name tar specify the directory optional and the name of the software image to be uploaded Directory and image names are case sensitive e The image name tar is the name of software image to be stored on the server The archive upload sw privileged EXEC command builds an image file on the server by uploading these files in order info the IOS image the HTML files and info ver After these files are uploaded the upload algorithm creates the tar file format Cisco 3200 Series Router Hardware Reference OL 5816 10 a 731 Chapter 7 Managing Firmware and Configurations W Working with Software Images Cisco 3200 WMIC Image Upload Procedure Overview Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 This section provides the procedures for configuring a Cisco 3200 Series router referred to as the Mobile Access Router Card MARC as a TFTP server and uploading a Cisco IOS image to the router and two WMICs enclosed with the router The major
38. the configuration has been changed and not saved e For username password specify the username and password these must be associated with an account on the FTP server For more information see the Preparing to Download or Upload an Image File by Using FTP section on page 7 22 e For location specify the IP address of the FTP server e For directorvlimage name tar specify the directory optional and the image to download Directory and image names are case sensitive Step8 archive download sw leave old sw reload Downloads the image file from the FTP server to the WMIC ftp username password location directory and keep the current image limage name tar e The leave old sw option keeps the old software version after a download e The reload option reloads the system after downloading the image unless the configuration has been changed and not saved e For username password specify the username and password These must be associated with an account on the FTP server For more information see the Preparing to Download or Upload an Image File by Using FTP section on page 7 22 e For location specify the IP address of the FTP server e For directorvlimage name tar specify the directory optional and the image to download Directory and image names are case sensitive Note To avoid an unsuccessful download use the archive download sw safe command which downloads the im
39. the mounting bracket screws are from 58 to 68 in Ib Figure 1 12 shows the Cisco 3270 Rugged Enclosure mounting bracket Figure 1 12 Cisco 3270 Rugged Enclosure Mounting Bracket Cisco 3200 Series Router Hardware Reference OL 5816 10 KE Chapter1 Cisco 3200 Rugged Enclosures Figure 1 13 shows the dimensions of the Cisco 3270 Rugged Enclosure mounting bracket Figure 1 13 Cisco 3270 Rugged Enclosure Mounting Bracket Dimensions 2X B 406 20 TOOLING HOLE 4X 406 WIDE SLOT 1 TIT TIT TT T a chy 1 l dy r j 5 000 b 5 380 an it A F W L ot a a i 2x 281 THRU a FAR SIDE gt _ 3 900 3 9 nad 7 800 gt l 11 00 j 2x 9 976 6 850 015 EX 1 988 2x 51 25 7 a Era TAN H j H l l l l l H 4 12 H _ _ c i i l H H 2X R 20 2 00 N l I 232600 S 4X B 312 MI BOTH SIDES 2X R 156 BOTH SIDES Figure l 14 shows the Cisco 3230 Rugged Enclosure mounting bracket Figure 1 14 Cisco 3230 Rugged Enclosure Mounting Bracket 127452 Cisco 3200 Series Router Hardware Reference mm OL 5816 10 L Chapter 1 Cisco 3200 Rugged Enclosures Figure 1 15 shows the dimensions of the Cisco 3230 Rugged Enclosure mounting bracket Figure 1 15 Cisco 3230 Rugged Enclosure Mounting Brack
40. 2 3 fil VLAN1 2 3 VLANI 802 1 q Trunk Port connection mm Access Port connection P 7 8 I g The 802 1Q trunk port is used for VLAN extension from one switch to another 802 1Q capable switch and used for an 802 1Q capable router for inter VLAN routing The FESMIC supports both the VLAN extension and inter VLAN routing The 802 1Q uses an internal tagging mechanism Internal tagging means that a tag is inserted within the frame Note that on an 802 1Q trunk one VLAN is not tagged This VLAN named the native VLAN must be configured the same on each side of the trunk We can deduce to which VLAN a frame belongs when we receive a frame with no tag The EtherType field identifying the 802 1Q frame is 0x8100 In addition to the 12 bit VLAN ID 3 bits are reserved for 802 1P priority tagging as shown in Figure C 3 Also note that inserting a tag into a frame that already has the maximum Ethernet size creates a 1522 byte frame that can be considered a baby giant by the receiving equipment The FESMIC is capable of 802 1Q tagging only supporting 802 1Q trunking encapsulation It does not support the Cisco proprietary ISL encapsulation OL 5816 10 Cisco 3200 Series Router Hardware Reference E Appendix C Switch Port Functionality W Inter VLAN Routing Figure C 3 802 10 Tag Format in an Ethernet Frame Dest Src Len Etype Data Original Frame Tagged Dest Src
41. 36 0 48 0 54 0 rts threshold 4000 station role root ap only infrastructure client bridge group 1 bridge group 1 subscriber loop control bridge group 1 block unknown source no bridge group 1 source learning no bridge group 1 unicast flooding bridge group 1 spanning disabled 1 interface FastEthernet0 no ip address bridge group 1 no bridge group 1 source learning bridge group 1 spanning disabled no shutdown 1 interface BVIL ip address 10 10 10 3 255 255 255 0 no ip route cache 1 ip default gatewav 10 10 10 1 bridge 1 route ip 1 end Cisco 3200 Series Router Hardware Reference OL 5816 10 M 735 Chapter 7 Managing Firmware and Configurations W Working with Software Images Cisco 3200 Series Router Hardware Reference 736 l OL 5816 10 Step 1 Step 2 Step 3 Step 4 Step 5 APPENDIX A Smart Serial Port External Seal The Smart Serial port is not sealed When the Smart Serial port is not connected or otherwise in use the protective cover that is provided should be used to seal the port When a Smart Serial port is connected by means of a cable protective heat shrink tubing should be used to seal the port We recommend 4 1 shrink ratio tubing one piece is provided To seal the Smart Serial ports complete the following steps Cut a 1 8 inch length of heat shrink tubing If the Smart Serial port cable is attached remove it Feed the cable through the heat shrink tubing Secure the cable ba
42. 4 0 Serial 4 1 Serial 4 2 Serial 4 3 OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter5 Serial Mobile Interface Card 2 port SMIC Rotary Switch Positions Table 5 4 shows the 2 port SMIC serial signal assignments The position of the rotary switch determines the port assignments Although the rotary switch has 8 positions only 1 of 2 positions can be selected The rotary switch position should be unique for each mobile interface card MIC card Table 5 4 2 port SMIC Rotary Switch Positions and Serial Set Signal Assignments Rotary Switch Position MIC Slot Signal Assignments 0 1 Serial 1 0 Serial 1 1 Serial 1 2 Serial 1 3 1 2 Serial 2 0 Serial 2 1 Serial 2 2 Serial 2 3 SMIC LED Signals Table 5 5 shows the LED signals that are supported on the SMIC along with the corresponding functions Serial 2 and Serial 3 apply to the 4 port SMIC only Table 5 5 SMIC LED Functions LED Function SERIALO ACTIVITY Blinks once when a packet is either transmitted from or received on Serial 0 Originates from Header 5 SERIALO LINK Indicates the status of Serial 0 Originates from Header 5 The LED is on when a serial port is in DTE mode and when the data set ready DSR data carrier detect DCD and clear to send CTS signals are detected The LED is on when a serial port is in DCE mode and when the data terminal ready DTR and request to send RTS signals are detect
43. 7 Managing Firmware and Configurations W Working with Software Images Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Hl Cisco 3200 Series Router Hardware Reference Beginning in privileged EXEC mode follow Steps 1 through 7 to download a new image from an FTP server and overwrite the existing image To keep the current image skip Step 7 Command Purpose Verify that the FTP server is properly configured by referring to the Preparing to Download or Upload an Image File by Using FTP section on page 7 22 Log in to the WMIC through a Telnet session configure terminal Enters global configuration mode This step is required only if you override the default remote username or password see Steps 4 5 and 6 ip ftp username username Optional Changes the default remote username ip ftp password password Optional Changes the default password end Returns to privileged EXEC mode OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil Command Purpose Step7 archive download sw overwrite reload Downloads the image file from the FTP server to the WMIC ftp username password location directory and overwrite the current image limage name tar e The overwrite option overwrites the software image in flash with the downloaded image e The reload option reloads the system after downloading the image unless
44. 7130770 10 20 1 7 GigabitEthernet4 9 H 1385673757 34 10 25 1 GigabitEthernet4 10 H 0 34 10 11 1 30 FastEthernet6 26 H 0 0 10 37 11 FastEthernet6 37 H 0 0 T2233 84 FastEthernet6 47 H 514 68 Enter the show ip mroute count command Router show ip mroute count IP Multicast Statistics 56 routes using 28552 bytes of memory 13 groups 3 30 average sources per group Forwarding Counts Pkt Count Pkts per second Avg Pkt Size Kilobits per second Other counts Total RPF failed Other drops OIF null rate limit etc Group 224 2 136 89 Source count 1 Group pkt count 29051 Source 132 206 72 28 32 Forwarding 29051 278 1186 0 Other 85724 8 56665 Router Note Step 3 The tive counter means that the outgoing interface list of the corresponding entry is NULL and this indicates that this flow is still active Enter the show ip interface vlan 10 command Router show ip interface vlan 10 Vlan10 is up line protocol is up Internet address is 10 0 0 6 8 Broadcast address is 255 255 255 255 Address determined by non volatile memory MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined 224 0 0 1 224 0 0 2 224 0 0 13 224 0 0 10 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Security level is default Split horizon is enabled ICMP redirects are always sent OL 5816 10 Cisco 3200 Series Router Hardware Reference E
45. AN corresponds to the VLAN tag associated with data frames on an ISL or 802 1Q encapsulated trunk or the VLAN ID configured for an access port Configure a VLAN interface for each VLAN for which you want to route traffic and assign it an IP address SVIs support routing protocol and bridging configurations Creating a SVI Step 1 Step 2 Step 3 Step 4 To make any of the 2 port FESMIC or the 4 port FESMIC switchports routable do the following Create a VLAN ID that will be used for the VLAN From the enable prompt not the global configuration prompt enter the following commands Router vian database your prompt is now Router vlan Router vlan vlan 7 Router vlan exit amp Note If you skip Step 2 your switchport virtual interface line protocol will be down Go to global configuration mode and enter your switchport Router gt conf t Router interface FastEthernet3 0 Router config if switchport access vlan 7 Configure the IP address for the interface by entering the SVI Router config if interface configuration Router config if tinterface vlan 7 Router config if ip address 7 7 7 7 255 255 255 0 The 10 100 Fast Ethernet 3 0 switchport can be pinged by through the VLAN interface You can now attach any Layer 3 features to interface with the VLAN OL 5816 10 Cisco 3200 Series Router Hardware Reference E Appendix C Switch Port Functionality HIP Multicast Layer 3 Switchin
46. APPLY completed BRIELAQ eet Router VTP Version 2 Example The following example shows how to enable VTP version 2 Router vlan database Router vlan vtp v2 mode V2 mode enabled Router vlan exit APPLY completed Biting has Router The IEEE 802 1P specification defines eight levels of priority 0 thru 7 with priority 7 being the highest priority This information is carried in the 3 bit priority field of the VLAN tag header The FESMIC supports up to four class of service CoS queues per port For the tagged packets the incoming packet priority can be mapped into one of the four queues based on the priority field in the tag header or from the result of filtering mechanism For untagged packets the CoS priority is derived either from a programmable field within the ARL MAC address table or from the result of filtering mechanism After the packets are mapped into a CoS queue they are forwarded or conditioned using these scheduling algorithms e Strict priority based scheduling Any packets residing in the higher priority queues are transmitted first Only when these queues are empty will packets of lower priority be transmitted The disadvantage of this scheme is the potential starvation of packets in lower priority queues e Weighted round robin scheduling This scheme alleviates the starvation of packets in lower priority queues by providing a certain minimum bandwidth to all queues for transmission This ba
47. Afiafi CISCO Cisco 3200 Series Router Hardware Reference August 2008 Americas Headquarters Cisco Systems Inc 170 West Tasman Drive San Jose CA 95134 1706 USA http www cisco com Tel 408 526 4000 800 553 NETS 6387 Fax 408 527 0883 Text Part Number OL 5816 10 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE ALL STATEMENTS INFORMATION AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY The following information is for FCC compliance of Class A devices This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communi
48. CI bus pin D30 is removed and the D30 opening is plugged On the ISA bus pin C19 and pin B10 are removed and the C19 and B10 openings are plugged OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter2 Cisco 3270 Rugged Router Card Cisco 3270 Rugged Router Card Power Requirements The Cisco 3270 Rugged Router card uses 3 3 V 5 V and 12 V power sources Typical power consumption is 20 W The maximum calculated wattage is 26 5 W Table 2 1 Cisco 3270 Rugged Router Card Voltages Voltage Current Power 43 3 V 1 8 A 5 9 W 5 0 V 40A 20 0 W 12 0 V 0 05 A 0 6 W Power Connections AUX The speed of the AUX port for the Cisco 3270 Rugged Router card can be configured as 2400 4800 9600 19200 38400 57600 115200 230400 or 460800 bps Use the line aux linenumber speed command to modify the speed of the port A 5V power supply is provided for devices connected to the AUX port A Global Positioning System GPS modem is used as an example in this section Typically the 5V power supply current to GPS modems should be limited to less than 200 mA Table 2 2 shows the pin assignments for power on the AUX port Table 2 2 Cisco 3270 Rugged Router Card Multifunction Header Pin Assignments for Power Pin Signal Description Function 9 GND Ground GND 26 5 V 5 V DC Power Supply Power Hardware Encryption Processor The Cisco 3270 Rugged Router card integrated security e
49. Cisco 3200 rugged enclosures Cisco 3270 Rugged Router Card MAC Address Allocation Cisco 3270 Rugged Router card equipped routers are allocated 37 MAC addresses starting from the base MAC address A card equipped Cisco 3270 Rugged Router supports four interface ports Fast Ethernet ports can be port 0 and 1 Gigabit Ethernet ports are port 2 and 3 depending on the router configuration The assignments for MAC addresses are as follows e Four MAC addresses for each of the for four Ethernet ports offset 0 to 3 from the base MAC address e One switch virtual interface SVT for the FESMIC offset 4 from the base MAC address e Thirty two MAC addresses for FESMIC Spanning Tree Protocol STP offset 5 to 36 from the base MAC address Cisco 3200 Series Router Hardware Reference P28 E OL 5816 10 CHAPTER Mobile Access Router Card The Mobile Access Router Card is one component of the Cisco 3200 Series Mobile Access Router It includes the host processor memory and headers for the Fast Ethernet console and auxiliary signals for the router Additional components provide power and link interfaces to the MARC For example the 4 port Serial Mobile Interface Card SMIC provides up to four Smart Serial interfaces The exact configuration of your router will vary depending on how your vendor configured it Note A This section provides basic information about the MARC hardware for the purpose of performing simple troubl
50. Fast Ethernet port is never brought out to the end cap The WMIC console port is brought out to the corresponding RJ 45 port on the I O end cap replacing a Fast Ethernet port If the router includes one WMIC the RS 232 WMIC console port replaces a Fast Ethernet port on the end cap If the router includes two WMICs two WMIC EIA TIA 232 console ports replace two Fast Ethernet ports on the end cap Note At present even if the router contains zero WMICs in standard configurations a maximum of three Fast Ethernet ports are brought out to the end cap Unused EIA TIA 232 ports are sealed Fast Ethernet Signals on the WMIC amp The Fast Ethernet signals are delivered through a 10 pin header LED signals and EIA TIA 232 console signals are provided through the 24 pin multifunction header There is one set of fixed Fast Ethernet signals on the WMIC The Fast Ethernet port signals comply with IEEE 802 3 The signals are provided through the Ethernet headers which support the following e Autonegotiation for 10 100BASE TX connection e Full duplex and half duplex modes e Low power sleep mode e 10OBASE T and IOOBASE TX using a single Ethernet connection e Robust baseline wander correction performance e Standard carrier signal multiple access collision detect CSMA CD or full duplex operation e Integrated LED drivers Note If Auto MDIX is disabled when connecting to Ethernet switches or repeaters use a straight through cab
51. Fast Ethernet port on the MARC A Cisco router identifies a Fast Ethernet interface address by its slot number and port number in the format slot port The slot port address of a Fast Ethernet interface on the MARC is 0 0 The Fast Ethernet port signals are in compliance with IEEE 802 3 They are provided through the 10 pin Ethernet header which supports the following e Autonegotiation and parallel detection MII interface with extended register capability for 10 100BASE TX connection e Full duplex and half duplex modes e 3 3 V operation low power consumption 300 mW typical e Low power sleep mode e 1OBASE T and IOOBASE TX using a single Ethernet connection e Robust baseline wander correction performance e 100BASE FX fiber optic capabilities e Standard carrier signal multiple access collision detect CSMA CD or full duplex operation e Integrated programmable LED drivers The FastEthernet 0 0 port on the MARC is a Fast Ethernet router port The FastEthernet ports on the 4 port FESMIC and the 2 port FESMIC are Fast Ethernet switch ports The routing features supported on the MARC cannot be configured on the FESMIC ports Cisco 3200 Series Router Hardware Reference OL 5816 10 tM Chapter3 Mobile Access Router Card Console and Auxiliary Signals amp You can configure the console interface by using Cisco IOS command line interface CLI commands The console interface and the AUX port can be accessed simultaneously Als
52. IP address in a particular command than the existing configuration the IP address in the copied configuration is used However some commands in the existing configuration might not be replaced or negated In this case the resulting configuration file is a mixture of the existing configuration file and the copied configuration file with the copied configuration file having precedence To restore a configuration file to an exact copy of a file stored on a server copy the configuration file directly to the startup configuration by using the copy ftp rep tftp nvram startup config privileged EXEC command and reload the WMIC Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Configuration Files W Configuration File Types and Location Startup configuration files are used during system startup to configure the software Running configuration files contain the current configuration of the software The two configuration files can be different For example you might want to change the configuration for a short time period rather than permanently In this case you would change the running configuration but not save the configuration by using the copy running config startup config privileged EXEC command The running configuration is saved in DRAM the startup configuration is stored in the NVRAM section of flash memory Creating a Configuration File by Using
53. Information page 7 17 Guidelines for Creating and Using Configuration Files Creating configuration files can aid in your WMIC configuration Configuration files can contain some or all of the commands needed to configure one or more access points For example you might want to download the same configuration file to several access points that have the same hardware configuration Use these guidelines when creating a configuration file e If no passwords have been set on the WMIC you must set them on each bridge by entering the enable secret secret password global configuration command Enter a blank line for this command The password is saved in the configuration file as clear text e If passwords already exist you cannot enter the enable secret secret password global configuration command in the file because the password verification will fail If you enter a password in the configuration file the WMIC mistakenly attempts to execute the passwords as commands as it executes the file e The copy ftp rep tftp system running config privileged EXEC command loads the configuration files on the WMIC as if you were entering the commands at the command line The WMIC does not erase the existing running configuration before adding the commands If a command in the copied configuration file replaces a command in the existing configuration file the existing command is erased For example if the copied configuration file contains a different
54. NCLUDING WITHOUT LIMITATION LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES CCDE CCENT Cisco Eos Cisco Lumin Cisco Nexus Cisco StadiumVision Cisco TelePresence the Cisco logo DCE and Welcome to the Human Network are trademarks Changing the Way We Work Live Play and Learn and Cisco Store are service marks and Access Registrar Aironet AsyncOS Bringing the Meeting To You Catalyst CCDA CCDP CCIE CCIP CCNA CCNP CCSP CCVP Cisco the Cisco Certified Internetwork Expert logo Cisco IOS Cisco Press Cisco Systems Cisco Systems Capital the Cisco Systems logo Cisco Unity Collaboration Without Limitation EtherFast EtherSwitch Event Center Fast Step Follow Me Browsing FormShare GigaDrive HomeLink Internet Quotient IOS iPhone iQ Expertise the iQ logo iQ Net Readiness Scorecard iQuick Study IronPort the IronPort logo LightStream Linksys MediaTone MeetingPlace MeetingPlace Chime Sound MGX Networkers Networking Academy Network Registrar PCNow PIX PowerPanels ProConnect ScriptShare SenderBase SMARTnet Spectrum Expert StackWise The Fastest Way to Increase Your Internet Quotient TransPath WebEx and the WebEx logo are registered trademarks of Cisco Systems Inc and or its affiliates in the United States and certain other countries All other trademarks mentioned in this document
55. P server by using the ping command If you are accessing the WMIC through a Telnet session and you do not have a valid username make sure that the current RCP username is the one that you want to use for the RCP download You can enter the show users privileged EXEC command to view the valid username If you do not want to use this username create a new RCP username by using the ip remd remote username username global configuration command to be used during all archive operations The new username is stored in NVRAM If you are accessing the WMIC through a Telnet session and you have a valid username this username is used and there is no need to set the RCP username Include the username in the archive download sw or archive upload sw privileged EXEC command if you want to specify a username only for that operation When you upload an image to the RCP to the server it must be properly configured to accept the RCP write request from the user on the WMIC For UNIX systems you must add an entry to the thosts file for the remote user on the RCP server For example suppose the WMIC contains these configuration lines hostname apl ip rcmd remote username User0 If the WMIC IP address translates to ap1 company com the rhosts file for User0 on the RCP server should contain this line apl company com apl For more information refer to the documentation for your RCP server Cisco 3200 Series Router Hardware Reference OL 5816 10 Ch
