Blue Sea Systems 6011 Switch User Manual
Contents
1. 11 dB 100 Hz 11 dB 10 kHz 600 uV 85 mV 75 mV 8 16 ohms 25V and 70V transformer isolated balanced or unbalanced 4 ohms direct unbalanced Speaker screw terminal strip TAPE BOOSTER jack WMT1A jack 2 MIC Lo Z terminals 2 AUX Hi Z jacks Tel MIC1 MIC2 AUX1 switch selected AUX 2 BASS TREBLE TEL VOX 120V AC 60 Hz 85W 148W 220 14 x 3 x 11 D all models 16 Ib 18 Ib 20 Ib All specifications subject to change without notice Power Switch Indicator is OFF Power Switch Indicator is ON Power Switch Indicator is ON Volume Controls are turned up Unit is extremely hot Little volume Power Switch Indicator is ON Volume up Good volume Power Switch Indicator is ON Volume controls are in normal operational position Power Switch Indicator is ON Volume controls are in normal operational position Amplifier not plugged in AC outlet dead Power switch off Circuit breaker tripped No signal from source Volume turned down Speakers not connected correctly Link jumper not set correctly pg 5 Partial short on the output Check speakers and wires Signal from source is already distorted Input signal too large for input type reduce signal level applied to input Poor speaker connections Transformer output load on wrong tap Bass control boosted too much Output too great for speakers reduce level Speakers wired out of phase Bass con2. YE HER ERE SO UR 7 VOX SENSitivity Control citta tetti erst it ta ea a vai Mea eb Reo do 7 SPECIFICATIONS ree HR 8 gidesB uBiiieec 9 WARRANTY de 10 pieioiz o 1 10 Classic dries Y ill MIC 1 MIC 2 AUX1 AUX2 TREBLE BASS POWER 4 6 4 6 4 6 0 0 aw aw aN E 5 2 2 O OR AOE XO E 4 Gi 0 10 o 10 0 10 CUT BOOST CUT BOOST BOGEN 1 MIC1 Level Control Individual level control for a dedicated microphone input 2 MIC2 AUX1 Mode Switch Switch selects either the MIC2 or AUXT connection as the active input 3 MIC2 AUX1 Level Control Individual level control for a dedicated microphone input or for an auxiliary input depending on input mode selected 4 AUX2 Level Control Individual level control for a dedicated auxiliary input 5 Treble Control Controls the amount of cut or boost of treble frequencies above 10 kHz 6 Bass Control Controls the amount of cut or boost of bass frequencies below 100 Hz 7 Power AC Power switch llluminates when ON Classic Series Rear Panel 625 N MIC2 MIC1 GND COM LINK 4f 25V 16 N 70V GND GND GND eG 9G VOUOYVQ e QOQOQQGQ
3. o CLASS 2 WIRING ACCEPTABLE TAPEIBOOSTER WMT 1A AUX2 MUTE AUX2 AUXI BOGEN e e 2 f SN OUTPUT RATING 100W TEL TEL amp GND 120VAC 60Hz w 25A HOLD CAUTIC D VOX YZ SAME TYPE AND RATING lt gt 1 Amplifier Output Screw terminal strip containing all available speaker outputs 2 Tape Booster RCA unbalanced signal level output 3 WMT1A RCA output connection for Bogen s 600 ohm balanced line matching transformer Model WMT1A 4 AUX Terminal Screw terminal connection that allows externally controlled muting of AUX inputs with a contact closure 5 Microphone Inputs Screw terminal strip containing the MIC1 and MIC2 balanced low impedance inputs MIC2 is switch selectable 6 Auxiliary Inputs RCA unbalanced AUX1 and AUX2 high impedance inputs AUX1 is switch selectable 7 TEL Input Screw terminal input for 600 ohm balanced telephone signal 8 VOX SENS Control Variable control for adjusting TEL input signal level trigger point for automatic muting of Aux input 9 TEL Volume Control Adjusts the telephone input paging level Installation Package Contents Classic Series Amplifier Instruction Manual Ventilation When using a shelf or table mount the amplifier should stand alone with n
4. Classic Series Amplifiers C35 C60 amp C100 Models Installation and Use Manual 2003 Bogen Communications Inc All rights reserved Specifications subject to change without notice 54 5979 02B 0307 Printed in Korea Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing However information is subject to change Important Safety Information WARNING To Reduce The Risk of Fire Or Electric Shock Do Not Expose This Apparatus To Rain Or Moisture Always follow these basic safety precautions when installing and using the unit DN OS UT o paa X 10 11 12 13 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth DO NOT block any ventilation openings Install in accor dance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Pr
