Chauvet CH-209 Automobile Alarm User Manual
Contents
1. Congratulations on the purchase of your new CHAUVET lighting effect We are confident you will enjoy many trouble free hours with this unit To assist with the care and use of the product we have prepared this short guide Operation Before connecting this unit to the mains power supply for the first time you must first install the lamp See Replacing Lamps for details This lighting effect has been designed to function on a mains power supply of either 120V 60Hz or 230V 50Hz and has been fitted with a suitable power plug for use with your local voltage Check the label and voltage selector switch if fitted on the unit and the power plug for the correct voltage When connected to the mains power supply the unit should illuminate and the head should rotate You can adjust the speed of rotation with the rotary speed control located at the rear of the unit fig 1 FREE speed controller To utilize the speed control simply plug the controller into the 1 4 jack on the fixture Turn the knob on the controller to adjust the rotation of the fixture to the desired speed Due to the high operating temperature of halogen lamps it is advisable that the effect be used in well ventilated areas taking care not to obstruct the air vents After use allow time to cool for safety and to ensure lamp life before moving or touching The duty cycle for this effect should be no more than 15 minutes on then 15 minutes off Installation Mount2. power supply i e the head does not rotate Then it is highly likely that the fuse has blown Disconnect from main power supply before attempting to replace either lamps or fuse In order to replace the fuse disconnect from the main power supply first and then unscrew the fuseholder cover to reveal the fuse The unit has a label attached which indicates the correct fus rating and you will also find this listed as part of the specifications for the unit later in this guide is most important that replacement fuses are of the correct rating Failure to use the correct fuse could damage the lighting effect beyond economic repair The fuse should simply be placed inside the holder and the screw cap replaced when this is done connect to the main power supply to check If the unit is still not working then please conta CHAUVET for servicing Cleaning The most important part of your lighting effect to keep clean are the lenses as they allow the ligh output to transmit These should be cleaned with a soft damp cloth The body of the unit may als be cleaned in the same way We recommend internal cleaning be carried out by a fully qualified technician Maintenance amp Servicing Work on internal parts should be carried out by a qualified technician Removal of any covers other than the lamp replacement access or the fuseholder is considered a breach of warranty an will not be covered under any such agreement unless authorized first by CHAUVE
3. Caution Do not obstruct the air vents Do not touch unit or lamps while hot No user serviceable parts inside please refer to CHAUVET for service Power Connections The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration Earth Green Yellow cable Neutral Blue cable Live Brown cable In the USA amp Europe it is required that all plugs are 3 pin type i e with Earth Ground connection In the UK it is required that all mains plugs are fitted with 5A fuses Technical Specifications Power 120V 60Hz AC 230V 50Hz AC Fuse 20mm Glass 3 15A Fast Blow 20mm Glass 1 6A Fast Blow Lamps S 120V 300W 1 x 230V 300W art No 64514 Part No 64516 Dimensions 203 x 254 x 254mm 8in x 10in x 10in Weight 3 6kg 7 92lbs User Information Please complete for your records Date Purchased Serial No Dealer Stamp Model CH 209 ALIEN Innovation Performance Alien CH 209 Users Guide Please read these instructions carefully before us Word wide Headquarters 3000 North 29 Ct Hollywood Horida USA FL 33020 Tel 1 954 929 1115 Fax 1 954 929 5560 www C hauvetlighting com e Lamp Replacement Cover At the Rear Screw Cap Colored Lenses Fuseholder Rotary Speed Control 1 4 for controller gt Voltage Selector Mounting Bracket aa Not on European Model Introduction
4. T Troubleshooting e If the unit is not functional check main power supply is on and check fuses e If the unit is functional but lamp does not light lamp may require replacing If after trying this solution you still have a problem contact CHAUVET
5. ing This unit has been designed to be hung It is recommended that for safety purposes your lighting effect be properly mounted using a suitable hanging clamp and safety cable CHAUVET offers a range of items which are ideal for safe mounting Use in a well ventilated area without obstruction to air vents Replacing Lamps 1 Disconnect from main power supply before attempting to replace either lamp or fuse 2 Ensure that the unit is sufficiently cool before removing blown lamp 3 Never touch new lamps with your fingers use a tissue or a cloth In order to replace the lamp disconnect from main power supply first and unscrew the 3 screw fixings to remove the lamp replacement cover the head of the unit which is highlighted on the diagram fig 1 Only use the appropriately rated lamp as use of any other lamp type may cause the unit to be non operational Due to the nature of halogen lamps it is vitally important that you do not touch the new replacement lamp with your fingers as this will reduce lamp life considerably Once again a tissue or cloth can be used for fitting the replacement lamp Finally before using check that the lamp is housed correctly in the lamp holder and that the lamr replacement cover has been screwed back into place If after replacement of the lamp the unit is still not working then please contact CHAUVET for servicing Replacing Fuses If the unit does not function at all when connected to the main
Download Pdf Manuals
Related Search