56. RD I Received Source Specific Host Report Outgoing interface flags H Hardware switched Timers Uptime Expires Interface state Interface Next Hop or VCD State Mode 230 13 13 1 00 16 41 00 00 00 RP 10 15 1 20 flags SJC Incoming interface GigabitEthernet4 8 RPF nbr 10 15 1 20 Outgoing interface list GigabitEthernet4 9 Forward Sparse Dense 00 16 41 00 00 00 230 13 13 2 00 16 41 00 00 00 RP 10 15 1 20 flags SJC Incoming interface GigabitEthernet4 8 RPF nbr 10 15 1 20 Outgoing interface list GigabitEthernet4 9 Forward Sparse Dense 00 16 41 00 00 00 10 20 1 15 230 13 13 1 00 14 31 00 01 40 flags CJT Incoming interface GigabitEthernet4 8 RPF nbr 10 15 1 20 Outgoing interface list GigabitEthernet4 9 Forward Sparse Dense 00 14 31 00 00 00 Cisco 3200 Series Router Hardware Reference OL 5816 10 Appendix C Switch Port Functionality Storm Control li 132 206 72 28 224 2 136 89 00 14 31 00 01 40 flags CIJT Incoming interface GigabitEthernet4 8 RPF nbr 10 15 1 20 RPF MFD Outgoing interface list Null Router Note The RPF MFD flag indicates that the flow is completely hardware switched The H flag indicates that the flow is hardware switched on the outgoing interface Storm Control A packet storm occurs when a large number of broadcast unicast or multicast packets are received on a port Forwarding these packets can cause the network to slow down or t
57. This example shows how to configure the software from the file tokyo confg at IP address 172 16 2 155 bridge copy tftp 172 16 2 155 tokyo confg system running config Configure using tokyo confg from 172 16 2 155 confirm y Booting tokyo confg from 172 16 2 155 OK 874 16000 bytes Cisco 3200 Series Router Hardware Reference P7410 l OL 5816 10 L Chapter 7 Managing Firmware and Configurations Working with Configuration Files W Uploading the Configuration File by Using TFTP Step 1 Step 2 Step 3 To upload a configuration file from a WMIC to a TFTP server for storage follow these steps Verify that the TFTP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using TFTP section on page 7 9 Log in to the WMIC through a Telnet session Upload the WMIC configuration to the TFTP server Specify the IP address or hostname of the TFTP server and the destination filename Use one of these privileged EXEC commands e copy system running config tftp location directory filename e copy nvram startup config tftp location directory filename The file is uploaded to the TFTP server This example shows how to upload a configuration file from an WMIC to a TFTP server bridge copy system running config tftp 172 16 2 155 tokyo config Write file tokyo confg on host 172 16 2 155 confirm y Writing tokyo confg OK Copying Configuration
58. US products hw contnetw ps789 products_installation_guide_chapter09186a 00805f718d html Cisco 3200 Series Router Hardware Reference ie E OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures Console Port Signals You can connect to the router or to a Wireless Mobile Interface Card WMIC by using a console cable to connect to the console interfaces The console port signals e Are asynchronous serial DCE e Support 9 6 kbps 19 2 kbps 38 4 kbps 57 6 kbps and 115 2 kbps baud rates e Support full modem control of DTR DSR RTS and CTS signals AUX Port Signals The AUX port is a serial asynchronous port that supports the following speeds e Cisco 3270 Rugged Router card in the Cisco 3270 Router 1 2 kbps 2 4 kbps 4 8 kbps 9 6 kbps 19 2 kbps 38 4 kbps 57 6 kbps 115 2 kbps and 460 kbps e Mobile Access Router Card MARC in the Cisco 3230 Router 1 2 kbps 2 4 kbps 4 8 kbps 9 6 kbps 19 2 kbps 38 4 kbps 57 6 kbps and 115 2 kbps The AUX port supports the following e Asynchronous serial DTE e 5 to 8 data bits e 1 1 5 or 2 stop bits e Odd even or no parity e Flow control by using RTS CTS DTR and CDC signals Cisco 3200 Series Router Hardware Reference OL 5816 10 SIKEM Chapter 1 Cisco 3200 Rugged Enclosure LED Indications This section describes the LED indications for the Cisco 3200 Rugged Enclosure I O end caps amp Note The behavior of the WMIC LEDs is described in the WMIC Con
59. a Telnet session Cisco 3200 Series Router Hardware Reference OL 5816 10 L Chapter7 Managing Firmware and Configurations Working with Software Images lill Command Purpose Step3 archive download sw overwrite reload Downloads the image file from the TFTP server to the WMIC and tftp location directory image name overwrite the current image e The overwrite option overwrites the software image in flash with the downloaded image e The reload option reloads the system after downloading the image unless the configuration has been changed and not saved e For location specify the IP address of the TFTP server e Fordirectorvlimage name specify the directory optional and the image to download Directory and image names are case sensitive Step4 archive download sw leave old sw reload Downloads the image file from the TFTP server to the WMIC and tftp location directory image name keep the current image e The leave old sw option keeps the old software version after a download e The reload option reloads the system after downloading the image unless the configuration has been changed and not saved e For location specify the IP address of the TFTP server e For directory image name specify the directory optional and the image to download Directory and image names are case sensitive Note To avoid an unsuccessful download use the archive download sw safe comma
60. a technical support representative Cisco 3200 Series Router Hardware Reference OL 5816 10 Appendix B SFP Module Replacement Error Message NOT IDENTIFIED Detected for transceiver module in s module disabled Explanation The transceiver module for the interface specified in the error message could not be identified and mav not be compatible with the interface The transceiver module specified in the error message contains a transceiver code which could not be correctly interpreted As a result of the error the module is disabled Recommended Action Replace the module with a compatible transceiver Error Message UNSUPPORTED TRANCEIVER Unsupported SFP transceiver found on board Warranty support may void Explanation The transceiver module for the interface specified in the error message is not a Cisco supported module As a result of the error the module is disabled When Cisco determines that a fault or defect can be traced to the use of third party transceivers installed by a customer or reseller then at Cisco s discretion Cisco may withhold support under warranty or a Cisco support program In the course of providing support for a Cisco networking product Cisco might require that the end user install Cisco transceivers if Cisco determines that removing third party parts will assist Cisco in diagnosing the cause of a support issue Recommended Action None OL 5816 10 Cisco 3200 Series Router Ha
61. ader Green Green DRAM memorv test status Amber Red Board initialization test Blinking Blinking Flash memory test green green Amber Green Ethernet initialization test Green Green Green Starting Cisco IOS software Association Green At least one wireless client device is status associated with the unit Blinking No client devices are associated check the green wireless device service set identifier SSID and Wired Equivalent Privacy WEP settings Operating Green Blinking Transmitting receiving radio packets status green Green Ethernet link is operational Blinking Transmitting receiving Ethernet packets green Boot Loader Red Red DRAM memory test failure Errors Red Red File system failure Red Red Ethernet failure during image recovery Amber Green Amber Boot environment error Red Green Red No Cisco IOS image file Amber Amber Amber Boot failure Cisco 3200 Series Router Hardware Reference mem OL 5816 10 Chapter6 Wireless Mobile Interface Cards a Table 6 1 Indicator Signals continued Message Ethernet Status Radio Type Indicator Indicator Indicator Meaning Operation Green Blinking Maximum retries or buffer full occurred on Errors amber the radio Blinking Transmit receive Ethernet errors amber Blinking General warning amber Configuration Amber Resetting the configu
62. adio channel spacing radio channel or frequency and Dynamic Frequency Selection DFS e Roles and the Associations of Wireless Devices OL 11494 03 Description of the roles Cisco wireless devices can be assigned and how the role of a device affects its ability to associate or not associate with other wireless devices e Cisco 3200 Series Wireless MIC Software Configuration Guide OL 6415 05 Provides sample procedures for using the IOS commands to configure Wireless Mobile Interface Cards WMICs e Cisco 3200 Series Mobile Access Router Software Configuration Guide OL 1926 06 Provides sample procedures for using the Cisco IOS commands to configure the Cisco 3270 Rugged Router card or the Mobile Access Router Card MARC in Cisco 3200 Series routers e Cisco 3200 Series Mobile Access Router Hardware Reference OL 5816 This book Provides descriptions of the Cisco MIC I O cards in the Cisco 3200 Series routers e Cisco 3200 Series Mobile Access Router Reference Sell Document OL 3880 Presents an overview of the reference sell program and components for the Cisco 3200 Series router e Regulatory Compliance and Safety Information for the Cisco 3200 Mobile Access Router 78 16930 Provides regulatory compliance and safety information The release notes that list the enhancements to and caveats for Cisco IOS releases that pertain to the Cisco 3200 Series router are available at http www cisco com en US products sw iosswrel p
63. advantage of this procedure is that all the cards in the router receive the same version of the Cisco IOS image to avoid conflicts when the devices communicate The Cisco 3200 Series router is actually a stack of devices contained in an enclosure that can include multiple devices that process data from the network independently For example a Cisco 3200 Series router with two WMICs is actually three devices in one enclosure one router consisting of a MARC and possibly a Fast Ethernet Switch Mobile Interface Card FESMIC and or a Serial Mobile Interface Card SMIC and two WMICS The MARC communicates with a FESMIC or a SMIC through the internal PCI bus The FESMIC and the SMIC depend on the MARC to process the data that the FESMIC or SMIC send and receive As a result FESMIC and SMIC cards are seen by the MARC as expansion cards similar to the way in which a modular Cisco router increases functionality with the addition of expansion modules The cards physically and logically become part of the router Each WMIC has an on board CPU that processes data it sends and receives independent of the MARC The WMICs draw power from the internal bus they do not use the bus to communicate with the other devices in the stack The WMICs communicate with the router by using the switched Fast Ethernet ports and the routed Fast Ethernet port to create a small internal Ethernet network As a result each WMIC must store a copy of the Cisco IOS image in its memo
64. age first and does not delete the current running version until the download succeeds The download algorithm verifies that the image is appropriate for the WMIC model and that enough DRAM is present or it aborts the process and reports an error If you specify the overwrite option the download algorithm removes the existing image on the flash device whether or not it is the same as the new one downloads the new image and then reloads the software Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version you must specify the overwrite option OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Software Images If you specify the leave old sw the existing files are not removed If there is not enough space to install the new image and keep the running image the download process stops and an error message is displayed The algorithm installs the downloaded image onto the system board flash device flash The image is placed into a new directory named with the software version string and the BOOT path list is updated to point to the newly installed image Use the privileged EXEC mode show boot command to display boot attributes and use the global configuration boot command to change the boot attributes If you kept the old image during the download process you speci
65. al bridge By copying the file to the new bridge you can change the relevant parts rather than recreating the whole file OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Configuration Files e To load the same configuration commands on all the access points in your network so that all the access points have similar configurations You can copy upload configuration files from the WMIC to a file server by using TFTP FTP or RCP You might perform this task to back up a current configuration file to a server before changing its contents so that you can later restore the original configuration file from the server The protocol you use depends on which type of server you are using The FTP and RCP transport mechanisms provide faster performance and more reliable delivery of data than TFTP These improvements are possible because FTP and RCP are built on and use the Transmission Control Protocol Internet Protocol TCP IP stack which is connection oriented This section includes this information e Guidelines for Creating and Using Configuration Files page 7 8 e Configuration File Types and Location page 7 9 e Creating a Configuration File by Using a Text Editor page 7 9 e Copying Configuration Files by Using TFTP page 7 9 e Copying Configuration Files by Using FTP page 7 11 e Copying Configuration Files by Using RCP page 7 14 e Clearing Configuration
66. allows you to configure the device over a Layer 3 protocol by using SNMP or a Telnet application This is referred to as the management VLAN for the switch The default management VLAN is usually the native VLAN 1 The configurable VLAN device allows you to configure any VLAN to be the management VLAN but there can be only one virtual Layer 3 interface in one VLAN A switch routing module like the FESMIC allows you to use the SVI to configure more than one virtual Layer 3 interface to support routing between the different VLANs and the virtual Layer 3 interface of any other router interface in the system as shown in Figure C 5 You can manage the switching router with any switch virtual Layer 3 interface created in the system The FESMIC router switch port is an interface capable of handling Layer 3 switching functionality in hardware The SVI architecture has the framework to support such a functionality e A SVI represents a VLAN of switch ports as one interface to the routing function in the system e There is at most one SVI associated with a VLAN e Itis not necessary to configure an SVI for every known VLAN It is only necessary to configure a SVI when you want to route between VLANs or want to provide IP host connectivity to the rest of the network by using any of the mobile access router routed interfaces e One management SVI interface VLAN 1 is created at system initialization to permit remote administration Additional SVIs exist on
67. and Configurations This chapter describes how to manipulate the flash file system how to copy configuration files and how to archive upload and download software images It consists of these sections e Working with the Flash File System page 7 1 e Working with Configuration Files page 7 7 e Working with Software Images page 7 18 Working with the Flash File System The flash file system on your WMIC provides several commands to help you manage software image and configuration files The flash file system is a single flash device on which you can store files This flash device is called flash This section provides information on the following topics e Displaying Available File Systems page 7 1 e Setting the Default File System page 7 2 e Displaying Information About Files on a File System page 7 3 e Changing Directories and Displaying the Working Directory page 7 3 e Creating and Removing Directories page 7 3 e Copying Files page 7 4 e Deleting Files page 7 5 e Creating Displaying and Extracting tar Files page 7 5 e Displaying the Contents of a File page 7 7 Displaying Available File Systems To display the available file systems on your WMIC use the show file systems command as shown in this example bridge show file systems File Systems Size b Free b Type Flags Prefixes OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter7 Managing Firmware and Configurations W Working w
68. and bottom This provides a non pooling surface in case the enclosure is exposed to water Maximum heat dissipation Thermally conductive pads and thermal vias around the board perimeter of each card physically contact thermal plates that physically contact the aluminum chassis This minimizes the overall board thermal rise by transferring heat into the surrounding environment The Cisco 3200 Rugged Enclosures are available as A fully assembled Cisco 3270 Rugged Enclosure that supports the Cisco 3270 Rugged Router card up to five mobile interface cards and one Cisco Mobile Router Power Card MRPC A fully assembled Cisco 3230 Rugged Enclosure that supports the Mobile Access Router Card MARC up to five mobile interface cards MICs and one MRPC OL 5816 10 Cisco 3200 Series Router Hardware Reference lii Chapter1 Cisco 3200 Rugged Enclosures Figure 1 1 shows an exploded view of a Cisco 3230 Rugged Enclosure The design of the longer Cisco 3270 Rugged Enclosure is similar Figure 1 1 Exploded View of a Rugged Enclosure 270439 1 T O end cap 2 Wiring card 3 Card stack 4 Extrusion body of the enclosure 5 Antenna end cap 1 This end cap shows four serial ports but the typical configuration has two serial ports The enclosures are sealed by using O rings between the extrusion and the end caps Cisco 3200 Series Router Hardware Reference mem OL 5816 10 Chapter1 Cisco 3200 Ru
69. and certain other countries All other trademarks mentioned in this document or Website are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 0805R Any Internet Protocol IP addresses used in this document are not intended to be actual addresses Any examples command display output and figures included in the document are shown for illustrative purposes only Any use of actual IP addresses in illustrative content is unintentional and coincidental 2008 Cisco Systems Inc All rights reserved 3 Printed in the USA on recycled paper containing 10 postconsumer waste Cisco 3200 Series Router Hardware Reference ca OL 5816 10 Numerics 2 4 GHz 802 11b g WMIC 6 1 3rd party devices 3 3 4 9 GHz public safety WMIC 6 1 5 0 GHz public safety WMIC 6 1 802 11a 6 13 802 11b g 6 11 802 11i 2 7 802 1D 4 1 802 1P 4 1 802 1Q 4 1 A Advanced Encryption Standard Unit AESU 2 5 2 7 antenna 6 2 connector type RP TNC 1 7 endcap 1 7 ARC Four execution unit AFEU 2 5 2 7 asynchronous AUX 1 17 3 1 3 4 baud rates 1 17 3 4 DTE 1 17 3 4 GPS 3 1 audience viii auto detection 1 16 Auto MDIX 4 1 4 2 6 3 auto negotiation 3 1 4 2 6 3 Zeroization 2 5 3 1 bridge packet data unit BPDU 4 2 bridging 4 1 broadcast kev rotation 6 6 bus communication 2 2 4 3 5 1 6 1 bus keying feature 2 3 3 2 4 4
70. and during all copy operations The new username is stored in NVRAM If you are accessing the WMIC through a Telnet session and you have a valid username this username is used and you do not need to set the FTP username Include the username in the copy command if you want to specify a username for only that copy operation e When you upload a configuration file to the FTP server it must be properly configured to accept the write request from the user on the WMIC For more information refer to the documentation for your FTP server Downloading a Configuration File by Using FTP To download a configuration file by using FTP follow these steps beginning in privileged EXEC mode Command Purpose Step 1 Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using RCP section on page 7 15 Step 2 Log in to the WMIC through a Telnet session Step1 configure terminal Enters global configuration mode on the WMIC This step is required only if you override the default remote username or password see Steps 4 5 and 6 Step2 ip ftp username username Optional Changes the default remote username Step3 ip ftp password password Optional Changes the default password Cisco 3200 Series Router Hardware Reference P72 E OL 5816 10 L Chapter 7 Managing Firmware and Configurations Working with Configuration Files W Comma
71. anv of the signals The PCI bus signals allow the Cisco SMIC and FESMIC to communicate with the Cisco 3270 Rugged Router card The WMIC draws power from the bus but it does not communicate with the router through the buses It communicates with the router through an internal Fast Ethernet port Non Cisco cards cannot communicate with the router over the PCI bus Caution If vou add non Cisco cards that generate signals on the PCI bus the router might shut down Please do not add non Cisco cards that generate signals on the PCI bus Cisco 3200 Series Router Hardware Reference mm OL 5816 10 Chapter2 Cisco 3270 Rugged Router Card Figure 2 1 shows the Cisco 3270 Rugged Router card header and bus locations Figure 2 1 Gigabit Ethernet fiber optic or copper Cisco 3270 Rugged Router Card Header and Bus Locations Gigabit Ethernet 0 Fast Ethernet 1 USB ports and USB LEDs PCI bus for future expansion ISA bus 2 4 Fast Ethernet 0 6 8 Jumper for optional Fast Ethernet 0 1 3 5 7 9 Optional Fast Ethernet 0 10 Multifunction AUX console LED header 11 GPIO Zeroization pins and USB header 12 PCI bus 1 Factory set Do not modify 2 General Purpose Input Output amp Note The PC 104 Plus standard requires that the PCI bus and the ISA bus use keying features in the standard stacking headers to guarantee proper module installation On the P
72. apter7 Managing Firmware and Configurations Working with Software Images lil Downloading an Image File bv Using RCP Xou can download a new image file and replace or keep the current image A Caution For the download and upload algorithms to operate properly do not rename image directories Beginning in privileged EXEC mode follow Steps 1 through 6 to download a new image from an RCP server and overwrite the existing image To keep the current image skip Step 6 Command Purpose Step 1 Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload an Image File by Using RCP section on page 7 27 Step 2 Log in to the WMIC through a Telnet session Step3 configure terminal Enters global configuration mode This step is required only if you override the default remote username see Steps 4 and 5 Step4 ip remd remote username username Optional Specifies the remote username Step5 end Returns to privileged EXEC mode Step6 archive download sw overwrite reload Downloads the image file from the RCP server to the rep username location directory limage na WMIC and overwrite the current image me tarl e The overwrite option overwrites the software image in flash with the downloaded image e The reload option reloads the system after downloading the image unless the configuration has been changed and not saved e For username specify the