5. LIED AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW Bogen s liability arising out of the manufacture sale or supplying of products or their use or disposition whether based upon warranty contract tort or otherwise shall be limited to the price of the product In no event shall Bogen be liable for special incidental or consequential damages including but not limited to loss of profits loss of data or loss of use dam ages arising out of the manufacture sale or supplying of products even if Bogen has been advised of the possibility of such damages or losses Some States do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from State to State Products that are out of warranty will also be repaired by the Bogen Factory Service Department same address as above or call 201 934 8500 The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service Department All shipping charges in addition to parts and labor charges will be at the owner s expense All returns require a Return Authorization number Accessories RPK50 Rack Mounting Kit e Adapts Classic Series amps Models C35 C60 and C100 for 19
6. esecssasscssesessssecsseseseses 2 3 Classie Series Front Panel tette rera re Er ee ERES ER EVER ENNEN 2 Classic Series Rear Panel cct eire er e red 3 INSTALLATION rr 4 Package Contents jm 4 MentilatiOh ante rt eei o te e tr ha dv en aaa aon e bc cease onesies 4 Rack MOUNDE Eee 4 CONNECTIONS 5 Input Connections e EEan 5 Microphone Connections mtd t n tested t sia rosa Reuse 5 PUSH GUY p M 5 DOLO m 5 pim Output Connections Speakers General Speakers Low Impedance Tape Booster Connection WMT 1A Connection OPERATION ge O Front Panel Controls eei teet teet n Eos e eo e co esie eH Ca UR ee EE eo o De Re Rd 6 a AAEE E EEEN iiiter i er itia c vates ei revera teres vedete red 6 Input Volume Conttols itte tiroteo tts passae hoste b i Ree Rabe RAP RAE PAP Reo 6E aee shies 6 MIC2 AUX 1 Mode Switch iie ERE REM TG I HER 6 Base and Treble Controls cccssssssssssescsssesescsesesescsesssssccesessscsssesesssesesescseseseseseseesseseeseaseenenesenens 6 Rear Panel Controls oso rd iode ETT UP RTT P MD E E Reda 7 TEL Volume Control aree vera Oa ERR
7. he level VOX SENSitivity Control When an input signal such as voice is detected through the TEL input the music channels AUX1 and AUX2 will be muted The VOX SENSitivity con trol should be set so that only the desired signal is above the threshold level while noise and unwanted signal is below it To adjust the sensitivity of this cir cuit 1 Rotate the control fully clockwise While making a page announcement and talking at a low level the sound should not be choppy nor missing parts of words If it is choppy or if intelligibility is poor rotate the control counterclockwise to the point where the sound is clear and crisp but not to the maximum counterclockwise position 2 If the background music shuts down when no page is in progress rotate the control clockwise until the music is restored Power Output RMS C35 C60 C100 Frequency Response amp Distortion Transformert 4 Ohm Direct Output Hum and Noise MIC Input AUX Input TEL Input Tone Control Action Bass Treble Input Sensitivity MIC Lo Z Balanced AUX TEL Outputs Output Connections Input Connections Controls Power Requirements AC Line Draw C35 C60 C100 Dimensions Product Weight C35 C60 C100 T Measured 2 dB below FRP 35W 60W 100W 70 16 kHz 2 dB 1 max 20 20 kHz 1 dB 0 5 max 55 dB below rated output 70 dB below rated output 70 dB below rated output
8. o equipment on top of it or below it If the amplifier must be stacked with other equipment care must be taken to ensure that all the minimum clearance distances h are met and that the equipment below the amplifier produces little significant heat Rack Mounting A rack mount bracket kit Model RPK50 is available as an accessory Not included Connections Input Connections Microphone Connections MIC2 MIC GND GND These inputs are for two low impedance balanced dynamic microphones Connect cable shield to center screw marked GND 56 S SS S S Auxiliary AUX2 AUX1 The AUX inputs provide unbalanced RCA inputs for connection to external signal level equipment e AUX Muting For this function a customer supplied normally open contact closure switch must be connected to the AUX 2 MUTE terminals When the contacts are closed the AUX 2 input will be muted Typically activated by e a switch in a push to talk style microphone AUX 1 if selected is not mutable by contact closure AUX2 MUTE TEL Connect the telephone line to the two outside terminals and the shield if used to the center terminal TEL input signal will trigger automatic te muting of AUX 1 and AUX 2 Input impedance is 600 ohm and is trans former balanced Input is for Dry audio signals only no DC voltage on the signal Output Connection
9. otect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufac turer Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning flash with arrowhead sym bol within an equilateral triangle is intended to alert the user to the pres ence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equi lateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompa nying the appliance Contents Page PANEL DESCRIPTIONN S eoe na anon noo ern uai sseascesoscscevscavesscscassss