73. ard Unit AESU Implements the Rinjdael symmetric key cipher Key lengths of 128 192 and 256 bits ECB CBC Counter with CBC MAC CCM and Counter modes e ARC Four execution unit AFEU Implements a stream cipher compatible with the RC4 algorithm 40 to 128 bit programmable key e Message Digest Execution Unit MDEU SHA 1 with 160 bit or 256 bit message digest MDS with 128 bit message digest Keyed Hash Message Authentication Code HMAC with either SHA or MD5 algorithm HMAC MD5 or HMAC SHA e Random Number Generator RNG OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter2 Cisco 3270 Rugged Router Card e 4 crypto channels each supporting multicommand descriptor chains Static and or dynamic assignment of crypto execution units through an integrated controller Buffer size of 256 bytes for each execution unit with flow control for large data sizes e 256 PBGA 17x17 in typical power 1 7 W Temperature Sensor A router equipped with the Cisco 3270 Rugged Router card includes a high precision digital thermometer and thermostat DS1631 The temperature is sampled every 30 seconds A warning is sent to users by means of SNMP traps and by flashing the overtemperature LED if temperature falls below 40 C or exceeds 95 C until the temperature falls back to its normal range Note The signal and LED are available only on the Cisco 3270 Rugged Router card not on the
74. atile store configured from host2 config by rcp from 172 16 101 101 Uploading a Configuration File by Using RCP To upload a configuration file by using RCP follow these steps beginning in privileged EXEC mode E Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Configuration Files W Command Purpose Step 1 Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using RCP section on page 7 15 Step 2 Log in to the WMIC through a Telnet session Step3 configure terminal Enters global configuration mode This step is required only if you override the default remote username see Steps 4 and 5 Step4 ip remd remote username username Optional Specifies the remote username Step5 end Returns to privileged EXEC mode Step6 copy system running config Using RCP copies the configuration file from an WMIC rep username location directory filename running or startup configuration file to a network server or copy nvram startup config rep username location directory filename This example shows how to copy the running configuration file named ap2 confg to the netadminl directory on the remote host with an IP address of 172 16 101 101 bridge copy system running config rcp netadmin1 172 16 101 101 ap2 confg Write file br confg on
75. can be used for future downloads to the same or another device of the same type This section includes this information Preparing to Download or Upload an Image File by Using TFTP page 7 19 Downloading an Image File by Using TFTP page 7 20 Uploading an Image File by Using TFTP page 7 22 Preparing to Download or Upload an Image File by Using TFTP Before you begin downloading or uploading an image file by using TFTP perform these tasks Ensure that the workstation acting as the TFTP server is properly configured On a Sun workstation make sure that the etc inetd conf file contains this line tftp dgram udp wait root usr etc in tftpd in tftpd p s tftpboot Make sure that the etc services file contains this line tftp 69 udp OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Software Images amp Note You must restart the inetd daemon after modifying the etc inetd conf and etc services files To restart the daemon either stop the inetd process and restart it or enter a fastboot command on the SunOS 4 x or a reboot command on Solaris 2 x or SunOS 5 x For more information on the TFTP daemon refer to the documentation for your workstation e Ensure that the WMIC has a route to the TFTP server The WMIC and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets Check connecti
76. cations Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense The following information is for FCC compliance of Class B devices The equipment described in this manual generates and may radiate radio frequency energy If it is not installed in accordance with Cisco s installation instructions it may cause interference with radio and television reception This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules These specifications are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation Modifying the equipment without Cisco s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices In that event your right to use the equipment may be limited by FCC regulations and you may be required to correct any interference to radio or television communications at your own expense You can determine whether your equipment is causing interference by turning it off If the interference stops it was probably caused by the Cisco equipment or one of its peripheral devices If the equipment causes interference to radio or television
77. ck onto the Smart Serial port by using the jack screws of the cable assembly as shown in Figure A 1 Figure A 1 Securing the Smart Serial Port Cable 270448 Move and secure adjacent port protectors away from the smart serial port OL 5816 10 Cisco 3200 Series Router Hardware Reference Appendix A Smart Serial Port External Seal Position the heat shrink tubing as shown in Figure A 2 so that one end is over the cable molding over the chassis protrusion and abuts the end cap Step 6 Positioning the Heat Shrink Tubing Over the Cable Molding Figure A 2 JU 6vvozz ii WA D TRS B Gn 5 m S Cisco 3200 Series Router Hardware Reference OL 5816 10 Appendix A Smart Serial Port External Seal Step 7 Apply heat by using a heat gun Heat the tubing until it is reduced in size and fits snugly over the chassis protrusion of the smart serial port Once it is secure direct the heat toward the other end of the tubing to shrink it against the cable molding as shown in Figure A 3 Figure A 3 Applying Heat to the Heat Shrink Tubing OL 5816 10 Cisco 3200 Series Router Hardware Reference E Appendix A Smart Serial Port External Seal Cisco 3200 Series Router Hardware Reference mem OL 5816 10 APPENDIX B SFP Module Replacement This chapter describes how to replace small form factor pluggable SFP modules SFP m
78. co 3200 Series Router Hardware Reference 7 32 OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil Configuration Example for the MARC hostname MAR 1 ip routing interface FastEthernet0 0 ip address 20 20 20 1 255 255 255 0 1 interface FastEthernet2 0 no ip address shutdown 1 interface FastEthernet2 1 no ip address shutdown 1 interface FastEthernet2 2 no ip address no shutdown 1 interface FastEthernet2 3 no ip address no shutdown 1 interface Vlanl ip address 10 10 10 1 255 255 255 0 no shutdown 1 tftp server flash c3202 k9w7 tar 1 end Fast Ethernet 0 0 WMIC Configuration Example Configuration hostname MAR1 AP 1 bridge irb 1 interface Dot11Radio0 no ip address no ip route cache no shutdown 1 ssid tsunami authentication open infrastructure ssid 1 cca 0 speed basic 1 0 basic 2 0 basic 5 5 6 0 9 0 basic 11 0 12 0 18 0 24 0 36 0 48 0 54 0 rts threshold 4000 station role workgroup bridge infrastructure client bridge group 1 bridge group 1 subscriber loop control bridge group 1 block unknown source no bridge group 1 source learning no bridge group 1 unicast flooding bridge group 1 spanning disabled Cisco 3200 Series Router Hardware Reference OL 5816 10 a 733 Chapter 7 Managing Firmware and Configurations W Working with Software Images interface FastEthernet0 no ip address bridge group 1 no bridge gr
79. ction header s The position of the rotary switch determines the port assignments Although the rotary switch has eight positions only positions 0 1 and 2 are supported on the 4 port SMIC and only positions 0 and 1 are supported on the 2 port SMIC Table 5 1 provides 4 port SMIC port assignments Table 5 1 4 port SMIC Rotary Switch Settings and Port Assignments Position MIC Slot Port Assignments 0 1 Serial 1 0 Serial 1 1 Serial 1 2 Serial 1 3 1 2 Serial 2 0 Serial 2 1 Serial 2 2 Serial 2 3 2 3 Serial 3 0 Serial 3 1 Serial 3 2 Serial 3 3 Table 5 2 provides the 2 port SMIC port assignments Table 5 2 2 port SMIC Rotary Switch Settings and Port Assignments Position MIC Slot Port Assignments 0 1 Serial 1 0 Serial 1 1 1 2 Serial 2 0 Serial 2 1 4 Port SMIC Rotary Switch Positions Table 5 3 shows the 4 port SMIC serial signal assignments The position of the rotary switch determines the port assignments Although the rotary switch has 8 positions only 1 of 4 positions can be selected The rotary switch position should be unique for each mobile interface card MIC card Table 5 3 4 port SMIC Rotary Switch Positions and Serial Set Signal Assignments Rotary Switch Position MIC Slot Signal Assignments 0 1 Serial 1 0 Serial 1 1 Serial 1 2 Serial 1 3 1 2 Serial 2 0 Serial 2 1 Serial 2 2 Serial 2 3 2 3 Serial 3 0 Serial 3 1 Serial 3 2 Serial 3 3 3 4 Serial
80. e 7 2 Table 7 2 Commands for Displaying Information About Files Command Description dir all filesystem filename Displays a list of files on a file system show file systems Displays more information about each of the files on a file system show file information file url Displays information about a specific file show file descriptors Displays a list of open file descriptors File descriptors are the internal representations of open files You can use this command to see if another user has a file open Changing Directories and Displaying the Working Directory To change directories and display the working directory follow these steps beginning in privileged EXEC mode Command Purpose Step1 dir filesystem Displavs the directories on the specified file svstem For filesvstem use flash for the svstem board flash device Step2 cdnew configs Changes to the directorv of interest The command example shows how to change to the directorv named new configs Step3 pwd Displays the working directory Creating and Removing Directories Beginning in privileged EXEC mode follow these steps to create and remove a directory Cisco 3200 Series Router Hardware Reference OL 5816 10 73 Chapter 7 Managing Firmware and Configurations W Working with the Flash File System Command Purpose Step1 dir filesystem Displays the directories on the specified file system For filesystem use flash for the
81. e Serial Mobile Interface Card SMIC and FESMIC communicate with the router through the bus All the router Fast Ethernet ports are addressed by using the slot port format In typical configurations the first WMIC Fast Ethernet port is connected to the routed Fast Ethernet port on the router card The Fast Ethernet ports of the second and third WMICs are connected to FESMIC switched Fast Ethernet ports The differences in the types of the router Fast Ethernet ports that the WMICs are connected to affect how they are configured as for example when uploading a Cisco IOS image to a WMIC The WMIC runs an independent Cisco IOS image and when you configure the WMIC the link forms an internal LAN In standard configurations the WMIC Fast Ethernet port is never brought out to the end cap The WMIC console port is brought out to the corresponding RJ 45 port on the I O end cap replacing a Fast Ethernet port If the router includes one WMIC the EIA TIA 232 WMIC console port replaces a Fast Ethernet port on the end cap If the router includes two WMICs two WMIC EIA TIA 232 console ports replace two Fast Ethernet ports on the end cap Note At present even if the router contains no WMICs in standard configurations the maximum three Fast Ethernet ports are brought out to the end cap Unused EIA TIA 232 ports are sealed Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures
82. eal the fiber optic port when it is connected to a cable use connectors that maintain IP 67 integrity The part numbers for the connectors are Tyco 1828618 1 and Tyco 1828618 2 A Caution When connecting fiber optic cables observe all standard procedures for safety and maintain a clean connection Power Connector IP 67 Integrity To seal the Tyco DC Power input power connector and maintain IP 67 integrity use the following parts e 796094 2 CPC housing e 66101 3 contact e 207489 1 boot e 207490 1 cable grip size 11 Smart Serial Port External Seal for System Integrity When the Smart Serial port is not connected or otherwise in use the protective cover should be used to seal the port To seal the Smart Serial port when the port is connected to a cable complete the steps in Appendix A Smart Serial Port External Seal in the Cisco 3200 Series Router Hardware Reference Cisco 3200 Series Router Hardware Reference i10 OL 5816 10 L Chapter 1 Cisco 3200 Rugged Enclosures USB Flash Storage Device Caveat In some cases using two USB flash storage devices causes unpredictable results CSCsd11136 If one USB flash storage device is plugged into a USB port and a second USB flash storage device is plugged into or unplugged from the other port an error might occur CSCsd44152 The error message is USB_HOST_STACK 6 USB_FLASH_READY_TEST_TIME USB flash Readw test time over 4 seconds If an unsuppor
83. eate destination url flash file url For destination url specify the destination URL alias for the local or network file system and the name of the tar file to create These options are supported e For the local flash file system the syntax is flash file url e For the File Transfer Protocol FTP the syntax is ftp username password location directory tar filename tar e For the Remote Copy Protocol RCP the syntax is rep username location directory tar filename tar e For the Trivial File Transfer Protocol TFTP the syntax is tftp location directory tar filename tar The tar filename tar is the tar file to be created OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with the Flash File System For flash file url specify the location on the local flash file system from which the new tar file is created You can also specify an optional list of files or directories within the source directory to write to the new tar file If none are specified all files and directories at this level are written to the newly created tar file This example shows how to create a tar file This command writes the contents of the new configs directory on the local flash device to a file named saved tar on the TFTP server at 172 20 10 30 bridge archive tar create tftp 172 20 10 30 saved tar flash new configs Displaying the Contents of a
84. ed SERIALI ACTIVITY Blinks once when a packet is either transmitted from or received on Serial 1 Originates from Header 5 SERIAL1 LINK Indicates the status of Serial 1 Originates from Header 5 The LED is on when the serial port is in DTE mode and when the DSR DCD and CTS signals are detected The LED is on when the serial port is in DCE mode and when the DTR and RTS signals have been detected SERIAL2 ACTIVITY Blinks once when a packet is either transmitted from or received on Serial 2 Originates from Header 2 SERIAL2 LINK Indicates the status of Serial 2 Originates from Header 2 The LED is on when the serial port is in DTE mode and when the DSR DCD and CTS signals are detected The LED is on when the serial port is in DCE mode and when the DTR and RTS signals have been detected SERIAL3 ACTIVITY Blinks once when a packet is either transmitted FROM or received on Serial 3 Originates from Header 2 SERIAL3 LINK Indicates the status of Serial 3 originates from Header 2 The LED is on when the serial port is in DTE mode and when the DSR DCD and CTS signals are detected The LED is on when the serial port is in DCE mode and when the DTR and RTS signals have been detected Cisco 3200 Series Router Hardware Reference mm OL 5816 10 Chapter Serial Mobile Interface Card SMIC Power Consumption The SMIC draws power from the PCI and the ISA connectors Table 5 6 shows the estima
85. emote username This section includes this information Preparing to Download or Upload a Configuration File by Using RCP page 7 15 Downloading a Configuration File by Using RCP page 7 15 Uploading a Configuration File by Using RCP page 7 16 Preparing to Download or Upload a Configuration File by Using RCP Before you begin downloading or uploading a configuration file by using RCP perform these tasks Ensure that the workstation acting as the RCP server supports the remote shell rsh Ensure that the WMIC has a route to the RCP server The WMIC and the server must be in the same subnetwork if you do not have a router to route traffic between subnets Check connectivity to the RCP server by using the ping command If you are accessing the WMIC through a Telnet session and you do not have a valid username make sure that the current RCP username is the one that you want to use for the RCP download You can enter the show users privileged EXEC command to view the valid username If you do not want to use this username create a new RCP username by using the ip remd remote username username global configuration command to be used during all copy operations The new username is stored in NVRAM If you are accessing the WMIC through a Telnet session and you have a valid username this username is used and you do not need to set the RCP username Include the username in the copy command if you want to specify a username for only that copy operat
86. ems support rsh Because you are copying a file from one place to another you must have read permission on the source file and write permission on the destination file If the destination file does not exist RCP creates it for you The RCP requires a client to send a remote username with each RCP request to a server When you copy a configuration file from the WMIC to a server the Cisco IOS software sends the first valid username in this list e The username specified in the copy command if a username is specified e The username set by the ip remd remote username username global configuration command if the command is configured Cisco 3200 Series Router Hardware Reference 714 i OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Configuration Files W The remote username associated with the current TTY terminal process For example if the user is connected to the router through Telnet and was authenticated through the username command the WMIC software sends the Telnet username as the remote username The WMIC hostname For a successful RCP copy request you must define an account on the network server for the remote username If the server has a directory structure the configuration file is written to or copied from the directory associated with the remote username on the server For example if the configuration file is in the home directory of a user on the server specify that user s name as the r
87. ents option 4 9 GHz Public Safety WMIC Features Table 6 7 lists the key features of the 4 9 GHz public safety WMIC Table 6 7 Key Features of the 4 9 GHz Public Safety WMIC Feature Description Data Rates Supported 5 MHz channelization 1 5 2 25 3 4 5 6 9 12 and 13 5 Mbps 10 MHz channelization 3 4 5 6 9 12 18 24 and 27 Mbps 20 MHz channelization 6 9 12 18 24 36 48 and 54 Mbps Network Standard At present there is no IEEE 4 9 GHz public safety standard however the public safety standard for the 4 9 GHz WMIC is similar to the IEEE 802 1 1a standard Frequency Band 4 940 GHz to 4 990 GHz Available Transmit 50 mW 17 dBm Power Settings 40 mW 16 dBm 30 mW 15 dBm 20 mW 13 dBm 10 mW 10 dBm 5 mW 7 dBm Compliance 4 9 GHz public safety e Operation restricted to operators meeting requirements of CFR47 Part 90 20 of the technical rules for qualification as a Public Safety operator e Requires an FCC license to operate under this part of the Part 90 Regulation OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 6 Wireless Mobile Interface Cards 4 9 GHz Channels Table 6 8 lists the channel options for the 4 94 GHz to 4 99 GHz band for the United States regulatory domain as per the TIA TR 8 specification Table 6 8 Operating Channel Numbers Channel Center 5 MHz Channel Spacing Channel Center 10 MHz Channel Spac
88. ep username location directory filename system running config or copy rep username location directory filename nvram startup config Using RCP copies the configuration file from a network server to the running configuration or to the startup configuration file This example shows how to copy a configuration file named hostl confg from the netadminl directory on the remote server with an IP address of 172 16 101 101 and load and run those commands on the WMIC bridge copy rep netadmin1 172 16 101 101 host1 confg system running config Configure using hostl confg from 172 16 101 101 confirm Connected to 172 16 101 101 Loading 1112 byte file host1 confg OK bridge SSYS 5 CONFIG Configured from hostl config by rep from 172 16 101 101 This example shows how to specify a remote username of netadmin1 Then it copies the configuration file host2 confg from the netadminl directory on the remote server with an IP address of 172 16 101 101 to the startup configuration bridge configure terminal bridge config ip remd remote username netadmini bridge config end bridge copy rep nvram startup config Address of remote host 255 255 255 255 172 16 101 101 Name of configuration file rtr2 confg host2 confg Configure using host2 confg from 172 16 101 101 confirm Connected to 172 16 101 101 Loading 1112 byte file host2 confg OK OK bridge SSYS 5 CONFIG_NV Non vol
89. er Stack 1 WMIC 1 2 MRPC 3 MARC 4 SMIC 5 FESMIC WMIC 2 7 WMIC 3 Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures Rugged Enclosure End Caps Each Cisco 3200 Rugged Enclosure has two end caps an antenna end cap that connects to the back of the enclosure and an I O end cap that connects to the front of the enclosure The port configurations of the I O end caps vary based on the contents of the enclosure For example the number and location of antenna ports installed on the antenna end cap depend on how many WMICs are installed in the enclosure Note To prevent exposure to the elements we recommend using the protective port covers provided on ports that are not in use and using port covers provided on the mating cables Antenna End Cap The antenna end cap has four antenna ports on the flat side and two ports on the top surface The end cap is used with the Cisco 3270 Rugged Enclosure or the Cisco 3230 Rugged Enclosure The antenna ports are connector type RP TNC Each RP TNC is connected internally to a WMIC Typically two antenna ports are used to support each WMIC If fewer than three WMICs are installed the unused antenna connector ports are sealed with a cap to protect them from the environment Figure 1 6 Cisco 3200 Rugged Enclosure Antenna End Cap with a Mounting Bracket O
90. ername on each RCP request to a server When you copy an image from the WMIC to a server by using RCP the Cisco IOS software sends the first valid username in this list The username specified in the archive download sw or archive upload sw privileged EXEC command if a username is specified The username set by the ip remd remote username username global configuration command if the command is entered The remote username associated with the current TTY terminal process For example if the user is connected to the router through Telnet and was authenticated through the username command the WMIC software sends the Telnet username as the remote username The WMIC hostname For the RCP copy request to execute successfully an account must be defined on the network server for the remote username If the server has a directory structure the image file is written to or copied from the directory associated with the remote username on the server For example if the image file resides in the home directory of a user on the server specify that user s name as the remote username Before you begin downloading or uploading an image file by using RCP do these tasks Ensure that the workstation acting as the RCP server supports the remote shell rsh Ensure that the WMIC has a route to the RCP server The WMIC and the server must be in the same subnetwork if you do not have a router to route traffic between subnets Check connectivity to the RC
91. ervers but you cannot create change or delete VLANs on a VTP client e VTP transparent mode Switches do not participate in VTP A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements However in VTP version 2 transparent switches do forward VTP advertisements that they receive out their trunk interfaces VTP Server Example The following example shows how to configure the switch as a VTP server Router vlan database Router vlan vtp server Setting device to VTP SERVER mode Router vlan vtp domain Lab Network Setting VTP domain name to Lab_Network Router vlan vtp password WATER Setting device VLAN database password to WATER Router vlan exit APPLY completed Exiting Router VTP Client Example The following example shows how to configure the switch as a VTP client Router vlan database Router vlan vtp client Setting device to VTP CLIENT mode Router vlan exit In CLIENT state no apply attempted ERICIN esse Router Cisco 3200 Series Router Hardware Reference lt OL 5816 10 Appendix C Switch Port Functionality 802 1P CoS 802 1P CoS W Disabling VTP VTP Transparent Mode Example The following example shows how to configure the switch as VTP transparent Router vlan database Router vlan vtp transparent Setting device to VTP TRANSPARENT mode Router vlan exit
92. es 1 20 throughput 6 14 6 16 TKIP 6 6 torque values 1 21 transmit sensitivity 6 17 Triple Data Encryption Standard 3DES 2 5 trunking 4 1 OL 5816 10 Cisco 3200 Series Router Hardware Reference E IN index U Universal workgroup bridge mode 6 8 USB Flash storage device caveat 1 11 errors 1 11 V VLAN routing 4 2 wW WDS server 6 9 Wedge Lok 1 20 WEP 6 6 wiring card 1 2 WMIC 2 4 GHz 802 11b g 6 1 4 9 GHz public safety 6 1 5 0 GHz public safety 6 1 console ports 1 9 mode installation and operation 1 19 order of installation 1 4 Z Zeroization AUX port 2 5 3 1 GPIO pin 2 5 E Cisco 3200 Series Router Hardware Reference OL 5816 10
93. eshooting tasks such as reconnecting a loose cable To solve more difficult problems please contact your vendor The key features of the MARC include the following e MPC8250 processor running 210 MHz at the CPU core 150 MHz at the CPM core and 60 MHz on the Motorola 60x bus e 32 MB of flash memory e 128 MB of synchronous DRAM e 10 100 Fast Ethernet full duplex connection with autonegotiation e Console connection with hardware software flow control e Asynchronous EIA TIA 232 serial connection with a 5 V auxiliary power supply for Global Positioning System GPS and auxiliary AUX devices e The AUX port speed can be configured as 2400 4800 9600 19200 38400 57600 or 115200 bps Use the line aux inenumber speed command to modify the speed of the port e A 32 bit PCI bus version 2 1 running at 25 MHz e Supports Zeroization when this featured is configured on the router Caution Zeroization is a feature that erases all potentially sensitive information from the router Zeroization is configured through the command line interface CLI and activated through an actuator attached to the AUX port such as a push button Zeroization is disabled by default on the Cisco 3200 Series router When Zeroization is not configured on the router the AUX port functions as a modem port or a terminal port When declassification is enabled through the CLI we recommend that you do not use the AUX port for any other function tha
94. et Dimensions 3X 312 THRU 19 3X 312 THRU 2X 10X 10 32 WIDE SLOT 4X 406 WIDE SLOT Sx slo Kalo 4X 80 te ete 2X 1 84 Z 32 WIDE SLOT l 1 f ax 50 I z7 T TA 1 o SII 0 F E41 gt ae kl co T c fa ba O eas 00 2x 3 500 T ae 2x 3 30 Q WIJ co l T OJ i 4 l L omen 1 76 l 2X 1 76 2x 1 743 H 6 85 mee X 3 J e 232599 roar OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter1 Cisco 3200 Rugged Enclosures Cisco 3200 Series Router Hardware Reference P24 OL 5816 10 CHAPTER Cisco 3270 Rugged Router Card This chapter describes the features of the Cisco 3270 Rugged Router card The Cisco 3270 Rugged Router card is the core component of a Cisco 3270 Mobile Access Router It is compatible with other Cisco 3200 Series router mobile interface cards MICs such as the Wireless Mobile Interface Card WMIC The Cisco 3270 Rugged Router card is also available as a standalone router card to be embedded into a third party enclosure The Cisco 3270 Rugged Router card includes the host processor memory ports and LED signals Additional components provide power and link interfaces for example the Serial Mobile Interface Card SMIC provides the serial interfaces The exact configuration of your router will va
95. fied the leave old sw keyword you can remove it by entering the delete force recursive filesystem file url privileged EXEC command For filesystem use flash for the system board flash device For file url enter the directory name of the old software image All the files in the directory and the directory are removed Uploading an Image File by Using FTP Step 1 Step 2 Step 3 Step 4 Step 5 A You can upload an image from the WMIC to an FTP server You can later download this image to the same WMIC or to another WMIC of the same tvpe Caution For the download and upload algorithms to operate properly do not rename image directories The upload feature is available only if the HTML pages associated with the Cluster Management Suite CMS have been installed with the existing image Beginning in privileged EXEC mode follow these steps to upload an image to an FTP server Command Purpose Verify that the FTP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using FTP section on page 7 12 Log in to the WMIC through a Telnet session configure terminal Enters global configuration mode This step is required only if you override the default remote username or password see Steps 4 5 and 6 ip ftp username username Optional Changes the default remote username ip ftp password password Optional Changes the default password Cisco 3200 Se
96. g IP Multicast Layer 3 Switching This section describes how to configure IP multicast Layer 3 switching You must enable IP multicast routing globally before you can enable IP multicast Layer 3 switching on Layer 3 interfaces For complete information and procedures refer to these publications e Cisco IOS IP Configuration Guide Release 12 2 at this URL http www cisco com univercd cc td doc product software ios 122 122cgcr fipr_c e Cisco IOS IP Command Reference Volume 1 of 3 Addressing and Services Release 12 2 at this URL http www cisco com univercd cc td doc product software ios 122 122cgcr fipras_r index htm e Cisco IOS IP Command Reference Volume 2 of 3 Routing Protocols Release 12 2 at this URL http www cisco com univercd cc td doc product software ios 122 122cgcr fiprrp_r index htm e Cisco IOS IP Command Reference Volume 3 of 3 Routing Protocols Release 12 2 at this URL http www cisco com univercd cc td doc product software ios 122 122cgcr fiprmc_r index htm To enable IP multicast routing globally Use this command in global configuration mode Command Purpose Router config ip multicast routing Enables IP multicast routing globally Enabling IP PIM on Layer 3 Interfaces You must enable PIM on the Layer 3 interfaces before IP multicast Layer 3 switching functions on those interfaces To enable IP PIM on a Layer 3 interface use the following commands beginning in global configuration
97. gged Enclosures Cisco 3270 Rugged Enclosure The Cisco 3270 Rugged Enclosure operates in a temperature range from 40 to 165 F 40 to 74 C when all ports are copper If the Cisco 3270 Router includes a fiber optic port it operates at a temperature range from 40 to 147 F 40 to 64 C The Cisco 3270 Rugged Enclosure is designed to meet NEMA4 requirements Figure 1 2 shows an example of a fully assembled Cisco 3270 Rugged Enclosure Note the greater length to accommodate the Cisco 3270 Rugged Router card and future expansion Figure 1 2 Cisco 3270 Rugged Enclosure Cisco 3200 Series Router Hardware Reference OL 5816 10 EN Chapter1 Cisco 3200 Rugged Enclosures Cisco 3270 Router Card Stack The Cisco 3270 Rugged Enclosure supports the following configurations One Cisco 3270 Rugged Router card Up to three Wireless Mobile Interface Cards WMICs One Serial Mobile Interface Card SMIC One Fast Ethernet Switch Mobile Interface Card FESMIC One Cisco Mobile Router Power Card MRPC A base configuration includes one of each of the following Cisco 3270 Rugged Router card SMIC FESMIC and MRPC In the Cisco 3270 Rugged Enclosure the cards should be stacked in the order shown in Figure 1 3 The figure includes three optional WMICs If WMICs are added the first WMIC should be installed on the bottom of the stack and the next two WMICs should be installed at the top of the stack Figure 1 3 Example of a
98. he upload algorithm creates the tar file format Copying Image Files by Using FTP You can download a WMIC image from an FTP server or upload the image from the WMIC to an FTP server You download a WMIC image file from a server to upgrade the WMIC software You can overwrite the current image with the new one or keep the current image after a download You upload an WMIC image file to a server for backup purposes You can use this uploaded image for future downloads to the WMIC or another device of the same type This section includes this information e Preparing to Download or Upload an Image File by Using FTP page 7 22 e Downloading an Image File by Using FTP page 7 23 e Uploading an Image File by Using FTP page 7 26 Preparing to Download or Upload an Image File by Using FTP You can copy images files to or from an FTP server The FTP protocol requires a client to send a remote username and password on each FTP request to a server When you copy an image file from the WMIC to a server by using FTP the Cisco IOS software sends the first valid username in this list Cisco 3200 Series Router Hardware Reference 722 i OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil e The username specified in the archive download sw or archive upload sw privileged EXEC command if a username is specified e The username set by the ip ftp username username global configuration command if the com
99. he Wireless Mobile Interface Card WMIC communicates with the router through an internal Fast Ethernet port and is configured through an independent console port the WMIC only draws power only from the bus OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter5 Serial Mobile Interface Card SMIC Component Systems Figure 5 1 shows the 2 port SMIC header and bus locations Figure 5 1 2 port SMIC Header and Bus Locations WA 1 PCI bus 2 60 pin multifunction header for Serial 0 and Serial 1 signals 3 ISA bus 4 Rotary switch Figure 5 2 shows the 4 port SMIC header and bus locations A Caution If you add non Cisco cards that generate signals on the PCI bus the router might shut down Do not add non Cisco cards that generate signals on the PCI bus Figure 5 2 4 port SMIC Header and Bus Locations RA 1 PCI bus 2 60 pin multifunction header for Serial 2 and Serial 3 signals 3 60 pin multifunction header for Serial O and 4 ISA bus Serial 1 signals 5 Rotary switch Cisco 3200 Series Router Hardware Reference OL 5816 10 L Chapter 5 Serial Mobile Interface Card Signals for the SMIC The Cisco Single sideband SSB Serial standard supports the following e EIA TIA 232 EIA TIA 449 EIA 530 EIA 530A X 21 and V 35 standards in both DTE and DCE modes e Signals SSB and LED are provided through the 60 pin multifun
100. he bus to a card above or below the WMIC Both buses comply with the PC 104 Plus standard The PCI bus signals allow the Cisco cards to communicate Non Cisco cards cannot communicate with the Cisco 3200 Series Router cards over the PCI bus Caution If you add non Cisco cards that generates signals on the PCI bus the router might shut down Do not add non Cisco cards that generate signals on the PCI bus Cisco 3200 Series Router Hardware Reference OL 5816 10 sei Chapter6 Wireless Mobile Interface Cards Figure 6 1 shows the WMIC header and bus locations Figure 6 1 WMIC Header and Bus Locations 1 PCI bus 2 Left antenna connector J2 3 Right antenna connector J1 4 ISA bus 5 10 pin Fast Ethernet header 6 24 pin multifunction header Note The PC 104 Plus standard requires that the PCI bus and the ISA bus use keying features in the standard stacking headers to guarantee proper module installation On the PCI bus pin D30 is removed and its opening is plugged On the ISA bus pin C19 and pin B10 are removed and their openings are plugged Antenna Connector On the radio card two ultra miniature coaxial connectors U FL connector connect the coax cables between the WMIC and the external antenna connectors Two connectors support antenna diversity The cable should be as short as possible to minimize the loss in strength of the RF signal The cable carries the RF signal from the antenna to
101. host 172 16 101 101 confirm Building configuration OK Connected to 172 16 101 101 bridge This example shows how to store a startup configuration file on a server bridge configure terminal bridge config ip remd remote username netadmin2 bridge config end bridge copy nvram startup config rcp Remote host 172 16 101 101 Name of configuration file to write ap2 confg Write file ap2 confg on host 172 16 101 101 confirm OK Clearing Configuration Information This section describes how to clear configuration information Deleting a Stored Configuration File A Caution You cannot restore a file after it has been deleted Cisco 3200 Series Router Hardware Reference OL 5816 10 a 747 Chapter 7 Managing Firmware and Configurations W Working with Software Images To delete a saved configuration from flash memory use the delete flash filename privileged EXEC command Depending on the setting of the file prompt global configuration command you might be prompted for confirmation before you delete a file By default the WMIC prompts for confirmation on destructive file operations For more information about the file prompt command refer to the Cisco IOS Command Reference for Release 12 1 Working with Software Images amp This section describes how to archive download and upload software image files which contain the system software Cisco IOS code radio firmware and the web ma
102. ide power to the components on the cards Both buses comply with the PC 104 Plus standard The ISA bus allows PC 104 Plus ISA signals to pass through the card bus but the Cisco cards do not use anv of the signals The PCI bus signals allow the Cisco cards to communicate Non Cisco cards cannot communicate with the Cisco 3200 Series Mobile Access Router cards over the PCI bus Caution If vou add non Cisco cards that generate signals on the PCI bus the router might shut down Do not add non Cisco cards that generate signals on the PCI bus Figure 4 1 shows the 2 port FESMIC header and bus locations Figure 4 1 2 port FESMIC Header and Bus Locations 1 PCI bus 2 20 pin LED header 3 ISA bus 4 Rotary switch 5 FEO Fast Ethernet header 6 FEI Fast Ethernet header OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter4 Fast Ethernet Switch Mobile Interface Card Figure 4 2 shows the 4 port FESMIC header and bus locations Figure 4 2 4 port FESMIC Header and Bus Locations AR On 1 PCI bus 2 20 pin LED header 3 ISA bus 4 Rotary switch 5 8 E0 E3 Fast Ethernet headers Note The PC 104 Plus standard requires that the PCI bus and the ISA bus use keying features in the standard stacking headers to guarantee proper module installation On the PCI bus pin D30 is removed and the D30 opening is plugged On the ISA bus pin C19 and pin B10 are removed a
103. ig no storm control Specifies the unicast suppression level for an interface as a unicast threshold lt 0 100 gt percentage of total bandwidth Use the no keyword to restore the defaults Step5 Router config end Returns to privileged EXEC mode Cisco 3200 Series Router Hardware Reference cis E OL 5816 10 Appendix C Switch Port Functionality IGMP Snooping W Verifying Storm Control Use the show storm control command to view switch port characteristics including the storm control levels set on the interface To verify storm control statistics on an interface use the following commands beginning in privileged EXEC mode Command Purpose show interface interface id Verifies the broadcast suppression discard counter for all counters broadcast interfaces or a specific interface Verify the number of packets discarded show interface interface id Verifies the multicast suppression discard counter for all counters multi ast interfaces or a specific interface Verify the number of packets discarded show interface interface id Verifies the unicast suppression discard counter for all counters unicast interfaces or a specific interface Verify the number of packets discarded IGMP Snooping Internet Group Management Protocol IGMP snooping allows the switch to listen in on the IGMP conversation between hosts and routers When a switch hears an IGMP report from a host f
104. information see the Working with Software Images section on page 7 18 When you no longer need a file on a flash memory device you can permanently delete it To delete a file or directory from a specified flash device use the delete force recursive filesystem file url privileged EXEC command Caution When files are deleted their contents cannot be recovered Use the recursive keyword for deleting a directory and all subdirectories and the files contained in it Use the force keyword to suppress the prompting that confirms a deletion of each file in the directory You are prompted only once at the beginning of this deletion process Use the force and recursive keywords for deleting old software images that were installed by using the archive download sw command but are no longer needed If you omit the filesystem option the WMIC uses the default device specified by the cd command For file url you specify the path directory and the name of the file to be deleted This example shows how to delete the file myconfig from the default flash memory device bridge delete myconfig Creating Displaying and Extracting tar Files You can create a tar file and write files into it list the files in a tar file and extract the files from a tar file as described in the next sections Creating a tar File To create a tar file and write files into it use the following command in privileged EXEC mode archive tar cr
105. ing FCC 4 9 GHz Operational Channels as per the TIA TR 8 Specification Channel Center 20 MHz Channel Spacing 1 OP nN nn w 4945 0 4947 5 4950 0 4950 0 4952 5 4955 0 4955 0 4957 5 4960 0 4960 0 4962 5 4965 0 4965 0 4967 5 4970 0 4970 0 4972 5 4975 0 4975 0 4977 5 4980 0 4980 0 4982 5 4985 0 Note One MHz channel spacing for Channel Center Frequencies is documented in the TIA TR 8 specification but it is not supported by the 4 9 GHz public safety WMIC Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter6 Wireless Mobile Interface Cards Throughput The throughput is a minimum of e 4 Mbps half duplex at one mile line of sight range for a 5 MHz wide channel e 8 Mbps half duplex at one mile line of sight range for a 10 MHz wide channel e 16 Mbps half duplex at one mile line of sight range for a 20 MHz wide channel Modulation Table 6 9 lists the modulation supported modulations and data rates Table 6 9 Modulations and Data Rates Modulation 5 Mbps 10 Mbps 20 Mbps BPSK 1 5 Mbps and 2 25 Mbps 3 Mbps and 4 5 Mbps 6 Mbps and 9 Mbps OPSK 3 Mbps and 4 5 Mbps 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps 16 OAM 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps 24 Mbps and 27 Mbps 64 OAM 12 Mbps
106. ion When you upload a file to the RCP server it must be properly configured to accept the RCP write request from the user on the WMIC For UNIX systems you must add an entry to the rhosts file for the remote user on the RCP server For example suppose that the WMIC contains these configuration lines hostname apl ip rcmd remote username User0 If the WMIC IP address translates to ap1 company com the rhosts file for User0 on the RCP server should contain this line apl company com apl For more information refer to the documentation for your RCP server Downloading a Configuration File by Using RCP To download a configuration file by using FTP follow these steps beginning in privileged EXEC mode OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Configuration Files Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Command Purpose Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using RCP section on page 7 15 Log in to the WMIC through a Telnet session configure terminal Enters global configuration mode This step is required only if you override the default remote username see Steps 4 and 5 ip remd remote username username Optional Specifies the remote username end Returns to privileged EXEC mode copy r
107. ior 6 4 Cisco 3270 Rugged Router card 2 1 Cisco FESMIC 4 4 Cisco MARC 3 3 Cisco SMIC 5 4 Cisco WMIC 6 3 indicators Ethernet 6 4 over temp 2 8 radio traffic 6 4 status 6 4 line concommand 2 4 3 1 OL 5816 10 Cisco 3200 Series Router Hardware Reference E IN index MAC address Cisco 3270 Rugged Router card 2 8 FESMIC 4 2 WMIC 6 7 MDIX 4 2 Mean Time Between Failure MTBF 6 7 media dependent interface MDI 4 2 medium dependent interface crossover 4 1 memory Flash 2 1 3 1 Message Digest Execution Unit MDEU 2 5 message integrity check 6 6 MIB 6 10 modem AUX connection 3 4 DTR DSR RTS and CTS signals 1 17 3 4 GPS modem 3 4 modulation 6 11 6 14 6 16 mounting brackets 1 21 enclosure 1 1 multifunction header 3 3 Multiple basic SSIDs 6 8 NEMA4 design 1 1 protective end cap cover 1 13 rugged enclosure Cisco 3230 1 5 Cisco 3270 1 3 non Cisco cards bus communication 2 2 4 3 5 1 6 1 O operational mode 1 19 WMIC LEDs 1 19 over temp LED 2 8 P PC 104 Plus 2 2 3 2 PCI bus 2 2 3 1 4 3 6 1 PEAP 6 6 performance problems solving B 3 per VLAN spanning tree PVST 4 2 ports 6 2 AUX 1 17 3 4 console 1 17 3 4 Fast Ethernet 2 1 3 1 4 1 serial 2 1 3 1 port speed 2 6 power 2 4 power consumption Cisco 3270 Rugged Router card 2 4 Cisco FESMIC 4 1 Cisco MARC 3 3 Cisco SMIC 5 5 Cisco WMIC 6 7 power local command 6 7 power requirements 6 17 power supply card 1 1 PPP modes
108. ith the Flash File System a 16128000 11118592 flash rw flash 16128000 11118592 unknown rw zflash 32768 26363 nvram rw nvram network rw tftp opaque rw null opaque rw system opaque ro xmodem opaque ro ymodem network rw rcp network rw ftp Table 7 1 lists field descriptions for the show file systems command Table 7 1 show file systems Field Descriptions Field Value Size b Amount of memory in the file system in bytes Free b Amount of free memory in the file system in bytes Type Type of file system flash The file system is for a flash memory device network The file system is for a network device nvram The file system is for a nonvolatile RAM NVRAM device opaque The file system is a locally generated pseudo file system for example the system or a download interface such as brimux unknown The file system is an unknown type Flags Permission for file system ro read only rw read write wo write only Prefixes Alias for file system flash flash file system ftp File Transfer Protocol FTP network server Used to transfer files to or from the network device nvram Non volatile RAM memory NVRAM null Null destination for copies You can copy a remote file to null to determine its size rcp Remote Copy Protocol RCP network server system Contains the system memory including the running configuration tftp Trivial File Transfer
109. itteest Translated Safety Warnings k nnetyt turvallisuutta koskevat varoitukset Attention Ce symbole d avertissement indique un danger Vous vous trouvez dans une situation pouvant entra ner des blessures Avant d acc der cet quipement soyez conscient des dangers pos s par les circuits lectriques et familiarisez vous avec les proc dures courantes de pr vention des accidents Pour obtenir les traductions des mises en garde figurant dans cette publication veuillez consulter l annexe intitul e Translated Safety Warnings Traduction des avis de s curit Warnung Dieses Warnsymbol bedeutet Gefahr Sie befinden sich in einer Situation die zu einer K rperverletzung f hren k nnte Bevor Sie mit der Arbeit an irgendeinem Ger t beginnen seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unf llen bewu t bersetzungen der in dieser Ver ffentlichung enthaltenen Warnhinweise finden Sie im Anhang mit dem Titel Translated Safety Warnings bersetzung der Warnhinweise Cisco 3200 Series Router Hardware Reference o N OL 5816 10 Avvertenza Questo simbolo di avvertenza indica un pericolo Si in una situazione che puo causare infortuni Prima di lavorare su qualsiasi apparecchiatura occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti La traduzione de