10. rack mounting 2 rack spaces 3 1 2 Heavy gauge steel construction WMT1A Matching Transformer Hi Z 10k ohm primary impedance e Lo Z 600 ohm secondary impedance balanced with center tap e Matches high impedance unbalanced or low impedance balanced signals e Jumper selection allows line level signal to microphone level signal conversion lt BOGEN COMMUNICATIONS INC 50 Spring Street Ramsey NJ 07446 U S A Tel 201 934 8500 Fax 201 934 9832 www bogen com 10
11. rive long cable runs Front Panel Controls Power The front panel ON OFF switch applies power to the amplifier and is illumi nated when power is ON Input Volume Controls Each input module may be individually controlled by its corresponding volume control knob MIC2 AUX 1 Mode Switch Activates the corresponding input that it is switched to MIC2 or AUX1 The other input is inactive and any connections to the inactive input will not work MIC2 AUX1 Bass and Treble Controls The Bass and Treble controls are used to adjust the tonal balance of the ampli fier output The center position of these controls provides flat frequency response Counterclockwise rotation of these controls reduces the bass or treble response while clockwise rotation increases such response The treble control has a cut boost range of 11 dB at frequencies above 10 kHz and provides a roll off after 20 kHz to reduce gain above the audio range The bass control has a cut boost range of 11 dB at frequencies below 100 Hz When driving speakers using the direct coupled output terminals the bass filter s response is flat to 20 Hz Rear Panel Controls TEL Volume Control The TEL VOLUME control on the rear panel adjusts the TEL input s paging level It does not affect the microphone level Rotate the control counter TEL 6 clockwise to decrease the level Rotate the control clockwise to increase t
12. s Speakers General The amplifier may be used with most conventional speaker sys M tems Connect one speaker lead to the screw terminal that cor GND COM LNK 4N 25 7V GND responds to the impedance of the type of speakers used in the T V system and the other lead to the COM terminal If the line is 9 G e VO OO 9 shielded connect the shield to GND Connecting the GND to the COM terminal when using the trans former coupled outputs references the transformer output to ground Disconnecting the GND terminal from COM allows the transformer output to float electrically This is sometimes useful under certain conditions where a ground connection is undesir able It is generally a good idea to short the GND to the COM terminal regardless of output type Trans or Direct LINK 4f Speakers Low Impedance To connect a 4 ohm speaker remove the the 4 ohm link and connect the speaker between 4 ohm and GND Tape Booster Connection To tape record the amplifier program connect a patch cord from the TAPE BOOSTER output jack to the input of a tape recorder Can also be connected to the input of a booster amplifier WMT1A Connection TAPE BOOSTER WMT 1A This output jack is directly connected to the 25V speaker tap and permits e the connection of Bogen s general purpose matching transformer WMT1A The WMT1A steps the signal down by a 5 1 ratio giving you a 600 ohm balanced signal that can d
13. trol set to cut side Note Transformer coupled speakers have less bass response Poor electrical connections at input Shields of cables not connected Input cable routed near AC cables power transformer or other EMI radiating devices Electrically noisy devices operating on the same AC circuit Poor equipment grounding Ensure that all AC safety grounds are connected Make sure that all components in audio chain are tied to the same ground Warranty Bogen Classic Series Amplifiers are warranted to be free from defects in material or workmanship for two 2 years from the date of sale to the original purchaser Any part of the product covered by this warranty that with normal installation and use becomes defective will be repaired or replaced by Bogen at our option provided the product is shipped insured and prepaid to Bogen Factory Service Department 50 Spring Street Ramsey NJ 07446 USA The product will be returned to you freight prepaid This warranty does not extend to any of our products that have been subjected to abuse misuse improper storage neglect accident improper installation or have been modified or repaired or altered in any manner whatsoever or where the serial number or date code has been removed or defaced THE FOREGOING LIMITED WARRANTY IS BOGEN S SOLE AND EXCLUSIVE WARRANTY AND THE PUR CHASER S SOLE AND EXCLUSIVE REMEDY BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND EITHER EXPRESS OR IMP
Download Pdf Manuals
Related Search