110. ivated by actuating a custom switch connected to the GPIO pins or an actuator such as a push button that must be attached to the AUX port There is no way for the router to reliably determine whether a device attached to the AUX port is an actuator Therefore any device attached to the AUX port could potentially trigger declassification When declassification is enabled through the CLI we recommend that you do not use the AUX port for any function other than declassification Cisco 3200 Series Router Hardware Reference OL 5816 10 EG Chapter2 Cisco 3270 Rugged Router Card Ethernet Port Speed and Duplex Mode The router cannot automatically negotiate port speed and duplex mode unless the connecting port is configured speed auto duplex auto or no speed If the port speed is set to a value other than auto such as 10 100 or 1000 Mbps configure the remote link partner port to match the local settings do not configure the link partner port to auto If a copper Gigabit Ethernet port speed is configured as 1000 Mbps it must be configured as duplex auto mode otherwise the link will not come up We recommend that you use the speed auto command and duplex auto command to configure a Gigabit Ethernet port The fiber optic Gigabit Ethernet port does not allow users to configure the mode as speed or duplex The port speed and mode are determined by the SFP module Note Changing the Ethernet por
111. just the new configs directory into the root directory on the local flash file system The remaining files in the saved tar file are ignored bridge archive tar xtract tftp 172 20 10 30 saved tar flash new configs Displaying the Contents of a File To display the contents of any readable file including a file on a remote file system use the more ascii binary ebedic file url privileged EXEC command This example shows how to display the contents of a configuration file on a TFTP server bridge more tftp serverA hampton savedconfig 1 I Saved configuration on server 1 version 11 3 service timestamps log datetime localtime service linenumber service udp small servers service pt vtv logging 1 lt output truncated gt Working with Configuration Files This section describes how to create load and maintain configuration files Configuration files contain commands entered to customize the function of the Cisco IOS software To better benefit from these instructions your WMIC contains a minimal default running configuration for interacting with the system software You can copy download configuration files from a TFTP FTP or RCP server to the running configuration of the WMIC for various reasons e To restore a backed up configuration file e To use the configuration file for another bridge For example you might add another bridge to your network and want it to have a configuration similar to the origin
112. ks The BPDUs on the native VLAN of the trunk are sent untagged to the reserved IEEE 802 1d spanning tree multicast MAC address 01 80 C2 00 00 00 The BPDUs on all other VLANs on the trunk are sent tagged to the reserved Shared Spanning Tree Protocol SSTP One spanning tree is created for every new VLAN that is created on the FESMIC STP is enabled by default on VLAN 1 and on all the newly created VLANs PVST and PVST are enabled by default on the FESMIC For detailed information on how STP works go to http www cisco com Cisco 3200 Series Router Hardware Reference lt OL 5816 10 Appendix C Switch Port Functionality Switch Virtual Interface W Switch Virtual Interface A Switch Virtual Interface SVI represents a VLAN of switch ports as one interface to the routing or bridging function in the system Only one SVI can be associated with a VLAN but it is necessary to configure an SVI for a VLAN only when you wish to route between VLANs fallback bridge nonroutable protocols between VLANs or to provide IP host connectivity to the switch By default an SVI is created for the default VLAN VLAN 1 to permit remote switch administration Additional SVIs must be explicitly configured In Layer 2 mode SVIs provide IP host connectivity only to the system in Layer 3 mode you can configure routing across SVIs SVIs are created the first time that you enter the vlan interface configuration command on a VLAN interface The VL
113. l privileged EXEC command For filesystem use flash for the system board flash device For file url enter the directory name of the old software image All the files in the directory and the directory are removed Cisco 3200 Series Router Hardware Reference 7 30 OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil Uploading an Image File bv Using RCP You can upload an image from the WMIC to an RCP server You can later download this image to the same WMIC or to another WMIC of the same type A Caution For the download and upload algorithms to operate properly do not rename image directories The upload feature is available only if the HTML pages associated with the Cluster Management Suite CMS have been installed with the existing image Beginning in privileged EXEC mode follow these steps to upload an image to an RCP server Command Purpose Step 1 Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload an Image File by Using RCP section on page 7 27 Step 2 Log in to the WMIC through a Telnet session Step3 configure terminal Enters global configuration mode This step is required only if you override the default remote username see Steps 4 and 5 Step4 ip remd remote username username Optional Specifies the remote username Step5 end Returns to privileged EXEC mode Step6 archive upload
114. le When connecting to compatible workstations servers and routers use a crossover cable If Auto MDIX is enabled you can use either a straight through cable or a crossover cable to make the connection as the router automatically changes the signals on the pins to compensate OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter6 Wireless Mobile Interface Cards LED Behavior During normal operations the indicator signals LEDs on the wireless device have the following meanings e The status indicator signals operational status Steady green indicates that the wireless device is associated with at least one wireless client Blinking green indicates that the wireless device is operating normally but is not associated with any wireless devices e The radio indicator blinks green to indicate radio traffic activity The light is normally off but it blinks whenever a packet is received or transmitted over the radio e The Ethernet indicator signals traffic on the wired LAN This indicator is normally green when an Ethernet cable is connected The indicator blinks green when a packet is received or transmitted over the Ethernet infrastructure The indicator is off when the Ethernet cable is not connected Table 6 1 lists the details of LED indicator signals Table 6 1 Indicator Signals Message Ethernet Status Radio Type Indicator Indicator Indicator Meaning Boot lo
115. line wander correction performance e MDIX support Fast Ethernet and Gigabit Ethernet copper only e Jumbo Frame 4400 bytes support on Gigabit Ethernet interfaces e 1OBASE T or IOOBASE TX using a single Ethernet connection e 1O0BASE T IOOBASE TX or 1OOOBASE TX using a Gigabit Ethernet copper connection e 100BAFX 100LX 1000BASE SX 1OOOBASE LX LH for Gigabit Ethernet fiber optic connections The speed is not configurable e Standard carrier signal multiple access collision detect CSMA CD or full duplex operation e Integrated programmable LED drivers 1 Transmit underrun an error on interfaces when the data is not ready on the memory bus when the system attempts to transmit the data a bad packet is transmitted Cisco 3200 Series Router Hardware Reference OL 5816 10 ais Chapter1 Cisco 3200 Rugged Enclosures The Cisco 3230 Router Ethernet port signals are in compliance with IEEE 802 3 The interfaces support the following e Autonegotiation and parallel detection MII interface with extended register capability for 10 100BASE TX connections e Full duplex and half duplex modes e 3 3V operation low power consumption 300 mW typical e Low power sleep mode e 1OBASE T or IOOBASE TX using a single Ethernet connection e Robust baseline wander correction performance e Standard carrier signal multiple access collision detect CSMA CD or full duplex operation e Integrated programmable LED drivers Fast E
116. ll vary depending on how it was configured by your vendor Note This section provides basic information about the SMIC hardware for the purpose of performing simple troubleshooting such as reconnecting a loose cable To solve more difficult problems please contact your vendor Each SMIC provides the following e Support for two to four sets of serial signals with protocol support for High Level Data Link Control HDLC asynchronous synchronous and octet oriented PPP modes The signals can be configured to any serial standard EIA TIA 232 EIA TIA 449 EIA TIA 530 EIA TIA 530A EIA TIA X 21 or CCITT V 35 e DCE and DTE mode support on each set of serial signals e Speeds of 2 Mbps for synchronous data transfer and 115 kbps for asynchronous data transfer on each serial interface All serial standards reach 2 Mbps for synchronous except for the EIA TIA 232 standard which supports up to 192K Note The Peripheral Component Interconnect PCI bus and the Industry Standard Architecture ISA bus use keying features in the standard stacking headers to guarantee proper module installation On the PCI bus pin D30 is removed and its opening is plugged On the ISA Bus pin C19 and pin B10 are removed and their openings are plugged The PCI bus connector supports communication between the SMIC the Fast Ethernet Switch Mobile Interface Card FESMIC and the Cisco 3270 Rugged Router card or Mobile Access Router Card MARC T
117. lle avvertenze riportate in questa pubblicazione si trova nell appendice Translated Safetv Warnings Traduzione delle avvertenze di sicurezza Advarsel Dette varselsymbolet betyr fare Du befinner deg i en situasjon som kan fore til personskade For du utf rer arbeid pa utstyr m du v re oppmerksom pa de faremomentene som elektriske kretser inneb rer samt gj re deg kjent med vanlig praksis nar det gjelder a unnga ulykker Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen kan du se i vedlegget Translated Safety Warnings Oversatte sikkerhetsadvarsler Aviso Este s mbolo de aviso indica perigo Encontra se numa situa o que Ihe poder causar danos fisicos Antes de come ar a trabalhar com qualquer equipamento familiarize se com os perigos relacionados com circuitos el ctricos e com quaisquer pr ticas comuns que possam prevenir poss veis acidentes Para ver as tradu es dos avisos que constam desta publica o consulte o ap ndice Translated Safety Warnings Tradu es dos Avisos de Seguran a jAdvertencia Este simbolo de aviso significa peligro Existe riesgo para su integridad fisica Antes de manipular cualquier equipo considerar los riesgos que entra a la corriente el ctrica y familiarizarse con los procedimientos estandar de prevencion de accidentes Para ver traducciones de las advertencias que aparecen en esta publicaci n consultar el ap ndice titulado Transla
118. load a WMIC image file to a server for backup purposes You can use this uploaded image for future downloads to the same WMIC or another device of the same type This section includes this information e Preparing to Download or Upload an Image File by Using RCP page 7 27 e Downloading an Image File by Using RCP page 7 29 e Uploading an Image File by Using RCP page 7 31 Preparing to Download or Upload an Image File by Using RCP RCP provides another method of downloading and uploading image files between remote hosts and the WMIC Unlike TFTP which uses User Datagram Protocol UDP a connectionless protocol RCP uses TCP which is connection oriented To use RCP to copy files the server from or to which you will be copying files must support RCP The RCP copy commands rely on the rsh server or daemon on the remote system To copy files by using RCP you do not need to create a server for file distribution as you do with TFTP You only need to have access to a server that supports the remote shell rsh Most UNIX systems support rsh Because you are copying a file from one place to another you must have read permission on the source file and write permission on the destination file If the destination file does not exist RCP creates it for you OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter 7 Managing Firmware and Configurations W Working with Software Images RCP requires a client to send a remote us
119. lower for small frames and higher for large frames Small packet streams on Gigabit Ethernet ports such as 64 byte packet streams support up to 24 percent of full duplex bidirectional line rate traffic without experiencing packet drops The 512 byte packet streams support up to 78 percent of full duplex bidirectional line rate traffic The 1518 byte packet streams support up to 88 percent of full duplex bidirectional line rate traffic At higher frame rates the RDRP receive drop counter displayed by using the show controller g0 0 command increases indicating dropped packets At higher frame rates for packet sizes greater than 512 bytes the transmit underruns counter displayed by using the show int g0 0 or show int g0 command increases The transmit underruns might cause CRC errors on the peer router Fast Ethernet Signals A Cisco router identifies a Ethernet port interfaces by slot number and port number in the format of slot port For example the slot port address of a Fast Ethernet interface on the Cisco 3230 Rugged Enclosure is 0 0 The Cisco 3270 Router Ethernet port signals are in compliance with IEEE 802 3 The interfaces support the following e Autonegotiation and parallel detection MII interface with extended register capability for 10 100BASE TX or 10 100 1000BASE TX connections e Full duplex and half duplex modes e 3 3V operation low power consumption 300 mW typical e Low power sleep mode e Robust base
120. ltifunction header Note The PC 104 Plus standard requires that the PCI Bus and the ISA bus use keying features in the standard stacking headers to guarantee proper module installation On the PCI bus pin D30 is removed and the D30 opening is plugged On the ISA bus pin C19 and B10 are removed and the C19 and B10 openings are plugged Cisco 3200 Series Router Hardware Reference me OL 5816 10 Chapter3 Mobile Access Router Card MARC Power Requirements The MARC uses 3 3 V 5 V and 12 V power sources Internal on board DC to DC conversion circuitry generates 1 8 V 1 5 A from the 3 3 V power source Table 3 1 MARC Voltages Voltage Current Power 5 0 V 0 3 A 1 5 W 12 0 V 0 1 A 1 2 W 3 3 V 2 0 A 6 6 W MARC Router Signals Cisco 3200 Series router cards do not support any ISA bus signals The PCI bus connector supports communication between Cisco 3200 Series Mobile Access Router cards amp Note Non Cisco MIC cards cannot use PCI signals The use of PCI signals by non Cisco cards causes unpredictable results You cannot add third party devices that might attempt to communicate with the SMIC through the ISA or PCI bus The signals are delivered through the shared 34 pin multifunction header and the 10 pin Ethernet header LED signals and 5 V of power are also provided through the shared 34 pin multifunction header Fast Ethernet Signals on the MARC There is one fixed
121. ly when explicitly configured by a user Figure C 5 Switch Virtual Interface Architecture Layer 3 Routing Unnumbered Unnumbered 82636 e0 1 e0 2 e0 3 e1 1 e1 2 e1 3 e2 1 OL 5816 10 Cisco 3200 Series Router Hardware Reference E Appendix C Switch Port Functionality HE VLANTrunk Protocol VTP VLAN Trunk Protocol VTP VLAN Trunk Protocol VTP is a Layer 2 messaging protocol that maintains VLAN configuration consistency by managing the addition deletion and renaming of VLANs within a VTP domain A VTP domain also called a VLAN management domain is made up of one or more switches that share the same VTP domain name and that are interconnected with trunks VTP minimizes configuration errors and configuration inconsistencies that can result in a number of problems such as duplicate VLAN names incorrect VLAN type specifications and security violations The FESMIC supports both VTP version 1 and version 2 e VTP server mode You can create modify or delete VLANs and specify other configuration parameters such as VTP version and VTP pruning for the entire VTP domain VTP servers advertise their VLAN configuration to other switches in the same VTP domain and synchronize their VLAN configuration with other switches based on advertisements received over trunk links VTP server is the default mode e VTP clients mode Behaves the same way as VTP s
122. m 14 dBm 54 Mbps 13 dBm 13 dBm 13 dBm Cisco 3200 Series Router Hardware Reference OL 5816 10 M cis Chapter6 Wireless Mobile Interface Cards 1 The 5 725 GHz to 5 825 GHz range is not supported on European models Additional cards and components provide power and link interfaces to the WMIC The exact configuration of your router will vary depending on how the vendor configured it 5 GHz WMIC Cisco 3205 The 5 GHz Cisco 3205 WMIC can be configured in any of the following modes e Root bridge e Non root bridge e Workgroup bridge e Access point When configured in a workgroup bridge station role the WMIC can associate to a Cisco 1522 Mesh Access Point serving as a wireless backhaul for an in vehicle mobile network The Cisco 3205 WMIC can also be used to set up point to point or point to multipoint bridges The new 5 GHz radio in this WMIC improves throughput at lower temperatures Supported Channels North America customers can use only the following frequencies in the 5 725 to 5 850 GHz band 5745 MHz 149 5765 MHz 153 5785 MHz 157 5805 MHz 161 5825 MHz 165 To comply with FCC regulations use of the following frequencies is prohibited in North America e 5 250 to 5 350 GHz 5260 MHz 52 5280 MHz 56 5300 MHz 60 5320 MHz 64 e 5 470 to 5 725 GHz 5500 MHz 100 5520 MHz 104 5540 MHz 108 5560 MHz 112 5580 MHz 116 5600 MHz 120 5620 MHz 124 5640 MHz 128 5660 MHz 132 5680 MHz
123. mand is configured e Anonymous The WMIC sends the first valid password in this list e The password specified in the archive download sw or archive upload sw privileged EXEC command if a password is specified e The password set by the ip ftp password password global configuration command if the command is configured e The WMIC forms a password named username apname domain The variable username is the username associated with the current session apname is the configured hostname and domain is the domain of the WMIC The username and password must be associated with an account on the FTP server If you are writing to the server the FTP server must be properly configured to accept the FTP write request from you Use the ip ftp username and ip ftp password commands to specify a username and password for all copies Include the username in the archive download sw or archive upload sw privileged EXEC command if you want to specify a username only for that operation If the server has a directory structure the image file is written to or copied from the directory associated with the username on the server For example if the image file resides in the home directory of a user on the server specify that user s name as the remote username Before you begin downloading or uploading an image file by using FTP perform these tasks e Ensure that the WMIC has a route to the FTP server The WMIC and the FTP server must be in the same subnet
124. mware and Configurations W Working with Configuration Files If the server has a directory structure the configuration file is written to or copied from the directory associated with the username on the server For example if the configuration file resides in the home directory of a user on the server specify that user s name as the remote username For more information refer to the documentation for your FTP server This section includes this information e Preparing to Download or Upload a Configuration File by Using FTP page 7 12 e Downloading a Configuration File by Using FTP page 7 12 e Uploading a Configuration File by Using FTP page 7 13 Preparing to Download or Upload a Configuration File by Using FTP Before you begin downloading or uploading a configuration file by using FTP perform these tasks e Ensure that the WMIC has a route to the FTP server The WMIC and the FTP server must be in the same subnetwork if you do not have a router to route traffic between subnets Check connectivity to the FTP server by using the ping command e Ifyou are accessing the WMIC through a Telnet session and you do not have a valid username make sure that the current FTP username is the one that you want to use for the FTP download You can enter the show users privileged EXEC command to view the valid username If you do not want to use this username create a new FTP username by using the ip ftp username username global configuration comm
125. n declassification This is because there is no way for the router to reliably determine if a device attached to the AUX port is an actuator therefore any device attached to the AUX port could potentially trigger declassification OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter3 Mobile Access Router Card The PCI bus connector supports communication between the Serial Mobile Interface Card SMIC the Fast Ethernet Switch Mobile Interface Card FESMIC and the Mobile Access Router Card The Wireless Mobile Interface Card WMIC communicates with the router through an internal Fast Ethernet port and is configured through an independent console port the WMIC only draws power from the bus MARC Component Systems A The industry standard architecture ISA buses and peripheral component interconnect PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards Both buses comply with the PC 104 Plus standard The ISA bus allows PC 104 Plus ISA signals to pass through the card bus but the Cisco cards do not use any of the signals Caution wy If you add non Cisco cards that generates signal on the PCI bus the router might shut down Please do not add non Cisco cards that generate signals on the PCI bus Figure 3 1 shows the MARC header and bus locations Figure 3 1 MARC Header and Bus Locations 1 IPCI bus 2 ISA bus 3 Ethernet header 4 Mu
126. n helpful suggestions or references to materials not contained in this manual A Caution Means reader be careful In this situation you might do something that could result in equipment damage or loss of data A Warning This warning symbol means danger You are in a situation that could cause bodily injury Before you work on any equipment be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents To see translations of the warnings that appear in this publication refer to the appendix Translated Safety Warnings Waarschuwing Dit waarschuwingssymbool betekent gevaar U verkeert in een situatie die lichamelijk letsel kan veroorzaken Voordat u aan enige apparatuur gaat werken dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico s en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen kunt u het aanhangsel Translated Safety Warnings Vertalingen van veiligheidsvoorschriften raadplegen Varoitus Tama varoitusmerkki merkitsee vaaraa Olet tilanteessa joka voi johtaa ruumiinvammaan Ennen kuin ty skentelet mink n laitteiston parissa ota selv s hk kytkent ihin liittyvist vaaroista ja tavanomaisista onnettomuuksien ehk isykeinoista T ss julkaisussa esiintyvien varoitusten k nn kset l yd t li
127. nagement HTML files You download an WMIC image file from a TFTP FTP or RCP server to upgrade the WMIC software You upload an WMIC image file to a TFTP FTP or RCP server for backup purposes You can use this uploaded image for future downloads to the same WMIC or another of the same type The protocol you use depends on which type of server you are using The FTP and RCP transport mechanisms provide faster performance and more reliable delivery of data than TFTP These improvements are possible because FTP and RCP are built on and use the Transmission Control Protocol Internet Protocol TCP IP stack which is connection oriented This section includes this information e Image Location on the WMIC page 7 18 e tar File Format of Images on a Server or Cisco com page 7 19 e Copying Image Files by Using TFTP page 7 19 e Copying Image Files by Using FTP page 7 22 e Copying Image Files by Using RCP page 7 27 Note For a list of software images and supported upgrade paths refer to the release notes for your WMIC Image Location on the WMIC The Cisco IOS image is stored in a directory that shows the version number A subdirectory contains the HTML files needed for web management The image is stored on the system board flash memory flash You can use the show version privileged EXEC command to see the software version that is currently running on your WMIC In the display check the line that begins with System image file is
128. nd which downloads the image first and does not delete the current running version until the download succeeds The download algorithm verifies that the image is appropriate for the WMIC model and that enough DRAM is present or it aborts the process and reports an error If you specify the overwrite option the download algorithm removes the existing image on the flash device whether or not it is the same as the new one downloads the new image and then reloads the software Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version you must specify the overwrite option If you specify the leave old sw the existing files are not removed If there is not enough space to install the new image and keep the current running image the download process stops and an error message is displayed The algorithm installs the downloaded image on the system board flash device flash The image is placed into a new directory named with the software version string and the system boot path variable is updated to point to the newly installed image If you kept the old image during the download process you specified the leave old sw keyword you can remove it by entering the delete force recursive filesystem file url privileged EXEC command For filesystem use flash for the system board flash device For file url enter the directory name of the old image All the
129. nd Purpose Step4 end Returns to privileged EXEC mode Step5 copy Using FTP copies the configuration file from a network ftp username password location directory server to the running configuration or to the startup filename system running config configuration file or copy ftp username password location directory filename nvram startup config This example shows how to copy a configuration file named hostl confg from the netadmin directory on the remote server with an IP address of 172 16 101 101 and to load and run those commands on the WMIC bridge copy ftp netadmini mvpass06172 16 101 101 hostl confg svstem running config Configure using hostl confg from 172 16 101 101 confirm Connected to 172 16 101 101 Loading 1112 byte file host1l confg OK bridge SSYS 5 CONFIG Configured from hostl config by ftp from 172 16 101 101 This example shows how to specify a remote username of netadmin1 The software copies the configuration file host2 confg from the netadminl directory on the remote server with an IP address of 172 16 101 101 to the WMIC startup configuration bridge configure terminal bridge config ip ftp username netadmini bridge config ip ftp password mypass bridge config end bridge copy ftp nvram startup config Address of remote host 255 255 255 255 172 16 101 101 Name of configuration file rtr2 confg host2 confg Configure using host2 confg from 172 16 101 101 co
130. nd their openings are plugged Signals for the FESMIC The signals are delivered through 10 pin headers with one set of Fast Ethernet signals per header LED signals and 5 V of power are provided through the 20 pin LED header Cisco 3200 Series router cards do not support any ISA bus signals The PCI bus connector supports communication between the FESMIC the Serial Mobile Interface Card SMIC and the Cisco 3270 Rugged Router card or Mobile Access Router Card MARC The Wireless Mobile Interface Card WMIC communicates with the router through an internal Fast Ethernet port and is configured through an independent console port the WMIC draws power only from the bus The Fast Ethernet port signals are in compliance with IEEE 802 3 They are provided through the Ethernet headers which support the following e Autonegotiation for 10 100BASE TX connection e Full duplex and half duplex modes e Low power sleep mode e l1OBASE T and IOOBASE TX using a single Ethernet connection e Robust baseline wander correction performance e Standard carrier signal multiple access collision detect CSMA CD or full duplex operation e Integrated LED drivers Cisco 3200 Series Router Hardware Reference mm OL 5816 10 Chapter4 Fast Ethernet Switch Mobile Interface Card The Fast Ethernet ports on the 4 port FESMIC and the 2 port FESMIC are Fast Ethernet switch ports The switch ports support all Layer 2 features The Fast Ethernet 0 0 por
131. ndix B SFP Module Replacement describes how to install and remove small form factor pluggable SFP modules on the Cisco 3270 Rugged Router card OL 5816 10 Cisco 3200 Series Router Hardware Reference E Audience and Scope The audience for this document is the system administrator SA the SI and the system engineer SE They are experts with networking industry training and experience We assume that users are familiar with the terminology and concepts of the PC 104 Cisco IOS software and Mobile IP networking The SA SI or SE refers to this document to understand how the router hardware is connected to peripheral devices and to perform minor troubleshooting on the cards in an existing router Although they might not be specifically identified as SAs SIs or SEs all users of this documentation are assumed to have comparable skills and knowledge Related Documentation You can access these documents on the Documentation page on Cisco Connection Online CCO at www cisco com The following documentation is available at the http www cisco com en US products hw routers ps272 tsd_products_support_series_home html e Release Notes for the Cisco 3200 Series Mobile Access Routers 78 13975 Provides information about accessing documentation and technical assistance for the Cisco 3200 Series router e Radio Channels and Transmit Frequencies OL 11491 03 Description of how to determine the radio type and how to configure r
132. ndwidth is programmable as the maximum number of packets of each CoS The FESMIC 10 100 Fast Ethernet interfaces default to use the strict priority based scheduling After system boots you can enable weighted round robin scheduling Mapping 802 1P priority to IP precedence bits is not supported OL 5816 10 Cisco 3200 Series Router Hardware Reference E Appendix C Switch Port Functionality E Spanning Tree Protocol STP Spanning Tree Protocol STP amp Spanning Tree Protocol STP is a link management protocol that provides path redundancy while preventing undesirable loops in the network For an Ethernet network to function properly only one active path can exist between any two stations When two ports on a switch are in a loop the spanning tree port priority and port path cost setting determine which port to put in the forwarding state and which port to put in the blocking state The 802 1Q standard defines the method for running multiple VLANs over single or multiple physical LAN segments and defines a unique spanning tree instance to be created on each of the VLAN instances for all the VLANs in a network A mono spanning tree MST network lacks some flexibility compared to a per VLAN spanning tree PVST network which runs one instance of STP per VLAN One spanning tree is created for every new VLAN created on a FESMIC interface STP is enabled by default on VLAN 1 and on all newly created VLANs Cisco develo
133. nfirm Connected to 172 16 101 101 Loading 1112 byte file host2 confg OK OK bridge SSYS 5 CONFIG_NV Non volatile store configured from host2 config by ftp from 172 16 101 101 Uploading a Configuration File bv Using FTP To upload a configuration file bv using FTP follow these steps beginning in privileged EXEC mode Command Purpose Step 1 Verify that the RCP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using RCP section on page 7 15 Step 2 Log in to the WMIC through a Telnet session Step3 configure terminal Enters global configuration mode This step is required only if you override the default remote username or password see Steps 4 5 and 6 Cisco 3200 Series Router Hardware Reference OL 5816 10 a 713 Chapter 7 Managing Firmware and Configurations WE Working with Configuration Files Step 4 Step 5 Step 6 Step 7 Command Purpose ip ftp username username Optional Changes the default remote username ip ftp password password Optional Changes the default password end Returns to privileged EXEC mode copy system running config Using FTP stores the WMIC running or startup ftp username password Jlocationj directorv configuration file to the specified location filename or copy nvram startup config ftp username password location directory filename This example
134. ngine SEC 2 0 is optimized to handle all the algorithms associated with IPSec Secure Sockets Layer SSL Transport Layer Security TLS Secure Real time Transport Protocol SRTP 802 111 Internet SCSI SCSI and Internet key exchange IKE processing The security engine contains four crypto channels a controller and a set of crypto execution units EUs The SEC can act as a master on the internal bus This allows the SEC to alleviate the data movement bottleneck normally associated with slave only cores The host processor accesses the SEC through its device drivers using system memory for data storage The SEC resides in the peripheral memory map of the processor therefore when an application requires cryptographic functions it creates descriptors for the SEC that define the cryptographic function to be performed and the location of the data The SEC bus mastering capability permits the host processor to set up a crypto channel with a few short register writes leaving the SEC to perform reads and writes on system memory to complete the required task Cisco 3200 Series Router Hardware Reference OL 5816 10 Chapter2 Cisco 3270 Rugged Router Card The EUs are e Public Key Execution Unit PKEU supporting RSA and Diffie Hellman Programmable field size up to 2048 bits Elliptical curve cryptography e Data Encryption Standard Execution Unit DEU Data Encryption Standard DES Triple Data Encryp
135. nning config and startup config keyword shortcuts For example the copy running config startup config command saves the currently running configuration file to the NVRAM section of flash memory to be used as the configuration during system initialization Network file system URLs include ftp rep and tftp and have the following syntax e File Transfer Protocol FTP ftp username password location directory filename e Remote Copy Protocol RCP rep username location directory filename e Trivial File Transfer Protocol TFTP tftp location directory filename Local writable file systems include flash Some invalid combinations of source and destination exist Specifically you cannot copy these combinations e From a running configuration to a running configuration e From a startup configuration to a startup configuration e From a device to the same device for example the copy flash flash command is invalid Cisco 3200 Series Router Hardware Reference ra E OL 5816 10 L Chapter 7 Managing Firmware and Configurations Deleting Files A Working with the Flash File System lil For specific examples of using the copy command with configuration files see the Working with Configuration Files section on page 7 7 To copy software images either by downloading a new version or uploading the existing one use the archive download sw or the archive upload sw privileged EXEC command For more
136. o the console port and the AUX port can be accessed simultaneously For example you can connect a terminal to the console interface and an external modem or a GPS modem to the AUX port The console port signals are provided through the multifunction header e Asynchronous serial DCE e 1 2 kbps 2 4 kbps 4 8 kbps 9 6 kbps 19 2 kbps 38 4 kbps 57 6 kbps and 115 2 kbps baud rates e Support full modem control DTR DSR RTS and CTS signals The AUX port is a serial asynchronous port that works at speeds of 1 2 kbps 2 4 kbps 4 8 kbps 9 6 kbps 19 2 kbps 38 4 kbps 57 6 kbps and 115 2 kbps The AUX port supports the following e Asynchronous serial DTE e Baud rates range from 1 200 to 115 000 e 5 to 8 data bits e 1 1 5 or 2 stop bits e Odd even or no parity e Flow control by using RTS CTS DTR and CDC signals Note When zeroization is enabled it is activated through the polling of pin 25 on the AUX port A 5 V power supply is provided for a device connected to an AUX port Typically the 5 V power supply current to GPS modems should be limited to less than 200 mA Cisco 3200 Series Router Hardware Reference EN OL 5816 10 CHAPTER l Fast Ethernet Switch Mobile Interface Card The Fast Ethernet Switch Mobile Interface Card is a mobile interface card MIC in a standard PC 104 Plus form factor FESMICs are components of the Cisco 3200 Series Mobile Access Router The 4 port FESMIC provides four sets of swi
137. o Download or Upload a Configuration File by Using TFTP Before you begin downloading or uploading a configuration file by using TFTP perform these tasks e Ensure that the workstation acting as the TFTP server is properly configured On a Sun workstation make sure that the etc inetd conf file contains this line tftp dgram udp wait root usr etc in tftpd in tftpd p s tftpboot Make sure that the etc services file contains this line Cisco 3200 Series Router Hardware Reference OL 5816 10 A 79 Chapter 7 Managing Firmware and Configurations W Working with Configuration Files tftp 69 udp amp Note You must restart the inetd daemon after modifying the etc inetd conf and etc services files To restart the daemon either stop the inetd process and restart it or enter a fastboot command on the SunOS 4 x or a reboot command on Solaris 2 x or SunOS 5 x For more information on the TFTP daemon refer to the documentation for your workstation e Ensure that the WMIC has a route to the TFTP server The WMIC and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets Check connectivity to the TFTP server by using the ping command e Ensure that the configuration file to be downloaded is in the correct directory on the TFTP server usually Aftpboot on a UNIX workstation e For download operations ensure that the permissions on the file are set correctly The pe
138. o time out Storm control is configured for the switch as a whole although it operates on a per interface basis By default storm control is disabled Storm control prevents switch ports on a LAN from being disrupted by a broadcast multicast or unicast storm on one of the interfaces A LAN storm occurs when packets flood the LAN creating excessive traffic and degrading network performance Errors in the protocol stack implementation or in the network configuration can cause a storm Storm control monitors incoming traffic statistics over a time period and compares the measurement with a predefined suppression level threshold The threshold represents the percentage of the total available bandwidth of the port If the threshold of a traffic type is reached further traffic of that type is suppressed until the incoming traffic falls below the threshold level The graph in Figure C 6 shows broadcast traffic patterns on an interface over a given period of time In this example the broadcast traffic exceeded the configured threshold between time intervals TI and T2 and between intervals T4 and T5 When the amount of specified traffic exceeds the threshold all traffic of that kind is dropped Therefore broadcast traffic is blocked during those intervals At the next time interval if broadcast traffic does not exceed the threshold it is again forwarded Figure C 6 Broadcast Suppression Example Forwarded traffic Blocked traffic Total
139. odule Use the errdisable recovery cause gbic invalid global configuration command to verify the port status and enter a time interval to recover from the error disable state Device does not The SFP module might be installed Verify that the SFP module is not recognize the SFP upside down installed upside down module The SFP module did not snap into Remove the SFP module Inspect for the slot physical damage to the connector the module and the module slot Replace the SFP module with a known good SFP module Excessive errors found Bad adapter in attached device or Run adapter card diagnostic utility and in port statistics STP checking for possible loops wait 30 seconds for the port LED to turn green Error Messages Error Message Transceiver module inserted in port Explanation The online insertion and removal OIR facility detected a newly inserted transceiver module for the interface specified in the error message ErrorMessage INIT_FAILURE Explanation An initialization failure occurred for the transceiver module for the interface specified in the error message This condition could be caused by software firmware or hardware problem As aresult of the error the module is disabled Detected for transceiver module in port module disabled Recommended Action Try reseating the module Hardware replacement should not occur first occurrence Before requesting hardware replacement review troubleshooting logs with
140. odules are inserted into the SFP module slot on the Cisco 3270 Rugged Router card These modules provide the uplink optical interfaces laser send TX and laser receive RX The following are qualified Gigabit SFP modules e Gigabit Multi Mode SFP Cisco part number GLC SX MM RGD e Gigabit Single Mode SFP Cisco part number GLC LX SM RGD Each SFP must be of the same type as the SFP on the other end of the cable and the cable must not exceed the stipulated cable length for reliable communications Figure B 1 shows an SFP module that has a bale clasp latch A Caution We strongly recommend that you not install or remove the SFP module while the fiber optic cable is attached to it because of the potential damage to the cables to the cable connector or to the optical interfaces in the SFP module Disconnect the cable before you remove or install an SFP module Removing and installing an SFP module can shorten its useful life Do not remove and insert SFP modules more often than is necessary Figure B 1 SFP Module with a Bale Clasp Latch A Caution To avoid damaging the cables follow standard fiber optic cleaning procedures when connecting fiber optic cables to fiber optic ports Cisco 3200 Series Router Hardware Reference OL 5816 10 MB Appendix B SFP Module Replacement Replacing SFP Modules into SFP Module Slots A This section describes how to replace an SFP module Warning Step 1 Step
141. onent ambient temperature OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter2 Cisco 3270 Rugged Router Card Note The Cisco 3270 router can be ordered with one Gigabit Ethernet copper interface and one fiber optic interface or with two Gigabit Ethernet copper interfaces The port configurations are not interchangeable The PCI bus connector supports communication between the Serial Mobile Interface Card SMIC the Fast Ethernet Switch Mobile Interface Card FESMIC and the Cisco 3270 Rugged Router card The Wireless Mobile Interface Card WMIC communicates with the router through an internal Fast Ethernet port The WMIC is configured through an independent console port the card draws power only from the bus Note For detailed information about the Cisco 3270 Rugged Router card such as header pin assignments see the Cisco 3200 Series Mobile Access Router Technical Reference OL 1927 This book is a controlled document Qualified system integrators can contact Cisco Marketing to receive a copy Cisco 3270 Rugged Router Card Component Systems A The industrv standard architecture ISA buses and peripheral component interconnect PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards Both buses complv with the PC 104 Plus standard The ISA bus allows PC 104 Plus ISA signals to pass through the card bus but the Cisco cards do not use
142. or Website are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 0807R Any Internet Protocol IP addresses used in this document are not intended to be actual addresses Any examples command display output and figures included in the document are shown for illustrative purposes only Any use of actual IP addresses in illustrative content is unintentional and coincidental Cisco 3200 Series Router Hardware Reference 2008 Cisco Systems Inc All rights reserved Introduction to the Cisco 3200 Series Routers vii Audience and Scope viii Related Documentation viii Conventions ix CHAPTER 1 Cisco 3200 Rugged Enclosures 1 1 Cisco 3270 Rugged Enclosure 1 3 Cisco 3270 Router Card Stack 1 4 Cisco 3230 Rugged Enclosure 1 5 Cisco 3230 Router Card Stack 1 6 Rugged Enclosure End Caps 1 7 Antenna End Cap 1 7 I O End Caps for the Cisco 3200 Rugged Enclosures 1 8 End Cap Fast Ethernet and WMIC Console Ports 1 8 Cisco 3270 Router I O End Cap 1 9 Cisco 3230 Router I O End Cap 1 12 Protective End Cap Cover 1 13 I O End Cap Port Signals 1 15 Gigabit Ethernet Signal Limitations 1 15 Fast Ethernet Signals 1 15 Fast Ethernet Port Cabling for the Cisco 3250 and Cisco 3230 Routers Console Port Signals 1 17 AUX Port Signals 1 17 Cisco 3200 Rugged Enclosure LED Indications 1 18 Cisco 3270 Rugged Enclosure I O End Cap LED Indications 1 18 Cisco 3230 Rugged
143. or a given multicast group the switch adds the host s port number to the Group Destination Address GDA list for that group And when the switch hears an IGMP leave it removes the host s port from the content addressable memory CAM table entry The purpose of IGMP snooping is to restrain multicast traffic in a switched network By default a LAN switch floods multicast traffic within the broadcast domain and this can consume a lot of bandwidth if many multicast servers are sending streams to the segment Multicast traffic is flooded because a switch usually learns MAC addresses by looking into the source address field of all the frames it receives But since a multicast MAC address is never used as source address for a packet and since the addresses do not appear in the MAC address table the switch has no method for learning the addresses IGMP Snooping Configuration IGMP snooping is enabled by default ona VLAN Multicast routing has to be enabled on the router first and then PIM Multicast routing protocol has to be enabled on the VLAN interface so that the switch acknowledges the IGMP join and leave messages which are sent from the hosts connected to the switch For example Router config ip multicast routing Router config if interface VLAN1 ip address 192 168 10 1 255 255 255 0 ip pim sparse mode To verify multicasting support use the show ip igmp group command Router show ip igmp group OL 5816 10 Cisco
144. orrupted software Table B 1 describes how to detect and resolve these problems Table B 1 Common SFP Problems Symptom Possible Cause Resolution Poor performance or Cabling distance exceeded Reduce the cable length to within the excessive errors recommended distances Port statistics show excessive frame check sequence FCS See your SFP module documentation late collision or alignment errors for cabling guidelines No connectivity Incorrect or bad cable Verify the pinouts are correct for the The cable is wired incorrectly proper application of cables Replace the cable with a tested good cable Wait 30 seconds for the port LED to turn green STP checking for possible loops OL 5816 10 Cisco 3200 Series Router Hardware Reference mi Appendix B SFP Module Replacement a Table B 1 Common SFP Problems continued Symptom Possible Cause Resolution The port is placed in Bad or non Cisco approved SFP Remove the SFP module and replace it error disabled state module with a Cisco approved module Use the after SFP module is errdisable recovery cause inserted gbic invalid global configuration command to verify the port status and enter a time interval to recover from the error disable state The port is placed in Bad or non Cisco approved SFP Remove the SFP module from the error disabled state module switch and replace it with a after SFP is inserted Cisco approved m
145. oup 1 source learning bridge group 1 spanning disabled no shutdown 1 interface BVIL ip address 20 20 20 2 255 255 255 0 no ip route cache no shutdown ip default gateway 20 20 20 1 1 bridge 1 route ip 1 end Configuration Example for the WMIC Attached to Switch Port 4 hostname MAR1 SWITCHPORT4 1 bridge irb 1 interface Dot11Radio0 no ip address no ip route cache no shutdown 1 cca 0 speed basic 1 0 basic 2 0 basic 5 5 6 0 9 0 basic 11 0 12 0 18 0 24 0 36 0 48 0 54 0 rts threshold 4000 station role root ap only infrastructure client bridge group 1 bridge group 1 subscriber loop control bridge group 1 block unknown source no bridge group 1 source learning no bridge group 1 unicast flooding bridge group 1 spanning disabled 1 interface FastEthernet0 no ip address bridge group 1 no bridge group 1 source learning bridge group 1 spanning disabled no shutdown 1 interface BVIL ip address 10 10 10 2 255 255 255 0 no ip route cache 1 ip default gatewav 10 10 10 1 bridge 1 route ip 1 end Cisco 3200 Series Router Hardware Reference 734 l OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil Configuration Example for the WMIC Attached to Switch Port 3 hostname MAR1 SWITCHPORT3 1 bridge irb 1 interface Dot11Radio0 no ip address no ip route cache no shutdown 1 cca 0 speed basic 1 0 basic 2 0 basic 5 5 6 0 9 0 basic 11 0 12 0 18 0 24 0
146. ped PVST to allow running several STP instances even over an 802 1Q network by using a tunneling mechanism Although beyond the scope of this document PVST can be briefly described as utilizing a Cisco device to connect a MST zone typically another vendor s 802 1Q based network to a PVST zone typically a Cisco 802 1Q based network There is no specific configuration to enter in order to achieve this PVST is a spanning tree that allows the coexistence of both PVST and Shared Spanning Tree Protocol SSTP in a mixed vendor environment The STP described in IEEE 802 1D standard takes a substantial amount of time to converge to a loop free topology It fails to take advantage of the point to point wiring found in modern networks PVST is enabled on all switch platforms Rapid Spanning Tree Protocol RSTP specified in IEEE 802 1w 0 improves the operation of STP while maintaining compatibility with equipment based on the original 802 1d Spanning Tree standard Note The Cisco Shared Spanning Tree Architecture documents use the terms MST and SST to mean Mono Spanning Tree and Shared Spanning Tree respectively The IEEE 802 1s 10 uses the same terms but with exactly opposite meanings i e MST is Multiple Spanning Trees and SST is Single Spanning Tree When you connect two Cisco switches through 802 1Q trunks the switches exchange spanning tree bridge packet data units BPDUs on each VLAN allowed on the trun
147. ppropriate routing through secure Layer 3 routing services Performance Users that require high performance networking can be assigned to their own VLAN You might for example assign an engineer who is testing a multicast application and the servers that the engineer is using to a single VLAN The engineer experiences improved network performance by being on a dedicated LAN The rest of the engineering group experiences improved network performance because the traffic generated by the network intensive application is isolated to another VLAN This of course implies some areas of physical isolation of separate VLANS or prioritized service by tagging support and prioritized queuing classes within the switches and bridges of the 802 1Q VLAN Network management Software on the switch allows you to assign users to VLANs Changing the cabling to change connectivity is no longer necessary in the switched LAN environment because network management tools allow you to reconfigure the LAN logically in seconds OL 5816 10 Cisco 3200 Series Router Hardware Reference E AppendixC Switch Port Functionality W Port Based VLAN Figure C 1 Traditional LAN Segmentation versus VLAN Segmentation Traditional LAN Segmentation Virtual LAN Segmentation VLAN1 VLAN2 VLAN3 Shared hub LAN 1 ooooooo000 Floor 3 LAN2 JA aye eee eee eesti ree Floor 2 _ LAN3 el i i Floor 1 L2 Switch i 7 ee
148. r occurred Please check the rotary switch positions on the MIC cards for the possible misconfiguration of the switch position Table 4 3 shows the FESMIC Fast Ethernet signal assignments The position of the rotary switch determines the port assignments Although the rotary switch has eight positions only one of three positions can be selected The rotary switch position should be unique for each MIC Table 4 3 FESMIC Rotary Switch Positions and Signal Assignments Rotary Switch Position MIC Slot Fast Ethernet Signal Assignments 0 1 FE 1 0 FE 1 1 FE 1 2 FE 1 3 1 2 FE 2 0 FE 2 1 FE 2 2 FE 2 3 2 3 FE 3 0 FE 3 1 FE 3 2 FE 3 3 1 For 4 port FESMIC only Cisco 3200 Series Router Hardware Reference OL 5816 10 Mas Chapter4 Fast Ethernet Switch Mobile Interface Card Cisco 3200 Series Router Hardware Reference rae E OL 5816 10 amp CHAPTER 5 Serial Mobile Interface Card The Serial Mobile Interface Card is one component of the Cisco 3200 Series Mobile Access Router It provides the router up to 4 high speed sets of serial signals in both data terminal equipment DTE and data circuit equipment DCE modes Additional components provide power and link interfaces to the SMIC For example the Cisco 3270 Rugged Router card provides the host processor memory and headers for the Fast Ethernet console and auxiliary signals for the router The exact configuration of your router wi
149. ration options to Reset factory defaults Failures Red Red Red Firmware failure try disconnecting and reconnecting unit power Blinking red Hardware failure The wireless device must be replaced Firmware Red Loading new firmware image Upgrade Kev Features Table 6 2 lists the kev features of the Cisco wireless devices Table 6 2 Key Features Feature Description Wireless Medium Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing OFDM Radio Media Access Carrier sense multiple access with collision avoidance CSMA CA Protocol SNMP Compliance MIB I and MIB II Encryption Key Length 128 bit Quality of Service Prioritization of traffic for different requirements such as voice and video QoS Support OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter6 Wireless Mobile Interface Cards Table 6 2 Key Features continued Feature Description Security Cisco Wireless Security Suite Authentication e 802 1X support including Extensible Authentication Protocol EAP Transport Layer Security TLS Lightweight EAP LEAP Protected EAP PEAP and EAP Subscriber Identity Module SIM to yield mutual authentication and dynamic per user per session WEP keys e MAC address and by standard 802 11 authentication mechanisms Encryption e Static and dynamic IEEE 802 11 WEP keys of 40 bits and 128 bits e 802 11i1 WPAv2 Advanced Encryption Standard Coun
150. rds WMICs This document describes the Cisco cards and the enclosure solutions that are used to assemble Cisco 3200 Series routers A router can be purchased as a complete unit or purchased in part from Cisco and assembled by a qualified system integrator SI as a custom solution For example a qualified SI might assemble cards into a custom enclosure to suit a particular environment Custom solutions based on Cisco cards must include a power source cables and an enclosure For information about the specific hardware configuration of your router contact your SI The following chapters provide information that you need for understanding the physical components of a completed Cisco 3200 Series router This document is not intended to cover assembly or repair instructions Chapter 1 Cisco 3270 Rugged Enclosure describes the enclosures that house the Cisco 3200 Series routers Chapter 2 Cisco 3270 Rugged Router Card describes the Cisco 3270 Rugged Router card layout Chapter 3 Mobile Access Router Card describes the MARC layout Chapter 4 Fast Ethernet Switch Mobile Interface Card describes the FESMIC layout ports and buses Chapter 5 Serial Mobile Interface Card describes the SMIC layout ports and buses Chapter 6 Wireless Mobile Interface Cards describes the WMIC layout ports and buses Appendix A Smart Serial Port External Seal describes how to seal the Smart Serial port Appe
151. rdware Reference E Appendix B SFP Module Replacement Cisco 3200 Series Router Hardware Reference lt OL 5816 10 APPENDIX Switch Port Functionality The 10 100 Fast Ethernet ports on the Cisco 3200 Series router FESMIC default to Layer 2 switch ports The FESMIC is a learning bridge as defined in 802 1D with the Virtual Local Area Network VLAN capabilities of 802 1P Q The BCM5618 is fully capable of line rate switching for all four 10 100 Fast Ethernet ports VLANs provide the segmentation services traditionally provided by routers in LAN configurations as shown in Figure C 1 VLANs make it easy to move an network or to change a network design Broadcast control Just as switches physically isolate collision domains for attached hosts and only forward traffic out a particular port VLANs provide logical collision domains that confine broadcast and multicast traffic to the bridging domain VLANs solve the scalability problems of large flat networks by breaking a single broadcast domain into several smaller broadcast domains Security VLANs improve security by isolating groups High security users can be grouped into a VLAN possibly on the same physical segment If you do not include a router in a VLAN no one outside that VLAN can communicate with the users inside the VLAN and vice versa This extreme level of security can be highly desirable Users outside that VLAN cannot penetrate into the VLAN without an a
152. rence E Chapter1 Cisco 3200 Rugged Enclosures Table 1 5 shows the status of the LEDs when the WMIC is in operational mode Table 1 5 WMIC Operational Mode Indication Status LED Radio LED Green steady At least one bridge is associated Red steadv Loading firmware Firmware failure Green blink No bridges are associated Transmitting or receiving packets on the radio port Amber blink General warning Maximum retries or buffer full Black no light Default Thermal Plates Cisco 3200 Rugged Enclosures use thermal plates and Wedge Loks to transfer heat from the cards to the extrusion Figure l 11 shows a card with thermal plates The conduction cooling removes the need for internal fans Figure 1 11 Router Card with Thermal Plates 270446 1 Power connector 2 WedgeLok 3 JISA bus 4 IPCI bus Cisco 3200 Series Router Hardware Reference P20 i OL 5816 10 Chapter1 Cisco 3200 Rugged Enclosures Mounting Brackets Mounting brackets are available for the enclosures The notches in the mounting brackets allow you to temporarily install the bracket without the router in place The bolts for the notches in the mounting bracket can be installed on the enclosure before the other bolts are installed The partially installed bolts provide enough support to allow you to install the router in the bracket and then install and tighten the remaining bolts The torque values for
153. ries Router Hardware Reference 726 l OL 5816 10 Chapter7 Managing Firmware and Configurations Working with Software Images lil Command Purpose Step6 end Returns to privileged EXEC mode Step7 archive upload sw Uploads the currently running WMIC image to the FTP ftp username password location directory server image name tar e For username password specify the username and password These must be associated with an account on the FTP server For more information see the Preparing to Download or Upload an Image File by Using FTP section on page 7 22 e For location specify the IP address of the FTP server e For directory image name tar specify the directory optional and the name of the software image to be uploaded Directory and image names are case sensitive The image name tar is the name of the software image to be stored on the server The archive upload sw command builds an image file on the server by uploading these files in order info the IOS image the HTML files and info ver After these files are uploaded the upload algorithm creates the tar file format Copying Image Files by Using RCP You can download a WMIC image from an RCP server or upload the image from the WMIC to an RCP server You download a WMIC image file from a server to upgrade the WMIC software You can overwrite the current image with the new one or keep the current image after a download You up
154. rmission on the file should be world read e Before uploading the configuration file you might need to create an empty file on the TFTP server To create an empty file enter the touch filename command where filename is the name of the file you will use when uploading it to the server e During upload operations if you are overwriting an existing file including an empty file if you had to create one on the server ensure that the permissions on the file are set correctly Permissions on the file should be world write Downloading the Configuration File by Using TFTP Step 1 Step 2 Step 3 Step 4 To configure the WMIC by using a configuration file downloaded from a TFTP server follow these steps Copy the configuration file to the appropriate TFTP directory on the workstation Verify that the TFTP server is properly configured by referring to the Preparing to Download or Upload a Configuration File by Using TFTP section on page 7 9 Log in to the WMIC through a Telnet session Download the configuration file from the TFTP server to configure the WMIC Specify the IP address or hostname of the TFTP server and the name of the file to download Use one of these privileged EXEC commands e copy tftp location directory filename svstem running config e copy tftp location directory filename nvram startup config The configuration file downloads and the commands are executed as the file is parsed line by line
155. roducts ios cisco ios software releases html or http www cisco com en US products sw iosswrel ps5012 ps4629 index html For information about using Cisco IOS software to configure SNMP see to the following documents e The Configuring SNMP Support chapter of the Cisco IOS Configuration Fundamentals Configuration Guide Release 12 2 e The SNMP Commands chapter of the Cisco IOS Configuration Fundamentals Command Reference Release 12 2 Cisco 3200 Series Router Hardware Reference OL 5816 10 For information about using Cisco IOS software to configure Simple Network Management Protocol SNMP Management Information Base MIB features see to the appropriate documentation for your network management system For information on configuring Mobile IP using Cisco IOS software see to the following documents e The Configuring Mobile IP chapter of the Cisco IOS IP Configuration Guide Release 12 2 e The Mobile IP Commands chapter of the Cisco IOS IP Command Reference Volume 1 of 3 Addressing and Services Release 12 2 Related documents from the Cisco TAC Web pages include e Antenna Cabling http www cisco com warp public 102 wlan antcable html Obtaining Documentation and Submitting a Service Request For information on obtaining documentation submitting a service request and gathering additional information see the monthly What s New in Cisco Product Documentation which also lists all new and re
156. ry depending on how the device was configured by the vendor The Cisco 3270 Rugged Router card has the following features Support for the PC 104 Plus form factor Dual 32 bit PCI buses one running at 66 MHz and the other at 25 MHz 256 MB 64 bit unbuffered double data rate DDR synchronous DRAM 64 MB 16 bit flash memory Two Fast Ethernet ports with autonegotiation Two Gigabit Ethernet port signal sets with autonegotiation the router can be ordered with support for one fiber optic port and one copper port or with two copper ports Console port signals with modem flow control Asynchronous EJA ITA 232 serial port signals with 5V auxiliary power for GPS AUX devices Two USB 2 0 high speed 480 Mbps port signal sets High performance hardware encryption processor Zeroization to clear up any trace of user data or binary code Industrial grade components that support local component ambient temperature ranges An enhanced PCI to PCI bridge that supports asynchronous operation The asynchronous bridge allows each port to run from a separate independent clock for the highest performance A synchronous clock forces one side of the bridge to slow down to support a slow device on the other side of the bridge asynchronous bridge clock domains can be arbitrarily different 1 Except optical small form factor pluggable SFP modules Optical SFPs have a temperature range of 40 to 85 C device temperature as opposed to local comp
157. ry and be configured independently To avoid conflicts we recommend that you upload the same image to all of the devices CPUs in the enclosure by configuring the router as a TFTP server that can serve the Cisco IOS image to the WMICs The following major steps are required to upload the Cisco IOS image to all the devices in a Cisco 3200 Series router stack Configure the router as shown in the Configuration Example for the MARC section and verify connectivity to a TFTP server To copy the image to the MARC use the copy tftp flash tarfilename command Enter the tftp server flash tarfilename command to configure the MARC as a TFTP server making the image available to the WMICs Configure router for IP connectivity to all of the WMICs Examples are provided in the Fast Ethernet 0 0 WMIC Configuration Example Configuration section on page 7 33 the Configuration Example for the WMIC Attached to Switch Port 4 section on page 7 34 and the Configuration Example for the WMIC Attached to Switch Port 3 section on page 7 35 Upload the new image to the WMICs for example Enter the archive download software overwrite tftp 20 20 20 1 c3202 k9w7 tar command Enter the archive download software overwrite tftp 10 10 10 1 c3202 k9w7 tar command Enter the archive download software overwrite tftp 10 10 10 2 c3202 k9w7 tar command To verify that the new image is in place use the show version command Cis
158. s Router Hardware Reference lt OL 5816 10 Appendix B SFP Module Replacement Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Find the send TX and receive RX markings that identifv the top side of the replacement SFP module amp Note On some SFP modules the send and receive TX and RX markings might be replaced by arrows that show the direction of the connection either send or receive TX or RX Align the SFP module in front of the slot opening Insert the SFP module into the slot until you feel the connector on the module snap into place in the back of the slot Remove the dust plugs from the SFP module optical ports Store the plugs for later use A Caution Do not remove the dust plugs from the SFP module port or the rubber caps from the fiber optic cable until you are ready to connect the cable The plugs and caps protect the SFP module ports and cables from contamination and ambient light Clean the fiber optic connectors by using standard procedures Insert the LC cable connector into the SFP module Verify that the gasket is in place and replace the Antenna end cap by using a 3 8 in wrench to remove the bolts torquing the bolts to 58 to 68 inch pounds Diagnosing SFP Problems You can get statistics from the browser interface from the CLI or from an SNMP workstation Common SFP module problems fall into these categories e Poor performance e No connectivity e C
159. shows how to copy the running configuration file named ap2 confg to the netadminl directory on the remote host with an IP address of 172 16 101 101 bridge copy system running config ftp netadmin1 mypass 172 16 101 101 ap2 confg Write file ap2 confg on host 172 16 101 101 confirm Building configuration OK Connected to 172 16 101 101 bridge This example shows how to store a startup configuration file on a server by using FTP to copy the file bridge configure terminal bridge config ip ftp username netadmin2 bridge config ip ftp password mypass bridge config end bridge copy nvram startup config ftp Remote host 172 16 101 101 Name of configuration file to write ap2 confg Write file ap2 confg on host 172 16 101 101 confirm OK Copying Configuration Files by Using RCP The Remote Copy Protocol RCP provides another method of downloading uploading and copying configuration files between remote hosts and the WMIC Unlike TFTP which uses User Datagram Protocol UDP a connectionless protocol RCP uses TCP which is connection oriented To use RCP to copy files the server from or to which you will be copying files must support RCP The RCP copy commands rely on the rsh server or daemon on the remote system To copy files by using RCP you do not need to create a server for file distribution as you do with TFTP You only need to have access to a server that supports the remote shell rsh Most UNIX syst
160. sole LEDs section on page 1 19 Cisco 3270 Rugged Enclosure I O End Cap LED Indications Table 1 2 lists the LEDs for the Cisco 3270 Rugged Enclosure I O end caps and their indications Table 1 2 LEDs for the Cisco 3270 Rugged Enclosure End Cap LED Indication Cisco 3270 Rugged Router card Solid green OK Blinking Booting and self testing Black Not OK or the power is off Serial Status Link 1 status link LED per serial port Solid green Link OK Black No link is detected Amber blink Activity Fast Ethernet 1 LED per port except for the fiber optic port which has no Link LED Solid green Link OK Black No link is detected LEDs Activity LED Black No activity and no connection Green blink Activity Gigabit Ethernet Link LED 2 LEDs per port Solid green Link OK Black no link is detected Activity LED Solid green Link OK Black No activity Green blink Activity Console Solid green Link OK Black No activity Green blink Activity WMIC Console Installation or Operation Mode For installation mode see Table 1 4 on page 1 19 For operation mode see Table 1 5 on page 1 20 E Cisco 3200 Series Router Hardware Reference OL 5816 10 Cisco 3200 Rugged Enclosures L Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3230 Rugged Enclosure I O End Cap LED Indications Table 1 3 lists the LEDs for the Cisco 3230 Rugged Enclosure I O
161. system board flash device Step2 mkdir old_configs Creates a new directory The command example shows how to create the directory named old_configs Directory names are case sensitive Directory names are limited to 45 characters between the slashes the name cannot contain control characters spaces deletes slashes quotes semicolons or colons Step3 dir filesystem Verifies your entry To delete a directory with all its files and subdirectories use the delete force recursive filesystem file url privileged EXEC command Use the recursive keyword to delete the named directory and all subdirectories and the files contained in it Use the force keyword to suppress the prompting that confirms a deletion of each file in the directory You are prompted only once at the beginning of this deletion process Use the force and recursive keywords for deleting old software images that were installed by using the archive download sw command but are no longer needed For filesystem use flash for the system board flash device For file url enter the name of the directory to be deleted All the files in the directory and the directory are removed A Caution When files and directories are deleted their contents cannot be recovered Copving Files To copy a file from a source to a destination use the copy erase source url destination url privileged EXEC command For the source and destination URLs you can use ru
162. t Ethernet autonegotiation for the line transmission speed Both sides of the connection are automatically set to either IOBASE TX or IOOBASE TX Autonegotiation is widely used on most Ethernet interfaces and it is the default mode When a Fast Ethernet interface is enabled one end of the link must perform media dependent interface MDI crossover MDIX so that the transmitter on one end of the data link is connected to the receiver on the other end of the data link a crossover cable is typically used The Auto MDIX feature eliminates the need for crossover cabling by performing an internal crossover when a straight cable is detected during the autonegotiation phase If autonegotiation is disabled Auto MDI MDIX cannot work because there is no signal transmission at initialization to sample the cabling with Therefore as in all systems not supporting the HP Auto MDIX feature cabling must be correct for the devices being connected The Auto MDIX feature is disabled if you explicitly set the line speed rather than leaving the default mode of autonegotiation Although it is possible to disable HP Auto MDIX with autonegotiation enabled the current software does not implement an explicit command line interface CLI command to allow you to disable Auto MDIX during autonegotiation Autonegotiation Enable To enable autonegotiation use the following configuration Router config FastEthernet m n Router config if speed auto where m is the slot
163. t on the Cisco 3270 Rugged Router card and MARC is a Fast Ethernet router port The routing features supported on the MARC cannot be configured on the FESMIC ports FESMIC Rotary Switch Positions A Cisco router identifies a Fast Ethernet interface address by its slot number and port number in the form of slot port The slot port addresses of the Fast Ethernet interfaces on the FESMIC depend on the position of the rotary switch For example if the rotary switch on the 4 port FESMIC is in position 0 then the ports are identified as 1 0 1 1 1 2 and 1 3 If the rotary switch on the 2 port FESMIC is in position 0 the ports are identified as 1 0 and 1 1 Table 4 2 shows the mapping of the switch positions to the Cisco IOS slot numbers Table 4 2 FESMIC Rotary Switch Positions Switch Position Cisco 10S Slot Number 0 1 1 2 2 3 3 7 Not supported A Caution The rotary switch positions must be unique and should not be assigned to more than one MIC e Ifa MIC rotary switch is set to 3 or higher the message is MIC 3 SLOTNOTSUPPORTED The MIC cannot operate when the rotary switch is in position 3 Change the switch position to one of the supported unused positions 0 2 If two or more MICs have the rotary switches set to the same position or if one or more MICs are in rotary switch positions 4 through 7 the router might crash after displaying the following error message Non recoverable erro
164. t speed and duplex mode configuration might shut down and reenable the interface during the reconfiguration The procedure to set the port speed for a copper Gigabit Ethernet port is as follows Command Purpose Step 1 Router config interface GigabitEthernet s ot port Selects the Ethernet port to be configured Step 2 Router config if speed 10 100 1000 auto Sets the speed of the Ethernet interface Default Router config if no speed Reverts to the default configuration speed auto If you set the port speed to auto on a 10 100 1000 Mbps Ethernet port speed is autonegotiated To set the mode on a copper Gigabit Ethernet port to duplex Command Purpose Step 1 Router config interface GigabitEthernet slot port Selects the Ethernet port to be configured Step 2 Router config if duplex auto full half Sets the duplex mode of the Ethernet port Default Router config if no duplex Reverts to the default configuration duplex auto amp Note The Gigabit Ethernet optical fiber interface only supports full duplex mode a Cisco IOS command to set the mode is not is supported Cisco 3200 Series Router Hardware Reference mo OL 5816 10 Chapter 2 Cisco 3270 Rugged Router Card Cisco 3270 Rugged Router Card Encryption Module The integrated security engine SEC 2 0 is optimized to handle all the algorithms associated with IP security IPSec Secure Sockets Layer SSL Transport Layer Security TLS
165. tar File To display the contents of a tar file on the screen use this privileged EXEC command archive tar table source url For source url specify the source URL alias for the local or network file system These options are supported e For the local flash file system the syntax is flash e For the File Transfer Protocol FTP the syntax is ftp username password location directory tar filename tar e For the Remote Copy Protocol RCP the syntax is rep username location directory tar filename tar e For the Trivial File Transfer Protocol TFTP the syntax is tftp location directory tar filename tar The tar filename tar is the tar file to display You can also limit the display of the files by specifying an optional list of files or directories after the tar file then only these files are displayed If none are specified all files and directories are displayed This example shows how to display the contents of the c1200 k9w7 mx 122 8 JA tar file that is in flash memory bridge archive tar table flash c1200 k9w7 mx 122 8 JA tar info 219 bytes c1400 k9w7 mx 122 11 JA directory c1400 k9w7 mx 122 11 JA html directory c1400 k9w7 mx 122 11 JA html foo html 0 bytes c1400 k9w7 mx 122 11 JA c1200 k9w7 mx 122 8 JA bin 610856 bytes c1400 k9w7 mx 122 11 JA info 219 bytes info ver 219 bytes This example shows how to display only the c1200 k9w7 mx 122 8 JA html directory and its contents
166. tched Fast Ethernet signals The 2 port FESMIC provides two sets of switched Fast Ethernet signals The key features of the FESMIC include the following e Autosensing of switched Fast Ethernet interfaces e Auto MDIX medium dependent interface crossover Auto MDIX automatically detects and corrects crossed Ethernet cabling e Support for 802 1D standard bridging 802 1Q trunking and 802 1P class of service CoS e Layer 3 routing support between VLANs Only one FESMIC is supported in a Cisco 3200 Series router Additional cards and components provide power and link interfaces to the FESMIC The exact configuration of your router will vary depending on how your vendor configured it Note This section provides basic information about the FESMIC hardware for the purpose of performing simple troubleshooting such as reconnecting a loose cable To solve more difficult problems contact your vendor The FESMIC draws power from the PCI and the ISA connectors Table 4 1 shows the estimated power consumption Note that these are theoretical maximum wattages Table 4 1 FESMIC Estimated Power Consumption Voltage Current Draw Power Source 5 0 V 0 2 A 1 0 W ISA and PCI connectors 3 3 V 2 3 A 7 1 W PCI connectors OL 5816 10 Cisco 3200 Series Router Hardware Reference mi Chapter4 Fast Ethernet Switch Mobile Interface Card Autonegotiation and Auto MDI MDIX All of the Fast Ethernet interfaces suppor
167. ted Safety Warnings Varning Denna varningssymbol signalerar fara Du befinner dig i en situation som kan leda till personskada Innan du utf r arbete pa n gon utrustning m ste du vara medveten om farorna med elkretsar och k nna till vanligt f rfarande f r att f rebygga skador Se f rklaringar av de varningar som f rekommer i denna publikation i appendix Translated Safety Warnings versatta s kerhetsvarningar Cisco 3200 Series Router Hardware Reference OL 5816 10 MA Cisco 3200 Series Router Hardware Reference a OL 5816 10 se CHAPTER 1 Cisco 3200 Rugged Enclosures This chapter provides an overview of the Cisco 3200 Rugged Enclosures so that simple troubleshooting such as reconnecting a loose cable can be performed in the field The chapter is not intended as a complete guide to the chassis because the devices should be serviced or repaired by a qualified personnel The enclosure seals the Cisco 3200 Series router cards so that they can withstand the harsh environments that are common in police cars military vehicles trains airborne vehicles and outdoor locations that are exposed to the elements Cisco 3200 Rugged Enclosure features include Symmetrical mounting holes for the mounting brackets so that the unit can be mounted upside down if required A design that meets NEMA4 requirements impervious to rain or hose directed water The enclosure is slightly rounded on the top
168. ted USB flash storage device is plugged into a USB port an error might occur CSCsd44152 The error message is Failed to enumerate a USB device as not able to read the device s description To correct the problems remove any unsupported USB flash storage device and use only one supported device in one of the two USB ports The Cisco supported flash storage devices listed below Item Vendor Part Number 16 3153 01 SANDISK SDUJGU0 256 926 16 3153 01 M SYSTEMS 8U 52E 0256 12A01C 16 3152 01 SANDISK SDUJGU0 128 926 16 3152 01 M SYSTEMS 8U 52E 0128 12A01C 16 3151 01 SANDISK SDUJGU0 64 926 16 3151 01 M SYSTEMS 8U 52E 0064 12A01C OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter1 Cisco 3200 Rugged Enclosures Cisco 3230 Router I 0 End Cap Figure 1 8 shows the Cisco 3230 Router I O end cap It has multiple connectors that can be used to connect power and data cables Figure 1 8 Cisco 3230 Router End Cap 270444 1 WMIC 1 console port 2 WMIC 2 console port 3 WMIC 3 console port 4 FEO port 5 FEIX port 6 FE2X or MARC FEOX port for more information see the Fast Ethernet Port Cabling for the Cisco 3250 and Cisco 3230 Routers section on page l 16
169. ted power consumption Note that these are theoretical maximum wattages Table 5 6 SMIC Estimated Power Consumption Voltage Current Draw Power Source 5 0 V 10A 5 0 W ISA and PCI connectors 13 3 V 0 5A 1 7 W PCI connectors OL 5816 10 Cisco 3200 Series Router Hardware Reference E Chapter5 Serial Mobile Interface Card Cisco 3200 Series Router Hardware Reference OL 5816 10 A CHAPTER Wireless Mobile Interface Cards The Cisco Wireless Mobile Interface Card WMIC is a Cisco 3200 Series router interface card in a standard PC 104 Plus form factor It is one component of the Cisco 3200 Series routers and provides a wireless interface with the following e 2 4 GHz 802 11b g Cisco 3201 e 4 9 GHz public safety Cisco 3202 e 5 0 GHz 802 1 1h Cisco 3205 Caution The 4 9 GHz public safety radio requires an operators license and can be operated only by US Public Safety operators who meet the requirements specified under FCC Part 90 20 This chapter provides basic information about the WMIC hardware for performing simple troubleshooting such as reconnecting a loose cable To solve more difficult problems contact your vendor WMIC Component Systems A The ISA buses and PCI buses on the Cisco 3200 Series router cards provide power to the components on the cards The WMIC does not receive or transmit communications signals on either bus but it will pass signals through t
170. ter Mode with Cipher Block Chaining Message Authentication Code Protocol AES CCMP 128 bit key length e Temporal Key Integrity Protocol TKIP WEP enhancements key hashing per packet keying message integrity check MIC and broadcast key rotation by using WPA TKIP All WMICs in Root Mode PEAP EAP TTLS LEAP EAP TLS EAP FAST and EAP SIM Cisco 3201 WMICs in Client Mode LEAP EAP TLS and EAP FAST Cisco 3202 and Cisco 3205 WMICs in Client Mode LEAP Status Indicators LEDs provide information about association status operation error warning firmware upgrade and configuration network modem and radio status Memory 8 MB Flash 32 MB DRAM Automatic Configuration BOOTP and DHCP Support Remote Configuration Telnet HTTP FTP TFTP and SNMP Support Uplink Autosensing 10 100BaseT Ethernet Local Configuration Console port Cisco 3200 Series Router Hardware Reference lt OL 5816 10 Chapter6 Wireless Mobile Interface Cards MAC Address Allocation The WMIC stores one unique MAC address for the BVI interface WMIC Power Requirement In a typical Cisco 3200 Series router configuration the WMIC draws power from the PCI and the ISA connectors Table 6 3 shows the estimated power consumption Note that these are theoretical maximum wattages Table 6 3 WMIC Power Requirement Voltage Current Draw Power Source 5 0 V 0 4 A 2 0 W ISA and PCI connectors 43 3 V I7A 5 6
171. the following channels and frequencies in the ETSI regulatory domain e 5 250 GHz to 5 350 GHz 5260 MHz 52 5280 MHz 56 5300 MHz 60 5320 MHz 64 e 5 470 GHz to 5 725 GHz 5500 MHz 100 5520 MHz 104 5540 MHz 108 5560 MHz 112 5580 MHz 116 5600 MHz 120 5620 MHz 124 5640 MHz 128 5660 MHz 132 5680 MHz 136 5700 MHz 140 Channels 52 through 140 are ETSI outdoor channels North America customers can use only the following frequencies in the 5 725 GHz to 5 850 GHz band e 5745 MHz 149 e 5765 MHz 153 e 5785 MHz 157 e 5805 MHz 161 e 5825 MHz 165 Note By default the C3205 WMIC performs automatic channel selection on the radio interface For more information about configuring a channel on the radio interface of the Cisco 3205 WMIC by using the command line interface CLI see the Configuring the Radio Channel or Frequency for the C3205 WMIC section in the Radio Channels and Transmit Frequencies document To see Dynamic Frequency Selection DFS statistics use the show interface d0 dfs command Throughput The throughput is a minimum of 16 Mbps half duplex at one mile line of sight range for a 20 MHz wide channel The range performance is dependent on output power antenna gain path loss and other factors The following are range performance estimations e 6 Mbps at 10 kilometers 6 miles at 30 dBm equivalent isotropically radiated power EIRP e 1 Mbps at 30 kilometers 18 miles at
172. the low noise amplifier LNA on the receiver and carries the RF signal from the power amplifier PA to the antenna that radiates the RF signal There are many antenna connector families The Cisco RP TNC antenna connector can be used to support standard antennas WMIC Console and Fast Ethernet Ports Cisco 3200 Series router cards do not support any ISA bus signals The PCI bus connector supports communication between the Cisco 3200 Series router card and the PCI Serial Mobile Interface Card SMIC and between the SMIC and the Fast Ethernet Switch Mobile Interface Card FESMIC In a Cisco Rugged Enclosure the WMIC communicates with the router through the WMIC Fast Ethernet interface The WMIC Fast Ethernet ports are connected internally to Fast Ethernet ports that provide a communications link with the router The WMIC interfaces are configured through a WMIC console port Cisco 3200 Series Router Hardware Reference lt OL 5816 10 Chapter6 Wireless Mobile Interface Cards amp In contrast the Serial Mobile Interface Card SMIC and FESMIC communicate with the router through the PC 104 Plus bus The interfaces are configured through the router console port and all of the router and FESMIC Fast Ethernet ports are identified by using the slot port format The WMIC runs an independent Cisco IOS image and when it is configured the link between the WMIC and the router forms an internal LAN In standard configurations a WMIC
173. thernet Port Cabling for the Cisco 3250 and Cisco 3230 Routers Most Cisco 3200 Series router Ethernet ports support autodetection If the device that the router is connected to also supports autodetection the choice of a straight through or crossover Ethernet cable does not matter However the Cisco 3250 router MARC FEOX port does not support autodetection To connect a port marked MARC FEOX to a routing Ethernet port that does not support autodetection use a straight through Ethernet cable To connect a MARC FEOX port to a hub switch a router hub or switch port use a crossover Ethernet cable Table 1 1 shows the connections Table 1 1 General Guidelines for MAR Fast Ethernet Port Cabling Server Workstation or Personal Hub Switch Uplink Router Ports Computer Ethernet Link Ethernet Hub or Switch Ports marked FEOX FE1X Straight through cable Crossover cable and so forth Ports marked FEO FE1 and Crossover cable Straight through cable so forth For example a port marked FEOX requires a crossover Ethernet cable to establish the Ethernet link between a Cisco 3250 router and a hub A port that does not support autodetection marked FEO requires a straight through Ethernet cable to establish the Ethernet link between a Cisco 3250 router and a hub For additional information on cable pin assignments see the Cable Pinouts chapter of the Cisco Content Services Switch Getting Started Guide at http www cisco com en
174. tion Standard 3DES Two key KI K2 or three key KI K2 K3 Ethernet Bundling Controller EBC and Cipher Block Chaining CBC modes for both DES and 3DES e Advanced Encryption Standard Unit AESU Implements the Rinjdael symmetric key cipher Key lengths of 128 192 and 256 bits ECB CBC CCM and AES Counter Mode a block cipher that encrypts 128 bit blocks of data at a time with a 128 bit encryption key e ARC Four execution unit AFEU A stream cipher compatible with the RC4 algorithm 40 to 128 bit programmable key e Message Digest Execution Unit MDEU Secure Hash Algorithm SHA with a 160 bit or 256 bit message digest Message Digest 5 MD5 with a 128 bit message digest Hash based Message Authentication Code HMAC with either algorithm e Random Number Generator RNG e Four crypto channels each supporting multi command descriptor chains Static or dynamic assignment of crypto execution units through an integrated controller Buffer size of 256 bytes for each EU with flow control for large data sizes A Caution Zeroization is a feature that erases all potentially sensitive information from the router It is disabled by default on the router When Zeroization is not configured on the router the AUX port functions as a modem port or a terminal port Zeroization is configured through the command line interface CLI but it cannot be activated through the CLI Zeroization is act
175. ugged Router card 2 3 Cisco FESMIC 4 1 Cisco MARC 3 1 Cisco WMIC_ 6 2 enclosures 1 15 end cap interfaces 1 15 indicator 6 4 MAC addresses 2 8 switch port 4 5 WMIC internal connections WMIC Fast Ethernet connections 1 9 fiber optic port seal 1 10 Tyco connector 1 10 Flash memory 2 1 3 1 flow control 1 17 2 1 3 4 frequencies 6 11 G Gigabit Ethernet copper 2 6 duplex mode 2 6 Hl Cisco 3200 Series Router Hardware Reference OL 5816 10 limitations 1 15 MAC addresses 2 8 port speed 2 6 SFP module 2 6 GPIO pin 2 5 GPS modem 3 4 power 2 4 3 4 HDLC 54 header keying 2 3 3 2 4 4 5 1 6 2 header locations Cisco 3270 Rugged Router card 2 3 Cisco FESMIC 4 4 Cisco MARC 3 2 Cisco SMIC 5 2 Cisco WMIC 6 2 heat shrink tubing A 1 IKE 2 7 industry standard architecture ISA 2 2 3 2 installation mode WMIC LEDs 1 19 installing SFP modules B 2 to B 3 integrated security engine 2 4 interface identification serial Cisco SMIC 5 4 interfaces AUX 1 17 2 4 3 4 console port 1 17 2 3 3 4 Fast Ethernet Cisco 3270 Rugged Router card 2 3 Cisco FESMIC 4 4 4 5 Cisco MARC 3 3 Cisco WMIC 6 3 endcap 1 15 serial Cisco 3270 Rugged Router card 2 1 Cisco MARC 3 1 Cisco SMIC 5 3 5 4 inter VLAN routing 4 2 IP 67 integrity 1 10 IPSec 2 7 ISA bus signals 2 2 3 2 4 3 6 1 iSCSI 2 7 Index W K key hashing 6 6 keying feature 2 3 3 2 4 4 5 1 6 2 L laser B 1 LEAP 6 6 LED behav
176. username For the RCP copy request to execute successfully an account must be defined on the network server for the remote username For more information see the Preparing to Download or Upload an Image File by Using RCP section on page 7 27 e For location specify the IP address of the RCP server e For directorvlimage name tar specify the directory optional and the image to download Directory and image names are case sensitive Cisco 3200 Series Router Hardware Reference OL 5816 10 M 7 29 Chapter 7 Managing Firmware and Configurations W Working with Software Images Command Purpose Step7 archive download sw leave old sw reload Downloads the image file from the RCP server to the rep username location directory image na_ WMIC and keep the current image me tarl e The leave old sw option keeps the old software version after a download e The reload option reloads the system after downloading the image unless the configuration has been changed and not saved e For username specify the username For the RCP copy request to execute an account must be defined on the network server for the remote username For more information see the Preparing to Download or Upload an Image File by Using RCP section on page 7 27 e For location specify the IP address of the RCP server e For directory image name tar specify the directory optional and the image to download
177. vised Cisco technical documentation at http www cisco com en US docs general whatsnew whatsnew html Subscribe to the What s New in Cisco Product Documentation as a Really Simple Syndication RSS feed and set content to be delivered directly to your desktop using a reader application The RSS feeds are a free service and Cisco currently supports RSS version 2 0 Conventions This publication uses these conventions to convey instructions and information Command descriptions use these conventions e Commands and keywords are in boldface text e Arguments for which you supply values are in italic e Square brackets mean optional elements e Braces group required choices and vertical bars separate the alternative elements e Braces and vertical bars within square brackets mean a required choice within an optional element Interactive examples use these conventions e Terminal sessions and system displays are in screen font e Information you enter isin boldface screen font e Nonprinting characters such as passwords or tabs are in angle brackets lt gt Notes cautions and timesavers use these conventions and symbols Tip Means the following will help you solve a problem The tips information might not be troubleshooting or even an action but could be useful information OL 5816 10 Cisco 3200 Series Router Hardware Reference amp Note Means reader take note Notes contai
178. vity to the TFTP server by using the ping command e Ensure that the image to be downloaded is in the correct directory on the TFTP server usually tftpboot on a UNIX workstation e For download operations ensure that the permissions on the file are set correctly The permission on the file should be world read e Before uploading the image file you might need to create an empty file on the TFTP server To create an empty file enter the touch filename command where filename is the name of the file you will use when uploading the image to the server e During upload operations if you are overwriting an existing file including an empty file if you had to create one on the server ensure that the permissions on the file are set correctly Permissions on the file should be world write Downloading an Image File by Using TFTP You can download a new image file and replace the current image or keep the current image A Caution For the download and upload algorithms to operate properly do not rename image directories To download a new image from a TFTP server and overwrite the existing image follow these steps beginning in privileged EXEC mode Command Purpose Step1 Copy the image to the appropriate TFTP directory on the workstation Make sure the TFTP server is properly configured see the Preparing to Download or Upload an Image File by Using TFTP section on page 7 19 Step 2 Log in to the WMIC through
179. work if you do not have a router to route traffic between subnets Verify connectivity to the FTP server by using the ping command e Ifyou are accessing the WMIC through a Telnet session and you do not have a valid username make sure that the current FTP username is the one that you want to use for the FTP download You can enter the show users privileged EXEC command to view the valid username If you do not want to use this username create a new FTP username by using the ip ftp username username global configuration command This new name will be used during all archive operations The new username is stored in NVRAM If you are accessing the WMIC through a Telnet session and you have a valid username this username is used and you do not need to set the FTP username Include the username in the archive download sw or archive upload sw privileged EXEC command if you want to specify a username for that operation only e When you upload an image file to the FTP server it must be properly configured to accept the write request from the user on the WMIC For more information refer to the documentation for your FTP server Downloading an Image File by Using FTP You can download a new image file and overwrite the current image or keep the current image A Caution For the download and upload algorithms to operate properly do not rename image directories Cisco 3200 Series Router Hardware Reference OL 5816 10 M 7 23 Chapter

Cisco Systems 3200 Network Router User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents